Академический Документы
Профессиональный Документы
Культура Документы
Multi Channel AV
Receiver
Operating Instructions
STR-DH800
2009 Sony Corporation
Disposal of waste batteries
WARNING (applicable in the European
Union and other European
To reduce the risk of fire or electric countries with separate
shock, do not expose this apparatus to collection systems)
rain or moisture. This symbol on the battery or on the packaging
To reduce the risk of fire, do not cover the indicates that the battery provided with this product
ventilation opening of the apparatus with shall not be treated as household waste.
newspapers, tablecloths, curtains, etc. Do not place On certain batteries this symbol might be used in
the naked flame sources such as lighted candles on combination with a chemical symbol. The chemical
the apparatus. symbols for mercury (Hg) or lead (Pb) are added if
the battery contains more than 0.0005% mercury or
Do not install the appliance in a confined space, such 0.004% lead.
as a bookcase or built-in cabinet.
By ensuring these batteries are disposed of correctly,
To reduce the risk of fire or electric shock, do not you will help prevent potentially negative
expose this apparatus to dripping or splashing, and consequences for the environment and human health
do not place objects filled with liquids, such as which could otherwise be caused by inappropriate
vases, on the apparatus. waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
As the main plug is used to disconnect the unit from
In case of products that for safety, performance or
the mains, connect the unit to an easily accessible
data integrity reasons require a permanent
AC outlet. Should you notice an abnormality in the
unit, disconnect the main plug from the AC outlet connection with an incorporated battery, this battery
immediately. should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
Do not expose batteries or apparatus with battery- hand over the product at end-of-life to the applicable
installed to excessive heat such as sunshine, fire or collection point for the recycling of electrical and
the like. electronic equipment.
The unit is not disconnected from the mains as long For all other batteries, please view the section on
as it is connected to the AC outlet, even if the unit how to remove the battery from the product safely.
itself has been turned off. Hand the battery over to the applicable collection
point for the recycling of waste batteries.
Excessive sound pressure from earphones and For more detailed information about recycling of
headphones can cause hearing loss. this product or battery, please contact your local
Civic Office, your household waste disposal service
For customers in Europe or the shop where you purchased the product.
Disposal of Old Electrical &
Electronic Equipment Notice for customers: The following
(Applicable in the European information is only applicable to
equipment sold in countries applying
Union and other European
EU Directives.
countries with separate
The manufacturer of this product is Sony
collection systems) Corporation, 1-7-1 Konan Minato-ku Tokyo,
This symbol on the product or on its packaging 108-0075 Japan. The Authorized Representative for
indicates that this product shall not be treated as EMC and product safety is Sony Deutschland
household waste. Instead it shall be handed over to GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
the applicable collection point for the recycling of Germany. For any service or guarantee matters
electrical and electronic equipment. By ensuring this please refer to the addresses given in separate
product is disposed of correctly, you will help service or guarantee documents.
prevent potential negative consequences for the
environment and human health, which could For customers in Australia
otherwise be caused by inappropriate waste
handling of this product. The recycling of materials Disposal of Old Electrical &
will help to conserve natural resources. For more Electronic Equipment
detailed information about recycling of this product, (Applicable in the European
please contact your local Civic Office, your Union and other European
household waste disposal service or the shop where countries with separate
you purchased the product. collection systems)
2GB
For customers in United
Kingdom, Europe and On Copyright
Australia This receiver incorporates Dolby* Digital and Pro
This symbol is intended to alert Logic Surround and the DTS** Digital Surround
the user to the presence of the Hot System.
Surface that may be hot if it is * Manufactured under license from Dolby
touched during the normal Laboratories. Dolby and the double-D symbol
operation. are trademarks of Dolby Laboratories.
** Manufactured under license under U.S. Patent
#s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
About This Manual 7,392,195; 7,272,567 & other U.S. and
worldwide patents issued & pending. DTS is a
The instructions in this manual are for model registered trademark and the DTS logos, Symbol,
STR-DH800. Check your model number by DTS-HD and DTS-HD Master Audio are
looking at the lower right corner of the front panel. trademarks of DTS, Inc. 1996-2008 DTS, Inc.
In this manual, models of area code CEL is used All Rights Reserved.
for illustration purposes unless stated otherwise.
Any difference in operation is clearly indicated in This receiver incorporates High-Definition
the text, for example, Models of area code CEK Multimedia Interface (HDMITM) technology.
only. HDMI, the HDMI logo and High-Definition
The instructions in this manual describe the Multimedia Interface are trademarks or registered
controls on the supplied remote. You can also use trademarks of HDMI Licensing LLC.
the controls on the receiver if they have the same
or similar names as those on the remote. This product is manufactured under license from
Neural Audio Corporation and THX Ltd. Sony
About area codes Corporation hereby grants the user a non-exclusive,
The area code of the receiver you purchased is non-transferable, limited right of use to this product
shown on the lower right portion of the rear panel under USA and foreign patent, patent pending and
(see the illustration below). other technology or trademarks owned by Neural
Audio Corporation and THX Ltd. Neural
2 IN 1 OUT
Surround, Neural Audio, Neural and NRL
are trademarks and logos owned by Neural Audio
SURROUND
Corporation, THX is a trademark of THX Ltd.,
R L
FRONT A
which may be registered in some jurisdictions. All
rights reserved.
R L
3GB
Table of Contents
Description and location of parts...................6
Enjoying Surround Sound
Enjoying a pre-programmed sound field .... 59
Getting Started Enjoying the surround effect at low
1: Installing the speakers .............................16 volume levels (NIGHT MODE) ............ 64
2: Connecting the speakers ..........................17 Using only the front speakers
3: Connecting the TV ..................................20 (2CH STEREO) ..................................... 65
4a: Connecting the audio components.........22 Listening to the sound without any
4b: Connecting the video components ........23 adjustment (ANALOG DIRECT) .......... 65
5: Connecting the antennas (aerials)............30 Resetting sound fields to the initial
6: Preparing the receiver and the remote .....30 settings ................................................... 66
7: Selecting the speaker system ...................32
8: Calibrating the appropriate settings
automatically
Tuner Operations
(AUTO CALIBRATION) .......................32 Listening to FM/AM radio.......................... 66
9: Adjusting the speaker levels and Presetting FM/AM radio stations................ 68
balance (TEST TONE) ...........................39 Using the Radio Data System (RDS).......... 71
(Models of area code CEL, CEK only)
Playback
Selecting a component.................................40 BRAVIA Sync Features
Listening/Watching a component ................42 What is BRAVIA Sync? .......................... 72
Preparing for the BRAVIA Sync ............. 73
Watching a DVD/Blu-ray disc
Amplifier Operations (One-Touch Play)................................... 75
Navigating through menus...........................44 Enjoying the TV sound from the speakers
Adjusting the level (LEVEL menu).............49 connected to the receiver
Settings for the speakers (System Audio Control)......................... 75
(SPEAKER menu)..................................50 Turning off the receiver with the TV
Settings for the surround sound (System Power Off) ............................... 76
(SURROUND menu)..............................53
Adjusting the equalizer (EQ menu).............54
Settings for the tuner (TUNER menu).........54 S-AIR Operations
Settings for the audio (AUDIO menu).........55 About S-AIR products ................................ 76
Settings for the video (VIDEO menu).........56 Setting up an S-AIR product....................... 77
Settings for the HDMI (HDMI menu).........56 Enjoying the systems sound in another
Settings for the system (SYSTEM menu) ...57 room ....................................................... 81
Settings for the S-AIR (S-AIR menu) .........58 Changing the channel
for better sound transmission ................. 83
Enjoying the S-AIR receiver while the
S-AIR main unit is in standby mode...... 84
4GB
Other Operations
Switching between digital and analog
audio (INPUT MODE) .......................... 85
Enjoying the sound/images from other
inputs...................................................... 85
Enjoying the DIGITAL MEDIA PORT
(DMPORT) ............................................ 87
Changing the display................................... 89
Using the Sleep Timer................................. 90
Recording using the receiver....................... 90
Using a bi-amplifier connection.................. 91
Additional Information
Glossary ...................................................... 99
Precautions ................................................ 102
Troubleshooting ........................................ 104
Specifications ............................................ 110
Index.............................................. Back cover
5GB
Description and location of parts
Front panel
1 2 3 4 5 6 7 8
MASTER VOLUME
?/1
TONE INPUT SELECTOR
SPEAKERS
MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
qh qg qf qd qs qa q; 9
6GB
Name Function
L 2CH/A.DIRECT Press to select a sound field
(page 59).
A.F.D.
MOVIE
MUSIC
M TUNING MODE Press to operate a tuner
(FM/AM) (page 66).
TUNING +/
MEMORY/
ENTER
N INPUT MODE Press to select the input
mode when the same
components are connected
to both digital and analog
jacks (page 85).
O PHONES jack Connects to headphones
(page 104).
P SPEAKERS Press to select the front
speaker system (page 32).
7GB
About the indicators on the display
1 2 3 4 5 6 7 8 9
wa w; ql 3 qk qj qh qg qf qd qs qa 0
8GB
Name Function Name Function
H SP A/SP B/ Lights up according to the Q DTS-HD Lights up one of the respective
SP A+B speaker system used (page 32). indicators indicators when the receiver is
However, these indicators do decoding the corresponding
not light up if the speaker output DTS-HD format signals.
is turned off or if headphones
are connected. DTS-HD DTS-HD Master Audio
MSTR
I SLEEP Lights up when the sleep timer DTS-HD HI DTS-HD High Resolution
is activated (page 90).
RES Audio
J A.DIRECT Lights up when the receiver is
R LPCM Lights up when Linear PCM
processing Analog Direct
signals are detected.
signals.
S DMPORT Lights up when DIGITAL
K Tuning Lights up when the receiver MEDIA PORT adapter is
indicators tunes in radio stations.
connected and DMPORT is
selected.
MEM Lights up when a memory
function, such as Preset T HDMI Lights up when the receiver
Memory (page 68), etc., is recognizes a component
activated. connected via an HDMI IN jack
MONO Monaural broadcast (page 24).
RDS A station that provides RDS
services is tuned in. U Playback The letters (L, C, R, etc.)
channel indicate the channels being
Note
RDS appears for models of indicators played back. The boxes around
the letters vary to show how the
area code CEL, CEK only.
ST Stereo broadcast receiver downmixes or upmixes
the source sound (based on the
L S-AIR Lights up when the S-AIR speaker settings).
transmitter (not supplied) is
connected. L Front Left
R Front Right
M Dolby Lights up one of the respective
C Center (monaural)
Pro Logic indicators when the receiver
SL Surround Left
indicators applies Dolby Pro Logic
SR Surround Right
processing to 2 channel signals
S Surround (monaural or the
in order to output the center and
surround components obtained
surround channel signals.
by Pro Logic processing)
SBL Surround Back Left
PL Dolby Pro Logic
SBR Surround Back Right
PL II Dolby Pro Logic II
SB Surround Back (the surround
PL IIx Dolby Pro Logic IIx
back components obtained by
Note
6.1 channel decoding)
These indicators do not light up
Example:
when either the center speaker
Speaker pattern: 3/0.1
and surround speaker is not
Recording format: 3/2.1
connected.
Sound Field: A.F.D. AUTO
N BI-AMP Lights up when surround back
speakers selection is set to
BI-AMP (page 91).
O EQ Lights up when the equalizer is
activated.
P NEO:6 Lights up when DTS Neo:6
Cinema/Music decoder is
activated (page 62).
9GB
Rear panel
1 2 3 4
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
8 6 7 6 5
10GB
F AUDIO INPUT/OUTPUT section Remote commander
AUDIO IN/ Connects to a Super
White (L) You can use the supplied remote to operate the
OUT jacks Audio CD player,
etc. (page 20, 22). receiver and to control the Sony audio/video
Red (R) components that the remote is assigned to
operate.
AUDIO OUT Connects to a
Black jack subwoofer (page You can also program the remote to control
17). non-Sony audio/video components. For details,
see Programming the remote (page 95).
G VIDEO/AUDIO INPUT/OUTPUT
section RM-AAP044
AUDIO IN/ Connects to a VCR,
White (L) wj 1
OUT jacks Blu-ray disc player, THEATRE RM SET UP AV ?/1
?/1
etc. (page 27 29). wh 2
Red (R) SYSTEM STANDBY
SHIFT TV AMP 3
wg
VIDEO IN/ 1 2 3
4
Yellow
OUT* jacks VIDEO 1 VIDEO 2 BD
4 5 6
DVD SAT TV
wa 9
* You can watch the selected input image when you
connect the HDMI OUT or MONITOR OUT jack 0
to a TV (page 20, 24).
w; O qa
RETURN/ HOME TOOLS/
EXIT OPTIONS
MENU qs
. < < >
TUNING TUNING +
m M qd
DISC SKIP D.TUNING
ql X x
TV VOL TV CH
MASTER VOL PRESET
MUTING
qk qf
qj
BD/DVD
TOP MENU MENU F1 F2
qh TV INPUT WIDE
qg
continued
11GB
Name Function Name Function
A AV ?/1 Press to turn on or off the Numeric Press SHIFT (wg) and then
(on/standby) audio/video components that buttons press numeric buttons to
the remote is programmed to (number 5a)) preset/tune to preset stations.
operate. select track numbers of the
To turn the TV on or off, press CD player, VCD player, LD
TV (C) and then press AV player, DVD player, MD
?/1. deck, DAT deck, or tape
If you press ?/1 (B) at the deck. Press 0/10 to select
same time, it will turn off the track number 10.
receiver and other components select channel numbers of
(SYSTEM STANDBY).
the VCR, satellite tuner, Blu-
Note
ray disc player, PSX, DVD/
The function of the AV ?/1
VHS COMBO, or DVD/
switch changes automatically
each time you press the input HDD COMBO.
buttons (5). Press TV (3) and then press
the numeric buttons to select
B ?/1 Press to turn the receiver on or the TV channels.
(on/standby) set it to standby mode.
To turn off all components, -/-- Press SHIFT (wg) and then
press ?/1 and AV ?/1 (A) at press -/-- to select the channel
the same time (SYSTEM entry mode, either one or two
STANDBY). digit of the VCR or satellite
tuner.
Saving the power in To select the channel entry
standby mode mode of the TV, press TV (C)
When CTRL:HDMI is set to and then press -/--.
CTRL OFF (page 48) and ENT/MEM Press SHIFT (wg) and then
S-AIR STBY is set to press ENT/MEM to enter the
STBY OFF (page 48). value after selecting a channel,
C TV Press to light up the button. It disc or track using the numeric
changes the remote key buttons of the VCR, CD
function to activate the buttons player, VCD player, LD
with yellow printing. It also player, MD deck, DAT deck,
activate the (J), V/v/B/b tape deck, satellite tuner, Blu-
(J), TOOLS/OPTIONS ray disc player, or PSX.
(K), MENU/HOME (L), To enter the value of Sony TV,
RETURN/EXIT O (w;), and press TV (C) and then press
DISPLAY (wa) buttons to ENT/MEM.
perform menu operations for Press SHIFT (wg) and then
Sony TVs only. press ENT/MEM to store a
station during tuner operation.
D AMP Press to light up the button to
activate the receiver operation CLEAR/>10 Press SHIFT (wg) and then
(page 35). press CLEAR/>10 to clear a
mistake when you press the
E Input buttons Press one of the buttons to incorrect numeric button of the
select the component you want DVD player, Blu-ray disc
to use. When you press any of player, PSX, satellite tuner,
the input buttons, the receiver DVD/VHS COMBO, or DVD/
turns on. The buttons are HDD COMBO.
factory assigned to control Press SHIFT (wg) and then
Sony components. press CLEAR/>10 to select
You can program the remote to track numbers over 10 of the
control non-Sony components CD player, VCD player, LD
following the steps in player, MD deck, tape deck,
Programming the remote on TV, VCR, or satellite tuner.
page 95.
12GB
Name Function Name Function
b)
F A.F.D. Press to select a sound field M ./> Press to skip tracks of the
(page 60, 62). VCR, CD player, VCD
MOVIE
player, LD player, DVD
MUSIC player, MD deck, DAT deck,
G NIGHT MODE Press to activate the Night tape deck, Blu-ray disc player,
Mode function (page 64). PSX, DVD/VHS COMBO, or
DVD/HDD COMBO.
H SLEEP Press to activate the Sleep
Timer function and the < / < Press to replay the previous
duration which the receiver scene or fast forward the
turns off automatically. current scene of the DVD
player, Blu-ray disc player,
I AMP MENU Press to display the menu to DVD/VHS COMBO, or
operate the receiver. DVD/HDD COMBO.
