Вы находитесь на странице: 1из 11

CETest ID: 177272 TarGATE’17 www.gateforum.

com

General Ability
Q. No. 1 –5 Carry One Mark Each

1. In the following question choose the word which best expresses the meaning of the given word.
DELINQUENT
(A) Accurate (B) Derelict (C) Amend (D) Mitigate

2. In the following question, read the whole sentence and select the appropriate word to complete
the sentence.
His ______ display of tears at work did not impress his new manager, who felt he should try to
control his emotions.
(A) maudlin (B) meritorious (C) plausible (D) precarious

3. In the following question, read the whole sentence and select the appropriate word to complete
the sentence.

Nandini found an overpriced furniture at the antique shop and tried to ______ with the
shopkeeper, but she __________ to lower the price.
(A) quibble, allowed (B) concur, despised
(C) comply, ascend (D) haggle, spurned

4. A means 'add to', B means 'multiply by', C means 'subtract from' and D means 'divide by' then 12
D2B13A9C5 = ___________.

5. Pipes P and Q can fill a tank in 5 and 6 hours respectively. Pipe R can empty it in 12
hours. If all three pipes are opened together, then the tank will be filled in ________.
60 42 50 40
(A) (B) (C) (D)
17 15 11 37

Q. No. 6 –10 Carry Two Marks Each.

6. The Board of Directors of the Lejon Etymological Museum imposed a 50-cent admission charge
in order to reduce the Museum's deficit. Attendance remained stable and there was no protest
from the public, so, six months later, the Museum announced that the admission price would go
up to $1.50.
It can be inferred that, in increasing the admission charge to $1.50, the Board of Directors
assumed that:
(A) People did not protest the initial charge because they felt it was necessary to keep the
Museum in operation.
(B) Since people did not protest the initial charge, they will also accept the raised price.
(C) Since $1.50 is three times the original charge, it is probable that attendance will drop as the
public protests the increase.

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

1
CETest ID: 177272 TarGATE’17 www.gateforum.com

(D) The increased revenue from admissions will enable the Museum to expand its operations.
7. In the question below three statements are given followed by three conclusions numbered I, II,
and III. You have to assume everything in the statement to be true, then consider the three
conclusions together and decide which of them logically follows beyond a reasonable doubt from
the information given in the statement.
Statements: Some books are chairs.
Some chairs are pens
All the pens are pencils.
Conclusions: I. Some pencils are chairs.
II. At least some pens are books.
III. No pen is book.
(A) Only conclusion I follows (B) Only conclusion II follows
(C) Only conclusion III follows (D) Conclusions I and III follows

8. The following table gives the percentage of marks obtained by seven students six
different subjects in an examination.

Student Maths Physics Chemistry Geography History Computer


Science
150 (120) (130) (100) (60) (40)
Arun 90 90 30 60 70 80
Maya 100 80 80 40 80 70
Samanya 90 70 60 70 90 70
Raghu 80 80 65 80 60 60
Sugun 80 85 65 95 50 90
Nikil 70 65 75 85 40 60
Prajay 65 50 35 77 80 80

In which subject is the overall percentage the best?


(A) Maths (B) Physics (C) Chemistry (D) History

9. The difference between simple and compound interests compounded annually on a


certain sum of money for 2 years at 4% per annum is Rs. 0.0016. The sum in (Rs) is ___.

10. Cost of raw material of a product increases by 50%, the manufacturing cost increases by
30% and the selling price of the product increases by 70%.The raw material and the
manufacturing cost ,originally, formed 40 and 60 of the total cost respectively. If the

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

2
CETest ID: 177272 TarGATE’17 www.gateforum.com

original profit was one-fifth the original manufacturing cost, find the approximation new
profit percentage.
(A) 68.9% (B) 89.5% (C) 37.97% (D) 45.89%

Civil Engineering
Q. No. 1 – 25 Carry One Mark Each

 sin α − cos α 0 
1. If A= cos α sin α 0  then the value of A −1 is ____________.
 0 0 1 

2. Five students have to stand in a row. The chance that two particular students stand side by
side is _______.

1 − sin x π
 π − 2x , x≠
2 π
3. If f (x) =  is continuous at x = then value of λ is________.
λ π 2
, x=
 2

