Академический Документы
Профессиональный Документы
Культура Документы
1
SF.SPG35.T.A2.0911.EN
Technical Catalogue
SF.SPG35.T.A2.0911.EN
INDEX
MODULAR CODE.................................................................................................................................8
STANDARD SUPPLY............................................................................................................................9
RANGE..........................................................................................................................................10
SPG35.035....................................................................................................................................11
SPG35.050...................................................................................................................................12
SPG35.065...................................................................................................................................13
SPG35.080...................................................................................................................................14
SPG35.095.....................................................................................................................................15
SPG35.110.....................................................................................................................................16
SPG35.125....................................................................................................................................17
SEISMIC ZONE.............................................................................................................................18
OPTIONS............................................................................................................................................19
VERSION......................................................................................................................................19
LEGS.............................................................................................................................................20
PROVISION FOR FILTER.............................................................................................................22
PROVISION FOR VCP..................................................................................................................24
PROVISION FOR IPX...................................................................................................................25
FILLING PIPE................................................................................................................................26
SLEEVES ON CAP........................................................................................................................27
BOTTOM CONE............................................................................................................................28
FLUIDIZATION..............................................................................................................................30
FLANGE AT OUTLET....................................................................................................................31
LADDER........................................................................................................................................32
RAILING........................................................................................................................................34
CONNECTING GANGWAY...........................................................................................................37
SURFACE TREATMENT AND SHADES......................................................................................38
ACCESSORIES..................................................................................................................................39
LEGS EXTENSION.......................................................................................................................39
FILLING PIPE AND EXHAUST PIPE EXTENSION .....................................................................40
LADDER AND CABLE GLAND TUBE EXTENSION.....................................................................41
SUPPORTING FRAME.................................................................................................................42
ADAPTERS FOR FILTER.............................................................................................................45
COMMERCIAL COMPONENTS PRESENT IN SILOS.................................................................46
RECOMMENDED ACCESSORIES TO BE MOUNTED ON SILO................................................47
2 1-Technical Catalogue
1-Technical Catalogue
The silo is a tank for the collection and storage of bulk solid materials in powder or granular form, with varying
particle size (cement, sand, limestone, lime, fly ash, etc.).
It is mainly used in the building sector.
Filling is done by means of a pneumatic pumping system, by means of a tube provided for the purpose in the
silo.
The pressure generated inside during pneumatic conveying passses through a filter placed on the silo roof or
on the ground.
The silos are located mainly outdoors and are fixed to a concrete platform.
The customer is responsible for sizing and construction of the afore-mentioned structure.
NOTE: If material other than cement, or material with special fluidity or granulometry features is to be
stored, contact the Manufacturer.
The silo can be equipped with various accessories, which, in certain circumstances become obligatory, such
as the dust filter.
In fact, in the light of the recent regulatory standards concerning environmental safety it is important to install
dust filters on silos containing dusty materials.
If the above-mentioned filters are installed at the top, ladders with rest landing must be provided to be able to
reach the top of the tank in complete safety to allow operators to carry out inspections and maintenance.
An inspection cover is provided at the top of the silos for inspection inside
SF.SPG35.T.A2.0911.EN 3
SF.SPG35.T.A2.0911.EN
Silos and accessories are designed and constructed according to the following standards:
1. ENV 1991-1:1996, Eurocode 1-1, Calculation basis and actions on structures
2. ENV 1991-2-1:1996, Eurocode 1-2, Actions on structures-Densities, self-weights and imposed loads
3. ENV 1991-2-3:1996, Eurocode 1-2-3, Actions on structures-Snow loads
4. ENV 1991-2-4:1997, Eurocode 1-2-4, Actions on structures-Wind actions
5. ENV 1991-4:1997, Eurocode 1-4, Calculation basis and actions on structures-actions on silos and
tanks
6. ENV 1993-1-1: 1994/A1:1998, Eurocode 3-1-1, Design of steel structures, general rules and rules for
buildings
7. ENV 1993-4-1:2002, Eurocode 4-1, Silos, tanks and pipelines-Silos
8. ENV 1998-1-1:1997, Eurocode 8-1-1 Design of structures for earthquake resistance -Seismic actions and
general requirements for the structures
9. ENV 1998-4:2000, Eurocode 8-4 Silos, tanks and pipelines
10. UNI EN 131/1 1994 ,Ladders: terminology, types and functional sizes
11. EN ISO 14122-3 : 2001 Stairs, step ladders and guard-rails and subsequent updates.
The following environmental data have also been taken into consideration for the design:
- wind load: 150 kg/m2.
- snow load: 300 kg/m2.
