Connect the functional earth (FE) connections of the 5 Commissioning, configuration and parameterisation Commissioning, configuration and parameterisation of Power supply connection1) CTEU-EP Pin allocation products connected via X1 and X2 to the earth potential the bus node depends on the higher-order control sys with a short conductor with the greatest possible cross tem. The basic approach and required configuration data 1 24 V Operating voltage PS UEL/SEN section (4 mm2 Cu). are explained in the following sections. Electronics/sensors (Power System) 4.4 Check the power supply 2 24 V Load voltage PL UVAL/OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning Valves/outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note (Power Load) Uncontrolled movement of the actuators, loose tubing, Functional testing undefined switching statuses of the electronics 3 0V Operating voltage PS UEL/SEN The PS LED lights up when operating voltage is ap Injury caused by moving parts, damage to machine and to system 4 0V Load voltage PL UVAL/OUT plied (within permitted range). Before commissioning, ensure that the connected 5 FE Functional earth FE The LED X1 or X2 lights up green if a product with I-Port products do not perform any uncontrolled move (Functional Earth) 2) interface is connected correctly ( 7). ments. 1) Plug connector M12, 5-pin, A-coded Observe commissioning notices in the control system 2) Secure connection to functional earth over the connected 4.5 Connecting to the network documentation. product 4.3 Potential equalisation Installation guidelines Operating instructions Festo AG & Co. KG No automatic checking of configuration and parame Original instructions Ruiter Strae 82 Network connections1) terisation: The bus node and the connected products Network protocol EtherNet/IP or 73734 Esslingen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning also go into operation if configuration is incorrect. Pin allocation TP1 2) TP2 2) Modbus TCP Germany 5.1 Switch on the power supply +49 711 347-0 1 TX+ RX+ Electric voltage If the control system and network participants have sep www.festo.com 2 RX+ TX+ Injury caused by electric shock, damage to machine arate voltage supplies, the following sequence is recom and to system 3 TX RX mended for switch-on: For the electrical power supply to all network parti 4 RX TX 1.Switch on the power supply to all network participants. cipants and other network components 2.Switch on power supply to control system. Housing Screening/functional earth (e.g.switches and routers), use only PELV circuits (Shield/Functional Earth) 3) IEC60204-1/EN60204-1. 5.2 Setting the DIL switch 8067817 [8067819] 1702a TX = transmitted data, RX = received data 1.Setting IP address 5.3. 1) 2 sockets M12, 4-pin, D-coded; observe installation guidelines 2.Perform additional settings Table, item 3...5. and line specification 4.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 1 Intended use 2) Pin activation with deactivated crossover detection Data transmission errors 1 2 3 4 5 The bus node type CTEU-EP is intended exclusively for use 3) Secure connection to functional earth over the connected product 4.3 Potential equalisation Malfunction as a participant in EtherNet/IP or Modbus TCP networks. If installation has not been carried out correctly and The bus node may only be used in its original status 3.2 Indicators high transmission rates are used, data transmission without unauthorised modifications and only in perfect Status LEDs1) errors may occur, e.g. as a result of signal reflections technical condition. Significance and attenuations. The specified limit values must be observed here. PS Status of the operating voltage supply (Power Connect screening to all network cables The product is intended for use in industrial environ System) Wherever possible, only ground screening once (star- Item DIL switch 1) Function ments. Outside of industrial environments, e.g. in com X1 Status of the internal communication between shaped) to prevent ground loops ON OFF mercial and mixed-residential areas, actions to suppress the bus node and the connected product Observe installation guidelines of the EtherNet/IP interference may have to be taken. NS X2 I-Port Device1 or I-Port Device22) user organisation (ODVA): www.odva.org DIL switch 1: NS Network status EtherNet/IP installation guidelines 1 1 ... 6: Host ID of the IP address, bit 0 ... 