Академический Документы
Профессиональный Документы
Культура Документы
(568234)
Owners manual
PX-6
Professional monitor system
Thank you very much for purchasing the Fostex PX-6 professional monitor system.
This manual provides the operating instructions for the PX-6. Read this before you use the unit for the
first time. After reading, keep this manual in a convenient place so that you can consult it at any time.
WARNINGS and PRECAUTIONS
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF ATTENTION: Danger dexplosion si les piles sont remplaces de faon
PLUG TO WIDE SLOT, FULLY INSERT. incorrect. Remplacer les piles seulement par le mme type de pile ou
ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQUES, APAR DE LA lquivalent.
FENTE LARGE, FOND. WARNING: Do not install this equipment in a confined space such as a book
case or similar unit.
WARNING: To reduce the risk of fire or electric shock, do not expose this AVIS: Ne pas installer cet quipement dans un espace confin comme une
apparatus to rain or moisture. bibliothque ou une unit similaire.
AVIS: Pour rduire le risque dincendie ou de choc lectrique, ne pas ex-
poser cet appareil sous la pluie et lhumidit. WARNING: Mains plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the apparatus
CAUTION: Use of any controls or adjustments or performance of proce- from the mains completely, the mains plug should be disconnected from the
dures other than those herein specified may result in hazardous radiation mains socket outlet completely.
exposure. AVIS: La prise du secteur est utilis pour dconnecter le systme. La prise
ATTENTION: Lutilisation de tout contrle ou de rglages ou de procdures du secteur ne doit pas tre obstrue ou doit tre facilement accessible pen-
autres que celles indiques ci-aprs peut entraner une exposition des ra- dant son utilisation. Pour tre compltement dconnect de lalimentation
diations dangereuses. dentre, la prise doit tre dbranche du secteur.
WARNING: Changes or modifications to this unit not expressly approved WARNING: TO REDUCE THE RISK OF
ATTENTION ELECTRIC SHOCK, DO NOT REMOVE
by the party responsible for compliance could void the users authority to RISQUE D LECTROCUTION COVER (OR BACK). NO USER SERVICE-
operate the equipment. NES PAS OUVRIR
ABLE PARTS INSIDE. REFER SERVICING
AVIS: Les changements ou modifications cette unit ntant pas expres- TO QUALIFIED SERVICE PERSONNEL.
sment approuv par la partie responsable de la conformit pourrait annuler
lautorit de lutilisateur de faire fonctionner lquipement. AVERTISSEMENT: POUR RDUIRE LE
CAUTION RISQUE DE CHOC LECTRIQUE, NE PAS
WARNING: Do not place the unit on top of any soft, porous, or sensitive RISK OF ELECTRIC SHOCK ENLEVER LE COUVERCLE (NI LE DOS).
DO NOT OPEN
surfaces to avoid damaging the surface. Use a protective barrier between AUCUNE PICE LINTRIEUR. EN-
TRETIEN DE PERSONNEL QUALIFIE.
the unit and surface to protect the surface.
AVIS: Ne placez pas lappareil au-dessus de toutes les surfaces souples,
poreux, ou sensibles pour viter dendommager la surface. Utilisez une bar- The lightning flash with arrowhead symbol, within an equilateral trian-
gle, is intended to alert the user to the presence of uninsulated dan-
rire de protection entre lunit et la surface protger la surface.
gerous voltage within the products enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
WARNING: Use of this unit near fluorescent lighting may cause interference Le symbole de lclair flch dans un triangle quilatral, est destin
regarding use of the remote. If the unit is displaying erratic behavior move alerter lutilisateur de la prsence dune tension dangereuse dans le
away from any fluorescent lighting, as it may be the cause. botier du produit qui peuvent tre des ampleur suffisante pour con-
AVIS: Lutilisation de cet appareil proximit dclairage fluorescent peut stituer un risque dlectrocution aux personnes.
provoquer des interfrences sur lutilisation de la tlcommande. Si lappareil
The exclamation point within an equilateral triangle is intended to alert
affiche un comportement erratique sloigner de tout clairage fluorescent,
the user to the presence of important operating and maintenance (ser-
telle quelle peut tre la cause. vicing) instructions in the literature accompanying the appliance.
Le point dexclamation lintrieur dun triangle quilatral est destin
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace attirer lattention de lutilisateur sur la prsence dinstructions impor-
only with the same or equivalent type. tantes sur lemploi ou de la maintenance (rparation) de lappareil dans
la documentation fournie.
