Академический Документы
Профессиональный Документы
Культура Документы
A-60 Marine
Fire Damper
Designed for inclusion in Marine
and Offshore Projects.
Suitable for applications in
A0, A15, A30, & A60 Class Divisions
Bulkheads and Decks.
Blades
430 stainless steel and 316 stainless
steel options.
Casings
Lightweight cost effective design.
Rectangular and circular flanges.
Galvanised and 316 stainless steel
options.
1.2, 2, and 3mm options.
150 and 210mm depths.
Standard and customer flange drilling
options.
Visual indicator option.
Atex rating option.
Actuators
Electrical
24V, 120V and 230V options.
Pneumatic ATEX (Ex) rated
3 second reset time.
PTR release.
ATEX (Ex) rated (Electrical)
Universal voltage 24V - 230V AC/DC,
with 1 second reset time option.
actionair
Ruskin Air
actionair Air Diffusion naco
Management
www.actionair.co.uk
A-60 Marine Fire Damper
Introduction Specification
Actionair has, for many years, been Electrical Testing - Maintenance and cleaning
associated in the design, The Actionair direct-coupled spring return
A-60 Dampers are supplied in 2 casing and
development and manufacture of life fail-safe electrical control modes are fitted
blade options:-
safety equipment, including the with halogen free low smoke and fume
supply of fire damper products to the electrical cable. They have a 60 second reset 1. 430 Standard steel blades, Galvanised
offshore and marine industry. The time and a 20 second release time. Each Steel casing - only suitable for installation in
Actionair A-60 Marine Fire Damper actuator has a 72 C rated Electrical Thermal dry filtered systems.
has been specifically engineered to Release (ETR). The ETR incorporates a
meet stringent legislation. safety electrical interlock that only permits 2. 316 Standard steel blades, casing and
actuator operation when correctly fitted. A drive - more suited for corrosive conditions,
The A-60 Marine Fire Damper green 'Healthy' indication lamp is built into but even this will rapidly corrode and fail if
compliments the comprehensive the ETR housing to give a simple and clear not properly maintained, when used in air
range of automatic fire and smoke visual check that the actuator is receiving intake systems at sea. The addition of a
dampers and associated controls, power, the ETR is correctly fitted and the DB50 Storm Louvre (page 17) is highly
provides the complete solution for thermal fuse is intact. A manual test switch recommended and access must be
shipboard air conditioning and allowing periodic operation of the damper for provided for maintenance.
ventilation systems fire safety testing purposes simulates actual fail-safe Pay particular attention to the blade rivets,
engineering strategies. release under smoke/fire conditions. End where crevice corrosion will cause rapid
switches are provided with each mode for failure of blades if not kept in check.
The A-60 Marine Fire Damper has reset and release monitoring.
been designed for inclusion in air Testing
Electrical ATEX (Ex) rated Two levels of testing exists.
conditioning and ventilation systems,
The Actionair direct-coupled spring return
in dry filtered air, and is tested and 1. Routine testing
fail-safe ATEX (Ex) electrical control modes
approved for fitting to class A-60 Monthly, or in accordance with
are fitted with 1 metre of cable for
divisions (bulkheads and decks), maintenance programme, release and reset
connection inside hazardous areas.
when suitably insulated (refer to damper (via control system or ETR test
They have the benefit of a universal electrical
insulation details). switch). Check remote indication or visual
supply using any Voltage between 24-230V
AC/DC, which is self adaptable. They have check of mechanical pointer as appropriate.
variable (3 -15 -30 - 60 -120 sec) reset and 2. Visual check at damper
(3 -10 sec ) release times, which are At commissioning and at least once a year,
selectable on site. Each actuator has a check damper operation by removing and
Integral Safety Temperature Sensor (ExPro- re-applying power to actuator. (via ETR test
TT) rated at 72 C. The ExPro-TT switch). Visually check blades for damper
incorporates a triple fail-safe thermal fuse closed and open positions. Prove remote
arrangement, 2 induct and one outside, to indication if applicable.
ensure the fail-safe control mode operates in
all conditions. A manual test switch allowing Routine Maintenance
periodic operation of the damper for testing Depending upon environmental conditions,
purposes simulates actual fail-safe release each damper will merit its own cleaning
under smoke/fire conditions. End switches regime. Particularly hostile areas may
are provided with each control mode for require monthly cleaning and lubrication.
reset and release monitoring. An Integral Frequency of maintenance should be
heater allows the unit to be operated within determined by collecting historical data
ambient temperatures down to 40C. from previous visits, and for this reason,
Pneumatic ATEX (Ex) rated commence maintenance programmes at
The Actionair direct coupled spring return very frequent intervals. Dampers in Dry
fail-safe pneumatic control mode requires an Filtered Air require very limited
air pressure of between 5 to 8 bar (72 to maintenance.
