Вы находитесь на странице: 1из 4

This document is not an API Standard; it is under consideration within an API technical committee but has not received

all approvals required to become an API Standard. It shall not be reproduced or


circulated or quoted, in whole or in part, outside of API committee activities except with the approval of the Chairman of the committee having jurisdiction and staff of the API Standards Dept.
Copyright API. All rights reserved.

WI 2388 API Connections with Non-standard Casing Walls

Ballot Text

This Ballot would modify the API Spec 5B thread design Tables 6, 7, & 9 by specifying the allowable wall thickness ranges
so that when calculating connection performances for intermediate wall thickness, the proper selection of the appropriate
line of 5B thread design data for a particular connection will be assured. Footnotes for 5B Tables 6 & 7 have been
modified to reflect that grade M65 has been withdrawn (presuming the ballot for such in 5CT passes).

Below, proposed deletions are shown as stricken and new material proposed is underlined as per the tracked changes;
some additional information is given in comment boxes.

Additionally, the other part of this work item for Specification 5CT Tables C.1/E.1 a footnote e has been added as follows:

For casing with S, L and B connections, intermediate wall thicknesses are allowed in accordance with 8.2.
This document is not an API Standard; it is under consideration within an API technical committee but has not received all approvals required to become an API Standard. It shall not be reproduced or
circulated or quoted, in whole or in part, outside of API committee activities except with the approval of the Chairman of the committee having jurisdiction and staff of the API Standards Dept.
Copyright API. All rights reserved.

Table 6Casing Short-Thread Dimensions Comment [BC1]: This is


All dimensions in inches, except as indicated. See Figure 3. the table number in the 15th
(1) (2) (3) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) edition. The table number to
change to 1 in the 16th edition.
End of
Nominal Length: Total Length: Minimum
Pitch Pipe to Hand-
Weight End of Length: Face of Diameter Depth Length,
Specified No. of Length: Diameter Center of Tight
Size Major Thread Pipe to End of Coupling of of Full Crest
Pipe Wall Threads Effective at Hand- Coupling, Standoff,
Designation Diameter And Hand- Pipe to to Hand- Coupling Coupling Threads
Thickness Per in Threads Tight Power- Thread
Coupling Tight Vanish Tight Recess Recess from End
Plane Tight Tums
lb per ft Plane Point Plane of Pipe
Make-Up

D D4 L1 L2 L4 E1 J M Q q A Lca
4-1/2 4.500 9.50 0.205-0.223 8 0.921 1.715 2.000 4.40337 1.125 0.704 4-19/32 0.500 3 0.875
4-1/2 4.500 Others 0.224-0.250 8 1.546 2.340 2.625 4.40337 0.500 0.704 4-19/32 0.500 3 1.500
5 5.000 11.50 0.220-0.252 8 1.421 2.215 2.500 4.90337 0.750 0.704 5-3/32 0.500 3 1.375
5 5.000 Others 0.253-0.296 8 1.671 2.465 2.750 4.90337 0.500 0.704 5-3/32 0.500 3 1.625
5-1/2 5.500 All 0.244-0.304 8 1.796 2.590 2.875 5.40337 0.500 0.704 5-19/32 0.500 3 1.750
6-5/8 6.625 All 0.288-0.271 8 2.046 2.840 3.125 6.52837 0.500 0.704 6-23/32 0.500 3 2.000
7 7.000 17.00 0.231-0.271 8 1.296 2.090 2.375 6.90337 1.250 0.704 7-3/32 0.500 3 1.250
7 7.000 Others 0.272-0.362 8 2.046 2.840 3.125 6.90337 0.500 0.704 7-3/32 0.500 3 2.000
7-5/8 7.625 All 0.300-0.328 8 2.104 2.965 3.250 7.52418 0.500 0.709 7-25/32 0.433 3-1/2 2.125
8-5/8 8.625 24.00 0.264-0.303 8 1.854 2.715 3.000 8.52418 0.875 0.709 8-25/32 0.433 3-1/2 1.875
8-5/8 8.625 Others 0304-0.400 8 2.229 3.090 3.375 8.52418 0.500 0.709 8-25/32 0.433 3-1/2 2.250
9-5/8 9.625 All 0.312-0.395 8 2.229 3.090 3.375 9.52418 0.500 0.709 9-25/32 0.433 3-1/2 2.250b
9-5/8 9.625 All 0.312-0.595 8 2.162 3.090 3.375 9.51999 0.500 0.713 9-25/32 0.433 4 2.250c Comment [BC2]: Deleted
10-3/4 10.750 32.75 0.279-0.349 8 1.604 2.465 2.750 10.64918 1.250 0.709 10-29/32 0.433 3-1/2 1.625b because there is no short-
10-3/4 10.750 Others 0.350-0.595 8 2.354 3.215 3.500 10.64918 0.500 0.709 10-29/32 0.433 3-1/2 2.375b thread according to Spec 5CT
Table C.1/E.1 in P110, Q125
10-3/4 10.750 Others 0.350-0.595 8 2.287 3.215 3.500 10.64499 0.500 0.713 10-29/32 0.433 4 2.375c
11-3/4 11.750 All 0.333-0.489 8 2.354 3.215 3.500 11.64918 0.500 0.709 11-29/32 0.433 3-1/2 2.375b
11-3/4 11.750 All 0.333-0.489 8 2.287 3.215 3.500 11.64499 0.500 0.713 11-29/32 0.433 4 2.375c
13-3/8 13.375 All 0.330-0.514 8 2.354 3.215 3.500 13.27418 0.500 0.709 13-17/32 0.433 3-1/2 2.375b
13-3/8 13.375 All 0.330-0.514 8 2.287 3.215 3.500 13.26999 0.500 0.713 13-17/32 0.433 4 2.375c
16 16.000 All 0.375-0.495 8 2.854 3.715 4.000 15.89918 0.500 0.709 16-7/32 0.366 3-1/2 2.875
18-5/8 18.625 87.50 0.435 8 2.854 3.715 4.000 18.52418 0.500 0.709 18-27/32 0.366 3-1/2 2.875
20 20.000 All 0.438-0.499 8 2.854 3.715 4.000 19.89918 0.500 0.709 20-7/32 0.366 3-1/2 2.875d
20 20.000 All 0.438-0.635 8 2.787 3.715 4.000 19.89499 0.500 0.713 20-7/32 0.366 4 2.875e
Included taper on diameter, all sizes, 0.0625 in. per in.
a
Lc = L4 1.125 in. for 8 round thread casing
b
Applicable to coupling grades lower than P110
c
Applicable to coupling grades P110 and higher
d
Applicable to coupling grades lower than J55 and K55 H40
e
Applicable to coupling grades J55 and K55 and higher
This document is not an API Standard; it is under consideration within an API technical committee but has not received all approvals required to become an API Standard. It shall not be reproduced or
circulated or quoted, in whole or in part, outside of API committee activities except with the approval of the Chairman of the committee having jurisdiction and staff of the API Standards Dept.
Copyright API. All rights reserved.