5 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note TP1 Observe port and cable specifications: Connection status Link1 or Link2 DIL switch 2: Comply with the legal rules and regulations and TP2 EtherNet/IP installation guidelines 1 1 ... 2: Host ID of the IP address bit 6 and 7 2) standards, rules of the testing organisations and Documentation on the control system 1) Additional information 7 2 insurance companies and national specifications 2) Accessories with two I-Port interfaces required to connect two 3.1, tableof network connections 3: Reserved applicable for the location. products, e.g. the decentralised electrical connection box CAPC Tableof line specifications 3 4: Network protocol ModbusTCP EtherNet/I P3) www.festo.com/catalogue 4 5: Status bytes Status informa No status inform 5.5 Table tion in the input ation in the input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note Connection Para image image 3) 4 Mounting, dismantling, installation meters Detailed information on commissioning is provided in Unauthorised access to the product can cause damage the documentation for the higher-order control system. or malfunctions. 5 6: Behaviour in case All outputs re All outputs are . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning When connecting the product to a network: of communication tain their last reset 3) Information on EtherNet/IP: errors and for switching status www.odva.org Protect the network from unauthorised access. control in the Uncontrolled movement of the actuators, loose tubing, Measures for protecting the network include: Idle-Mode Information on ModbusTCP: undefined switching statuses of the electronics www.modbus.org Firewall 1) Switch setting ON = ON, switch is to the left or on top Injury caused by moving parts, damage to machine and to system Information about products from Festo: Intrusion Prevention System (IPS) switch setting OFF = OFF, switch is to the right or underneath Before mounting and installation work: 2) Binary coding in ascending order from left to right 20, 21, 22, www.festo.com/sp Switch off the power supply. Network segmentation 3) Factory setting Switch off compressed air supply. Virtual LAN (VLAN) Vent the pneumatics. Virtual Private Network (VPN) 5.3 Setting IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note 4.1 Mounting the bus node Security at a physical access level (port security). Documentation of the control system EtherNet/IP, MODBUS, ROCKWELLAUTOMATION, To mount the bus node, a product with I-Port interface is Further information: STUDIO5000 are registered trademarks of the re required (I-Port Device), e.g. a valve terminal with I-Port Guidelines and standards for security in information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note spective trademark owners in certain countries. interface or the decentralised electrical connection box technology, e.g. IEC 62443, ISO/IEC 27001. CAPC. Observe the basic addressing rules for the allocation For all available product documentation An access password protects only against accidental of the IP address, e.g. with respect to the use of www.festo.com/pk changes. private or public address ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note Use of switches and routers Check that the IP address can be used in the automa Mounting of the bus node on the decentralised electric With use of the EtherNet/IP function QuickConnect: tion network. Training of specialized personnel al connection box CAPC assembly instructions Use only switches and routers that support Ensure that there is no duplication of IP addresses in The product may only be commissioned by trained spe cialists in control and automation technology who are 1.Check seal and sealing surfaces of the bus node and the QuickConnect. use. familiar with: product with the I-Port interface. Replace damaged Use only patch cable. Use DIL switches 1 for setting the addressing type or mounting, installation, operation and diagnostics of parts. Use of crossover cables for setting the host ID of the bus node. control systems, networks and fieldbus systems 2.Push the bus node onto the product carefully and When using patch cables and crossover cables in the The change of IP addressing in the bus node re the applicable regulations for accident prevention and without tilting and press up to the stop. same network: quires a corresponding update in the higher-or occupational safety 3.Gently tighten down the self-tapping screws, using Ensure that the crossover detection Auto-MDI/MDI-X der control system. the documentation for the product. existing threads. is activated in the control system Service 4.Tighten the screws. Tightening torque: 0.7 Nm 10 %. Deactivate EtherNet/IP function QuickConnect Examples Consult your local Festo repair service if you have any 4.2 Dismantling the bus node 5.8. Host ID = 05 Host ID = 38 technical problems. 