116 psi) to operate. They have 3 second Using Duck Oil (recommended lubricant, or
reset and release time. Each control mode similar equivalent), clean all exposed
has a Pneumatic Thermal Release (PTR). surfaces, using a cloth. Remove all traces
The PTR assembly is supplied with 500mm of surface staining, as this will deteriorate
nylon tubing that connects to the quick fit further causing deeper material corrosion.
couplings of the PTR and control mode.
Incorporated is a fail-safe 74 C fusible link. If damper is stiff to operate, lubricate blade
When this operates, air exhausts from the ends and open and close damper
control mode, permitting the spring return successively until the damper moves with
All certificates are action to the fail-safe position, thus closing ease. (This may necessitate removal of the
available via the the damper. Switch box and solenoid actuator and operating the blades manually
Actionair website. accessories are available for monitoring and by the drive shaft). Refit actuator, and re-
www.actionair.co.uk control. test. Clean off excessive lubricant.
2
A-60 Marine Fire Damper
Application
Casing Features
1.2mm galvanised steel or 316 grade (type
1.4401) austenitic stainless steel flanged 2mm and 3mm Casing Casing Mounted ETR
type casing, (optional 2mm and 3mm - 210mm deep casings only
thick), having a single penetration for the
Factory fitted Actuator Options (Electrical only) - 210mm deep casings only
drive control, complies to Class A & B of
Eurovent 2/2 and Test Procedures for
Classes A, B, & C of the HVCA Ductwork
Specification DW144.
Pre-punched bolt holes are provided as
standard (refer to page 11).
In addition stainless steel peripheral
gasketing is included, which allows for
expansion under full fire conditions.
The 1.2mm casing has obvious benefits,
for example being lighter in weight,
allowing easier installation.
A-60 Electrical with fitted ETR A-60 Electrical Atex with ExPro-TT
Blade Features
The damper blades are aerodynamic double
skin at 75mm pitch which when closed,
interlock to form a positive fire resisting shield:-
430 grade (Type1.4016) ferritic stainless steel Optional Silicon blade seals can be
with sintered steel with steam oxide and oil provided for low leakage requirement
dipped finish blade end bearings (available at ambient temperature.
with galvanised casing only).
41.5
316 grade (Type 1.4401) Austenitic stainless
steel with sintered 316 austenitic stainless
12.7
steel blade end bearings.
Blades are 0.5mm thick of double skin
75
construction.
actionair 3
A-60 Marine Fire Damper
Insulation Details
or CUBIC METRE)
240 See Below
**
40
**
50
See Below
**
300
240
or
See Below
DAMPER COAMING
40
25
See page 11
40 25
CONNECTION
CONNECTION OF DAMPER MINERAL FIBRE INSULATION OF DAMPER
50 40
TO COAMING (110Kg PER CUBIC METRE) TO COAMING DAMPER
Graph showing Minimum Insulation length for Damper above 750mm x 750mm Base Damper
(Applies to all approval bodies with the exception of ABS)
00 Coaming Insulation
Example
050
For a damper size of 910mm x 925mm.
Total Insulation length (mm)
000
Area = 0.85 msq
Vertical Installation
50 Insulation Thickness = 75mm
(line 2 of table above)
00 Insulation Length = 975mm (refer to graph)
850
Horizontal Installation
Insulation Thickness = 40mm
800
(line 4 of table above)
Insulation Length = 975mm (refer to graph)
50 Insulation Thickness = 75mm
(line 5 of table above)
00
0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 0.95 1 Insulation Length = 725mm
Area (msq) (line 5 of table above)
4
A-60 Marine Fire Damper
Testing
The Actionair A-60 Marine Fire Damper Tests, approvals and certification Transport CANADA Type Approved.
has undergone extensive fire testing in Marine Equipment Directive (MED) 96/98/EC Corrosion Tested to BSEN 60068-2-52,
single and multiple arrangements. The severity 2 conditions.
dampers were incorporated in steel Lloyds Register Approval to IMO Fire Test
bulkheads and decks and tested to the Procedures Code, Annex 1, Part 3, for Class Vibration Tested to BS EN 60068-2-6 (5Hz to
Marine Fire Resistance Test in A0, A15, A30 & A60 Division bulkheads and 350Hz @ 2g).
accordance with IMO resolution A754. decks. In compliance with the Applicable Sira Certification (Ex) category 2 equipment.
(18) for a duration of 60 minutes. Lloyds Register Rules and Regulations and
EC Type Examination (Module B) Certificate
Changes to the originally supplied with the International convention for the Safety
Of Life At Sea (SOLAS). EC (Module D) Certificate of Conformity.
product may invalidate the certification
and/or warranty. DNV (Det Norske Veritas) Type Approved. Certificate of Fire Approval.
ISO 9001:2008 Certification.