E-2
Table of contents Introduction
WARNINGS and PRECAUTIONS. . . . . . . . . . . . E-2 The PX-6 is a powered monitor speaker system
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . E-2 that can connect to a professional or consumer
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . E-3 audio device.
FCC (U.S.A.) & ICES-003 (Canada)
INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . E-3 A rotary encoder is used for adjusting the audio
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3 volume level as well as tone (bass and treble)
Supplied accessories. . . . . . . . . . . . . . . . . . . . . E-3 controls, achieving precise digital processing.
Features and functions . . . . . . . . . . . . . . . . . . . E-4 By using a linear phase filter for the network
Volume level and tone controls. . . . . . . . . . . . . E-6 system, phase interference is minimized, result-
Adjusting volume level. . . . . . . . . . . . . . . . . . . E-6 ing natural sound that is comparable to a full-
Adjusting the tone controls. . . . . . . . . . . . . . . . E-7 range speaker.
Standby function . . . . . . . . . . . . . . . . . . . . . . . . E-8 Precise level adjustment in 440 steps is pos-
Auto standby function . . . . . . . . . . . . . . . . . . E-8 sible.
Entering the standby mode manually. . . . . . . E-8 You can adjust the treble by changing the
Releasing the standby mode manually. . . . . . E-8 tweeter level within the +/- 3 dB range.
Parameter lock function . . . . . . . . . . . . . . . . . . E-8 You can change the low roll-off frequency. The
Using the unit with a subwoofer . . . . . . . . . . . . E-9 subsonic filter that associates with the roll-off
Preparing a subwoofer . . . . . . . . . . . . . . . . . . E-9 frequency eliminates unnecessary ultra-low fre-
Enabling the high-pass filter. . . . . . . . . . . . . . E-9 quency range.
Adjusting the phase of the high-pass filter. . . E-9 An 85 Hz high-pass filter with 36 dB/oct. slope
Subwoofer settings after adjusting is provided, so you can use the PX-6 with a
the phase of the high-pass filter. . . E-11 subwoofer.
Disabling the high-pass filter. . . . . . . . . . . . . E-11 When using the PX-6 with a subwoofer, you
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . E-11 can adjust the phase within the range between
Speaker section. . . . . . . . . . . . . . . . . . . . . . . E-11 0 degree and 180 degrees (9 degree step) de-
Amplifier section. . . . . . . . . . . . . . . . . . . . . . E-11 pending on the subwoofer position.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-11 When you turn on the power, the fade-in func-
Declaration of EC Directive. . . . . . . . . . . . . . . E-12 tion is automatically activated and the volume
Fostex distributors list in Europe. . . . . . . . . . . E-12 level gradually increases to the previously
stored level.
FCC (U.S.A.) & ICES-003 (Canada) The parameter lock function prevents the set-
tings from being changed inadvertently.
INFORMATION High power 6.5-inch woofer featuring the dia-
1. IMPORTANT NOTICE phragm that contains aramid fiber for reinforce-
This product, when installed as indicated in the instructions contained in this
manual, meets FCC and ICES-003 requirements. Changes or modifications ment.
not expressly approved by Fostex Company for compliance could void the 1-inch soft dome tweeter featuring UFLC dia-
users authority to operate the equipment. DO NOT MODIFY THIS PRODUCT.
phragm for stable high-mid range sound.
2. IMPORTANT Rigid cabinet design eliminates unwanted vibra-
In order to comply with FCC and ICES-003 requirements, use high quality
shielded cables for connection to accessories and / or another products. If
tion.
any cables are supplied with this product, they MUST be used. Follow all in- Standby mode saves electricity.
stallation instructions. Failure to do so could void your FCC / ICES-003 autho- Three types of input connectors are provided
rization to use this product in the USA / Canada.
for input; XLR, phone and RCA.
3. NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installa- Supplied accessories
tion. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to correct the interference by one or more of the following
measures: The following accessories are supplied with the
Reorient or relocate the receiving antenna. PX-6.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. Power cord x 1
Consult the dealer or an experienced radio/TV technician for help. Owners manual (this manual) x 1
4. Compliance with Part 15 of FCC Rules and Canadian ICES-003.
This device complies with Part 15 of the FCC Rules. Operation is subject to
After purchasing the PX-6, check that all the
the following two conditions: (1) This device may not cause harmful interfer- above items are included in the package.
ence, and (2) this device must accept any interference received, including
interference that many cause undesired operation.
