Академический Документы
Профессиональный Документы
Культура Документы
Dimensional specifications
Gypframe profiles
Dimensional specifications data sheet
Introduction
This data sheet contains the dimensional specification of the All British Gypsum system solutions listed in the The White Book
following Gypframe components Gypframe Studs, Gypframe and British Gypsum Site Book are covered by SpecSure, a lifetime
Channels, CasoLine mf, GypLyner, ShaftWall, GypFloor silent, system warranty designed to protect the integrity of British
GypWall rapid dB Plus, Gypframe CurveLyner Channel, Gypsum specifications and deliver reliable performance, unrivalled
Gypframe Steel Angles and Gypframe Specialist Profiles. technical support and peace of mind for everyone involved in the
construction team. The SpecSure warranty is invalid if you change
Gypframe profiles are cold roll formed from DX51D + Z140 NA-C, any component, as this will affect the system performance.
1
utilizing the patented UltraSTEEL process.
General
Cold Rolling and UltraSTEEL
Information on the installation and handling of British Gypsum
UltraSTEEL is a manufacturing process that alters the systems and Gypframe profiles can be found in the British Gypsum
characteristics of plain steel, providing higher strength capacity at a Site Book. For health and safety guidance, handling, storage
lighter gauge. The process effectively hardens the steel by working information, please use the Gypframe Health and Safety datasheet.
it in strips with two mating rolls, which produce a dimpled surface
and ribbing effect across the surface of the metal. During the All literature is available to download from british-gypsum.com
process, the effective thickness of the material is increased to that
of the original thickness plus that of the ribbing. Fixing
Either British Gypsum Wafer Head Drywall Screws or British Gypsum
Example: Base gauge = 0.5mm : after UltraSTEEL process = 1.0mm
Wafer Head Jack-Point Screws should be used to fit two sections of
metal together - see table below:
Once the UltraSTEEL process has been applied, the base material
is then passed through a series of contoured rollers which
British Gypsum Wafer Head British Gypsum Wafer Head
progressively form the steel into the required profile.
Drywall Screws Jack-Point Screws
Metal-to-metal greater than
The number of rollers in the process will vary, depending on the Metal-to-metal up to 0.79mm thick
0.80mm thick
complexity of the profile being rolled. Service entries or tabs are
Stud framing up to 0.50mm thick Studs greater than 0.50mm thick
pierced, either at the beginning or end of this process. The formed
profiles are then cut to exact length, packed and then bundled ready
Either British Gypsum Drywall Screws or British Gypsum
for delivery.
Jack-Point Screws should be used for fixing plasterboard to metal.
Screw length should be based on board thickness and reaching a
UltraSTEEL is unique to British Gypsum and the Gypframe product
minimum of 10mm penetration into a metal stud.
range. Along with an aesthetic difference, UltraSTEEL provides the
following additional benefits over plain steel sections:
Example: 2 x 15mm Gyproc WallBoard + stud gauge + 10mm
Improved yield strength = minimum 42mm British Gypsum Drywall Screw
Improved load carrying capacity
British Gypsum Drywall Screws British Gypsum Jack-Point
Improved screw retention and strip out strength
Screws
Improved resistance to screw pull-out Metal-to-metal greater than
Metal-to-metal up to 0.79mm thick
0.80mm thick
Standards Stud framing up to 0.50mm thick Studs greater than 0.50mm thick
Gypframe metal products are produced to the European
manufacturing standard EN 14195: 2005 and are manufactured The first 2 or 3 digits of a component code refer to the component
under a quality system independently audited and certified as width, the letters refer to the component type and the last two
conforming to ISO 9001: 2005. The EN 14195: 2005 standard does digits indicate metal thickness or gauge in mm (see example below).
not cover component design or system performance.
Example:
Do not assume products manufactured to this standard can be
substituted, as system performance will be changed.
