Академический Документы
Профессиональный Документы
Культура Документы
i
WARNING
CAUTION
CAUTION
Make sure the voltage selector
swich(115V/230V) is set to the
appropriate setting before plug in
ii
Contents
1. Specification ..........................................................................................1
2. Front Panel .............................................................................................2
3. Rear Panel ..............................................................................................3
4. System Installation...................................................................................3
5. System Operation ...................................................................................4
6. Display Setup .........................................................................................5
7. Main Menu Setup ...................................................................................8
8. Camera Setup .........................................................................................8
9. Record Setup..........................................................................................10
10. Sensor Setup .........................................................................................12
11. Motion Setup ........................................................................................13
12. Network Setup .....................................................................................14
13. Audio Setup .........................................................................................16
14. Backup Setup .......................................................................................17
15. System Setup ........................................................................................18
16. Search Setup .........................................................................................23
17. Other Function .....................................................................................26
18. Cell phone monitoring .........................................................................26
19. AVPlayer Operation .............................................................................27
20. Web Operation .....................................................................................28
21. Default Setting .....................................................................................33
22. Recording Time Table ..........................................................................35
23. USB Compatibility ...............................................................................35
iii
1. Specification
Video Format NTSC PAL
Video Input 4CH Input / BNC
Audio Input 4CH Input / RCA
Video Output 2CH Monitor Output / BNC
Audio Output 1CH Output / RCA
640x480800x6001024x7681280x10241280x7201440x900
VGA Output
(OPTIONAL)
Alarm Input 4CH Alarm In
Alarm Output BuzzerRelay Out(1 CH N.O/ N.C)
Display Mode Full Mode, 4 Division, Circulate Auto Switcher
Display Resolution 720 x 480 720 x 576
Highest 720 x 480 720 x 576
Recording
Resolution Hight 720 x 240 720 x 288
Normal 352 x 240 352 x 288
Highest Max. 30 fps Max. 25 fps
Recording
High Max. 60 fps Max. 50 fps
frame
Normal Max. 120 fps Max. 100 fps
Compression Algorithm Modified H.264
Operating System Embedded Linux
Triplex Record / Playback / Network
Recording Mode Manual, Schedule, Event, Smart
Schedule Recording Full-Time, Motion, Alarm, No Recording
Status Indicator (LED) Power, Record
Alarm Trigger, Motion Trigger, Video Loss
Event Mode
Recording Duration: OFF1~30 sec.
Normal: x1 multiple speed
Fast Forward: x1/2 / x2 / x4 / x8 / x16 multiple speed
Playback Fast Rewind: x2 / x4 / x8 / x16 multiple speed
Move 1 image per push button at still image (STILL Controller):
Forward/ Backforward
Searching Function: Time / Event
Network Protocol TCP/IP / PPPoE / DHCP / SMTP / DDNS
Communication Protocol RS-485
HDD type SATA 3.5 * 2 pcs (Not include HDD)
Automatic Formatting by System
HDD Management
(Pre-Formatting Not Required)
Internal Communication Protocol
PTZ Control (PELCO P, PELCO D, MIKAMI)
RS-485 interface Control
Archiving USB 1.1/2.0
Firmware Update USB Host
Multi-Language English / Chinese / Others
FacePlate / IR Remote Controller/USB Mouse(optional) GUI /
Control Mode
LAN
Network Control IE Browser
Network Function Live Play / Playback/PTZ Control
Power Supply DC 12V/4.1A(AC100V~240V 50/60HZ)
Unit Dimension 430mm (W)x300mm (D)x 48mm (H)
Weight Unit Weight (3.5Kgs) (Hard Drive not included)
Ambient Temperature -5 ~ 45
1
2. Front Panel
Under the live viewing mode, press MENU to enter the Quick
MENU Menu.
Under the menu mode, press MENU to go to upper menu.
Under the live viewing mode, press the button to enter
playback mode.
Playback/Pause
Under the playback mode, press the button to pause the
playback.
Under the playback mode, press the button to stop the
Stop
operation or go to upper menu.
UP /
To move up or down of the selection setting in menu
Down
Master HDD Indicator The LED lights on when the master HDD is written.
Slave HDD Indicator The LED lights on when the slave HDD is written.
Under the live viewing mode, press the button to start/stop the
Auto Switching
auto switching function.
