Академический Документы
Профессиональный Документы
Культура Документы
Especificaciones generales.
GEOMETRIA ESTRUCTURAL.
SECC. VIGAS…………0.30X0.60
SECC. COLUMNAS……0.40X0.40
LOSAS……………..E= 0.16 mt
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
ANALISIS GENERAL DE CARGAS EN LOSAS.
D) PANDERETAS ……………………………………..0.100
E) PAÑETE………………….0.01 X 2.00……………0.020
TOTAL……0.645 T/M2
TECHO: C.M = 0.604 T/M2
C.V = 0.250 T/M2
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
ENTREPISO: C.M = 0.645 T/M2
C.V = 0.250 T/M2.
ANALISIS SISMICO
PARAMETROS SISMICO.
U=1
S=1.50
Z= 1
R= 7
T=0.60 SEG.
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
CARGA PERMANENTES POR PISO:
Wm4 = Wm techo = (21.6 X 12.25 – 3.40 X 5.35 ) X (0.604) + ( 14 X 0.40X 0.40 X 2.4 ) X (0.5 X 3.5)
Wm1 = 246.41 x 0.645 + 5.376 ( 0.5 ) x ( 3.5 + 5 ) + 0.432 x 111.15 = 229.80 ton.
ENTREPISO = 0.20
TECHO = 0.10
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
W1 = 229.80 + 61.60 X 0.20 = 242.12 ton.
Wt = 930.72 ton.
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
ETABS 2000 V8.0
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
- COMBO……ADD. DEAD, CM, CV Y SISMO.. PARA ESTA COMBINACION
DE CARGAS.
- Poner similar stories y seleccione toda la estructura en plan view
story 4 – elevation 15.5 , esto equivale a seleccionar todas las vigas. Y
assign…..frame/line…..frame section…..viga; luego en draw…draw
line objecto…..draw lines……en property poner viga y poner el
puntero en grid point c3.. hasta c5. para modelar la viga que faltaba;
entonces en draw area objecto…..draw rectangular areas ….y arrastre
el puntero en dos puntos hasta completer los otros dos nodos de la
losa, y asi sucesivamente modelar todas las losas de la estructura,
menos el recuadro o espacio de la escalera; en set building view
options chequear object fill y sin chequear invisible. Luego en 3D
VIEW hacer lo mismo. Y o.k…
- En 3DVIEW….SELECT……BY LINE OBJECT TYPE….COLUMN
- ASSIGN…..FRAME/LINE…..frame section… columna….o.k
- SELECCIONAR LAS LOSAS DEL TECHO Y
ASSIGN…SHELL/AREA
LOADS….UNIFORME…..CM……0.604…Y CV….0.250 TON/M2
- SELECCIONAR LAS LOSAS DEL ENTREPISO Y
ASSIGN….SHELL/AREA
LOADS……UNIFORME…CM…0.645…Y….CV…0.250 TON/M2.
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
SELECCIONE TODAS LAS LOSAS DEL MODELO ESTRUCTURAL Y
ASSIGN….SHELL/AREA….RIGID DIAPHAGM…O.K.. Y DE NUEVO
ASSIGN…..SHELL/AREA….AREA OBJECT MESH OPTIONS….AUTO MESH OBJECT INTO
STRUCTURAL ELEMENTO.. Y CHEQUEAR TODO….OK
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
ANALISIS DE LA ESTRUCTURA
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
ANALISIS DE LA ESTRUCTURA Y VER LOS RESULTADOS Y CHEQUEAR EL
DESPLAZAMIENTO EN LA PUNTA DE LOS PORTICOS, PUES ES UNA MEDIDA
DE LA DUCTILIDAD GLOBAL DE LA ESTRUCTURA. Y CHEQUEAR LAS
DISTORSIONES DE PISO O DERIVAS.
Antes de diseñar los elementos estructurales debemos chequear los desplazamientos y las
distorsiones de piso. [deriva]. Si no chequean con las normas, se debe rigidizar la
estructura, con muros estructurales o brazos rigidos.
Este analisis y diseño de la estructura fue preliminar, como sabemos que las
secc. de vigas y columnas chequean, entonces analizamos la estructura
general por medio del programa etabs 2000.
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
En la estructura deformada , se produce el mayor desplazamiento=
0.33cm…….ok…………….< luz total en direccion x-x / 480…….OK
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete
EN ESTE NIVEL ES BUENO HACERLE UN ANALISIS DINAMICO A LA
ESTRUCTURA, USANDO UN COEFICIENTE PARA EL ESPECTRO.
FACTOR = CORTANTE BASAL ESTATICO/ CORTANTE BASAL DINAMICO.
LUEGO HACERLE UN PUSHOVER A LA ESTRUCTURA.
www.cadfamily.com contact:cadserv21@hotmail.com
The document is for study only,if any tort to your rights,please inform us,we will delete