Академический Документы
Профессиональный Документы
Культура Документы
MTNC010307C1
B2
Main Manual
(P6)
Panasonic
Models Chassis
PT-51G36E AP822
PT-51G36CE AP822
This Service manual is issued as a service guide for the models of the P6 family listed above. Included in this manual
are a set of schematics, alignment procedures, disassembly procedures and a complete parts list.
WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.
The service technician is required to read and follow the Safety Precautions and Important Safety Notice in this Main Manual.
Service Manual - 16 -
5. Repeat for blue focus VR while projecting blue 4. Position the longer tab of the four-pole magnet to
only. 90 degrees (uncorrected position). (See
6. Repeat for green. Figure 27).
Focus - Optical Lens Adjustment
Optical Adjustments
6-pole magnet
Note: This adjustment normally should not require (Dummy ring)
4-pole magnet
resetting unless the lens has been replaced or
Alignment magnet
adjustment has changed.
Adjustment knurled
locking knobs
Set 90 degrees
B G R
Figure 27. 4-pole magnet
5. Position the long tab of all alignment magnets and
REAR VIEW of the dummy ring together in an uncorrected
Figure 25. Optical Lens focus Adjustment position. (See Figure 28).
2. Turn the PTV ON. Apply and view a monoscope
pattern.
3. Adjust each lens focus for best focus while viewing
each CRT.
4. Cover the red and blue CRT, projecting green only.
Rotate the green lens for best focus around screen
center area.
5. Do the same for the red focus lens while projecting
red only.
6. Repeat for blue. Figure 28. Alignment magnet
Electric & VM Focus Adjustment, (or dummy ring)
Complete adjustment Procedure:
(Perform this adjustment when a CRT is replaced 1. Apply an NTSC cross hatch pattern with dots.
or when major adjustment is required) 2. Assure that digital convergence is disabled (Dac
Preparation: D0F from 0 to 1).
1. NTSC monoscope pattern. 3. Project red only. (Cover green and blue CRTs.)
2. NTSC cross hatch pattern with dots (pincushion). 4. Turn the red electrical focus adjustment VR (on
3. Set DAC D0f from 0 to 1 (disabling digital focus pack) fully counterclockwise and note the
convergence.) position of the dots at the center of the picture.
5. Turn the red electrical focus adjustment VR
fully clockwise.
6. If the position of the dots at the center of the screen
moves from the position noted in step 4., adjust the
four pole magnets until the dots are in the same
position as noted in step4.
7. Turn the red electrical focus adjustment VR (on
focus pack) fully counterclockwise and confirm that
the position of the dots at the center of the screen
did not move from their position noted in ste p6.
8. If the position of the dots at the center of screen
moved, repeat from step 4.
- 17 - Service Manual
9. If the position of the dots moved after repeated 6. Remove lens covers and enable digital
adjustments, adjust until the movement of the dots convergence by changing Dac D0F from 1 to 0.
is minimized.
10. Turn the red focus VR fully clockwise.
11. Adjust the 4-pole magnets until the shape of the
dots at the center of the screen is circular.
12. Adjust red focus VR until optimum focus is 3.0
achieved.
1.0
13. Apply NTSC monoscope pattern.
14. If the center of the monoscope pattern is not inside
the 15.0mm circle, shown in Figure 29, adjust the
centering magnets. Repeat the alignment magnet
adjustments and four pole magnet adjustments
(step 1. ~ step 12.). Figure 30. Vertical Size Adjustment
Horizontal Phase Adjustment
1. Apply a monoscope pattern.
2. Set DAC D0F from 0 to 1 (disabling digital
convergence).
3. Cover both red and blue lens so that only the green
lens is projecting the monoscope pattern.
4. Change H-Size DAC data (D03) to 63 (H_Size is
minimum).
5. Turn Green Screen control clockwise (Figure 24)
until all deflecting area appear.
Figure 29. Centering magnet 6. Adjust H-Position DAC data (D04) until left size is
60.1.