4. For a random variable X, if V ( x ) = 6, then V ( 2x + 3) =


(A) 12 (B) 24 (C) 15 (D) 13

1
5. At t = 0, the inverse Laplace of the function equals __________.
( s + 1) ( s2 − 1)

6. The number of elastic constant for a completely anisotropic elastic material, which follows
Hook’s law, is _________.

7. A cable is suspended between two level supports across horizontal span of 60 m. If cable carries a
load of 5KN m along length of cable and if central sag is limited to one of span, the maximum
cable tension is _______KN.

8. A ball attached with a string of length l follows a vertical circular path with linear velocity
3gl at lower most position. The velocity of ball at position where the tension in the string is
zero and make angle ∝ with the vertical is
(A) gl [1 − 2sin ∝] (B) gl [1 − cos ∝]

(C) gl [1 − sin ∝] (D) gl [ cos ∝]

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

3
CETest ID: 177272 TarGATE’17 www.gateforum.com

9. An amount of Rs 4000/- is available in perpetuity in uniform series of income at the end of each
4-year period. Sinking fund factor @ 8 % pa for discrete compounding is 0.222. For the same
interest rate, the capitalized equivalent income is
(A) Rs 12,500 (B) Rs 11,100 (C) Rs 16,225 (D) Rs 13,485

10. A rectangular prestressed beam 200mm wide and 300mm deep is used over an effective span of
10m. The cable with zero eccentricity at the supports and linearly varying to 40 mm at the centre
carries an effective prestress force of 300KN. If load counteracts the bending effect of the
prestressing force, then the magnitude of the concentrated load ‘P’ located at the centre of span
(in kN), will be __________. (Neglect self weight of beam)

11. A circuler shaft of dia 150m is welded to a rigid plate by an external all round fillet load of size
10mm torque of 10N-m is applied to shaft then find maximm shear stress developed in weld
(A) 40.42 N mm 2 (B) 20.21N mm 2 (C) 4.042 N mm 2 (D) 2.021N mm 2

12. In power house, a circular penstock of 1.2m diameter is made out of 12mm thick plate, lapping of
10 mm size provided inside and outside of the cylinder as shown in fig. what factored internal
pressure can be alloned is penstock ? [ take fu of weld metal as 400MPa]____ N mm 2 .

13. A normally consolidated clay has a compression index = 0.20 . Initial void ratio of this clay layer
is 0.90 and thickness=3m. If the initial soil stress is10KN / m 2 , the value of stress up to which it
can be increased to make ultimate settlement of 2cm?
(A) 10.67KN / m 2 (B) 12.67KN / m 2 (C) 13.57KN / m 2 (D) 11.57KN / m 2

14. Soil is compacted at which one of the following when a higher compactive effort produces
highest increase in dry density?
(A) Saturation moisture content (B) Dry side of the OMC
(C) Wet side of OMC (D) Optimum moisture content

15. Consider a sliding surface AB in the figure below:

60° 10m

soil
10m C = 50 K N m 2
φ =10°
γ = 18 K N m 3

Normal effective pressure on sliding surface AB is 255 KN/m2


Downward tangential disturbing force along AB is 840 KN.
The factor of safety with respect to height is
(A) 1.846 (B) 1.264 (C) 1.341 (D) 1.628

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

4
CETest ID: 177272 TarGATE’17 www.gateforum.com

16. A plate test was conducted in sandy soil with plate of size 0.30m × 0.30m. The ultimate load per
unit area was found to be 2.0 kg cm 2 . The allowable load for a footing of
2m × 2m using FOS as 3 is _____________.
(A) 13.33kg cm 2 (B) 5.33kg cm 2 (C) 6.65kg cm 2 (D) 4.44 kg cm 2

17. A compound pipe line 2000m long is made up of pipe 0.3m diameter for 1000m, 0.5m diameter
for 500m and 0.2m diameter for the remaining length. The diameter of an equivalent pipe for the
same length is _________ m.
(A) 0.202 (B) 0 .156 (C) 0.462 (D) 0.251

