Академический Документы
Профессиональный Документы
Культура Документы
SM01-02-01
SERIVEC MANUAL
MODEL: DIG-610
(PORTABLE X-RAY UNIT)
* ALL THE INFORMATION PRESCRIBED INSIDE THE MANUAL IS PRESENTED ONLY AS A GUIDE FOR THE OPERATION
OF OUR PRODUCTS. AND IT MAY BE CHANGED WITHOUT PRIOR NOTICE.
* DONGMUN CO., LTD.: 717-HO, UNITECHVIL B/D, 1141-2, BAEGSUK-DONG, ILSAN-GU, KOYANG CITY, SOUTH KOREA
TEL: 82-31-907-7222, FAX: 82-31-904-2231,E-MAIL: dongmun@kita.net, URL: dong-mun.co.kr
Service Manual DIG-610
CONTENTS
1 Notice ----------------------------------------------------------------------- 27
2 Operation Sheet ----------------------------------------------------------------------- 27
3 Block Diagram ----------------------------------------------------------------------- 28
4 Calibration Process ----------------------------------------------------------------------- 29
5 Calibration Code and Data ----------------------------------------------------------------------- 33
6 Error code & Countermeasure ----------------------------------------------------------------------- 33
7 Schematics ----------------------------------------------------------------------- 34
8 Maintenance ----------------------------------------------------------------------- 40
TABLES
1 mA Calibration Code ----------------------------------------------------------------------- 33
2 Filament Preheat Calibration ----------------------------------------------------------------------- 33
3 Technical guide ----------------------------------------------------------------------- 41
2
Service Manual DIG-610
1. NOTICE
1.1. If the output calibration is needed after periodical inspections or repairs, please observe following
rules and methods.
CAUTION
The ionized radiation is dangerous for the operator if the following
safety measures are not strictly observed.
1.2. This manual is designed to ensure correct use and operation of DIG-610. Please read all the lines
thoroughly before you use this equipment.
1.3. Incorrect use and operation exceeding described conditions in this manual may occur damage of
the machine and shorten its life. Particular attention must be paid to all the warnings, cautions and
notes incorporated herein.
1.4. This equipment should be used only by the legally qualified persons and practitioners.
1.5. Regarding the AC cable and software, only the one developed and supplied by Dongmun should
be used.
1.6. No responsibility is taken by Dongmun for any infringement of patients or other rights of the third
parties which many results from the use of this manual.
1.7. Always keep the manual at hand for your reference.
2. OPERATION SHEET
3
Service Manual DIG-610
3. BLOCK DIAGRAM
READY
1
PXP60HF-CTL-001
CON1 3V/35mA
2
X-RAY LASER POINTER
HAND SWITCH
3
35312-03
CONTROL BOARD CON2 1
2 * EXPORT : NORMAL
* DOMESTIC : NOT USED
OP PANEL 35312-02 LASER
1 CON6
2 & HT CONT. TANK
35312-02 T
2
CON5 CON4 35312-05
35312-11 CON3 THERMAL
35312-05 EP_FB(-)
10
11
EP(-)
1
2
3
4
5
1
2
3
4
5
6
7
8
9
1
2
3
4
5
1
AGND
GND
LAMP_CONT
FIL_CONT1
FIL_CONT2
EP_CONT1
EP_CONT2
/100V_SEL
IP_FB(+)
IP(+)
FIL_FB
AGND
DGND
+12V
-12V
+5V
10
11
1
2
3
4
5
1
2
3
4
5
6
7
8
9
35312-05 35312-11
1
2
1
2
1
2
1
2
35312
1
CON7 2
35312
PXP60HF-PWR CON10
1
2
FG
35312
1
CON8 2
35312
1
PWR & DRIVE CON9 2
CON4 T2
1 C1 3
FILAMENT DRIVE 2 2
3 +12.2
CB1 4 SHIELD GND SHIELD LINE 3
53258-04 C2
FIL XFMR
5
4 53258-05
3
2 CON1
1 COLLIMATOR DRIVECON6
250V/16A 1
250V/20A 2 COLLIMATOR
CN1 SHIELD LINE
PLUG AC MALE LAMP
53258-02 12V/50W
4
Service Manual DIG-610
-PREPARATION
Following tools and instruments are needed.
a. Tools: Philips screwdriver No.1 & 2, Straight slot screwdriver
b. Instruments: DVM, oscilloscope (Tektronics TDS 3032 and more than Equivalent)
4. CALIBRATION PROCESS
kV mAs
-Set the kV and the mAs at 40kV and 0.4mAs (60mA). Then observe the mA waveform of the
oscilloscope channel 1.
