Академический Документы
Профессиональный Документы
Культура Документы
PWC
A
B
SECTION
POWER WINDOW CONTROL SYSTEM C
E
CONTENTS
PRECAUTION ............................................... 4 RETAINED PWR : CONSULT Function (BCM - F
RETAINED PWR) ....................................................14
PRECAUTIONS ................................................... 4
Precaution for Supplemental Restraint System ECU DIAGNOSIS INFORMATION .............. 15 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 4 BCM (BODY CONTROL MODULE) ................. 15
Precaution for Work .................................................. 4 List of ECU Reference .............................................15
H
PREPARATION ............................................ 5 POWER WINDOW MAIN SWITCH ................... 16
Reference Value ......................................................16
PREPARATION ................................................... 5 Fail Safe ..................................................................17
I
Special Service Tool ................................................. 5
WIRING DIAGRAM ...................................... 18
SYSTEM DESCRIPTION .............................. 6
POWER WINDOW SYSTEM ............................. 18 J
COMPONENT PARTS ........................................ 6 Wiring Diagram ........................................................18
Component Parts Location ...................................... 6
Component Description ............................................. 6 BASIC INSPECTION ................................... 25
PWC
SYSTEM .............................................................. 8 DIAGNOSIS AND REPAIR WORKFLOW ........ 25
System Diagram ....................................................... 8 Work Flow ................................................................25
System Description ................................................... 8 L
ADDITIONAL SERVICE WHEN REMOVING
Fail-safe .................................................................... 9
BATTERY NEGATIVE TERMINAL ................... 27
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI- Description ...............................................................27
Work Procedure .......................................................27 M
GENT KEY SYSTEM) .........................................11
COMMON ITEM ......................................................... 11 ADDITIONAL SERVICE WHEN REPLACING
COMMON ITEM : CONSULT Function (BCM - POWER WINDOW MAIN SWITCH ................... 28 N
COMMON ITEM) ..................................................... 11 Description ...............................................................28
Work Procedure .......................................................28
RETAINED PWR ....................................................... 12
RETAINED PWR : CONSULT Function (BCM - SYSTEM INITIALIZATION ................................ 29 O
RETAINED PWR) ................................................... 12 Description ...............................................................29
Work Procedure .......................................................29
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- P
TELLIGENT KEY SYSTEM) ...............................13 ANTI-PINCH INSPECTION ............................... 30
Description ...............................................................30
COMMON ITEM ......................................................... 13 Work Procedure .......................................................30
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ..................................................... 13 DTC/CIRCUIT DIAGNOSIS ......................... 31
RETAINED PWR ....................................................... 14 POWER SUPPLY AND GROUND CIRCUIT .... 31
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work INFOID:0000000009757208
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.) C
Tool name
— Removing trim components
(J-46534) D
Trim Tool Set
AWJIA0483ZZ
PWC
AWKIA2052ZZ
1. BCM (view under instrument panel 2. Front power window motor LH (RH 3. Rear power window motor LH (RH
on the left side of the vehicle) similar) (view with front door finisher similar) (view with rear door finisher
removed) removed)
4. Main power window and door lock/ 5. Power window and door lock/unlock 6. Rear power window switch RH (LH
unlock switch switch RH similar)
7. Front door lock assembly LH (key 8. Front door switch LH (RH similar)
cylinder switch)
Component Function A
• Supplies power to power window switches.
BCM
• Controls retained power.
• Integrates the ENCODER POWER and WINDOW MOTOR. B
• Starts operating with signals from main power window and door lock/unlock switch.
Front power window motor LH
• Transmits power window motor rotation as a pulse signal to main power window and
door lock/unlock switch.
C
Starts operating with signals from main power window and door lock/unlock switch &
Front power window motor RH
power window and door lock/unlock switch RH.
Main power window and door lock/un- • Directly controls all power window motor of all doors.
lock switch • Controls anti-pinch operation of front power window LH. D
Power window and door lock/unlock
Controls front power window motor RH.
switch RH
E
Rear power window switch Controls rear power window motors LH and RH.