Table 7Casing Long-Thread Dimensions Comment [BC3]: This is


All dimensions in inches, except as indicated. See Figure 3. the table number in the 15th
(1) (2) (3) (4) (45) (56) (67) (78) (89) (910) (1011) (1112) (1213) (1314) edition. The table number to
change to 4 in the 16th edition.
Length Total End of Length: Minimum
End of Length Pitch Pipe to Face of Hand- Length
Diameter Depth
No. of Specified Pipe Length: End of Diameter Center of Coupling Tight Full
Size Major of of
Threads Pipe Wall to Effective Pipe at Hand- Coupling, To Standoff Crest
Designation Diameter Coupling Coupling
per in. Thickness Hand- Threads to Tight Power- Hand- Thread Threads
Recess Recess
Tight Vanish Plane Tight Tight Turns from End
Plane Point Make-Up Plane of Pipe

D D4 L1 L2 L4 E1 J M Q q A Lca
1 19
4- /2 4.500 8 0.250- 1.921 2.715 3.000 4.40337 0.500 0.704 4- /32 0.500 3 1.875
0.337
5 5.000 8 0.235- 2.296 3.090 4.90337 0.500 0.704 5-3/32 0.500 3 2.250
3.375
0.500
5-1/2 5.500 8 0.275- 2.421 3.215 3.500 5.40337 0.500 0.704 5-19/32 0.500 3 2.375
0.415
6-5/8 6.625 8 0.288- 2.796 3.590 3.875 6.52837 0.500 0.704 6-23/32 0.500 3 2.750
0.475
7 7.000 8 0.317- 2.921 3.715 4.000 6.90337 0.500 0.704 7-3/32 0.500 3 2.875
0.540
7-5/8 7.625 8 0.328- 2.979 3.840 4.125 7.52418 0.500 0.709 7-25/32 0.433 3-1/2 3.000
0.625
8-5/8 8.625 8 0.352- 3.354 4.215 4.500 8.52418 0.500 0.709 8-25/32 0.433 3-1/2 3.375
0.557
9-5/8 9.625 8 0.352- 3.604 4.465 4.750 9.52418 0.500 0.709 9-25/32 0.433 3-1/2 3.625b
0.595
9-5/8 9.625 8 0.352- 3.537 4.465 4.750 9.51999 0.500 0.713 9-25/32 0.433 4 3.625c
0.595
20 20.000 8 0.438- 4.104 4.965 5.250 19.89918 0.500 0.709 20-7/32 0.366 3-1/2 4.125d
0.499
20 20.000 8 0.438- 4.037 4.965 5.250 19.89499 0.500 0.713 20-7/32 0.366 4 4.125e
0.635
Included taper on diameter, all sizes, 0.0625 in. per in.
a
Lc = L4 1.125 in. for 8 round thread casing
b
Applicable to coupling grades lower than P110
c
Applicable to coupling grades P110 and higher
d
Applicable to coupling grades lower than J55 and K55 H40
e
Applicable to coupling grades J55 and K55 and higher
Table 9Buttress Casing Thread Dimensions Comment [BC4]: This is
All dimensions in inches, except as indicated. See Figure 5. the table number in the 15th
edition. The table number to
(1) (2) (3) (34) (45) (56) (67) (78) (89) (910) (1011) (1112) (1213) (1314) (1415) change to 5 in the 16th edition.