J After pressing AMP (D), m/Mb) Press to
, press MENU/HOME (L) for search tracks in the forward/
V/v/B/b receiver operation, then press backward direction of the
V/v/B /b to select the CD player, VCD player,
settings. DVD player, LD player,
After pressing BD/DVD TOP MD deck, Blu-ray disc
MENU (P) or BD/DVD player, PSX, DVD/VHS
MENU (P), press V/v/B/b COMBO, or DVD/HDD
to select the settings, and then COMBO.
press to enter the fast forward/rewind of the
selection. VCR, DAT deck, or tape
Press also to enter the deck.
selection of the receiver,
N a)b) Press to start playback of the
VCR, satellite tuner, DVD
VCR, CD player, VCD
player, Blu-ray disc player,
player, LD player, DVD
PSX, DVD/VHS COMBO, or player, MD deck, DAT deck,
DVD/HDD COMBO. tape deck, Blu-ray disc player,
K TOOLS/ Press to display and select PSX, DVD/VHS COMBO, or
OPTIONS items from the options menus DVD/HDD COMBO.
for DVD player or Blu-ray Xb) Press to pause playback or
disc player. recording of the VCR, CD
To display the options of Sony player, VCD player, LD
TV, press TV (C) and then player, DVD player, MD
press TOOLS/OPTIONS. deck, DAT deck, tape deck,
Blu-ray disc player, PSX,
L MENU/HOME Press to display the menus of
DVD/VHS COMBO, or
the receiver, VCR, DVD
DVD/HDD COMBO. (Also
player, satellite tuner, Blu-ray
starts recording with
disc player, PSX, DVD/VHS
components in recording
COMBO, or DVD/HDD
standby.)
COMBO on the TV screen.
Then, use V/v/B/b and to xb) Press to stop playback of the
perform menu operations. VCR, CD player, VCD
To display the menus of Sony player, LD player, DVD
TV, press TV (C) and then player, MD deck, DAT deck,
press MENU/HOME. tape deck, Blu-ray disc player,
PSX, DVD/VHS COMBO, or
DVD/HDD COMBO.
continued
13GB
Name Function Name Function
TUNING +/ Press to scan a station. R MUTING Press to turn off the sound
temporarily. Press MUTING
D.TUNING Press to enter direct tuning
again to restore the sound.
mode.
Press TV (C) and then press
N TV CH +a)/ Press TV (C) and then MUTING to activate the TVs
press TV CH +/ to select muting function.
preset TV channels.
S DISC SKIP Press to skip disc of the CD
PRESET Press to player, VCD player, DVD
+a)/ select preset stations. player, or MD deck (multi-
select preset channels of disc changer only).
the VCR, satellite tuner,
T RETURN/ Press to
Blu-ray disc player, DVD EXIT O return to the previous menu.
player, DVD/VHS exit the menu while the
COMBO, or DVD/HDD menu or on-screen guide of
COMBO. the VCD player, LD player,
O F1, F2 Press F1 or F2 to select a DVD player, Blu-ray disc
component. player, PSX, DVD/VHS
DVD/HDD COMBO COMBO, or satellite tuner
F1: HDD mode is displayed on the TV
F2: DVD mode screen.
DVD/VHS COMBO To return to the previous
F1: DVD mode menu of Sony TV, press TV
F2: VHS mode (3) and then press
RETURN/EXIT O.
P BD/DVD TOP Press to display the menu or
MENU on-screen guide of the DVD U DISPLAY Press to select information
or Blu-ray disc on the TV displayed on the display
screen. Then, use V/v/B/b window or TV screen of the
and to perform menu VCR, VCD player, LD player,
operations. DVD player, CD player, MD
BD/DVD MENU Press to display the menu of deck, Blu-ray disc player,
PSX, satellite tuner, DVD/
the DVD or Blu-ray disc on
the TV screen. Then, use VHS COMBO, or DVD/HDD
COMBO.
V/v/B/b and to perform
menu operations. To select information of Sony
TV, press TV (C) and then
TV INPUT Press TV (C) and then press DISPLAY.
press TV INPUT to select
V INPUT MODE Press AMP (4), then press
the input signal (TV input or
INPUT MODE to select the
video input).
input mode when the same
WIDE Press TV (C) and then components are connected to
press WIDE to select the both digital and analog jacks
wide picture mode. (page 85).
Q TV VOL +/ Press TV (C) and then W AUTO CAL Press to activate the Digital
press TV VOL +/ to adjust Cinema Auto Calibration
the TV volume level. function.
MASTER Press to adjust the volume X 2CH/ Press to select sound field or
VOL +/ level of all speakers at the A.DIRECT to switch the audio of the
same time. selected input to analog signal
without any adjustment (page
65).
14GB
Name Function
Y SHIFT Press to light up the buttons. It
changes the remote button
function to activate the
buttons with pink printing.
Z THEATRE Press to turn the Theatre mode
on and off when connecting
the receiver to products
featuring BRAVIA Sync.
wj RM SET UP Press to set up the remote.
a) The
number 5/SAT, TV CH +/PRESET + and N
buttons have tactile dots. Use the tactile dots as
references when operating the receiver.
b) This button is also available for DIGITAL MEDIA
Notes
Some functions explained in this section may not
work depending on the model.
The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
15GB
Getting Started
16GB
2: Connecting the speakers
Getting Started
Before connecting the cords, be sure to disconnect the AC power cord (mains lead).
C E D
B B
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
TV DIGITAL (ASSIGNABLE)
MPORT
DC5V
0.7A MAX SAT BD DVD
IN IN IN IN
SURROUND BACK/
AUDIO AUDIO AUDIO
MONITOR BI-AMP/
IN OUT IN FRONT B
FRONT A
AUDIO R L R L
OUT
B
A B
H G F B A
10 mm
continued
17GB
a)
If you connect only one surround back speaker,
connect it to the SPEAKERS SURROUND
BACK/BI-AMP/FRONT B L terminals.
b)
If you are not using surround back speaker, and
you have an additional front speaker system,
connect the additional front speaker system to the
SPEAKERS SURROUND BACK/BI-AMP/
FRONT B terminals. Set SB ASSIGN to
SPK B in the SPEAKER menu (page 51).
You can select the front speaker system you want
to use with SPEAKERS on the front panel
(page 32).
c)
If you are not using surround back speakers, you
can connect the front speakers to the SPEAKERS
SURROUND BACK/BI-AMP/FRONT B
terminals using a bi-amplifier connection
(page 91).
Set SB ASSIGN to BI-AMP in the SPEAKER
menu (page 51).
d) When you connect a subwoofer with an auto
Note
Before connecting the AC power cord (mains lead),
make sure that metalic wires of the speaker cords are
not touching each other between the SPEAKERS
terminals.
18GB
Selecting a speaker pattern
Getting Started
After you have install and connect your speaker, be sure to select the speaker pattern from
SPEAKER menu (page 46).
Select the speaker pattern according to your speaker setting. For details of each parameter, see the
table as follows.
Speaker connected
Front Center Surround Surround Surround Subwoofer
left/right left/right back left back right
Speaker pattern
3/4.1 a a a a a a
3/4 a a a a a
3/3.1 a a a a a
3/3 a a a a
2/4.1 a a a a a
2/4 a a a a
3/2.1 a a a a
3/2 a a a
2/3.1 a a a a
2/3 a a a
2/2.1 a a a
2/2 a a
3/0.1 a a a
3/0 a a
2/0.1 a a
2/0 a
19GB
3: Connecting the TV
You can watch the selected input image when
you connect the HDMI OUT or MONITOR
OUT jack to a TV.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Before connecting cords, be sure to disconnect
the AC power cord.
TV
A B C D E
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
20GB
Notes
Be sure to turn on the receiver when the video and
audio signals of a playback component are being
Getting Started
output to a TV via the receiver. Unless the power is
turned on, neither video nor audio signals will be
transmitted.
Connect image display components such as a TV
monitor or a projector to the HDMI OUT or
MONITOR OUT jack on the receiver. You may
not be able to record, even if you connect recording
components.
Depending on the status of the connection between
the TV and the antenna (aerial), the image on the
TV screen may be distorted. In this case, place the
antenna (aerial) farther away from the receiver.
When connecting optical digital cords, insert the
plugs straight in until they click into place.
Do not bend or tie optical digital cords.
Tips
To output the sound of the TV from the speakers
connected to the receiver, be sure to
connect the audio output jacks of the TV to the
TV IN jacks of the receiver.
turn off the TVs volume or activate the TVs
muting function.
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
21GB
4a: Connecting the audio components
Connecting a Super Audio CD/CD
player or CD recorder
The following illustration shows how to
connect a Super Audio CD player, CD player
or CD recorder. Before connecting cords, be
sure to disconnect the AC power cord.
After connecting your audio component,
proceed to 4b: Connecting the video
components (page 23).
Super Audio
CD player/
CD player/
CD recorder
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
22GB
4b: Connecting the video components
Getting Started
How to connect your Video input/output jack to be
components connected
This section describes how to connect your The image quality depends on the connecting
video components to this receiver. Before you jack. See the illustration that follows. Select
begin, see Component to be connected the connection according to the jacks on your
below for the pages which describe how to components.
connect each component.
After connecting all your components,
Y
proceed to 5: Connecting the antennas HDMI
VIDEO
PR/CR
COMPONENT VIDEO
Component to be connected
Digital Analog
Component Page
TV 20
With HDMI jack 24
High quality image
DVD player 26
Notes
Blu-ray disc player 27
Before connecting cords, be sure to disconnect the
Satellite tuner/Set-top box 28 AC power cord.
VCR, DVD recorder 29 Be sure to turn on the receiver when the video and
audio signals of a playback component are being
Camcorder, video game, etc. 29 output to a TV via the receiver. Unless the power is
turned on, neither video nor audio signals will be
If you want to connect several transmitted.
digital components, but cannot
find an unused input
See Enjoying the sound/images from other
inputs (page 85).
23GB
You can also rename the HDMI input so that it can
Connecting components with be displayed on the receivers display. For details,
HDMI jacks see Naming inputs (page 41).
A A A
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
C B A
Audio/video
Audio signals signals
TV, etc.
24GB
HDMI features When you want to listen to the sound from
A digital audio signals transmitted by HDMI the TV speaker, set AUDIO OUT to
can be output from the speakers connected to TV+AMP in the HDMI menu (page 56). If
Getting Started
the receiver. This signal supports Dolby you cannot play back multi channel
Digital, DTS, and Linear PCM. software, set to AMP. However, the sound
This receiver can receive multi channel will not output from the TV speaker.
Linear PCM (up to 8 channels) with a DSD signals of Super Audio CD are not
sampling frequency of 192 kHz or less with input and output.
an HDMI connection. The multi/stereo area audio signals of a
This receiver supports High Bitrate Audio Super Audio CD are not output.
(DTS-HD Master Audio, Dolby TrueHD) Audio signals (sampling frequency, bit
and HDMI (Deep Color, x.v. Color). length, etc.) transmitted from an HDMI jack
This receiver supports the Control for HDMI may be suppressed by the connected
function. For details, see BRAVIA Sync component. Check the setup of the
Features (page 72). connected component if the image is poor or
HDMI 3 input has a better sound quality. the sound does not come out of a component
When you need a higher sound quality, connected via the HDMI cable.
connect your component to the HDMI IN 3 Sound may be interrupted when the
(for AUDIO) jack and select HDMI 3 as sampling frequency or the number of
input. channels of audio output signals from the
playback component is switched.
Notes on connecting cables When the connected component is not
compatible with copyright protection
We recommend that you use a Sony HDMI
technology (HDCP), the image and/or the
cable.
sound from the HDMI OUT jack may be
We recommend that you use an HDMI cable
distorted or may not be output.
with the HDMI logo (made by Sony) for the
In this case, check the specification of the
HDMI jack corresponding to high speed (an
connected component.
HDMI version1.3, category 2 cable) when
You can enjoy High Bitrate Audio (DTS-HD
you view images or listen to sound during a
Master Audio, Dolby TrueHD), multi-
Deep Color transmission or when you watch
channel Linear PCM only with an HDMI
a video image of 1080p or higher.
connection.
We do not recommend using an HDMI-DVI
Set the image resolution of the player to
conversion cable. When you connect an
more than 720p/1080i to enjoy High Bitrate
HDMI-DVI conversion cable to a DVI-D
Audio (DTS-HD Master Audio, Dolby
component, the sound and/or the image may
TrueHD).
not be output. Connect other audio cords or
The image resolution of player may need
digital connecting cords, then set
certain settings be made before you can
A. ASSIGN in AUDIO menu (page 55)
enjoy multi channel Linear PCM. Refer to
when the sound is not output correctly.
the operating instructions of the player.
Not every HDMI component supports all
Notes on HDMI connections functions that are defined by the specified
An audio signal input to the HDMI IN jack HDMI version. For example, components
is output from the SPEAKERS jacks and that support HDMI, version 1.3, may not
HDMI OUT jack. It is not output from any support Deep Color.
other audio jacks. Refer to the operating instructions of each
Video signals input to the HDMI IN jack can connected component for details.
only be output from the HDMI OUT jack.
The video input signals cannot be output
from the VIDEO OUT jacks or MONITOR
OUT jacks.
25GB
The initial setting of the COMPONENT VIDEO
Connecting a DVD player IN 2 jacks are DVD player. If you want to connect
your DVD player to the COMPONENT VIDEO IN
The following illustration shows how to 1 or IN 3 jacks, set V. ASSIGN in the VIDEO
connect a DVD player. menu (page 56).
It is not necessary to connect all the cords. When connecting optical digital cords, insert the
Connect audio and video cords according to plugs straight in until they click into place.
the jacks of your components. Do not bend or tie optical digital cords.
To input multi channel digital audio from the DVD
Notes player, set the digital audio output setting on the
Be sure to change the factory setting of the DVD DVD player. Refer to the operating instructions
input button on the remote so that you can use the supplied with the DVD player.
button to control your DVD player. For details, see
Programming the remote (page 95). Tip
You can also rename the DVD input so that it can All the digital audio jacks are compatible with
be displayed on the receivers display. For details, 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
see Naming inputs (page 41). frequencies.
DVD player
A B C
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
26GB
When connecting optical digital cords, insert the
Connecting a Blu-ray disc player plugs straight in until they click into place.
Do not bend or tie optical digital cords.
The following illustration shows how to
Getting Started
To input multi channel digital audio from the Blu-
connect a Blu-ray disc player. ray disc player, set the digital audio output setting
It is not necessary to connect all the cords. on the Blu-ray disc player. Refer to the operating
Connect audio and video cords according to instructions supplied with the Blu-ray disc player.
the jacks of your components.
Tip
Notes All the digital audio jacks are compatible with
The initial setting of the COMPONENT VIDEO 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
IN 1 jacks are Blu-ray disc player. If you want to frequencies.
connect your Blu-ray disc player to the
COMPONENT VIDEO IN 2 or IN 3 jacks, set
V. ASSIGN in the VIDEO menu (page 56).
A B C D E
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
27GB
Notes
Connecting a satellite tuner/ The initial setting of the COMPONENT VIDEO
set-top box IN 3 jacks are satellite tuner or set-top box. If you
want to connect your satellite tuner or set-top box
The following illustration shows how to to the COMPONENT VIDEO IN 1 or IN 2 jacks,
connect a satellite tuner or set-top box. set V. ASSIGN in the VIDEO menu (page 56).
It is not necessary to connect all the cords. When connecting optical digital cords, insert the
Connect audio and video cords according to plugs straight in until they click into place.
the jacks of your components. Do not bend or tie optical digital cords.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
A B C D
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
28GB
Notes
Connecting components with Be sure to change the factory setting of the VIDEO
analog video and audio jack 1 input button on the remote so that you can use the
Getting Started
button to control your DVD recorder. For details,
The following illustration shows how to see Programming the remote (page 95).
connect a component which has analog jacks You can also rename the VIDEO 1 input so that it
such as a VCR, DVD recorder, etc. can be displayed on the receivers display. For
It is not necessary to connect all the cords. details, see Naming inputs (page 41).
Connect audio and video cords according to
the jacks of your components.
A B
ANTENNA HDMI
AM
IN 4 IN 3 (for AUDIO) IN 2 IN 1 OUT
EZW-T100
ASSIGNABLE (INPUT ONLY)
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
Camcorder/
video game
C
29GB
5: Connecting the 6: Preparing the receiver
antennas (aerials) and the remote
Connect the supplied AM loop antenna
(aerial) and FM wire antenna (aerial). Connecting the AC power cord
Before connecting antennas (aerials), be sure (mains lead)
to disconnect the power cord.
Connect the AC power cord (mains lead) to a
FM wire antenna (aerial) (supplied) wall outlet.
AM loop antenna (aerial) AC power cord (mains lead)
(supplied)
OUT
ANTENNA
AM
EZW-T100
MONITOR
TV DIGI
IN 3 IN 2 IN 1
OUT DMPORT L
DC5V
Y 0.7A MAX SAT
IN IN
OPTICAL OPTIC
PB/
CB
VIDEO VIDEO VIDEO VIDEO VIDEO
IN IN OUT IN OUT L
PR/
CR
SURROUND
COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) AUDIO AUDIO AUDIO AUDIO
MONITOR BI-AMP
OUT IN IN IN IN OUT IN FRONT
L
AUDIO R
OUT
Notes
To prevent noise pickup, keep the AM loop
antenna (aerial) away from the receiver and other
components.