In cases where the actual values are higher than the theoretical data, the Customer must inform the
Manufacturer immediately.
4 1-Technical Catalogue
1-Technical Catalogue
SF.SPG35.T.A2.0911.EN 5
SF.SPG35.T.A2.0911.EN
6 1-Technical Catalogue
1-Technical Catalogue
SF.SPG35.T.A2.0911.EN 7
SF.SPG35.T.A2.0911.EN
MODULAR CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
SPG 35
35 = 35 m3 95 = 95 m3
50 = 50 m3 110 = 110 m3 Capacity
65 = 65 m3 125 = 125 m3
80 = 80 m3
1 = Standard Version
2 = Heavy
+ = Without Legs
1 = Standard
+++ = Without UF6 = Provision for FC2J13V Provision for filter
TSF = Exhaust pipe UF8 = Provision for FC3J20V
SIL = Provision
for Silotop
+ = Without Provision for VCP
1 = Provision VCP2731C
2 = Provision VCP3751C Provision for IPX
+ = Without
1 = IPX
+ = Without Filling
2 = Inlet spout 219
C= With filling pipe 114 pipe
3 = Inlet spout 273
1 = Inlet spout 168
+ = Without
1 = No.1 2 1/2 sleeve Sleeves (on cap)
2 = No.2 1 1/2 sleeves
3 = both sleeves
+ = Without
Flange at outlet
1 = Standard for V2FS300SN and V2FF300F19N
2 = For VLC/VLQ 300 (XKF751)
+ = Without 4 = 3950 mm
1 = 3660 mm 5 = 4050 to 4200 mm Connecting gangway
2 = 3750 mm 6 = 4200 to 4350 mm
3 = 3850 mm 7 = 4350 to 4500 mm
+ = Without
1 = Standard cycle Surface treatment
2 = High protection cycle
3 = Hot galvanization
2 = Ral 1013
6 = Ral 5012
D = Ral 5010
H = Ral 7032
G = Ral 7035 Shade
Q = Ral 7044
L = Ral 9001
M = Ral 9002
S = Ral 9016
V = Ral 9006 per T: 100-150
8 1-Technical Catalogue
1-Technical Catalogue
STANDARD SUPPLY
The standard supply of the Silo SPG35 consists of:
SF.SPG35.T.A2.0911.EN 9
SF.SPG35.T.A2.0911.EN
RANGE
3588
(external)
380
1158
SPG35.125
1508
SPG35.110
400
1508
SPG35.095
1508
SPG35.080
1508
12064
SPG35.065
10556
1508
9048
SPG35.050
H
7540
1508
6032
SPG35.035
4524
1508
3016
1508
400
2517
3917
1200
1400
RANGE: SPG35.035
3468
1150
400
3016
1508
2800
8241
7311
2517
400
2400
3420
2548
1400
1200
50
33
25
94
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.035 3468 35 37 33 11.85
SF.SPG35.T.A2.0911.EN 11
SF.SPG35.T.A2.0911.EN
RANGE: SPG35.050
3468
1150
400
4524
9749
1508
2800
8819
400
2517
2400
3420
2387
1400
1200
33
50
25
94
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.050 3468 50 51 47 11.85
12 1-Technical Catalogue
1-Technical Catalogue
RANGE: SPG35.065
3468
1150
400
6048
11257
10327
400
1508
2800
2517
2400
3420
2204
1400
1200
33
50
94
25
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.065 3468 65 65 61 11.85
SF.SPG35.T.A2.0911.EN 13
SF.SPG35.T.A2.0911.EN
RANGE: SPG35.080
3468
1150
400
7540
12765
11835
400
1508
2517
2400
3420
2588
1400
1200
33
50
25
94
2400
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.080 3468 80 79 75 11.85
14 1-Technical Catalogue
1-Technical Catalogue
RANGE: SPG35.095
3468
1150
400
9048
14273
13343
400
1508
2400
2517
3420
1956
1400
1200
50
33
2400 25
94
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.095 3468 95 93 89 11.85
SF.SPG35.T.A2.0911.EN 15
SF.SPG35.T.A2.0911.EN
RANGE: SPG35.110
3468
1150
400
10556
15781
14851
400
1508
2517
2400
3420
2249
1400
1200
50
33
2400 25
49
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.110 3468 110 107 103 11.85
16 1-Technical Catalogue
1-Technical Catalogue
RANGE: SPG35.035
3468
1150
400
12064
17289
16359
400
1508
2517
2400
3420
2632
1400
1200
50
33
2400 25
94
15
Nominal flow rate Max. theoretical flow Max. useful flow Min. useful flow
internal
Code [ m3 ] rate rate rate
[ mm ]
[ m3 ] [ m3 ] [ m3 ]
SPG35.125 3468 125 121 117 11.85
SF.SPG35.T.A2.0911.EN 17
SF.SPG35.T.A2.0911.EN
Seismic zone
Three versions are available, suitable for the following ag (horizontal seismic acceleration) values envisaged
by the European regulatory standards on the matter of seismicity.