E-3
Features and functions
[INPUT] jack (RCA jack)
You can connect an RCA plug to this unbalanced
line input jack.
<Note>: You cannot use both the RCA and combo
[INPUT] jacks simultaneously.
When a plug is plugged into the RCA jack, the phone
VOLUME jack is disabled.
When an RCA plug and an XLR connector are simul-
taneously inserted to the RCA and XLR jacks respec-
TRIM
[CONTROL] knob
Used for controlling the volume level and the tone
(bass and treble).
By pressing this knob, you can change the con-
trolling item in the current mode (LEVEL or TONE
mode) selected by the mode select switch.
By rotating this knob, you can adjust the value of
the currently selected item.
By pressing and holding down this knob for a few
seconds, the settings of all items are saved to the
unit.
See Level and tone controls on pages 6-7 for
details.
This knob is also used when you make high-pass
filter settings for using the unit with a subwoofer.
See Using the unit with a subwoofer on pages
9-11 for details.
E-4
Features and functions
Mode select switch
You can select the control mode: LEVEL or TONE.
When the switch is set to LEVEL, you can control
the volume level using the [CONTROL] knob.
When the switch is set to TONE, you can control
the bass and treble using the [CONTROL] knob.
When the switch is set to the center position (OFF),
you cannot change any value using the [CON-
VOLUME
TROL] knob.
TRIM
details.
[POWER] button
Turns on or off the power.
[AC IN] connector
Connects to the supplied power cord.
Status indicators
When the VOLUME item is selected in the LEVEL
mode or the TREBLE item is selected in the
TONE mode, the upper indicator lights or flashes.
When the TRIM item is selected in the LEVEL
mode or the BASS item is selected in the TONE
mode, the lower indicator lights or flashes.
If the current values of all items match the stored
values, the indicator lights steadily.
If you change any of the stored values, the indi-
cator flashes.
See Level and tone controls on pages 6-7 for
details.
For the details about how the indicator acts when
the unit is used with a subwoofer and the high-
pass filter is active, see Using the unit with a
subwoofer on page 9-11.
E-5
Volume level and tone controls
You can adjust volume level as well as tone using 1) Set the mode select switch to the LEVEL posi-
the [CONTROL] knob. tion.
LEVEL
VOLUME
2) Adjust the volume level coarsely by rotating the
[CONTROL] knob.
TRIM <Note>: If you change the stored value by rotating
the [CONTROL] knob, the status indicator changes
from lighting to flashing .
LEVEL
If necessary, fine-tune the volume level by follow-
ing steps 3) and 4) below.
E-6
Volume level and tone controls
1) Set the mode select switch to the TONE posi-
tion.
LEVEL
VOLUME
2) Adjust the treble by rotating the [CONTROL]
knob.
TRIM
<Note>: You can adjust the treble by changing the
tweeter level within the range of -3 dB to +3 dB.
E-7
Standby function Parameter lock function
Auto standby function When the mode select switch is set to OFF, the
parameter lock function is enabled and the unit is
When the mode select switch is set to VOLUME in the following conditions.
or TONE, the auto standby function is enabled. You cannot change the setting values.
When the auto standby function is enabled, if The auto standby function is disabled.
there is no input signal for four hours, the unit au-
tomatically enters the standby mode.
E-8
Using the unit with a subwoofer
The unit is equipped with a phase-adjustable
high-pass filter so you can use the unit with a Adjusting the phase of the
subwoofer in the optimum condition. The high- high-pass filter
pass filter cutoff frequency is fixed to 85 Hz with
a slope of 36 dB/oct. By adjusting the phase of 1) When the unit is in the condition after step 3)
the unit between 0 degree and 180 degrees in 20 above, rotate the [CONTROL] knob to adjust
steps, you can match the phase between a sub- the phase of the high-pass filter.
woofer and the unit, which ensures to get natural
and smooth crossover characteristics regardless Ideally, a subwoofer and the PX-6 should be po-
of the subwoofers position. sitioned at the same distance from the listening
point. In this case, you do not need to adjust the
<Note>: When the high-pass filter is enabled, the phase for compensation (phase adjustment: 0
tone control setting for BASS is disabled. degree).