End of End of
Total Minimum
Pipe to Pipe to Length: Hand-
Length: Length: Length,
Specified No. of Length: Length: Center of Center of End of Tight Diameter of
Size Major End of Pitch Face of Full Crest
Pipe Wall Threads Imperfect Perfect a Coupling, Coupling, Pipe to Standoff Counterbore
Designation Diameter Pipe to Diameter Coupling Threads
Thickness per in. Threads Threads Power- Hand- Triangle Thread In Coupling
Vanish to Plane from End
Tight Tight Stamp Turns
Point of Pipe
Make-Up Make-Up
D D4 g L7 L4 E7 J Jn E7 A1 A Q Lcb
1 15 1
4- /2 4.516 0.224-0.337 5 1.984 1.6535 3.6375 4.454 0.500 0.900 1.884 3- /16 /2 4.640 1.2535
5 5.016 0.253-0.500 5 1.984 1.7785 3.7625 4.954 0.500 1.000 1.784 4-1/16 1 5.140 1.3785
5-1/2 5.516 0.275-0.415 5 1.984 1.8410 3.8250 5.454 0.500 1.000 1.784 4-1/8 1 5.640 1.4410
6-5/8 6.641 0.288-0.475 5 1.984 2.0285 4.0125 6.579 0.500 1.000 1.784 4-5/16 1 6.765 1.6285
7 7.016 0.317-0.540 5 1.984 2.2160 4.2000 6.954 0.500 1.000 1.784 4-1/2 1 7.140 1.8160
7-5/8 7.641 0.328-0.625 5 1.984 2.4035 4.3875 7.579 0.500 1.000 1.784 4-11/16 1 7.765 2.0035
8-5/8 8.641 0.652-0.557 5 1.984 2.5285 4.5125 8.579 0.500 1.000 1.784 4-13/16 1 8.765 2.1285
9-5/8 9.641 0.352-0.595 5 1.984 2.5285 4.5125 9.579 0.500 1.000 1.784 4-13/16 1 9.765 2.1285
10-3/4 10.766 0.350-0.595 5 1.984 2.5285 4.5125 10.704 0.500 1.000 1.784 4-13/16 1 10.890 2.1285
11-3/4 11.766 0.375-0.489 5 1.984 2.5285 4.5125 11.704 0.500 1.000 1.784 4-13/16 1 11.890 2.1285
13-3/8 13.391 0.380-0.514 5 1.984 2.5285 4.5125 13.329 0.500 1.000 1.784 4-13/16 1 13.515 2.1285
16 16.000 0.438-0.495 5 1.488 3.1245 4.6125 15.938 0.500 0.875 1.313 4-13/16 7
/8 16.154 2.7245
18-5/8 18.625 0.435 5 1.488 3.1245 4.6125 18.563 0.500 0.875 1.313 4-13/16 7
/8 18.779 2.7245
20 20.000 0.438-0.635 5 1.488 3.1245 4.6125 19.938 0.500 0.875 1.313 4-13/16 7
/8 20.154 2.7245
Included taper on diameter: Sizes 13-3/8 and smaller 0.0625 in. per in.; Sizes 16 and larger 0.0833 in. per in.

NOTE 1 At plane of perfect thread length L7, the basic major diameter of the pipe thread and plug gauge thread is 0.016 in. greater than specified pipe
diameter D for sizes 13-3/8 in. and smaller and is equal to the specified pipe diameter for sizes 16 in. and larger.
NOTE 2 Hand-tight standoff A is the basic allowance for basic power make-up of the joint as shown in Figure 5; the 3/8 in. equilateral triangle stamp
located on the pipe at the length A1 from the end of the pipe facilitates obtaining the power make-up provided for by the hand-tight standoff A.
a
Pitch diameter on buttress casing thread is defined as being midway between the major and minor diameters.
b
Lc = L7 0.400 in. for buttress thread casing; within the Lc length, as many as 2 threads showing the original outside surface of the pipe on their crests for a
circumferential distance not exceeding 25 % of the pipe circumference is permissible; the remaining threads in the Lc thread length shall be full crested
threads.

Вам также может понравиться