15. Apply an NTSC cross hatch pattern with dots.
Picture Screen
16. Cover red and blue lenses projecting green only. Area Frame
17. Repeat above procedures for the green.
18. Enable digital convergence by changing DAC D0f
from 1 to 0.
19. Following adjustments, paint position of DY
centering magnets and fix the centering magnets Deflecting
Area
of DY, dummy rings of VM coil, four pole magnets
of VM coil and the alignment magnets of VM coil to Figure 31. H Phase Adjustment
prevent them from moving.
7. Turn Green Screen control counter clockwise
Note: Please See Service Mode (Electronic (Figure 24) until the area between deflecting area
Controls) on page 25 for entering and exiting and picture area disappear.
Service Mode. 8. Enable digital convergence by changing DAC D0F
from 1 to 0.
Vertical Size Adjustment (D00) 9. Remove lens covers.
1. Apply an NTSC monoscope pattern. Trapezoid Adjustment (D06)
2. Cover red and blue lenses. Procedures:
3. Set DAC D0F from 0 to 1 (disabling digital 1. Cover Red and Blue Lenses.
convergence). 1. Apply a crosshatch pattern.
4. Adjust centering magnets so that the center of 2. Set DAC D0F from 0 to 1 (disabling digital
pattern get aligned with screen frame center. convergence).
5. Adjust DAC D00 (V_Size) until vertical size is 3. Adjust DAC D06 (trapezoid) by pressing VOL right-
4.00.1 on top and bottom lines. (See Figure 30) left to correct image (See Figure 32).
- 19 - Service Manual
Raster Setup: 16. In FINE ADJUSTMENT MODE options, press
1. Cover Red & Blue lens with caps. MUTE key on remote to switch between cursor
2. Apply an NTSC monoscope pattern. mode and data mode.
3. Select DAC V00, then press VOL right or left to Cursor mode: Allows cursor movement by
enter to CONVERGENCE ADJ mode. pressing VOL right - left and CH up - down.
4. Press 0 key on remote. Data mode: Allows making adjustment by
5. Press ACTION key on remote to enter to pressing VOL right - left and CH up - down.
TEST_POS mode. 17. Either COARSE ADJUSTMENT MODE options
6. Move pattern by pressing VOL right - left and CH or FINE ADJUSTMENT MODE options, press R-
up - down so that the cursor center overlap TUNE repeatedly key on remote to cycle through
monoscope pattern center. different color adjustments (R,G,B,White)
18. To store adjustments press 7, then ACTION key
on remote, otherwise press POWER then
ACTION to exit adjustments without saving.
19. Remote Functions:
Service Manual - 20 -
6. Enter to linearity G-LINEAR mode by pressing 18. Press 7 then ACTION key on remote to save
TV/VIDEO. changes
7. Adjust linearity by pressing VOL right-left until A=B
(See Figure 39)
A B
A B
Red
Green
- 21 - Service Manual
25. Enter to LINEARITY R-LINEAR mode by Fine Adjustment Mode (V01)
pressing TV/VIDEO. (Convergence)
26. Adjust Horizontal linearity (See Figure 39)
27. Enter to SIZE R-SIZE mode by pressing TV/ Note: It is strongly recommended to first read and
VIDEO understand the following section prior to
28. Adjust so that the line on the border closes to the make any adjustment.
screen frame at top, bottom, left and right (See
Figure 38)
29. Enter to PIN R-PIN mode by pressing TV/VIDEO Helpful Hint:
30. Adjust horizontally and vertically (See Figure 40) The easiest way to adjust convergence is to begin
31. Enter to CORNER R-CORNER mode by pressing from the center of the screen, to the border in all the
TV/VIDEO. convergence adjustments.
32. Adjust corners (See Figure 41)
33. Enter to KEY R-KEY mode by pressing TV/ Remote Functions:
VIDEO 1, 3. . . . . . . . . . .change color view adj
34. Adjust KEY (See Figure 42) 2. . . . . . . . . . . . . . . . . . change pattern
35. Display pattern of border and cross, then check 7. . . . . . . . . . . . . . . . . . . . . . . save data
that red overlaps green pattern, if it is not 5. . . . . . . . . . . . . . . . . . . . . . . . . overlap
satisfactory, repeat from step 19. POWER . . . . . . . . . . . . . . . . . . . . to exit
36. Enter to STATIC B-STATIC mode. RECALL . . . . . . . . . . . . display values
37. Press 1 or 3 key repeatedly on remote until only R-TUNE . . . . . . . . . . . . . . . cycle colors
green and blue pattern are displayed TV/VIDEO . . . . . . . . . . . . change mode
38. Adjust B-STATIC so that the center of blue 3 secs. . . . . . . change options
overlaps with the center of green (See Figure 45). MUTE (fine) . . . cursor & data mode
In FINE ADJUSTMENT MODE options, press
MUTE key on remote to switch between cursor
mode and data mode.
Cursor mode (cursor flashing): Allows
cursor movement by pressing VOL right - left
and CH up - down.
Data mode (cursor fixed): Allows making
Blue adjustment by pressing VOL right - left and
Green
CH up - down.
Procedure:
Figure 45. B-STATIC adjustment
39. Perform all adjustments for Blue (B-SKEW, B- 1. Enter to G-EASY mode (for green):
LINEAR, B-SIZE, B-PIN, B-CORNER, B-KEY) DAC V01
40. Display Border and cross pattern and confirm that VOL right or left
blue overlaps with green pattern, if it is not TV/VIDEO (repeatedly)
satisfactory, repeat for blue. R-TUNE (repeatedly)
41. Press 1 or 3 key repeatedly on remote until 2. Press 2 repeatedly and apply the pattern of
Green, Red and Blue (White), confirm that red and crosshatch.
blue overlaps with green pattern. 3. Press 1 or 3 repeatedly until the pattern becomes
42. Press 7 key on remote, then ACTION to save green.
changes. 4. Press RECALL to display values.
43. Press POWER then ACTION to exit adjustments or 5. In EASY mode, the adjustment value changes by
press TV/VIDEO for at least 3 seconds to change 4 steps
to Fine Adjustment Mode. 6. EASY mode allows to move lines horizontally and
vertically from the center of cursor.
Cursor
Service Manual - 22 -
7. This mode afects a wide area around the cursor 17. Begin adjustment from the center to the edge of
than other adjustment modes, See values on the screen.
screen by pressing RECALL on remote
(seeFigure 47) left/right
8. Begin adjustment from the center to the edge of
the screen.
9. Adjust by pressing CH up/down and VOL right/lef
on the remote control when the cursor is not
blinking, if the cursor is blinking press MUTE on the
remote. up/down
left/right
Figure 48. POINT & ORIG. POINT cursor positions Note: Since convergence adjustment will not
allows to adjust every single cross section
16. When the cursor is located in the outer area of the of the grid, it is very important to adjust, so
border the cursor starts to blink from one side to that overall looks best.
other and the adjustment is for the non-visible area
(inside the ovals area, see Figure 48); This applies
to POINT & ORIGIN. POINT modes.
- 23 - Service Manual
. 30. Perform adjustments so that blue overlaps Yellow
(Red and Green).
left/right 31. Press 1 or 3 key on remote to display red, green
and blue (White).
32. At this point the crosshatch pattern should look
white
33. If the crosshatch pattern is not only white, repeat
adjustment for that color (Red or Blue)
up/down 34. Once the crosshatch pattern looks only white,
perform the adjustments for White (POINT,
ORIG. POINT & LINE), notice that each
adjustment is only for white (Red,Green,Blue)
35. Adjust white for a good line distribution and make
Figure 51. LINE adjustment lines completely straight.
36. Press 7 key on remote, then ACTION to save
28. Perform adjustments for red so that red overlaps changes.
green, do not move green. 37. Press POWER then ACTION to exit adjustments.
29. Press 1 or 3 on the remote until Yellow (Red and
Green) and blue appears, do not move green or
red.