-If it is not about 9V, adjust mA by VR3 on the OP board. Then observe the kV waveform of the
oscilloscope channel 2.
-If it is not 2V, adjust kV by VR2 on the OP board. After adjustment, set the tube voltage kV to 80KV
by the kV up/down switch.
-Set the kV and the mAs at 80kV and 0.4mAs(40mA).Then observe the mAs, kV waveform of the
oscilloscope channel 1, 2.
5
Service Manual DIG-610
kV mAs
-Set the kV and the mAs at 40kV and 0.4mAs (60mA). Then observe the mA waveform of the
oscilloscope channel 1.
-If it is not 7V, adjust mA by the calibration data on the OP board.
-Turn off the line switch, and wait until the display switch the light off.
-DIP switch 1 on the PCB OP board is turned on.
-Turn on the line switch and the display indicates as follows.
-Then push the mAs up switch (see operation sheet).
The display indicates as follows.
kV mAs
Calibration code Calibration data
6
Service Manual DIG-610
kV mAs
Calibration code Calibration data
kV mAs
Preheat calibration code Preheat calibration data
7
Service Manual DIG-610
kV mAs
Preheat calibration code Preheat calibration data
-Adjust data by the mAs up/down switch (on the control panel).
-After it is adjusted, push the Store switch (on the control panel).
-DIP switch 1 on the PCB OP board is turned off then exposure X-ray.
-If overshoot or undershoot occur in the waveform, set the calibration data again.
-Table. 2 shows the calibration code and the calibration data against an each tube current.
The calibration data is possible to be changed in accordance with the tube condition.
8
Service Manual DIG-610
9
Service Manual DIG-610
7. SCHEMATICS
(2F-5)
SEG_A (2G-5)
SEG_B (2H-5)
SEG_C (2J-5)
SEG_D (2K-5)
SEG_E (2L-5)
SEG_F (2N-5)
SEG_G (2O-5)
SEG_DP
R21
15 1/4W
1 2
R22
15 1/4W
1 2
10
10
10
10
10
10
7
5
U8 R23
DP
DP
DP
DP
DP
DP
G
G
A
E
C
D
F
F
(1B-13) 1 16 15 1/4W
SEG01_OUT I1 Q1
(1B-13) 2 15 1 2
SEG02_OUT (1B-12) 3 I2 Q2 14
SEG03_OUT I3 Q3
(1B-12) 4 13
SEG04_OUT I4 Q4
(1B-12) 5 12 R24
SEG05_OUT I5 Q5
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
(1B-12) 6 11 15 1/4W
SEG06_OUT (1B-12) 7 I6 Q6 10 1 2
SEG07_OUT 8 I7 Q7 9
GND VCC
3
8
3
8
3
8
3
8
3
8
3
8
SEG1 uD_SR105K SEG2 uD_SR105K SEG3 uD_SR105K SEG4 uD_SR105K SEG5 uD_SR105K SEG6 uD_SR105K
TD62304 R25
15 1/4W
1 2