18. A kite has an effective area of 0.40m2 and weighs 2.0N in a wind of 40kmph. String is inclined at
45o to horizontal and the drag on the kite is 11.9N. The lift coefficient is calculated as
( Take ρ=1.208 kg/m3 )
(A) 0.413 (B) 0.362 (C) 0.325 (D) 0.466

19. The water surface at a particular section of rivers during flood a was found to increase at rate of
11.2cm hr . The normal discharge for the rivers stage obtained from steady flow rating curve was
160 m3 Sec and slope of river is 1 3600 . Assuming, the velocity of flood wave as 2.0 m Sec , the
actual discharge is _________ m3/sec.

20. During a storm of 5 hr duration of intensity 20 mm/hr, the total observed runoff volume is
30mm3. If the area of catchment is 400 km2, then the average infiltration rate
is _________ mm/hr.

21. Consider the following graph between dissolved oxygen and duration:

X
Y
Dissolved oxygen
Z

D uration

The option showing correctly matched curve is _____________.

(A) X − Oxygen sag curve (B) X − Re oxygenation curve


Y − Re oxygenation curve Y − Deoxygenation curve
Z − Deoxygenation curve Z − Oxygen deficit curve

(C) X − Deoxygenation curve (D) X − Oxygen sag curve


Y − Re oxygenation curve Y − Deoxygenation curve
Z − Oxygen curve Z − Re oxygenation curve

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

5
CETest ID: 177272 TarGATE’17 www.gateforum.com

22. In a BOD test using 4% dilution of the sample DO values for the sample and dilution blank water
bottle after 5 days incubation at 20o C were given as 3.6 mg/l and 8.4 mg/l. DO originally present
in undiluted sample was 0.70mg/l. 5 days, 20o C BOD of the sample is ___________mg/l.

23. Descending gradient of 1 in 50 and meets an ascending gradient of 1 in 80 to form a valley curve.
Desing speed is 54 kmph. If allowable rate of change of acceleration is 0.54 m/s3, what will be the
length of valley curve to fullfill comfort condition_____m.

24. The following data pertains to the member of commercial vehicles per day for the design of a
flexible pavement far a national highway as per IRC 37-1984:

Type of commercial vehicle No.of vehicles per day Vehicle damage factor
Considering number of lanes
Two axle trucks 4000 4
Tandem axle trucks 600 5

Assuming a traffic growth factor of 8% per annum for both types of vehicles, The cumulative
number of standard axle load repetetions for a design life of 10 year is __________ Msa.

25. The reduced level of floor is 90.855m and staff reading on floor is 3.065m. The reading on staff
held upside down against the underside of the beam is 3.56m The height of Tee-beam above the
floor level is
(A) 5.825m (B) 6.625m (C) 7.285m (D) 5.265m

Q. No. 26 – 55 Carry Two Marks Each

1 2 3   b1 b2 b3 
26. If A =  4 5 6 & B =  b 4
  b5 b6  where b1 , b 2 ,b 3 , b 4 − − − b 9 are cofactors of the
7 8 0  b7 b8 b9 
elements 1,2,3,4,5,6,7,8,9,0 then B = __________.

− x2

27. The value of ∫ 0
e 32
dx = ___________.

(A) 2π (B) 2 2π (C) 4 2π (D) π


2

logx
28. The maximum value of is _______.
x
1 2
(A) e (B) 2e (C) (D)
e e

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

6
CETest ID: 177272 TarGATE’17 www.gateforum.com

29. If A, B, C, D are four non singular matrices such that ABCD = I, then
( B−1 ) =__________.
T

(A) CDA (B) ADC (C) CT DT A T (D) A T DT CT

dy
30. The error in the estimation of y (1.1) of the differential equation = 2xy with
dx
y(1) = 1 and using step size h=0.1 by Euler’s method is ___

2
31. If a pendulum swings of a circle connected with a string of length 150 cm during the
3
time interval T = 1sec. Then average speed and average velocity of pendulum during this
internal respectively are
3
(A) 3 m s, 2π m s (B) 2π m s, 1.5 3 m s
4
m m
(C) 2π m s,0.75 3 m s (D) 1.5 3 , 2π
s s

32. Two equal length link and a slider are arranged as a mechanism as shown in the figure.
The value of ‘ θ ’ to maintain equilibrium is ___________ degrees.