USCG (United States Coast Guard) approved
(product category 164.139). Copies of all certification are available from our
website.
Germanischer Lloyds approved to IMO Res.
A.754 (18) and IMO Res. MSC61(67), Annex 1 Changes/Modifications to the original supplied
Part 3. product may invalidate certification and/or
warranty.
ABS (American Bureau of Shipping) approved
to 2005 Steel Vessel Rules 1-1-4/7.7 (Please
note maximum size restrictions see page 4).
actionair 5
A-60 Marine Fire Damper
155
positive connection system. This allows the
Position 1
dampers and actuators to be supplied
separately, offering shipping and storage
30
benefits. 100
Position 3 123
DAMPER HEIGHT
Three Position
Universal
Fig. 2 Position 2
248
400
Three Position
Position 1
Compact
Fig. 1
100
100
Electrical
TEST SWITCH LED LAMP Fail-safe is by means of a unique and purposes, simulating actual fail-safe release
patented Electrical Thermal Release (ETR) under fire conditions.
which operates at 72 C, or if power supply
The associated electrical Control Modes are
CAP is interrupted. The ETR incorporates a
available in 24V, 120V or 230V versions.
safety feature, that ensures the fail-safe
status of the damper if the ETR is not Also available with 95 Probe as an option.
fitted on to the ductwork. Additionally a Probe section only available as a spare
green LED lamp is built into the ETR replacement part.
housing. This gives the user a simple and
clear visual check that the Actuator is
receiving power, the ETR is correctly
fitted, and the thermal fuse is intact.
A manual test switch allows periodic
PROBE
operation of the damper for testing
6
A-60 Marine Fire Damper
24V - AC - 50/60Hz
AC 19.2 - 28.8V 1
VOLT FREE
DC 21.6 - 28.8V CONTACT MADE BETWEEN
2
230V 196 - 264V 1 AND 2 WHEN DAMPER
120V 96 - 132V 3 FULLY RELEASED
12.5 V A
AC 4 VOLT FREE
Supply On - Damper motors open Max
10 / 2 W 250V CONTACT MADE BETWEEN
Supply Off - Damper springs closed 6(3)A 5
4 AND 6 WHEN DAMPER
ETR Operates - Damper springs closed Imax FULLY RESET
8.3A @ 5ms 6
1
VOLT FREE
2 CONTACT MADE BETWEEN
1 AND 2 WHEN DAMPER
3 FULLY RELEASED
4 VOLT FREE
AC CONTACT MADE BETWEEN
5
14 V A 250V 4 AND 6 WHEN DAMPER
Max
6(3)A FULLY RESET
12 / 4 W 6
ELECTRICAL THERMAL
TF 72 C RELEASE (MUST BE FITTED
FOR DAMPER OPERATION).
30...+50 C
CONTINUOUS (SPRING BIASED
TEST SWITCH)
actionair 7
A-60 Marine Fire Damper
The ATEX rated control modes, are The control modes are direct coupled to
located outside of the ductwork for ease the damper utilising a unique user friendly
of access and installation. positive connection system. This allows
the dampers and control modes to be
Control modes can be fitted in any one supplied separately, offering shipping and
of three orientations, i.e. vertically down, storage benefits.
horizontally or vertically up. Positions 1,
2, or 3.
MOUNTING MOUNTING
PLATE BRACKET
DAMPER
DRIVE
SHAFT
Position 3
44
231
Position 2
97
ExPro-TT Position 1
ExPro-TT
8
A-60 Marine Fire Damper
Atex (Ex) Rated Electrical Control Modes On-off 1-wire-spring return + Ex-i circuit
Universal supply unit from 24 to 230V-AC/DC, 50/60 Hz. Ex-i circuit for
Integrated aux, switches
max 24V/3A, 240V/0.25A passive + potential
Supply On - Damper motors open. min. 5V/10mA, switching free push button on
Supply Off - Damper springs closed. at 5 and 85. site and safety
Supply at aux. switches temperature sensor
ExPro-TT Operates - Damper springs closed.
must be the same like (Type ExPro -TT
20W (Maximum Blocking), supply of the actuator accessories)
24...240 VAC/DC
+ Attention
16W (Heater). ~ ~ If you use this < 5 < 85
ExPro -TT
type of wiring the
End Switches Rated at 250V 1.5 Amp (Maximum). heater does not
PE C
work in case of
To isolate from main power supply, the system must incorporate open contact
a device, which disconnects the phase conductors, with at least
Push button
3mm contact gap.
