Академический Документы
Профессиональный Документы
Культура Документы
PumpHouse
This worksheet calculates the required development length & lap splice length for deformed bars in
tension, as per ACI-350 clause 12.2.3 & 12.15
Parameter Input
Lap splices of deformed bars in tension shall be class B except that class A
splices are allowed when both (a) and (b) are met:
Horizontal reinforcement so placed that more than 12in. of fresh concrete is cast in the
member below the development length or splice: = 1.3. Otherwise = 1
Case A: For epoxy coated bars: if c < 3db or sclear < 6db then =1.5, otherwise 1.2
β1 if cover 3 db 1.5 1.2 β1 1.2
β2 if s clear 6 db 1.5 1.2 β2 1.5
βA max β1 β2 βA 1.5
β if UseCoatedBars = "yes" βA βB β 1.5
α β 1.95
γ if db 19mm 1.0 0.8 γ1
λ 1
Calculations
2
π dtr 1000mm 2
Atr Atr 392.699 mm
4 s tr
fy
fyt 1000mm
N ntr
2 s tr
mm
Atr fyt
k tr
1500 s tr ntr k tr 4.105 mm
Ktr k tr
db spacing
c b min cover c b 75 mm
2 2
cb Ktr
Tr
in in
Tr 3.164
db
in
but not greater than 2.5 Tr min ( Tr 2.5) Tr 2.5
Ras Al Khair Spicing Length
PumpHouse
Development length of bar in tension (straight bars) analytical formula ACI 350-06 Eq 12-1
fy
3 psi αβ γ λ
ld db => ld 1298 mm
40 fc Tr
psi
ld max ld 300mm
ld
ld 1298 mm => 51.9
db
Refer to reinforcement summary table of top slab. A comparison of the rebar required for strength
Vs rebar provided in drawings yields a MINIMUM ratio of 90%
rreb 1
splice_length if SpliceClass = "B" 1.3 ld ld rreb
splice_length 1687 mm
NOTE:
The design of the top slab is performed considering a durability factor (Sd) of 1.3 for all ULS
combinations and Sd=1.65 for the combinations that include thermal (temperature) actions that induce
pure tension is the section (e.g. contraction of the slab). The rational of the durability factor is to ensure
that stress in rebar in environmental structures are retained/capped at a low level at the ULS conditions
(since Sd is applicable to ULS design combinations). The inclusion of the Sd factor ensures that
stesses do not exceed a value of 24ksi, as stated in section 9.4 of ACI 350-06.
At the same time, the SLS checks have been perfomred considering a maximum stress in rebar of 0.4
fy e.g. 24ksi (refer to SLS calcs).
From the above, it can be easily concluded that rebar stresses in the structure in all conditions during
its lifetime will be well below the fy yield stress (60ksi) value that is taken into account to calculate the
anchorage length above.
Ras Al Khair Spicing Length
PumpHouse
fy
( min ( α β 1.7) λ)
ld_simplified psi db if db ( 19mm) s clear 2 db cover db
fc
25
psi
fy
( min ( α β 1.7) λ)
psi db if db ( 19mm) s clear 2 db cover db
fc
20
psi
fy
3 ( min ( α β 1.7) λ)
psi db if db 19mm s clear db cover db
fc
50
psi
fy
3 ( min ( α β 1.7) λ)
psi db otherwise
fc
40
psi
ld_simplified 2.163 m
Lap_length_simpl if SpliceClass = "B" 1.3 ld_simplified ld_simplified
Lap_length_simpl 2.812 m
Lap_lnegth_analyt splice_length
Lap_lnegth_analyt
0.6
Lap_length_simpl