1.Unscrew the screws. Cable specification 2.Pull the bus node off without tilting it. Cable Ethernet twisted pair cable, shielded 2 Safety instructions 4.3 Connecting the power supply (Shielded Twisted Pair, STP) 1 2 3 4 5 6 1 2 1 2 3 4 5 6 1 2 Prior to any assembly or installation work, switch off Transmission class Category 5 20 + 22 = 1 + 4 = 5 21 + 22 + 25 = 2 + 4 + 32 = 38 power supplies, disconnect the compressed air supply (Link Class) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warning Set IP address: Set IP address: and vent the pneumatics. 192.168.1.005 192.168.1.038 Cable diameter1) 6 ... 8 mm For the electrical power supply, only use PELV circuits in Electric voltage Wire cross section 0.14 ... 0.75 mm2; 22 AWG required for max. Dynamic addressing accordance with IEC60204-1/EN60204-1. Injury caused by electric shock, damage to machine connection length between network parti Observe the handling specifications for electrostatically cipants (End-to-end-Link) 1.Make sure there is a DHCP server (e.g. BOOTP DHCP and to system sensitive devices. server from Rockwell Automation) in the network. For the electrical power supply, use only PELV circuits Connection length2) Max. 100 m End-to-end-Link Use cover caps to seal unused connections to achieve 2.Set all switch elements for address setting DIL1 (1...6) in accordance with IEC60204-1/EN60204-1 1) When using plug NECUMSD12G4C2ET the required degree of protection. and DIL2 (1...2) to OFF. (Protective Extra-Low Voltage, PELV). 2) Corresponding to the specification for EtherNet/IP networks Always ensure that the connection technology being (EtherNet/I P installation guideline) www.odva.org 3.With Festo Field Device Tool (FFT) or EtherNet/IP Observe the general requirements IEC60204-1/ used has the required degree of protection. Object, activate the DHCP option. EN60204-1 of the PELV power circuits. Strain relief 4.Switch bus node off and back on. Use only voltage sources that ensure a reliable elec When mounting on a moving part of a machine: 3 Ports and displays tric separation from the mains network in accordance Saved addressing Provide the network cable with strain relief. with IEC60204-1/EN60204-1. 1.Set all switch elements for address setting DIL1 (1...6) 2 3 4.6 Ensuring the degree of protection and DIL2 (1...2) to OFF. Always connect all circuits for operating and load voltage supplies UEL/SEN and UVAL/OUT. 2.Set the IP address with the Festo Field Device Tool (FFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note or EtherNet/IP Object. Fuse protection 1 The bus node supplies operating and load voltage to the Short circuit 3.Switch bus node off and back on. 4 connected products via the I-Port interfaces X1 and X2. Malfunction or damage to the electronics Static addressing Secure operating voltage UEL/SEN and load voltage Use connection technology (interconnecting cables, 1.Set the first three octets of the IP address with the UVAL/OUT separately. push-in connectors, adapters) with the required Festo Field Device Tool (FFT) or EtherNet/IP Object. Take due account of the current consumption of con degree of protection, e.g. plug connector 2.With all switch elements for address setting DIL1(1...6) NECU-M-S-D12G4-C2-ET. and DIL2(1...2), set the fourth octet (Host-ID) of the IP 1 Network connections (network ports TP1/TP2, field nected products during design and protection of the Use cover caps to seal unused connections, e.g. cover address. bus interface) 3.1 power supply. cap ISK-M12 Accessories 3.Switch bus node off and back on. 2 DIL switch (with transparent cover) 5.2 Observe power rating of the power supply (no bus node-internal overload protection for the connected Mount cover of the DIL switches: Check seal, place 3 Status LEDs 3.2, 7 products) 11. cover and push it down, tighten screws. Tightening 4 Power supply connection (X0) 3.1. torque: 0.4 Nm 20 %. Ensure correct polarity (no bus node-internal reverse I-Port-interfaces polarity protection for the connected products). Do not remove sealing plug from underside of bus The I-Port interfaces (X1/X2) are located on the underside node. of the bus node. Only when mounting the bus node on the decentral ised electrical connection box CAPC: Replace sealing plug on underside of the bus node Assembly