Starts operating with signals from main power window and door lock/unlock switch &
Rear power window motor
rear power window switch.
F
Front door switch LH or RH Detects door open/close condition and transmits to BCM.
PWC
AWKIA2893GB
Input signal to main power window and Main power window and door
Item Actuator
door lock/unlock switch lock/unlock switch function
Encoder Encoder pulse signal
Main power window
Front power window motor LH UP/
and door lock/unlock
DOWN signal
switch
Front power window motor
Power window and
Front power window motor RH UP/ Power window control
door lock/unlock
DOWN signal
switch RH
BCM RAP signal
Rear power window Rear power window motor UP/DOWN
Rear power window motor
switch signal
Fail-safe INFOID:0000000009757214
L
FAIL-SAFE CONTROL
Switches to fail-safe control when malfunction is detected in the encoder signal that detects UP/DOWN speed
and direction of door glass. Switches to fail-safe control when an error beyond the regulation value is detected
between the fully closed position and the actual position of the glass. M
Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe
control when malfunction is found in power window switch or in motor.
SYSTEM APPLICATION
G
BCM can perform the following functions.
I
System Sub System
ECU identification
Configuration
Work support
Data Monitor
J
Active Test
PWC
Door lock DOOR LOCK × × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × L
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
M
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
Air conditioner AIR CONDITIONER × N
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
DATA MONITOR
SYSTEM APPLICATION
G
BCM can perform the following functions.
I
System Sub System
ECU identification
Configuration
Work support
Data Monitor
J
Active Test
PWC
Door lock DOOR LOCK × × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × L
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
M
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × N
Air conditioner AIR CONDITIONER ×
Combination switch COMB SW ×
BCM BCM × × × × × O
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
P
Trunk open TRUNK ×
RAP system RETAINED PWR × ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
Panic alarm system PANIC ALARM ×
DATA MONITOR
WORK SUPPORT
ECU Reference C
BCS-29, "Reference Value"
BCS-46, "Fail-safe"
BCM D
BCS-48, "DTC Inspection Priority Chart"
BCS-49, "DTC Index"
E
WITHOUT INTELLIGENT KEY SYSTEM
ECU Reference F
BCS-97, "Reference Value"
BCS-108, "Fail-safe"
BCM G
BCS-108, "DTC Inspection Priority Chart"
BCS-109, "DTC Index"
PWC
TERMINAL LAYOUT
AWKIA2892ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color)
Condition Voltage (V)
Input/
+ - Signal name
Output
1
Ground Ground — — 0 – 1
(B)
Front power window motor When front RH switch in
2
Ground (passenger side) DOWN Output power window main switch Battery voltage
(GR)
signal is DOWN at operated.
JMKIA0070GB
JMKIA0070GB
It changes to condition before initialization and the following functions do not operate when switched to fail-
safe control. N
• Auto-up operation
• Anti-pinch function
O
Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe
control when malfunction is found in power window main switch or front power window motor (driver side).
ABKWA2385GB
PWC
ABKIA5401GB
ABKIA5402GB
PWC
ABKIA5403GB
ABKIA5404GB
PWC
ABKIA5405GB
ABKIA5406GB
OVERALL SEQUENCE
C
PWC
P
ALKIA1982GB
DETAILED FLOW
1. OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2. CONFIRM THE SYMPTOM
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3. IDENTIFY THE MALFUNCTIONING SYSTEM WITH SYMPTOM DIAGNOSIS
Use Symptom diagnosis from the symptom inspection result in step 2 and then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
>> GO TO 4.
4. PERFORM THE COMPONENT DIAGNOSIS OF THE OF THE APPLICABLE SYSTEM
Perform the diagnosis with Component diagnosis of the applicable system.
>> GO TO 5.
5. REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6. FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Are the malfunctions corrected?
YES >> Inspection End.
NO >> GO TO 3.
1.SYSTEM INITIALIZATION E
Perform system initialization. Refer to PWC-29, "Work Procedure".
>> GO TO 2. F
2.CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to PWC-30, "Work Procedure". G
>> END
H
PWC
When the power window main switch is replaced, the initialization is necessary for normal operation of power
window system.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure INFOID:0000000009757227
1.SYSTEM INITIALIZATION
Perform system initialization. Refer to PWC-29, "Work Procedure".