+5V R26
15 1/4W
1 2
LED2 READY LED3 X-RAY LED4 WAIT LED5 M1 LED6 M2 LED7 M3 LED8 M4 LED9 M5
R27 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1
15 1/4W GREEN YELLOW RED GREEN GREEN GREEN GREEN GREEN
1 2
APPROVED BY DESIGNED BY
HTP-24 PORTABLE X-RAY
10
Service Manual DIG-610
+5V
1
RA7
4.7K
2
3
4
5
CON6
ISO_PWR (1B-10),(7G-13)
1 /FAULT
(1B-10),(5N-13)
IP_FB_IN
2 R29
ISO_GND 270
3 1 2
2
35312-0310
D33
1N4148 PC1
1 8 (1B-10)
HS_READY
1
CON1
2 7
1
2 3 6 (1B-9)
3 HS_X-RAY
R30
4 270
35312-0410 1 2
2
4 5
D34
1N4148 TLP620-2
+5V
D35 D36
CON2
2 1 2 1
1
1N4148 1N4148
(1M-7)
2 /LASER
35312-0210
APPROVED BY DESIGNED BY
HTP-24 PORTABLE X-RAY
11
Service Manual DIG-610
(7B-13)
IP_FB
R31 10K 1%
(1J-5)
IP_FB_ADC
R32
+12V
10K 1%
2
D37 U9A
4
LM358 U10 C21 BOX332
2
1N4148 2 - R33 39K 14 5 1 2
40mA(0 ~ 8V) R34 4.7k 1 1 3 1 +IN 1SC 10
-IN CPI
1
3 + 11
VR1 +12V COM
2
10K 12 7 (1B-10),(4J-11)
IP_FB_IN
2
+VS FOUT
8
+ D38 4 13
R35 C62 -VS VOUT
1/2W 200 1N4148 -12V VFC32
1
C22 MN104
1
C24 BOX103
6.8uF/16V tantal 1 2
CON3
IP_FB(+)
1
2
EP_FB(+) C60 39P
3 2 1
4
R75 100K 1%
5
35312-0510
(1A-10) (6B-14),(7B-11)
/HT_CHECK
EP_FB
+12V +12V C28 MN104
2 1
2
D39
8
100KV(0 ~ -5V) 1N4148 5 R36 1K
+
R37 100K 1% 7 (1J-5)
EP_FB_ADC
1
6
-
2
2
C25 C26 C27 LM358 R84
2
R
4
D40 U9B
BOX223 BOX223 BOX223 C58 MN104
1N4148
1
R76 2 1
1K
2
1
1
-12V C63
-12V
1
MN104
2
VR2 2K
1 3 R38
10K 1%
1 2
C29 MN101
2 1
TP3 C30 MN101
2 1 TP4
+12V
C31 MN104
1 2 EP_REF
1
IP_REF
1
R39
8
8
(1F-7) 1 2 3 10K 1%
EP_CONT +
1 (6B-14) (1F-7) 1 2 5
EP_REF IP_CONT
1
+
2 7 (6C-5)
IP_REF
2
1
-
C32 U11A 6
1
1
-
R41 LM358
1
4
4
10K 1% 1 2 10M MN101 R44
2
2
2 10K 1%
-12V
2
2
APPROVED BY DESIGNED BY
HTP-24 PORTABLE X-RAY
12
Service Manual DIG-610
+12V
+12V
R45
5.6K U12
(5J-9),(7B-11) 1 2 1 12 R47 910 CON4
EP_FB +IN1 VCC
(5F-4) 1 2 1 2
EP_REF 1
R46 1 2 2 8 EP_CONT1
5.6K 2 1 1 2 -IN1 C1 9 2
1
C36 3 E1 R50 910
C34 R48 R49 F.B. 1 2
BOX102 BOX682 470K 680 EP_CONT2 3
4
2
2 1 5 11
C37 BOX102 CT C2 10
1 2 6 E2 FIL_CONT1
R51 RT FIL_CONT2 5
6.2K 1% 4 6
DT
7
15 GND 14 LAMP_CONT 7
16 -IN2 VR 13 8
+IN2 OC
(6B-7)
TL494 FIL_FB 9
10
1
1
C38 + R52 /100V_SEL 11
47K
U13A 1uF/25V TANTAL
2
14066 35312-1110
2
1 2
1
R53
13
2K
2
(1M-6)
/HV_ON
2
+5V
2
R57
-12V 10K 1%
1
U13B
U14 +12V 14066
4
8
OP07 R59 11 10
R60 2 - 5.6K U15