Code Zone [ ag ]
S9 2 0.25 g
S6 3 0.15 g
S0 4 0.05 g
18 1-Technical Catalogue
1-Technical Catalogue
OPTIONS: Version
SF.SPG35.T.A2.0911.EN 19
SF.SPG35.T.A2.0911.EN
OPTIONS: Legs
SUPPORTING LEGS
Made of HEA sections.
The section depends on the size of the silo and its degree of earthquake resistance.
1- LEGS MADE OF HEA 140
The Table showing the specific models and plan drawing is given below.
92 115
2400
92
8
20
2
1
400
300
2400
115
300
400
23
2
92 115
2400
92
8
20
2
1
400
300
2400
115
300
400
23
2
20 1-Technical Catalogue
1-Technical Catalogue
400
65 87
2400
65
8
2
400
300
2400
18
87
2
300
21
3
WIND BRACING
The special layout of the wind bracing makes it possible to have a vast area through which the screw conveyors
can project out.
As a result, significant variations in the inclinations and lateral movements of the screw conveyors are permitted
at the work site
SF.SPG35.T.A2.0911.EN 21
SF.SPG35.T.A2.0911.EN
COVER
The dust filter is installed on this cover, if required.
15
1150
1200
1150
1100
1150
5
14
n.24
250
3
1200
In compliance with the current anti-pollution standards in force, it is obligatory to fit a dust removal system which
could be positioned on the ground or on the top of the silos.
1 - FILTER ON SILO
If positioned at the top of the silo, the material collected during the cleaning cycle is unloaded directly into the
silo. For more information on filters see page 48 .
NOTE: It is advisable to fit a separate filter on each silo.
The range includes three models.
Standard mounting position is shown below.
EXHAUST PIPE
It is necessary if the filter is positioned on a hopper placed on the ground. Silo and hopper will be connected by
means of a flexible duct. The product can be recovered by inserting a container under the hopper.
114.3
171
8
540
156
155 200
1
8
114.3
220
180
1
8
8
115.5
1200
XKF 10.1
L
Type Composition of outlet tubes
[ mm ]
SPG35.035 No. 1 x 6.020 6.020
SPG35.050 No. 1 x 6.020 No. 1 x 1.530 7.550
SPG35.065 No. 1 x 6.020 No. 1 x 3.040 9.060
SPG35.080 No. 1 x 6.020 No. 1 x 4.510 10.530
SPG35.095 No. 2 x 6.020 12.040
SPG35.110 No. 2 x 6.020 No. 1 x 1.530 13.570
SPG35.125 No. 2 x 6.020 No. 1 x 3.040 15.100
SF.SPG35.T.A2.0911.EN 23
5.0 OPTIONS
SF.SPG35.T.A2.0911.EN
The relief valve has the function of preventing pressure excesses, during the silos filling phase or fluidization
of material, or under-pressure during the emptying.
Two types of fitting are available for the relief valve:
25 25
- 273
- 375
A VCP pressure control valve is added to the stub pipe. For more information see page 48.
65
2
856
2200
65
65
50
120
120
4
273 356
24 1-Technical Catalogue
1-Technical Catalogue
6
321
196
n.6 8.5 220
holes
160
Bohrungen
trous
fori
25
50
R5
90
25
0
20
110
0
SF.SPG35.T.A2.0911.EN 25
SF.SPG35.T.A2.0911.EN
114.3
171
Composition of filling L
8
Type
540 pipes [ mm ]
156
1
8 SPG35.080 No. 1 x 6.020 No. 1 x 4.510 10.530
114.3 SPG35.095 No. 2 x 6.020 12.040
SPG35.110 No. 2 x 6.020 No. 1 x 1.530 13.570
220
SPG35.125 No. 2 x 6.020 No. 1 x 3.040 15.100
180
8
1
8
115.5
1200
XKF 10.1
221
B C Holes
centre internal
A
distance
Spout external No.
between
B
holes
0
R55
90
1428
26 1-Technical Catalogue
1-Technical Catalogue
25 25
65
2
856
2200
65
65
50
SF.SPG35.T.A2.0911.EN 27
SF.SPG35.T.A2.0911.EN
It is provided with four brackets, welded at 90 to one another, and the wind bracing must be bolted to these.
