Академический Документы
Профессиональный Документы
Культура Документы
1.0 Introduction
Before developing a deep familiarity with the various characteristics of amplifiers, it’s
common to spend a fair amount of time flipping back and forth through your notes and
textbook, in search of various formulas. To save you some trouble, here are many of the
relevant equations in one place. Because this set of notes is not intended to be a textbook
on network theory, only the barest sketches of derivations are usually provided. That said,
there should still be enough that you could reconstruct intermediate steps if needed.
Part of what distinguishes an experienced analog designer from others is the ability to
apply the simplest approximation that captures the phenomena of interest. Throughout,
recognize that many of the equations in this handout simplify considerably if you ignore
various factors (e.g. body effect, channel-length modulation, DIBL, etc.). In some cases,
we offer those simplifications. In others, they are left for you to finish. In all cases, pause
and consider when it may be acceptable to neglect certain of these phenomena, and how
that selective and conscious neglect simplifies the equations.
Throughout this handout, we use the following model for the transistor and load/source
resistances:
Cgd
RG Cgs Cdb RL
gm vgs gmb vbs r0
Csb RS
As you can see, we are implicitly assuming that the bulk terminal is tied to an incremental
ground.
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 1 of 9
Handout #11: EE214 Fall 2002
consequently not truly infinite. However, it still remains high enough for most purposes
that infinity is a useful approximation.
vgs = –i t RS ; (1)
So, at last, the resistance looking into the drain (and therefore not including RL), is
Multiplication of the total resistance at the drain by the effective transconductance will
give us the gain. To find the effective transconductance, short the drain to ground (incre-
mentally speaking), and measure the ratio of short-circuit output current to input voltage.
v gs = v in – i out RS ; (5)
v bs = – i out R S ; (6)
R R
i out = g m vgx + g mbv bs – i out ------S = g m( vin – i out R S) + g mb ( – i out RS )– i out -----S- ; (7)
r0 r0
i gm gm
gmeff = ---out
----- = ------------------------------------------------------- = ------------------------------------------------------ , (8)
v in RS 1 + ( g m + gmb + g0 )RS
1 + ( g m + g mb )RS + ------
r0
gm
A v = – gmeff ( r out || R L) = – ------------------------------------------------------ ( [ RS + r 0 + ( gm + g mb)r 0 RS ] || R L) (9)
1 + ( g m + gmb + g 0 )R S
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 2 of 9
Handout #11: EE214 Fall 2002
gm RL R S + r 0 + ( g m + g mb ) r0 R S
Av = – ------------------------------------------------------ ⋅ -------------------------------------------------------------------------- . (10)
1 + ( g m + g mb + g 0 )R S R S + r 0 + ( g m + g mb ) r0 R S + RL
After a little more work, the equation’s complexity reduces further, leading to a quite rea-
sonable expression:
gm RL
Av = – ------------------------------------------------------------------------------ . (11)
1 + ( g m + g mb )RS + g 0 ( RL + RS )
The reader should verify that this expression reduces to the expected approximations
when the body effect may be neglected, when there is no source degeneration, etc.
v gs = – vtest . (12)
With transconductance gmtot disabled, we compute one contribution to the test current:
v test
i t1 = ----------------- . (13)
r 0 + RL
Next, disable (short out) the test voltage source, taking care not to zero out gmtot, and com-
pute the other contributions to the test current. The current from the transconductance is
added to the current flowing through r0 .
v test r0 + R L r0 + R L
--------- = -------------------------- = ----------------------------------------- . (16)
it 1 + g mtot r 0 1 + ( g m + gmb )r 0
Note that, if RL << r0, and if the transistor’s “intrinsic voltage gain” gmr 0 is much greater
than unity, then the resistance looking into the source is approximately
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 3 of 9
Handout #11: EE214 Fall 2002
1
r in ≈ -------------------------- . (17)
( g m + gmb )
If you desire the total resistance between the source node and ground, simply compute the
parallel combination of rin and RS .
This resistance is precisely the same as the output resistance of the degenerated common-
source amplifier:
If we drive the source terminal directly with a voltage source, then RS = 0, and the equa-
tion for the resistance looking into the drain collapses to simply r0. That remains a reason-
ably good approximation as long as RS is small compared with r0, and (gm + gmb )RS is
small compared with unity.
v gs = – v i n ; (19)
v bs = v gs ; (20)
v in
i out = –g mtot v gx + ------ = v in ( gmtot + g0 ) ⇒ g meff = gmtot + g0 = ( g m + g mb + g 0) . (21)
r0
where we have used the fact that, in this first computation, we are driving the source
directly with a voltage source. The total drain resistance is thus just r0 ||RL, and the gain in
Eqn.22 is therefore that from the source to drain, as stated.