2
3. Rear Panel
5 6 7 9
1 2 3 4 8
7 ALARM, RS-485
4. System Installation
Connect BNC connector of Cameras to the video input of the DVR
Coaxial cable cat6 or the above is suggested.
DVR Network Cabling
Please connect HUB or IP swtich device to DVR LAN port by RJ-45 cable then make
sure the LED of LAN is lighting on.
(The DVR support Static IPPPPOE, DHCP. Please refer to the Network Setup )
Alarm I/OAlarm
Please refer to the external alarm installation.
(Please refer to the system setup)
Speed Dome Camera
Pelco DPelco P & MIKAMI speed dome protocol supported.
Power Supply
3
Please use the particular DC12V switch power adaptor which comes with DVR in the
box and plug into the power input of DVR in the rear panel. for installation. The DVR
will go into the live viewing mode after power on.
5. System Operation
There are three kinds of DVR control device: front panel, remote controller, and
mouse.
Mouse Operation
In live viewing mode, the right mouse click will open the Quick Menu.
In menu, right mouse click can go to Upper Menu.
In main menu, left mouse click can enter the Selected Item of the Sub-Menu.
In menu, double click left button of mouse can enter the Selected Item of the
Sub-Menu.
Use the mouse scroll wheel to adjust settings in menu.
Please refer to the for PTZ setup.
Remote Controller
Every button of remote controller is the same with front panels.
Mute UP MENU
4
Menu Operation Front Panel & Remote Mouse
Controller
Select Characters from Virtual [Up/Down/Left/Right] [Moving Cursor]
Keyboard
Input Characters [Enter] [Left Click]
Exit the Virtual Keyboard [MENU] [Right Click]
Menu Operation
The pen image icon, , means it has the sub-menu.
6. Display Setup
There are three kinds of screen display mode: Live, Auto Switching, PTZ.
LIVE mode
After bootup the DVR, the system will enter the live viewing mode.
There are four kinds of status icon: recording, Mmotion triggered, L
5
video loss,Aalarm triggered.
Status Icon
Quick Menu
6
(1)SelectSETUP (1)SelectSETUP
Enter the Main Menu (2)[ENTER] (2)[Left Click]
PTZ
Please understand the usage of the speed dome before set up thePTZ.
Before this setting, please go to PTZto setup first.
Auto Switching
Auto Switching starts in the order of CH1, CH2, CH3, CH4, Quad.
Please disable this function with the below operation:
7
Please press the [Auto Switching] on panel again.
Please press the [Quad Display] on Controller again.
Please press the [Left Click] on mouse again.
After changing settings, the system will ask the below question before you
exit the Main Menu.
8. Camera Setup
8
CHANNEL
CH1~CH4: Apply settings to the selected channel.
TITLE
Use the virtual keyboard to input the camera name.
DISPLAY
ON/OFF: Enable or disable the camera display.
BRIGHTNESS
Set the value from 0~50.
CONTRAST
Set the value from 0~50.
HUE
Set the value from 0~50.
SATURATION
Set the value from 0~50.
LOSS BUZZER DURATION
1~30 (seconds) / OFF: set time of the buzzer beeping for the video loss.
LOSS ALARM DURATION
1~30 (seconds) / OFF: set the alarm time for video loss.
PTZ
TYPE
Set PTZ model No.: PTC-301PTC-203STFUM 626JG_QG988FUM
622SDFUM 628 or OFF. If this function is activated, please must select
proper protocol type.
PROTOCOL
Select a PTZ protocol: PELCO PPELCO DMIKAMI or OFF.
ADDRESS
Set the PTZ address from 0~255.
BUADRATE
Set the PTZ Buadrate: 120024004800960019200.
SPEED
Set the PTZ speed from 1~10
TOUR TIME
Set the PTZ tour time from 3~30 seconds or OFF.
PRESET
If the tour time is ON, the system will activate the auto-tour of the camera
automatically.
9
Front Panel & Remote
Menu Operation Mouse
Controller
(1)[Enter] to select the preset
position [Mouse Scroll
Select the Preset Point: 1~20
(2)[Up/Down] for selection Wheel] 1
(3)[MENU] Exit
Zoom + [CH1] [Left Click] Z+
TILT OPPOSITE
ON/OFF: Enable or disable the up/down reversal of PTZ.
9. Record Setup
RESOLUTION
Set the recording resolution: Normal, High, Highest.
FRAME RATE
Set the Recording Frame and Smart Recording Frame for each channel.