Horizontal and Vertical Size Check
1. Apply monoscope pattern.
3.5
4.0 2.0
Service Manual - 24 -
Service Mode (Electronic Controls)
This PTV has electronic technology using the IC Bus 8. CHK = Normal operation of CHANNEL
Concept. It performs as a control function and it and VOLUME .
replaces many mechanical controls. Instead of
adjusting mechanical controls individually, many of the b a b a
control functions are now performed by using On
32 B 0 2 215 C 0
Screen Display Menu. (The Service Adjustment
Mode.)
An address Menu appears in the right
hand corner of the screen
Note: It is suggested that the technician reads all the
way through and understand the following
procedure for Entering/Exiting the Service Figure 54. Service Mode Menu Adjustments.
Adjustment Mode; then proceed with the
instructions working with the PTV. When
becoming familiar with the procedure, the Flow Exiting the Service Mode:
Chart for Service Mode may be used as a Press the Action and Power on the PTV
quick guide. simultaneously for at least 2 seconds.
THE PTV EXITS SERVICE MODE.
The PTV momentarily shuts off; then comes back on
Quick Entry to Service Mode: tuned to channel 3 with a preset level of sound.
When minor adjustments need to be done to the
Any programmed channels, channels caption data and
electronic controls, the method of Entering the service
some others user defined settings will be erased.
Mode without removal of the cabinet back is as follows
using the Remote Control:
IMPORTANT NOTE:
1. Select SET-UP icon and select CABLE mode.
2. Select TIMER icon and set SLEEP time for 30 Min.
Always Exit the Service Mode
3. Press ACTION twice to exit menus. Following Adjustments.
4. Tune to the Channel 124.
5. Adjust VOLUME to minimum (0).
6. Press VOL (decrease) on PTV. Red CHK To Check Purity:
appears in upper corner. Press Recall on the Remote Control when in Service
Mode (red CHK is displayed) to enter the Purity Field
Check Mode.
Note: After PTV is set into SERVICE mode, set
TIMER back to NO. NORMAL
SCREEN
- 25 - Service Manual
Service Mode (Electronic Controls, Continued)
Note: Registers marked as FIXED are factory preset, Adj. Default
Service Adjustment
the default value must not be changed Range Level
C03 Brightness FIXED 31
Important Note: C04 G Drive (RF) 0 ~ 127 65
Write down the original values (b in the
adjustment mode details, Figure 54) for each C05 B Drive (RF) 0 ~ 127 66
address adjustment before modifying values. C06 G CutOff (Video) FIXED 127
Follow the procedure below to access the various C07 B CutOff (Video) FIXED 127
Service adjustments. (Same procedures applies to
each section.) C08 G Drive (Video) FIXED 127
a. Press C09 B Drive (Video) FIXED 127
CH buttons on the Remote Control to select any of
C0A G CutOff (Component) FIXED 127
the seven Service Sub Adjustment Addresses. (a in
Figure 54) C0B B CutOff (Component) FIXED 127
b. Press C0C G Drive (Component) FIXED 127
The buttons on the Remote Control to adjust the
level of the selected Service Adjustments. C0D B Drive (Component) FIXED 127
Service Manual - 26 -
P PIP Adjustments Adj. Default
Service Adjustment
Range Level
Adj. Default
Service Adjustment
Range Level S12 Surround Effect FIXED 3
P00 PIP Color FIXED 92 Table 9: Serviceman Adj. S00 ~ S12 (Continued)
