Академический Документы
Профессиональный Документы
Культура Документы
Operating data
Requested flow rate 900.00 m/h Actual flow rate 900.00 m/h
Requested developed head 30.00 m Actual developed head 30.00 m
Pumped medium Water, rainwater Efficiency 84.6 %
with strainer Power absorbed 86.77 kW
Not containing chemical and Pump speed of rotation 1477 rpm
mechanical substances which Max. power on curve 93.10 kW
affect the materials Shutoff head 49.41 m
Ambient air temperature 20.0 C Design Single system 1 x 100 %
Fluid temperature 20.0 C
Fluid density 998 kg/m
Design
Design Close-coupled submersible Impeller type Multivane radial flow impeller
Orientation Vertical (K)
Suction flange pump drilled unmachined Wear ring Casing wear ring
according to(DN1) Impeller diameter 362.0 mm
Discharge flange pump drilled DN 200 / PN 10 / Drilled Free passage size 80.0 mm
according to(DN2) according to EN 1092-2 Direction of rotation from drive Clockwise
Shaft seal 2 mech. seals in tandem Temperature sensor PT100 With
arrangement with oil reservoir inboard
Manufacturer KSB Color Ultramarine blue (RAL 5002)
Type MG KSB-blue
Material code SIC/SIC/NBR
Driver, accessories
Driver type Electric motor Number of poles 4
Model (make) KSB Starting mode Direct/Star-delta possible
Motor const. type KSB Sub. motor Connection mode Delta
Frequency 50 Hz Motor cooling method Surface cooling
Rated voltage 400 V Motor version U
Rated power P2 95.00 kW Cable design Rubber hose
Available reserve 9.49 % Cable entry Sealed along entire length
Rated current 186.0 A Power cable S1BN8-F 4G25
Starting current ratio 6.3 Number of power cables 2
Insulation class H according IEC 34-1 Control cable S1BN8-F 10G1.5
Motor enclosure IP68 Number of control cables 1
Cos phi at 4/4 load 0.81 Moisture sensor With
Motor efficiency at 4/4 load 91.3 % Cable length 10.00 m
Temperature sensor Bimetal switch 2x
Motor winding 400 / 690 V
Data sheet
Materials G
Notes O-Ring (412) Nitrile rubber NBR
General criteria for a water analysis: pH-value >= 7; chloride Casing wear ring (502.1) Grey cast iron EN-GJL-250
content (Cl) <=250 mg/kg. Chlorine (Cl2) <=0.6 mg/kg. Shaft protecting sleeve (524) Chrome steel 1.4021+QT800
Pump casing (101) Grey cast iron EN-GJL-250 Motor housing (811) Grey cast iron EN-GJL-250
Discharge cover (163) Grey cast iron EN-GJL-250 Motor cable (824) Chloroprene rubber
Shaft (210) Chrome steel 1.4021+QT800 Screw (900) CrNiMo steel A4
Impeller (230) Grey cast iron EN-GJL-250
Bearing bracket (330) Grey cast iron EN-GJL-250
Nameplates
Nameplates language International Duplicate nameplate With
Installation parts
Installation type Stationary with guide wire Type Chain
Scope of supply Pump with installation parts Material CrNiMo steel 1.4404
Installation depth 4.50 m Length 5.00 m
Material concept G Max. load 1250 kg
Duckfoot bend
Size DN 200
Flange design EN
Duckfoot bend size (DN2 / DN 200 Drilled according to
DN3) EN
Material Grey cast iron EN-GJL-250
Mounting type Composite anchor bolts
Foundation rail Without
Claw
Design straight
Size DN 200
Qmin
Materials G
Notes
Total developed head
Qmin
50 Pump casing (101) Grey cast iron EN-GJL-250
Qmin
Discharge cover (163) Grey cast iron EN-GJL-250
408.0/A01
Shaft (210) Chrome steel
[m] 1.4021+QT800
362.0/A01
Impeller (230) Grey cast iron EN-GJL-250
300.0/A01
0
Operating data
0 500 [m/h] 1000 1500
Pumped medium Water, rainwater
20
with strainer
NPSH req.
Claw
Size DN 200
Lifting chain / -rope Chain
Material CrNiMo steel 1.4404
Length / Max. load 5.00 m / 1250 kg
Performance curve
Qmin
60
Qmin
Total developed head
40
Qmin
[m] 408.0/A01
20 362.0/A01
300.0/A01
0
0 200 [m/h] 400 600 800 1000 1200 1400
18
[m]
NPSH req.