Be sure to fully extend the FM wire antenna
(aerial).
After connecting the FM wire antenna (aerial),
keep it as horizontal as possible.
30GB
Performing initial setup Inserting batteries into the
operations remote
Getting Started
Before using the receiver for the first time, Insert two R6 (size-AA) batteries in the
initialize the receiver by performing the RM-AAP044 Remote Commander.
following procedure. This procedure can also Observe the correct polarity when installing
be used to return settings you have made to batteries.
their factory defaults.
Be sure to use the buttons on the receiver for
this operation.
?/1
MASTER VOLUME
?/1
TONE INPUT SELECTOR
SPEAKERS
MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
Notes
Do not leave the remote in an extremely hot or
MEMORY/ENTER humid place.
Do not use a new battery with old ones.
31GB
7: Selecting the speaker 8: Calibrating the
system appropriate settings
You can select the front speakers you want to automatically
drive. (AUTO CALIBRATION)
Be sure to use the buttons on the receiver for
this operation. This receiver is equipped with DCAC (Digital
SPEAKERS
Cinema Auto Calibration) Technology which
allows you to perform automatic calibration as
follows:
Check the connection between each speaker
MASTER VOLUME
?/1
SPEAKERS
32GB
Before you perform Auto
MASTER VOLUME
?/1
TONE INPUT SELECTOR
SPEAKERS
Optimizer microphone
Calibration
MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
Getting Started
Before you perform the Auto Calibration, set AUTO CAL MIC
continued
33GB
Note Press AUTO CAL.
Depending on the characteristics of the subwoofer Measurement starts in 5 seconds. A count
you are using, the setup distance value may be
down is displayed.
further away from the actual position.
The measurement process will take
approximately 30 seconds to complete.
Performing Auto Calibration The table below shows the display when
measurement starts.
Measurement for Display
?/1
THEATRE RM SET UP AV ?/1 ?/1 Speaker existence TONE
switch
SYSTEM STANDBY
SHIFT TV AMP Speaker gain, distance, frequency T.S.P.
AMP
response
1 2 3
VIDEO 1 VIDEO 2 BD Subwoofer gain and distance WOOFER
4 5 6
DVD SAT TV
Tips
7 8 9 Input
SA-CD/ TUNER DMPORT buttons Operations other than turning the receiver on or off
CD
-/-- 0/10 ENT/MEM are deactivated during the measurement.
HDMI 1 HDMI 2 HDMI 3
The measurements may not be performed correctly
CLEAR/>10
HDMI 4
or Auto Calibration cannot be performed when
2CH/
special speakers, such as dipole speakers are used.
A.DIRECT A.F.D. MOVIE MUSIC
INPUT NIGHT
AUTO AUTO CAL MODE SLEEP MODE
MUTING MASTER
VOL +/
34GB
Confirming/saving the
3 Select SAVE EXIT in step 2 to
save the measurement result.
measurement results COMPLETE appears on the display
Getting Started
1 Confirm the measurement and the settings are registered as selected
position number.
result.
When the measurement ends, a beep 4 Press V/v repeatedly to select
sounds and the measurement result CAL TYPE, then press .
appears on the display.
Calibration Explanation
Measurement Display Explanation type
result
FULL FLAT Makes the measurement of
When the SAVE EXIT Proceed to step frequency from each
measurement 2. speaker flat.
process
completes ENGINEER Sets the frequency
properly characteristics to a set that
matches that of the Sony
When the E- See When listening room standard.
measurement xxx:xx error codes
process fails appear (page FRONT REF Adjusts the characteristics
36). of all speakers to match the
characteristics of the front
2 Press AMP and then press V/v speaker.
repeatedly to select the item. OFF Sets the Auto Calibration
equalizer level to off.
Then, press .
Tip
Item Explanation
The size of a speaker (LARGE/SMALL) is
EXIT Exits the setting process determined by the low frequency
without saving the characteristics.
measurement results. The measurement results may vary, depending
LEVEL INFO Displays the measurement on the position of the optimizer microphone
result for speaker level. and speakers, and the shape of the room. It is
recommended that you follow the
DIST. INFO Displays the measurement
result for speaker distance. measurement results. However, you can
change those settings in the SPEAKER menu
PHASE INFO Displays the phase of each (page 50). Save the measurement results first,
speaker (in phase/out of then try to change the settings if you want.
phase). See When you
select PHASE INFO
(page 36).
WARN CHECK Displays warning
concerning the
measurement results. See
When you select WARN
CHECK (page 37).
SAVE EXIT Saves the measurement
results and exits the setting
process.
RETRY Performs the Auto
Calibration again.
continued
35GB
When error codes appear To perform Auto Calibration
Check the problem of the error and perform again
Auto Calibration again. 1 Press .
Display Explanation
2 Press V/v to select RETRY? YES,
E - xxx*1 : 31 SPEAKERS is set to OFF. Set it then press .
to others (page 32) and perform
the measurement again.
E - xxx*1 : 32 None of the speakers were
When you select PHASE INFO
detected. Make sure that the You can check the phase of each speaker (in
optimizer microphone is phase/out of phase).
connected properly and perform
the measurement again. If the Press V/v repeatedly to select a
optimizer microphone is
connected properly but the error speaker, then press to return to
code appears, the optimizer step 2 of Confirming/saving the
microphone cable may be measurement results (page 35).
damaged or improperly
connected. Display Explanation
E - xxx*1 : 33 None of the front speakers are xxx *2 : IN The speaker is in phase.
connected or only one front
speaker is connected. xxx *2 : OUT The speaker is out of phase. The
The optimizer microphone is + and terminals of the
not connected. speaker may be connected the
Either the left or right other way around. However,
depending on the speakers,
surround speakers is not
xxx : OUT appears on the
connected.
display even though the
Surround back speakers are
speakers are connected
connected even though properly. This is because of the
surround speakers are not speakers specifications. In this
connected. Connect the case, you can continue to use the
surround speaker(s) to the receiver.
SURROUND terminals.
*2 xxx represent a speaker channel
The surround back speaker is
connected only to the FL Front left
SPEAKERS SURROUND FR Front right
BACK/BI-AMP/FRONT B R CNT Center
terminals. When you connect SL Surround left
only one surround back SR Surround right
speaker, connect it to the SB Surround back
SPEAKERS SURROUND SBL Surround back left
BACK/BI-AMP/FRONT B L SBR Surround back right
terminals. SW Subwoofer
*1
xxx represent a speaker channel
F Front
S Surround
SB Surround back
36GB
When you select WARN Tip
CHECK Depending on the position of the subwoofer, the
If a warning on the measurement result is measurement results for polarity may vary.
Getting Started
However, there will be no problems even if you
present, detailed information is displayed.
continue to use the receiver with that value.
Press to return to step 2 of
Confirming/saving the After you have finished
measurement results (page 35). Disconnect the optimizer microphone from the
receiver.
Display Explanation
Note
W - xxx *3 : 40 The measurement has
If you have reposition your speaker, we recommend
completed. However, the noise
level is high. You may be able that you perform Auto Calibration again to enjoy the
to perform the measurement surround sound.
properly if you try it again,
even though the measurement
cannot be performed in all AUTO CAL menu parameters
environments. Try to perform
the measurement in a quiet You can use the AUTO CAL menu to make
environment. various adjustments for Auto Calibration
W - xxx *3 : 41 The sound input from the settings and to name inputs.
optimizer microphone is Select AUTO CAL in the amplifier menus.
outside the acceptable range. It For details on adjusting the parameters, see
is louder than the loudest sound
that can be measured. Try to Navigating through menus (page 44) and
perform the measurement Overview of the menus (page 45).
when the environment is quiet
enough to allow proper x A.CAL START (Auto Calibration)
measurement.
W - xxx *3 : 42 The volume of the receiver is x CAL TYPE (Calibration type)*
out of the acceptable range. Try Lets you select the Auto Calibration type for
to perform the measurement each seating position. For details, see step 4 of
when the environment is quiet
enough to allow proper
Confirming/saving the measurement results
measurement. (page 35).
W - xxx *3 : 43 The distance and position of a * You can select this parameter only when you have
subwoofer cannot be detected. performed the Auto Calibration and saved the
This may be caused by noise. settings.
Try to perform the
measurement in a quiet
environment.
xPOSITION (Position)
You can register three patterns as position 1, 2,
NO WARN There is no warning 3, depending on the seating positions, listening
information.
environment, and measurement conditions.
*3 If you do not select the position number, the
xxx represent a speaker channel
FL Front left Auto Calibration result will automatically save
FR Front right as POS. 1 (initial setting).
CNT Center
SL Surround left
SR Surround right
SBL Surround back left
SBR Surround back right
SW Subwoofer
continued
37GB
To register more than one set of To exit the menu
settings for the listening Press MENU/HOME or AMP MENU.
environment
You can select the seating position you want x NAME IN (Naming inputs)
and register the measurement results of the You can rename the position name.
Auto Calibration for that seating position.
1 Press AMP MENU. To name the position
2 Press V/v repeatedly to select AUTO 1 Select the position (POS. 1, 2, 3) for
CAL. which you want to name.
38GB
4 Press V/v repeatedly to select
9: Adjusting the speaker the test tone type and the
speaker you want to adjust.
Getting Started
levels and balance You can select FIX xxx or
AUTO xxx. For details, see TEST TONE
(TEST TONE) (Test tone) (page 49).
4
DVD
5
SAT
6
TV
5 Repeat steps 1 to 4 to select
7 8 9 Input OFF.
SA-CD/
CD TUNER DMPORT buttons You can also press any input buttons.
-/-- 0/10 ENT/MEM
HDMI 1 HDMI 2 HDMI 3 The test tone turns off.
CLEAR/>10
HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
When a test tone is not output
INPUT NIGHT from the speakers
AUTO CAL MODE SLEEP MODE
The speaker cords may not be connected
DISPLAY AMP MENU AMP securely.
MENU
The speaker cords may have the short-circuit
, problem.
V/v/B/b
O
RETURN/ HOME TOOLS/
When a test tone is output from
EXIT
MENU
OPTIONS
a different speaker than the
speaker indicator showed in the
. < < >
TUNING TUNING +
front panel display.
m M The speaker pattern to the connected speaker
DISC SKIP D.TUNING
X x is not set up correctly. Make sure the speaker
TV VOL
MASTER VOL
TV CH
PRESET connection and the speaker pattern match.
MUTING
MASTER
VOL +/
BD/DVD
TOP MENU MENU F1 F2
TV INPUT WIDE
39GB
Selected input Components that can
Playback [Display] be played back
VIDEO 1 VCR, etc., connected to the
[VIDEO 1] VIDEO 1 jack
Selecting a component VIDEO 2 Camcorder, video game,
SHIFT TV AMP
[VIDEO 2] etc., connected to the
VIDEO 2/PORTABLE AV
1 2 3 IN jack
VIDEO 1 VIDEO 2 BD
CLEAR/>10
SAT Satellite tuner, set-top box,
HDMI 4 [SAT] etc., connected to SAT jack
2CH/
A.DIRECT A.F.D. MOVIE MUSIC TV TV, etc., connected to TV
INPUT NIGHT [TV] jack
AUTO CAL MODE SLEEP MODE
40GB
To activate the muting function 7 Press V/v to select a character,
Press MUTING on the remote. then press B/b to move the
The muting function will be canceled when cursor to the next position.
you do the following.
Press MUTING again. If you made a mistake
Increase the volume. Press B/b until the character you want to
Turn off the receiver. change flashes, then press V/v to select
Playback
the correct character.
41GB
Listening/Watching a component
Listening to a Super Audio CD/CD
SHIFT
SYSTEM STANDBY
TV
?/1
AMP
2 3
1 2 3
VIDEO 1 VIDEO 2 BD
MASTER VOLUME
4 5 6
DVD SAT TV
7 8 9 ?/1
SA-CD/
CD
-/--
HDMI 1
CLEAR/>10
TUNER
0/10
HDMI 2
DMPORT
ENT/MEM
HDMI 3 3 SPEAKERS
TONE INPUT SELECTOR
5
HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
INPUT NIGHT
AUTO CAL MODE SLEEP MODE MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
DISPLAY AMP MENU
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
O
RETURN/ HOME TOOLS/
EXIT OPTIONS
MENU
TUNING TUNING +
m M
5
MUTING
BD/DVD
TOP MENU MENU F1 F2
TV INPUT WIDE
Notes
The operation is described for a
1 Turn on the Super Audio CD player or CD
Sony Super Audio CD player. player, then place the disc on the tray.
Refer to the operating
instructions supplied with the 2 Turn on the receiver.
Super Audio CD player or CD
player. 3 Press SA-CD/CD.
You can also use INPUT SELECTOR on the receiver to
Tips
select SA-CD/CD/CD-R.
You can select the sound field to
suit the music. See page 62 for
details.
4 Play back the disc.
Recommended sound fields:
Classical: HALL
5 Adjust to a suitable volume.
Jazz: JAZZ
Live concert: CONCERT
6 After you have finished listening to the
You can listen to the sound that
Super Audio CD/CD, eject the disc and turn
was recorded in the 2 channel off the receiver and Super Audio CD player
format from all speakers (multi or CD player.
channel). See page 59 for
details.
42GB
Watching a DVD/Blu-ray Disc
THEATRE RM SET UP AV ?/1
SHIFT
SYSTEM STANDBY
TV
?/1
AMP
2 3
1 2 3
VIDEO 1 VIDEO 2 BD
MASTER VOLUME
4 5 6
3
DVD SAT TV
7 8 9 ?/1
Playback
6
SA-CD/ TUNER DMPORT
CD TONE INPUT SELECTOR
-/-- 0/10 ENT/MEM
HDMI 1 HDMI 2 HDMI 3
SPEAKERS
CLEAR/>10
HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
INPUT NIGHT
AUTO CAL MODE SLEEP MODE MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
DISPLAY AMP MENU
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
O
RETURN/ HOME TOOLS/
EXIT OPTIONS
MENU
TUNING TUNING +
m M
6
MUTING
BD/DVD
TOP MENU MENU F1 F2
TV INPUT WIDE
Notes
Refer to the operating
1 Turn on the TV and DVD player/Blu-ray disc
instructions supplied with the player.
TV and DVD player/Blu-ray
disc player. 2 Turn on the receiver.
Check the following if you
cannot listen to multi channel 3 Press DVD to watch a DVD or press BD to
sound. watch a Blu-ray disc.
Be sure this receiver is You can also use INPUT SELECTOR on the receiver to
connected to the DVD player/ select DVD or BD.
Blu-ray disc player via a
Be sure to change the factory setting of the DVD input
digital connection.
Be sure the digital audio
button on the remote so that you can use the button to
output of the DVD player/ control your DVD player. For details, see Programming
Blu-ray disc player is set up the remote (page 95).
properly.
4 Switch the input of the TV so that an image
Tips of the DVD/Blu-ray disc is displayed.
Select the audio format of the
disc to be played back, if
necessary.
5 Play back the disc.
You can select the sound field to
suit the movie or music. See
6 Adjust to a suitable volume.
page 59 for details.
Recommended sound fields:
7 After you have finished watching the DVD/
Blu-ray disc, eject the disc and turn off the
Movie: C.ST.EX
Music: CONCERT receiver, TV and DVD player/Blu-ray disc
player.
43GB
To return to the previous
Amplifier Operations display
Press B or RETURN/EXIT O.
INPUT NIGHT
AUTO CAL MODE SLEEP MODE
RETURN/
O
EXIT O RETURN/ HOME TOOLS/
EXIT OPTIONS MENU/
MENU
HOME
. < < >
44GB
Overview of the menus
The following options are available in each
menu. For details on navigating through
menus, see page 44.
Menu Parameters Settings Initial
[Display] [Display] setting
AUTO CAL Auto calibration
[AUTO CAL] [A.CAL START]
(page 37)
Calibration typea) FULL FLAT, ENGINEER FULL FLAT
Amplifier Operations
[CAL TYPE] FRONT REF, OFF
Positiona) POS. 1, POS. 2, POS. 3 POS. 1
[POSITION]
Naming inputsa) For details, see To name the
[NAME IN] position (page 38).