4.7K 6 1 2 1 12
1
(6K-11) 1 2 3 + 1 2 +IN1 VCC
2
FIL_FB 1 2 2 8
12
R80 R61 2 1 1 2 -IN1 C1 9 R58
2
E1
7
1
2
2 1 BOX473 470K 10K
1
2 1 5 11
C42 BOX102 CT C2 10
+12V 3 1 2 6 E2
1 2 2 U17 R64 RT
1
PN2222 DRV1 1PN2222 5K 1% 4
2
2
R79 5.6K R70 470K
1
1 2 2 1
TL494
(5L-4) R78 30K C61 BOX104
IP_REF
1 2
IP_FB
R77 5.6K
1
1
C43 R67
BOX473 47K
U13C
2
14066
2
4 3
1
R68
5
2K
2
APPROVED BY DESIGNED BY
(1M-6)
/PREP HTP-24 PORTABLE X-RAY
13
Service Manual DIG-610
+12V +12V
TP5
+12V
2
C44
R69 R85 1 2
100k IP_FB
64K MN104
1
U16A
8
1
3
+
1
(5I-15) 1 2 2
IP_FB -
R71 LM393
4
100K
R86 C45
100k BOX473
(1B-10),(4J-11)
2
TP6 /FAULT
1 EP_FB
U16B +5V
8
5
+
7
1 2 6
EP_FB -
(5J-9),(6B-14)
R72 LM393 74HC573 27512 TD62304AP TD62304AP 14066
1
4
100K
2
2
10u/16V 56K 10u/16V 100K
1
TP7
+5V
+5V
1
C52 + C53
MN104 100uF/50V DGND HOLE HOLE HOLE HOLE HOLE HOLE HOLE HOLE HOLE HOLE HOLE HOLE
2
1
2
CON5 TP9
1
2 +12V +12V
3
1
4
5 TP11
TP10
1
35312-0510
1
C54 +
100uF/50V C55
MN104 AGND AGND
2
TP12
1
C56 + C57
100uF/50V MN104
-12V
2
2
14
Service Manual DIG-610
1
TP2 1N4937 IN OUT +5V 5
GND 1 6
GND
3 C24 +12.2V 2 7
Q21 C2235 R29 C45 GND 3 8
+ + CON8
27K C22 HS3 C46 100/16V -12V 4 G
DRV2A
1
2
100/16V CON2 +24V S 2
S1
C48 HS1 35312-5 +24V 35312
1
2
8 3 D15 S2L60 3 6 6 8
+ CON9
1
4 5 7
4
D10 +12.2V
5 C35 Q14 M472/100V C37
+ + + PN2222 R27 10 Q15 +15V
+ C36 C33 C34 R23 R41 1N4746 IRF640 D12
1N4937 2200/16V(13pie) 2200/16V 1W680 47K R28 1
47/25V 2200/16V R24 +15V Q17 R30 Z6 2
U4 6 1/2W470 PN2907 1N4937 1W1K 3
D11 1N4937 78L05 12 4
+ C40 20K
TG 3 1 R25 Q18 22/25V CON4
IN OUT R26 100 5.1K PN2222 R32 10 1N4746 Q19 53258-4
GND
IRF640
1
1N4937
4
TH
1
ISO_5V
DIG-610 PWR &DRV
2
ISO_GND R39
1%1.8K
C44 222/AC250V
3
2
1
2
1
15
Service Manual DIG-610
8. Maintenance
- When main power of product is on, and display will show values (kV and mAs) as following .
And this product is normal, please use safely.
kV
mAs
- If you have a problem, show error code on display and see page 28 and check it.
After the error code on display check it, if this error code is not appear
Please just let me know.
Tel +82-31-907-7222
Fax +82-31-904-2231
Homepage: www.dong-mun.co.kr
E-mail: dongmun@kita.net
16
Service Manual DIG-610
8. Technical
Technical date
TECHNICAL GUIDE
T-SPINE(AP) 100 + 75 25 2 14 14
17