There are two kinds of mode: Normal, Smart
Normal mode
1. The max. recording frame is 30fps in NTSC and 25fps in PAL for each
channel.
2. If the resolution setting is NORMAL, the total recording frame per second
of those 4 channels cannot exceed 120fps in NTSC and 100fps in PAL. If
the resolution setting is HIGH, the total recording frame per second of
those 4 channels cannot exceed 60fps in NTSC and 50fps in PAL. If the
resolution setting is HIGHEST, the total recording frame per second of
those 4 channels cannot exceed 30fps in NTSC and 25fps in PAL.
10
Smart mode
1. The max. smart recording frame is 30fps in NTSC and 25fps in PAL for
each channel.
2. If the resolution setting is NORMAL, the total smart recording frame of
those 4 channels cannot exceed 120fps in NTSC and 100fps in PAL. If
the resolution setting is HIGH, the total smart recording frame of those 4
channels cannot exceed 60fps in NTSC and 50fps in PAL. If the
resolution setting is HIGHEST, the total smart recording frame of those 4
channels cannot exceed 30fps in NTSC and 25fps in PAL.
3. The recording frame for each channel cannot exceed the smart
recording frame.
4. If the resolution setting is NORMAL or HIGH, the minimum recording
frame for each channel is 3fps. If the resolution setting is HIGHEST, the
minimum recording frame for each channel is 1fps.
5. In normal condition, the system will record the footage by using the
setting of Normal Mode; the smart recording mode will start when motion
or alarm has been triggered.
RECORD QUALITY
Set the record value from 1~10 for each channel. The higher value is the better
quality.
11
RECORD SCHEDULE
Time Table
12
CHANNEL
Apply settings to the selected channel (CH1~CH4).
TYPE
Set sensors to NORMAL CLOSE or NORMAL OPEN.
RECORD DURATION
The number indicates duration of the recording after triggered: 10, 15,,30
seconds or OFF.
BUZZER DURATION
The number indicates duration of the buzzer beeping after triggered: 1~30
seconds or OFF.
ALARM DURATION
The number indicates duration of the alarming after triggered: 1~30 seconds or
OFF.
EVENT POP UP
The number indicates duration of the full screen display after triggered: 1~30
seconds or OFF.
CHANNEL
Apply settings to the selected channel (CH1~CH4).
ENABLE
ON/OFF: enable or disable the motion detection.
SENSITIVITY
Set the sensitivity from 1~10. The highest value means the more sensitive.
RECORD DURATION
The number indicates duration of the recording after triggered: 10, 15,,30
seconds or OFF.
BUZZER DURATION
The number indicates duration of the buzzer beeping after triggered: 1~30
seconds or OFF.
ALARM DURATION
The number indicates duration of the alarming after triggered: 1~30 seconds or
OFF.
EVENT POPUP
The triggered channel will display in full screen after the motion has been
triggered. The number indicates duration of the fully display time: 1~30 seconds
or OFF.
13
MOTION AREA
(1)Moving arrow
(2)[ENTER] to select area
(3)[Up/Down/Left/Right] to
Select Motion Area [Drag-Left-Click]
select area
(4) [ENTER] to confirm or
[MENU] to cancel
Go to Upper Menu [MENU] [Right Click]
IP MODE
MODE
Select IP Mode: STATICDHCP
IP
14
STATIC: please use virtual keyboard to input IP address
DHCP: obtain an IP address by DHCP server.
NETMASK
STATIC: please use the virtual keyboard to enter the NetMask IP address.
DHCP: obtain an NetMask IP address by DHCP server.
GATEWAY
STATIC: please use the virtual keyboard to enter the gateway IP address.
DHCP: obtain an gateway IP address by DHCP server
PORT
Please use the virtual keyboard to input the port number.
DNS 1
Please use the virtual keyboard to input IPaddress of DNS1.
DNS 2
Please use the virtual keyboard to input the IP address of DNS1.
DDNS
SERVER
Select the DDNS SERVER: DYNDNSCCTVDVR or OFF.
HOST NAME
Please use the virtual keyboard to input the DDNS host name.
USER NAME
Please use the virtual keyboard to input the DDNS user name.
PASSWORD
Please use the virtual keyboard to input the DDNS password.
PPPOE
If the IP mode is set as DHCP, the system cannot enter the menu below.
ENABLE
ON/OFF: Enable or disable the PPPOE.
If the IP mode is set as DHCP, the system will disable automatically.