LEVEL Test tonea)c) OFF, FIX xxxb), AUTO xxxb) OFF
[LEVEL] [TEST TONE]
(page 49)
Phase noisea)c) OFF, FL/SR, SL/FL, SB/SL, SBL/SL, OFF
[P. NOISE] SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, FL/FR, CNT/FR,
FL/CNT
Phase audioa)c) OFF, FL/SR, SL/FL, SB/SL, SBL/SL, OFF
[P. AUDIO] SBR/SBL, SR/SB, SR/SBR, SR/SL,
FR/SR, FR/SL, FL/FR, CNT/FR,
FL/CNT
Front left speaker levelc) FL 10 dB to FL +10 dB 0 dB
[FL LEVEL] (0.5 dB per step)
Front right speaker levelc) FR 10 dB to FR +10 dB 0 dB
[FR LEVEL] (0.5 dB per step)
Center speaker levelc) CNT 20 dB to CNT +10 dB 0 dB
[CNT LEVEL] (0.5 dB per step)
Surround left speaker levelc) SL 20 dB to SL +10 dB 0 dB
[SL LEVEL] (0.5 dB per step)
Surround right speaker levelc) SR 20 dB to SR +10 dB 0 dB
[SR LEVEL] (0.5 dB per step)
Surround back speaker levelc) SB 20 dB to SB +10 dB 0 dB
[SB LEVEL] (0.5 dB per step)
Surround back left speaker levelc) SBL 20 dB to SBL +10 dB 0 dB
[SBL LEVEL] (0.5 dB per step)
Surround back right speaker SBR 20 dB to SBR +10 dB 0 dB
levelc) (0.5 dB per step)
[SBR LEVEL]
Subwoofer levelc) SW 20 dB to SW +10 dB 0 dB
[SW LEVEL] (0.5 dB per step)
Dynamic range compressora) COMP. MAX, COMP. STD, COMP. AUTO
[D. RANGE] COMP. AUTO, COMP. OFF
continued
45GB
Menu Parameters Settings Initial
[Display] [Display] setting
SPEAKER Speaker patterna) 3/4.1, 3/4, 3/3.1, 3/3, 2/4.1, 2/4, 3/2.1, 3/4.1
[SPEAKER] [SP PATTERN] 3/2, 2/3.1, 2/3, 2/2.1, 2/2, 3/0.1, 3/0,
(page 50) 2/0.1, 2/0
Front speakersa) LARGE, SMALL LARGE
[FRT SP]
Center speakera) LARGE, SMALL LARGE
[CNT SP]
Surround speakersa) LARGE, SMALL LARGE
[SUR SP]
Surround back speaker assigna)d) SPK B, BI-AMP, OFF OFF
[SB ASSIGN]
Front left speaker distancea)c) FL 1.00 m to FL 10.00 m FL 3.00 m
[FL DIST.] (0.01 m step)
Front right speaker distancea)c) FR 1.00 m to FR 10.00 m FR 3.00 m
[FR DIST.] (0.01 m step)
Center speaker distancea)c) CNT 1.00 m to CNT 10.00 m CNT 3.00 m
[CNT DIST.] (0.01 m step)
Surround left speaker distancea)c) SL 1.00 m to SL 10.00 m SL 3.00 m
[SL DIST.] (0.01 m step)
Surround right speaker SR 1.00 m to SR 10.00 m SR 3.00 m
distancea)c) (0.01 m step)
[SR DIST.]
Surround back speaker SB 1.00 m to SB 10.00 m SB 3.00 m
distancea)c) (0.01 m step)
[SB DIST.]
Surround back left speaker SBL 1.00 m to SBL 10.00 m SBL 3.00 m
distancea)c) (0.01 m step)
[SBL DIST.]
Surround back right speaker SBR 1.00 m to SBR 10.00 m SBR 3.00 m
distancea)c) (0.01 m step)
[SBR DIST.]
Subwoofer distancea)c) SW 1.00 m to SW 10.00 m SW 3.00 m
[SW DIST.] (0.01 m step)
Distance unita) FEET, METER METER
[DIST. UNIT]
Front speaker crossover CROSS 40 Hz to CROSS 200 Hz CROSS 120 Hz
frequencya)e) (10 Hz step)
[FRT CROSS]
Center speaker crossover CROSS 40 Hz to CROSS 200 Hz CROSS 120 Hz
frequencya)e) (10 Hz step)
[CNT CROSS]
Surround speaker crossover CROSS 40 Hz to CROSS 200 Hz CROSS 120 Hz
frequencya)e) (10 Hz step)
[SUR CROSS]
46GB
Menu Parameters Settings Initial
[Display] [Display] setting
SURROUND Sound field selection For details, see Enjoying Surround A.F.D. AUTO
[SURROUND] [S.F. SELECT] Sound (page 59).
(page 53)
Enhanced surround mode PLIIf), PLIIxf), NEO6 CIN, NEO6 PLIIx
[E.SUR MODE] MUS, NEURAL-THX
Effect levela) EFCT. 50%, EFCT. 80%, EFCT. 100%
[EFFECT] EFCT. 100%, EFCT. 150%
EQ Front speakers bass level BASS 10 dB to BASS +10 dB BASS 0 dB
[EQ] [BASS] (1dB per step)
Amplifier Operations
(page 54)
Front speakers treble level TREBLE 10 dB to TREBLE +10 dB TREBLE 0 dB
[TREBLE] (1dB per step)
TUNER FM station receiving modea) STEREO, MONO STEREO
[TUNER] [FM MODE]
(page 54)
Naming preset stationsa) For details, see Naming preset
[NAME IN] stations (page 70).
AUDIO Synchronizes audio with video 0 ms to 300 ms 0 ms
[AUDIO] outputa) (10 ms per step)
(page 55) [A/V SYNC]
Digital broadcast language MAIN/SUB, MAIN, SUB MAIN
selectiona)
[DUAL MONO]
Digital audio input decoding DEC. AUTO, DEC. PCM DEC. AUTO
prioritya)
[DEC. PRIO.]
Digital audio input assignmenta) For details, see Enjoying the sound/
[A. ASSIGN] images from other inputs (page 85).
VIDEO Video input assignmenta) For details, see Enjoying the sound/
[VIDEO] [V. ASSIGN] images from other inputs (page 85).
(page 56)
continued
47GB
Menu Parameters Settings Initial
[Display] [Display] setting
HDMI Control for HDMIa) CTRL ON, CTRL OFF CTRL OFF
[HDMI] [CTRL:HDMI]
(page 56)
Setting HDMI audio inputa) AMP, TV+AMP AMP
[AUDIO OUT]
Subwoofer level for HDMIa)g) SW AUTO, SW 0 dB, SW +10 dB SW AUTO
[SW LEVEL]
SYSTEM Naming inputs For details, see Naming inputs
[SYSTEM] [NAME IN] (page 41).
(page 57)
Brightness of the displaya) 70% DOWN, 40% DOWN, 0% DOWN
[DIMMER] 0% DOWN
S-AIR S-AIR IDa)h) ID: A, ID: B, ID: C ID: A
[S-AIR] [S-AIR ID]
(page 58)
Pairinga)h) START, CONDITION START
[PAIRING]
S-AIR modea)h) PARTY, SEPARATE PARTY
[S-AIR MODE]
RF Changea)h) RF AUTO, RF ON, RF OFF RF AUTO
[RF CHANGE]
S-AIR Standbya)h) STBY ON, STBY OFF STBY OFF
[S-AIR STBY]
a) For details, see the page in the parentheses.
b)
xxx represent a speaker channel (FL, FR, CNT, SL, SR, SB, SBL, SBR, SW).
c) Depends on the speaker pattern setting, some parameters may not be available.
d) You can only select this parameter if SP PATTERN is not set to a setting with surround back speakers (page
50).
e) You cannot select this setting if your speaker is set to LARGE.
f) Depends on the speaker pattern setting, some settings may not be available.
g)
This parameter is only available when HDMI input signals is detected.
h) This parameter is only available if the S-AIR transmitter (not supplied) is inserted to the EZW-T100 slot on
the receiver.
48GB
x P. AUDIO (Phase Audio)
Adjusting the level OFF
FL/SR, SL/FL, SB/SL, SBL/SL, SBR/SBL,
(LEVEL menu) SR/SB, SR/SBR, SR/SL, FR/SR, FR/SL,
FL/FR, CNT/FR, FL/CNT
You can use the LEVEL menu to adjust the Lets you output front 2 channel source sound
balance and level of each speaker. These (instead of the test tone) sequentially from
settings are applied to all sound fields. adjacent speakers.
Select LEVEL in the amplifier menus. For Some items may not be displayed,
details on adjusting the parameters, see depending on the setting of the speaker
Navigating through menus (page 44) and pattern.
Amplifier Operations
Overview of the menus (page 45).
x FL LEVEL (Front left speaker
LEVEL menu parameters level)
continued
49GB
x D. RANGE (Dynamic range
compressor)
Lets you compress the dynamic range of the
Settings for the speakers
sound track. This may be useful when you (SPEAKER menu)
want to watch movies at low volumes late at
night. Dynamic range compression is possible You can use the SPEAKER menu to set the
with Dolby Digital sources only. size and distance of the speakers connected to
COMP. MAX this receiver.
The dynamic range is compressed Select SPEAKER in the amplifier menus.
dramatically. For details on adjusting the parameters, see
COMP. STD Navigating through menus (page 44) and
The dynamic range is compressed as Overview of the menus (page 45).
intended by the recording engineer.
COMP. AUTO SPEAKER menu parameters
The dynamic range is compressed
automatically. x SP PATTERN (Speaker pattern)
COMP. OFF Lets you set the number of the speakers
The dynamic range is not compressed. connected to this receiver. It should be
synchronize with the subwoofer, front
Tip
speakers, center speaker, surround speakers
Dynamic range compressor lets you compress the
and surround back speakers settings. For
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby details, see Selecting a speaker pattern (page
Digital signal. 19).
COMP. STD is the standard setting, but it only
enacts light compression. Therefore, we recommend x FRT SP (Front speakers)
using the COMP. MAX setting. This greatly LARGE
compresses the dynamic range and lets you view If you connect large speakers that will
movies late at night at low volumes. Unlike analog effectively reproduce bass frequencies,
limiters, the levels are predetermined and provide a select LARGE. Normally, select
very natural compression. LARGE. However, if you have selected a
speaker pattern without subwoofer, the front
speakers are automatically set to LARGE.
SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select SMALL to activate
the bass redirection circuitry and output the
front channel bass frequencies from the
subwoofer. When the front speakers are set
to SMALL, the center and surround
speakers are also automatically set to
SMALL.
50GB
x CNT SP (Center speaker) Tip
LARGE The LARGE and SMALL settings for each
If you connect a large speaker that will speaker determine whether the internal sound
effectively reproduce bass frequencies, processor will cut the bass signal from that channel.
select LARGE. Normally, select When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
LARGE. However, if the front speakers
frequencies to the subwoofer or other LARGE
are set to SMALL, you cannot set the speakers.
center speaker to LARGE. However, since bass sounds have a certain amount of
SMALL directionality, it is best not to cut them, if possible.
If the sound is distorted, or you feel a lack of Therefore, even when using small speakers, you can
surround effects when using multi channel set them to LARGE if you want to output the bass
Amplifier Operations
surround sound, select SMALL to activate frequencies from that speaker. On the other hand, if
the bass redirection circuitry and output the you are using a large speaker, but prefer not to have
center channel bass frequencies from the bass frequencies output from that speaker, set it to
front speakers (if set to LARGE) or SMALL.
If the overall sound level is lower than you prefer, set
subwoofer.
all speakers to LARGE. If there is not enough
bass, you can use the equalizer to boost the bass
x SUR SP (Surround speakers) levels. For details, see page 54.
The surround back speakers will be set to the
same setting. x SB ASSIGN (Surround back
LARGE speaker assign)
If you connect large speakers that will SPK B
effectively reproduce bass frequencies, If you connect an additional front speaker
select LARGE. Normally, select system to the SPEAKERS SURROUND
LARGE. However, if the front speakers BACK/BI-AMP/FRONT B terminals, select
are set to SMALL, you cannot set the SPK B.
surround speakers to LARGE. BI-AMP
SMALL If you connect front speakers to the
If the sound is distorted, or you feel a lack of SPEAKERS SURROUND BACK/BI-AMP/
surround effects when using multi channel FRONT B terminals using a bi-amplifier
surround sound, select SMALL to activate connection, select BI-AMP.
the bass redirection circuitry and output the OFF
surround channel bass frequencies from the If you connect surround back speakers to the
subwoofer or other speaker that is set to SPEAKERS SURROUND BACK/BI-AMP/
LARGE. FRONT B terminals, select OFF.
Note
Set SB ASSIGN to OFF, then connect the
surround back speakers to this receiver when you
want to change the connection from a bi-amplifier
connection or speakers front B connection to a
surround back speakers connection. Re-set up the
speakers after you connect the surround back
speakers. See 8: Calibrating the appropriate
settings automatically (AUTO CALIBRATION)
(page 32).
continued
51GB
x FL DIST. (Front left speaker x SB DIST. (Surround back
distance) speaker distance)
Tip
The distance between the center speaker and the
listening position B cannot be more than 1.5 meters
closer than the one between the listening position
and the front speaker A. Place the speakers so that
the difference in the length of B in the following
diagram is no more than 1.5 meters closer than the
With two surround back speakers length of A.
(The angle B should be the same) Example: Adjust the distance B to 4.5 meters or
more when the distance A is 6 meters.
Also, the distance between the surround speakers/
surround back speakers and the listening position
C cannot be more than 4.5 meters closer than the
distance between the listening position and the front
speakers A. Place the speakers so that the
difference in the length of C in the following
diagram is no more than 4.5 meters closer than the
length of A.
Example: Adjust the distance C to 1.5 meters or
more when the distance A is 6 meters.
This is important because incorrect speaker
placement is not conductive to the enjoyment of
x CNT DIST. (Center speaker
distance) surround sound. Please note that placing the
Lets you set the distance from your listening speakers closer than the required will cause a delay
position to the center speaker. in the output of the sound from that speaker. In other
words, the speaker will sound like it is farther away.
Adjusting these parameter while listening to the
x SL DIST. (Surround left speaker
sound often results in much better surround sound.
distance)
Give it a try!
x SR DIST. (Surround right
speaker distance)
Lets you set the distance from your listening
position to the surround speakers.
52GB
Settings for the surround
sound
(SURROUND menu)
You can use the SURROUND menu to select
the sound field you want for your listening
pleasure.
Select SURROUND in the amplifier menus.
Amplifier Operations
x DIST. UNIT (Distance unit) For details on adjusting the parameters, see
Lets you select the unit of measure for setting Navigating through menus (page 44) and
distances. Overview of the menus (page 45).
FEET
The distance is displayed in feet.
METER SURROUND menu parameters
The distance is displayed in meters.
x S.F. SELECT (Sound field
selection)
x FRT CROSS (Front speaker
Lets you select the sound field you want. For
crossover frequency)
Lets you set the bass crossover frequency of details, see Enjoying Surround Sound (page
the front speakers that have been set to 59).
SMALL in the SPEAKER menu. Note
The receiver lets you apply the last selected sound
x CNT CROSS (Center speaker field to an input whenever it is selected (Sound Field
crossover frequency) Link). For example, if you select HALL for the
Lets you set the bass crossover frequency of DVD input, then change to a different input and then
the center speaker that have been set to return to DVD, HALL will automatically be
SMALL in the SPEAKER menu. applied again.
53GB
Adjusting the equalizer Settings for the tuner
(EQ menu) (TUNER menu)
You can use the EQ menu to adjust the tonal You can use the TUNER menu to set the FM
quality (bass/treble level) of the front station receiving mode and name preset
speakers. stations.
Select EQ in the amplifier menus. For Select TUNER in the amplifier menus. For
details on adjusting the parameters, see details on adjusting the parameters, see
Navigating through menus (page 44) and Navigating through menus (page 44) and
Overview of the menus (page 45). Overview of the menus (page 45).
54GB
x DEC. PRIO. (Digital audio input
decoding priority)
Settings for the audio Lets you specify the input mode for the digital
(AUDIO menu) signal input to the HDMI IN jacks.
DEC. AUTO
You can use the AUDIO menu to make Automatically switches the input mode
settings for the audio to suit your preference. between DTS, Dolby Digital, or PCM.
Select AUDIO in the amplifier menus. For DEC. PCM
details on adjusting the parameters, see PCM signals are output from the connected
Navigating through menus (page 44) and player. To prevent interruption when
Overview of the menus (page 45). playback starts, set to DEC. PCM. When
Amplifier Operations
signals other than PCM signals are received,
set this item to DEC. AUTO.
AUDIO menu parameters
Note
x A/V SYNC (Synchronizes audio Even when DEC. PRIO. is set to DEC. PCM,
with video output) the sound may be interrupted at the very
Lets you delay the output of audio to minimize beginning of the first track depending on the CD
the time gap between audio output and visual being played back.
display. You can adjust from 0 ms to 300 ms
in 10 ms steps. x A. ASSIGN (Digital audio input
assignment)
Notes Lets you assign the digital audio input to other
This parameter is useful when you use a large LCD input source. For details, see Enjoying the
or plasma monitor or a projector.
sound/images from other inputs (page 85).
This parameter is not valid when ANALOG
DIRECT is selected (page 65).
55GB
Settings for the video Settings for the HDMI
(VIDEO menu) (HDMI menu)
You can use the VIDEO menu to assign the You can use the HDMI menu to make various
video input to other input source. adjustments for HDMI settings.
Select VIDEO in the amplifier menus. For Select HDMI in the amplifier menus. For
details on adjusting the parameters, see details on adjusting the parameters, see
Navigating through menus (page 44) and Navigating through menus (page 44) and
Overview of the menus (page 45). Overview of the menus (page 45).