>> GO TO 2.
2.CHECK ANTI-PINCH FUNCTION
Check anti-pinch function. Refer to PWC-30, "Work Procedure".
>> END
If any of the following operations are performed, the initialization is necessary for normal operation of power B
window system.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by C
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly. D
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION: E
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function F
Work Procedure INFOID:0000000009757229
1.STEP 1 G
>> GO TO 2.
2.STEP 2 J
If any of the following operations are performed, the initialization is necessary for normal operation of anti-
pinch function.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure INFOID:0000000009757231
>> END
BCM
Ground Voltage
Connector Terminal J
88
M85 — Battery voltage
90
Is the inspection result normal? PWC
YES >> GO TO 3.
NO >> Repair harness or connector.
L
3.CHECK GROUND CIRCUIT
Check continuity between BCM connector M85 and ground.
M
BCM
Ground Continuity
Connector Terminal
M85 93 — Yes
N
BCM
Ground Continuity
Connector Terminal
M20 65 — Yes
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair harness or connector.
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Description INFOID:0000000009757234
D5 10
Ground Battery voltage
D11 18 F
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2. G
Main power window and door lock/unlock switch connector Terminal Continuity
Ground
D11 1 Yes
Is the inspection result normal?
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
LH) GO TO 5.
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
RH) GO TO 6.
YES >> Check main power window and door lock/unlock switch output signal (front power window switch
LH) GO TO 7.
YES >> Check main power window and door lock/unlock switch output signal (front power window switch
RH) GO TO 8.
NO >> Repair or replace the harness or connectors.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M85 or M20 and ground.
With Intelligent Key system
Terminals
Voltage
(+)
(–) (Approx.)
BCM connector Terminal
91
M85 Ground Battery voltage
92
Without Intelligent Key system
Terminals
Voltage
(+)
(–) (Approx.)
BCM connector Terminal
68
M20 Ground Battery voltage
69
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
NO >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key) or BCS-126,
"Removal and Installation" (without Intelligent Key).
5. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH LH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D5 and ground.
Terminal
(+) Window switch Voltage
(–) position (rear LH) (Approx.)
Main power window and door lock/
Terminal
unlock switch connector
UP Battery voltage
9
DOWN 0
D5 Ground
UP 0
8
DOWN Battery voltage
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
Terminal
(+) Window switch Voltage J
(–) position (front LH) (Approx.)
Main power window and door lock/
Terminal
unlock switch connector
UP Battery voltage
PWC
17
DOWN 0
D11 Ground
UP 0 L
19
DOWN Battery voltage
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident". M
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation". After that, refer to PWC-29, "Work Procedure".
8. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (FRONT N
POWER WINDOW SWITCH RH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON. O
3. Check voltage between main power window and door lock/unlock switch D5 and ground.
Terminal
(+) Window switch Voltage
(–) position (front RH) (Approx.)
Main power window and door
Terminal
lock/unlock switch connector
UP Battery voltage
16
DOWN 0
D5 Ground
UP 0
2
DOWN Battery voltage
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation". After that, refer to PWC-29, "Work Procedure".
POWER WINDOW MAIN SWITCH : Component Inspection INFOID:0000000009757237
Terminal Main power window and door lock/unlock switch condition Continuity
10 9 Rear LH
10 7 Rear RH UP
10 16 Front RH
8 9 Rear LH
6 7 Rear RH NEUTRAL
Yes
2 16 Front RH
10 8 Rear LH
10 6 Rear RH DOWN
10 2 Front RH
1 12 -
2. Check continuity between main power window and door lock/unlock switch D5 (power window lock
switch) (Lock operation).
Terminal Main power window and door lock/unlock switch condition Continuity
9 Rear LH
7 Rear RH UP
16 Front RH
8
Rear LH
9
7
1 Rear RH NEUTRAL No
6
2
Front RH
16
8 Rear LH
6 Rear RH DOWN
2 Front RH
3. Check continuity between main power window and door lock/unlock switch D5 (power window lock
switch) (Unlock operation).
