Академический Документы
Профессиональный Документы
Культура Документы
STANDARD 2553
Third edilion
1992-10-01
Reference number
IS0 2553:1992(E)
Contents
1 scope 1
3 General .._............._..................._.. 1
5.2 Relationship between the arrow line and the joint .__..__...._... 8
5.5 Position of the xymbol with regard to the reference line .._ 11
7 Complementary indications ,. 18
0 IS0 1992
All rights reserved. No part of this publication ~nay he reproduced or utilized in arjy fat m
or by any means, electronic or mechanical. including plroloc~,pviug ~1~1 microfiltn. wItho II
permissinn in wt itirq from the plMlstler.
International Organization for Starldardization
Case Postale 56 l CH-12 11 Genhve 20 l Swltzerlalncl
Printed in Switzerland
ii
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Annexes
. ..
Licensed to Petricio Industrial/Ivan Petricio III
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Foreword
This third edition cancels and replaces the second edition (IS0
2553:1984). which has been technically revised to include IS0 2553/DAD
1:1987.
1) To be published
welded, brazed and soldered and/or welding, hraz- The symbol shall not be taken to prejudge the pro-
ing and soldering procedtlres, rather than showing cess to be employed.
these indications on the drawings of the welded
parts. The elementary symbols are shown in table 1.
If there are no such instructions, the dimensions re- If the joint should not be specified but only be rep-
lating to the preparation of the edges lo be welded, resented that the joint will be welded. brazed or
brazed and solder-ed and/or welding, brazing and soldered. the following symbol shall be used:
soldering procedures cat1 be close to the symbol.
4 Symbols
--- - .-
__------- ______ ..__. ..___. __. -- ._..- _.--_- .._---- ____ _--.__ -.--. .-.--..---..------- - .-. __ ___--.-...- _..... --- --.-- __---
10 Fillet weld
12 Spot wf?ld
13 Seam weld
3
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
16 Edge weld
III
17 Surfacing
18 Surface joint
19 Inclined joint
20 Fold joint 3
c-
1) Butt welds between plates with raised edges (symbol 1) not completely penetrated are symbolized as square butt
welds (symbol 2) with the weld thickness s shown (see table5)
4.2 Combinations of elementary symbols table 2 and applications for symbolic representation
in table A.2.
When required. combinations of elementary symbols
can be used. NOTE 1 Table2 gives a collection of combinations of
elementary symbols for symmetrical welds. For the sym-
The elementary symbols are to be combined for holic representation the elementary symbols are arranged
symmetrically at the reference line (see tableA.2). For the
welding from bolh sides in such a manner arranging
use of symbols out of symbolic representation the sym-
the applicable elementary symbols symmetrical to
~_
bols may be represented without the reference line.
the reference line. Typical examples are given in
X - -... -- - .- ~--.-----.--..-.--__-
--- K
-.-.---.--...
.------.-.~.
Double-V butt weld with broad root face
x
----.--.---..-.--.---.--
-.--.
Double-U butt weld
NOTE 2 Although it is not forbidden to associate sev- f) Rernovable backing strip used
lMRl
eral symbols, it is better to represent the weld on a sep-
~-. .--_____-
arate sketch when symbolization becomes too difficult.
6
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Flat (flush) single-V butt weld with flat (flush) backing run
Single-V butt weld with broad root face and hacking run
-L
1)
V--.----.
l!ista
L
__.___
._~.-_-.-..-.----
_..______
--.--...--.
-.-_____
-----.-..--.----.--.--.---_-.-
_--..-.
..-...-............
_-_--
Fillet weld with smooth blended face
L!G
.-__ _.__ ---.----.. __--..
1) Symbol in accordance with IS0 1302; instead of this symbol the main symbol v-- can be used.
---- -- I___._-------
5 Position of the symbols on drawings The purpose of the following rules is to define the
location of welds by specifying
5.1 General
-- the position of the arrow line:
For symmetrical welds, the dashed line is unnecessary - Other side of the joint.
and should be omitted.
NOTE 5 The posilion of the arrow in these figures is
4 The thickness of lines for arrow line, reference line, chosen for purposes of clarity. Normally, it would be
symbol and lettering shall be in accordance with the placed immediately adjacent to the joint.
thickness of line for dimensioning in accordance with
IS0 128 and IS0 3098-1, respectively. NOTE 6 See figure 2.
2a
1 = arrow lint3
3 - welding symbol
The position of the arrow line with respect to the - shall be completed by an arrow head.
weld is generally of no special significance [see
figures 4 a) and 4 b)]. However, in the case of welds 5.4 Position of the reference line
of types 4, 6 and 8 (see table I), the arrow line shall
point towards the plate which is prepared [see fig- The reference line shall preferably be drawn parallel
ures 4c) and 4d)]. to the bottom edge of the drawing, or if impossible
perpendicular.
k r--.