instructions CAPC. 5.4 Resetting IP addresses to the factory setting 5.7 Changing start addresses of inputs/outputs X1 and X2 Status of the internal communication General mechanical characteristics 1.Set all switch elements for address setting DIL1 (1...6) Documentation of the control system between the bus node and the connected product and DIL2 (1...2) to ON. In most cases, the control system handles the assignment I-Port Device1 or I-Port Device21) Vibration and shock resistance Severity level (SL)1) for wall or (in accordance with H-rail mounting 2.Switch bus node off and back on. of the input/output addresses and the diagnostic addres LED in Status and significance IEC/EN 60068)1) 3.Set IP address via dynamic addressing 5.3. ses. dicator Vibration (part 2-6) Wall: SG2; H-rail: SG1 Shock (part 2-27) Wall: SG2; H-rail: SG1 5.5 Configuration with Generic Ethernet Module 5.8 Setting up QuickConnect (QC) EtherNet/IP LED illuminated green: Continuous shock (part 2-27) Wall and H-rail: SG1 Integrate participants into the project and configure function Normal operating status Temperature range2) them Documentation of the control system I-Port Device 1 or 2 is connected correctly Storage/transpor t 20 +70 C Operating and load voltage are connected (within Operation 5 +50 C Documentation of the control system Activate QuickConnect in the control system. permitted range)2) Example with software STUDIO5000 from Activate QuickConnect via attribute 12 of the TCP/IP Corrosion protection The product is intended for in LED flashing green: door use in a typical industrial at ROCKWELLAUTOMATION: interface object (factory setting: deactivated). Status of diagnostics mosphere. Undervoltage at system or additional power supply Avoid condensation. Integration and configuration of the bus node Connection between the bus node and the I-Port can only take place as long as there is no online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note Device is OK Materials RoHS-compliant Housing PA reinforced connection to the controller Menu Commu With use of the EtherNet/IP function QuickConnect, LED illuminated red: Cover PA nications Go Offline Auto-Negotiation and Crossover detection (Auto-MDI/ I-Port Device is connected correctly, but the internal Fibre-optic cables PC communication is malfunctioning Threaded bushing M12 Brass, nickel-plated 1.In the Controller Organizer window in the I/O Config MDI-X) are not available. Assignment of the pins for After commissioning, I-Port Device removed Threaded bushing M3 Brass uration area, open the dialogue window Select Mod transmitted and received data at the TP2 connection is LED flashing red: Seals NBR ule Type with a click of the right mouse button on Eth crossed. Error in the bus node Screws Steel, galvanized ernet and with the context command New Module. Deactivate Crossover detection in the hardware con Dimensions 2.In the Catalog, select the module Generic Ethernet figuration of the network neighbour (Partner Port). Both LEDs illuminated orange: Width 40 mm Firmware update active Length 91 mm Module from the table. To simplify the search, limit the Set baud rate to 100 Mbit/s. Height 39 mm selection with the text filter. Activate full-duplex mode. Both LEDs flash orange Weight (bus node without cables 98 g 3.Click on Create to confirm the selection. Select interconnecting cable dependent on pin as To locate the bus node (module location), e.g. dur and sub-assembly) signment of network connection of product connec ing hardware configuration in the control system or The Module Properties dialogue window opens. for troubleshooting 1) Explanation of the severity level Table Explanation on ted to TP2: vibration and shock severity level 4.In the Name text field, enter a designation for the bus LED is off: 2) Connected products may only cover a less extensive temperat Crossover-cable with identical pin assignment of No product connected to the bus node node. ure range. the ports 5.In the Comm Format list field, select the data format: 1) Accessory with two I-Port interfaces required to connect two Patch-cable with different pin assignment of the products Power supply Data-SINT (standard) ports 2) This display only relates to the status of the load voltage if the Data - SINT - With Statusbyte with use of status connected product is monitoring the load voltage and reports its Operating voltage for bus node and connec bytes over a separate connection status to the bus node. ted products1) Data - INT with usage of Word-based devices, e.g. 