Terminal Main power window and door lock/unlock switch condition Continuity A
9 Rear LH
7 Rear RH UP
16 Front RH
B
8
Rear LH
9 C
7
1 Rear RH NEUTRAL Yes
6
2 D
Front RH
16
8 Rear LH
E
6 Rear RH DOWN
2 Front RH
Is the inspection result normal? F
YES >> Main power window and door lock/unlock switch is OK.
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation". After that, refer to PWC-29, "Work Procedure". G
POWER WINDOW MAIN SWITCH : Special Repair Requirement INFOID:0000000009757238
Power Window And Door Lock/Unlock Switch RH Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT (POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH)
1. Turn ignition switch ON.
2. Check voltage between power window and door lock/unlock switch RH connector D104 and ground.
Terminal
(+) Voltage
(–) (Approx.)
Power window and door lock/unlock
Terminal
switch RH connector
D104 8 Ground Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM, power window and door lock/unlock switch RH, rear power window switch LH and rear
power window switch RH.
3. Check continuity between BCM connector M85 or M20 and power window and door lock/unlock switch
RH connector D104.
With Intelligent Key system
Power window and door lock/unlock
BCM connector Terminal Terminal Continuity
switch RH connector
M85 92 D104 8 Yes
Without Intelligent Key system
Power window and door lock/unlock
BCM connector Terminal Terminal Continuity
switch RH connector
M20 68 D104 8 Yes
4. Check continuity between BCM connector M85 or M20 and ground.
BCM
Continuity
Connector Terminal
Ground
M85 (with Intelligent Key system) 92
No
M20 (without Intelligent Key system) 68
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the harness or connectors.
3. CHECK HARNESS CONTINUITY (POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH)
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and power window and door lock/unlock
switch RH.
3. Check continuity between main power window and door lock/unlock switch connector D5 and power win-
dow and door lock/unlock switch RH connector D104.
Main power window and door Power window and door lock/
Terminal Terminal Continuity
lock/unlock switch connector unlock switch RH connector
2 11
D5 D104 Yes
16 12
4. Check continuity between main power window and door lock/unlock switch connector D5 and ground.
PWC
COMPONENT INSPECTION
1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH
L
Check power window and door lock/unlock switch RH D104.
Terminal
(+) Voltage
Condition
(–) (Approx.)
Rear power window
Terminal
switch connector
LH D203
6 Ground Ignition switch ON Battery voltage
RH D303
Is the inspection result normal?
YES >> GO TO 2 (Rear power window switch LH).
YES >> GO TO 3 (Rear power window switch RH).
NO >> GO TO 4.
2. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch and rear power window switch LH.
3. Check continuity between main power window and door lock/unlock switch connector D5 and rear power
window switch LH connector D203.
Main power window and door lock/ Rear power window switch
Terminal Terminal Continuity
unlock switch connector LH connector
8 7
D5 D203 Yes
9 4
4. Check continuity between main power window and door lock/unlock switch connector D5 and ground.
Main power window and door lock/ Rear power window switch
Terminal Terminal Continuity
unlock switch connector RH connector C
6 7
D5 D303 Yes
7 4
D
4. Check continuity between main power window and door lock/unlock switch connector D5 and ground.
BCM
Continuity M
Connector Terminal
Ground
M85 (with Intelligent Key system) 92
No
M20 (without Intelligent Key system) 68 N
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key) or BCS-126,
"Removal and Installation" (without Intelligent Key). O
NO >> Repair or replace harness or connectors.
5. CHECK REAR POWER WINDOW SWITCH
P
Check rear power window switch.
Refer to PWC-42, "REAR POWER WINDOW SWITCH : Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
NO >> Replace rear power window switch. Refer to PWC-72, "Removal and Installation".
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW SWITCH
Check rear power window switch.
F
Regarding Wiring Diagram information, refer to PWC-18, "Wiring Diagram".
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
1. Turn ignition switch OFF. H
2. Disconnect front power window motor LH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor LH connector D8 and ground.