Power input depending on supply voltage Dimensioning of the line cross section with 24 to
Power supply design
48 Volt AC/DC supply voltages
The design of the on-site supply, depends on the selected motor Dimensioning / Design of the supply line
running time and selected supply voltage. Accompanying values On long distances between supply and actuator, voltage drop
are about values, since there can be construction unit occurs due to line resistances. On 24V AC/DC systems the
dispersions within electronics. The power consumption in the actuator receives a low voltage and does not start. In order to
blocking position is run time independently with max 20W. The prevent this, the cross section of the inlet line is to be
power consumption for the heater is approximately 16W. The designed/dimensioned accordingly. The accompanying formula
heating is running only if the motor is in idle position. The initial allows the calculation of the required line cross section area and
starting supply voltage required by the actuators power supply indicates the maximum length utilising an existing line.
unit is around 2.0A for about 1 sec. (Please consider this while Alternatively the secondary voltage can be increased by selecting
calculating the cross section area of the supply line.) a transformer to overcome the loss.
For calculation purposes, following characteristics are essential:
Rated current in acc. with motor running time UV = supply voltage in [V]
Voltage Current 3/7,5s 15s 30s 60s 120s A = line cross section in [mm2]
L = line length in [m]
230V Irated 0.5A 0.3A 0.15A 0.10A 0.10A
Factor 0.0714 = drive-specific factor
120V Irated 0.75A 0.4A 0.3A 0.25A 0.25A [Vmm2/m] 9 based on the electrical conductivity of copper with a
48V Irated 2.0A 0.5A 0.3A 0.2A 0.2A coefficient of 56/Wmm2)
24V Irated 4.7A 1.45A 0.52A 0.4A 0.4A
Panel
Line cross section A [mm2]
Terminal box Actuator
Uv [m] .75 1mm2 1.5mm2 2.0 2.5mm2 Voltage
28 Uv [V]
27 Lenght L [m]
26
25 4mm2 Formula for maximum cable Formula of needed cable
24
length L at cable cross cross section A at a cable
23
section A length of L
actionair 9
A-60 Marine Fire Damper
Pneumatic
The special purpose design Pneumatic 74 C Pneumatic Thermal Release (PTR). 4mm diameter tubing 500mm
Thermal Release (PTR) assembly is length connection to actuator
Air pressure = 5.5 - 8.0 Bar.
supplied with 500mm nylon tubing that
connects to the quick fit couplings of the External mechanical position indicator.
PTR and control mode. Incorporated is a Test operation by removing fusible link
failsafe 74C fusible link. When this element.
activates, air exhausts from the control
mode, enabling the PTR to spring return to
the fail-safe position, thus closing the Pneumatic Thermal Release (PTR)
damper.
The control modes are coupled to the
damper using a friendly connection
system. This allows the damper actuator 2 off quick Input:
and the PTR to be supplied separately, release 6mm diameter,
offering shipping and storage benefits. connectors, quick release
supplied connector,
pressure range
Pneumatic Operation 5 - 8 Bar
Air On - Damper opens.
Air Off - Spring closure.
Release time 2 - 4 secs.
Reset time 2 - 4 secs.
Air inlet 6mm dia. quick fit coupling.
Dimensional Data