UltraSTEEL is a registered trade mark of Hadley Industries Component width in mm - Example = 60mm
Overseas Holdings Limited. Component type - Example = Stud Stud gauge - Example = 0.50mm
Gypframe studs
Used as the vertical support in wall framing, these products are available in a range of widths, lengths and gauge depending on
requirements for strength, height, impact resistance and sound insulation ( Profile drawings on page 7).
Gypframe C Studs
The Gypframe C Stud design includes sight lines down the legs of the stud to ease board alignment and increase profile strength.
Structural apertures are also spaced along the spine of the Gypframe C Stud, providing easy routing of services through a partition.
Gypframe AcouStuds
These unique shaped studs are used for increased acoustic performance, with the patented profile absorbing sound as it passes through
a wall. Gypframe AcouStuds can be used to upgrade the acoustic performance of 43mm, 70mm and 146mm wall systems without using
insulation. The Gypframe AcouStud design includes sight lines for both board alignment and added profile strength. Gypframe Acoustuds
have wider flange widths than Gy pframe C Studs, providing increased board fixing area.
Gypframe I Studs
These studs are the strongest available in the Gypframe range. They allow for increased partition height, without increasing partition width,
and provide improved impact resistance. Commonly used in ShaftWall, GypLyner iwl, GypWall quiet iwl and other GypWall systems where
board fixing strength is paramount. Structural apertures are also spaced along the spine of the Gypframe I Stud, providing easy routing of
services through a partition.
Gypframe Standard, Deep Flange and Extra Deep Flange Floor & Ceiling Channels
These products are used for retaining wall studs at floor and ceiling junctions. Although Standard (C) channels are the most
commonly used, Deep Flange (DC) and Extra Deep Flange (EDC) versions are available for partitions over 4200mm high and 8000mm
high respectively, or in situations where deflection head details, improved impact resistance and easier skirting fixing are required
( Profile drawings on page 7).
Fixing channels
Used for a variety of applications including cross bracing on twin frame wall systems and fixing of medium to heavy weight fittings.
Gypframe 99 FC 50 Fixing Channel: used for bracing twin frame wall systems and medium weight fixtures to BS 5234.
Gypframe Service Support Plate used for the installation of plywood within a partition cavity ( Profile drawings on page 10).
Studs
34mm
38mm
55mm
6.5mm
WIDTH
WIDTH
146mm
18mm
12mm
33mm 48 50, 60 50, 60 70,
70 50, 70 70, 92 90,
48 S 50, 60 S 50, 70 S 50, 146 80
70 S 60, 92 S 50, 92 S 60,
92 S 10, 146 S 50
146 T 90
43mm
6mm
42mm
WIDTH
32mm
43mm
7mm
41mm
43 AS 50
70 AS 50, 92 AS 50,
146 AS 50 Bracketed figures indicate gauge.
Channels
Gypframe Standard, Deep Flange and Extra Deep Flange Floor and Ceiling Channel
WIDTH
12mm
WIDTH
WIDTH
70mm
55mm
18mm
50mm
32mm
146mm
Starter Channel Standard C Deep Flange DC Extra Deep Flange EDC
(146 TSC 90) (50 C 50, 62 C 50, 72 C 50, ( 50 DC 60, 62 DC 60, 72 DC 60, ( 50 EDC 70, 72 EDC 80,
94 C 50, 148 C 50) 148 DC 60, 94 DC 60) 94 EDC 60, 148 EDC 80)
15mm
15mm
WIDTH
70mm
67mm
50mm
45mm
35mm
32mm
Starter Channel Head J G102 Retaining Channel G105 Retaining Channel G110 Retaining Channel
(60 SC 55, 70 SC 70, (50/70mm deep flanges (60mm and 146mm studs - (92mm studs - ShaftWall) (70mm studs - ShaftWall)
92 SC 90) 62 JC 70) ShaftWall)
32mm
70mm
Channels (continued)
18mm
48mm 102mm
44mm 98mm
Gypframe MF5 Ceiling Section Gypframe MF6 Perimeter Gypframe MF7 Primary Gypframe MF7C Curved
Channel Section Support Channel Support Channel
45mm
45mm
30mm
52mm
(0.50mm) (0.50mm) (0.90mm) (0.90mm)
Gypframe MF8 Strap Gypframe MF9 Gypframe FEA1 Gypframe MF11 Nut & Bolt
Hanger Connecting Clip Steel Angle
25mm
25mm 25mm
60mm
6mm dia.