I
Terminal
Main power window and
(+) Voltage
door lock/unlock switch con- J
(–) (Approx.)
Front power window motor dition
Terminal
LH connector
UP Battery voltage PWC
1
DOWN 0
D8 Ground
UP 0
3 L
DOWN Battery voltage
Is the inspection result normal?
YES >> GO TO 3. M
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF. N
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between main power window and door lock/unlock switch connector D11 and front
power window motor LH connector D8. O
Main power window and door lock/un-
Front power window motor LH
lock switch Terminal Terminal Continuity
connector
connector P
17 1
D11 D8 Yes
19 3
4. Check continuity between main power window and door lock/unlock switch connector D11 and ground.
COMPONENT INSPECTION
1.CHECK FRONT POWER WINDOW MOTOR LH
Check motor operation by connecting the battery voltage directly to power window motor D8.
Terminal
Motor condition
(+) (–)
1 3 UP
3 1 DOWN
Is the inspection result normal?
YES >> Front power window motor LH is OK.
NO >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation". After that,
refer to PWC-29, "Work Procedure".
DRIVER SIDE : Special Repair Requirement INFOID:0000000009757251
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
power window and door lock/unlock switch RH.
A
1. CHECK FRONT POWER WINDOW MOTOR RH CIRCUIT
Check front power window motor RH operation with main power window and door lock/unlock switch or power
window and door lock/unlock switch. B
Is the inspection result normal?
YES >> Front power window motor RH is OK.
NO >> Refer to PWC-45, "PASSENGER SIDE : Diagnosis Procedure". C
Terminal
(+) Front power window motor Voltage (V) H
(–) RH condition (Approx.)
Front power window motor RH
Terminal
connector
UP Battery voltage I
3
DOWN 0
D105 Ground
UP 0 J
1
DOWN Battery voltage
Is the inspection result normal?
YES >> GO TO 3. PWC
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY L
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D104 and front power
window motor RH connector D105. M
COMPONENT INSPECTION
1. CHECK FRONT POWER WINDOW MOTOR RH
Check motor operation by connecting the battery voltage directly to front power window motor RH D105.
Terminal
Motor condition
(+) (–)
3 1 UP
1 3 DOWN
Is the inspection result normal?
YES >> Power window motor is OK.
NO >> Replace front power window motor RH. Refer to GW-16, "Removal and Installation".
REAR LH
REAR LH : Description INFOID:0000000009757256
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
rear power window switch LH.
REAR LH : Component Function Check INFOID:0000000009757257
Terminal A
(+) Window Voltage
(–) condition (Approx.)
Rear power window motor LH
Terminal
connector B
UP Battery voltage
1
DOWN 0
D204 Ground C
UP 0
3
DOWN Battery voltage
Is the inspection result normal? D
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY E
N
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR LH
O
Check motor operation by connecting the battery voltage directly to rear power window motor LH D204.
Terminal
Motor condition P
(+) (–)
3 1 DOWN
1 3 UP
Is the inspection result normal?
YES >> Rear power window motor LH is OK.
NO >> Replace rear power window motor LH. Refer to GW-21, "Removal and Installation".
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
rear power window switch RH.
REAR RH : Component Function Check INFOID:0000000009757261
Terminal
(+) Rear power window Voltage
(–) switch RH condition (Approx.)
Rear power window motor RH
Terminal
connector
UP Battery voltage
1
DOWN 0
D304 Ground
UP 0
3
DOWN Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH.
3. Check continuity between rear power window switch RH connector D303 and rear power window motor
RH connector D304.
F
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR RH
Check motor operation by connecting the battery voltage directly to rear power window motor RH D304. G
Terminal
Motor condition
(+) (–) H
3 1 DOWN
1 3 UP
I
Is the inspection result normal?
YES >> Power window motor is OK.
NO >> Replace rear power window motor RH. Refer to GW-21, "Removal and Installation". J
PWC
Detects condition of the front power window motor LH operation and transmits to main power window and door
lock/unlock switch as pulse signal.