56GB
x SW LEVEL (Subwoofer level for
HDMI)
Lets you set the level of the subwoofer to 0 dB
Settings for the system
or +10 dB when PCM signals are input via an (SYSTEM menu)
HDMI connection. You can set the level for
each HDMI input independently. You can use the SYSTEM menu to name
SW AUTO inputs and change the brightness of the
Automatically sets the level to 0 dB or +10 display.
dB depending on the frequency. Select SYSTEM in the amplifier menus. For
SW 0 dB details on adjusting the parameters, see
SW +10 dB Navigating through menus (page 44) and
Amplifier Operations
Overview of the menus (page 45).
Note
This parameter is only available when HDMI input
signals are detected. SYSTEM menu parameters
x NAME IN (Naming inputs)
Lets you set the name of inputs. For details,
see Naming inputs (page 41).
57GB
Settings for the S-AIR
(S-AIR menu)
For details on S-AIR, see S-AIR Operations
(page 76).
58GB
Enjoying Surround Sound
59GB
Selecting Auto Format Direct
(A.F.D.) mode
The Auto Format Direct (A.F.D.) mode allows
you to listen to higher fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
CLEAR/>10
HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
A.F.D. INPUT NIGHT
AUTO CAL MODE SLEEP MODE
60GB
Selecting enhanced surround
mode
The enhanced surround mode allows you to
listen to higher fidelity sound and select the
decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
A.F.D. INPUT NIGHT
AUTO CAL MODE SLEEP MODE
,
V/v/B/b
continued
61GB
Types of enhanced surround mode
Enhanced surround Multi channel Effect
mode audio after
[Display] decoding
Pro Logic II* 5 channel Performs Dolby Pro Logic II decoding.
[PLII]
Pro Logic IIx* 7 channel Performs Dolby Pro Logic IIx decoding.
[PLIIx]
Neo:6 Cinema 7 channel Performs DTS Neo:6 Cinema mode decoding.
[NEO6 CIN]
Neo:6 Music 7 channel Performs DTS Neo:6 Music mode decoding. This setting is
[NEO6 MUS] ideal for normal stereo sources such as CDs.
Neural-THX 7 channel Next generation of Neural-THX Surround. In addition to
[NEURAL-THX] stereo enhancement processing and pure discrete 5.1
surround sound, now capable of full 360 7.1 surround sound
playback from Neural-THX surround encoded content.
* Depends on the speaker pattern setting, some enhanced surround mode may not be available.
A.F.D. MOVIE
Notes DISPLAY AMP MENU
Tips
You can identify the encoding format of DVD
software, etc., by looking at the logo on the
package.
Dolby Pro Logic IIx decoding is effective, when a
multi-channel signal is input.
62GB
Types of movie/music mode
Sound field Sound field Effect
for [Display]
Movie Cinema Studio EX A Reproduces the sound characteristics of the Sony Pictures
DCS [C.ST.EX A] Entertainment Cary Grant Theater cinema production
studio. This is a standard mode, great for watching almost any
type of movie.
Cinema Studio EX B Reproduces the sound characteristics of the Sony Pictures
DCS [C.ST.EX B] Entertainment Kim Novak Theater cinema production
studio. This mode is ideal for watching science-fiction or
action movies with lots of sound effects.
Cinema Studio EX C Reproduces the sound characteristics of the Sony Pictures
DCS [C.ST.EX C] Entertainment scoring stage. This mode is ideal for watching
musicals or films where orchestra music is featured in the
soundtrack.
* You can only select this sound field if the headphones are connected to the receiver.
continued
63GB
Notes
The sound fields for music and movies do not work
in the following cases.
Enjoying the surround
PCM signals with a sampling frequency of more
than 48 kHz are being received.
effect at low volume
DTS 96/24 signals are being received. levels
DTS-HD signals with a sampling frequency of
more than 48 kHz are being received. (NIGHT MODE)
Dolby TrueHD signals with a sampling
frequency of more than 48 kHz are being This function allows you to retain a theater like
received. environment at low volume levels. This
The effects provided by the virtual speakers may function can be used with other sound fields.
cause increased noise in the playback signal. When watching a movie late at night, you will
When listening with sound fields that employ the
be able to hear the dialog clearly even at a low
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
volume level.
When one of the sound fields for music is selected, 2CH/
A.DIRECT A.F.D. MOVIE MUSIC
no sound is output from the subwoofer if all the INPUT NIGHT
speakers are set to LARGE in the SPEAKER AUTO CAL MODE SLEEP MODE NIGHT
MODE
menu. However, the sound will be output from the DISPLAY AMP MENU
64GB
Using only the front Listening to the sound
speakers without any adjustment
(2CH STEREO) (ANALOG DIRECT)
In this mode, the receiver outputs the sound You can switch the audio of the selected input to
from the front left/right speakers only. There is 2 channel analog input. This function enables
no sound from the subwoofer. you to enjoy high quality analog sources.
Standard 2 channel stereo sources completely When using this function, only the volume and
bypass the sound field processing and multi front speaker balance can be adjusted.
channel surround formats are downmixed to 2
channel except LFE signals. ?/1
THEATRE RM SET UP AV ?/1
2CH/ 2CH/
A.DIRECT A.F.D. MOVIE MUSIC 1 2 3
A.DIRECT INPUT NIGHT
VIDEO 1 VIDEO 2 BD
AUTO CAL MODE SLEEP MODE
4 5 6
DISPLAY AMP MENU DVD SAT TV
7 8 9 Input
SA-CD/
CD TUNER DMPORT buttons
Press 2CH/A.DIRECT repeatedly to -/-- 0/10 ENT/MEM
HDMI 1 HDMI 2 HDMI 3
select 2CH ST.. CLEAR/>10
HDMI 4
Sound
2CH/
2CH/ A.DIRECT A.F.D. MOVIE MUSIC field
A.DIRECT INPUT NIGHT buttons
AUTO CAL MODE SLEEP MODE
2 Press 2CH/A.DIRECT
repeatedly to select
A.DIRECT.
The analog audio is output.
65GB
Resetting sound fields to Tuner Operations
the initial settings
Listening to FM/AM radio
Be sure to use the buttons on the receiver for
this operation. You can listen to FM and AM broadcasts
?/1
through the built-in tuner. Before operation,
make sure you have connected the FM and
MASTER VOLUME
AM antennas to the receiver (page 30).
?/1
Tip
TONE INPUT SELECTOR
SPEAKERS
Area code FM AM
MUSIC
CEL, CEK 50 kHz 9 kHz
4 5 6 Numeric
DVD SAT TV
buttons
TUNER 7 8 9
SA-CD/ TUNER DMPORT
CD
-/-- 0/10 ENT/MEM ENT/
HDMI 1 HDMI 2 HDMI 3
MEM
CLEAR/>10
HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
INPUT NIGHT
AUTO CAL MODE SLEEP MODE
O
RETURN/ HOME TOOLS/
EXIT OPTIONS
MENU
66GB
Tuning into a station Tuning into a station directly
automatically (Automatic (Direct Tuning)
Tuning) You can enter the frequency of a station
directly by using the numeric buttons.
1 Press TUNER repeatedly to
select the FM or AM band. 1 Press TUNER repeatedly to
select the FM or AM band.
2 Press TUNING + or TUNING .
You can also use INPUT SELECTOR on
Press TUNING + to scan from low to the receiver.
high; press TUNING to scan from high
to low. 2 Press D.TUNING.
The receiver stops scanning whenever a
station is received. 3 Press SHIFT.
Tuner Operations
Select 1 b 0 b 2 b 5 b 0
or AM band.
Example 2: AM 1,350 kHz
2 Press TUNING MODE repeatedly to select
Select 1 b 3 b 5 b 0
AUTO.
3 Press TUNING + or TUNING . 5 Press ENT/MEM.
You can also use MEMORY/ENTER on
In case of poor FM stereo the receiver.
reception
Tip
If the FM stereo reception is poor and ST
If you have tuned in an AM station, adjust the
flashes on the display, select monaural audio
direction of the AM loop antenna for optimum
so that the sound will be less distorted. reception.
To select monaural audio, set FM MODE
in TUNER menu to MONO (page 54).
To return to stereo mode, set FM MODE If you cannot tune in a station
in TUNER menu to STEREO (page 54). Make sure you have entered the right
frequency. If not, repeat steps 2 to 5. If you
still cannot tune in a station, the frequency is
not used in your area.
67GB
Changing the AM tuning scale
Presetting FM/AM radio
(Models of area code AU, TW, TH
only) stations
You can change the AM tuning scale to either You can preset up to 30 FM stations and 30
9 kHz or 10 kHz using the buttons on the AM stations. Then you can easily tune in the
receiver. stations you often listen to.
?/1 SHIFT TV AMP
SHIFT
1 2 3
MASTER VOLUME
VIDEO 1 VIDEO 2 BD
?/1
TONE INPUT SELECTOR
4 5 6
Numeric
SPEAKERS
DVD SAT TV
buttons
TONE MODE INPUT MODE TUNING MODE TUNING
MEMORY/
ENTER
2CH/
A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
TUNER 7 8 9
SA-CD/ TUNER DMPORT
PHONES AUTO CAL MIC VIDEO
VIDEO 2 IN
L AUDIO R CD
-/-- 0/10 ENT/MEM
HDMI 1 HDMI 2 HDMI 3
ENT/
CLEAR/>10
MEM
TUNING MODE HDMI 4
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
TV INPUT WIDE
68GB
2 Tune in the station that you
Tuning to preset stations
want to preset using Automatic
Tuning (page 67) or Direct
Tuning (page 67).
1 Press TUNER repeatedly to
select the FM or AM band.
Switch the FM reception mode, if
necessary (page 67). 2 Press PRESET + or PRESET
repeatedly to select the preset
3 Press SHIFT.
station you want.
4 Press ENT/MEM. Each time you press the button, you can
You can also use MEMORY/ENTER on select a preset station as follows:
the receiver.
1 2 3 4 5 ... 27
MEM lights up for a few seconds.
Perform steps 5 and 6 before MEM 30 29 28
goes out.
You can also press SHIFT and then press
5 Press the numeric buttons to the numeric buttons to select the preset
select a preset number. station you want. Then, press ENT/MEM
Tuner Operations
You can also press PRESET + or to enter the selection.
PRESET to select a preset number.
If MEM goes out before you select the Using the controls on the
preset number, start again from step 3. receiver
6 Press ENT/MEM. 1 Turn INPUT SELECTOR to select the FM
or AM band.
You can also use MEMORY/ENTER on
2 Press TUNING MODE repeatedly to select
the receiver.
PRESET.
MEM lights off.
3 Press TUNING + or TUNING to select the
The station is stored as the selected preset
preset station you want.
number.
69GB
Note (Models of area code CEL, CEK
Naming preset stations only)
When you name an RDS station and tune in that
1 Press TUNER repeatedly to station, the Program Service name appears instead
select the FM or AM band. of the name you entered. (You cannot change the
Program Service name. The name you entered will
You can also use INPUT SELECTOR on be overwritten by the Program Service name.)
the receiver.
9 Press .
The name you entered is registered.
70GB
Displaying RDS information
Using the Radio Data
While receiving an RDS station,
System (RDS) press DISPLAY repeatedly on the
receiver.
(Models of area code CEL, CEK
only) Each time you press the button, RDS
This receiver also allows you to use RDS information on the display changes cyclically
(Radio Data System), which enables radio as follows:
stations to send additional information along Program Service name t Frequency t
with the regular program signal. You can Program Type indicationa) t Radio Text
display RDS information. indicationb) t Current Time indication (in
24-hour system mode) t Sound field
Notes currently applied t Volume level
RDS is operable only for FM stations. a)
Not all FM stations provide RDS service, nor do Type of program being broadcast.
b)Text
they provide the same type of services. If you are messages sent by the RDS station.
not familiar with the RDS services in your area, Notes
check with your local radio stations for details. If there is an emergency announcement by
Tuner Operations
government authorities, ALARM flashes in the
display.
Receiving RDS broadcasts When the message consists of 9 characters or more,
the message scrolls across the display.
Simply select a station on the FM
If a station does not provide a particular RDS
band using Direct Tuning (page 67), service, NO XXXX (such as NO TEXT)
Automatic Tuning (page 67), or appears on the display.
Preset Tuning (page 69).
When you tune in a station that provides RDS Description of program types
services, RDS lights up and the program
service name appears on the display. Program type Description
indication
Note
RDS may not work properly if the station you tuned NEWS News programs
to is not transmitting the RDS signal properly or if AFFAIRS Topical programs that expand on
the signal strength is weak. current news
INFO Programs offering information on
a wide spectrum of subjects,
including consumer affairs and
medical advice
SPORT Sports programs
EDUCATE Educational programs, such as
how-to and advice programs
DRAMA Radio plays and serials
CULTURE Programs about national or
regional culture, such as language
and social concerns
continued
71GB
Program type Description
indication BRAVIA Sync Features
SCIENCE Programs about the natural
sciences and technology
VARIED Other types of programs such as
What is BRAVIA Sync?
celebrity interviews, panel
games, and comedy BRAVIA Sync is compatible with Sony TV,
Blu-ray Disc/DVD player, AV amplifier, etc.,
POP M Popular music programs
that is equipped with the Control for HDMI
ROCK M Rock music programs function.
EASY M Easy Listening By connecting Sony components that are
LIGHT M Instrumental, vocal, and choral compatible with the BRAVIA Sync with an
music HDMI cable (not supplied), operation is
CLASSICS Performances of major
simplified as follows:
orchestras, chamber music, One-Touch Play: When you play back a
opera, etc. component such as a DVD/Blu-ray disc
OTHER M Music that does not fit into any player, the receiver and the TV will switch to
categories above, such as Rhythm the appropriate HDMI input automatically.
& Blues and Reggae In case the receiver or/and the TV is in
WEATHER Weather information standby mode, they will be turned on
automatically.
FINANCE Stock market reports and trading,
etc. System Audio Control: While watching TV,
you can select to output the sound from the
CHILDREN Programs for children
TV speaker or the speakers connected to the
SOCIAL Programs about people and the receiver.
things that affect them
System Power Off: When you turn off the
RELIGION Programs of religious content TV, the receiver and connected components
PHONE IN Programs where members of the are also turned off simultaneously.
public express their views by
phone or in a public forum Control for HDMI is a mutual control function
TRAVEL Programs about travel. Not for standard used by HDMI CEC (Consumer
announcements that are located Electronics Control) for HDMI (High-
by TP/TA. Definition Multimedia Interface).
LEISURE Programs on recreational
activities such as gardening,
fishing, cooking, etc. The Control for HDMI function
does not work in the following
JAZZ Jazz programs
cases:
COUNTRY Country music programs When you connect the receiver to a
NATION M Programs featuring the popular component which does not correspond with
music of the country or region Sony Control for HDMI function.
OLDIES Programs featuring oldies music When you connect the receiver and
components using other than HDMI
FOLK M Folk music programs
connection.
DOCUMENT Investigative features
NONE Any programs not defined above We recommend that you connect the receiver
to products featuring BRAVIA Sync.
72GB
Note
Depending on the connected component, the
Control for HDMI function may not work. Refer to
Preparing for the
the operating instructions of the component. BRAVIA Sync
To use the BRAVIA Sync, turn the Control
for HDMI function on for both the receiver
and the connected component. The receiver is
compatible with the Control for HDMI-Easy
Setting function.
continued
73GB
When your TV is not compatible For details on setting the TV and connected
with the Control for HDMI-Easy components, refer to the operating instructions
Setting function of the respective components.
Turn the Control for HDMI function of the Notes
receiver and the connected component on When you unplug the HDMI cable or change the
individually. connection, perform the steps given in When your
TV is compatible with the Control for HDMI-
2CH/
A.DIRECT A.F.D. MOVIE MUSIC Easy Setting function (page 73) or When your
NIGHT
AUTO CAL
INPUT
MODE SLEEP MODE TV is not compatible with the Control for HDMI-
DISPLAY AMP MENU AMP Easy Setting function (page 74).
MENU You cannot perform One-Touch Play and System
Audio Control during the Control for HDMI-Easy
, Setting operation.
V/v/B/b
Before you do the Control for HDMI-Easy Setting
from the TV, be sure to turn on the TV, connected
O
RETURN/ HOME TOOLS/ components and receiver.
EXIT OPTIONS
MENU If the playback components cannot function after
you have made the settings for Control for HDMI-
1 Perform the steps given in When your Easy Setting, check the Control for HDMI setting
TV is compatible with the Control for on your TV.
HDMI-Easy Setting function If the connected components do not support
Control for HDMI-Easy Setting, you need to set
(page 73).
the Control for HDMI function for the connected
2 Press AMP MENU. components to on before you perform the Control
for HDMI-Easy Setting from the TV.
3 Press V/v repeatedly to select HDMI.
4 Press or b to enter the menu.
5 Press V/v repeatedly to select
CTRL:HDMI.
6 Press or b to enter the parameter.
7 Press V/v repeatedly to select CTRL
ON.