Festo Actuator with Solenoid and Status Beacon
236
25
204
104
84
MINIMAL REMOVAL
DISTANCE 224mm
153 40
10
A-60 Marine Fire Damper
FRONT FRONT
FLANGE ALL
ROUND
MAX
MIN
150
75
40
TYPICAL
HOLE DIM.
20
40
20 DIA. + 40mm SEE TABLE
100 - 1000
TYPICAL BELOW
79
98
Multiple Assemblies
75mm WIDE
JOINING STRIP. (BOTH SIDES)
RIVETTED WITH 3.2mm STEEL
RIVETS AT 100mm CENTRES,
150
210
ON SITE BY OTHERS
or
51 TOP
ACTUATOR ACTUATOR
DAMPER HEIGHT
750 Maximum
FRONT FRONT
TYPICAL
20
20
TYPICAL 12mm Holes
actionair 11
A-60 Marine Fire Damper
Weights
1.2mm Galvanised Casings, 150mm Deep
Weights
Weights (kg) of A-60 Rectangular (Excluding Actuator) (kg) of A-60 Circular
100 200 300 400 500 600 700 800 900 1000 (Excluding Actuator)
100 3.0 3.8 4.6 5.5 6.3 7.1 8.0 8.8 9.7 10.5 100 Dia. 4.6 Compact Including Adaptor Plate 1.85kg
200 4.1 5.0 5.9 6.9 7.8 8.7 9.6 10.5 11.4 12.3 200 Dia. 8.1 Universal Including Adaptor Plate 3.00kg
300 5.3 6.4 7.4 8.4 9.5 10.5 11.5 12.6 13.6 14.7 300 Dia. 12.0 Pneumatic Including Adaptor Plate 3.00kg
400 6.2 7.3 8.4 9.5 10.6 11.7 12.8 13.9 15.0 16.1 400 Dia. 15.4 Electrical Atex Including Adaptor Plate 3.50kg
500 7.4 8.6 9.7 10.9 12.1 13.3 14.4 15.6 16.8 18.0 500 Dia. 19.8
600 8.6 9.9 11.2 12.5 13.8 15.1 16.4 17.7 19.0 20.4 600 Dia. 24.6
700 9.5 10.9 12.2 13.6 15.0 16.3 17.7 19.1 20.5 21.8 700 Dia. 28.9
800 10.3 11.8 13.2 14.7 16.1 17.5 19.0 20.4 21.9 23.3 800 Dia. 33.6
900 11.5 13.1 14.7 16.3 17.8 19.4 21.0 22.6 24.1 25.7 900 Dia. 39.4
1000 12.4 14.1 15.7 17.4 19.0 20.6 22.3 23.9 25.6 27.2 1000 Dia. 44.5
100 4.1 5.3 6.4 7.6 8.8 10.0 11.1 12.3 13.5 14.7 100 Dia. 6.1 Compact Including Adaptor Plate 1.85kg
200 5.6 6.8 8.1 9.3 10.5 11.8 13.0 14.3 15.5 16.7 200 Dia. 10.7 Universal Including Adaptor Plate 3.00kg
300 7.1 8.4 9.8 11.2 12.6 13.9 15.3 16.7 18.0 19.4 300 Dia. 15.6 Pneumatic Including Adaptor Plate 3.00kg
400 8.2 9.7 11.1 12.5 14.0 15.4 16.9 18.3 19.7 21.2 400 Dia. 20.1 Electrical Atex Including Adaptor Plate 3.50kg
500 9.8 11.3 12.8 14.3 15.8 17.3 18.8 20.3 21.8 23.3 500 Dia. 25.6
600 11.3 12.9 14.5 16.2 17.8 19.5 21.1 22.8 24.4 26.0 600 Dia. 31.6
700 12.4 14.2 15.9 17.6 19.3 21.0 22.7 24.4 26.1 27.8 700 Dia. 37.0
800 13.6 15.4 17.2 18.9 20.7 22.5 24.3 26.1 27.8 29.6 800 Dia. 43.0
900 15.1 17.0 18.9 20.9 22.8 24.7 26.6 28.5 30.4 32.3 900 Dia. 50.1
1000 16.3 18.3 20.3 22.2 24.2 26.2 28.2 30.2 32.1 34.1 1000 Dia. 56.4
100 5.5 7.1 8.7 10.3 11.9 13.5 15.1 16.7 18.3 19.9 100 Dia. 8.4 Compact Including Adaptor Plate 1.85kg
200 7.4 9.1 10.7 12.4 14.0 15.7 17.4 19.0 20.7 22.4 200 Dia. 14.5 Universal Including Adaptor Plate 3.00kg
300 9.3 11.1 12.9 14.7 16.5 18.2 20.1 21.8 23.6 25.4 300 Dia. 21.1 Pneumatic Including Adaptor Plate 3.00kg
400 10.8 12.7 14.5 16.4 18.3 20.1 22.0 23.9 25.7 27.6 400 Dia. 27.3 Electrical Atex Including Adaptor Plate 3.50kg
500 12.7 14.7 16.6 18.5 20.5 22.4 24.3 26.3 28.2 30.1 500 Dia. 34.5
600 14.6 16.7 18.7 20.8 22.9 24.9 27.0 29.1 31.1 33.2 600 Dia. 42.4
700 16.2 18.3 20.4 22.6 24.7 26.8 29.0 31.1 33.3 35.4 700 Dia. 49.7
800 17.7 19.9 22.1 24.3 26.5 28.7 31.0 33.1 35.3 37.6 800 Dia. 57.6
900 19.6 22.0 24.3 26.6 29.0 31.3 33.6 36.0 38.3 40.7 900 Dia. 66.7
1000 21.2 23.6 26.0 28.4 30.8 33.2 35.6 38.0 40.4 42.8 1000 Dia. 75.1
12
A-60 Marine Fire Damper
