Академический Документы
Профессиональный Документы
Культура Документы
com/
GMAW/
BASE METAL SMAW GTAW SAW
FCAW
QW-403 Base metal
11 E P-NO QUALIFED E E E E
8 E T QUALIFIED RANGE E E E E
9 > t PASS > 13MM (1/2 IN) E E E
IX
3 E M-GROUP QUALIFED S S S S
4 E M5A TO M5B, M9B TO M9A, M10/11 A/B E E E E
5 E BARE STEEL TO HDG/PAINT STEEL E E E E
Tab 4.5 General/ Tab 4.6 Base metal
29 E BASE METAL PQR OR GROUP IN TAB 4.8 E E E E
D1.1
QW-407 PWHT
1 E PWHT (NONE, <A1, > A3,A1< T<A3) E E E E
2 E PHWT (TIME & TEMP RANGE) S S S S
4 > T>A3 E E E E
2.14.5 Preheat & Interpass Temp'
1 < DECREASE OVER 55*C E E E E
2 > INCREASE OVER 55*C S S S S
B2.1
LEGEND
E :CHANGES > :GREATER THAN :ADDITION/DELETION
< :LESS THAN
E = Essential Variables which must be indicated on both the WPS and recorded on the PQR. Any changes to these variables will require
requalification of WPS
S = Supplementary Essential Variables must be indicated on the WPS and Recorded on the PQR when Impact Testing is required. Changes
to these variables when Impact testing is performed require requalification of WPS. ( QW-403.6-Where notch toughnes required min. base
Metal Thk. qualified is 16mm )
N = Nonessential variables must be indicated on the WPS but when changed do not require requalification of WPS.
NOTE: WPSs are to indicate all Essential, Nonessential and Supplementary Essential variables. Do not indicate variables which are not
used as NA they are applicable and should be entered on the WPS as None or Not used.
ASME IX, AWS B2.1, AWS D1.1 WPS & PQR CHECK LIST https://amarineblog.wordpress.com/
3 N N
5 BACKING PURGE (COMPOSITION, FLOW) N N
9 E BACKING PURGE (P4X, P10I, J, K, P5X, P6X) E E
10 E SHIELDING (P4X, P10I, J, K, P5X, P6X) E E
2.14.7 Shielding Gas
1 TORCH SHIELDING GAS E E
2 E NOMINAL COMPOSITION E E
B2.1
3 PULSING I TO DC N
4 E AC TO DC, DCEN TO DCEP & VISE VERSA S N S N S N S N
8 E I&U RANGE (EXCLUDE SMAW/GTAW) N N N N
12 E TUNGSTEN ELECTRODE N
2.14.8 Electrical Characteristics
B2.1
15 E CV-FLAT TO CC-DROP E
16 E VOLTAGE (> 7 %) E E
17 E WIRE FEED SPEED (> 10%) E E
18 E TRAVEL SPEED (GTAW >50%, OTHERS 15-25%) E E E
9 > HEAT INPUT (U&I or bead size increasing) S S S S
LEGEND
E :CHANGES > :GREATER THAN :ADDITION/DELETION
< :LESS THAN
E = Essential Variables which must be indicated on both the WPS and recorded on the PQR. Any changes to these variables will require
requalification of WPS
S = Supplementary Essential Variables must be indicated on the WPS and Recorded on the PQR when Impact Testing is required. Changes
to these variables when Impact testing is performed require requalification of WPS. ( QW-403.6-Where notch toughnes required min. base
Metal Thk. qualified is 16mm )
N = Nonessential variables must be indicated on the WPS but when changed do not require requalification of WPS.
NOTE: WPSs are to indicate all Essential, Nonessential and Supplementary Essential variables. Do not indicate variables which are not
used as NA they are applicable and should be entered on the WPS as None or Not used.
ASME IX, AWS B2.1, AWS D1.1 WPS & PQR CHECK LIST https://amarineblog.wordpress.com/
E = Essential Variables which must be indicated on both the WPS and recorded on the PQR. Any changes to these variables will require
requalification of WPS
S = Supplementary Essential Variables must be indicated on the WPS and Recorded on the PQR when Impact Testing is required. Changes
to these variables when Impact testing is performed require requalification of WPS. ( QW-403.6-Where notch toughnes required min. base
Metal Thk. qualified is 16mm )
N = Nonessential variables must be indicated on the WPS but when changed do not require requalification of WPS.
NOTE: WPSs are to indicate all Essential, Nonessential and Supplementary Essential variables. Do not indicate variables which are not
used as NA they are applicable and should be entered on the WPS as None or Not used.