Control for HDMI function is activated.
8 Select the HDMI input of the receiver
and TV to match the HDMI input of the
connected component, so that the
image from the connected component
is displayed.
9 Set the Control for HDMI function for
the connected component to on.
If the Control for HDMI function for the
connected component is already set to on,
you do not need to change the setting.
10Repeat steps 8 and 9 for other
components that you want to use the
Control for HDMI function.
74GB
Watching a DVD/Blu-ray Enjoying the TV sound
disc from the speakers
(One-Touch Play) connected to the receiver
You can enjoy sound and image from the (System Audio Control)
components connected to the receiver via
HDMI connections by a simple operation. You can enjoy the TV sound from the speakers
connected to the receiver by a simple
Play back a connected component. operation.
The receiver and the TV will switch to the You can operate System Audio Control
appropriate HDMI input automatically. function using the TV menu. For details, refer
In case the receiver or/and the TV is in standby to the operating instructions of the TV.
mode, they will be turned on automatically. When System Audio Control function is
turned on, the receiver will turns on and
switches to the appropriate input
Watching a DVD/Blu-ray disc by automatically.
simple operation TV sound is output from the speakers
You can also select a connected component, connected to the receiver, and the volume of
such as a DVD/Blu-ray disc player using the the TV is minimized simultaneously.
TV menu. In this case, the receiver and the TV You can also use the System Audio Control
75GB
Turning off the receiver S-AIR Operations
with the TV
(System Power Off) About S-AIR products
This receiver is compatible with the S-AIR
When you turn the TV off by using the
function (page 102), which allows wireless
POWER button on the TVs remote, the
sound transmission between S-AIR products.
receiver and the connected components turn
When you purchase the S-AIR product, you
off automatically.
need to establish sound transmission (page
You can also use the receivers remote to turn
79).
off the TV.
There are two types of S-AIR product.
S-AIR main unit (this receiver):
THEATRE RM SET UP AV ?/1
?/1 The S-AIR main unit is for transmitting
AV ?/1
sound.
SYSTEM STANDBY
SHIFT TV AMP
You can use up to 3 S-AIR main units. (The
1 2 3 TV number of usable S-AIR main unit depends
VIDEO 1 VIDEO 2 BD
on the use environment.)
4 5 6
DVD SAT TV
S-AIR sub unit (not supplied): The S-AIR
7 8 9 sub unit is for receiving sound.
SA-CD/
CD TUNER DMPORT
Surround amplifier: You can enjoy
surround and surround back speakers
Press TV, then press AV ?/1. sound wirelessly. For details, refer to the
The TV, receiver and the components operating instructions supplied with the
connected via HDMI are turned off. surround amplifier.
S-AIR receiver: You can enjoy system
Notes sound in another room.
Set the TV Standby Synchro to ON before using These S-AIR products can be purchased as an
the System Power Off function. For details, refer to option (the S-AIR product lineup differs
the operating instructions of the TV.
depending on the area).
Depending on the status, the connected
components may not be turned off. For details,
Notes or instructions for the surround
refer to the operating instructions of the connected amplifier or S-AIR receiver in this operating
components. instructions refer only to when the surround
amplifier or S-AIR receiver is used.
76GB
Room B Setting up an S-AIR
S-AIR sub unit
(S-AIR receiver)
product
Before using an S-AIR product, be sure to
perform the following settings to establish the
Room A S-AIR main unit sound transmission.
(this receiver)
MASTER VOLUME
?/1
SPEAKERS
TONE INPUT SELECTOR
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
S-AIR Operations
continued
77GB
To insert the wireless Notes
transmitter into the S-AIR main Insert the wireless transmitter with the S-AIR logo
unit facing up.
Insert the wireless transmitter so that the V marks
1 Remove the screws and detach the slot are aligned.
cover. Do not insert other than the wireless transmitter
into the EZW-T100 slot.
Slot cover
3 Use the screws that you removed from
step 1 to fasten the wireless transmitter.
0
-T10
EZW
0
-T10
E ZW
ANTENNA
AM
IN 4
EZW-T100
ASSIG
TV DIGITAL (ASSIG
Y
IN 3 IN 2 IN 1
MONITOR
OUT DMPORT
DC5V
0.7A MAX SAT BD
Note
IN IN IN
PB/
CB
OPTICAL OPTICAL Do not use other screws to fasten the wireless
VIDEO VIDEO VIDEO VIDEO VIDEO
PR /
CR
IN IN OUT IN OUT
transmitter.
SURROUND BACK/
COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) AUDIO AUDIO AUDIO AUDIO
MONITOR BI-AMP/
OUT IN IN IN IN OUT IN FRONT B
L
AUDIO R
R
OUT
0
-T10
EZW
Wireless transmitter
78GB
Sound transmission is established as
Establishing sound transmission follows (example):
between the S-AIR main unit and
S-AIR sub unit (ID setting) S-AIR main unit
Other S-AIR
MASTER VOLUME
?/1
TONE INPUT SELECTOR
main unit
When you match the ID of the S-AIR main
SPEAKERS
MEMORY/ 2CH/
ID A ID B
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
, Notes
V/v/B/b
Sources with copyright protection may not be
playable on S-AIR sub unit.
O
RETURN/ HOME TOOLS/
MENU/
When sound transmission is established
EXIT OPTIONS
MENU
HOME sound can only be output from the S-AIR
receiver if you connect the components to this
receiver via the analog jacks. The sound cannot
To set the ID of the S-AIR main be output if the components are connected to the
unit COAXIAL, OPTICAL or HDMI jacks on this
receiver.
1 Press AMP MENU. the headphones function on the surround
amplifier is not available.
2 Press V/v repeatedly to select S-AIR.
S-AIR Operations
3 Press or b to enter the menu.
4 Press V/v repeatedly to select S-AIR
ID.
5 Press or b to enter the parameter.
6 Press V/v repeatedly to select the ID
(A, B or C) you want, then press .
79GB
x After pairing
Pairing the S-AIR main unit with Sound transmission is established between the
a specific S-AIR sub unit paired S-AIR main unit and S-AIR sub unit(s)
(Pairing operation) only.
Your room Neighbor
To establish sound transmission, you need to
set the same ID for your S-AIR main unit and S-AIR main unit
S-AIR sub unit. ?/1
MASTER VOLUME
MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
?/1
TONE INPUT SELECTOR
SPEAKERS
main unit.
MEMORY/ 2CH/
TONE MODE INPUT MODE TUNING MODE TUNING ENTER A.DIRECT A.F.D. MOVIE MUSIC DISPLAY DIMMER MUTING
VIDEO 2 IN
PHONES AUTO CAL MIC VIDEO L AUDIO R
ID A
2 Match the IDs of the S-AIR main
unit and the S-AIR sub unit.
To set the ID of the S-AIR main unit,
see To set the ID of the S-AIR main
ID A ID A unit (page 79).
S-AIR sub unit S-AIR sub unit
To set the ID of the S-AIR sub unit,
refer to the operating instructions
supplied with the S-AIR sub unit.
80GB
8 Press V/v repeatedly to select
the setting you want, then Enjoying the systems
press .
START: The S-AIR main unit starts sound in another room
pairing. SEARCHING flashes on the
(For the S-AIR receiver only (not
display.
supplied))
CONDITION: You can check the
You can enjoy the systems sound in another
current ID. When the pairing setting is
room by using the S-AIR receiver. The S-AIR
not made, NO PAIRING appears on
receiver can be placed in another room for
the display.
enjoying the systems sound there.
9 Start pairing of the S-AIR sub For details of the S-AIR receiver, refer to the
operating instructions supplied with the S-AIR
unit.
receiver.
x For the surround amplifier SHIFT TV AMP
4 5 6
DVD SAT TV
x For the S-AIR receiver 7 8 9 Input
Refer to the operating instructions SA-CD/
CD TUNER DMPORT buttons
-/-- 0/10
supplied with the S-AIR receiver. HDMI 1 HDMI 2
ENT/MEM
HDMI 3
10 Pairing completed.
CLEAR/>10
HDMI 4
INPUT NIGHT
AUTO CAL MODE SLEEP MODE
To exit the menu
AMP
S-AIR Operations
DISPLAY AMP MENU
Press MENU/HOME or AMP MENU. MENU
Note ,
Perform the pairing within several minutes after step V/v/B/b
8. Otherwise, the pairing is canceled automatically
O
and INCOMPLETE appears on the display.
RETURN/ HOME TOOLS/
EXIT OPTIONS
MENU
To cancel pairing
Reset the ID of the S-AIR main unit.
For details, see To set the ID of the S-AIR
1 Set the ID of the S-AIR receiver
to match the ID of the S-AIR
main unit (page 79). You can select the same
main unit.
ID as before.
To set the ID of the S-AIR main unit,
see To set the ID of the S-AIR main
unit (page 79).
To set the ID of the S-AIR receiver,
refer to the operating instructions
supplied with the S-AIR receiver.
continued
81GB
Notes 8 Adjust the volume on the
When you are using another S-AIR sub unit, S-AIR receiver.
such as a surround amplifier, do not change
the ID of the S-AIR main unit. Set the ID of Note
the S-AIR receiver to match the ID of the The sound of the S-AIR receiver may be cut off by
S-AIR main unit. operation of the S-AIR main unit.
When you pair the S-AIR main unit and
another S-AIR sub unit, such as a surround
amplifier, you also need to pair the S-AIR
main unit and the S-AIR receiver. For details,
see Pairing the S-AIR main unit with a
specific S-AIR sub unit (Pairing operation)
(page 80).
82GB
6 Press V/v repeatedly to select
Changing the channel the setting you want, then
press .
for better sound RF AUTO: Normally select this. The
transmission system changes RF CHANGE to RF
ON or RF OFF automatically.
If you use multiple wireless systems which RF ON: The system transmits sound by
sharing the 2.4 GHz band, such as wireless searching the better channel for
LAN or Bluetooth, the transmission of S-AIR transmitting.
products or other wireless systems may be RF OFF: The system transmits sound by
unstable. In this case, the transmission may be fixing the channel for transmitting.
improved by changing the following RF
CHANGE setting.
To exit the menu
Press MENU/HOME or AMP MENU.
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
Notes
INPUT NIGHT
AUTO CAL MODE SLEEP MODE
When the wireless transmitter is not inserted in the
DISPLAY AMP MENU AMP S-AIR main unit, you cannot set RF CHANGE.
MENU In most cases, you will not need to change this
setting.
,
If RF CHANGE is set to RF OFF,
V/v/B/b
transmission between the S-AIR main unit and
O S-AIR sub unit can be performed using one of the
RETURN/
EXIT
HOME TOOLS/
OPTIONS
MENU/ following channels.
MENU
HOME S-AIR ID A: equivalent channel for IEEE
802.11b/g channel 1
1 Press AMP MENU.
S-AIR ID B: equivalent channel for IEEE
S-AIR Operations
802.11b/g channel 6
2 Press V/v repeatedly to select
S-AIR ID C: equivalent channel for IEEE
802.11b/g channel 11
S-AIR. The transmission may be improved by changing
the transmission channel (frequency) of the other
3 Press or b to enter the wireless system(s). For details, refer to the
menu. operating instructions of the other wireless
system(s).
4 Press V/v repeatedly to select
RF CHANGE.
83GB
6 Press V/v repeatedly to select
Enjoying the S-AIR the setting you want.
STBY OFF: You cannot enjoy the
receiver while the S-AIR S-AIR receiver while the S-AIR main
main unit is in standby unit is in standby mode.
STBY ON: You can enjoy the S-AIR
mode receiver while the S-AIR main unit is in
standby mode or turned on.
(For the S-AIR receiver only (not
supplied)) To exit the menu
You can enjoy the S-AIR receiver while the Press MENU/HOME or AMP MENU.
S-AIR main unit is in standby mode by setting
S-AIR STBY to STBY ON. Notes
When you set S-AIR STBY to STBY ON, the
SHIFT TV AMP power consumption increases during the standby
1 2 3 mode.
VIDEO 1 VIDEO 2 BD When the wireless transmitter is not inserted in the
4 5 6 S-AIR main unit, you cannot set S-AIR STBY.
DVD SAT TV
Input When the wireless transmitter is removed from the
7 8 9
SA-CD/
CD TUNER DMPORT buttons S-AIR main unit, S-AIR STBY is set to STBY
-/-- 0/10 ENT/MEM OFF automatically.
HDMI 1 HDMI 2 HDMI 3
If you have selected TUNER (FM/AM band) on
CLEAR/>10
HDMI 4
the S-AIR main unit before you turn it off and
2CH/
S-AIR STBY is set to STBY ON, you can only
A.DIRECT A.F.D. MOVIE MUSIC
select the same band for the tuner on the S-AIR
INPUT NIGHT
AUTO CAL MODE SLEEP MODE receiver. However, you can select input other than
DISPLAY AMP MENU AMP TUNER on the S-AIR receiver.
MENU The sound of the S-AIR receiver may be cut off by
operation of the S-AIR main unit.
,
V/v/B/b
O
RETURN/
EXIT
HOME TOOLS/
OPTIONS
MENU/
MENU HOME
84GB
Other Operations Enjoying the sound/
images from other inputs
Switching between
You can reassign audio and/or video signals to
digital and analog audio another input when they are not currently
being used.
(INPUT MODE) For example, connect the OPTICAL OUT jack
of the DVD player to the OPTICAL BD IN
When you connect components to both digital
jack of this receiver when you want to input
and analog input jacks on the receiver, you can
the digital optical audio signals from the DVD
fix the audio input mode to either of them, or
player.
switch from one to the other, depending on the
Connect the component video jack of the DVD
type of material you intend to watch.
player to the COMPONENT VIDEO IN 1 jack
1 Turn INPUT SELECTOR on the of this receiver when you want to input the
receiver to select the input. video signals from the DVD player.
Assign audio and/or video signals to the DVD
You can also use the input buttons on the
input jack using A. ASSIGN and/or V.
remote.
ASSIGN in the AUDIO and/or VIDEO menu
2 Press INPUT MODE repeatedly respectively.
on the receiver to select the 1 Press AMP MENU.
audio input mode.
The selected audio input mode appears on 2 Press V/v repeatedly to select
the display. AUDIO or VIDEO.
Other Operations
Gives priority to digital audio signals when
there are both digital and analog connections. A. ASSIGN or V. ASSIGN.
If there are no digital audio signals, analog
audio signals are selected.
5 Press or b to enter the
parameter.
x ANALOG
Specifies the analog audio signals input to the
6 Press V/v repeatedly to select
AUDIO IN (L/R) jacks. the input name you want to
assign (for example, DVD).
Notes
Some audio input modes may not be set up 7 Press or b to enter your
depending on the input. selection.
When the ANALOG DIRECT function is selected,
audio input is set to ANALOG automatically and
you cannot select other modes.
When HDMI 14 or DMPORT input is selected,
------ appears on the display, and you cannot
select other modes. Select an input mode other than
the HDMI 14 and DMPORT input, then set the
audio input mode.
continued
85GB
8 Press V/v repeatedly to select
the input jack you want to
assign to the input which you
selected in step 6.
* Initial setting
Notes
You cannot assign optical signals from an input
source to the optical input jacks on the receiver, and
you cannot assign coaxial signals from the input
source to the coaxial input jacks on the receiver.
When you assign the digital audio input, the
INPUT MODE setting may change automatically
(page 85).
You cannot reassign more than one HDMI input to
the same input.
You cannot reassign more than one digital audio
input to the same input.
You cannot reassign more than one component
video input to the same input.
86GB
Enjoying the DIGITAL
MEDIA PORT
(DMPORT)
The DIGITAL MEDIA PORT (DMPORT)
allows you to enjoy sound from a network
system such as a portable audio source or
computer.
By connecting a DIGITAL MEDIA PORT
adapter (not supplied), you can enjoy sound
from the connected component on the
receiver.
For details, refer to the operating instructions
supplied with the DIGITAL MEDIA PORT
adapter.
Notes
Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
Before connecting cords, be sure to disconnect the
AC power cord.
Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is turned
on.
Depending on the DIGITAL MEDIA PORT
adapter, video output may not be possible.
The DIGITAL MEDIA PORT adapters are
available for purchase depending on the area.
Other Operations
87GB
Connecting the DIGITAL MEDIA
PORT adapter
You can listen to the sound and view the
images from the component connected
through the DIGITAL MEDIA PORT adapter
to the DMPORT jack on the receiver.
TV
ANTENNA
AM
EZW-T100
MONITOR
TV
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX
PB/
OPTICAL A
CB
VIDEO VIDEO VIDEO VIDEO VIDEO
IN IN OUT IN OUT
PR/
CR
L
AUDIO
OUT
DIGITAL MEDIA
PORT adapter
88GB
Listening/watching a connected
component through DMPORT Changing the display
connection You can check the sound field, etc., by
changing the information on the display.
1 Press DMPORT. Be sure to use the buttons on the receiver for
You can also use the INPUT SELECTOR this operation.
on the receiver to select DMPORT. Press DISPLAY repeatedly.
