Академический Документы
Профессиональный Документы
Культура Документы
Dynamic shear modulus 0.47 N/mm2 DIN ISO 1827* at static load limit
Mechanical loss factor 0.08 DIN 53513* depending on frequency, load and amplitude (reference value)
Further characteristic values on request All information and data is based on our current knowledge. The data can be applied for calculations and as
guidelines, are subject to typical manufacturing tolerances, and are not guaranteed.
* Tests according to respective standards We reserve the right to amend the data.
** At form factor q=3
Further information can be found in VDI Guidline 2062 Page 2.
www.getzner.com
1
Sylodyn ND
0.4
Static
load limit
0.2
0
0 1 2 3 4 5 6 7 8 9 10 11 12
Delection [mm]
0.8
12.5 mm 25 mm
37.5 mm
0.6
0.4
Static
load limit
0.2
0
0 1 2 3 4 5 6 7 8 9 10 11 12
Delection [mm]
12.5 mm 25 mm
0.6
37.5 mm
Operating load range
50 mm
0.4
Static
load limit
0.2
0
0 1 2 3 4 5 6 7 8 9 10 11 12
Delection [mm]
2
Modulus of elasticity Natural frequency
4 10 Hz
0.4
50 mm
2
37.5 mm
Static
0.2
25 mm
12.5 mm
0 0
0 0.2 0.4 0.6 0.8 0 5 10 15 20 25
Speciic load [N/mm2] Natural frequency [Hz]
0.6
30 Hz
4
10 Hz
0.4
50 mm
2
37.5 mm
Static 0.2
25 mm
12.5 mm
0 0
0 0.2 0.4 0.6 0.8 0 5 10 15 20 25
Speciic load [N/mm2] Natural frequency [Hz]
0.6
4 30 Hz
10 Hz
0.4
2 50 mm
0.2 37.5 mm
Static
25 mm
12.5 mm
0 0
0 0.2 0.4 0.6 0.8 0 5 10 15 20 25
Speciic load [N/mm2] Natural frequency [Hz]
Static modulus of elasticity as a tangent modulus taken from the load Natural frequency of a single-degree-of-freedom system (SDOF system)
delection curve; dynamic modulus of elasticity due to sinusoidal excitation consisting of a ixed mass and an elastic bearing consisting of Sylodyn ND
with a velocity level of 100 dBv re. 510-8 m/s; test according to DIN 53513 based on a stiff subgrade; parameter: thickness of elastomeric bearing
3
Vibration isolation eficiency
200
Disturbing frequency [Hz]
180
-40 dB/99 % Reduction of the transmitted
-30 dB/97 % mechanical vibrations by implemen-
160
tation of an elastic bearing
140
consisting of Sylodyn ND
-20 dB/90 %
120 Parameter: factor of transmission in
100 dB, isolation rate in %
80 -10 dB/69 %
60
-0 dB/0 %
40
20
0
5 10 15 20 25 30 35 40 45 50
Natural frequency [Hz]
Creep behaviour
Relative deflection [% of thickness with unstressed sample]
25
Increase in deformation under
consistent loading
20
Parameter: permanent loading
100 % load
Form factor: q=3
15
10
50 % load
1d 1m 1a 10 a
0
0.1 1 10 100 1,000 10,000 100,000 1,000,000
Period of loading [h]
6
Change of dynamic modulus of
5 100,000 h elasticity under consistent loading
1,000 h (at 10 Hz)
4 Parameter: load duration
Form factor: q=3
10 h
3
0.1 h
0
0 0.4 0.8
Permanent loading [N/mm2]
www.getzner.com
4
Temperature dependency
Dyn. E-modulus [N/mm2]
0.2
2 30 Hz
0.1 10 Hz
1
0 0
-10 0 10 20 30 40 50 -10 0 10 20 30 40 50
Temperature [C] Temperature [C]
Frequency dependency
0.5
Mechanical loss factor
Dyn. E-modulus [N/mm2]
5 DMA-tests; mastercurve
with a reference-tempera-
ture of 21 C;
tests within the linear area
4 0.4 of the load delection curve,
at low speciic loads
3 0.3
2 0.2
1 0.1
0 0
1 10 100 1,000 1 10 100 1,000
Frequency [Hz] Frequency [Hz]
6
Dependency on amplitude:
preload at static load limit;
Form factor: q=3, thickness
of material 25 mm
0.6 0.035 N/mm2/s
Dependency on loading
30 Hz
velocity:
4 0.35 N/mm2/s Form factor: q=3, thickness
of material 25 mm
10 Hz 3.5 N/mm2/s
0.4
0.2
0 0
0.01 0.10 1.00 0 1 2 3 4 5 6 7 8 9 10 11 12
Amplitude [mm] Delection [mm]
www.getzner.com
5
Form factor
The form factor is a geometric measure for the shape of Loaded area
an elastomeric bearing deined as the ratio of the loaded
area and the area of sum of the perimeter surfaces.
Loaded area
Deinition: Form factor =
Perimeter surface area
Perimeter
surface area
Iw
For a rectangular shape: q =
2t(I+w)
(l..length, w..width, t..thickness)
Perimeter surface area
Inluence of the form factor on the delection at the Inluence of the form factor on the static load limit
static load limit for a homogeneous material for a homogeneous material
Reference value: Form factor q=3 Reference value: Form factor q=3
Deviation of delection [%]
50 % 0.4
40 %
Increase of Increase of
30 %
delection static load limit
0.3
20 %
DB SN ND en Copyright by Getzner Werkstoffe GmbH l 09-2014
Decrease of
10 % static load limit
0.2
0%
Decrease
of delection
-10 %
We reserve the right to amend the data.
-20 % 0.1
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Form factor Form factor
AUSTRIA Brs GERMANY Berlin Munich FRANCE Lyon JORDAN Amman JAPAN Tokyo
INDIA Pune CHINA Beijing USA Charlotte www.getzner.com
6