Weights
2mm 316 Stainless Steel Casings, 150mm Deep
Weights
Weights (kg) of A-60 Rectangular (Excluding Actuator) (kg) of A-60 Circular
100 200 300 400 500 600 700 800 900 1000 (Excluding Actuator)
100 4.2 5.3 6.5 7.7 8.9 10.1 11.3 12.5 13.7 14.9 100 Dia. 6.2 Compact Including Adaptor Plate 1.85kg
200 5.6 6.9 8.2 9.4 10.7 12.0 13.2 14.5 15.7 17.0 200 Dia. 10.8 Universal Including Adaptor Plate 3.00kg
300 7.2 8.6 10.0 11.4 12.8 14.2 15.6 17.0 18.4 19.8 300 Dia. 15.9 Pneumatic Including Adaptor Plate 3.00kg
400 8.3 9.8 11.3 12.8 14.2 15.7 17.2 18.7 20.1 21.6 400 Dia. 20.5 Electrical Atex Including Adaptor Plate 3.50kg
500 9.9 11.4 13.0 14.5 16.1 17.6 19.2 20.7 22.3 23.8 500 Dia. 26.0
600 11.4 13.1 14.8 16.5 18.2 19.8 21.5 23.2 24.9 26.6 600 Dia. 32.2
700 12.6 14.4 16.1 17.9 19.6 21.4 23.2 24.9 26.7 28.5 700 Dia. 37.8
800 13.8 15.6 17.4 19.3 21.1 22.9 24.8 26.6 28.4 30.3 800 Dia. 43.8
900 15.3 17.3 19.3 21.2 23.2 25.2 27.2 29.1 31.1 33.1 900 Dia. 51.1
1000 16.5 18.5 20.6 22.6 24.7 26.7 28.8 30.8 32.9 34.9 1000 Dia. 57.6
100 5.6 7.2 8.8 10.4 12.0 13.7 15.3 16.9 18.5 20.1 100 Dia. 8.5 Compact Including Adaptor Plate 1.85kg
200 7.5 9.1 10.8 12.5 14.2 15.9 17.6 19.3 20.9 22.6 200 Dia. 14.7 Universal Including Adaptor Plate 3.00kg
300 9.3 11.2 13.0 14.8 16.7 18.5 20.3 22.2 24.0 25.8 300 Dia. 21.4 Pneumatic Including Adaptor Plate 3.00kg
400 10.9 12.8 14.7 16.6 18.5 20.4 22.3 24.2 26.1 28.0 400 Dia. 27.7 Electrical Atex Including Adaptor Plate 3.50kg
500 12.8 14.8 16.8 18.8 20.7 22.7 24.7 26.6 28.6 30.6 500 Dia. 35.0
600 14.7 16.9 19.0 21.1 23.2 25.3 27.4 29.5 31.7 33.8 600 Dia. 43.1
700 16.3 18.5 20.7 22.9 25.1 27.3 29.4 31.6 33.8 36.0 700 Dia. 50.5
800 17.9 20.2 22.4 24.7 26.9 29.2 31.4 33.7 36.0 38.2 800 Dia. 58.6
900 19.8 22.2 24.6 27.0 29.4 31.8 34.2 36.6 39.0 41.4 900 Dia. 67.9
1000 21.4 23.9 26.3 28.80 31.3 33.7 36.2 38.7 41.2 43.6 1000 Dia. 76.5
100 4.8 6.1 7.5 8.9 10.2 11.6 12.9 14.3 15.7 17.0 100 Dia. 6.8 Compact Including Adaptor Plate 1.85kg
200 6.4 7.9 9.3 10.7 12.1 13.6 15.0 16.4 17.9 19.3 200 Dia. 11.7 Universal Including Adaptor Plate 3.00kg
300 8.1 9.7 11.2 12.8 14.4 15.9 17.5 19.0 20.6 22.2 300 Dia. 17.0 Pneumatic Including Adaptor Plate 3.00kg
400 9.5 11.1 12.7 14.3 16.0 17.6 19.2 20.9 22.5 24.1 400 Dia. 21.9 Electrical Atex Including Adaptor Plate 3.50kg
500 11.2 12.9 14.6 16.3 18.0 19.7 21.4 23.1 24.7 26.5 500 Dia. 27.8
600 12.9 14.7 16.5 18.4 20.2 22.0 23.9 25.7 27.5 29.4 600 Dia. 34.2
700 14.2 16.1 18.0 19.9 21.8 23.7 25.6 27.5 29.4 31.3 700 Dia. 40.0
800 15.6 17.6 19.5 21.5 23.5 25.4 27.4 29.4 31.3 33.3 800 Dia. 46.3
900 17.3 19.4 21.5 23.6 25.7 27.8 29.9 32.0 34.1 36.2 900 Dia. 53.8
1000 18.7 20.8 23.0 25.2 27.3 29.5 31.7 33.8 36.0 38.2 1000 Dia. 60.4
actionair 13
A-60 Marine Fire Damper
Weights
2mm 316 Stainless Steel Casings, 210mm Deep
Weights
Weights (kg) of A-60 Rectangular (Excluding Actuator) (kg) of A-60 Circular
100 200 300 400 500 600 700 800 900 1000 (Excluding Actuator)
100 4.8 6.2 7.6 9.0 10.4 11.7 13.1 14.5 15.9 17.3 100 Dia. 6.9 Compact Including Adaptor Plate 1.85kg
200 6.5 8.0 9.4 10.9 12.3 13.8 15.2 16.7 18.2 19.6 200 Dia. 11.9 Universal Including Adaptor Plate 3.00kg
300 8.2 9.8 11.4 13.0 14.6 16.2 17.8 19.4 21.0 22.6 300 Dia. 17.3 Pneumatic Including Adaptor Plate 3.00kg