2 Start playback of the connected
Each time you press the button, the display
changes cyclically as follows:
component.
The sound is played back on the receiver
and the image appears on the TV. All inputs except the FM and AM
For details, refer to the operating band
instructions supplied with the DIGITAL Index name of the inputa) t Selected input
MEDIA PORT adapter. t Sound field currently applied t Volume
level t Stream info
Notes
Depending on the type of DIGITAL MEDIA
PORT adapter, you can operate the connected FM and AM band
component by using the remote. For details on Program Service nameb) or preset station
remote button operation, see page 11. namea) t Frequency t Program Type
Be sure you have connected the MONITOR OUT indicationb) t Radio Text indicationb) t
jack of the receiver to the TV (page 88). Current Time indication (in 24-hour system
mode)b) t Sound field currently applied t
Tip
When listening to MP3 or other compressed music
Volume level
using a portable audio source, you can enhance the a)
sound. Press MUSIC repeatedly to select Index name appears only when you have assigned
PORTABLE (page 63). one to the input or preset station (page 41, 70).
Index name does not appear when only blank
Other Operations
spaces have been entered, or it is the same as the
input name.
b)During RDS reception only (Models of area code
Note
Character or marks may not be displayed for some
languages.
89GB
Using the Sleep Timer Recording using the
You can set the receiver to turn off receiver
automatically at a specified time.
You can record from a video/audio component
Press SLEEP repeatedly while the using the receiver. Refer to the operating
power is on. instructions supplied with your recording
SLEEP lights up in the display. component.
Each time you press SLEEP, the display
changes cyclically as follows:
Recording onto a CD-R
You can record onto a CD-R using the
0-30-00 t 1-00-00 t 1-30-00 t 2-00-00 receiver. See the operating instructions
t OFF supplied with your CD recorder.
Tip
To check the remaining time before the receiver
1 Press one of the input buttons
turns off, press SLEEP. The remaining time appears to select the playback
on the display. If you press SLEEP again, the sleep component.
timer will be canceled. You can also use INPUT SELECTOR on
the receiver.
90GB
Recording onto a recording
media Using a bi-amplifier
connection
1 Press one of the input buttons
to select the playback If you are not using surround back speakers,
component. you can connect the front speakers to the
You can also use INPUT SELECTOR on SPEAKERS SURROUND BACK/BI-AMP/
the receiver. FRONT B terminals using a bi-amplifier
connection.
2 Prepare the playback
component for playing. To connect speakers
For example, insert the video tape you
Front speaker Front speaker
want to copy into the VCR. (R) (L)
Lo Lo
MONITOR
TV DIGITAL (ASSIGNABLE)
IN 3 IN 2 IN 1
OUT DMPORT
DC5V
Y 0.7A MAX SAT BD DVD
IN IN IN IN
4
PR/
CR
SURROUND BACK/
COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) AUDIO AUDIO AUDIO AUDIO
MONITOR BI-AMP/
OUT IN IN IN IN OUT IN FRONT B
FRONT A
L
AUDIO R L R L
SURROUND BACK/
component. BI-AMP/
FRONT B
FRONT A
R L R L
Note SPEAKERS
Other Operations
Connect the jacks on the Lo (or Hi) side of the
front speakers to the SPEAKERS FRONT A
terminals, and connect the jacks on the Hi (or
Lo) side of the front speakers to the
SPEAKERS SURROUND BACK/BI-AMP/
FRONT B terminals.
Make sure that metal fittings of Hi/Lo attached
to the speakers have been removed from the
speakers. Not doing so may cause a
malfunction of the receiver.
continued
91GB
To set up speakers To exit the menu
Press MENU/HOME or AMP MENU.
2CH/
A.DIRECT A.F.D. MOVIE MUSIC
AUTO CAL
INPUT
SLEEP
NIGHT
MODE
Notes
MODE
Set SB ASSIGN to BI-AMP before you
DISPLAY AMP MENU AMP perform auto calibration.
MENU
If you set SB ASSIGN to BI-AMP, the speaker
, level and distance settings of the surround back
V/v/B/b speakers become invalid, and those of the front
speakers are used.
O
If you set SP PATTERN to a setting with
RETURN/ HOME TOOLS/ MENU/
EXIT
MENU
OPTIONS surround back speakers, you cannot set SB
HOME
ASSIGN to BI-AMP.
7 Press or B.
92GB
Using the Remote
Operating each
component using the
remote
You can control Sony or non-Sony
components you are using with the remote
supplied with the receiver.
The remote is initially set to control Sony
components.
When you change the settings of the remote
according to the components you are using,
you can control non-Sony and other Sony
components that the remote is initially unable
control (page 95).
93GB
Table of buttons used to control each component (Main remote
commander)
Component TV VCR DVD Blu-ray HDD PSX Video Digital Tape DAT CD DIGITAL
player, Disc Recorder CD satellite/ deck deck player, MEDIA
DVD/ Player player, terres- A/B MD PORT
VHS LD trial deck device
combo player receiver
Button (EURO)
AV ?/1 a a a a a a a a a a
Numeric buttons a a a a a a a a a a a a
TV INPUT,
a
WIDE
-/--, CLEAR/>10 a a a a a a a a a
ENT/MEM a a a a a a a*1 a a a
DISPLAY a a a a a a a a
RETURN/EXIT a a a a a a a a
TOOLS/
a a a a a
OPTIONS
V/v/B/b, ,
a a a a a a a a
MENU, HOME
., > a a a a a a a a*3 a a a
< , < a a a a a a
m/TUNING ,
a a a a a a a a a a a
M/TUNING +
DISC SKIP a a a*2 a
N, X, x a a a a a a a a a a a
MUTING,
MASTER VOL a
+/, TV VOL +/
PRESET +/,
a a a a a a*1 a
TV CH +/
BD/DVD TOP
MENU, BD/DVD a a a
MENU
F1, F2 a a
*1
LD player only.
*2
VIDEO CD only.
*3
DECK B only.
94GB
5 Repeat steps 1 to 4 to control
Programming the remote other components.
Notes
You can program the remote to control non- The indicator turns off while a valid button is
Sony components by changing the code. Once pressed.
the control signals have been memorized, you In step 2, if you want to change to other input, press
can use those components as part of your SHIFT and then press the new input buttons you
system. want.
Furthermore, you can also program the remote In step 2, if you press TUNER, you can only
for Sony components that the remote is unable program the button to control a tuner (page 96).
For the numeric codes, only the last three numbers
to control. Note that the remote can only
entered are valid.
control components that accept infrared
wireless control signals.
To program the remote to
1 Press AV ?/1 while pressing control a TV
RM SET UP. 1 Press AV ?/1 while pressing RM SET UP.
The RM SET UP button slowly flashes. The RM SET UP indicator slowly flashes.
2 Press TV.
2 Press the input button for the The RM SET UP and the SHIFT button
component you want to control. indicator light up.
For example, if you are going to control a 3 Press the numeric buttons to enter the
CD player, press SA-CD/CD. numeric code (or one of the codes if more
The RM SET UP and the SHIFT button than one code exists) for TV. For details, see
indicator light up. page 97.
4 Press ENT/MEM.
3 Press the numeric buttons to Once the numeric code has been verified,
enter the numeric code (or one the RM SET UP indicator slowly flashes
of the codes if more than one twice and the remote automatically exits the
code exists) corresponding to programming mode.
the component and the maker
of the component you want to To cancel programming
control (except TV). Press RM SET UP during any step. The RM
See the tables on page 9699 for SET UP indicator flashes 5 times in quick
Using the Remote
information on the numeric code(s) succession. The remote automatically exits the
corresponding to the component and the programming mode.
maker of the component (the first digit
and the last two digits of the numeric code To activate the input after
correspond to the category and the programming
makers code respectively). Press the programmed button to activate the
input you want.
4 Press ENT/MEM.
Once the numeric code has been verified,
the RM SET UP indicator slowly flashes
twice and the remote automatically exits
the programming mode.
continued
95GB
If programming is To control a tuner
unsuccessful, check the Maker Code(s)
following: SONY 002, 005
If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
If the indicator flashes 5 times in quick To control a CD player
succession while entering the numeric code, Maker Code(s)
an error has occurred. Start again from step SONY 101, 102, 103
1. DENON 104, 123
JVC 105, 106, 107
To clear the memory of the KENWOOD 108, 109, 110
remote MAGNAVOX 111, 116
To clear all programmes, do the following to
MARANTZ 116
reset the remote to factory settings.
ONKYO 112, 113, 114
While holding down MASTER PANASONIC 115
VOL , press and hold ?/1 and then PHILIPS 116
press AV ?/1. PIONEER 117
The indicator flashes 3 times, then goes off. TECHNICS 115, 118, 119
YAMAHA 120, 121, 122
The numeric codes
corresponding to the To control a DAT deck
component and the maker of Maker Code(s)
the component
SONY 203
Use the numeric codes in the tables below to
PIONEER 219
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a To control a tape deck
component accepts differs depending on the Maker Code(s)
model and year of the component, more than
SONY 201, 202
one numeric code may be assigned to a
DENON 204, 205
component. If you fail to program your remote
using one of the codes, try using other codes. KENWOOD 206, 207, 208, 209
NAKAMICHI 210
Notes
PANASONIC 216
The numeric codes are based on the latest
information available for each brand. There is a PHILIPS 211, 212
chance, however, that your component will not PIONEER 213, 214
respond to some or all of the codes. TECHNICS 215, 216
All of the input buttons on this remote may not be
YAMAHA 217, 218
available when used with your particular
component.
96GB
To control an MD deck To control a DVD/VHS COMBO
Maker Code(s) Maker Code(s)
SONY 301 SONY 411
DENON 302
JVC 303 To control a DVD/HDD COMBO
KENWOOD 304 Maker Code(s)
SONY 401, 402, 403
To control an HDD recorder
Maker Code(s) To control a TV
SONY 307, 308, 309 Maker Code(s)
SONY 501, 502
To control a Blu-ray disc player/ AIWA 501, 536, 539
recorder AKAI 503
Maker Code(s) AOC 503
SONY 310, 311, 312 CENTURION 566
CORONADO 517
To control a PSX CURTIS-MATHES 503, 551, 566, 567
Maker Code(s) DAYTRON 517, 566
SONY 313, 314, 315 DAEWOO 504, 505, 506, 507,
515, 544
FISHER 508, 545
To control a DVD player
FUNAI 548
Maker Code(s)
FUJITSU 528
SONY 401, 402, 403
GOLDSTAR/LG 503, 512, 515, 517,
BROKSONIC 424 534, 544, 556, 568
DENON 405 GRUNDIG 511, 533, 534
HITACHI 416 HITACHI 503, 513, 514, 515,
JVC 415, 423 517, 519, 544, 557,
571
MITSUBISHI 419
ITT/NOKIA 521, 522
ORITRON 417 Using the Remote
J.C.PENNY 503, 510, 566
PANASONIC 406, 408, 425
JVC 516, 552
PHILIPS 407
KMC 517
PIONEER 409, 410
MAGNAVOX 503, 515, 517, 518,
RCA 414 544, 566
SAMSUNG 416, 422 MARANTZ 527
TOSHIBA 404, 421 MITSUBISHI/MGA 503, 519, 527, 544,
ZENITH 418, 420 566, 568
NEC 503, 517, 520, 540,
544, 554, 566
To control a DVD recorder
NORDMENDE 530, 558
Maker Code(s)
NOKIA 521, 522, 573, 575
SONY 401, 402, 403
PANASONIC 509, 524, 553, 559,
572
continued
97GB
Maker Code(s) To control an LD player
PHILIPS 515, 518, 557, 570, Maker Code(s)
571
SONY 601, 602, 603
PHILCO 503, 504, 514, 517,
518 PIONEER 606
98GB
To control a satellite tuner (box)
Maker Code(s) Additional Information
SONY 801, 802, 803, 804,
824, 825, 865
AMSTRAD 845, 846
Glossary
BskyB 862
x Cinema Studio EX
GENERAL ELECTRIC 866 A surround sound mode that can be regarded
(GE)
as the compilation of Digital Cinema Sound
GRUNDIG 859, 860
technology, delivers the sound of a dubbing
HUMAX 846, 847 theater using three technologies: Virtual
THOMSON 857, 861, 864, 876 Multi Dimensions, Screen Depth Matching,
PACE 848, 849, 850, 852, and Cinema Studio Reverberation.
862, 863, 864 Virtual Multi Dimensions, the virtual
PANASONIC 818, 855 speaker technology, creates a virtual multi-
PHILIPS 856, 857, 858, 859, surround environment with actual speakers up
860, 864, 874 to 7.1 channels, and brings the surround sound
NOKIA 851, 853, 854, 864 experience of a theater with the latest facilities
RCA/PROSCAN 866, 871 into your home.
BITA/HITACHI 868
Screen Depth Matching reproduces treble
attenuation, fullness, and depth of sound
HUGHES 867
usually created in a theater using sound
JVC/Echostar/Dish 873
emission from behind the screen. This is then
Network
added to the front and center channels.
MITSUBISHI 872
Cinema Studio Reverberation reproduces
SAMSUNG 875 the sound characteristics of state-of-the-art
TOSHIBA 869, 870 dubbing theaters and recording studios,
including Sony Pictures Entertainments
To control a cable box dubbing studios. There are three modes, A/B/
C, available according to the studio type.
Maker Code(s)
SONY 821, 822, 823 x Component video
HAMLIN/REGAL 836, 837, 838, 839, A format for transmitting video signal
840 information consisting of three separate
JERROLD/G.I./ 806, 807, 808, 809, signals: luminance Y, chrominance Pb, and
MOTOROLA 810, 811, 812, 813, chrominance Pr. High quality pictures, such as
814, 819
DVD video or HDTV pictures, are transmitted
JERROLD 830, 831
Additional Information
continued
99GB
x Deep Color x Dolby Digital Surround EX
Video signals for which the color depth of Acoustic technology developed by Dolby
signals passing through an HDMI jack have Laboratories, Inc. Surround back information
been raised. is matrixed into regular left and right surround
The number of colors that could be expressed channels so that the sound can be reproduced
by 1 pixel was 24 bits (16,777,216 colors) with in 6.1 channel. Active scenes, especially, are
the current HDMI jack. However, the number recreated with a more dynamic and realistic
of colors which can be expressed by 1 pixel sound field.
will be 36 bits, etc., when the receiver
corresponds to Deep Color. x Dolby Pro Logic II
Since the gradation of the depth of a color can This technology converts 2 channel stereo
be expressed more finely with more bits, recorded audio into 5.1 channel for playback.
continuous color changes can be more There is a MOVIE mode for movies and
smoothly expressed. MUSIC mode for stereo sources such as
music. Old movies encoded in the traditional
x Digital Cinema Sound (DCS) stereo format can be enhanced with 5.1
A unique sound reproduction technology for channel surround sound.
home theater developed by Sony, in The GAME mode is suitable for video games.
cooperation with Sony Pictures Entertainment,
for enjoying the exciting and powerful sound x Dolby Pro Logic IIx
of movie theaters at home. With this Digital Technology for 7.1 channel (or 6.1 channel)
Cinema Sound developed by integrating a playback. Along with audio encoded in Dolby
DSP (Digital Signal Processor) and measured Digital Surround EX, 5.1 channel Dolby
data, the ideal sound field intended by Digital encoded audio can be reproduced in
filmmakers can be experienced at home. 7.1 channel (or 6.1 channel). Furthermore,
existing stereo recorded content can also be
x Dolby Digital reproduced in 7.1 channel (or 6.1 channel).
Digital audio encoding/decoding technology
developed by Dolby Laboratories, Inc. It x Dolby Surround (Dolby Pro
consists of front (left/right), center, surround Logic)
Audio processing technology developed by
(left/right) and subwoofer channels. It is a
Dolby Laboratories, Inc. Center and mono
designated audio standard for DVD video and
surround information is matrixed into two
also known as 5.1 channel surround. Since
stereo channels. When reproduced, audio is
surround information is recorded and
decoded and output in 4 channel surround
reproduced in stereo, more realistic sound with
sound. This is the most common audio
fuller presence is delivered than with Dolby
processing method for DVD video.
surround.
x Dolby TrueHD
x Dolby Digital Plus
Dolby TrueHD is Dolbys lossless audio
Dolby Digital Plus provides the flexibility and
technology developed for high-definition
efficiency to deliver more channels of
optical discs. Dolby TrueHD audio is bit-for-
compelling surround sound for high-definition
bit identical to the original studio masters and
video media. Its superior coding efficiencies
provides supreme-quality audio up to 8
enable up to 7.1ch of high-quality
channel at 96 kHz/24 bit and up to 6ch at
multichannel audio without negatively
192 kHz/24 bit. Together with high-definition
impacting bit budgets allocated for video
video, it offers an unprecedented home theater
performance or additional feature sets.
experience.