__--...
___
-I-
_--.__-.-.
_
_ ._. _--- . .._ -_
~ --- --..--- - _--
-_
li-
-
KIT
/ --.- -1_/- . .._
al bJ
- --.__-- .---__-.-_
m---- -----
25
5.5 Position of the symbol with regard to the -- The symbol is placed on the dashed line side if
reference line the weld (weld face) is on the other side of the
joint [see figure 5 b)].
The symbol is to be placed either above or beneath
the reference line, in accordance with the following NOTE 7 In the case of spot welds made by projection
regulation: welding, the projection surface is to be considered as the
external surface of the weld.
----.,---
/v P=
For symmetrical welds only
--- -es
r f
01 70 be welded on b) To bo welded
the arrow side on the other side
Figure 6 -- Examples of the principle 6.2.4 In the case of plug or slot welds with bevelled
edges. it is the dimension at the bottom of the hole
which shall be taken into consideration.
/--@-
a5
-------- 300
r z-7
--------- 300
NOTE - For deep penetration of fillet welds, the dimensions are indicated as 5806 b, for example.
1 Butl weld
-- --
14
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
___-
Definition inscription
--- - -___
V
(see 6.2.1 and 6.2.2)
s : minimum distance from the silt-face of the part to the bottom of the
penetration. which cannot be greater than the thickness of the S II
thinner part.
(see 6.2.1)
SY
(see 62.1)
Z n nxl(e)
--__-
-..-.-.---..---..--._
Seam weld
Plug weld
(e)
Spot weld
(ej
Definition Inscription
--- -- -___ _-__-
(see No. 4)
(see No. 3)
(see 6.2.3)
k) : (see No. 4)
c 1-1 nxl (e)
71 :
(see 6.2.4)
c : width of slot
I :
11 : C nxl (el
e-
c : width of w&l
-~- _____.. -..-. -..- ..-..----...-.- -
I7 : (see No. 4)
n : diameter of hole
iz : (see No. 4)
(4 : spacing d 0 n(e)
d : diameter of spot
7 Complementary indications fork, at the end of the reference lilie remote from the
reference line.
Complementary indications may be necessary in
order to specify some other characteristics of welds. Figure 11 gives an example of its use
For example:
The list giving the correspondance between the
numbers and the process is given in IS0 4063.
7.1 Peripheral welds
-4 23
/---
Figure 11 - indication of welding process
---. -- -. .__.....__
---. -- The informailon for joints and the dimensions can
be supplemented by further information in the tail,
Figure 9 - Indication of peripheral weld in the following order:
process
process
is to be symbolized
/
by a number written between the two branches of a Figure 12 .- Reference information
111/ISO 5817-01
IS0 6947.PA/
IS0 2560-E 512 RR 22
I I 1
.Top view
lll/lSO 5817 DI
IS0 2560-E 51 2 RR 22
nxl(e)
/-a=--
_ - - _- __ ___. _-.
I
If-.
i. __.- -7.--__t-
.-^..-._.__-
Top view
c = widthofseamweld
Front view
r- __.-.
-._. __--...-----
7
Top view
kigzi-i%
Front view
Top view
L--J -
V (e)
-----..-*
b) Fusion- welded spot welds
Symbolic reprasent~tion
(~1 .= pitch
21
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Annex A
(informative)
Tables A.1 to A.4 give some exa mples of the use of symbols. The rep-es?ntations shown are given sirnply
explanation.
_--.. --
-A
1
2
-----..---
3 II
2 ---
a
Symbolization
either
---_----------___ -..-
Designation
Symbol
VO. Illustration
(Numbers refer
to table 1)
N)))
-
Single-V bult
weld q---
---_..~.
V
E
3
-.-_-
6
7
))))))
n-------.-
._-~
__
8
Single-bevel
weld
4
I/
butt
HNH
n---
-
9
---d
El
24 Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
---_---_ ----__--.___-_
Symbolization
either
-- --.-__--- -_I--
Table
---.
A.1 - Examples
--__-_____
of the use of elementary symbols (continued)
--~~---
Representation
~___
Designation
Symbol
No. Illustration
(Numbers refer
-
to table 1)
~-. -
Single-bevel butt
weld
V
4
Single-V butt
weld with broad
root face
Y
5
Single-bevel butt
weld with broad
root face
_--.-._. .__ -~
Single-U butt
weld
7
~ _ ____.-- ----..
---.--- ----._--
--~___- ----.- -_
Symbolization
--- ..~_ --.---.------.-...--.----...-.--.- - .-..-. -.--- .-...-.-.---. ..--..-.-...- ..--- -- ..---.-- ---- _____..____
either
--- .- ___-
-.--- ----
-- -----
Tahlo
. .IS
A I _
-1..