5.9 Check network communication Nominal value 24 V DC Tolerance range 18 30 V DC2) analogue module NS Network status Load voltage for bus nodes and connected 6.Calculate the total size of the assigned address space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note LED Status and significance products 1) 7.Dependent on the I/O assignment for Input and display Tolerance range 18 30 V DC2) Functional test Output, input the following connection parameters. The LED NS is illuminated green (with faultless com LED illuminated green: Intrinsic current consumption at nominal op Normal operating status (online) erating voltage 24 V DC Typ. 65 mA Connection Parameters Instance Size1)2) munication between control system and bus node). from operating voltage supply for electron (internal electronics) Communication with the network is OK The LEDs TP1 or TP2 flash green ( 7). ics/sensors (UEL/SEN) Variable Assembly Length Inputs4) 101 Assigned LED flashing green: address Communication with the network is OK Power rating of operating and load voltage Variable Assembly Length Outputs 100 space power supplies1)3) 6 EtherNet/IP Objects IP address is assigned Connection is not configured Bus node on the connected product (e.g. Max. 4A Single Port Inputs 111 8 3) valve terminal) Object In Name Type LED illuminated red: Single Port Outputs 110 8 Bus node on the decentralised electrical Max. 2 A class stance No communication to the network (offline), e.g. connection box CAPC per I-Port Device4) Dual Port Inputs 121 16 3) through invalid bus address (example: address con 1h 1 Identity Object CIP flict) or baud rate Power failure buffering 10 ms Dual Port Outputs 120 16 LED flashing red: 1) Separate, external fuses are required for the operating and load 4h 5.5 Assembly Object Dual Port Inputs 131 32 3) Communication with the network disrupted, time-out voltage power supplies (no bus node-internal overload and po Connection Parameters larity reversal protection for the products connected via X1 detected (Bus time-out) Dual Port Outputs 130 32 and X2). 47h 1 Device Level Ring Object EtherNet/I P LED flashes orange: 2) The tolerance range is dependent on the connected products. Dual Port Inputs 141 64 3) To locate the connected product (module location), 3) Total power rating of operating and load voltage power supplies 48h 1 QoS Object e.g. during hardware configuration in the control Dual Port Outputs 140 64 PS and PL (residual current), maximum permitted current con system or for troubleshooting sumption of bus node and connected products 1) Calculate the total size in bytes of the assigned address space F5h 1 TCP/IP-Interface Object LED is off: 4) Total power rating of operating and load voltage power supplies 2) For Data - INT: Cut value in half PS and PL (residual current), maximum permitted current con 3) Increase value by 2 prefixed status bytes only if DIL switch F6h 1...2 Ethernet Link Object No network connection sumption per I-Port Device 2.5 = ON 5.2 64h 1...64 Discrete Output Byte Object CTEU TP1/TP2 connection status Link1 or Link2 Explanation on vibration and shock severity level 8.Optional: To use status bytes over a separate connec 65h 1...64 Discrete Input Byte Object LED Status and significance tion, input the following parameters. Vibration load display 67h 1...2 Diagnostics Object (Status Frequency range Acceleration Displacement Connection Parameters Instance Size bytes) LED illuminated green: [Hz] [m/s2] [mm] Normal operating status Status Input 103 2 68h 1...2 Slave Information Object Network connection is OK SL1 SL2 SL1 SL2 SL1 SL2 Status Output (Heartbeat) 254 69h 1 System Object Both LEDs, TP1 and TP2 flash green: 28 28 3.5 3.5 Data traffic 8 27 8 27 10 10 9.For Configuration, enter the following values: 6Ah 1...2 IPort Module Parameter Object 27 58 27 60 0.15 0.35 Assembly Instance=102 and Size=0 LED is off: 6Bh 1...2 Port Configuration Object 58 160 60 160 20 50 No network connected 10. Enter IP address of the bus node. 300h 1...2 ISDU Access Object1) 160 200 160 200 10 10 11. Click on Apply to accept the inputs. 12. Close the dialogue window with OK. 1) ISDU = Indexed Service Data Unit 8 Maintenance Shock load In the Controller Organizer window in the I/O Configur No special measures. Acceleration Duration Shocks per ation area, the bus node appears under Ethernet as a For detailed information on the objects www.festo. [m/s2] [ms] direction newly integrated participant. 9 Accessories com/sp User documentation: CTEU-EP Appendix SL1 SL2 SL1 SL2 SL1 SL2 www.festo.com/catalogue Using participant properties to operating instructions. 