LEVEL
LS RS
E-9
Using the unit with a subwoofer
When a subwoofer and the PX-6 are not posi-
tioned at the same distance from the listening 10 11
point, you need to adjust the phase to compen- 8 9 12
Level indicator scale 7 13
sate. 6 14
5 15
4 16
3 17
Sub
2 18
C
L
1 19
R L 0 20
R
1m 1m
E-10
Using the unit with a subwoofer Specifications
Subwoofer settings after adjusting Speaker section
the phase of the high-pass filter Enclosure type: 2 way bass reflex
Units:
Input an 85-Hz sine wave to both the unit and Tweeter: 1-inch soft dome tweeter
the subwoofer. If you find the phase is re- Woofer: 6.5-inch, Aramid fiber diaphragm
versed, flip the phase of the subwoofer 180 Frequency response: 48 Hz 20 kHz
degrees.
E-11
Declaration of EC Directive
This equipment is compatible with the EMC Directive (2004/108/EC) - Directive on approximation of member nation's ordinance concerning
the electromagnetic compatibility and with the Low Voltage Directive (73/23/EEC) - Directive on approximation of member nation's
ordinance concerning electric equipment designed to be used within the specified voltage range.
<AUSTRIA> <ITALY>
NAME: Mega Audio GmbH NAME: Proel S. p. A.
ADD: Stromberger Str. 32, D-55411 Bingen, Germany ADD: Zona Via Alla Ruenia, 37/43 64027 - SantOmero (Teramo),
TEL: (+49) 6721-94330, FAX: (+49) 6721-32046 Italy
TEL: (+39) 0861-81241, FAX: (+39) 0861-887862
<CZECHO>
NAME: Praha Music Center spol s.r.o. <THE NETHERLANDS>
ADD: Ocelarska 937/39, Praha 9, 190 00, Czecho NAME: IEMKE ROOS AUDIO B. V.
TEL: (+420) 226-011-111, FAX: (+420) 226-011-112 ADD: Kuiperbergweg 20, 1101 AG Amsterdam, The Netherlands
TEL: (+31) 20-697-2121, FAX: (+31) 20-697-4201
<DENMARK>
NAME: Benum Nordic A/S <NORWAY>
ADD: Meterbuen 18, Skovlunde, 2740 Denmark NAME: Siv. Ing. Benum AS
TEL: (+45) 4451-8900, FAX: (+45) 4451-8911 ADD: P. O. Box 145, Vinderen, 0319 Oslo, Norway
TEL: (+47) 2213 9900, FAX: (+47) 2214 8259
<FINLAND>
NAME: Noretron Oy Audio <POLAND>
ADD: P. O. Box 22, FIN-02631 Espoo, Finland NAME: Mega Music Spolka z o.o
TEL: (+358) 9-5259330, FAX: (+358) 9-52593352 ADD: Ul. Lesna 15, 81-876 Sopot, Poland
TEL: (+48) 58-551-18-82, FAX: (+48) 58-551-18-72
<FRANCE>
NAME: Sennheiser France <SPAIN>
ADD: 128 bis, avenue Jean-Jaures, 94851 Ivry-sur-Seine Cedex, NAME: Letusa S. A.
France ADD: C/Laguna 10, 28923 Alcorcon, Madrid, Spain
TEL: (+33) 1 4987 0300, FAX: (+33) 1 4987 0324 TEL: (+34) 91-4862800, 91-4470898, FAX: (+34) 91-6414597
<GERMANY> <SWEDEN>
NAME: Mega Audio GmbH NAME: Benum Nordic A/S
ADD: Stromberger Str. 32, D-55411 Bingen, Germany ADD: Aldermansvagen 17, 171 48 Solna, Sweden
TEL: (+49) 6721-94330, FAX: (+49) 6721-32046 TEL: (+46) 8 207710
<GREECE> <SWITZERLAND>
NAME: Bon Studio S. A. NAME: Audio Bauer Pro AG
ADD: 6 Zaimi Street, Exarchia, 106.83 Athens, Greece ADD: Bernerstrasse-Nord 182, CH-8064 Zurich, Switzerland
TEL: (+30) 210-3809-605, 606, 607, 608 TEL: (+41) 1-4323230, FAX: (+41) 1-4326558
FAX: (+30) 210-3845-755, 210-3827-868
<UK>
NAME: SCV London
ADD: 40 Chigwell Lane, Oakwood Hill Industrial Estate, Loughton,
Essex IG10 3NY U. K.
TEL: (+44) 20-8418-0778, FAX: (+44) 20-8418-0624
FOSTEX CO.
1-1-109, Tsutsujigaoka, Akishima City, Tokyo, 196-8550, Japan