2
SPROUT-MATADOR
FEED TECHNOLOGY
@ 4. ADJUSTMENT OF MATERIAL FLOW
Air intake and stone trap must be adjusted during grinding to allow observation of the
material flow during adjustment. .
Adjustment plate
Air intake
Fig.1
Depending on the nature of the material, the separator is adjusted to make the material
flow as shown in Fig. 1
Ifthe stone trap is filled with material, the air amount is increased by opening the air
intake,
The air intake must not be more than half closed.
The adjustment plate is used for subsequent adjustment by increasing/reducing the gap
over which the material is to be lifted.___. SPROUT-MATADOR
FEED TECHNOLOGY
@ 2. cLEANING
The separator magnet and stone trap are cleaned daily.
IMPORTANT! IMPORTANT! IMPORTANT! |
FAN AND HAMMERMILL MUST BE DISCONNECTED DURING CLEANING TO
PREVENT FOREIGN MATTERS FROM BEING SUCKED INTO THE MILL |
Metal parts filling the magnet may prevent an optimum spread of products over the mill
width. This will result in an uneven wear of grinding bridges, hammers and screens.
The magnet is cleaned by releasing the outer ball handle (item 1) and turning the magnet
(item 2) by means of the inner ball handle (item 3). The magnet is scraped or swept clean
of metal parts.
The stone trap is cleaned by loosening the hand screws (item 4) and turning them aside.
The trap (item 5) is pulled out and emptied___________ SPROUT-MATADOR
FEED TECHNOLOGY
® 3. REPLACEMENT OF SEPARATOR MAGNET
See figure 5 simultaneously
1. The nuts (item 1) are loosened.
2. The magnet box (item 2) is loosened by releasing the outer ball handle (item 3)
3. The magnet box is opened by turning the inner ball handle (item 4).
NOTICE! Be aware that the magnet box lies loose in the turning fittings.
4, The magnet (item 5) is removed
5. The magnet is remounted in opposite order.SPROUT-MATADOR
FEEDTECHNOLOGY
@ 4. SPARE PARTS LIST
ORDERING OF SPARE PARTS
With your order for spare parts please state the ID No. and ORDER NO. which appear
from the machine sign.
You can fill in a copy of this page and fax it to SPROUT-MATADOR AIS, att. Spare parts.
FaxNo, +45 7216 0301
Phone: +45 7216 0300
Example.
SPARE PART ID NO. DESCRIPTION NOS.
529887 Magnet 1
SPARE PARTS ID NO. DESCRIPTION NOS.
FIRM
CONTACT PERSON
ADDRESS
PHONE
FAX NO.
e HAMMERMILL ID NR.
ORDER NO.~ ___________ SPROUT-MATADOR
FEED TECHNOLOGY
e SPARE PARTS LIST
ITEM. | DESIGNATION |NOS.| 301 601 801 1001
1 |Felt 1 520894 | 520894 | 520894 | 520894
2 [Magnet 1 529887 | 529888 | 529889 | 527571
3__ [Housing 1 531625 | 531736 | 529441 | 527466
4 [Magnet box 1 531753 | 531744 | 529445 | 527469
5 [Air slide 1 531754 | 531740 | 529447 | 527456
6 [Inspection pane 2 511041 | 511041 | 511041 | 511041
7___| Thumb screw 5 501976 | 501976 | 501976 | 501976
8 | Flanged bearing 2 526226 526226 | 526226 | 526226
9 [Guide hub 1 527480 | 527480 | 527480 | 527480
528148 528148 | 528148 | 528148
576523 | 576523 | 576523 | 576523
531755 531741 529446 | 527462
531748 | 631739 | 529440 | 527472
503525 | 503525 | 503525 | 503525
11_[Parallel key
12_|Ball handel
13_ [Adjustment plate
14 [Stone trap
15__[Sponge rubber