P01 PIP Tint FIXED 54
X Option Items
P02 PIP Brightness 0 ~ 31 22
P03 PIP Contrast 0 ~ 127 80 Adj. Default
Service Adjustment
Range Level
P04 PIP V Position 9 Up FIXED 27
X00 Clip Level FIXED 8
P05 PIP V Position 9 Down FIXED 144
X01 Correct Gain ---- ----
P06 PIP H Position 9 Left FIXED 12
X02 Limit Level FIXED 24
P07 PIP H Position 9 Right FIXED 103
X03 Core Level FIXED 41
P08 PIP V Position 16 Up FIXED 27
X04 C Delay (RF) FIXED 2
P09 PIP V Posit 16 Down FIXED 161
X05 C Delay (Video) FIXED 5
P0A PIP H Position 16 Left FIXED 12
X06 VM Limit Level FIXED 90
P0B PIP H Position 16 Right FIXED 118
X07 VM Core Level FIXED 8
P0C PIP Freerun ---- ----
X08 Sharpness FIXED 50
P0D PIP Y Delay FIXED 4
X09 VM Limit Level A FIXED 255
P0E PIP BG Start FIXED 17
X0A VM Freq. SW FIXED 1
Table 8: Service Adj. P00 ~ P0E
Table 10: Service Adj. X00 ~ X0A
S Option Items
V Option Adjustments
Adj. Default
Service Adjustment
Range Level Adj. Default
Service Adjustment
Range Level
S00 B.S. Point FIXED 7
V00 Static Conv. Mode ---- ----
S01 RGB Gamma FIXED 1
V01 Point Conv. Mode ---- ----
S02 Col Gamma FIXED 0
V02 DAF Mode ---- ----
S03 ABL Gain FIXED 2
V03 DAF ON/OFF FIXED 0
S04 ABL Point FIXED 0
V04 ABL Input Level FIXED 5
S05 RGB Brightness FIXED 10
V05 Blue Gamma FIXED 0
S06 MTS Input Level 0 ~ 63 33
V06 VM ON/OFF FIXED 0
S07 MTS Low Separation 0 ~ 63 8
V07 ABL ON/OFF FIXED 0
S08 MTS High Separation 0 ~ 63 30
Test Pattern
S09 Clock adjustment 0 ~ 255 128 V08 0 ~ 255 20
Vertical Phase
S0A Loudness Comp FIXED 7
Test Pattern
V09 0 ~ 255 29
S0B Caption Digital Filter SW FIXED 1 Vertical OSD
S0C Caption Scroll FIXED 1 Test Pattern
V0A 0 ~ 255 65
Horizontal OSD
S0D RGB MTX (RF/Video) FIXED 6
V0B V1 Delay 0 ~ 255 1
S0E RGB MTX (Component) FIXED 5
User Static Data
S0F BBE ON/OFF FIXED 1 V0C FIXED 100
(Vertical, Red)
S10 BBE Low Level FIXED 4 User Static Data
V0D FIXED 100
S11 BBE High Level FIXED 6 (Vertical, Green)
- 27 - Service Manual
Adj. Default Contrast Adjustment
Service Adjustment Preparation:
Range Level
1. Set Auto Color and AI Picture to OFF
User Static Data 2. Set the following in the user picture menu as
V0E FIXED 100
(Vertical, Blue) follows:
User Static Data COLOR: min. (0)
V0F FIXED 100 PICTURE: max (63)
(Horizon, Red)
BRIGHT: center (31)
User Static Data SHARPNESS: min. (0)
V10 FIXED 100
(Horizon, Green)
Set CutOff Data:
User Static Data DAC C00 (R_CutOff) to 128.
V11 FIXED 100
(Horizon, Blue) DAC C01 (G_RF CutOff) to 128.
DAC C02 (B_CutOff) to 128.
Test Pattern Horizontal
V12 FIXED 0 ~ 90 DAC C06 (G_Video CutOff) to 127.
Phase (LOW)
DAC C07 (B_Video CutOff) to 127.
Test Pattern Fine DAC C0A (G_Video Component) to 127.
V13 FIXED 4 ~ 100
Horizontal Phase (LOW) DAC C0B (B_Video Component) to 127.
Test Pattern Coarse Set Drive Data:
V14 FIXED 0~0 DAC C04 (G_Drive RF) to 64.
Horizontal Phase (LOW)
DAC C05 (B_Drive RF) to 64.
V15 Start Line (LOW) FIXED 0 ~ 11
Procedure:
Table 11: Service Adj. V00 ~ V15 (Continued)
1. Use 100:1 probe for measurements.
2. Apply a Black/White Pattern (See Figure 56)
HV_Feedback Voltage (D08)
Procedure:
1. Apply a NTSC all black pattern.
2. Connect meter (+) to TPA38 and (-) to TPA20
3. Adjust DAC D08 so that reading on meter is
5.0_V0.2_V.
