Академический Документы
Профессиональный Документы
Культура Документы
DESCRIPTION
The UTC8227 is the audio power amplifier with built-in
two channel developed for portable radio cassette tape
recorder with power ON/OFF switch.
FEATURES
*Wide operating supply voltage: Vcc=5~12V
*Low quiescent supply current
(Icc=21mA,typical,at Vcc=9V ,Vi=0)
*Output power
Po=2.50W/CH at Vcc=9V,RL=4ohm ,f=1kHz,Thd=10% HDIP-12
*Soft Clip
*Built-in Thermal shut-down protection circuit
*Stand-by Switch
TEST CIRCUIT
SW1 Vcc2
1000F
100F
Vcc1
1 12
Boot
3 strap 1
Input 1
100F
6 1000F Output 1
2
0.015F
NF1 45
5 RL
120
47F
30k
Ripple
9
47F
Boot
10 strap 2
100F
7 1000F Output 2
Input 2
NF2 11
45
0.015F
8 RL
120
47F
30k
TAB 4
Pre Power
GND
GND
ELECTRICAL CHARACTERISTICS
(Ta=25C,Vcc=9V,RL=4,Rg=600,f=1kHz,unless otherwise specified)
Characteristic Symbol Test Conditions Min Typ Max Units
Quiescent current Icc Vi=0 21 45 mA
THD=10%,RL=4 2.0 2.5 W
Output Power Po
THD=10%,RL=3 3.0 W
Total Harmonic Distortion THD Po=0.4W/CH 0.2 1.0 %
Gv1 Rf=120,Vout=0.775Vrms 43 45 47 dB
Voltage Gain
Gv2 Rf=0,Vout=0.775Vrms 56.5
Input Impedance Rin 30
Output Noise Voltage Vno Rg=10k,BW=20Hz~20kHz 0.3 1.0 mVrms
Ripple Rejection Ratio R.R Rg=600fripple=100Hz 52 dB
Cross Talk C.T Rg=600,Vout=0, f=1kHz 50 dB
Input Offset Voltage V7,8 30 60 mV
Standby Current Sw1:OFF 1 A
Vin=0 RL=4
12 ICCQ 12 Vcc2=5V 9V 0
Ta=25k RNF=120
Vcc1=9V
3 V10,V2, 3 -60
0 0 0.1 -80
0 3 6 9 12 15 0.01 0.1 1 10 1 2 3 4 5
10 10 10 10 10
ICCQ, DC Vout vs. Supply Voltage Voltage Gain vs. Frequency Ripple Rejection vs. frequency
100 20
Vin=0
Vcc=9V
Quiescent current (mA)
80 16 80 Vcc=9V 0
RL=4
Output Voltage (V)
Voltage Gain (dB)
40 8 40 -40
20 ICCQ 4 20 -60
0 0 0 -80
0 5 10 15 20 25 1 2 3 4 5 1 2 3 4 5
10 10 10 10 10 10 10 10 10 10
APPLICATION INFORMATION
1.Input Voltage
When the excessive signal is input, turning-up is produced in the clip waveform. The turning-up point is
Vin=300mVrms(Typical) at Vcc=9V,RL=4f=1kHz. Enough care must be taken for this phenomenon.
2.Power ON/OFF
There is power ON/OFF switch at pin 1. However output power is changed by pin 1 supply voltage when
pin1 supply voltage is not same pin 12 supply voltage, after referring to attached date, select pin 1 supply voltage.
3.Voltage Gain
The voltage gain can be changed by the external negative feedback resistor. When Rf=0, the Gain is equal
to 56.5dB.When Rf=120the Gain is equal to 45dB.
www.DatasheetCatalog.com