ACCOUNT
Please use the virtual keyboard to input the PPPOE account.
PASSWORD
Please use the virtual keyboard to input the PPPOE password.
MTU
Please use the virtual keyboard to input the PPPOE MTU
IP
After the PPPOE connection is successfully, it will obtain an IP address
automatically.
15
E-MAIL
The email-alert will inform receivers immediately by sending the email.
ENABLE
ON/OFF: Enable or disable the email function.
SERVER
Please use the virtual keyboard to input the mail server.
FROM
Please use the virtual keyboard to input the senders email address.
TO
Please use the virtual keyboard to input the receivers email address.
AUTHENTICAION
ON/OFF: if the authentication is necessary on this mail server, please select
ON.
SSL
ON/OFF: if the SSL connection is nessary on this mail server, please select
ON
USER NAME
Please use the virtual keyboard to input the user name of email server.
PASSWORD
Please use the virtual keyboard to input the password of mail server.
CHANNEL
Apply settings to the selected channel (CH1~CH4).
RECORD
ON/OFF: enable or disable the audio record.
MUTE
ON/OFF: enable or disable the mute function.
INPUT VOLUME
16
Set the value from 1~10.
OUTPUT VOLUME
Set the value from 1~10.
(1)Select STARTor
(1) Select STARTor END
END
(2) [ENTER] to setup (2) [Double Left Click] or [Left Click] to
(3) [Left/Right] to select setup
Set the
time field.
START/END time (3) [Moving Cursor] to select time field.
(4) [Up/Down] to adjust
(4) [Mouse Scroll Wheel] to adjust time
the time value
value
(5) [MENU] to exit
(5) [Right Click] to exit settings
settings
Calculate the (1) select the TOTAL (1)Select the TOTAL Size
TOTAL SIZE of SIZE
Backup (2)[ENTER] to calculate (2) [Double Left Click] to calculate
Enter Backup
[Playback] [Left Click]OK
Operation
Backup Operation
Backup device: USB Port (Host), DVD-RW.
17
Front Panel & Remote
Menu Operation Mouse
Controller
choose the storage
[Left/Right] [Mouse Scroll Wheel]
device
Start to Backup [Enter] [Left Click]OK
CD Format(Backup
[Rewind] [Left Click]
Device: USB)
Complete and Exit the
[MENU] or [Stop] [Right Click]
Backup
18
SYSTEM INFO
LOG LIST
Event Table
REC OFF Record OFF
NORMAL REC Normal Record
MOTION REC Motion Record
SENSOR REC Sensor Record
MANUAL REC Manual Record
SCHEDULE REC Schedule Record
MOTION EVENT Motion Event
SENSOR EVENT Sensor Event
VIDEO LOSS Video Loss
NET CONNECT Network Connection
NET PLAYBACK Network Playback
NET DOWNLOAD Network Download
NET PTZ Network PTZ Operation
NET CLOSE Network Close
HD OVERWRITE Hard Disk Overwrite
RECOVERY Recovery
SHUTDOWN Shutdown
UNKNOWN ERR. Unknown Error
19
BOOT Boot
CHANGED CFG. Change the Users Configuration
PTZ CFG. Change PTZ Configuration
WATCHDOG Activate WATCHDOG
DISK ERROR Disk Error
HD NOT EXIST Hard Disk Not Exist
HD FORMAT Hard Disk Format
ERROR Error
SYS System
CH1 Channel 1
CH2 Channel 2
CH3 Channel 3
CH4 Channel 4
HD1 Hard Disk 1
HD2 Hard Disk 2
REC Record
ENC Encode
DEC Decode
TIME SET
The system time setup. Before exit the TIME SET, the system will ask whether to
chang the time settings or not.
USER MANAGEMENT
Set the DVR users and password. (The username and password is for
accessing DVR via IE browser.)
If the system has set password for adminthe system will ask you to keyin the
password before you go into the Quick Menu.
20
TYPE
The default is admin. Users are 1~3.
USER NAME
Please use the virtual keyboard to input the user name.
PASSWORD
Please use the virtual keyboard to input password. The default is no
password.
BUZZER
BUZZER ENABLE
ON/OFF: enable or disable the buzzer beeping. The default is ON.
When this buzzer is set OFF, it will not disable the buzzing function whenever
the video loss, motion, sensor, watchdog and no HDD occur.
OVERWRITE ENABLE
ON/OFF: Enable or disable buzzer beeping. The default is ON.