Sub-Bright Adjustment (B00)
Procedure:
1. Set to normal picture settings.
2. Connect meter (+) to TPA18 and (-) to TNPA19.
3. Apply a black level pattern. Figure 56. Black/white Pattern
4. Adjust DAC B00 (Sub-Brightness) so that reading 3. Connect Scope to TPLR1 and adjust Sub-Bright
on meter is 17.0_V1_V (7.5 IRE part is same light (B00) data until voltage measured is 190V 2V.
output as 3 IRE part (See Figure 56). See Figure 57.
5. Apply a monoscope pattern and put bright control 4. Connect Scope to TPLG1 and adjust R-CutOff
to max. and confirm same reading on meter. (C00) data until voltage measured is 190V 2V.
(See Figure 57).
5. Connect Scope to TPLB1 and adjust B-CutOff
(C02) data until voltage measured is 190V 2V.
(See Figure 57).
6. Connect Scope to TPLR1 and adjust Sub-Contrast
(B01) data to obtain 85V2 V between black
(7.5 IRE) and White level (See Figure 57).
7.5 IRE
85V2V (R)
190V2V (R, G,B)
Service Manual - 28 -
Service Mode (Electronic Controls, Continued)
Red, Green & Blue Screen Cutoff MTS Circuit Adjustments
1. Use either a no input signal condition or raster from Note: It is important to adjust the MTS circuit in the
the NTSC generator. order shown below.
2. Observing the green tube directly or via a reflective The MTS Circuit Adjustments require two steps:
surface, adjust the VR on the green tube for 1. Input Level Adjustment.
minimum noise. 2. Stereo Separation Adjustment.
3. Adjust the noise level in the red and blue tubes to Input Level Adjustment (S06)
match the noise level in the green tube. Preparation:
White Balance Adjustment 1. Connect an RMS meter (AC Range) with filter jig
Prior to this adjustment, perform Contrast adjustment. as shown in Figure 58.
This adjustment requires that the service use skills in
observing what a screen without color should look like RMS TPE11
METER L_OUT
(White Picture). 10k
1. Enter the service mode.
2. Apply a black and white pattern to one of the video
4700p
inputs. Figure 58. Filter Jig
High Light White Balance Adjustment
2. Connect an RF signal generator to the RF
1. Adjust DAC C04 for Green and C05 for Blue
antenna input.
adjustments.
Procedure:
2. Make sure the screen is not blue or Green. The
1. Apply the following signal from the RF signal
screen should be white in all areas.
generator:
3. Check the black and white pattern for a black and
Video: 100 IRE flat field, 30% modulation.
white picture with even shades of gray and no color
Audio: 300Hz, 100% modulation, monaural
tint in the picture.
(70 5dB, 75 OPEN, P/S 10dB). Make sure to
Low Light White Balance Adjustment
turn off 75s pre-emphasis.
1. Adjust DAC C01 for Green and DAC C02 for blue.
2. Adjust (S6) MTS-INPUT data until the voltage
2. Check the screen for even white in all areas, no
measured is 106mV 6.0mV rms.
color.
3. Check the black and white pattern for a black and
Stereo Separation Adjustment (S07 & S08)
white picture, even shades of gray and no color tint
Preparation:
in the low light areas.
4. Repeat the High Light and Low Light White 1. Connect an RF signal generator to the RF
Balance again until the white balance tracks from antenna input.
high light to low light. 2. Connect an oscilloscope probe to TPE10 (R_out).
Procedure:
Tint and Color Check 1. Set PTV to Stereo Mode (in the Audio Menu).
Again, the service ability to see color and the balance 2. Apply the following signal from the RF signal
of color is important for theses adjustments.
generator:
Tint Check Video: 100 IRE flat field, 30% modulation.
1. In Picture Menu set Picture Norm to YES. Audio: 300Hz, 30% modulation, stereo (left only)
2. Apply color bars to the video input. (70dB 5dB, 75 OPEN, P/S 10dB).
3. Magenta is composed of two colors, blue and red.
4. Check to see that magenta does not have too
much blue or too much red. Note: Set the 30% modulation with the pilot
5. Check cyan. Cyan is composed of blue and green. light SW and N.R. switches OFF then turn
It should not have too much blue or green. them ON while testing.