400 9.6 11.2 12.9 14.6 16.2 17.9 19.6 21.3 22.9 24.6 400 Dia. 22.3 Electrical Atex Including Adaptor Plate 3.50kg
500 11.3 13.1 14.8 16.5 18.3 20.0 21.8 23.5 25.2 27.0 500 Dia. 28.3
600 13.0 14.9 16.8 18.7 20.6 22.4 24.3 26.2 28.1 30.0 600 Dia. 34.8
700 14.4 16.4 18.3 20.3 22.2 24.2 26.2 28.1 30.1 32.0 700 Dia. 40.7
800 15.8 17.8 19.8 21.9 23.9 25.9 28.0 30.0 32.0 34.0 800 Dia. 47.2
900 17.5 19.7 21.8 24.0 26.2 28.4 30.5 32.7 34.9 37.0 900 Dia. 55.9
1000 18.9 21.1 23.4 25.6 27.9 30.1 32.3 34.6 36.8 39.1 1000 Dia. 61.7
100 6.6 8.5 10.4 12.3 14.2 16.1 18.0 19.9 21.8 23.7 100 Dia. 9.6 Compact Including Adaptor Plate 1.85kg
200 8.8 10.7 12.7 14.7 16.7 18.6 20.6 22.6 24.6 26.5 200 Dia. 16.3 Universal Including Adaptor Plate 3.00kg
300 10.9 13.1 15.2 17.3 19.4 21.5 23.6 25.8 27.9 30.0 300 Dia. 23.5 Pneumatic Including Adaptor Plate 3.00kg
400 12.8 15.0 17.2 19.3 21.5 23.7 25.9 28.1 30.3 32.5 400 Dia. 30.4 Electrical Atex Including Adaptor Plate 3.50kg
500 15.0 17.3 19.5 21.8 24.0 26.3 28.6 30.8 33.1 35.3 500 Dia. 38.4
600 17.2 19.6 22.0 24.4 26.8 29.2 31.6 34.0 36.4 38.8 600 Dia. 47.0
700 19.1 21.5 24.0 26.5 29.0 31.4 33.9 36.4 38.9 41.3 700 Dia. 55.0
800 20.9 23.5 26.0 28.6 31.1 33.7 36.2 38.7 41.3 43.8 800 Dia. 63.6
900 23.1 25.8 28.5 31.2 33.9 36.6 39.3 41.9 44.6 47.3 900 Dia. 73.5
1000 25.0 27.7 30.5 33.3 36.0 38.8 41.6 44.3 47.1 49.8 1000 Dia. 82.7
Visual Indication
Visual indication non drive
side
Option to have drive blade visual
indication, non drive side only.
Red indicates damper closed
Green indicates damper open.
14
A-60 Marine Fire Damper
Acoustic Data
The data presented is from the Example: Damper Leakage Table 3
Laboratory Determination of Acoustic and A-60 Marine Fire Damper damper closed blade leakage.
Aerodynamic Performance of A-60 Marine Duct with a design velocity of 8 m/sec
Standard (without blade seals)
Fire Dampers. and the A-60 Marine Fire Damper RECT Optional (with blade seals)
damper blades in the fully open position.
A programme of extensive tests was 1500
carried out by an independent test facility, Pressure Drop = 22 Pa (Table 1).
approved under the NAMAS Scheme, in Multiply Velocity x Pressure Drop 1000
accordance with BRITISH STANDARDS 8 x 22 = 176.
Nos. 4196, 4773, 4856, 4857 and 4954.
From Sound Power Graph (Table 2) plot 500
From the selection of a duct velocity 176 on horizontal Velocity/Pressure axis
within the operational parameters of the against the A-60 Marine Fire Damper
Pressure Drop Vs Velocity Table 1 Velocity (m/s) X Pressure Drop (Pa) Vs Sound Power Level (dBW) Table 2
100 90
90
80
70
60 80
50
)
40 CT
DU
70 T (IN
E
30 TL
OU CT
)
RC DU
EXAMPLE LINE CI (IN
60 60 T
SOUND POWER LEVEL (dBW)
A- E
20 OU
TL
CT
T
IR C
RE
PRESSURE DROP (Pa)
EC
0
A-6
0C
0R
50
A- 6
A- 6
EXAMPLE LINE
10
9
8 40 T
7 KO
U
EA
6 T BR
EC
5 30
0R
A-6
4 T
OU
AK
RE
3 20 C B
0 CIR
A-6
2
10
1 0
1 2 3 4 5 6 7 8 9 10 15
90
900
9000
10
20
30
40
50
60
70
80
100
200
300
400
500
600
700
800
1000
2000
3000
4000
5000
6000
7000
8000
10000
actionair 15
A-60 Marine Fire Damper
Series
A-60 RECT(Galv) A-60 CIRC (Galv) A-60 RECT (316) A-60 CIRC (316)
A-60 Marine Fire Damper. A-60 Marine Fire Damper. A-60 Marine Fire Damper. A-60 Marine Fire Damper.
