Академический Документы
Профессиональный Документы
Культура Документы
Contents Page:
1. Scope of Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Work Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Shift Linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4 Yarn Unreeler for Yarn and Wool Cones . . . . . . . . . . . . . . . . . . 7
2.5 Yarn Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Nominal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Drive Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Direction of Motor Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 V-belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3
1
4
2. Installation
ATTENTION !
The buttonhole machine may only be installed by trained
personnel.
2.1 Transport
For in-house transport the machine must be lifted and transported on a suitable wagon
(e.g. pallet truck).
The shift linkage from the hand shift lever to the pedal is to be set appropriate to the
work height.
Loosen screw 5.
Set the pedal.
The operator must be able to switch off the machine unhindered by stepping
forward on the pedal.
Tighten screw 5.
5
1
6
2.4 Yarn Unreeler for Yarn and Wool Cones
The mounting and position of the yarn stand can be seen in the illustration alongside.
Insert stand 2 and fasten as shown in the picture with the nuts and washers.
Fasten the yarn roll holder and take-off arms.
The yarn roll holder and take-off arms must stand vertically above one another.
7
1 2 3 4
L1 L2 L3 L1 L2 L3
U V W U V W
X Y Z X Y Z
8
3. Electrical Connection
ATTENTION !
All work on the electrical equipment of the buttonhole
machine may only be conducted by electricians or suitablly
instructed personnel.
The mains plug must be disconnected.
The nominal voltage listed on the motor rating plate and the mains voltage must be the
same !
For conversion to a different mains voltage the appropriate drive package must be
mounted.
For conversion to a different mains voltage the following changes are to be made:
If changed from 3-phase to 2-phase or vice versa, the whole drive package must
be changed.
If changed from 50 Hz to 60 Hz or vice versa, only the belt pulley and the V-belt
must be replaced.
If changed from 3 ~ 400 V to 3 ~ 230 V or vice versa, the bridges in the motor
terminal box 3 must be switched in " Star " or " Delta ", appropriate to the mains
voltage !
The wiring is shown in the hook-up diagram.
9
3.3 Checking the Direction of Motor Turn
ATTENTION !
Before commissioning the buttonhole machine it is
essential that the direction of motor turn be checked.
Turning on the machine with an incorrect direction of motor
turn can lead to damage of unit.
With single phase, alternating current motors the direction of turn is set automatically if
terminal connections are made according to the hook-up diagram.
10
3.4 V-belt Tension
11
1
2 3
12
4. Installation of a Sewing Light
The sewing light is available as optional equipment.
ATTENTION !
Pull the mains plug !
The electrical connection may only be made by electricians
or appropriately instructed personnel.
13
5. Filling the Oil Reservoir
1 2
ATTENTION !
Before commissioning the machine the oil reservoirs 1 and
2 must be filled to the " max. " marking.
The lubrication of the buttonhole machine occur out of 2 reservoirs via an oil wick
system.
Additionally, the marked areas on the material carrier plate and the guide curve housing
must be oiled (see Operating Instructions 558).
As lubricating oil ESSO SP-NK 10 or an equivalent oil is to be used.
The lubricating oil is available at DRKOPP-ADLER AG business offices.
For the first filling there is an oil pillow in the accessories pack. The filling to be
conducted with the enclosed oil can.
14