Вы находитесь на странице: 1из 3

SUB: RCC AND STEEL MODULE-38C

MODULE-38C
Analysis and design of tension and compression members.
____________________________________________________________________________________________________________

1. ISA 100 100 10 mm (Cross sectional area = 1908) serves as tensile


member. This angle is welded to a gusset plate along A and B
appropriately as shown. Assuming the yield strength of the steel to be
260 N/ the tensile strength of this member can be taken to be
approximately,

(A) 500 kN (B) 300 kN

(C) 225 kN (D) 375 kN

Ans:

2. In the design of lacing system for a built-up steel column, the maximum
allowable slenderness ratio of a lacing bar is

(a) 120 (b) 145


(c) 180 (d) 250

Ans: (b)

JH ACADEMY Page 1
SUB: RCC AND STEEL
MODULE-38C
3. Which of the following elements of a pitched roof industrial steel
building primarily resists lateral load parallel to the ridge?

(a) Bracings (b) Purlins


(c) Truss (d) Columns

Ans: (b)

4. A truss tie consisting of 2 ISA 75 x 75 x 8 mm carries a pull of 150 kN.


At ends the two angles are connected, one each on either side of a
10mm thick gusset plate, by 18 mm diameter rivets arranged in one
row. The allowable stresses in rivet are fs=90.0 N/mm2 and fbr=250
N/mm2.

Maximum tensile stress in the tie in N/mm2 is


(a) 93.6 (b) 87.5
(c) 77.2 (d) 66.0

Ans:
( )
( )
( ) ( )

5. A truss tie consisting of 2 ISA 75 x 75 x 8 mm carries a pull of 150 KN.


At ends the two angles are connected, one each on either side of a
10mm thick gusset plate, by 18 mm diameter rivets arranged in one
row. The allowable stresses in rivet are fs=90.0 N/mm2 and fbr=250
N/mm2
Minimum number of rivets required at each end is

(a) 2 (b) 3
(c) 4 (d) 5

Ans:

6. A strut in a steel truss is composed of two equal angles ISA 150


mm x 150 mm of thickness 100 mm connected back-to-back to the
same side of a gusset plate. The cross sectional area of each angle is
2921 mm2 and moment of inertia (Ixx = Iyy) is 6335000 mm4. The
distance of the centroid of the angle from its surface (Cx =Cy) is 40.8
mm. The minimum radius of gyration of the strut is

(a) 93.2 mm (b) 62.7 mm


(c) 46.6 mm (d) 29.8 mm

Ans:

JH ACADEMY Page 2
SUB: RCC AND STEEL
MODULE-38C
7. Two equal angles ISA 100 mm x 100 mm of thickness 10 mm are
placed back-to-back and connected to the either side of a gusset plate
through a single row of 16 mm diameter rivets in double shear. The
effective areas of the connected and unconnected legs of each of these
angles are 775 mm2 and 950 mm2, respectively. If these angles are NOT
tack riveted, the net effective area of this pair of angles is

(a) 3650 mm2 (b) 3450 mm2


(c) 3076 mm2 (d) 2899 mm2

Ans:

( )

JH ACADEMY Page 3

Вам также может понравиться