10
2
0 200 [m/h] 400 600 800 1000 1200 1400
100
[%]
Efficiency
50
0
0 200 [m/h] 400 600 800 1000 1200 1400
100
Power Input
[kW]
50
Curve data
Speed of rotation 1477 rpm Efficiency 84.6 %
Fluid density 998 kg/m Power absorbed 86.77 kW
Viscosity 1.00 mm/s NPSH req. 3% 8.31 m
Flow rate 900.00 m/h Curve number K43185s
Requested flow rate 900.00 m/h Effective impeller diameter 362.0 mm
Total developed head 30.00 m Acceptance standard Tolerances to ISO 9906
Requested developed head 30.00 m Class 3B; below 10 kW
acc. to paragraph 4.4.2
Speed curve
60
Qmin
Total developed head
40
[m]
20 1477 1/min
0
0 200 [m/h] 400 600 800 1000 1200
18
[m]
NPSH req.
10
2
0 200 [m/h] 400 600 800 1000 1200
100
[%]
Efficiency
50
0
0 200 [m/h] 400 600 800 1000 1200
100
Power Input
[kW]
50
Curve data
Fluid density 998 kg/m Total developed head 30.00 m
Viscosity 1.00 mm/s Requested developed head 30.00 m
Flow rate 900.00 m/h Effective impeller diameter 362.0 mm
Requested flow rate 900.00 m/h
Motor data sheet
Motor data
Motor manufacturer KSB Starting mode Direct/Star-delta possible
Motor size 95N Power cable S1BN8-F 4G25
Motor construction type KSB Sub. motor Number of power cables 2
Motor material Grey cast iron EN-GJL-250 Power cable min. 26.8 mm
Efficiency class not classified Power cable max. 28.8 mm
Rated voltage 400 V Control cable S1BN8-F 10G1.5
Frequency 50 Hz Number of control cables 1
Motor power 95.00 kW Ctrl. cable diameter, min. 15.9 mm
Rated current 186.0 A Ctrl. cable diameter, max. 16.9 mm
Rated speed 1475 rpm Cable standard VDE
Starting current ratio 6.3 Switching frequency 10.00 1/h
Curve data
The no-load point is not a guarantee point within the meaning of IEC 60034
Load 0.0 % 25.0 % 50.0 % 75.0 % 100.0 %
P2 0.00 kW 23.75 kW 47.50 kW 71.25 kW 95.00 kW
n 1500 rpm 1494 rpm 1487 rpm 1481 rpm 1475 rpm
P1 4.59 kW 27.90 kW 52.20 kW 77.60 kW 104.00 kW
I 80.2 A 93.0 A 115.0 A 146.0 A 186.0 A
Eta 0.0 % 85.1 % 91.0 % 91.8 % 91.3 %
cos phi 0.08 0.43 0.66 0.77 0.81
Motor data sheet
1500
[rpm]
n
1470
0 10 [kW] 20 30 40 50 60 70 80 90 100
P1
200 100 1.0 100
eta
80 0.8 80
150
cos phi
60 I 0.6 60
100
40 0.4 40
[A]
0 0 0.0 0
0 10 [kW] 20 30 40 50 60 70 80 90 100
mechanical power P2
Installation plan
60
85
1214
10
1060 5
275
835
1707
(Lifting bail optional)
1982
233
1) DN3
400
min750 660
DN1
125
216
18
1) Minimum water level t1
340
1384
450
410
735 min 850 300
Access opening
min 1200
Motor Connections
Motor manufacturer KSB Suction flange pump drilled unmachined
Motor size 95N according to(DN1)
Motor power 95.00 kW Duckfoot bend size (DN2 / DN 200 Drilled according to
Number of poles 4 DN3) EN
Speed of rotation 1475 rpm
Weight net
Pump, Motor, Cable 1179 kg
Claw / Foot 30 kg
Total 1209 kg
Connect pipes without stress or strain! For auxiliary connections see
Dimensional tolerances for shaft axis height: DIN 747 separate drawing.
Dimensions without tolerances, middle tolerances to: ISO 2768-m
Connection dimensions for pumps: EN735
Dimensions without tolerances - welded parts: ISO 13920-B
Dimensions without tolerances - gray cast iron parts: ISO 8062-CT9
Connection plan