configuration in iPASOLINK iX 2 NEC Corporation 2015 NEC Group Internal Use Only Firmware update Procedure (Current Bank Step-1) Go to Equipment Utility>>Update (Storage>>NE) Utility Switch on the maintenance mode and select Program file and click execute Select Main Card from drop down and click next.
3 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Current Bank Step-2) Browse the Firmware file 2.10.09 and click ok and start firmware upgrade.
4 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Current Bank Step-3) After completing the update of file click ok on the below message (F/W reset Control) appeared on screen
5 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Current Bank Step-4) Click ok on the warning appeared on screen .
6 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Uncurrent Bank Step-1) Again go to Equipment Utility>>Update (Storage>>NE) Utility Switch on the maintenance mode and select Program file and click execute Select Main Card from drop down and click next.
7 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Uncurrent Bank Step-2) Browse the Firmware file 2.10.09 and click ok and start firmware upgrade.
8 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update Procedure (Uncurrent Bank Step-3) After completing the update of file click on cancel.
9 NEC Corporation 2015 NEC Group Internal Use Only
Firmware update confirmation After updating firmware confirm from Equipment inventory information that both the banks are updated with 2.10.09
10 NEC Corporation 2015 NEC Group Internal Use Only
Prerequisites and Steps to be followed
1. 1.Laptop should have IPv6 support in TCP/IP setting.
2. Once FW is update sucessfully.Logout the NE from local login
IP 172.17.254.253.
3. Login via local login DHCP IPv6 http://[fe80::1:da50]
4. Configure IPv6 as per plan at near end and far end as per procedure in next slides.(3-18)
5. Check inband management setting as per the procedure.
11 NEC Corporation 2015 NEC Group Internal Use Only
LCT Login IP for IPv6
DHCP IPv6 LCT Login IP is http://[fe80::1:da50]
Login the NE using IP address as below: User Name: Admin Password:12345678
12 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (1/15) 1.Go to Equipment Setup>>Network Management Configuration>>Port /VLAN setting>>Click on Inband Management VLAN setting >>select Inband Management 1 used and put VLAN ID
13 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (2/15) 2) Go to LLDP Setting >>Click on setup and select Mainboard/Port 5 LLDP usage to used.
14 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (3/15) 3. Go to Bridge Setting>>Click Setup
15 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (4/15) 4.Select IP Stack mode to IPV6
16 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (5/15) 5. Select Global Address Auto configuration to manual put IP address as per plan and assign gateway as per plan. 6. Select interface as bridge 1
17 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (6/15) 7. Select Management VLAN usage to used and Management VLAN ID in Inband management 01
18 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (7/15) 8. Verify inband VLAN ID is configured on Port 5 (already present in partial config file)
19 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (8/15) 8. Go to User Account/Security Setting>>Security Management>>Service status Setting>>Click on no 1 and configure as below:- Community Name: private Access control 1(IPV6) Enable Source IP address 1 (IPV6):-Primary Server IPv6 address Prefix Length 1 (IPv6):128
20 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (9/15) 8. Go to User Account/Security Setting>>Security Management>>Service status Setting>>Click on no 2 and configure SNMP community for secondary server as below:- Community Name: private1 Access control 1(IPV6) Enable Source IP address 1 (IPV6):-Secondary Server IPv6 address Prefix Length 1 (IPv6):128
21 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (10/15)
9)Go to User Account/Security Setting>>Security Management>>Service status Setting>>Click on NTP .
22 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (11/15)
10) This window will appear. Enable NTP .
23 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (12/15) 11) After enabling NTP configure as follows:- 1)NTP Server Mode Disabled. 2)NTP Client Mode Unicast. 3)Stratum 4. 4) Click OK.
24 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (13/15)
12)Go to User Account/Security Setting>>Security Management>>Service status Setting>>NTP Server
Address>> Click on 1
25 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (14/15) 13)This window will appear and configure as follow: 1)IP Address(IP V6) : Server IP address. 2)NTP Version : 4 3)Poll Time : 1[h] 8[min] 16[sec] (4096[s])
26 NEC Corporation 2015 NEC Group Internal Use Only
IPv6 Management Setting (15/15)
14) Click on OK to complete the configuration.
27 NEC Corporation 2015 NEC Group Internal Use Only
FTP setting Security Management Go to Security Management >>Service status setting Click on FTP setting and set FTP :Always enable Max Session:3 .
28 NEC Corporation 2015 NEC Group Internal Use Only
SFTP Setting Security Management Go to Security Management >>Service status setting Click on SFTP setting and set SFTP :Always enable.
29 NEC Corporation 2015 NEC Group Internal Use Only