430 Ferritic Stainless Steel 430 Ferritic Stainless Steel 316 Austenitic Stainless Steel 316 Austenitic Stainless Steel
Blades. Blades. Blades. Blades.
Square or Rectangular Flanges. Circular Flanged. Square or Rectangular Flanges. Circular Flanged.
Galvanised 150mm deep Casing Galvanised 230mm deep 316 Stainless Steel 150mm deep 316 Stainless Steel 230mm deep
Standard Casing. Casing. Standard Casing.
1.2mm, 2mm or 3mm Casing.
(210mm deep Casing available 1.2mm, 2mm or 3mm Casing. 1.2mm, 2mm or 3mm Casing. 1.2mm, 2mm or 3mm Casing.
in 2mm and 3mm options). (290mm deep Casing available (210mm deep Casing available (290mm deep Casing available
in 2mm and 3mm options). in 2mm and 3mm options). in 2mm and 3mm options).
Electric Control Mode 5 24V AC or DC. Standard (without blade seals). Standard (With holes).
Electric Control Mode 6 230V AC 50/60Hz. Optional (with blade seals). Optional (No flange holes).
Electric Control Mode 120 120V AC 50/60Hz. Visual Indication - Non drive side Optional (Customer own pattern).
Standard (without)
Pneumatic 5 - 8 Bar Air Supply. Optional (with). Casing Depth
Standard (150mm)
Electrical Atex Universal 24V - 230V Casing Thickness 1.2, 2 or 3mm Optional (210mm in 2mm or 3mm
AC/DC 50/60Hz. Standard (1.2mm) case thickness only).
Optional (2mm or 3mm).
Example
Quantity Series Thickness Depth Duct size Control Modes Seals Flange Holes Accessories
3 A-60 RECT (Galv) 1.2mm 150mm 400 (W) x 250 (H) M5 Standard Customer DRIM
16
A-60 Marine Fire Damper
Features
Optimum blades pitch minimises the penetration of
wind-driven rain, reducing damage and additional
operating expenses.
Cd figure of 0.39.
Options
Sub cill if required.
Glazing channels.
Finishes
Mill.
80mm 50mm
actionair 17
A-60 Marine Fire Damper
Standard Construction
Frame
51mm Deep 6063T6 extruded aluminium with a 1.5mm
nominal wall thickness. Jamb Section
50.8
Blades
6063T6 extruded aluminium with 1.1mm nominal wall
thickness. Double drainable blades are sight proof.
Finishes
25.4
23.32
Polyester powder - coated to BS6496.
Minimum Size
150mm x 150mm.
38.1
supports that increase overall louvre depth. Louvres in
excess of max factory assembly size will require
19.1
Blade Section
18
A-60 Marine Fire Damper
Core Airflow Free Area Effectiveness Class Core Airflow Free Area Effectiveness Class
Velocity m3/min Velocity Ratio Velocity m3/min Velocity Ratio
m/s m/sec m/s m/sec
0 0 0 99.9 A 0 0 0 99.9 A
0.7 40.2 2.0 99.9 A 0.6 34.8 1.5 99.8 A
1.0 60.0 2.6 99.9 A 0.9 56.7 2.4 99.4 A
1.4 86.9 3.7 99.9 A 1.5 90.1 3.8 99.3 A
1.9 114.1 4.9 99.9 A 2.0 121.3 5.2 97.8 B
2.4 143.8 6.1 99.3 A 2.5 150.5 6.4 96.2 B
3.0 177.7 7.6 97.1 B 2.9 173.1 7.4 95.4 B
3.5 208.8 8.9 96.1 B 3.5 210.7 9.0 90.9 C
Notes:
1. Core area is the open area of the louvre face (face area less Pressure Drop
louvre frames). Cores velocity is the airflow velocity through the
core area of the louvre (1m x 1m). Pressure Drop testing performed on
1219 x 121mm unit.
2. Free area of test size is calculated per AMCA standard 500-L.
3. Wind Driven Rain Penetration Classes:
248.9 1.00
Class Effectiveness 224.01 .90
199.12 .80
A 1 to .99 174.23 .70
74.67 .30
INTAKE
4. Intake Discharge Loss Class 2
EXHAUST
Discharge Loss Coefficient is calculated by dividing a louvers 49.78 .20
1524
1829
2134
2438
2743
3048
122
152
183
213
244
274
305
610
924
30
61
91
actionair 19
WORLDWIDE A60 FIRE DAMPER CUSTOMERS
actionair