Академический Документы
Профессиональный Документы
Культура Документы
APPLICATION OF COMPUTER
Definition of Computer
Computer is mainly used for data processing. It performs arithmetical and logical
operations on the input data in between the input and output which is called processing.
The processing methods are provided by the users by logical instructions known as
program.
To many people , the word computer suggests “ computation” and the word means
‘math”, which scares some people, but this connection is misleading. Computer are not
calculators, although you can turn a computer into a calculator, the simplest definition, a
computer is an electronic device-a flexible machine that can manipulate data. Many of
these manipulations have nothing to do with math.
A computer is programmable that is, what the computer does depends on the program
the computer is using . A computer’s hardware- the machine and its components is
designed to be as flexible as possible . By using computer programs, called software, you
transform this flexible hardware into a tool for purpose.
2
No matter which program a computer is using, the machine itself performs only four
basic operation. The most widely accepted definition of the computer includes the
following operations .
Input A computer accepts data that is provided by means of an input device, such as a
keyboard.
Storage A computer stores the results of processing operation for future use.
This definition is often referred to as the IPOS cycle. The four steps of the IPOS cycle
–input, processing, output, storage do not have to occur in a rigid I-P-O-S sequence
under the direction of the program, the computer uses the steps of this process when
needed and so often as needed.
Characteristics of computer
Microsec
Nannosec
Picosec
Computer can work much faster than human beings. Today’s personal computers run at a
clock speed in the hundreds of megahertz.
2. Automation:- For doing every work, computer requires or needs a human user. Once
a program is in the computer’ memory, the individual instructions are then transferred,
one after the other to the control unit for exculpation. It simply means that the computers
are not intelligent as human beings. They always need to be programmed by a human
being.
5. Diligence:- Being a machine, a computer does not suffer from the human traits of
tiredness and lack of concentration . Diligence is a property by virtue of which a
computer can work continuously without getting tired & without loosing concentration.
6. Memory & Storage:- Memory is that area in computer where the storage of data
takes place. The stored data can be retrieved back easily in fraction of seconds. The
information is stored in the forms of files, but on discs and tapes. This helps in easy and
speedy retrieval of information. This is known as electronic storage system.
CLASSIFICATION OF COMPUTERS
1. Digital : Digital computer is a computer that stores data as discrete numbers or digits(
i.e0 and 1) and processes them in distinct steps e.g Digital clock. Thus , a digital
computer uses symbolic representations of its variables. A digital can easily store and
manipulate numbers, letters, images, sounds or graphical information represented by a
symbolic code.
3. Hybrid : A hybrid computer is one that combines both digital and analog technology.
Mainframes
Mainframes are the most widely used type of computer in large businesses. IBM still
holds an estimated two-thirds of the mainframe market. A mainframe computer is
usually composed of several computers in addition to mainframe, or host processor.
Mainframe computer systems are powerful enough to support several hundred users
simultaneously at remote terminals. The capability to process many programs
concurrently for multiple users is known as multiprogramming
4
Supercomputers
Supercomputers are the largest, fastest, most powerful and most expensive computers
made. These are rarely used for input/output –intensive processing, such as accounting
or record keeping operations. This type of computer has been developed for scientific
applications usually involving complex arithmetic and mathematical operations. One
such use in weather forecasting e.g. PARAM 1000 ( developed by India & Japan in1998 )
Mini Computers : These perform multi- tasking and allow many terminals to be
connected mini computer to each other and main frames has popularized them among
larger businesses. This is being challenged by the development in the microcomputers
under a range and practice of sharing resources of microcomputers under a network.
Minicomputers are still recognized as being able to process large amount of data.
Microcomputers
There are many types of microcomputer platforms with varying capabilities. The most
common type of microcomputer is a desktop computer, which is a non portable personal
computer that fits on top of a desk. Most microcomputers enable the user to switch
between tasks. This capability is known as multitasking. Laptop computers are portable
computers. Portable computers came the age with the advent of notebook computers.
