Академический Документы
Профессиональный Документы
Культура Документы
8
Company: Page: 1
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200-A + HIT-V-F (8.8) M16
Effective embedment depth: hef,opti = 80 mm (hef,limit = 264 mm)
Material: 8.8
Evaluation Service Report: ETA 11/0493
Issued I Valid: 8/8/2012 | 12/23/2016
Proof: design method ETAG BOND (EOTA TR 029)
Stand-off installation: eb = 0 mm (no stand-off); t = 17 mm
Anchor plate: Custom; E = 205000.00 N/mm2; fyk = 275.00 N/mm2
lx x ly x t = 150 mm x 260 mm x 17 mm; (Recommended plate thickness: calculated)
Profile: Advance UKB; (L x W x T x FT) = 251 mm x 146 mm x 9 mm x 9 mm
Base material: cracked concrete, , fcc = 40.00 N/mm2; h = 300 mm, Temp. short/long: 0/0 C
Installation: hammer drilled hole, installation condition: dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm)
no longitudinal edge reinforcement
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk Profis Anchor 2.4.8
Company: Page: 2
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk Profis Anchor 2.4.8
Company: Page: 3
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are
valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in
this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk Profis Anchor 2.4.8
Company: Page: 4
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
7 Warnings
Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger diameters of
the clearance hole see Chapter 1.1. of EOTA TR029!
The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be
followed to ensure a proper installation.
Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice, blow
twice with oil-free compressed air (min. 6 bar)).
Characteristic bond resistances depend on short- and long-term temperatures.
Please contact Hilti to check feasibility of HIT-V rod supply.
Edge reinforcement is not required to avoid splitting failure
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk Profis Anchor 2.4.8
Company: Page: 5
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
8 Installation data
Anchor plate, steel: Custom; E = 205000.00 N/mm2; fyk = 275.00 N/mm2 Anchor type and diameter: HIT-HY 200-A + HIT-V-F (8.8) M16
Profile: Advance UKB; 251 x 146 x 9 x 9 mm Installation torque: 0.080 kNm
Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm
Plate thickness (input): 17 mm Hole depth in the base material: 80 mm
Recommended plate thickness: calculated Minimum thickness of the base material: 116 mm
Cleaning: Premium cleaning of the drilled hole is required
75 75
65
3 4 130
130
x
130
1 2
65
25 100 25
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk Profis Anchor 2.4.8
Company: Page: 6
Specifier: Project: PACKAGE-C, AL-THUM
Address: Sub-Project I Pos. No.: UB254X146X31
Phone I Fax: | Date: 11/6/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan