Академический Документы
Профессиональный Документы
Культура Документы
All other
objects on each Numbers sheet were placed on separate worksheets. Please be aware that formula
calculations may differ in Excel.
Export Summary 2
Cover Page
Summary HVAC
HVAC BOQ(LEVEL-1 TO 6
Electrical Estimate
BMS BOQ
This document was exported from Numbers. Each table was converted to an Excel worksheet. All other
objects on each Numbers sheet were placed on separate worksheets. Please be aware that formula
calculations may differ in Excel.
Cover Page
Table 1 Cover Page
Summary HVAC
Table 1 Summary HVAC
HVAC BOQ(LEVEL-1 TO 6
Table 1 HVAC BOQ(LEVEL-1 TO 6
HVAC BOQ LEVEL-7 TO 10
Table 1 HVAC BOQ LEVEL-7 TO 10
Electrical Estimate
Table 1 Electrical Estimate
All Drawings from the Sheet Electrical Estimate - Drawings
BMS BOQ
Table 1 BMS BOQ
3
PROJECT
MEP ESTIMATE
FOR
BUILDING SERVICES
Dated: 06 -10-2017
4
5
ESTIMATE FOR HVAC WORK
S.No
1)
2)
3)
4)
5)
1)
2)
3)
6
ESTIMATE FOR HVAC WORK
7
ESTIMATE FOR HVAC WORK
8
ESTIMATE FOR HVAC WORK
Part I Equipment.
INDEGENIOUS ITEMS
ELECTRICAL
TOTAL(HVAC)
9
ESTIMATE FOR HVAC WORK
10
ESTIMATE FOR HVAC WORK
11
ESTIMATE FOR HVAC WORK
PITAL
Amount
INR
INR
INR
INR
INR
INR
INR
INR
INR
INR
12
ESTIMATE FOR HVAC WORK
13
ESTIMATE FOR HVAC WORK
14
ESTIMATE FOR HVAC WORK
SUMMARY OF PRICES
TOTAL(HVAC)
Part I Equipment.
15
ESTIMATE FOR HVAC WORK
Refrigerant 134a
SUMMER OPERATION
Cooling Capacity : 300 TR Actual Cooling Capacity
Desuperheater Capacity @ 45 Deg C : 220 KW
Air entering in condenser : 32 Deg C
Chilled water 'In' : 53.6F
Chilled water 'Out' : 44.6F
Chiller Fouling Factor (FPS) : 0.0001
Minimum EER : 3.55 ( at Above conditions)
1a) The price quoted for supply, installation, testing & commissioning of NO 2
imported Air Cooled Chilling Unit shall be inclusive of all duties & taxes,
insurance, transportation / shipment cost from works to site, loading /
unloading, port clearance charges etc. as required in Indian Rupees.
Part I Equipment.
Make:-Xylem/Grudfoss/
Capacity of Each Pump GPM 720
Pump Head (Mt) 14.00
Motor HP 15.0
Minimum Efficiency 70 %
16
ESTIMATE FOR HVAC WORK
Make:-Xylem/Grudfoss/
Part I Equipment.
The price quoted for supply, installation, testing & commissioning shall be NO 2
inclusive of all duties & taxes, insurance, transportation / shipment cost from
works to site, loading / unloading, port clearance charges etc. as required in
Indian /Nepal Currency.
Part I Equipment.
17
ESTIMATE FOR HVAC WORK
The price quoted for supply, installation, testing & commissioning shall be NO. 1
inclusive of all duties & taxes, insurance, transportation / shipment cost from
works to site, loading / unloading, port clearance charges etc. as required in
Indian /Nepal Currency.
5) Air Separator
The price quoted for supply, installation, testing & commissioning shall be NO. 1
inclusive of all duties & taxes, insurance, transportation / shipment cost from
works to site, loading / unloading, port clearance charges etc. as required in
Indian /Nepal Currency.
18
ESTIMATE FOR HVAC WORK
Part I Equipment.
19
ESTIMATE FOR HVAC WORK
1b) 12,000 CFM, 50 mm St. Pr., 6 Row CC, 630 Dia Fan, NO 1
7.5 Kw Fan Motor.
Make:-Zeco/Crystal/Flaktwood
2a) For Level-2 CSU AHU NO 3
2,000 CFM, 40 mm St. Pr., 6 Row CC, 2 Row HC,
300 Dia Fan, 1.5 Kw Fan Motor.
20
ESTIMATE FOR HVAC WORK
For AHU NO 2
4000 CFM Supply Air, 8 Row CC, 2 Row HC, 125 mm
St. Pr., For Supply Fan, Supply Fan, 1200 CFM Ex. Air
Blower, 40 mm St. Pr. for Exhaust fan with other
accessories as specified)
21
ESTIMATE FOR HVAC WORK
4b) (4000 CFM Supply Air Blower, 8 Row CC, 2 Row HC, NO 1
140 mm St. Pr. for Supply Fan, 3500 CFM Ex. Air Blower,
60 mm St. Pr. for Exhaust fan with other accessories as
specified above)
22
ESTIMATE FOR HVAC WORK
5b) Level-1 NO 2
1500 CFM, 32 mm St. Pr., 6 Row CC, 1 x 250 Dia Fan,
0.75 Kw Fan Motor.
5c) Level-5 NO 1
2,500 CFM, 30 mm St. Pr., 6 Row CC, 1 x 280 Dia Fan,
1.1 Kw Fan Motor.
5d) Level-1 NO 1
3,000 CFM, 30 mm St. Pr., 6 Row CC, 1 x 300 Dia Fan
1 x 1.1 Kw Fan Motor.
5e) Level-3 NO 2
4,000 CFM, 35 mm St. Pr., 6 Row CC, 2 x 250 Dia Fan,
2.2 Kw Fan Motor.
5f) Level-3 NO 1
4,500 CFM, 35 mm St. Pr., 6 Row CC, 2 x 280 Dia Fan,
2.2 Kw Fan Motor.
5g) Level-3 NO 3
5,000 CFM, 40 mm St. Pr., 6 Row CC, 1 x 300 &
1 x 250 Dia Fan, 2.2 Kw Fan Motor.
5g) Level-5 NO 2
6,000 CFM, 40 mm St. Pr., 6 Row CC, 2 x 300 Dia Fan,
3.7 Kw Fan Motor.
23
ESTIMATE FOR HVAC WORK
1.5 TR NO 10
2.0 TR NO 5
2.5 TR NO 2
3.0 TR NO 1
24
ESTIMATE FOR HVAC WORK
Supply, installation, testing and commissioning of automatic control for Fan Set 53
Coil Units consisting of pressure independant balancing cum two way control
valve (already quantified above) & digital thermostat, which will have
provision of setting of room temperature, setting of fan speed (High, Medium,
Low) and shall display the inside RH.
Make:-Belimo/Siemens
25
ESTIMATE FOR HVAC WORK
Make:-Caryaire/Systemair
a) 300 CFM (8mm static pressure, single phase) NO. 10
b) 300 mm Dia NO 10
c) 450 mm Dia NO 5
26
ESTIMATE FOR HVAC WORK
Staircase
12000 CFM (15mm static pressure) For Lift Well Pressurization NO. 3
27
ESTIMATE FOR HVAC WORK
28
ESTIMATE FOR HVAC WORK
shall be class H
Make:-Greenheck/Kruger
18a) 10,000 CFM (40mm st. pr, 500 mm Dia Axial Fan, NO. 4
5 HP 1500 RPM Fan Motor, Direct Driven)
8,000 CFM (40mm st. pr, 500 mm Dia Axial Fan, NO. 2
5 HP 1500 RPM Fan Motor, Direct Driven)
7,500 CFM (40mm st. pr, 500 mm Dia Axial Fan, NO. 2
5 HP 1500 RPM Fan Motor, Direct Driven)
Supply, Installation , testing , commissioning and handing over of the Ultra LOT 1
Violet Germicidial Irradiatons (UVGI) System for maintaining indoor Air
Quality. The components of the system must be in strict conformity with the
specifications.and shall be including freight from works to site
,Insurance,Lifting,Shifting etc.as required . Single phase power supply for the
UVGI will be provided by others. The prices to include all inter connected
wiring between the UVGI Lamps. For Detail please refer the Basis of Design
For Selection.
Make:- Zeco/Pureair/Magneto
29
ESTIMATE FOR HVAC WORK
30
ESTIMATE FOR HVAC WORK
b) 65 mm dia NO. 6
c) 80 mm dia NO. 4
31
ESTIMATE FOR HVAC WORK
4c) Y-strainer
Make:-SKS/Audco/Leader/AIP
a) 25 mm dia NO. 9
b) 32 mm dia NO. 9
c) 40 mm dia NO. 11
d) 50 mm dia NO. 3
e) 65 mm dia NO. 13
f) 80 mm dia NO. RO
5) Thermometer
Supply, installation, testing and commissioning of alcohal fitted 'V' form NO. 10
thermometer of approved make conforming to tender specifications.
(For Floor Mounted AHU, Chiller)
Make:-Hguru/Fiebig.
6) Pressure Gauges
Make:-Hguru/Fiebig.
Supply, installation, testing and commissioning of pressure guage of NO. 20
approved make of dia 150 mm conforming to tender specifications.
(For Floor Mounted AHU, Chiller, & All Pumps)
7) Condensate Drain Piping
32
ESTIMATE FOR HVAC WORK
e) 65 mm dia RMT 30
33
ESTIMATE FOR HVAC WORK
a) 50 mm dia NO. 26
b) 65 mm dia NO. 6
c) 80 mm dia NO. 4
10f) Y-strainer
Make:- Armacell/Eurobatex/Vidoflex
a) 25 mm dia NO. 9
b) 32 mm dia NO. 9
c) 40 mm dia NO. 11
d) 50 mm dia NO. 3
e) 65 mm dia NO. 13
f) 80 mm dia NO. RO
34
ESTIMATE FOR HVAC WORK
11) Supply & Insulation of condensate drain water piping with Closed Cell
Elastomeric Nitrile Rubber of specified pipe section of specified thickness
in the tender specification.
Make:- Armacell/Eurobatex/Vidoflex
a) 25 mm dia pipe RMT 100
12) Supply, installation, testing and commissioning of auto air vent valve of
following sizes:-
Make:-Anergy/Spirotech
a) 10 mm dia auto air vent valve NO. 4
b) 24 G SMT 4000
c) 22 G SMT 800
d) 20 G SMT 700
e) 18 G SMT 200
35
ESTIMATE FOR HVAC WORK
Supply, fabrication, installation & testing of sheet metal ducting complete with
Spliter Damper vanes as required and as per ISI specifications and as
per approved shop drawings.
Make:- Jindal/Tata/Sail/lloyd
a) 24 G SMT 500
b) 22 G SMT 100
c) 20 G SMT 50
d) 18 G SMT 50
20 G SMT 200
16 G SMT 100
4) Supply and Application of accoustic lining on the supply air duct with 15 mm SMT 800
thk open cell nitrile rubber.
Make:-Armacell/Eurobatex/Vidoflex
5) Supplying and fixing of external thermal insulation on ducts with Closed Cell
Elastomeric Nitrile Rubber insulation, tape & adhesive (pidilite SR -998)
as required of following thickness.
Make:-Armacell/Eurobatex/Vidoflex
6) a) Fire Dampers
36
ESTIMATE FOR HVAC WORK
Supply, installation & testing of Duct / Wall mounted GI Fire Dampers SMT 30
actuated with the help of 24 V electric actuator and as per specifications
excluding actuator.
Make:-Crystal/Systemair
b) Damper Actuator
Make:-Belimo or Equivalent
Supply, installation and testing of Motorised Spring Return Actuator for NO. 50
devices upto 0.8 sq. metre with with control panel & temperature sensor.
c) Fresh / Exhaust air louvers with bird screen & damper SMT 20
i) 100 mm RMT RO
ii) 150 mm RMT RO
iii) 200 mm RMT RO
i) 2 Slot RMT 50
AHU ceiling and wall insulation: Providing and fixing Supplying of SMT 800
acoustic lining on wall and ceiling of AHU rooms with (UP TWIGA /ISOVER
MAKE) 25mm thick Rigid Board of Glass wool one side aluminum faced and
other side black glass cloth lamination, density 70 to 80 kg/cu.m
Make:- Uptwiga/Kimmco
9) Supply, installation and testing of multiblade box type Galvanized Sheet Steel SMT 50
construction damper for ducts to be provided with suitable links and
quadrants for control of volume of air.
Make:-Crystal/Systemair
10) Supply, installation and testing of multiblade box type
Aluminium Sheet construction damper for ducts
37
ESTIMATE FOR HVAC WORK
800 A electrically operated draw out type 4 Pole ACB with overload,
short ckt., earth fault, protection release, with 144 mm (0 -800 A)
ammeter with 3 CT and selector switch, 144 mm (0 - 500 V) Voltmeter with
selector switch, phase indication light with protection fuse, on / off / trip
indicating light with protection fuse. SET 02
b) Bus Coupler
38
ESTIMATE FOR HVAC WORK
B) OUTGOINGS
63 A TPN MCCB with 45 A star delta starter, overload relay, start/stop push
buttons, ammeter (0-63A) with three CT & selector switch, on/off/trip
indication lights with SP MCB, single phase preventer & auto / manual mode
selector switch. SET 02
39
ESTIMATE FOR HVAC WORK
2a) For AHU & 3 Phase Inline Fan, Pressurisation Fan, NO. 39
Ventilation Fan For Motor Up to 3.73 Kw
40 A TPN MCB with 16 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. Set - 01
2b) For AHU, Ventilation & Pr. Fan Motor 5.6 Kw NO. 16
40 A TPN MCB with 25 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. Set - 01
40 A TPN MCB with 16 A Star Delta starter, overload relay, start / stop
push buttons, phase indication lights with protection fuse, on / off / trip
indication lights with protection fuse, single phase preventer & auto / manual
mode selector switch. Set - 01
2d) For AHU & Ventilation Fan Motor 9.3 / 11.2 Kw NO. 1
63 A TPN MCB with 25 A Star Delta starter, overload relay, start / stop
push buttons, phase indication lights with protection fuse, on / off / trip
indication lights with protection fuse, single phase preventer & auto / manual
mode selector switch. Set - 01
40
ESTIMATE FOR HVAC WORK
63 A TPN MCB with 25 A Star Delta starter, overload relay, start / stop
push buttons, phase indication lights with protection fuse, on / off / trip
indication lights with protection fuse, single phase preventer & auto / manual
mode selector switch. Set - 01
INCOMER
OUTGOING
40 A TPN MCB with 16 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. SET - 02
40 A TPN MCB with 12 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. SET - 01
INCOMER
OUTGOING
41
ESTIMATE FOR HVAC WORK
40 A TPN MCB with 16 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. SET - 01
40 A TPN MCB with 12 A DOL starter, overload relay, start / stop push
buttons, phase indication lights with protection fuse, on / off / trip indication
lights with protection fuse, single phase preventer & auto / manual mode
selector switch. SET - 01
LOT
INCOMER
OUTGOING
63 A TPN MCB with 32 A Star Delta starter, overload relay, start / stop
push buttons, phase indication lights with protection fuse, on / off / trip
indication lights with protection fuse, single phase preventer & auto / manual
mode selector switch. SET - 02
16 A SP MCB SET 02
42
ESTIMATE FOR HVAC WORK
Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender.A) P
Make:-Rallison/Polycab/Havells
Part V Electrical Work.
4C x 16 Sq. mm RMT 50
4C x 25 Sq. mm RMT 50
4C x 4 Sq. mm RMT 75
4C x 6 Sq. mm RMT 50
4C x 10 Sq. mm RMT 20
4C x 16 Sq. mm RMT 50
43
ESTIMATE FOR HVAC WORK
i) Supply & laying of 32 x 6 mm copper strip recess / surface as strip earth lead
RMT including
20 soldering etc. as required
ii) Supply & laying of 25 x 3 mm copper strip recess / surface as strip earth lead
RMT including
20 soldering etc. as require
iii) Supply & laying of 4 mm dia. Copper wire or in recess for loop earthing asRMT
required.
80
iv) Supply & laying of 3 mm dia. Copper wire or in recess for loop earthing asRMT
required.
50
v) Supply and laying of rubber mat of size 1000 mm & 12.5 mm thick. RMT 20
6) Cable Tray
Make:-Soltco/Rico
Supply and installation of lader type 16 G GI perforated 'U' shaped channel 40mm x 20mm cable tray of following
NOTE:
The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode
44
ESTIMATE FOR HVAC WORK
45
ESTIMATE FOR HVAC WORK
46
ESTIMATE FOR HVAC WORK
Amount
Amount
47
ESTIMATE FOR HVAC WORK
Amount
48
ESTIMATE FOR HVAC WORK
Amount
Amount
49
ESTIMATE FOR HVAC WORK
50
ESTIMATE FOR HVAC WORK
Amount
Amount
0
16 38.4
51
ESTIMATE FOR HVAC WORK
Amount
Amount
52
ESTIMATE FOR HVAC WORK
Amount
53
ESTIMATE FOR HVAC WORK
Amount
Amount
54
ESTIMATE FOR HVAC WORK
Amount
55
ESTIMATE FOR HVAC WORK
Amount
56
ESTIMATE FOR HVAC WORK
Amount
0
0
57
ESTIMATE FOR HVAC WORK
Amount
58
ESTIMATE FOR HVAC WORK
Amount
59
ESTIMATE FOR HVAC WORK
Amount
60
ESTIMATE FOR HVAC WORK
Amount
Amount
61
ESTIMATE FOR HVAC WORK
Amount
Amount
62
ESTIMATE FOR HVAC WORK
Amount
63
ESTIMATE FOR HVAC WORK
64
ESTIMATE FOR HVAC WORK
Amount
Amount
65
ESTIMATE FOR HVAC WORK
Amount
66
ESTIMATE FOR HVAC WORK
Amt.
67
ESTIMATE FOR HVAC WORK
Amt.
68
ESTIMATE FOR HVAC WORK
69
ESTIMATE FOR HVAC WORK
Amount
70
ESTIMATE FOR HVAC WORK
Amount
Amount
71
ESTIMATE FOR HVAC WORK
Amount
72
ESTIMATE FOR HVAC WORK
Amount
73
ESTIMATE FOR HVAC WORK
Amount
74
ESTIMATE FOR HVAC WORK
n given in the tender.A) Power cabling (XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade) including cable
Amount
Amount
75
ESTIMATE FOR HVAC WORK
with auto / manual mode selector switch in the outgoing feeder for AHU Fan, Ventilation & Pressurization fan etc. to take fire input signal (P
76
ESTIMATE FOR HVAC WORK
77
ESTIMATE FOR HVAC WORK
78
ESTIMATE FOR HVAC WORK
Grade) including cable end termination with brass compression glands & aluminium lugs etc as per specification.
79
ESTIMATE FOR HVAC WORK
. to take fire input signal (Potential Free Contact). Cost shall be included in the panel price quoted by him.
80
SCHEDULE OF WORK FOR
A
1.0
1.1
1.2
1.3
1.4
1.5
B
1.0
2.0
4.0
4.1.1
5.0
32 HP
10 HP
Indoor Units
Cassette Type Units
1.05 TR
1.32 TR
1.65 TR
2.08 TR
2.64 TR
3.3 TR
4.12 TR
Remote Controllers
Wireless Remote Controller - Cassette/Hi-Wall Type Units
Wired Remote Controller - Ceiling Mounted Type Units
Refrigerant 'Y'Joint Required for distribution of refrigerant in copper piping etc complete as per specifications
Supply Installation testing & commissioning of main centralised controller with Touch Screen as per specifications to
hook up indoor units as mentioned above as well "Special Conditions".
Note : Electrical supply shall be provided by Electrical contractor to all VRV IDU Unit.
TOTAL
INDEGENIOUS ITEM
Weather Proof Isolators For outdoor Units
Weather proof Isolator box with ELCB or equivalent of suitable ratings near the outdoor units for power isolation for
outdoor VRV condensers. (Separate Isolator for each single Module of outdoor units)
The unit shall be supplied with electronic expansion valve/s (Dx), Drier, thermostats, control panel with wiring
& all accessories as required for completing installation. Fan outlet velocity shall not exceed 1800 FPM (9.1
MPS). Suspension arrangement for ceiling suspended AHUs shall also include spring type vibration isolators to make
the installation vibration free. AHUs shall be of following design parameters:
TOTAL
All outgoing shall be provided with Stop/Manual/ Auto/selector switch to facilitate operation through BAS. All starters
shall be provided with potential free Contact for Connections to Building Automation System.
A separate set of CTs to be provided for BAS and wiring from CTs and voltage transducers to be brought on to
separate set of terminals.
Incoming
One No. (400) amps TP microprocessor based MCCB complete with the following :
96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch through 415 V / 3 : 110 V /3 PT supply from
indicating light 1 Set
0 - (400) amps 96 x 96 sq mm digital ammeter with (400/5) amps CTs and selector switch. 1 Set
Over voltage tripping mechanism for persistent voltage exceeding 110% of the rated voltage for more than 5 minutes.
1 Set
Phase indicating light through 415 / 110 V supply from 415 V / 3 : 110 V / 3 PT, primary of PT shall be protected by
2 amps TP MPCB and secondary by 2 amps TP MCB and 25 amps 4 Pole RCCB of 30 mA 1 Set
TPN bus bars shall be of aluminium and shall be sleeved. Phase bus bars shall be rated at (630) amps and neutral bus
bar shall be of 50% capacity.
Maximum density of aluminium bus bars for current carrying capacity shall be one amp per square mm.
Outgoing
2 No. 63 amps TP MCCB outgoing feeders to OUTDOOR UNITS OF LEVEL-7 of capacity (Total 30 KW) and a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
2 No. 63 amps TP MCCB outgoing feeders to OUTDOOR UNITS OF LEVEL-8 of capacity (Total 30 KW) and a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
1 No. 40 amps TP MCCB outgoing feeders to OUTDOOR UNITS OF LEVEL-10 of capacity (Total 10 KWand a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
1 No. 40 amps TP MCCB outgoing feeders to OUTDOOR UNITS for TFA of capacity (Total 16 KWand a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
1 No. 40 amps TP MCCB outgoing feeders to OUTDOOR UNITS for TFA of capacity (Total 16 KWand a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
1 No. 63 amps TP MCCB outgoing feeders to OUTDOOR UNITS for TFA of capacity (Total 20 KWand a
indicating lamps with MCB for ON,OFF&TRIP status of motors(
1 No. 40 amps TP MCCB outgoing feeders to OUTDOOR UNITS for TFA of capacity (Total 8 KWand a indicating
lamps with MCB for ON,OFF&TRIP status of motors(
Supply, laying, fixing and Testing of the following sizes of 1.1 KV Copper conductor, PVC insulated, PVC
sheathed aromoured cables on the surface of wall/cable tray. Inclusive of all clamps,saddles,screws,cable identification
tags, cable terminal joints including terminal lugs and making connections with the equipment complete as per
the specifications and as required at site.
Supply and laying of Hot dipped Galvanized iron cable tray of the following sizes including all necessory fittings etc.
as per the specifications and as required to covered the exposed copper piping.
450 mm wide X 75mm X 2mm Thick with cover
300 mm wide X 75 mm X 2mm Thick with cover
20 mm
Supplying & drawing control cum transmission cable of size 2 core x 1.5 sqmm, copper conductor PVC insulated
PVC sheathed unaroured in the existing steel /PVC conduits pipes between indoor and outdoor unit including making
connections at both ends etc. complete as required.
TOTAL
Nos. 3 -
Nos. 1 -
Nos. 1 -
Nos. 2 -
Nos. 1 -
Nos. RO
Nos. RO
Nos. RO
Nos. RO
Nos. RO
Nos. RO
Nos. RO
Nos. 4 -
Nos. 5 -
Nos. 6 -
Nos. 6 -
Nos. 5 -
Nos. 42 -
Nos. RO
Nos. 42 -
Nos. 1 -
Nos. 8 -
Rmt 100 -
Rmt 75 -
Rmt 150 -
Rmt 75 -
Rmt 150 -
Rmt 110 -
Rmt 150 -
Rmt 200 -
Rmt 150 -
Rmt 20 -
Rmt 50 -
Rmt 100 -
Rmt 100 -
Rmt 150 -
Nos. 1 -
Nos. 2 -
Nos. 1 -
Rmt. 25 -
Rmt. 35 -
Rmt. 45 -
Rmt. 35 -
Rmt. 25 -
Rmt. 45 -
Meter 1000 -
A SUB-STATION EQUIPMENTS:
1.0 DG SETS.
C UPS SYSTEM :
99
1.0 EARTHINGS.
K INVERTOR:
1.0 INVERTOR.
100
M SAFETY EQUIPMENT :
GRAND TOTAL :
A SUB-STATION EQUIPMENTS:
Supply, installation, testing & commissioing of 2 pole structure with cross arms,
suitable clamps, insulators, disc insulators, 11KV lightning arrestors, complete
stay with insulator & wire, foundations, gang operated air break switch with
drop out fuses. This shall have termination arrangement for incoming &
outgoing through cable and necessary 6 inches dia GI pipe shall be provided for
cable support.
1 No
1.2a Installation of indoor metering unit (without CT, PT) as per the approved make of
DHBVN only. 1 No
1.2b Providing & fixing 11KV CT & PT in above metering indoor unit and getting them
calibrated from DHBVN before fixing. 1 Set
101
Supply and erection of the following equipment at suitable place in the sub-
station building as required and as per detailed specifications.
1.3a. First aid box as approved by St. John Ambulance Brigade/Indian Red Cross
Conforming to IS:2217 - 1963. 1 No
1.3b. Shock treatment chart at least in three languages duly mounted one wooden
frame with glass as required. 1 Nos
1.3e. Providing and fixing Medium Voltage Danger Notice Plate 200 mm x 150 mm
made of M.S. Steel at least 2 mm thick and vitreous enamelled white on both
sides and with inscription in single red colour on front side as required.
4 Nos
1.3f. Providing and fixing High Voltage Danger Notice Plate 250 mm x 200 mm made
of M.S. Steel at least 2 mm thick and vireous enameled white on both sides and
with inscription in single red colour on front side as required.
3 Nos
1.3g. Carbon dioxide (CO2) type fire extinguisher with suitable base pipe & horn
(conforming to IS 2876 with cylinders fully charged of capacity 9.0 Kgm). 2 Nos
1.3h. G.I buckets of followings capacity paint and written with white paint Fire and
mounted on M.S. angle iron bracket of sizes 50 mm x 50 mm x 6 mm thick and
500 mm long including grouting in wall etc. as required including filling with dry
sand 9 ltr capacity.
4 Nos
11KV 1 No. RMU having 3 nos. isolators with integral earth switch & 1 no VCB/
SF6 circuit breaker, VCB/ SF6 shall have self powered overcurrent ,short circuit
and earth fault relay, master trip relay, alarm & triping indication on Annunciator
window for buckholz, oil temp., winding temp.
102
(The cost shall includes the cost of all the test such as C.T. polarity test, primary
& secondary injection, meggar & H.V test and supply control cable between HT
panel to transformer. No extra claim for this shall be entertained)
1 Nos
103
4.1 b) 3c X 240sqmm 11KV (E) XLPE 100 Mtrs
4.2 a) Indoor heat shrink or 3M cold shrink type terminations for 3c x 185 sqmm XLPE
11KV (E)cable conforming to class I termination. (3M / Reychem) RO Nos.
4.2 b) Outdoor or 3M cold shrink type termination for 3c x 185 sqmm XLPE 11KV(E)
cable (confirming to class I termination). (3M / Reychem) RO No.
4.2 c) Indoor heat shrink or 3M cold shrink type terminations for 3c x 240 sqmm XLPE
11KV (E)cable conforming to class I termination. (3M / Reychem) 5 Nos.
4.2 d) Outdoor or 3M cold shrink type termination for 3c x 240sqmm XLPE 11KV
(E)cable (confirming to class I termination). (3M / Reychem) 1 No.
1.1 Supply, unloading, placing it on foundation of 500 KVA DG with PCC (PCC
incase of CUMMINS, EGCP for Cater Pillar or equvi. for other DGs) coupled to
500KVA alternator. Alternatorshall have inbuilt BTD and winding temp. detector
along with space heaters. Necessary differential/REF CTs shall be inbuilt inside
alternator box. ( MAKE : KOEL/CATERPILLAR )
104
- Suitable space heater for alternators.
- Suitable amended arrangement for bus duct and arrangement for mounting
differential /REF CTs.
- Suitable self priming pump with engine (if inbuilt in this model).
- DG shall be completely filled with luboil & HSD 990 ltr day tank shall be
completely filled. 1 Nos
1.2 Supply, unloading, placing it on foundation of 625 KVA DG with PCC (PCC
incase of CUMMINS, EGCP for Cater Pillar or equvi. for other DGs) coupled to
625 KVA alternator. Alternatorshall have inbuilt BTD and winding temp. detector
along with space heaters. Necessary differential/REF CTs shall be inbuilt inside
alternator box. ( MAKE : KOEL/CATERPILLAR )
- Suitable amended arrangement for bus duct and arrangement for mounting
differential /REF CTs.
- Suitable self priming pump with engine (if inbuilt in this model).
- DG shall be completely filled with luboil & HSD 990 ltr day tank shall be
completely filled.
1 Nos
105
2.1 Main DG Control Panel WITH PCC In CUMMINS Engine or suitable PLC
Controlller for other Makes, Load Management and AMF Feature for
1X500KVA DG + 1X6250KVA DG . ( MAKE : KOEL/CATERPILLAR )
Supply, erection, testing & commissioning of Main DG Control panel with PCC
for CUMMINS or EGCP or Equvi. controller for other makes, this will be floor
mounted, free standing, indoor duty, dust proof, vermin proof, front operated,
electrical panel fabricated, painted and manufactured exactly as per
specifications laid in this document and will be complete with the main and
auxiliary bus bars, interconnection, cable glands, earth terminals, earth bus and
will be powdered coated finished The DG control panel shall use all draw out 3
position withdrawn type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire
supply system and will have fault level of 65 KA The panel will be made as
per detailed specifications and drawings forming part of this document (Under
no case temperature of LT Panel shall be more at any point of the panel,
otherwise necessary exhaust fan shall be have to provided) Bus bar calculations
considering temperature derating, enclosure derating, sleeving derating must be
done and submitted for checking.
The DG vendor shall make complete protection curves and discrimination chart
for relay settings and shall adjust all these readings at site. The bus bar size shall
not be less than the ampere sizes mentions after derating and average derating
worked out by us is 0.66 The bidder will show exact calculations & compare the
figure of 0.66 and final calculations will be adopted for more stringent condition
The PCC panel will comprise of the following :
2.1a 2 Nos. incomer and out of 2 nos. 1 nos. will be 800A feeder incomer and 1 nos.
will be 1000A incomer. Each incomer breaker feeder shall have following :
106
- 1 No. combined digital KW, digital KWHr, digital power factor meter with
relevant CTs of class 1.0 accuracy. Field excitation D.C voltmeter analogue type
shall be provided.One no KW transducer shall also be provided .
- 1 No. combined over voltage, under voltage, under frequency and over frequency
relay with time delay element, 1 no. REF relay, 1 no. separate earth fault relay for
neutral circuit shall be provided, 1 no. reverse power relay for active & reactive
power, 1no. master trip relay shall be provided.
- Annunciation window to cover U/V, O/V, U/F, O/F, O/C, E/F, REF relay faults
shall be provided. Separate temp. indicator shall be made for BTD & RTDs.
- Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on
other faults.
- Initially U/V & U/F will be bye passed till oil pressure is picked up.
- Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter. D.C
voltmeter and ammeter will be analouge type.
- Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on
mains, D.G. fails to start.
- Generator start /stop facility through push button from panel, necessary cranking
relay shall be provided.
- 1 No TP 500A TP contactor (for non Cummins engine) for neutral closing along
with closing circuit from PLC as well as through mannual control.
2.1b 1 Nos. bus coupler 1000A 4P EDO ACB with over current, short circuit and earth
fault releases.
2.1c Bus Bar shall be suitable for carring 1250A in phases and 1000A in neutral.
2.1d OUTGOINGS
- 2 Nos. TPN feeder each comprising of 1 no. 1000A TP EDO ACB with
microprocessor based over current, short circuit, earth fault protections, ON /OFF
/TRIP indication.
2.1e Other items such as:
107
- 1 Lot of control wiring
- 1 Set of designation plates 1 Set
3.1.1 Supply, erection, testing and commissioning of MS pipes with bends & flanges
and all accessories complete in every way.
3.1.2 Insulation of above pipe with low resin bonded wool of min 75mm. thickness
min. 144Kg/ m3 density and 24 SWG Alm cladding inside & outside DG room
complete. Insulation will be done in such a way that temperature surrounding it
shall not exceed 7 deg. beyond ambient. The above specifications shall be based
on calculation subject to minimum ratings given above.
3.2.1 Supply, Erection, installation, testing & commissioning of 990 ltr. M.S diesel
tank with manholes cover, drain valve, marking along with M.S structure and
flame proof level switches.
1 Sets
3.2.2 Supply, installation, testing & commissioning of Class 'C' type following pipes
with 4mm PYPCOT coating.
- 25mm 30 Mtrs.
108
- 38mm 100 Mtrs.
3.2.3 Supply, installation, testing & commissioning of Class 'C' type following pipes.
- 25mm 30 Mtrs.
- 38mm 100 Mtrs.
C UPS SYSTEM :
a) THD(i) shall be less than 8% in the entire loading range of 25% to 50%.
b) Input power factor shall be more than 0.9. from 25% to 50% load
f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case
of 12 volt cells.
g) It shall have RS 485 port with modbus connectivity for BMS interfacing and
necessary protocols for LAN /WAN connectivity. All necessary software /
mapping to be built in for BMS compatibility. 3 Nos
a) THD(i) shall be less than 8% in the entire loading range of 25% to 50%.
109
b) Input power factor shall be more than 0.9. from 25% to 50% load
f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case
of 12 volt cells.
g) It shall have RS 485 port with modbus connectivity for BMS interfacing and
necessary protocols for LAN /WAN connectivity. All necessary software /
mapping to be built in for BMS compatibility. 3 Nos
1.2 BATTERY
( Make : Pegasus-AAL, GE Power, ABB )
1.2.1 Supply, installation, testing & commissioing of 1 X 60KVA UPS at 0.80 output
power factor strictly as per specification given in the document. Each individuals
UPS of 30KVA shall have 20 min. battery back up. The battery shall comprise of
12 volt cell and size and combination of bank in terms of VAH shall be clearly
mentioned with battery claculation with invertor efficiency as 0.94 or
less,deaging factor for battery shall be taken as 80%, end of cell voltage shall be
taken as 10.5 volts. The calculation of battery shall be attached with offer.
3 Nos.
1.2.2 Supply, installation, testing & commissioing of 1 X 40KVA UPS at 0.80 output
power factor strictly as per specification given in the document. Each individuals
UPS of 30KVA shall have 20 min. battery back up. The battery shall comprise of
12 volt cell and size and combination of bank in terms of VAH shall be clearly
mentioned with battery claculation with invertor efficiency as 0.94 or
less,deaging factor for battery shall be taken as 80%, end of cell voltage shall be
taken as 10.5 volts. The calculation of battery shall be attached with offer.
3 Nos.
110
Supply, unloading, shifting to foundation, assembly & commissioning of Main
LT Panel. This will be floor mounted, free standing, indoor duty, dust proof,
vermin proof, front operated, electrical panel fabricated as per specifications laid
in this document and will be complete with the main and auxiliary bus bars,
interconnection, earth bus and will be powder coated finish with 70 micron
thickness. The Main LT Panel shall use all draw out type breakers suitable for
415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Each incoming breaker
will have microprocessor based releases and all outgoing breaker will have
minimum electrostatic releases or mention as mention in BOQ. The Panel will be
made as per detailed specifications & drawings forming part of this document.
(Each MCCB will be variable current setting from front, with front extended
lockable handle, pad lockable in off position, indication light for ON, shrouding
on incomer side, termination shall be suitable for aluminium bus bars.)
(Under no case temperature of main LT panel shall be more at any point of the
panel. To avoid heating necessary exhaust fans shall have to be provided along
with top louvers).
(i) One number 1600A 4P EDO ACB incomer breaker from transformer having
microprocessor based, over current, earth fault, short ckt. with time delay
elements, 3 Nos. phase to neutral & neutral to earth spark gap surge suppresor
for 200KA with fuses, 3phase monitoring relay with phase sequence. This
incomer shall have digital multifunction meter with harmonics and RS 485 port
with matching cast resin CT's, volt meter, voltmeter selector switch,ammeter,
ammeter selector switch, indication lights for phases with MCB, ON /OFF /TRIP
indication light for spring charge, 1 no. reverse power relay.
(ii) One number 1000A 4P MCCB incomer breaker from DG synchronising panel
having microprocessor based, over current, earth fault, short ckt. with time delay
elements, 3 Nos. phase to neutral & neutral to earth spark gap surge suppresor
for 200KA with fuses, 3phase monitoring relay with phase sequence. This
incomer shall have digital multifunction meter with harmonics and RS 485 port
with matching cast resin CT's, volt meter, voltmeter selector switch,ammeter,
ammeter selector switch, indication lights for phases with MCB, ON /OFF /TRIP
indication light for spring charge, 1 no. reverse power relay.
111
(iii) One number 1250A 4P MCCB incomer breaker from DG synchronising panel
having microprocessor based, over current, earth fault, short ckt. with time delay
elements, 3 Nos. phase to neutral & neutral to earth spark gap surge suppresor
for 200KA with fuses, 3phase monitoring relay with phase sequence. This
incomer shall have digital multifunction meter with harmonics and RS 485 port
with matching cast resin CT's, volt meter, voltmeter selector switch,ammeter,
ammeter selector switch, indication lights for phases with MCB, ON /OFF /TRIP
indication light for spring charge, 1 no. reverse power relay.
B INTERLOCKING
- Interlocking logic electrical between three incomers and one nos. bus coupler
and it should have auto start and auto trip facility for automatic operation of the
breaker. Interlocking shall be done through PLC.
C BUS COUPLER
i) Two numbers 800A 4 pole EDO ACB as bus coupler with ON/OFF indication
and minimum electrostatic releases.
ii) Bus coupler shall be interlocked electrically with three incomers
iii) Only one incomers can be on at one time in one bus.
iv) Bus Coupler shall have electrostatics releases.
D BUS BAR
i) A set of TPN Aluminium bus bar rated for 1800A (after considering all necessary
deratings) 3 phase 4wire, 50Hz.
ii) A suitable minimum derating factor must be taken for calculation of bus bar
sizes. The bus bar size after derating shall be equal to the ampere given in the
iii) BOQ
The conductivity of bus bar shall not be less than 58% and earth bus size shall be
10% of phase bus bar.
i) 1 Nos. 1000A feeder each having 1 no. 1000A TP MDO ACB inbuilt
microprocessor based overcurrent, short ckt and earth fault releases with
ON/OFF/TRIP indication, 1 no. multifunction meter (showing all power
parameters) with RS 485 port with selector switch, matching cast resin CT's.
ii) 2 Nos. 800A feeder each having 1 no. 800A TP MDO ACB inbuilt
microprocessor based overcurrent, short ckt and earth fault releases with
ON/OFF/TRIP indication, 1 no. ammeter with cast resin CT's and ammeter
selector switch.
iii) 2 Nos. 400A TPN feeder each having one no. 400A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication.
112
vi) 12 Nos. 250A TPN feeder each having one no. 250A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication, 1 no.
multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
v) 3 Nos. 200A TPN feeder each having one no. 200A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication, 1 no.
multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
vi) 3 Nos. 160A TPN feeder each having one no. 160A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication, 1 no.
multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
vii) 5 Nos. 125A TPN feeder each having one no. 125A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication, 1 no.
multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
viii) 5 Nos. 100A TPN feeder each having one no. 100A TP MCCB's with
microprocessor based releases with isolable neutral ,ON indication, 1 no.
multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
- Other items such as
- A minimum derating factor must be taken for calculation of bus bar sizes. The
bus bar size after derating shall be equal to the ampere given in the BOQ The
conductivity of bus bar shall not be less than 58% and earth bus size shall be
minimum 10% of phase bus bar. Each MCCB shall have front extended operating
handle, door interlocked with handle,Variable current setting from front,
indication lights for ON, shrouding for incomer side. All 3 pole MCCB 's will
have isolable neutral.
A INCOMER
i) One number 250A incomer having TP+IN 250A MCCB.
ii) 1 no. multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
iii) 3 nos. phase indication lights
113
iv) 1 no. voltmeter, 1 no. VSS
B BUS BAR
One set of TPN, Al. bus bar rated 300 Amps (after considering necessary
deratings) for phases and neutral for half capacity of phases.
A INCOMER
i) One number 400A incomer having TP+IN 400A MCCB.
ii) 1 no. multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
iii) 3 nos. phase indication lights
iv) 1 no. voltmeter, 1 no. VSS
B BUS BAR
One set of TPN, Al. bus bar rated 300 Amps (after considering necessary
deratings) for phases and neutral for half capacity of phases.
A INCOMER
i) Two numbers 160A incomer each having 160A 4P MCCB.
ii) 1 no. multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
114
iii) 3 nos. phase indication lights
iv) 1 no. voltmeter, 1 no. VSS
B BUS BAR
One set of TPN, Al. bus bar rated 200 Amps on both sides (after considering
necessary deratings) for phases and neutral for half capacity of phases.
A INCOMER
i) 3 Nos. 125A TP MCCB incomer with microprocessor based, over current, earth
fault, short ckt. with time delay elements and ON/OFF/TRIP indication, 3 Nos.
phase to neutral &neutral to earth spark gap surge suppresor for 65KA with fuses.
This incomer shall have digital multifunction meter with harmonics and RS 485
port with matching cast resin CT's, volt meter, voltmeter selector switch,
indication lights for phases with MCB.
B BUS BAR
One set of TPN, Al. bus bar rated 150 Amps (after considering necessary
deratings) for phases and neutral for half capacity of phases.
C BUS COUPLER
i) One numbers 250A 4 pole MCCB as bus coupler with ON/OFF indication and
minimum electrostatic releases.
ii) One numbers 125A 4 pole MCCB as bus coupler with ON/OFF indication and
minimum electrostatic releases.
iii) Bus coupler shall be interlocked electrically with three incomers
iv) Only one incomers can be on at one time in one bus.
v) Bus Coupler shall have electrostatics releases.
115
- 1 set of complete wiring 1 No.
A INCOMER
i) 3 Nos. 100A TP MCCB incomer with microprocessor based, over current, earth
fault, short ckt. with time delay elements and ON/OFF/TRIP indication, 3 Nos.
phase to neutral &neutral to earth spark gap surge suppresor for 65KA with fuses.
This incomer shall have digital multifunction meter with harmonics and RS 485
port with matching cast resin CT's, volt meter, voltmeter selector switch,
indication lights for phases with MCB.
B BUS BAR
One set of TPN, Al. bus bar rated 150 Amps (after considering necessary
deratings) for phases and neutral for half capacity of phases.
C BUS COUPLER
i) One numbers 160A 4 pole MCCB as bus coupler with ON/OFF indication and
minimum electrostatic releases.
ii) Bus coupler shall be interlocked electrically with three incomers
iii) Only one incomers can be on at one time in one bus.
iv) Bus Coupler shall have electrostatics releases.
A INCOMER
i) Two numbers 200A incomer each having 200A 4P MCCB.
ii) 1 no. multifunction meter (showing all power parameters) with RS 485 port with
selector switch, matching cast resin CT's.
iii) 3 nos. phase indication lights
iv) 1 no. voltmeter, 1 no. VSS
B BUS COUPLER
116
One number 200A 4P MCCB as bus coupler with ON/OFF indication.
C BUS BAR
One set of TPN, Al. bus bar rated 300 Amps on both sides (after considering
necessary deratings) for phases and neutral for half capacity of phases.
One set of alm. 3 phase bus bar systems rated for 1250A for phases and neutral
after taking all derating factors.
- 2 nos x 10 KVAR capacitor banks each 10 KVAR (should offer net capacitance
of 10 KVAR at 415V after suitably derating from 525V capacitor) section will
have 100A fuse base with HRC fuses, with 1 no of 70amps TP contactor, 1 no.
10KVAR 7% harmonic block reactor with 200% linearity class H and
thermistors, net 10 KVAR heavy duty capacitor rated at 415V, 1 set lights
ON/OFF, 1 set of ON/OFF push buttons, 1 no. CT operated ammeter 0-50 amps.
2 nos. x 50 KVAR capacitor banks, each 50 KVAR (should offer net capacitance
of 50 KVAR at 415V after suitably derating from 525V capacitor) section will
have 160A fuse base with HRC fuses, with 1 no. of 110 amps TP contactor, 1 no.
50KVAR 7% harmonic block reactor with 200% linearity class H and
thermistors, 50 KVAR heavy duty capacitor rated at 415V, 1 set lights ON/OFF, 1
set of ON/OFF push buttons, 1 no. CT operated ammeter 0-100 amps.
117
3 nos. x 100 KVAR capacitor banks, each 100 KVAR (should offer net
capacitance of 100 KVAR at 415V after suitably derating from 525V capacitor)
section will have 250A fuse base with HRC fuses, with 1 no. of 200 amps TP
contactor, 1 no. 100 KVAR 7% harmonic block reactor with 200% linearity class
H and thermistors, 100 KVAR heavy duty capacitor rated at 415V, 1 set lights
ON/OFF, 1 set of ON/OFF push buttons, 1 no. CT operated ammeter 0-200 amps.
Each capacitor bank shall be able to operate in either manual or auto mode
individually through APCR relay and separately in auto mode. Actual capacitance
value will be high at 525V and each capacitors should be derated to offer value
given above at 415V.
- 1 set of complete wiring 1 Nos
118
3.2 Supplying, installing, testing and commissioning of cable end box of following
capacity on the existing rising mains and complete with stands, cable end box,
brass compression gland, inter connections, earthing etc. as required. (without
MCCB ). ( Make : Zukini-Legrand, Siemens-Sivacon, Schneider )
3.3 Supplying, installing, testing and commissioning of suitable sizes of Tap off box
with following sizes of MCCBs on the existing rising mains complete with
connections etc. as required:- (with MCCB).( Make : Zukini-Legrand,
Siemens-Sivacon, Schneider )
a) 250 A TPN Tap off box with MCCB 2 Nos.
119
d) 4 C X 6 Sq.mm Cu. PVC arm. 500 Mtrs.
1.2 Supply of following sizes of 1.1 KV grade multicore Copper conductor PVC
insulated cable conforming to IS:694/1990 complete with all latest amendments
etc. as required. ( Make : Rallison/Polycab/Havells )
(Un-armoured Cables)
120
TOTAL OF ( E ) 1.0 CARRIED OVER TO SUMMARY PAGE
2.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable 1.1
KV grade of following sizes direct in ground including excavation, sand
cushoning protective covering and refilling the trench etc. as required:-
2.1.2 Laying and fixing of one number PVC insulated and PVC sheathed/XLPE
aluminium conductor cable of 1.1 KV grade, of following sizes on cable tray /
surface as required:-
c) Exceeding 120 sq. but not exceeding 400 sq. mm 900 Mtrs.
2.1.3 Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of
1.1 KV grade of following sizes in the existing RCC/ HUME/ STONEWARE/
METAL pipe as required:-
121
3.1 Supply and making end termination with brass compression glands and
aluminium / copper lugs for PVC insulated and PVC sheathed aluminium /
copper conductor cable of 1.1 KV grade of the following sizes as required:-
( Make : Peeco, Comet )
122
s) 1 C X 240 Sq.mm Cu. PVC sheathed unarm. 4 Sets
4.2 Supply, fabrication and installation of pre galvanised factory built in ladder type
cable trays complete with all bends, tees, elbows, reducers etc. with rungs at
every 250mm spacing of various width in two tier/three/ five tier fashion either
on one side of the wall or on two sides of the wall or at other places and paint
afterward if required. (All bends & tees shall be of factory built-in of same
make as that of tray)
Supply, fabrication and installation of hangers and supports for cable trays of
various width in one/two/three tier fashion either on one side of the wall or on
two sides of the wall/column/truss or at other places as required as per drawing.
The work involves design of support system, fabrication of clamps, hooks, 4000 Kgs.
suspension rod or strip painted with two coats of red oxide and one coat
afterward with paint as per the approved colour. Before fabricating, the
contractor has to get the cable support design approved from the site
engineer/consultant.
4.4 GI Pipe
123
Supply and installation of `B' class 100 dia. GI pipe for cable sleeves in
recess/ on surface / Ground complete with all accessories pull boxes where ever
required, M.S. fish wire, fixing hardware etc. including the chasing of wall/
floor and plastering the chased portion, digging the trench and back filling,
making good the damages, sealing of pipe entry etc. as required:- ( Make :
Jindal -Hisar/Surya ) 20 Mtrs.
1.0 EARTHING :
Other hardware like nuts, bolts and washers should be of Stainless Steel.
124
1.5 Providing and fixing 50mm x 6mm GI strip in 80 mm dia. G.I. Pipe from earth
electrode as required. 100 Sets.
1.7 Providing and fixing 40mm x 6mm GI strip in 65 mm dia. G.I. Pipe from earth
electrode as required. 10 Mtrs.
1.9 Providing and fixing 25mm x 5mm GI strip in 40 mm dia. G.I. Pipe from earth
electrode as required. 250 Mtrs.
1.10 Supplying and laying 25 mm x 6 mm. GI strip at 0.50 m. below ground level as
strip earth electrode, including soldering etc. as required. 10 Mtrs.
1.11 Providing and fixing 50mm x 6 mm CU strip in 80 mm dia. G.I. Pipe from earth
electrode as required. 50 Mtrs.
1.12 Providing and fixing 25 mm x 5mm Copper strip on surface or in recess for
connections etc. as required. 50 Mtrs.
1.13 Providing and fixing 25 mm x 5mm Copper strip in 40 mm dia. G.I. Pipe from
earth electrode as required. 50 Mtrs.
1.14 Providing and fixing 6 SWG dia GI Wire on surface or in recess for loop earting
along with existing surface / recessed conduit submain wiring / cable as required. 900 Mtrs.
1.15 Supplying of following sizes of 1.1 KV grade multicore copper conductor XLPE
insulated armoured cable complete with all amendments etc. as required.
1.16 Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of
1.1 KV grade of following sizes in the existing RCC/ HUME/ STONEWARE/
METAL pipe as required:-
125
a) 1 C X 50 Sq.mm Cu. PVC sheathed unarm. 40 Mtrs.
1.17 Laying and fixing of one number PVC insulated and PVC sheathed/XLPE
aluminium/ copper conductor cable of 1.1 KV grade, of following sizes on cable
tray / surface as required:-
Providing and lying non-pressure NP2 class (light duty) R.C.C. pipes with collars
jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement :2
fine sand) including testing of joint etc. complete : ( Make : Pragati, Jain
Spun )
a) 150mm dia R.C.C. pipe 100 Mtrs.
b) 250mm dia R.C.C. pipe 150 Mtrs.
c) 300mm dia R.C.C. pipe 150 Mtrs.
126
Lot
2.3 Supply of heavy duty weather proof environment friendly polyplastic earth pit
chamber with cover of autolocking facility with the following dimensions -
254mm dia (top), 330mm dia (bottom) and 260mm height 4 knock-out openings 4 Nos.
at the bottom are provided for the easy interconnection of earth strips between the
earth pits to form a grid.
127
2.4 Test Link Joint in an IP 55 weather proof polyplastic enclosure of suitable 2 Nos.
dimension.
TOTAL OF (F) 2.0 CARRIED OVER TO SUMMARY PAGE
Supply, installation, testing, and commissioning of wiring with all the required
material for the following points with FRLS insulated, flexible multi stranded
copper conductor 1.5 sqmm 1100 Volts grade wires in concealed or surface
mounted 25mm diameter, medium duty PVC rigid/ flexible conduit or as
specified inclusive of ON/OFF Modular type switch wherever applicable and
earthing of MS switch box and fixtures by means of FRLS insulated, flexible
multi stranded copper conductor 1.5 sqmm earth continuity conductor laid in
common conduit including connections as required. Wiring include all necessary
associated hardware including ferrules at both end etc. as per the specifications
(the point to start from switch board & terminated to lighting fixture as
specified).
1.1 b) Primary Light point controlled directly by MCB in MCB distribution board. (MCB
covered in separate BOQ item.) 50 Nos
1.1 c) Extra Light point looped to primary point to be laid in conduit . 750 Nos
1.1 d) Same as boq item no. 1.1 b) but in MS medium duty conduit. 1 Nos
1.1 e) Same as boq item no. 1.1 c) Extra Light point looped to primary point to be laid
in MS medium duty conduit . 1 Nos
128
Supply, installation, testing, and commissioning of wiring with all the required
material for the following points with FRLS insulated, flexible multistranded
copper conductor 1.5 sqmm 1100 Volts grade wires in concealed or surface
mounted 25mm diameter, medium duty PVC rigid/ flexible inclusive of ON/OFF
Modular type switch wherever applicable and earthing of MS switch box and
fixtures by means of FRLS insulated, flexible multistranded copper conductor
1.5 sqmm earth continuity conductor laid in common conduit including
connections as required. Wiring include, fan box, fan hook, electronic regulator
and associated hardware etc. all necessary associated hardware including
ferrules etc. as per the specifications.
350 Nos
250 Nos
b) Extra loop point (on to next table), 6 amps , 5/6 pin modular type socket with
switch looped to other points with 2.5 sqmm FRLS multi stranded copper wire
and earthing with FRLS insulated, flexible multistranded copper conductor 1.5
sqmm earth wire. Point will terminate directly to the socket by using all
necessary accessories, flexible conduits etc. ( Make : Schneider,Siemens )
150 Nos
129
1.3.1 Supply, installation, testing, rectification, and commissioning of wiring with all
the required material for the following points with FRLS flexible multi-stranded
copper conductor 2.5 sqmm 1100 Volts grade wires in concealed or surface
mounted 25mm diameter, medium duty PVC rigid/ flexible of 6 Amps ON/OFF
modular switch, 2 nos. 5/ 6 pin socket 6 Amps modular socket in GI boxes and
earthing of fixtures and conduit pipe by FRLS insulated, flexible multistranded
copper conductor 1.5 sqmm (earth continuity conductor) laid in common
conduit including connections as required, all necessary associated hardware
including ferrules etc. as per the specifications. ( Make : Schneider,Siemens )
150 Nos
1.3.2 Extra loop point (on to next table), 6 amps , 2 nos. 5/6 pin modular type socket
with one no. 6 amps switch looped to other points with 2.5 sqmm FRLS multi
stranded copper wire and earthing with FRLS insulated, flexible multistranded
copper conductor 1.5 sqmm earth wire. Point will terminate directly to the
socket by using all necessary accessories, flexible conduits etc. ( Make :
Schneider,Siemens )
70 Nos
150 Nos
1.4.2 Extra loop point, 6/16 amps, 5/6 pin modular type switch with socket looped to
other points with 4 sqmm FRLS multi stranded copper stranded wire flexible
earth wire. Point will terminate directly to the socket by using all necessary
accessories, flexible conduits etc.
50 Nos
Supplying and fixing suitable size GI box with modular plate and cover in front on
surface or in recess, including providing and fixing 1 no. 6 pin 6/16 Amps
modular socket outlet and 16 Amps modular switch, connection, painting etc. as
required. (Point wiring shall be covered in separate BOQ item) . ( Make :
Schneider,Siemens )
1 Nos
130
1.5 INDUSTRIAL SOCKET WIRING
1.5.1 Supplying and fixing 32 amps, 230 volts, SPN industrial type, socket outlet, with
single pole and earth, metal enclosed plug top along with 32 amps 'C' series, SP,
MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover
for the socket outlet and complete with connections, testing and commissioning
etc. as required. (Circuit wiring/ cabling shall be covered in separate BOQ item)
( Make : Schneider,Siemens )
5 Nos
1.5.2 Supplying and fixing 32 amps, 230 volts, SPN industrial type, weather proof
socket outlet, with single pole and earth, with plug top along with 32 amps 'C'
series, SP, MCB, in ABS weather proof enclosure, on surface or in recess, with
cover for the socket outlet and complete with connections, testing and
commissioning etc. as required. (Circuit wiring/ cabling shall be covered in
separate BOQ item)( Make : Schneider,Siemens )
5 Nos
1.5.3 Supplying and fixing 32 amps, 415 volts, TPN industrial type, socket outlet, with
three pole and earth, metal enclosed plug top along with 32 amps 'C' series, TP,
MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover
for the socket outlet and complete with connections, testing and commissioning
etc. as required. (Circuit wiring/ cabling shall be covered in separate BOQ item) (
Make : Schneider,Siemens )
2 Nos
1.5.4 Supplying and fixing 32 amps, 415 volts, TPN industrial type, weather proof
socket outlet, with three pole and earth, with plug top along with 32 amps 'C'
series, TP, MCB, in ABS weather proof enclosure, on surface or in recess, with
cover for the socket outlet and complete with connections, testing and
commissioning etc. as required. (Circuit wiring/ cabling shall be covered in
separate BOQ item). ( Make : Schneider,Siemens )
RO Nos
1.5.5 Supplying and fixing 63 amps, 415 volts, TPN industrial type, weather proof
socket outlet, with three pole and earth, with plug top along with 63 amps 'C'
series, TP, MCB, in ABS weather proof enclosure, on surface or in recess, with
cover for the socket outlet and complete with connections, testing and
commissioning etc. as required. (Circuit wiring/ Cabling shall be covered in
separate BOQ item) ( Make : Schneider,Siemens )
RO Nos
131
Supply, installation, testing, rectification, and commissioning of wiring with all
the required material for the following points with FRLS insulated, flexible multi
stranded copper conductor 1.5 sqmm 1100 Volts grade wires in concealed or
surface mounted 25mm diameter, medium duty PVC rigid/ flexible inclusive of
ceiling rose near the fan, 6 Amps ON/ OFF modular switch with Light indication
in 2 mm thick GI boxes and earthing of Exhaust fan and conduit pipe by FRLS
insulated, flexible multi stranded copper conductor 1.5 sqmm and associated
hardware etc. as per the specifications.
36 Nos
Supply, installation, testing, and commissioning of wiring with all the required
material for the following points with FRLS insulated, flexible multistranded
copper conductor 1.5 sqmm 1100 Volts grade wires in concealed or surface
mounted 25 mm diameter, 2.0mm thick PVC rigid/ flexible inclusive of two sets
of 16 Amps ON/OFF modular switch, 6 pin socket 6/16 Amps modular socket in
GI boxes and earthing of fixtures and conduit pipe by 4 sq mm FRLS insulated
copper conductor (earth continuity conductor) laid in common conduit including
connections as required, all necessary associated hardware including ferrules
etc. as per the specifications. (For bracket fan in hall).
1 No
a Upto 450mm dia single phase, Heavy duty, 230 V AC, 50 Hz exhaust fan for main
hall complete with motor, capacitor, fan assembly mounting frame, louvers & all
accessories.
RO Nos
b Upto 300mm dia single phase, 230 V AC, 50 Hz exhaust fan for main hall
complete with motor, capacitor, fan assembly mounting frame, louvers & all
accessories.
36 Nos
c The 48 inch diameter, three blade, single phase, 230 volt AC, 50 Hz, ceiling fan
complete with the motor, starting capacitor, fan assembly, hang pipe, top bottom
domes, regulator, rubber bush, required hardware etc. The work involves the
assembly, testing, installation from the ceiling, connecting and commissioning of
the fan at site & all accessories.
132
1.9 CURCUIT AND SUB MAIN WIRING
Conduit ( Make : Rallion/akg)
Supply, carrying out sub main wiring with following copper stranded 1100 Volts
grade in concealed or surface mounted 25mm diameter, medium duty PVC
conduit along with FRLS insulated, flexible multistranded earth wire complete in
all respect with ferrules on the both end clearly marking the ckt no. (cost of
conduit shall be included)
1.9.1 2 x 2.5sqmm with 1 x 1.5sqmm earth wire in PVC conduit (DB to switch board)
1000 Mtrs
1.9.2 2 x 4.0sqmm with 2.5 sqmm earth wire in PVC conduit (for power sockets) 100 Mtrs
1.9.3 4 x 2.5sqmm + 2 x 1.5sqmm with earth wire in PVC conduit ( for 3 phase circuit
wiring wherever specified) 5 Mtrs
1.9.4 4 x 4.0sqmm with 2 x 2.5sqmm earth wire in PVC conduit ( circuit wiring for
3phase industrial / general power sockets or as specified in dwg) 5 Mtrs
1.9.5 4 x 6.0sqmm with 2 x 4.0 sqmm earth wire in PVC conduit ( circuit wiring for
3phase industrial / general power sockets os as specified in dwg) 5 Mtrs
1.9.6 4 x 10 sqmm with 2 x 6.0 sqmm earth wire in PVC conduit ( Submain wiring)
100 Mtrs
133
- 3 ph x 6 way MCB distribution board with one 40 amps Double pole RCCB in
each phase.
- 12 Nos. 6-20 Amps 10 kA SP MCB (Curve-C) for lighting spread equally in three
outgoing phase. 15 Nos
- 3 ph x 8 way MCB distribution board with one 63 amps Double pole RCCB in
each phase.
- 24 Nos. 6-32Amps 10KA SP MCB (Curve-C) for lighting & power spread equally
in three outgoing phase. 25 Nos
Supplying and fixing following way prewired Vertical TP&N type distribution
board of steel sheet suitable for 415 volts 4P MCCB upto 200A incomer & TP &
SP MCB outgoings mounted on surface/ recess (including structure fabrication
with anchor fastner/grouting bolts where required) complete with loose wire
box, terminal connectors for all incoming and outgoing circuits, duly prewired
with suitable size PVC insulated copper conductor up to terminal blocks, tinned
copper bus bar, neutral link, earth bar, din bar, detachable gland plate,
interconnections, powder painted including earthing etc. as required. as
specified.
134
- 5 nos. 3 pole MCB's (40A, Curve C).
- 15 nos. Single pole MCB's (32A, Curve C) as per DB detail/ SLD provided. RO No
2.1 Supplying of lighting fittings/ fixtures complete with internal wiring , special
electronics low loss ballast/ lumilux tube/ lamp/ condenser/ starter /louvers/
reflector/cover etc. complete in every way as required:- (Make :
Bajaj/Polycab/Visma)
d) Surface Mounted 2x15 watt LED Batten with 2x15W LED TUBE.
(Bajaj - BLRB-DB-218 WITH BLRB 15W CWc ) 120 Nos.
e) Surface Mounted 1x15 watt LED Batten with 1x15W LED TUBE.
(Bajaj - BLRB-DB-118 WITH BLRB 15W CWc ) 50 Nos.
j) Surface Mounted 80W watt industrial type LED HIGH BAY FITTING.
(Bajaj - BTS 80W WH LED ) 50 Nos.
135
l) Surface Mounted 20W LED ( BAJAJ FLEXITRON VIVA ) complete with all
acessories for Patient BED LIGHT.
(Bajaj - BLTRU 20W WH VIVA ) 295 Nos.
m) Surface Mounted track 12W LED light Suitable for 1 phase track ( 2 meter track
included for Musium.
(Bajaj - ALPHA 12W WH WITH VLTR 2M 1PH ) 2 Nos.
3.1 Supply, laying and installation of following trapezoidal PVC floor ducting
supplied in three meters per lenght including trunk connector, clamp, vertical/
horizontal bend etc in screed floor or on wall in line with EN 50085 including
chasing and refilling the trench as per the route shown in the drawing and
approved by consultant/ client at site including clamping & closing the open ends
temporarily by suitable end covers against entry of dust or any foriegn materials.
Installation rates of PVC trunk should be inclusive of necessary hardware and
arrangement required for fixing of trunk with duct connector and fastening
clamp. This activity also includes Duct connector, Fastening Clamp alongwith
associated accesories. (MAKE: OBO/Legrand )
136
3.2 Supply and installation of following floor slab box with fixed height of 55 mm
with GI trap and frame fitted with 1.5 mm flat GI load plate with flush floor
construction complet with UPVC duct entries on all four sides with possiblilty of
floor finishing materiel fixed directly on the flush floor.( MAKE: OBO )
The base floor boxes need to be supplied with fixed height for the first fix
installation. GI hardware to make the installation complete, like supply of
necessary screed anchors and grouting etc. including breaking walls, floors, etc.
for structures as required including supply of all GI hardware materials, all labour
and materials complete as per approved drawings, specifications of this tender
and directions of Engineer-in-charge including minor civil work.
3.2.1 325 mm x 325 mm GI under floor box suitable for three run of 90 x 35 mm
UPVC Duct entries on all side, and 325 mm x 325 mm square GI inspection 1 Nos.
cover complete with load plate . The floor boxes need to be supplied with flush
floor construction.
3.2.2 230 mm x 230 mm GI under floor box suitable for two run of 90 x 35 mm UPVC
Duct entries on all side, and 230 mm x 230 mm square GI inspection cover 2 Nos.
complete with load plate . The floor boxes need to be supplied with flush floor
construction.
3.2.3 165 mm x 165 mm GI under floor box suitable for single run of 90 x 35 mm
UPVC Duct entries on all side, and 165 mm x 165 mm square GI inspection 6 Nos.
cover complete with load plate . The floor boxes need to be supplied with flush
floor construction.
1.1 Supplying and fixing of Modular type RJ-11 telephone socket outlet in the
existing modular MS/GI sheet box and cover plate including connections etc
complete as required:- ( Make :Finolex/ Delton )
1.2 Supplying, drawing and wiring with soldered terminals on both ends of 0.61 mm
dia annealed tinned electrolytic grade copper conductor, PVC insulated,
twisted pairs bunched together in concentric layers so as to minimize crosstalk
and wrapped with melinex tape & overall PVC sheathed suitable for indoor
telephone wiring conforming to ITD-S/WS-113C and S/WS-114 in existing MS /
PVC conduit / raceways on surface / recessed / above falsecomplete as required:-
( Make :Finolex/ Delton )
137
b) 1 x 4 Pair 500 Mtrs.
1.3 Supply and installation of KRONE connector type main telephone tag block of
following sizes in sheet metal enclosure of suitable dimensions fabricated out of
16 SWG sheet steel with castle key lock, hinged type cover including termination
of telephone cables, making connections, painting of box etc. complete as
required:- ( Make :Finolex/ Delton )
a) 10 Pairs 5 Nos.
b) 20 Pairs 10 Nos.
c) 50 Pairs 10 Nos.
1.4 Supplying, laying, testing and terminating with soldered terminals on both ends
for 0.61 mm dia PVC insulated, PVC sheathed armoured annealed tinned
copper conductor, telephone Cables with GI wire / strip armouring generally
conforming to ITD specification S/WS-113C & S/WS-114 on surface / recessed /
false ceiling / cable Tray / GI pipe / Hume pipe etc. complete as required:-
( Make :Finolex/ Delton )
a) 10 Pairs 50 Mtrs.
d) 70 Pairs 10 Mtrs.
Note: Supply & installation of telephone equipment is not covered in this part.
2.1 Supplying and fixing of Modular type TV Co-axial socket outlet in the existing
modular MS / GI sheet box and cover plate inculading connections etc complete 20 Nos.
as required:- ( Make : Netgear/ catvision )
138
2.2 Supply and drawing of following solid annealed bare electrolytic grade copper
conductor with gas injected physical foam PE dielectric, poly-laminated
aluminium tape followed by copper braiding, jelly filled and overall PVC
sheathed in existing conduit pipe including connections complete as required:
( Make : Netgear/ catvision )
a) TV Cable RG-6 400 Mtrs.
2.3 Supply and fixing of TV Splitter in the existing MS / GI box including making
connections with thimbles/ connectors etc. as required. ( Make : Netgear/
catvision )
a) Two Nos. outgoing 2 Nos.
139
a) 9 Unit Wall Mounted Rack with fan and power strip with spike arrestors. 10 Nos.
b) 12 Unit Wall Mounted Rack with fan and power strip with spike arrestors. 1 Nos.
c) 15 Unit Wall Mounted Rack with fan and power strip with spike arrestors. 2 Nos.
d) 18 Unit Wall Mounted Rack with fan and power strip with spike arrestors. 20 Nos.
e) 48 Unit Floor Mounted Rack with power strip with spike arrestors. 4 Nos.
3.5 Supplying & installation of following size of Rack mounted LIU box complete
with SC Coupler panel, adapter plates including terminating the fibre optic cables
etc. complete as required:-
3.6 Supplying, installation, testing & commissioning of 24 port Patch Panel with
10 Nos.
individual Cable manager in the existing LIU box complete as required.
a) SC Connectors. 10 Nos.
140
a) Managable Gigabit desktop edge switches - with 24 Port 10/100/1000 Mbps,
Half/Full duplex, switched ports and with expansion ports for stacking additional 20 Nos.
switches suitable for Cat- 6 and above as required. (only cisco make)
c) Gigabit Ethernet 1000 base-T to 1000 base - SX Tranceiver.(only cisco make) 25 Nos.
4.1.1 Supply, installation, testing and commissioning of Main Control panel with 6
Zones expandable to 60 zone, compliant to IEC 60849 Evacuation Standards,
fully supervised and with digital pre-recorded messages, with Cat-6 connectivity 1 No.
complete with connections etc. complete as required.
4.1.2 Supply, installation, testing and commissioning of Voice Alram Call Station
2 No.
with mounting box etc. complete as required.
4.2 Amplifiers :
4.2.1 Supply, installation, testing and commissioning of Booster Amplifier 480 Watt
7 No.
complete with connections, connecting wires etc. complete as required.
4.2.2 Supply, installation, testing and commissioning of Booster Amplifier 240 Watt
2 No.
complete with connections, connecting wires etc. complete as required.
4.3 Speakers :
4.3.1 Supply, installation, testing and commissioning of False Ceiling Mounted High
Quality Polycarbonate 6 Watt Ceiling Speaker with connections, connecting 260 No.
wires etc. complete as required.
141
4.3.2 Supply, installation, testing and commissioning of 12 W Volume Control
80 Nos.
complete with mounting box, cover etc complete as required.
4.6 Wiring:
4.6.1 Supply, drawing, testing & commissioning of 4 pair UL listed CAT-6 UTP
400 Mtrs.
cable of 24 AWG solid copper conductors etc. complete as required.
4.6.2 Supplying and drawing of 1 pair 24/.20 (0.75 sq.mm), twisted, stranded annealed
electolytic copper conductor, colour coded, PVC sheathed and insulated FRLS 2000 Mtrs.
wire, in 25mm recess / surface PVC conduits including connections etc. complete
as required.
4.6.3 Supply, installation, testing & commissioning of 4" by 4" junction box etc.
150 Nos.
complete as required.
1 Nos.
142
7.3 1/3" CCDsensor, PAL:976H * 496 (V), 0.1 Lux/ F1.2 (0Lux, IR ON), internal sync.,
10~15 Meters (With 24 units IR LED), 800 TVL VADAL IR DOME CAMERA. 800 TVL
FIXED METAL IR DOME CAMERA
54 Nos.
7.4 1/3" CCDsensor, PAL:976H * 496 (V), 0.1 Lux/ F1.2 (0Lux, IR ON), internal sync.,
10~15 Meters (With 24 units IR LED), 700 TVL VADAL IR DOME CAMERA. 700 TVL
FIXED METAL IR Bullet CAMERA
4 Nos.
7.5 2 TB Sata HDD 2 Nos.
7.6 4 Amp power supply for 4 camers 20 Nos.
7.7 CABLE RG59 with power for each camera (Average length - 25Mtr.) 74 Nos.
7.8 Installation of software & setting of internet Iphone live watching from anywhere
complete in all respect. 1 LOT
7.9 21" Color flat panel LCD Monitor,500TVL, 800 x 600 resolution, inputs.
230VAC/50 Hz. At security control room 2 Nos.
143
1.5 Supply Installation, Testing & Commissioning of UL listed Intelligent
20 Nos.
addressable Manual Call Point / Pull station complete as per specification.
1.9 Supply Installation, Testing & Commissioning of wall mounting Hooter suitable
20 Nos.
for Alarm siren with suitable power supply unit.
1.11 Supply Installation, Testing & Commissioning of wall mounting strobe with
10
suitable power supply unit. Nos.
1.13 Supply Installation, Testing & Commissioning of Fire fighters telephone handset. 18 Nos.
144
1.1 Supply Installation testing and commissioning of Octagonal MS poles ( Height
7 mtr , Bottom dia 150mm Top dia 75 mm ) with base plate ( 16 mm thick ) and
decorative Street Lantern/Luminaire 1 x 150 watt street light fixture with lamp,
controlgear etc. complete with all accessories of Bajaj Cat No - BJWRL 150 SV
or approved equivalent (Minimum IP-66 ), die cast aluminium supporting ring
and transition plate, painted metallic, upper hemisphere spun aluminium and
painted metallic, single piece deep draw aluminium anodized reflector sealed on
to a toughened glass protector , control gear suitable for 220-240 V50 HZ,
horizontal mounting and 60 mm dia arm complete with 150 watt SV lamp of
approved make.
7 mtr. Pole (Single Bracket ) 12 Nos
1.2 Supply Installation testing and commissioning of 150W luminaire with lamp
(Bajaj Cat No BGWRL 150SV ) With 150w sodium vapour lamp or approved
equivalent (Minimum IP-66 ).(Make : Bajaj/Polycab/Visma)
12 Nos
1.3 Supply Installation testing and commissioning of Circular GI pols ( Height 3 mtr
) with base plate and decorative Street Lantern/Luminaire 1 x 150 watt street
light fixture with lamp, controlgear etc. complete with all accessories of Bajaj Cat
No - BEIP3M SA 150W or approved equivalent (Minimum IP-54 ), painted
black, single piece dish install on single arm , control gear suitable for 220-240
V50 HZ, fully vermin & weather proof complete with 150 watt MH lamp of
approved make. (Make : Bajaj/Polycab/Visma)
10 Nos.
1.4 Supplying and drawing following sizes of PVC insulated FRLS Copper
Conductor single core cable in the existing surface / recessed steel/PVC conduit
as required:-
a) 3 x 1.5 sq. mm 400 Mtrs.
1.6 Supplying, installation, testing & commissioning of 3 W LED Drive over light
fitting with lamp, Drivers and other accessories on ground complete with
connections etc. complete as required. (Make : Bajaj/Polycab/Visma)
10 Nos.
1.7 Supplying, installation, testing & commissioning of 3 W LED under water light
fitting with lamp, Drivers and other accessories on ground complete with
connections etc. complete as required. (Make : Bajaj/Polycab/Visma)
RO Nos.
1.8 Supplying, installation, testing & commissioning of Gate Light fitting with 80
watt HPMV lamp (Bajaj BNCL7SVO Complite). (Make : 4 Nos.
Bajaj/Polycab/Visma)
145
1.9 Supplying, installation, testing & commissioning of Flood Light fitting with 250
watt MH lamp (Bajaj BJFL 250 MH). (Make : Bajaj/Polycab/Visma) 10 Nos.
a) INCOMER :
i) 63 A 4 pole MCCB (10 KA) with On / Off indications in the front (ISI marked)
ii) LED Type Phase indicating - (R,Y& B) Lamps provided with 2A SP MCBs for
protection having lens and lamp openable from the top.-3 nos.
b) OUTGOING:
c) CONTROL:
ii) Time Switch with Daily dial, suitable for operation on 230 Volt, Single phase, 50
Hz, AC Supply - 2 Nos.
K INVERTOR:
146
1.0 5KVA INVERTER :
147
1.4 Bedside Push Cord:-
1.4.1 Supplying and fixing of UL listed 6 feet long Push Cord Set with Push button
switch on the existing Bed side Nurse call module complete as required.
( Make : Systematic )
100 Nos.
1.5.1 Supplying and fixing of UL listed Corridor Dome light including surface /
recessed mounted box complete with lamp etc. including connections etc as
required. ( Make : Systematic ) 45 Nos.
1.6 Wiring:-
1.6.1 Supplying, drawing, testing and commissioning of 4 pair UL listed Cat-6 UTP
cable of 24 AWG solid copper conductors in existing conduit/ raceway etc.
complete as required. ( Make : Systematic )
1000 Mtrs.
M SAFETY EQUIPMENT
1.1 Supplying and erection of the following equipment at suitable place in the sub-
station building as required:-
a) M.S bucket of 9 liters capacity painted with red oxide paint & lettered as 'Fire'
with White and red mounted on freestanding stand, as required including filling
with dry sand. 10 Sets.
b) First aid box as approved by St.John Ambulance Brigade /Indian Red Cross
society conforming to IS : 2217 - 1963. 4 Nos.
c) Shock treatment chart duly mounted on a wooden frame with glass on, as
required in 2 languages (Hindi & English). 4 Nos.
148
1.2 Supply and fixing of Carbon Dioxide fire extinguishers of 4.5 Kg each
mounted on wall hooks as per IS 2878-1976. 5 Nos
1.3 Supply and fixing of Carbon Dioxide fire extinguishers of 9 Kg each mounted
on wall hooks as per IS 2878-1976. 6 Nos
1.4 Providing and fixing MV danger notice plate of 200 mm x 150 mm made of
mild steel at least 2mm thick & vitreous enamelled white on both sides and
with inscription in signal red colour on front side as required. 10 Nos.
1.5 Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild
steel at least 2mm thick & vitreous enamelled white on both sides and with
inscription in signal red colour on front side as required.
10 Nos.
149
devices and all electrical connections and all electrical connections.
TERMINAL ARRANGEMENTS :
Cable box will be provided for input and output terminals to receive PVC Cables.
CENTRAL CONSTRUCTIONAL FEATURES :
The unit shall have two distinct features as under :-
I) MOTOR CONTROL :
Raise /Lower push button control by means of small single phase reversible
geared motor of the permanent capacitor type shall be provided. The Limit
Switches shall be provided to restrict the travel at extreme positions. with this
arrangement, it would also be possible to provide remote control of the
Regulating Unit. The reversible geared motor would of STEP-SYN type.
150
A Cable Management system which provide seals at cable and pipe entry points
in Panels,Control rooms walls,cable trench & outside control room,control
box,auxiliary service room wall/sub stations walls/floor sandat points where
cables pass from one chamber to another chamber to protect against hazards such
as Fire,Dust,Water, Snakes/Lizards/Rodents,Temperature Variations,Noise
etc.which can affect safety of costly equipments and affect the overall
operations.
151
TOTAL AMOUNT
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
152
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
153
0.00
0.00
0.00
0.00
0.00
RATE AMOUNT
154
0
0.00
155
0
0.00
0.00
156
0
0.00
157
0
0.00
158
159
160
0
0.00
161
0
0
0
0.00
162
0
0.00
163
164
165
0
166
0
167
0
168
0
169
0
170
0
0.00
171
0
0.00
172
0
173
0.00
0.00
174
0
175
0
0.00
176
0
0.00
177
0
178
0
0
0
0
0.00
0.00
179
0.00
0.00
0.00
180
0.00
0.00
181
0
182
0
183
0
184
0
0
0
185
0
186
0
187
0.00
188
0
0.00
189
0
0.00
190
0
0.00
191
0
0.00
192
0
193
0
0.00
194
0
0.00
195
0
0
0
0
0
0.00
196
0
0.00
197
0
198
0
0.00
0.00
199
0
0.00
200
0
0.00
201
0
0.00
202
0.00
203
0.00
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
ESTIMATE FOR HVAC WORK
SUMMARY OF PRICES
2.2 Web Based Software shall have the features to calculate the LOT 1
total power consumption, total refrigeration load consumed on
every day etc. Critical alarms generated in a day and its status
should also be mailed along with daily report.
B) Supervisory Controllers
257
ESTIMATE FOR HVAC WORK
258
ESTIMATE FOR HVAC WORK
8 Differential pressure switch for AHU pre, fine & hepa filter No. 70
9 status
Temperature sensor for return temperature monitoring No. 50
11 Digital electronic multimeter No. 10
12 Pressure Transducer No. 4
Notes:
259
ESTIMATE FOR HVAC WORK
260
ESTIMATE FOR HVAC WORK
261
ESTIMATE FOR HVAC WORK
Amount
Amount
262
ESTIMATE FOR HVAC WORK
Amount
0
0
0
0
263
ESTIMATE FOR HVAC WORK
0
0
0
0
Amount
0
0
0
0
Amount
264
ESTIMATE FOR HVAC WORK
265
ESTIMATE FOR HVAC WORK
266