LIMITATIONS
Computers may pose a threat to personal privacy, because firms can so easily accumulate
a detail picture of an individual’s buying habits.
A computer is an electronic digital machine that takes data and performs a task upon an
instruction in a predetermined manner and provides the output.
The computer is an managerial tool capable of processing large quantities of data very
rapidly and accurately. It can perform arithmetic and logical operations and can dispense
results in a variety of formats. Computer can repeat programmed instructions almost
endlessly without error, can hold large quantities of information in storage and can be
used to stimulate decision modeling situations.
Components of a Computer:
Computer mainly has the Central Processing Unit (CPU) comprising of three parts, they
are Memory, (ii) Control Unit and (iii) Arithmetic and logical Unit (ALU)
The Memory Unit: is a group of chips known as (Random Access Memory). RAM chips
their main function is to store information and instructions that are in use by the CPU.
This unit is also termed as primary storage or working storage area.
The memory is measured in BYTES, each BYTES is basically made of eight Binary
Digits (BITS).
The Control Unit : is the main processes chip, which has the capacity to understand the
instruction, fed into the memory Unit. It makes the other units performs the tasks, by
assigning the work to the connected devices and parts according to the instruction fed to
it. The capacity of control unit is measured as speed in Hz (Hertz)
The Arithmetic and Logical Unit: is a part of the CPU, which as its name goes performs
arithmetical operations and logical operations.
The data received by the memory unit is assigned to this unit by the control unit along
with the instruction as to what ALU has to do with the data, whether to logically
evaluate or arithmetically. Once the activity is finished the output again upon the
instruction by the CU is kept in the memory unit.
The CPU is connected to different input and output devices. It’s ability to perform on
different devices using different software like windows has earned the multi-media
computers.
6
GENERATION OF COMPUTER
The First Generation: It consisted of more of mechanical devices and vacuum tubes. It
was as big as a foot ball field, using several miles of wire. It worked very slowing had to
be switched off frequently due to the heat it used to generate. Its maintenance was very
difficult due to its mammoth like structure.
The Second Generation: This used transistor as main components. This had reduced it’s
size to a huge hall. It didn’t lose much of the negative characterstics of its earlier version.
Low maintenance and more advanced in terms of aritemetic logic unit and control unit.
Examples of II Generation :- PDP-1, developed by DEC, It was the first minicomputer.
NCR 304 ( National Cash Register)
The Third Generation : This had integrated Circuit (ICs) as its Components. This
further reduce the size a grate deal. The advent of micro-electronics technology started
the method of integrating large number of circuit elements in small surface of silicon
known as ‘chips’. The new invention of integrated circuit( ICS) defines the third
generation of computers.
The CPU design was made simple and a technique called microprogramming was
introduced.
The operating systems were facilitated with the efficient method of sharing the facilities
or resources such as processor and memory space, automatically.
7
This refined the ICs to Large Scale Integrated Circuits (LSIC) and Very Large Scale
Integrated Circuits (VLSIC ). This generation is still holding the reins is very popular
and has been part of almost everybody’s life one way or other on the other in the
present day. This has made a possible the personal computers, Laptop computers and
palm top computers.
Examples of IV Generation :-
These are some of the limitations of fourth generations. unlike the human brain a
computer cannot think on its own, cannot learn by experience cannot handle real time
situations. It is a programimg language that uses instructions to make it perform a task.
Primary Storage/ Memory: As mentioned earlier, the memory in the CPU is the
primary storage. It keeps the data and instructions that are being used by the CPU and the
processed output from the ALU. This memory is the highly volatile memory, it looses all
that it has stored in itself if power is off for even a fraction of a second. All the
information is processed and stored in chips.
Both reading and writing can take place, therefore it is also known as Read-write
memory. It holds information and data temporarily.
The word “random” refers to the fact that any piece of data can be returned quickly and
in constant time, regardless of its physical location and whether or not it is related to the
previous data.
ROM: It stands for read Only Memory, because only reading can be done; writing is not
allowed.
It is non volatile i.e the data will not get lost, if the power is not turned off.
It contains the instructions for booting the computer and loading operating system for the
hard into RAM.
Computer’s main memory is the primary storage. Additional storage facilities are needed
to store information and retrieve it as and when it is required. Such storage facilities as
referred as secondary storage media. It is used to store data permanently.
Optical disk
Magnetic disk ( Hard disk & floppy disk )
Magnetic tapes
9
OPTICAL DISK
1. An optical is an electronic data storage medium that can be written to and read
using a low powered laser beam.
2. An optical disk is impressed with a series of spiral pits in a flat surface.
3. Optical disk can store more data at lower cost therefore, they are used as a
complement to magnetic storage media.
MAGNETIC DISK
It is a thin circular metal plate coated on both the sides with a magnetic material. It is
similar to a gramophone record. It is of two types :-
Floppy disk : It is made of flexible plastic which is coated with magnetic oxide.
Flexible disk is enclosed within a square plastic referred as cartridge, which gives
handling protection to the disk surface. It is random access storage medium. Data is
stored in tracks and sectors. Each sector holds 512 Bytes worth of data.
Hard disk: It is the most popular medium for secondary storage. It is made up of a
metal plate coat on both side with a magnetic material. A disk pack consists of a no. of
these disks ( 3 or more) mounted above half an inch apart from each other on a central
shaft. Each disk consists of no. of invisible concentric circle called tracks. The number of
tracks and sectors on a disk is known as its ‘format’. The hard disk direct access storage
medium.
MAGNETIC TAPE:
1. Magnetic tapes are similar to cassette tapes in being accessed only serially.
2. It is very popular medium for storage of voluminous amount of processing data.
3. Each record on a tape is separated by blank spaces called the inter record gaps.
4. it is reusable and erasable.
Input devices are those devices are those devices through which data can be fed into the
computer. In the other words, input devices accepts data from outside world and converts
the data in binary forms and finally sends it to the computer for further processing.
Examples of Input Devices
Keyboard OBCR
MICR Scanner
Digitizer Microphone
Webcam Mouse
10
Output devices are those devices through output or processed information can be
obtained . In other words, output devices accepts data in binary from the computer and
converts the coded data to human acceptable form and finally outputs the converted result
to the outside world. Examples of Output devices are :
SOFTWARE CONCEPTS
Software is a set of programs that governs and controls the operation of a computer
system. Without software , hardware can not perform on its own. So, this is the software,
which make the hardware run. Software can be classified as
System Software
Application Software
1.System Software : System software encompasses those programs that are used to
manage the resources of computer at low level. System Software is generally required
loading, supervising, controlling, and execution of computer programs. It is further
classified as:
a. Operating System
b. Language processors
The Hardware
The Operating System
The application Program routines ( compiler, linkers, utility programs etc )
11
The user
Where hardware provides physical resources, the application program routines tell the the
ways in which these resources are used to solve the various problems of the user and the
operating system controls and coordinates the use of the hardware among various user.
Language processors
The computer does not understand any language other its own machine language which is
based on two digit ( 0 and 1). But programs can not write their programs in machine
language. They prefer to write their programs in one of the High Level Languages
because it is much easier to write programs in such languages when compared to the
machine language. Therefore, it becomes necessary to process a HLL programs so as to
make it understandable to the computer. And the system program which programs this
job of translator is called the language processor. There are three types of language
processors.
(ii ) Interpreter : This language processor converts the program written in high Level
Language into machine language. It converts and executes a program line by line. If it
finds any error in any line, it reports it at the same time. Program execution does not
proceed until the error is rectified. Interpreter is very much useful as it reports the errors
at the same time. But, when all errors are removed and there is no works remains for
interpreter even then it does not leave the place in memory. Therefore, it is always
present in the memory whether it is required or not.
(iii ) Compiler : this language processor also converts HLL program into machine
language. Here the conversion process works differently. It converts the whole HLL
programs in one time and reports all the errors of the program with their respective line
numbers. When all the errors are removed, the program is recompiled and after that the
compiler is required no more in the memory. Therefore , if we combine interpreter and
compiler, it gives the combination for HLL program translation . When all the errors are
removed the program can be compiled. This process is executed to remove the language
translator from the memory.
APPLICATION SOFTWARE
An application software is the set of necessary programs to carry out operations for a
specified application. This type of software is meant for one specific application.
For example, the software that can prepare results for a school cannot perform railway
reservation functions.
12
The programmers write these programs to enable us to perform a specific task on the
computer such as financial accounting , inventory control, result preparation , railway
reservation , engineering design , etc. Application software can further be subdivided into
two categories.
Customized Application Software
This type of software is developed keeping in mind the general requirements for carrying
out a specific job. Because it fulfills the general requirements, many users can use it at
one time.
Low Level Language or machine Language Or binary Language : the language that
the microprocessor can read and interpret is called low level Language or machine
Language. It is called binary language because low level language code consists of
binary bits . i.e 0 and 1. These ‘0’ and ‘1’ represents the state of the pulse in the circuit.
If there is pulse in the circuit then it represented as “1’ and the absence of pulse is
indicated by ‘0’ .
Therefore, this language is very difficult to understand. But the main advantage of this
language is that it is faster in execution as the computer directly starts executing it.
High Level Language : A high level language does not require the programmer to have a
detailed knowledge of computers. A high level language contains statements that are like
English and mathematics. One statement from the instructions set of high level language
is capable to perform an operation which requires many machine instructions. Therefore,
it is much easier to write a program using a high level language than using either
assembly or machine language. It is easily understandable by human beings because high
level language code consists of English language like statements e.g COBAL, PASCAL,
BASIC, FORTRAN, JAVA, C, C++ etc.
Assembly Language : The languages that that used Mnemonic operations codes and
symbolic rotations were called assembly languages. Assembly languages are closely
related to machine languages and the internal architecture of the computer system on
which they are used. These languages are called low level languages .
The program in assembly language cannot be executed unless it is converted into
machine language. A program written to convert assembly language instruction to
machine language is called an assembler. Converting the assembly language program to
machine language programs is called assembling the program.
14
OPERATING SYSTEM
a. formatting disk
b. displaying the content of a disk
c. Checking a disk for reading and writing
d Determining the space remaining on a disk
5. Making a back up copy of the back up contents of a hard disk and restoring the
contents from a back up copy.
4. File Management : All operating systems include support for a variety of file
systems. A file system is a method for storing and organizing computer files and data
they contain to make it easy to find and access them.
Networking : Most current operating systems are capable of using the TCP/ IP
networking protocols. This means the one system can appear on a network of the other
and share resources such as files, printers and scanners using either wired or wireless
connections.
15
It is an acronym that stands for Disk Operating System. It is written by BILL GATES
and PAUL ALLEN in 1980s. It is a single user and unitasking system. The early version
of DOS is known as QDOS ( Quick & Dirty DOS) Written by Tim Paterson . DOS
prepared by Microsoft Company is known as MS- DOS. It’s current version is MS-DOS
8.0 . Similarly, DOS developed by IBM (International Business Machine ) is called PC-
DOS.
Internal Commands
The commands which are present in the COMMAND.COM file are called internal
command. Some important internal commands of DOS are as follows:
Internal Commands
External Commands
INTRODUCTION TO WINDIWS
A computer has many peripheral devices attached with it like mouse, keyboard, printer ,
scanner, modem etc. These are either input devices. OS does the allocation and release of
these devices to and from jobs on user requisition. Thus operating system acts as an
interface between these peripherals and the user. Interface can be of two types-
CUI
GUI
CUI GUI
It is unitasking It is multitasking
Windows are most popular GUI based operating system that was developed by
Microsoft Company of America. Windows are very user friendly and easy to use . It has
folders rather directories in DOS.
Difference between Window & windows: A window refers to a rectangular area in which
a program / a file or message is displayed. On the other hand windows refers to
Operating system.
1. Folder : Folder are special files that can hold multiple documents.
2. Sub-folder : It stands for sub-directory or other folder.
3. Object : It refers to shortcuts, programs or file
4. Navigation : This term is used for transversal in a directory
5. Icons : Icons represent the program or folders loaded into your computers
6. Desktop : It is the working area of the windows displayed in your computer.
7 Taskbar: The taskbar is the horizontal bar along the bottom of the desktop.
8 Pointer : A pointer is the arrow we use to choose things on screen .
9 Titlebar : It is horizontal bar displayed at the top of every program of window
10 Scrollbar : It is gray rectangle with small black arrows on both end.
11 Menubar : A menu bar is an onscreen display that lists available categories of
commands. It is located at the top of the program window.
12 File : A file is a collection of information , with a unique name stored in your
computer or on a removable disk.
My Computer: My computer is an icon that represents all the drives on your system. To
open a particular drive, either double click on it or write click on it and then choose open
or explore option.
Control panel : It is used to view or manipulate basic system settings such as display
settings, adding and removing hardware and changing accessibility option etc.
Window Explorer : Window explorer is the software program that best lets we manage
our computer’s files. It represents our computer as one big filling cabinet.
18
COMPUTER NETWORK
Today modern world requires a fast communication channel to move data frequently
from one place to another, the concept of networking has been introduced. In
networking, the computers in the different parts of the world are interconnected to share
data and information with each other.
Networking
Networking refers to an art of arranging computers in a network.
According to Andrews and Mcfredries “ Networking is a means of connecting computers
together so that can share resources, such as files and peripherals (printers, modems, CD-
ROM, drives etc) and services. It involves both hardware and software.’’
TYPES OF NETWORKS
There are three types of networks are widely used on the basis of geographical area and
transmission .
LAN (Local Area Network) : A network in which all nodes are connected with network
cable and which occupies a relatively small geographical area. For example; a building,
office, or department, or a home. It is restricted to the 10 km in size.
MAN (Metropolitan Area Network) : It is larger in size and its maximum limit upto
100 km. It is a bigger version of LAN and almost uses a similar technology. It links
computers of nearby corporate offices or various offices in the same city. A MAN can
support both data and voice. A local cable television network is a good example of
MAN.
WAN (Wide Area Network) A WAN is larger than MAN. It covers a large geographical
area, often a country or a continent. It contains a collection of machines intended for
running application program. In WAN, computers are connected with each other with
various telephone lines and satellites. Internet is the most important example of WAN.
19
COMMUNICATION CHANNELS
We connect two or more work stations by using cables. Communication channels are the
connecting cables being used in the network. There are three main type of cables that are
used as a communication channel between different workstations . These are as follows :
Twisted Pair Cable is the most common form of wiring in the data communication
applications. It is the basis for most of the internet telephone wiring. It is made of two
identical wires wrapped together in a twisted form. Both wires have the same impedance
to ground to make it a balance medium.
This feature helps to lower the cables, susceptibility to noise from neighboring cable or
external sources. The main advantage of this medium is that it is capable of carrying a
signal over long distances with the usages of repeaters. It is an adequate medium for
two speed applications where the distances between computers are small.
2. Coaxial Cables
It consists of a solid wire core surrounded by one or more foils or wires shields, each
separated from the other by some kind of plastic insulator. The inner core carries the
signal and shield provides the ground. It is used for television signals. The data
transmission characteristics of coaxial cables are quite better than those of twisted pairs.
It consists of less need for repeaters.
Optical fiber cable consists of thin strands of glass or glass like material . the data to be
transmitted are modulated onto the tight beam using frequency modulation technique.
And the signal can then be picked up at the receiving end by pin field effect transistor
demodulated. The installation of optical fibre cables is little difficult as these cables are
quite fragile and may need special shielding to make them strong for an office
environment. The main advantages of optical fibre over other media are their complete
immunity to noise, their high speed and low attenuation.