DRIVER SIDE : Component Function Check INFOID:0000000009757265
Terminals
(+)
Signal
Main power window and door lock/ (–) (Reference value)
unlock switch Terminal
connector
4
D5 Ground Refer to following signal
5
JMKIA5210GB
Terminal A
Voltage
(+)
(–) (Approx.)
Front power window motor LH connector Terminal
D8 2 Ground Battery voltage
B
Main power window and door lock/ Front power window motor LH
Terminal Terminal Continuity
unlock switch connector connector
F
D5 14 D8 2 Yes
4. Check continuity between main power window and door lock/unlock switch connector D5 and ground.
G
Main power window and door lock/unlock switch con-
Terminal Continuity
nector Ground
D5 14 No H
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-70, "Removal and Instal-
lation". After that, refer to PWC-29, "Work Procedure". I
NO >> Repair or replace harness or connectors.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF. J
2. Disconnect front power window motor LH.
3. Check continuity between front power window motor LH connector D8 and ground.
PWC
Front power window motor LH connector Terminal Continuity
Ground
D8 6 Yes
L
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
M
5. CHECK HARNESS CONTINUITY 2
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch connector D5 and front power N
window motor LH connector D8.
Main power window and door lock/un- Front power window motor LH
Terminal Terminal Continuity O
lock switch connector connector
D5 12 D8 6 Yes
Is the inspection result normal? P
YES >> Check main power window and door lock/unlock switch. Refer to PWC-36, "POWER WINDOW
MAIN SWITCH : Component Inspection".
NO >> Repair or replace the harness or connectors.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect main power window and door lock/unlock switch.
Main power window and door lock/unlock Front power window motor
Terminal Terminal Continuity
switch connector LH connector
4 5
D5 D8 Yes
5 4
3. Check continuity between main power window and door lock/unlock switch connector D5 and ground.
Door switch
Continuity
Connector Terminal
Front door switch LH B21
Ground
Front door switch RH B28
3 No
Rear door switch LH B26
Rear door switch RH B41
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-73, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK DOOR SWITCH
Refer to PWC-54, "WITH INTELLIGENT KEY : Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace malfunctioning door switch.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-39, "Intermittent Incident".
Door switch
Condition Continuity
Terminal
1.CHECK FUNCTION
With CONSULT D
Check door switches DOOR SW-DR, DOOR SW-AS, DOOR SW-RL, DOOR SW-RR in Data Monitor mode
with CONSULT.
E
Monitor item Condition
DOOR SW-DR
DOOR SW-AS F
CLOSE → OPEN: OFF → ON
DOOR SW-RL
DOOR SW-RR
G
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to PWC-55, "WITHOUT INTELLIGENT KEY : Diagnosis Procedure". H
WITHOUT INTELLIGENT KEY : Diagnosis Procedure INFOID:0000000009757273
I
Regarding Wiring Diagram information, refer to DLK-224, "Wiring Diagram".
J
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscilloscope. PWC
Terminals
(+) Voltage (V)
Door condition
(–) (Approx.)
BCM
Terminal
connector
OPEN 0
45 Front RH
CLOSE
PKIB4960J
7.0 - 8.0 V
OPEN 0
48 Rear RH
CLOSE
PKIB4960J
7.0 - 8.0 V
B57 Ground
OPEN 0
46 Front LH
CLOSE
PKIB4960J
7.0 - 8.0 V
OPEN 0
47 Rear LH
CLOSE
PKIB4960J
7.0 - 8.0 V
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and door switch connector.
Door switch A
BCM connector Terminal Terminal Continuity
connector
45 B28 (Front RH)
48 B41 (Rear RH) B
B57 3 Yes
46 B21 (Front LH)
47 B26 (Rear LH)
C
Ground circuit of main power window and door lock/unlock switch shuts off if power window lock switch of
main power window and door lock/unlock switch is operated. This inhibits all operation, except for the main
switch.
Component Function Check INFOID:0000000009757276
PWC
C
1.CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
Refer to PWC-37, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure". D
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts. E
2.CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE)
Check front power window motor (passenger side).
Refer to PWC-45, "PASSENGER SIDE : Diagnosis Procedure". F
Is the inspection result normal?