400N

400 400

θ  300N

33. A tube of aluminium of 40mm external diameter and 20mm internal diameter is
completely filled with a solid steel rod of 20mm diameter. The component bar is
subjected to an axial compressive force P.
Find the stress in aluminium tube when the stress in steel bar is 70 N / mm 2 .
Given : E=2 × 105 N / mm 2 ( steel )
E = 7 × 104 N / mm 2 ( aluminium )

(A) 20.2N / mm 2 (B) 24.5N / mm 2 (C) 26.2N / mm 2 (D) 28.2N / mm 2

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

7
CETest ID: 177272 TarGATE’17 www.gateforum.com

34. Principal stresses at a point are +200 MPa, -150 MPa and +100 MPa. If modified
modulus of elasticity is ratio of linear stress to actual strain in that direction, then the
modified modulus of elasticity of that material, having young’s modulus of elasticity is
200 GPa and Poisson’s ratio as 0.3 (In GPa), will be
(A) 175 (B) 180 (C) 186 (D) 194

35. A moving load as shown in figure crosses the simply supported beam of 16m span from
left to right. Maximum bending moment in the beam is
4KN 6KN 2KN

4m 2m

16 m

(Repart answer in KN-m)_______KN-m

36. In the portal frame shown below, what are the distribution factors for members BA and
BC respectively :

G
l
B
F C
2I I
l

2I 2I
2l
D
E A

l l

4 3 8 4 3 4 4 8
(A) , (B) , (C) , (D) ,
19 19 19 19 19 19 19 19

37. The three activities indicates are shown in sequence The possible alternatives for
individual duration (D) in days and corresponding cost of resource consumption in unit of
money per day respectively, are also indicated beside the activities over head cost are to
be added at 12 unit of money per day of duration The most optimal total cost including
overhead if all activities are completed in either 22 or 21 days.

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

8
CETest ID: 177272 TarGATE’17 www.gateforum.com

D R D R D R
5 5 10 10 8 9
4 7 8 13 7 11

(A) 453 units of cost (B) 460 units of cost


(C) 466 units of cost (D) 450 units of cost

38. The activity duration (days) and resource requirements are shown in the figure below:

A ( 4days) B( 6days )
Res ( 5units )
Res :6units
C(10 days )
( Res :4units )
D( 5days ) E ( 6days)
Res :2units
Res:( 8units )

The maximum resource required on particular day is _________.


(A) 16 units (B) 12 units (C) 19 units (D) 18 units

39. What is the radial moment at a distance x greater than radius of the circle form the centre
when simply supported slab carrying a total load w distributed on the circumference of a
concentric circle
w r 
2 2
R r 
(A) M r =  2log e −   + 2 −   
8π  x R  R  

w 
2 2
R  r  r
(B) M r =  2log e +   + 2 +   
8π  x R R 

w R  r  r 
2 2

(C) M r =  2log e −   +   
8π  x  R   x  

w 
2 2
R r  r
(D) M r =  2log e +   +   
8π  x R R 

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

9
CETest ID: 177272 TarGATE’17 www.gateforum.com

40. A simply supported rectangular Beam (300×600mm) having effective depth of 550mm is
reinforced with (4-20 φ +2-16 φ ) Bars. (fy=415Nmm2. fck = 20N/mm2)
The moment of resistance of the section is ______________.
(A) 200KNm (B) 250KNm (C) 150KNm (D) 300KNm

41. Number of bolts required to design lap joint between two plates, 80 as to transmit a
factored load of 70 KN using M 16 bolts using of grade 4.6 and grade 410 plates (pitch
p = 40, edge distance e = 30)
(A) 2 (B) 3 (C) 4 (D) 5

42. At given location, 8m thick saturated clay (natural water content=30%, G s = 2.70 ) is
underlain by sand. The sand layer is under artesian pressure equivalent to a 3m water
head. It is proposed to make an excavation in clay. The depth up to which excavation can
be made before the bottom heaves;
(A) 3.6423m (B) 4.7235m (C) 6.4527m (D) 5.6214m