MODEM
As we know that we can convert data from digital to analog form and from analog to
digital form. The device which is used to convert digital data into analog form and vise
versa, is called a Modem. The analog signal are transferred through the telephone lines
and then converted into digital form by Modem. Therefore, modem performs the job of a
Modulator and Demodulator. The main use of a modem is that it allows higher speed pf
transmission on a given analog line and it reduces the effects of noise and distortion.
20
LAN CARDS
Lan card is an electronic card which is installed in the CPU of the central computer. If the
terminal connected with it have their own processor, then in that case each terminal
requires a separate Lan Cards installed in the computers are further connected with
cables.
REPEATER
Repeater is used to regenerate data and voice signals. Repeater reads the incoming signals
and amplifies them and transmits them to another segment of the of the network.
For example, Ethernet is a nine port repeater that is used to connect thin wires from
digital network to other cables.
Amplifying repeaters : They simply amplify the entire signal. They have the
disadvantage that as well as amplifying the data signal , they also amplify and existing
noise or interface as well.
Signal Generating Repeaters: This type of repeater “reads” the signal and then creates
a(stronger) duplicate of the data signal before sending on it.
Example: Used on baseband networks such as Ethernet. This networks can only transmit
one (digital) signal at a time. Data is represented by the on or off state of signals.
HUB
It is a network device where the information flow is accumulated and then distributed to
various groups. Hubs are basically signal splitters- they take the signals received through
one port and distribute them among the other ports hubs are powered devices. They may
include LED’s which can monitor power, active connections, traffic and collisions.
Types of Hubs
Passive Hubs
Active Hubs
Intelligent Hubs
Network Interface Card (NIC) : It is a circuit board, plugged into one of the expansion
slots of the work station and server.
The server and workstation should have the same type of NIC. NICs are usually
reserved for servers.
21
* They create the physical connection between the node and the rest of the network
* Their firmware is responsible for breaking data down into packets when transmitting
data and resembling the packets when receiving data.
NETWORK TOPOLOGIES
Kinds of Topologies
STAR TOPOLOGY: In Star Topology, all the terminals are directly connected to
central computer. This topology is used in most existing information networks involving
data processing or voice communication. The main advantage of star topology is that it is
very easy to add and remove any terminal without disturbing the network. If any terminal
fails, it can be easily disconnected without harming the work. The disadvantage of this
topology is that all activities are controlled by the server. Therefore, server is heavily
burdened. Each terminal is connected to the centre. So a larger quantity of cable is
required in this topology.
22
BUS TOPOLOGY : All the terminals are connected one after the another in a straight
line. This topology is also known as linear topology. The server can receive as well as
send the messages. A very short cable is required in this topology because there is a
single common data path connecting all terminals. It is comparatively cheaper and easy
to in stall. The main disadvantage of this topology is that it is very difficult to detect
fault and its isolation. If more than one terminal are taking part in communication, they
increase the burden on bus cable and the last terminal will take more time than the other
terminals for receiving and sending data.
RING TOPOLOGY : In this server and all the terminals are arranged in a circle and
connected with each other with cables in such a way a closed loop is formed. . This
topology is also called a loop. All nodes are transmitters and receivers. Data are
transmitted in one direction around the ring i.e. a node can expect transmission from a
node before it and the node itself can send transmission to other nodes. The amount of
cable required is generally less than for a star topology. The main disadvantage of this is,
if failure of one computer in the ring can affect the entire work. Difficult to or remove
node in a ring i.e each additional node involves system disruption and reduces
performances.
It uses some ‘‘ traffic control’’ mechanism that determines when to allow traffic to
travel up and down the branches of a tree. Allow easier trouble shooting.
The disadvantage of this is if there is disruption or error in any one branch of a tree , then
the whole network goes down. This ensure that there is only one path from one node to
any other node in the tree.
23
IP – Internet Protocol
-*-