YES >> GO TO 3.
G
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH
• Replace power window main switch. H
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END I
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED
J
WHEN FRONT POWER WINDOW SWITCH (PASSENGER SIDE) IS OPERATED :
Diagnosis Procedure INFOID:0000000009757281
PWC
1.CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIR-
CUIT
Check front power window switch (passenger side) power supply and ground circuit. L
Refer to PWC-37, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 2. M
NO >> Repair or replace the malfunctioning parts.
2.CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
N
Check front power window switch (passenger side).
Refer to PWC-37, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal?
O
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH P
• Replace power window main switch.
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
Revision: October 2013 PWC-61 2014 Sentra NAM
FRONT PASSENGER SIDE POWER WINDOW DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
WHEN POWER WINDOW MAIN SWITCH IS OPERATED : Diagnosis Procedure
INFOID:0000000009757282
C
1.CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". D
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts. E
2.CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to PWC-46, "REAR LH : Diagnosis Procedure". F
Is the inspection result normal?
YES >> GO TO 3.
G
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH
• Replace power window main switch. H
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END I
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED
J
WHEN REAR POWER WINDOW SWITCH LH IS OPERATED : Diagnosis Procedure
INFOID:0000000009757284
1.CHECK REAR POWER WINDOW SWITCH LH POWER SUPPLY AND GROUND CIRCUIT PWC
Check rear power window switch LH power supply and ground circuit.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". L
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts. M
2.CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". N
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts. O
3.REPLACE POWER WINDOW MAIN SWITCH
• Replace power window main switch. P
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
C
1.CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". D
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts. E
2.CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to PWC-48, "REAR RH : Diagnosis Procedure". F
Is the inspection result normal?
YES >> GO TO 3.
G
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH
• Replace power window main switch. H
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END I
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED
J
WHEN REAR POWER WINDOW SWITCH RH IS OPERATED : Diagnosis Procedure
INFOID:0000000009757287
1.CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT PWC
Check rear power window switch RH power supply and ground circuit.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". L
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts. M
2.CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure". N
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts. O
3.REPLACE POWER WINDOW MAIN SWITCH
• Replace power window main switch. P
• Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
WHEN POWER WINDOW MAIN SWITCH IS OPERATED
PWC
PWC
REMOVAL
1. Release the pawls using a suitable tool and lift the main power window and door lock/unlock switch and
finisher as an assembly and remove.
2. Disconnect the harness connector from the main power window and door lock/unlock switch.
3. Release the four pawls (two on each side) using a suitable tool,
then separate the main power window and door lock/unlock
switch (1) from the main power window and door lock switch fin-
isher (2).
: Pawl
CAUTION:
Do not bend back the pawls on the switch finisher too far or
breakage may occur.
ALKIA2814ZZ
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
When the main power window and door lock/unlock switch is disconnected from the harness connector it is
necessary to perform the initialization procedure. Refer to PWC-29, "Work Procedure".
REMOVAL B
1. Release the pawls using a suitable tool and lift the power window and door lock/unlock switch RH and fin-
isher as an assembly and remove.
2. Disconnect the harness connector from the power window and door lock/unlock switch RH. C
3. Release the four pawls (two on each side) using a suitable tool,
then separate the main power window and door lock/unlock
switch RH (1) from the main power window and door lock switch D
RH finisher (2).
: Pawl
CAUTION: E
Do not bend back the pawls on the switch finisher too far or
breakage may occur.
F
ALKIA2816ZZ
INSTALLATION G
Installation is in the reverse order of removal.
PWC
REMOVAL
1. Release the pawls using a suitable tool and lift the rear power window switch and finisher as an assembly
and remove
2. Disconnect the harness connector from the rear power window switch.
3. Release the pawl (one on each side) using a suitable tool, then
separate the rear power window switch (1) from the rear power
switch finisher (2).
: Pawl
CAUTION:
Do not bend back the pawls on the switch finisher too far or
breakage may occur.
ALKIA2817ZZ
INSTALLATION
Installation is in the reverse order of removal.