150 300 11 11 5 5 Documentation of the control system 10 Glossary Characteristic Feature 7 Diagnostics Continuous shock load Term/ Significance Acceleration Duration Shocks per dir Vendor Name Festo Corporation PS Status of the operating voltage supply abbreviation Vendor ID 26 = 1Ah (Power System) [m/s2] [ms] ection Device Type 12 = 0Ch LED Status and significance QuickConnect Operating mode of the bus node, guarantees a 150 6 1000 Product Code 6001 = 1771h fast connection after restart of the network parti display cipants. Major Revision 1 Status Current status of the bus node LED illuminated green: EtherNet/I P Network protocol in automation technology Normal operating status Network-specific characteristics Serial Number is displayed based on Industrial Ethernet (TCP/IP) for data Operating voltage is present (within the permissible interchange between a higher-order control sys Product Name CTEU-EP range) Network protocol EtherNet/I P or ModbusTCP tem (industry PC, PLC or IO Controller), network Input Size/Output Size 0 ... 64 bytes Load voltage is present (within permitted range)1) ModbusTCP participants and field devices (Field Devices/ Suppor ted protocols Cyclic data exchange AssemblyInstance Table Connection Paramet LED flashes green (flashing frequency: 1 Hz) Modules), e.g. valve terminals or drives Simple Network Management Protocol ers www.odva.org (SNMP) Operating voltage is below the required voltage Extended EtherNet/IP participant properties www.modbus.org Load voltage is below the required level1) Suppor ted functions QuickConnect (QC) Min. bus cycle time (Reques 1 ms Short circuit at the I-Port1) PLC Programmable logic controller, also designated Device Level Ring (DLR) ted Packet Interval, RPI) system controller or controller for short (Program Acyclic data access via Explicit Mes LED is off: mable Logic Controller, PLC) Connections Operating voltage is not present saging Total of all connections Max. 32 Operating voltage is below the voltage required for Address Conflict Detection (ACD) Exclusive Owner Max. 1 diagnostic functions Firmware update 11 Technical data Integrated Switch Input only Max. 32 1) This display only relates to the status of the load voltage if the System status via image table Listen only Max. 311) connected product is monitoring the load voltage and reports its status to the bus node. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note System-specific func Diagnostics information (system dia 1) Only with simultaneous connection Exclusive Owner or Input tions gnosis, undervoltage, communication only errors) Technical data for the connected products can be ob Web server (status of bus node and tained from the product documentation. connected products, serial number, 5.6 Configuration with device master file (EDS file) configuration) Electrical characteristics To simplify set-up of the CTEU-EP bus node, Festo makes Transmission techno Switched Fast Ethernet; a device description file (EDS) available www.festo. Degree of protection through IP65/IP671)2) logy Design 100BaseTX housing com/sp. Transmission rate 10/100 Mbit/s, full-duplex/half-duplex The EDS file contains all information required to integrate Protection against electric shock through the use of PELV circuits (protection against direct and (Protective Extra-Low Voltage) Bus cycle time (Reques 1 ms the CTEU-EP into the hardware configuration of your con indirect contact) ted Packet Interval, RPI) trol system. Network connections 2 x socket, M12, D-coded, 4-pin Disconnection of network Galvanically separated through connections for operating voltage transformer (up to 500 V) Crossover detection Auto-M DI/MDI-X1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Note power supply UEL/SEN Max. address volume 64 bytes I, 64 bytes O, CE mark3) (see declaration of con In accordance with EU EMC Dir Requirements inputs/outputs 66 bytes I (with status bytes) formity) www.festo.com ective The software for configuration of your control system 1) Only if QuickConnect is not active 1) Requirement: Bus node mounted completely, plug connector in supports import of EDS files. the plugged-in status or provided with cover cap. 2) Connected products may only satisfy a lower degree of protec tion. 3) The product is intended for use in an industrial environment. Outside of industrial environments, e.g. in commercial and mixed-residential areas, actions to suppress interference may have to be taken.