100GB
x DTS 96/24 x DTS Neo:6
A high sound quality digital signal format. It This technology converts 2 channel stereo
records audio at a sampling frequency and bit recorded audio for 6.1 channel playback.
rate of 96 kHz/24bit which is the highest There are two modes to select according to the
possible for DVD video. The number of playback source or your preference, CINEMA
playback channels varies depending on the for movies, and MUSIC for stereo sources
software. such as music.
continued
101GB
x S-AIR (Sony Audio Interactive
Radio frequency)
Recent times have seen the rapid spread of
Precautions
DVD media, Digital Broadcasting, and other
high quality media. On safety
To ensure that the subtle nuances of these high Should any solid object or liquid fall into the
quality media are transmitted with no cabinet, unplug the receiver and have it
deterioration, Sony has developed a checked by qualified personnel before
technology called S-AIR for the radio operating it any further.
transmission of digital audio signals with no
compression, and has incorporated this
technology into the EZW-RT10/EZW-T100. On power sources
This technology transfers digital audio signals Before operating the receiver, check that the
with no compression using the 2.4 GHz band operating voltage is identical with your local
range of ISM band (Industrial, Scientific, and power supply.
Medical band), such as wireless LANs and The operating voltage is indicated on the
Bluetooth applications. nameplate on the back of the receiver.
The unit is not disconnected from the AC
x Sampling frequency power source (mains) as long as it is
To convert analog audio to digital, analog data connected to the wall outlet, even if the unit
should be quantified. This process is called itself has been turned off.
sampling, and the number of times per second If you are not going to use the receiver for a
the analog data is quantified is called the long time, be sure to disconnect the receiver
sampling frequency. A standard music CD from the wall outlet. To disconnect the AC
stores data quantified at 44,100 times per power cord (mains lead), grasp the plug
second, which is expressed as a sampling itself; never pull the cord.
frequency of 44.1 kHz. Generally speaking, a The AC power cord (mains lead) must be
higher sampling frequency means better sound changed only at a qualified service shop.
quality.
On heat buildup
x x.v.Colour Although the receiver heats up during
x.v.Colour is a more familiar term for the operation, this is not a malfunction. If you
xvYCC standard proposed by Sony, and is a continuously use this receiver at a large
trademark of Sony. xvYCC is an international volume, the cabinet temperature of the top,
standard for color space in video. side and bottom rises considerably. To avoid
This standard can express a wider colour range burning yourself, do not touch the cabinet.
than the currently used broadcast standard.
102GB
On placement About S-AIR function
Place the receiver in a location with adequate As the S-AIR function transmits sound by
ventilation to prevent heat buildup and radio waves, sound may skip when radio
prolong the life of the receiver. waves are obstructed. This is a characteristic
Do not place the receiver near heat sources, of radio waves and is not malfunction.
or in a place subject to direct sunlight, As the S-AIR function transmits sound by
excessive dust, or mechanical shock. radio waves, equipment that generates
Do not place anything on top of the cabinet electromagnetic energy, such as a
that might block the ventilation holes and microwave oven, may interfere with sound
cause malfunctions. transmission.
Do not place the receiver near equipment As the S-AIR function uses the radio waves
such as a TV, VCR, or tape deck. (If the that share the same frequency as other
receiver is being used in combination with a wireless systems, such as wireless LAN or
TV, VCR, or tape deck, and is placed too Bluetooth, interference or poor transmission
close to that equipment, noise may result, may result. In this case, take the following
and picture quality may suffer. This is steps:
especially likely when using an indoor Do not install the system near other
antenna (aerial). Therefore, we recommend wireless systems.
using an outdoor antenna (aerial).) Do not use the system and the other
Use caution when placing the receiver on wireless systems at the same time.
surfaces that have been specially treated The transmission distance differs depending
(with wax, oil, polish, etc.) as staining or on the usage environment. Find a location
discoloration of the surface may result. where transmission between the S-AIR main
unit and sub unit is most effective, and
On operation install the S-AIR main unit and sub unit
there.
Before connecting other components, be sure
to turn off and unplug the receiver.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
103GB
There is no sound from one of the front
Troubleshooting speakers.
Connect a pair of headphones to the
If you experience any of the following PHONES jack to verify that sound is
difficulties while using the receiver, use this output from the headphones. If only one
troubleshooting guide to help you remedy the channel is output from the headphones, the
problem. component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
Audio receiver and the component. If both
channels are output from the headphones,
There is no sound, no matter which the front speaker may not be connected to
component is selected, or only a very the receiver correctly. Check the
low-level sound is heard.
connection of the front speaker which is
Check that the speakers and components not outputting any sound.
are connected correctly and securely. Make sure you have connected to both the
Check that all speaker cords are connected L and R jacks of an analog component, and
correctly. not only to either the L or R jack. Use an
Check that both the receiver and all audio cord (not supplied).
components are turned on.
Check that MASTER VOLUME is not set There is no sound from analog 2
to VOL MIN. channel sources.
Check that the SPEAKERS is not set to off Check that the INPUT MODE is not set to
(page 32). AUTO (page 85) and the DIGITAL
Check that headphones are not connected. connection is not made for the selected
Press MUTING on the remote to cancel input.
the muting function. Check that the INPUT MODE is not set to
Check that you have selected the correct AUTO (page 85) and the A. ASSIGN
component with the input buttons (page function is not used to reassign the audio
40). input of another source to the selected
When only a very low-level sound is input (page 85).
heard, check to see if NIGHT MODE is
activated (page 64). There is no sound from digital sources
The protective device on the receiver has (from COAXIAL or OPTICAL input jack).
been activated. Turn off the receiver, Check that the INPUT MODE is not set to
eliminate the short-circuit problem, and ANALOG (page 85).
turn on the power again. Check that the ANALOG DIRECT
function is not selected.
There is no sound from a specific
component. The left and right sounds are
Check that the component is connected unbalanced or reversed.
correctly to the audio input jacks for that Check that the speakers and components
component. are connected correctly and securely.
Check that the cord(s) used for the Adjust the level parameters using the
connection is (are) fully inserted into the LEVEL menu.
jacks on both the receiver and the
component.
104GB
There is severe hum or noise. Dolby Digital or DTS multi channel
Check that the speakers and components sound is not reproduced.
are connected securely. Check that the DVD, etc. you are playing
Check that the connecting cords are away is recorded in Dolby Digital or DTS
from a transformer or motor, and at least format.
3 meters away from a TV set or fluorescent When connecting the DVD player, etc., to
light. the digital input jacks of this receiver,
Move your audio components away from check the audio setting (the settings for the
the TV. audio output) of the connected component.
The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with Recording cannot be carried out.
alcohol. Check that the components are connected
correctly.
There is no sound, or only a very low- Select the source component using the
level sound is heard from the center/ input buttons (page 40).
surround/surround back speakers.
Select a CINEMA STUDIO EX mode There is no sound from the component
(page 63). connected to the DIGITAL MEDIA
Adjust the speaker level (page 39). PORT adapter.
Check SP PATTERN setting (page 50). Adjust the volume of this receiver.
The DIGITAL MEDIA PORT adapter
There is no sound from the subwoofer. and/or component is not connected
Check that the subwoofer is connected correctly. Turn off the receiver, then
correctly and securely. reconnect the DIGITAL MEDIA PORT
Make sure you have turned on your adapter and/or component.
subwoofer. Check the DIGITAL MEDIA PORT
Depending on the selected sound field, no adapter and/or component device to make
sound output from the subwoofer. sure it supports this receiver.
When all speakers are set to LARGE
and NEO6 CIN or NEO6 MUS is
selected, there is no sound from the
subwoofer.
Check SP PATTERN setting (page 50).
Video
continued
105GB
The image of the COMPONENT VIDEO Radio stations cannot be tuned in.
OUT is corrupted. Check that the antennas (aerials) are
Video input signals other than 480p connected securely. Adjust the antennas
component are not received when signals (aerials) and connect an external antenna
are output from the VIDEO jack. Input (aerial), if necessary.
480i component video signals. The signal strength of the stations is too
weak (when tuning in with automatic
Recording cannot be carried out. tuning). Use direct tuning.
Check that the components are connected Make sure you set the tuning interval
correctly. correctly (when tuning in AM stations
Select the source component using the with direct tuning).
input buttons (page 40). No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations). Preset the
Tuner stations (page 68).
Press DISPLAY repeatedly on the receiver
The FM reception is poor. so that the frequency appears on the
Use a 75-ohm coaxial cable (not supplied) display.
to connect the receiver to an outdoor FM
antenna (aerial) as shown below. If you RDS does not work.*
connect the receiver to an outdoor antenna Make sure that you are tuned to an FM
(aerial), ground it against lightning. To RDS station.
prevent a gas explosion, do not connect the Select a stronger FM station.
ground (earth) wire to a gas pipe.
The RDS information that you want
Outdoor FM antenna (aerial) does not appear.*
Contact the radio station and find out
whether they actually provide the service
Receiver in question. If so, the service may be
ANTENNA
AM temporarily out of order.
Ground (earth)
wire (not * Models of area code CEL, CEK only.
supplied)
To ground
106GB
No sound is output from the receiver
HDMI and TV speaker while using the System
Audio Control function.
The source sound input to the HDMI
jack is not output from the receiver or Make sure the TV is compatible with the
the TV speaker. System Audio Control function.
Check the HDMI connection (page 24). If the TV does not have System Audio
You cannot listen to the Super Audio CD Control function, set the AUDIO OUT
by connecting HDMI. settings in HDMI menu to
Depending on the playback component, TV+AMP if you want to listen to the
you may need to set up the component. sound from the TV speaker and receiver.
Refer to the operating instructions AMP if you want to listen to the sound
supplied with each component. from the receiver.
Be sure to use a connecting cable for the If you cannot listen to the sound of a
HDMI jack corresponding to high speed component connected to the receiver
(an HDMI version 1.3, category 2 cable) Change the input of the receiver to
when you view images or listen to sound HDMI when you want to watch a
during a Deep Color transmission. program on a component connected via
HDMI connection to the receiver.
The source image input to the HDMI Change the TV channel when you want
jack is not output from the TV. to watch a TV broadcast.
Check the HDMI connection (page 24). Select the component or input you want
Depending on the playback component, to watch when you watch a program on
you may need to set up the component. the component connected to the TV.
Refer to the operating instructions Refer to the operating instructions of the
supplied with each component. TV on this operation.
Be sure to use a connecting cable for the
HDMI jack corresponding to high speed
(an HDMI version 1.3, category 2 cable)
when you view images or listen to sound
during a Deep Color transmission.
107GB
No sound is heard from the S-AIR
S-AIR function product.
S-AIR connection is not established If you use another S-AIR main unit, place
(sound transmission is not it more than 8 m away from this S-AIR
established), e.g., the indicator of the main unit.
S-AIR sub unit turns off, flashes, or Confirm the S-AIR IDs of the S-AIR main
turns red. unit and S-AIR sub unit (page 79).
If you use another S-AIR main unit, place Confirm the pairing setting (page 80).
it more than 8 m away from this S-AIR Place the S-AIR main unit and S-AIR sub
main unit. unit closer to each other.
Confirm the S-AIR IDs of the S-AIR main Avoid use of equipment that generates
unit and S-AIR sub unit (page 79). electromagnetic energy, such as a
Another S-AIR sub unit is paired to the microwave oven.
S-AIR main unit. Pair the desired S-AIR Place the S-AIR main unit and S-AIR sub
sub unit with the S-AIR main unit (page unit separately from other wireless
80). devices.
The S-AIR main unit is paired to another Avoid using any other wireless devices.
S-AIR sub unit. Cancel pairing. Change the RF CHANGE setting (page
Place the S-AIR main unit and S-AIR sub 83).
unit separately from other wireless Change the S-AIR ID settings of the
devices. S-AIR main unit and S-AIR sub unit.
Avoid using any other wireless devices. Turn off the system and S-AIR sub unit,
The S-AIR sub unit is turned off. Make then turn on them.
sure the AC power cord (mains lead) is Check that headphones are not connected
connected and turn on the S-AIR sub unit. to the S-AIR sub unit.
No sound is heard from the S-AIR There is noise or the sound skips.
receiver. If you use another S-AIR main unit, place
Check that the components are connected it more than 8 m away from this S-AIR
to analog jack of this receiver. main unit.
Place the S-AIR main unit and S-AIR sub
unit closer to each other.
Avoid use of equipment that generates
electromagnetic energy, such as a
microwave oven.
Place the S-AIR main unit and S-AIR sub
unit separately from other wireless
devices.
Avoid using any other wireless devices.
Change the RF CHANGE setting (page
83).
Change the S-AIR ID settings of the
S-AIR main unit and S-AIR sub unit.
108GB
Remote commander If you are unable to remedy the
problem using the
The remote does not function.
troubleshooting guide
Point the remote at the remote sensor on
the receiver. Clearing the receivers memory may remedy
Remove any obstacles in the path between the problem (page 31). However, note that all
the remote and the receiver. memorized settings will be reset to their
Replace all the batteries in the remote with factory settings and you will have to readjust
new ones, if they are weak. all settings on the receiver.
Make sure you select the correct input on
the remote.
When you operate a programmed non-
If the problem persist
Sony component, the remote may not Consult your nearest Sony dealer. Note that if
function properly depending on the model service personnel changes some parts during
and the maker of the component. repair, these parts may be retained.
In the event of a problem with S-AIR function,
have a Sony dealer check the entire system
together (S-AIR main unit and S-AIR sub
Error messages unit).
PROTECTOR
Irregular current is output to the speakers, or
the upper panel of the receiver is covered
with something. The receiver will
automatically turn off after a few seconds.
Check the speaker connection and turn on
the power again.
Additional Information
109GB
Input
Specifications Analog Sensitivity: 500 mV/
50 kohms
S/N3) : 96 dB
Amplifier section (A, 500 mV4))
Models of area code CEL, CEK, AU, TW1) Digital (Coaxial) Impedance: 75 ohms
Minimum RMS Output Power S/N: 100 dB
(8 ohms, 20 Hz 20 kHz, THD 0.09%) (A, 20 kHz LPF)
85 W + 85 W Digital (Optical) S/N: 100 dB
Stereo Mode Output Power (A, 20 kHz LPF)
(8 ohms, 1 kHz, THD 1%)
Output (analog)
100 W + 100 W
AUDIO OUT Voltage: 500 mV/
Surround Mode Output Power2) 10 kohms
(8 ohms, 1 kHz, THD 10%)
SUBWOOFER Voltage: 2 V/1 kohm
140 W per channel
Equalizer
Gain levels 10 dB, 1 dB step
Models of area code TH1)
Minimum RMS Output Power 3) INPUT
SHORT (with sound field and equalizer
(8 ohms, 20 Hz 20 kHz, THD 0.09%) bypassed).
70 W + 70 W 4) Weighted network, input level.
110GB
Video section Supplied accessories
Inputs/Outputs Operating instructions (this manual)
Video: 1 Vp-p, 75 ohms Quick Setup Guide (1)
COMPONENT VIDEO: FM wire antenna (aerial) (1)
Y: 1 Vp-p, 75 ohms AM loop antenna (aerial) (1)
PB/CB : 0.7 Vp-p, 75 ohms Remote commander (RM-AAP044) (1)
PR/CR : 0.7 Vp-p, 75 ohms R6 (size-AA) batteries (2)
80 MHz HD Pass Through Optimizer microphone (ECM-AC2) (1)
Power consumption
Area code Power consumption
CEL, CEK, AU, TW, 240 W
TH
111GB
Index
Numerics H S
2CH STEREO 65 HDMI S-AIR 76
5.1 channel 16 connecting 24 Satellite tuner/Set-top box
7.1 channel 16 connecting 28
I Selecting
A Initial setup 31 component 40
AUTO CALIBRATION 32 INPUT MODE 85 sound field 63
AUTO FORMAT DIRECT speaker system 32
(A.F.D.) 60 M Sleep Timer 90
Menu Sound fields
B AUDIO 55 resetting 66
BI-AMP 51 AUTO CAL 37 selecting 63
Bi-amplifier connection 91 EQ 54 Speakers
Blu-ray disc player HDMI 56 connecting 17
connecting 27 LEVEL 49 installing 16
playback 43 S-AIR 58 Super Audio CD player
SPEAKER 50 connecting 22
C SURROUND 53 playback 42
SYSTEM 57 System Audio Control 75
Camcorder
TUNER 54 System Power Off 76
connecting 29
CD player VIDEO 56
connecting 22 Muting 41 T
playback 42 Test Tone 49
CD recorder N Tuner
connecting 22 Naming 38, 41, 70 connecting 30
NIGHT MODE 64 Tuning
D automatically 67
O directly 67
DIGITAL MEDIA PORT
to preset stations 69
connecting 88 One-Touch Play 75
TV
input 40
connecting 20
Dolby Digital 100 P
Dolby Digital EX 59 PAIRING 80
DTS 101
V
Phase Audio 49
DVD player VCR
Phase Noise 49
connecting 26 connecting 29
Video game
playback 43 R connecting 29
DVD recorder RDS 71
connecting 29 Recording
onto a CD-R 90
E onto a recording media
Error messages 109 91
Remote commander 11
(1)