FORMAT HDD
Choose the HDD that you want to format.
NoteWhen the DVR system is activated, it will detect two hard disks. If the
data conflict exists between the both hard discks or time inconsistency is
between hard disks and DVR system, it will request to format the hard disks.
After the hard disk is choosen, the system will ask whether to format the hard
disk or not.
FIRMWARE UPGRADE
Please download the new firmware and copy to the USB memory stick and then
insert the memory stick to the USB port on front panel of DVR. After that,
please select this function.
Note: the DVR only can be upgraded by the USB Host. During the upgrading,
please dont operate the system or remove the USB stick while is in upgrading,
otherwise it will cause serious syste errors. After upgrading, the DVR will reboot
and restore the sytem as factory default.
SCREEN
BORDER COLOR
Border Color: black or white.
OSD ADJUSTMENT
Adjust the OSD position.
USER CONFIG
LANGUAGE
OSD Language Selection: English, Traditional Chinese, Simpilified Chinese.
TIME SEARCH
23
(1)[Double Left Click] or
[Left Click] to setup
(1) [ENTER] to setup (2) [Moving Cursor] to
(2) [Left/Right] to select time select time field.
Time Set of field.
SEARCH (3) [Up/Down] to adjust (3) [Mouse Scroll
time value Wheel] to adjust time
(4) [MENU] to exit settings value
(4) [Right Click] to exit
settings
Search & Playback [Playback] [Left Click]OK
EVENT SEARCH
Playback Operation
24
Front Panel &
Menu Operation Mouse
Remote Controller
Rewind [Rewind] [Left Click]
Fast Forward [Forward] [Left Click]
Rewind one Frame [Left] [Left Click] |
Forward one Frame [Right] [Left Click] |
Normal Playback 1x [Playback] [Left Click]
Pause [Pause] [Left Click]
Fast Forward [Stop] [Left Click]
Time Set of Backup [Enter] [Left Click]
CH1 Display [CH1] Double Left Click on the CH1
CH2 Display [CH2] Double Left Click on the CH2
CH3 Display [CH3] Double Left Click on the CH3
CH4 Display [CH4] Double Left Click on the CH4
Quad Display [Quad] Double Left Click on the full screen
25
Menu Operation Front Panel & Remote Mouse
Controller
START time setup [Up] [Left Click]
Please click to install. Then, if it has already installed the AVPlayer previously,
the system will ask whether to replace the old program or not.
After complete the installation, the system will execute the AVPlayer.
Note: If the system doesnt install the program automatically, please execute the
run.bat in the directory of storage device
User Interface
27
Open File Click
Fast Rewind Click
Rewind 1x Click
Pause Click
Playback 1x Click
Fast Forward Click
Capture the Image (Snap
Shot) to the Local Computer Click
Volume Control Drag
Minimize Window Click
Exit Click
Use the right click on mouse to open the
pop-up menu as below:
System Requirement
OSWindows 2000XPVista.
Web BrowserInternet Explorer
Install Add-ons
When you access DVR via IE browser, the system will ask the ID and password
before login. Then, please input the ID and password of the DVR; the default ID
and Password are admin and empty respectively.
If you were the first time to enter the web page, the browser will ask you to install
the add-ons
28
Choose to install add-ons
User Interface
Live
29
Play/Stop Live View Click
Click to start/stop record(Please set the save
Record to the Local Computer
path in the SETTING/INFO)
Snapshot image to local Click to snapsnot image (Please set the save
computer path in the SETTING/INFO)
Under the live view, click to enable the audio
Enable or disable audio or click to disableunder the quad display, it
doesnt offer the sound effect.
CH1 full screen display. Click
CH2 full screen display. Click
CH3 full screen display. Click
CH4 full screen display. Click
Quad display Click
Playback
30
Search
31
computer in the SETTING/INFO)
PTZ
Setting / Info
32
SnapSot Save Path Type a path in the text box then click to save.
Video Save Path type a path in the text box then click to save
Download the User
Manua Click to download
User Type
Manageme User Name Admin
nt
Passward
Buzzer Enable ON
Overwrite
ON
Hard Disk Enable
Setup Format
HDD
F/W
Upgrade
Border
Screen White
Color
34
Auto
OFF
Switching
XGA
800x600
Resolution
OSD
Adjustment
[ 3(5), 1(1) ]
(Vertical,
Horizontal)
Load Setup
Default
User
Save
Config
Config to
USB
Language English