6. Use a test signal from a VCR or laser disk that has
a pre-recorded close up of a signal that has good 3. Adjust MTS Low-Level Separation (S07) data (in
flesh tones. the Service Adjustment Menu) until the amplitude of
7. The signal on the VCR or laser disk should look the measured waveform on the scope is minimum.
normal. 4. Apply the following signal from the RF
Color Check signal generator:
Using a clean RF or video signal, set the color level so Video: 100 IRE flat field, 30% modulation.Audio:
that it does not saturate or appear harsh. Make sure 3KHz, 30% modulation, stereo (left only).
that color is not set so that it appears dull and washed (70dB 5dB, 75 OPEN, P/S 10dB).
out. Look for natural colors, try to adjust the picture to
appear as a normal photograph.
- 29 - Service Manual
Service Mode (Electronic Controls, Continued)
PIP Adjustment
Note: Set the 30% modulation with theP.L and
N.R. switches OFF then turn them ON while Preparation:
testing. 1. Apply a color bar pattern.
2. Connect Scope to Connector A20 pin 2 on A-Board
or Connector Y1 pin 2 (TPY2) on Y-Board.
5. Adjust MTS High-Level Separation (S08) data until 3. Turn PIP on.
the amplitude of the waveform measured on the
scope is minimum. Procedure:
6. Repeat above steps 2 through 4 until the amplitude 1. Adjust DAC P03 (PIP Contrast) so that Child
is at minimum for both signals. Waveform level is 90% of Parent Waveform level
(See Figure 59).
Clock Adjustment (S12) WHITE P-Y
Preparation: Child
Perent C-Y
Connect the frequency counter from IC001 MPU
Pin 34 or TPA39, to cold ground ( ). 0.90.1Vp-p
1.00.1Vp-p
Note: Frequency Counter probe capacitance should
be 8pF or less.
BLACK
Procedure:
1. Turn the PTV ON with the AC power applied. Figure 59. Parent and Child Y
2. Measure IC001 MPU pin 34 for frequency and
record the reading.
{ 187.5000 pin ( 34 ) [ Hz ] }
S ( 09 ) = 128 + 1.35x10 6 x -----------------------------------------------------------------
187.5000
Service Manual - 30 -
PT-51G36E/EC A-Board Schematic, Left Portion
- 50-
A-Board Schematic & Waveforms PT-51G36E/EC
WAVEFORMS
1 A-Board
IC451 Pin 2 - 67.2Vp-p
V-OUT
1 A-Board
Q501 COLLECTOR - 188Vp-p
H-DRIVE
- 51-
PT-51G36E/EC P-Board Schematic, Left Portion
- 52-
P-Board Schematic & Voltages PT-51G36E/EC
Q801 Q802
S 0.00 0.71
D 16.10 0.10
G 4.87 0.00
- 53-
PT-51G36E/EC X-Board Schematic, Left Portion
- 54-
X- Board Schematic, Right Portion & Voltages PT-51G36E/EC
IC001 IC101
1 ..... 4.72 33 . . . . . . 4.78 1 . . . . . . 4.14 29 ..... 3.90
2 ..... 4.94 34 . . . . . . 0.00 2 . . . . . . 0.00 30 ..... 4.15
3 ..... 2.45 35 . . . . . . 4.88 3 . . . . . . 3.37 31 ..... 0.00
4 ..... 0.00 36 . . . . . . 0.00 4 . . . . . . 3.36 32 ..... 0.00