FY~~d~~
__ -... r.--
of the use of elementarv
-- _.-- --- .~ - I
svrnhnlc
- I-.-
/rndirlf~+)
,,,..,,V..,
Representation
Designation
Symbol
No. Illustration
(Numbers refer
to table 1)
15
Single-J butt
---
weld
17
Fillet weld
18
28
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Symbolization
Fillet weld
))))I))))))))))):
~JJlJJ1JJ)))))JJ:
------.
Symbolization
either
--. ----- --
----
----
--_---- __---- - ---- ..-.---....
_---
V
___ _______. ---_---- --.. --------
----
Tnhle
..I._ A 1 -
,... Fwamnltac of the USF! nf elemenfarv
-,......r.-- X. _..- --- -. -.-...-. --.. , svmbols
-,... --.- fcontirlued)
,--... .._._ -,
_ - - -
Representation
Designation
40. Symbol
Illustration
(Numbers refer
to table 1)
I
--. ____I -___._ ----_----
---
22
Plug weld
23
24
Spot weld
12
----
25
-.---.I---- ~ ----
Symbolization
either
----
u
----
----
B
----
----
~
Designation
Symbol
IO. illustration
(Numbers refer
to table 1)
-- --_-. .._
26
Seam weld
13
27
34
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Symbolization
___-.-._-_--. - -.---_--.--.--.--.-.------ -
either or
- ---_
Designation
Symbol
VO. Illustration -
(Numbers refer to -.
table 1) -- --
f_-.- 3.- -f-++-
---.-- ----_---
II 2
))))))))))))I
-----
welded from both sides
2-2
ILlI
3
))I~))))))))
---
EL!!
Single-V butt weld
v3
and backing run
4
779
3-9 )Ji))ll)~~l))
-----
7
)))
--
--__---_ . .. .._. ----.-_.-..------._-
_-_ ..~ ..- ..-- .._ ___- .._~
Double-V bull welt1
-
5 v3
(X welcl)
3 - 3
q
-_--
_.
-
__
-
.
36 Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Symbolization
either
---
------
.--...---.-._---.--- --.-.
__-.-
---
Illustration
6
Double bevel butt weld ---
---
---
---- --_-___-__
Symbolization
either or
--- --___
-- -
Tahls
.--.-
A 3 -
. ..I
F~nmnl~s
-r.I...r...-
nf rnmhinations
-. --...-._. -_.-..-
nf elemtwtnrv
-. -_- . ..-.._ -. ,
nvmhnlc
- ,...--.-
/rnnr/rtderfl
I-------,
-___- --__-
Representation
_-.-_-.--.---..----.-
13 Fillet weld
Symbolization
- --...-.-.....-...-......_
-.- ._--..-..-.-..-.--_-_--..--.--- -_---
either or
---.--- ~-
--
-
El
~--
Representation
- __--- ---
42
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
-___.-- ---
Symbolization
either or
___-__ --
--
n
6
x,
1))))1))))~Ju.i
__------..-.--..-..-.-.--.-.
..-.
8 V
lMRl ))))>))N)>
---
El
-- ----__-
Symbolization
either or
---- -_-_I__
--------
1 -+-+I+
LA
2 -4-4.
I3
El
46
Licensed to Petricio Industrial/Ivan Petricio
ANSI Store order #X265677 Downloaded: 6/12/2006 10:59:50 AM ET
Single user license only. Copying and networking prohibited.
IS0 2553:1992(E)
Symbolization
either or incorrect
_-
________._ --- -.--.---. ._-- -._-.--... -.-- .---.- . ..----.----- -----.----- _.__ --- .-.-..--- _---..--.- --- ..-. -..
not recommended
No. Illustration
--.-
.-_.
-
NOTE 1 When the arrow cannot poinl to a joint, symbolization cannot be us~ci.
-.--_----____
Symbolization
either or incorrect
not recommended
not recommended
---
c!
Annex B
(informative)
Guidance for converting drawings made in accordance with IS0 2553:1974 into the
new system in accordance with IS0 2553:1991
As an interim solution for converting old drawings made in accordance with IS0 2553:1974, Welds --- Symbolic
representafion on drawings, the following examples show acceptable methods. This shall, however, be con-
sidered as a provisional solution only during the change-over period.
For new drawings, the dual-reference line ____________ shall always be used.
------- as\300
-------
Z-7 300
r-
Figure B.l - Weld on arrow side
NOTE 8 When converting drawings made to one of the methods E or A in IS0 25X3:1974 into this new system, it is es-
pecially important for fillet welds to add the letter n or z in front nf that dimension as the use of dimensioning leg length
(2) or throat thickness (0) has been connected with the position of weld symbol on the reference line.
UDC 621.791:744.44:003.62
Descriptors: drawings, technical drawings, welded ioints, brazed and soldered joints, symbols, graphic symbols