43. The dry unit weight γ d of a soil having 15% moisture content is 18.5KN / m3 . The
submerged unit weight assuming G s = 2.7 is ___________.
(A) 9.7468KN / m3 (B) 11.6478KN / m3 (C) 10.2468KN / m3 (D) 21.6478KN / m3

3y
44. The velocity distribution over a flat plate is given by u = − y 2 where u is the velocity in
4
m/s at a distance y(m) above the plate and µ = 0.084NS / m 2 . The shear stress at location
0.3m above the plate is K times the shear stress at a location 0.2m above the plate.
The value of K is ______________.
(A) 3/2 (B) 9/4 (C) 3/7 (D) 7/3

45. The ultimate bearing capacity of square footing of 1.5m size at a depth of 1.5m in a pure
clay with confined strength of 150 KN m 2 φ = 0° and γ =17 KN m3 is______ KN m 2

46. In a steady laminar flow of a given discharge through a circular tube of dia D, the head
loss is proportional to ____________.
(A) ( D )
−1/2
(B) D −5 (C) D −2 (D) D −4

47. Water flows out of a tank through a small orifice on a vertical wall under a constant head
of 2 meters. The orifice diameter is 2cm. The water jet issuing out of the orifice drops
downward due to the action of gravity. It is seen that the vertical fall is 10cm for a
horizontal displacement of 85cm from the vena-contracta, then

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

10
CETest ID: 177272 TarGATE’17 www.gateforum.com

The co-efficient of velocity would be __________.


(A) 0.967 (B) 0.953 (C) 0.928 (D) 0.982

48. What is the BOD mass loading in Kg/day for a wastewater treatment plant having design
flow rate of 60m3/min and long term daily average BOD concentration is 200g/m3.
(A) 17280kg/day (B) 1728000kg/day (C) 1728kg/day (D) 172800kg/day

49. A 3m wide grit chamber is to be constructed to handle 1.5m3/s of sewage praving a


detention time of 3 minutes what should be the length of such channel and depth to width
ratio is 2.
(A) 10m (B) 12m (C) 15m (D) None

50. In a high volume sampler the initial weight of filter used was 4.2356 gms & final weight
after high volume sampler was run for 12 hours at 1.05m3/min was 4.3868. What is the
concentration of particulate matter?
Note : HVS is an instrument used to sample aerosols It has a very high flow rate and can
run for a very long time
(A) 100µg / m3 (B) 150 µg / m3 (C) 200 µg / m3 (D) 250 µg / m3

51. Speed density relationship for a particular road was found to be, u = 58.24 – 28 k, where
u is speed in kmph and K is density of vehicle per km. The minimum time headway in
second is _______.

52. A vehicle moving at 54 kmph was stopped by applying brake and the length of skid mark
was 20.4m. If the average skid resistance of the pavement surface is known to be 0.60.
Determine the brake efficiency of the test vehicle
(A) 91.4% (B) 93.6% (C) 95.2% (D) 96.8%

53. Vertical ascending gradient grade +4% meets an a descending gradient of 4% to form a
summit curve Desing speed is 80 kmph. Perception braking time is 2.5 seconds. Friction
cofficient between road surface and vehicle is 0.35. Find length of summit curve _____m

54. A sailor standing on deck of ship just sees the top of light house. The top of light house is
30 m above sea level and height of sailor’s eye is 5m above sea level. The distance of
sailor from the light house is;
(A) 21.16km (B) 8.64km (C) 29.80km (D) 12.52km

55. A long a slope the distance between two points A & B is measured as 505m The
horizontal distance between A and B when difference of elevation of A and B is 65m
considering correction for slope is
(A) 500.7993m (B) 480.7993m (C) 500.8169m (D) 480.8169m

ICP–Intensive Classroom Program eGATE-Live Internet Based Classes DLP TarGATE-All India Test Series
Leaders in GATE Preparation 65+ Centers across India
© All rights reserved by Gateforum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission.

11

Вам также может понравиться