Академический Документы
Профессиональный Документы
Культура Документы
Stage 1Separation
Using the fuel flow, the stationary
turbine separates large solids and
free water through enchanced
centrifugal force.
Stage 2Coalescing
Smaller water droplets and solids
coalesce on the conical baffle and
fall to the collection bowl.
Stage 3Filtration
Engines will benefit from near
100% water separation and fuel
filtration with Racors proprietary Contact Information
RINE
Aquabloc water repelling media. MA
The replaceable filters are Parker Hannifin Corporation
available in 2, 10, and 30 micron Racor Division
P.O. Box 3208
TY P E
CT
ratings.
3400 Finch Road
DU
PP
A
RO V E D P R Modesto, CA 95353
ABS/BV Phone 800 344 3286
209 521 7860
Fax 209 529 3278
Email racor@parker.com
Web parker.com/racor
Mounting Information
5.8 in. 5.8 in.
(14.7 cm) (14.7 cm)
900 Models 1000 Models
4.5 in
(11.4 cm)
5.0 in
11.0 in (12.7 cm)
4.5 in
(27.9 cm)
(11.4 cm)
Adjustable to
13.5 in
(34.3 cm)
10.9 in
V (27.7 cm)
10 10
Adjustable
by 2.1 in.
90 (5.3 cm)
Note: Mount filter assembly as close to vertical (V) as possible.
Do not exceed 10 from vertical or assembly may not function
properly. Fastener size is 3/8" (M10) for mounting brackets.
Installation Diagram
Fuel tanks above filter
Optional Bypass Installation and Operation Maintain a clearance head pressure should not
(allows user to service filter without shutting down engine.) above the filter assembly exceed maximum PSI of filter.
Valves 1 2 3 of 5 in. (12.7 cm) (900MA),
and 10 in. (25.4 cm) (1000MA)
Unit On-line Open Open Closed for filter removal. Fuel Tank
Unit Off-line Closed Closed Open (Pressure Side Installation)
Pressure Side:
Fuel transfer pump not to exceed
maximum PSI or flow rate of filter.
Not ideal - pumps emulsify water
Suction (vacuum) Side: hindering filter performance. Install a shut-off valve when
Primary (first) filter - use 30 micron. fuel tank is higher than filter
If it is the only filter in the system,
use 2 or 10 micron.
Fuel Tank
Engine (Ideal Vacuum
Side Installation)
Valve 2 Valve 1
Service Instructions
Draining Water Suction Side Pressure Side
Frequency of water draining is Applications Applications
determined by the contamination
level of the fuel. Inspect or drain 1. C
lose inlet valve (or valve #1) 1. Open self-venting drain
collection bowl of water daily or as and open self-venting drain on on bottom of bowl. Head
necessary. Collection bowl must bottom of bowl. pressure will push any water
be drained before contaminants and contaminants out of drain
reach the bottom of the turbine 2. C
lose drain after all water while keeping filter primed.
(inside the bowl), or when the and contaminants have been
2. Close drain after all water
Water Detection Module (optional) evacuatedDO NOT leave
and contaminants have been
indicates a drain is required. drain open too long as it will
evacuatedDO NOT leave
eventually completely drain
drain open too long as it will
entire filter of water AND fuel.
eventually completely drain
3. Follow Priming Instructions. entire filter of water AND fuel,
and possibly drain entire tank.
Filter Replacement
Frequency of filter replacement is All Applications debris. Lubricate new gasket
determined by the contamination and seal (supplied with new
level of your fuel. Replace filter 1. Isolate the filter assembly with filter) with motor oil or diesel
every 500 hours, every other oil bypass or shut-off valves, if fuel before installation.
change, when vacuum gauge applicable. 5. Refer to Priming Instructions,
(optional) reads between 7 to otherwise, fill unit with clean
10 inches of mercury (inHg), if 2. Remove T-handle and lid.
fuel, replace lid and T-handle
power loss is noticed, or annually,
3. Remove filters by holding bail and tighten snuggly by hand
whichever occurs first.
handles and slowly pulling onlydo not use tools.
Notealways carry extra upward with a twisting motion. 6. Open any closed valves; if
replacement filters as one tankful Dispose properly according to applicable.
of excessively dirty fuel can plug local regulations.
a filter. Noteabove ground tanks or
4. Remove and discard old lid transfer pump applications may
Use only genuine Racor Aquabloc gasket and T-handle O-ring and use head pressure to prime filter
replacement filterssee Part List. clean seal glands of any dirt or assembly.
Specifications
900MA 1000MA
or or
900MAM 1000MAM
Maximum Flow Rate: 90 GPH (341 LPH) 180 GPH (681 LPH)
1a
2
Part Number Description
2a
T-handle and O-ring Kit (includes 1a)
RK 11-1945 (Brass)
1 (9/16-18 UNF Threads)
RK23183 (Stainless Steel)
Hand Tighten
1a RK11350 T-handle O-ring
2 RK 11-1933-04 Lid Kit (includes 2a) 3
2a RK11007 Lid Seal
2040N-02 (2 micron), or
2040N-10 (10 micron), or 900MA/MAM (includes 2a)
2040N-30 (30 micron)
3
2020N-02 (2 micron), or
4
2020N-10 (10 micron), or 1000MA/MAM (includes 2a)
2020N-30 (30 micron)
RK11-2006 900MA/MAM Clamp Bracket Kit
4 A
RK11-2008 1000MA/MAM Double-welded Clamp Bracket Kit
900MA/MAM Body/Housing 5a 5
A (not sold seperately)
1000MA/MAM Body/Housing
Feed-thru Plug Kit (includes 5a)
5 RK 11-1679
Tighten 15 in. lbs (1.69 Nm) max.
5a 43506 Plug O-ring
6 Check Ball Seal 6
RK 11028B
7 Check Ball 7
Hand tighten T-handle only! Do not Replace T-handle o-ring and lid
use tools for leverage. gasket with each filter element
replacement.