400
10
2517
1215
3917
272
249
8
1400
n.60
holes
Bohrungen
trous
fori
198
8
n.8 350
holes
Bohrungen
trous
fori
300
500
13
1913
2070
28 1-Technical Catalogue
1-Technical Catalogue
Some variations are available which, however, only concern the bottom cone.
CONE WITH FLANGE FOR VIBRATING BIN EXTRACTOR BA 150
454
1495
2"
OPTIONS: Fluidization
ACCESSORIES FOR FLUIDIZATION
In applications where a fluidization system is provided, the cones may be supplied with holes or sleeves, de-
pending on the type of fluidizer used.
1- HOLES FOR FLUIDIZERS
Suitable for plates and for vibrating bin aerators (for diameter, quantity and position, see attached Table). For
more information regarding fluidizers see page 48.
10
1215
272
30
60
0
0
9
71
63
5
2030
2- SLEEVES
FOR FLUIDIZERS
2.1-SIMPLE CONES
Dimension of sleeves 2. These are supplied complete with plugs.
In the order phase, the customer must inform the Manufacturer if 1 fluidization nozzles are to be used, so that
2 to 1 reductions can be supplied.
The positions of the holes are shown in the attached drawings.
Plates
Code
No. of Holes Dimensions of sleeves
M04 4
2
M08 8
30 1-Technical Catalogue
1-Technical Catalogue
Square flange
Suitable for gate valve
6
433
24 385 24
24
128.3
433
385
25
3
5
2.
1
n.60
holes
Bohrungen 24
trous flange
Round
fori
Suitable for butterfly valve
n.8 350
holes
Bohrungen
trous
fori 1 4
300
500
13
SF.SPG35.T.A2.0911.EN 31
SF.SPG35.T.A2.0911.EN
OPTIONS: Ladder
32 1-Technical Catalogue
1-Technical Catalogue
HOOP LADDER
1- LADDER
Used for reaching the top of the roof.
It is constructed according to the latest European provisions in terms of operator safety (consult page 5).
A hoop guard is provided 2000-2500mm from the ground.
The guard arches have a radius of 350 mm and are present every 1120 mm
The 450mm long steps are made of 3+2 non-slip checker plate or safety tread plate.
The inverted C shape facing downwards, the type of sheet metal used and the two side openings prevent
water and mud stagnation, ensuring the operator a safe hold while climbing up and coming down.
The centre distance between one step and the next is 285mm. The Table shows the distances of the rest land-
ing from the ground. According to the standards, this value must be < 10 m.
Type H [ mm ] Note
SPG35.035 / n.p.
SPG35.050 / n.p.
SPG35.065 4430
SPG35.080 5930
SPG35.095 7451
SPG35.110 6716
SPG35.125 8223
Its shape prevents the operator from leaning over dangerously beyond the guard while moving from the lower
ladder upwards. It may be defined as a safety cage.
2- SAFETY ACCESSORIES
2.1- Safety grille
Applied at the lower end of the ladder. Prevents access to the work site by outsiders. It must be fixed to the
bottom ring of the guard by means of a padlock.
2.2- Door for upper railing
Applied to the railing at the entrance to the ladder. Prevents accidental fall through it. (Fig. 1)
Fig.1 Fig.2
SF.SPG35.T.A2.0911.EN 33
SF.SPG35.T.A2.0911.EN
OPTIONS: Railing
A railing can be mounted at the top of the silos so that operators can move safely.
A railing is indispensable when it is necessary to get to the top of the silos with a certain frequency. It must
always be connected with the hoop ladder.
If no guards are present, the operator must use the necessary means for safe access to the roof.
1158
1158
158
158
158
Because of the modular composition the order can be placed depending on the number of openings necessary.
Ladders or gangways may be positioned at these openings.
Fig.1
34 1-Technical Catalogue
1-Technical Catalogue
Fig.2
Fig.3
Fig.4
SF.SPG35.T.A2.0911.EN 35
SF.SPG35.T.A2.0911.EN
Fig.5
Fig.6
36 1-Technical Catalogue
1-Technical Catalogue
Serves to connect the roofs of two or more silos positioned side by side. If the standard model is to be used,
while preparing the plant lay-out, make sure the fixed centre distance is 3660mm.
3660
Alternatively, it is possible to have the following centre distances (see Table 1):
I
Silos centre distances [ mm ]
3750
3850
3950
4050 to 4200
I
4200 to 4350
4350 to 4500
Tab. 1
SF.SPG35.T.A2.0911.EN 37
SF.SPG35.T.A2.0911.EN
SURFACE TREATMENT
EXTERNAL
+ = none (unfinished silo)
1 = Standard cycle
SA 21/2 + single-component synthetic alkyd primer (80 micron)
+ single-component alkyd enamel (40 micron)
(total thickness 120 micron)
2 = High protection cycle
SA 21/2 + epoxy primer containing zinc phosphate (80 micron)
+ bicomponent polyurethane enamel (40 micron)
(total thickness 120 micron)
3 = Hot galvanization
INTERNAL (standard)
SA 2 1/2 + single-component synthetic alkyd primer (80 micron thickness)
COLOUR
COLOUR RAL
2 RAL 1013
6 RAL 5012
D RAL 5010
H RAL 7032
G RAL 7035
Q RAL 7044
L RAL 9001
M RAL 9002
N RAL 9010
S RAL 9016
V RAL 9006 for T: 100-150 purple
38 1-Technical Catalogue
1-Technical Catalogue
Everytime the customer requires a distance of the outlet spout from the ground more than the standard (1,400
mm), the legs must be extended.
A maximum distance of 2,540 mm is permitted, which can be obtained by adding stub pipes of varying heights
(at 285 mm steps) as shown in the following diagrams.
For distances more than 2,540 mm an intermediate floor must be used.
Obviously it will be necessary to extend the hoop ladder, filling pipe and/or the exhaust pipe, if present .
15
1140
285
570
855
15
30 0
40 0
40
0
30
0
2
8
173
178
The stub pipes must be positioned as shown in the drawing. With this accessory and the wind bracings there
are no modifications.
standard leg
HEA220
SF.SPG35.T.A2.0911.EN 39
SF.SPG35.T.A2.0911.EN
Everytime the customer requires a distance of the outlet spout from the ground more than the standard (1,400
mm), the filling pipe and/or exhaust pipe will also have to be extended.
A series of extensions in various lengths are available.
3420
TPR35.3420 4820 XX
(1710+1710)
3990
TPR35.3990 5390 X X
(1710+2280)
4560
TPR35.4560 5960 XX
(2280+2280)
5130
TPR35.5130 6530 X X
(2280+2850)
5700
TPR35.5700 7100 XX
(2850+2850)
40 1-Technical Catalogue
1-Technical Catalogue
Ladder extension
60 x 2.9 mm
SF.SPG35.T.A2.0911.EN 41
SF.SPG35.T.A2.0911.EN
In applications where the distance of the outlet spout from the ground must be 3.1 and 7.1 m, supporting frames
can be used which can be combined appropriately to satisfy these needs.
For maintenance on machines downline of the silo (valves, fluidization, screw conveyors, etc.) an intermediate
floor consisting of a treading floor made of metal grating, surrounding protective railing and ladder for access
are available.
42 1-Technical Catalogue
1-Technical Catalogue
As shown in the following diagrams, there are three types, all made of HEA 220 sections.
h1
COMBINATIONS TABLE
The possible combinations are shown in the following Table:
SF.SPG35.T.A2.0911.EN 43
SF.SPG35.T.A2.0911.EN
From the treading floor it is possible to take the ladder to access the roof.
The treading floor is made of non-slip metal grating in order to prevent stagnation of water, snow or mud.
For intermediate heights, for e.g. 4.3 m, the raised feet Kit can be used (see page 40).
All the models are supplied dismantled and complete with nuts and bolts.
Obviously, if these accessories are present, the filling pipe and/or exhaust pipe will also have to be extended.
44 1-Technical Catalogue
1-Technical Catalogue
The accessories include two adapters: one for round clamped filter 1000, the other for a DUSTSHAKE
polygonal filter. For information regarding filters, see page 48.
SF.SPG35.T.A2.0911.EN 45
SF.SPG35.T.A2.0911.EN
INSPECTION COVER
Standard
485
100
2 1.5
400
n.15
holes
Bohrungen
trous
fori
Description
- Gasket on ETB65 ANTIOIL 4mm thick.
- No. 15 M8x20 screws (galvanized)
Finish
- Painted
ADHESIVE GASKET
ADHESIVE GASKET
The standard supply includes an adhesive gasket consisting of closed-cell polymer material.
If applied between the cylinder components, it isolates the material stored inside the silo completely from the
outside environment.
46 1-Technical Catalogue
1-Technical Catalogue
Butterfly valve
(cat. WA. 03041)
Round filter WAMECO
(cat. WA. 03505 T.)
Dust filter
DUSTSHAKE
(cat. WA. 03510.40 T.)
Butterfly valve
(cat. WA. 3010 T.)
Slide valve
(cat. WA. 03020)
SF.SPG35.T.A2.0911.EN 47
NOTE:. The data given in this catalogue are not binding and may undergo changes at any time.