(0.50mm)
25mm bolt 12mm long
(0.5mm)
94mm
Gypframe GAH1 Acoustic Hanger Gypframe GAH2 Acoustic Hanger Gypframe MF12 Soffit Cleat
27mm
25mm
37mm
70mm
30mm 35mm
(1.5mm)
Gypframe GL1 Channel Gypframe GL3 Channel Connector Gypframe GL10 Steel Framing Clip
(0.50mm) 16mm
18mm
45mm
90mm
60mm
43mm
43mm
6mm
(0.50mm)
Gypframe GL8 Track Gypframe MF10 Channel Gypframe GL5 Timber Connector
21mm
(0.50mm) (0.55mm)
27mm
44mm
10mm
50mm
30mm
Gypframe RB1 Resilient Bar Gypframe RB2 SureFix Bar Gypframe GL6 Timber Connector
16mm
171mm
10mm
9.5mm
6mm
21mm 15mm
27mm
44mm
45mm 35mm
(0.45mm) (0.50mm)
Gypframe SIF1 Floor Channel Gypframe SIF2 Floor Channel Gypframe SIF4 Floor Channel
20mm
20mm
195mm
75mm
12mm
48mm
(1.00mm)
As supplied 26 no.
4.25 dia. holes 10mm As installed
295mm
12mm
125mm
125mm 45mm 125mm
29mm
48mm
(1.00mm)
As supplied 46 no.
4.25 dia. holes 10mm As installed
395mm
175mm
12mm
48mm
(1.00mm)
As supplied 66 no.
4.25 dia. holes 10mm As installed
Steel angles
Gypframe FEA1 / GA2 Gypframe GA3 Steel Angle Gypframe GA5 Internal Gypframe GA6 Splayed
Steel Angle Fixing Angle Angle
25mm
10mm
m
50mm
m
85
25mm
(0.5 / 0.7mm)
135
25mm
60mm
Gypframe GA4 Steel Angle (0.7mm)
85mm
32mm
60mm 10mm
(0.50mm) (0.50mm)
19mm
Miscellaneous sections
25mm 5mm
23mm
459mm
Gypframe G106 Skirting Plate Gypframe 99 FC 50 Fixing Channel Gypframe SC1 Gypframe SC2
Spacer Clip Spacer Clip
9.5mm
17mm 17mm
99mm
100mm
55mm
10mm
(0.50mm)
11mm
25mm
25mm
14mm 40mm
(0.60mm)
Gypframe Service Support Plate Gypframe GTF1 Fixing T Gypframe GFS1 Fixing Strap
18mm
106mm 50mm
70mm
46mm
(0.55mm)
(140mm long
Saint-Gobain Construction Products UK Limited is a limited company registered in England under company number 734396, having its registered office at Saint-Gobain House, Binley
Business Park, Coventry, CV3 2TT, UK. Saint-Gobain Construction Products UK Limited trades as British Gypsum for part of its business activities.
British Gypsum reserves the right to revise product specification without notice. The information herein should not be read in isolation as it is meant only as guidance for the user, who
should always ensure that they are fully conversant with the products and systems being used and their subsequent installation prior to the commencement of work. For a comprehensive
and up-to-date library of information visit the British Gypsum website at: british-gypsum.com. For information about products supplied by Artex Limited or Saint-Gobain Isover please see
their respective websites.
british-gypsum.com