Академический Документы
Профессиональный Документы
Культура Документы
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
aa
re
kh.
co
m
TOS/SOM www.aarekh.com
1. A beam fixed at both ends carries a uniformly distributed load on entire length. The ratio of bending moment at the support to
the bending moment at mid span is given by [SSC JE - 2013]
(a) 0.5
(b) 1.0
(c) 0.5
(d) 2.0
2. From a circular plate of diameter 6.0 cm. a circle is cut out whose diameter is a radius of the plate. The distance of centre of
gravity of the remainder from the centre of circular plate is [SSC JE - 2013]
(a) 2.0
(b) 1.5
(c) 1.0
(d) 0.5
m
3. In a section undergoing pure bending, the neutral surface is subjected to [SSC JE - 2013]
(a) compression strain
(b) tensile strain
(c) zero strain
(d) none of the above
co
4. Of the several prismatic beams of equal lengths and of same material, the beam that can carry maximum load in flexure is the
one having maximum [SSC JE - 2013]
(a) Depth of section
(b) Area of cross section
(c) Section modulus
h.
(d) Moment of inertia
5. A structure which offers negligible or zero resistance on bending at any point is known as [SSC JE - 2013]
(a) Beam
(b) Girder
k
(c) Lintel
(d) Cable
re
6. Moment of inertia of rectangular section shown in fig. about its horizontal centroidal axis is [SSC JE - 2014]
b
d
aa
(a) db3/12
(b) db3/3
(c) bd3/12
(d) bd3/3
7. If 'A' is the area of cross-section and ' I ' is moment of inertia of a given plane section, then radius of gyration (r) the is given
by the formula [SSC JE - 2014]
(a) r = I / A
(b) r = I / A
(c) r = A / I
(d) r = A / I
8. A 40 cm. diameter circular timber column is 4 m. long. The slenderness ratio of the column is: [SSC JE - 2014]
(a) 20 2
(b) 10
(c) 20
(d) 40
TOS/SOM www.aarekh.com
9. A simply supported beam of span 'L' is loaded with downward UDL of intensity W/m over its entire length. Which of the
following orientation of T-beams is preferred to a resist bending ? [SSC JE - 2014]
(a) (b)
(c) (d)
10. Section modulus for a rectangular section is given as: [SSC JE - 2010]
(a) bd2/36
(b) bd3/36
m
(c) bd2/6
(d) bd2/12
co
(b) rigidity
(c) curvature
(d) shear force
13. The shear stress distribution over a beam of solid circular section is such that : [SSC JE - 2010]
k
(a) qmax = 2qmean
(b) qmax = 1.5 qmean
(c) qmax = 1.33 qmean
re
(c) MZ / y
(d) MI / y
16. Shear stress at y distance above neutral axis (NA) on a prismatic beam due to shear force V is given by [SSC JE - 2012]
(a) VAyb/I
(b) Vb/(AyI)
(c) VAy/(Ib)
(d) VI/(bAy)
m
17. For a given shear force across a symmetrical ' I ' section the intensity of shear stress is maximum at the [SSC JE - 2012]
(a) extreme fibres
(b) centroid of the section
(c) at the junction of the flange and the web, but on the web
co
(d) at the junction of the flange and the web, but on the flange
18. For the given stress, the ratio of moment of resistance of a beam of square cress-section when placed with its two sides
horizontal to the moment of resistance with its diagonal horizontal is given by [SSC JE - 2012]
(a) 1/2
(b) 1
h.
(c) 1/2
(d) 2
19. A bar, L meter long and having its area of cross-section A, is subjected to gradually applied tensile load W. The strain energy
stored in the bar is given by [SSC JE - 2012]
k
(a) WL/(2AE)
(b) WL/(AE)
(c) W2L/(AE)
re
(d) W2L/(2AE)
20. In a beam at a section carrying a shear force F, the shear stress is maximum at [SSC JE - 2012]
(a) Neutral surface
(b) Top most fibre
aa
21. For a beam carrying a uniformly distributed load, the strain energy will be maximum in case the beam is [SSC JE - 2012]
(a) Cantilever
(b) Simply supported
(c) Propped cantilever
(d) Fixed at both ends
22. The cross-section of a joist is a T-section, 120 mm X 200 mm X 12 mm and horizontal side is 120 mm. Sketch the shear stress
distribution for the given section and also find maximum shear stress if it has to resist a 200 kN shear force.
23. Determine the centroid and shape factor of a I section which is symmetrical about vertical axis, top flange being 5 cm X 5 cm,
bottom flange 20 cm X 2 cm and web 2 cm X 10 cm.
24. An R.S.J. 55 cm deep and 19 cm wide having flange and web thickness of 1.5 cm and 0.989 cm respectively is used as a beam.
Calculate the moment of resistance at a section where maximum stress is 100 N/mm2 .
TOS/SOM www.aarekh.com
Answers :- 1. (d), 2. (d), 3. (c), 4. (c), 5. (d), 6. (c), 7. (b), 8. (b) 9. (b), 10. (c), 11. (c), 12. (d), 13. (c), 14. (b), 15. (c), 16.
(c), 17. (b), 18. (d), 19. (d), 20. (a), 21. (a)
m
co
k h.
re
aa