5 ..... 4.89 37 . . . . . . 4.92 5 . . . . . . 3.36 33 ..... 4.60
6 ..... 2.00 38 . . . . . . 0.00 6 . . . . . . 0.00 34 ..... 0.97
7 ..... 2.12 39 . . . . . . 4.26 7 . . . . . . 8.56 35 ..... 1.91
8 ..... 4.89 40 . . . . . . 4.27 8 . . . . . . 0.00 36 ..... 4.33
9 ..... 0.74 41 . . . . . . 0.00 9 . . . . . . 5.16 37 ..... 8.70
10 ..... 1.51 42 . . . . . . 0.00 10 . . . . . . 0.00 38 ..... 3.10
11 ..... 1.45 43 . . . . . . 0.00 11 . . . . . . 7.55 39 ..... 5.92
12 ..... 0.00 44 . . . . . . 0.00 12 . . . . . . 4.54 40 ..... 7.24
13 ..... 4.78 45 . . . . . . 3.61 13 . . . . . . 2.51 41 ..... 5.64
14 ..... 4.89 46 . . . . . . 1.53 14 . . . . . . 2.49 42 ..... 4.77
15 ..... 4.89 47 . . . . . . 1.54 15 . . . . . . 2.56 43 ..... 1.10
16 ..... 0.00 48 . . . . . . 0.00 16 . . . . . . 8.71 44 ..... 0.00
17 ..... 4.76 49 . . . . . . 4.94 17 . . . . . . 4.93 45 ..... 1.71
18 ..... 4.91 50 . . . . . . 1.32 18 . . . . . . 4.79 46 ..... 1.56
19 ..... 3.88 51 . . . . . . 1.32 19 . . . . . . 4.71 47 ..... 2.15
20 ..... 0.00 52 . . . . . . 4.94 20 . . . . . . 2.07 48 ..... 2.17
21 ..... 1.86 53 . . . . . . 4.92 21 . . . . . . 2.31 49 ..... 3.77
22 ..... 4.94 54 . . . . . . 4.94 22 . . . . . . 1.15 50 ..... 3.25
23 ..... 0.28 55 . . . . . . 4.59 23 . . . . . . 7.28 51 ..... 4.79
24 ..... 3.23 56 . . . . . . 4.92 24 . . . . . . 0.64 52 ..... 2.84
25 ..... 1.16 57 . . . . . . 4.88 25 . . . . . . 5.06 53 ..... 2.87
26 ..... 2.89 58 . . . . . . 4.88 26 . . . . . . 2.00 54 ..... 3.69
27 ..... 1.27 59 . . . . . . 4.15 27 . . . . . . 4.31 55 ..... 3.01
28 ..... 4.06 60 . . . . . . 3.92 28 . . . . . . 3.11 56 ..... 3.13
29 ..... 3.96 61 . . . . . . 4.94
30 ..... 0.00 62 . . . . . . 2.32
31 ..... 4.73 63 . . . . . . 2.55
32 ..... 4.78 64 . . . . . . 0.00 IC6501
1 . . . . . . 0.00 15 ..... 2.65
2 . . . . . . 4.74 16 ..... 3.34
3 . . . . . . 0.00 17 ..... 3.34
IC005 IC002 4 . . . . . . 0.00 18 ..... 2.23
1 ..... 0.00 5 . . . . . . 0.00 19 ..... 0.00
1 . . . . . 7.70 6 . . . . . . 0.00 20 ..... 2.35
2 . . . . . 0.00 2 ..... 0.00
3 ..... 0.00 7 . . . . . . 0.71 21 ..... 1.40
3 . . . . . 4.94
4 ..... 0.00 8 . . . . . . 4.74 22 ..... 0.39
5 ..... 4.16 9 . . . . . . 3.94 23 ..... 4.78
6 ..... 3.92 10 . . . . . . 4.06 24 ..... 0.37
7 ..... 0.00 11 . . . . . . 0.00 25 ..... 1.14
8 ..... 4.94 12 . . . . . . 2.34 26 ..... 1.14
13 . . . . . . 0.00 27 ..... 3.47
14 . . . . . . 2.27 28 ..... 0.55
- 55-
PT-51G36E/EC K, G & R Board Schematics & Layouts
R-Board Layout
K-Board Layout
G-Board Layout
- 58-
LB-Board Schematic, Layout & Voltages PT-512G36E/CE
- 59-
PT-51G36E/CE LG-Board Schematic, Layout & Voltages
- 60-
LR-Board Schematic, Layout & Voltages PT-51G36E/CE
- 61-
PT-51G36E/CE Y-Board Schematic, Layout & Voltages