Академический Документы
Профессиональный Документы
Культура Документы
Isolated Footing 1
2.04 m
1.3 m 1.75 m
0.45 m
Elevation
X 1.7 m
0.5 m
3.4 m
0.5 m
1.7 m
3.4 m
Plan
Input Values
Footing Geomtery
Calculate
Design Type :
Dimension
Footing Thickness (Ft) : 450.00 mm
Footing Length - X (Fl) : 3400.00 mm
Footing Width - Z (Fw) : 3400.00 mm
Eccentricity along X (Oxd) : 0.00 mm
Eccentricity along Z (Ozd) : 0.00 mm
Column Dimensions
Pedestal
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 2 of 12
Design Parameters
Soil Properties
Global Settings
Top Reinforcement Option : Calculate only when foundation is subjected to uplift forces
Concrete Design Option : Net Pressure(Gross Pressure - Self Weight Pressure)
Top Reinforcement Factor : 1.00
------------------------------------------------------
Design Calculations
Footing Size
Load Combinations
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 3 of 12
Moments are about the center of footing / pile cap (does not include moments caused by lateral loads)
2
Area from initial length and width, Ao = Lo X W o = 11.56 m
2
Min. area required from bearing pressure, Amin = 6.50 m
Note: Amin is an initial estimation considering self-weight, axial load and moment against factored bearing capacity.
Pressures at 4 Corners
Please note that pressures values displayed in tables below are calculated after dividing by soil bearing factor
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 4 of 12
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure will be set to zero and the pressure
will be redistributed to remaining corners.
Pressure at
Pressure at top Pressure at top bottom right Pressure at
Load Case / left corner right corner corner bottom left corner
Combination (kN/m2) (kN/m2) (kN/m2) (kN/m2)
Stability Check
2.04 m OTM
Load
Along X- Along Z- Required About X- About Z- Required
Case Resultant
Direction Direction FOS Direction Direction FOS
No.
Critical Load Case And The Governing Factor Of Safety For Overturning And Sliding - X Direction
Critical Load Case And The Governing Factor Of Safety For Overturning And Sliding - Z Direction
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 5 of 12
= 0.29m
Shear Calculation
X 1.7 m
Z
0.19 m
1.7 m
Plan
Total Footing Depth, D = 0.45m
Calculated Effective Depth, d = D - Ccover - 1 * db = 0.38 m
For rectangular column, = Bcol / Dcol = 1.00
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 6 of 12
X 1.7 m
Z 1.07 m
1.7 m 1.07 m
Plan
From ACI Cl.11.2.1.1, Vc = = 1285.73 kN
Check that 0.75 X Vc > Vux where Vux is the shear force for the critical load cases at a distance d from the face of the column caused by bending about the X axis.
X 1.7 m
1.06 m 1.06 m
1.7 m
Plan
From ACI Cl.11.2.1.1, Vc = = 1340.44 kN
Check that 0.75 X Vc > Vuz where Vuz is the shear force for the critical load cases at a distance d from the face of the column caused by bending about the Z axis.
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 7 of 12
30 - ϕ16
Calculate the flexural reinforcement along the X direction of the footing. Find the area of steel required, A, as per Section 3.8 of Reinforced Concrete Design (5th ed.) by
Salmon and Wang (Ref. 1)
The strength values of steel and concrete used in the formulae are in ksi
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 8 of 12
Because the number of bars is rounded up, make sure new reinforcement ratio < ρmax
Total reinforcement area, As_total = Nbar X (Area of one bar) = 6031.92 mm2
d= D - Ccover - 0.5 X (dia. of one bar) = 0.39 m
30 - ϕ16
Calculate the flexural reinforcement along the Z direction of the footing. Find the area of steel required, A, as per Section 3.8 of Reinforced Concrete Design (5th ed.) by
Salmon and Wang (Ref. 1)
The strength values of steel and concrete used in the formulae are in ksi
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 9 of 12
Because the number of bars is rounded up, make sure new reinforcement ratio < ρmax
Total reinforcement area, As_total = Nbar X (Area of one bar) = 6031.92 mm2
d= D - Ccover - 1.5 X (dia. of one bar) = 0.38 m
Pedestal Design
Pedestal Reinforcement Arrangement : 4 Faces
Shear Capacities
ϕVcX = 150.68 kN
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 10 of 12
(ϕVcX ref eqn ACI 318-11 Eqn 11.4 and Clause no 11.2.1.2)
ϕVsX = 98.96 kN
(ϕVsX ref eqn ACI 318-11 Eqn 11.15 and Clause No 11.4.7.2)
ϕVcZ = 150.79 kN
ϕVsZ = 98.96 kN
(ϕVsZ ref eqn ACI 318-11 Eqn 11.15 and Clause No 11.4.7.2)
Note- Actual stirrup provided is dependent upon design requirement and bar binding and positioning. So Stirrup provided in detail drawing may vary from designed stirrup
requirements.
1000
Factored Moment: 12.8
0 Factored Axial Load: 29.69
0 90 180 270 360 450 549.166377
540
Tension Control Zone
Moment - X [kNm]
Axial Capacity
Note: Factored pedestal design loads (inclusive of Φ = 0.00 based on ACI 318 Chapter 9)
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 11 of 12
Cc = = 833.16 kN
Mc = = 184.95 kNm
as
= -159026.64 kN/m2
= 0.0021
as
= 0.00 kN/m2
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/... 30/11/2017
Page 12 of 12
30/11/2017
X 1.7 m
2.04 m
Z
file:///C:/Users/Public/Documents/STAAD%20Foundation%20Advanced/Examples/...
0.5 m 1.3 m 1.75 m
3.4 m
0.5 m
1.7 m
3.4 m
0.45 m
Plan
TOP N/A
L B D AstX(T) AstZ(T) AstX(B) AstZ(B)
Foundation
1.7 m