The voltage divider formed at the input must be taken into account to complete the calcu-
lation of the overall gain:
r in
Av = A v0 ⋅ ------------------ . (23)
r i n + RS
So,
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 4 of 9
Handout #11: EE214 Fall 2002
r 0 + RL
-----------------------------------------
1 + ( gm + g mb)r 0
A v = ( gm + g mb + g0 ) ( r 0 || RL ) ⋅ ------------------------------------------------------ , (24)
r 0 + RL
----------------------------------------- + RS
1 + ( g m + g mb )r 0
r 0 + RL
Av = ( gm + g mb + g 0) ( r0 || RL ) ⋅ -------------------------------------------------------------------------- , (25)
r0 + R L + R S + ( g m + gmb )r 0 RS
( g m + g mb + g 0 )R L
A v = ------------------------------------------------------------------------------ . (26)
1 + g 0 ( R L + R S ) + ( gm + gmb )R S
As expected, the gain expression collapses to more familiar forms when body effect is
neglected, the source resistance RS is zero, and if the transistor’s output conductance is
zero, etc. The reader should verify these statements independently.
r0 + R L r0 + R L
r out = -------------------------- = ----------------------------------------- . (27)
1 + gmtot r0 1 + ( gm + gmb )r 0
In most source followers, RL is chosen very small compared with r0 . In such cases, the
output resistance simplifies to:
r0
r out ≈ ----------------------------------------- . (28)
1 + ( g m + gmb )r 0
If, in addition, the transistor’s intrinsic voltage gain is high, then the unity factor in the
denominator can be neglected, simplifying the output resistance expression even further:
1
r out ≈ --------------------- . (29)
gm + gmb
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 5 of 9
Handout #11: EE214 Fall 2002
Again, compute an effective transconductance, and multiply by the output resistance. That
output resistance needs to include any external loading that might appear in parallel with
the resistance seen when looking into the transistor’s source.
v gs = vin ; (30)
v bs = v gs ; (31)
(for output resistance only; vbs = 0 for effective transconductance calculations). So,
R
i out = gm v in – i out ------L ; (32)
r0
i gm
g meff = ---out
----- = ---------------- . (33)
vin RL
1 + ------
r0
gm r 0 + RL
A v0 = gmeff( rout || R S ) = ---------------- ⋅ ----------------------------------------- || R (34)
RL 1 + ( g m + g mb )r0 S
1 + ------
r0
g m r 0 RS
A v0 = ------------------------------------------------------------------------------- . (35)
( gm + gmb )r 0 RS + ( r 0 + RL + RS )
g mR S 1
Av0 = ------------------------------------------------------------------------------ = -------------------------------------------------------------------- , (36)
( g m + g mb )RS + 1 + g 0 ( RL + R S ) ( g mb + g 0 ) ( 1 + g0 RL )
1 + ------------------------- + --------------------------
gm g mR S
from which it is perhaps somewhat easier to see that the voltage gain can only approach
unity, as we would expect from a source follower.
As usual, the reader should verify that the exact equation simplifies to the numerous
known approximations in the case where body effect is zero, transistor g0 may be
neglected, RL is zero, etc.
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 6 of 9
Handout #11: EE214 Fall 2002
Using a current source in a hybrid model, we find that the effective resistance may be
stated in a simple, universal, mnemonic form:
where rleft is the resistance seen between the capacitor’s left terminal and ground, rright is
that seen between the right terminal and ground, and gmf is the effective transconductance,
defined as the ratio of short-circuit output current to input voltage.
where we have recognized the product of effective transconductance and rright as (minus)
the voltage gain between the two terminals of the capacitor. From this form of the equa-
tion, we can see directly the effect of voltage gain between the capacitor’s terminals, a
phenomenon first explained by John M. Miller of the National Bureau of Standards, in
1918.
gm
R G + r out ||R L + ------------------------------------------------------ ( r ||R ) R , (39)
1 + ( g m + g mb + g 0 )R S out L G
where
The expression for the effective resistance simplifies considerably in the case of a com-
mon-gate connection, where RG is often zero (or very small). In that case, Eqn.40 is all
you need.
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 7 of 9
Handout #11: EE214 Fall 2002
resistance facing cgd . So, the expression for the resistance is somewhat complicated only
for the case of the common-source amplifier.
Here, the same basic two-port model applies, but now the model parameters have to be
chosen to reflect the fact that the capacitor in question connects between the gate and
source terminals. That is, the amplifier under consideration has its input at the gate, and
provides an output at the source. If we call RG. the resistance to the left, the resistance to
the right is simply the total output resistance of a source-follower (i.e., the resistance look-
ing into the source terminal, in parallel with any external RS). Similarly, the effective
transconductance is also merely that of a source-follower. So, we have actually derived all
of the pieces already. We just need to put them together:
r0 + R L gm r 0 + RL
r eq = RG + ----------------------------------------- ||R – ---------------- RG ----------------------------------------- ||R , (41)
1 + ( g m + gmb )r 0 S
RL 1 + ( g m + g mb ) r0 S
1 + ------
r0
RS
r eq = RG + -------------------------------------------------------------------------- [ ( r 0 + R L ) – gm r 0 RG] . (42)
r 0 + R L + R S + ( g m + g mb )r 0 RS
After some crunching, we finally get something that does look simpler:
RG ( r 0 + RL + R S + gmb r 0 R S ) + RS ( r 0 + RL)
req = -------------------------------------------------------------------------------------------------------- . (43)
r 0 + RL + RS + ( g m + gmb )r 0 RS
RG + RS + g mbRG RS + g 0 ( R GR L + R GR S + RS RL )
r eq = ----------------------------------------------------------------------------------------------------------------------- . (44)
1 + ( g m + gmb ) RS + g 0 ( R L + R S )
Note that, in the limit of no body effect and infinite r 0, the equivalent resistance facing cgs
indeed simplifies to a result we’ve seen before:
RG + RS
req ≈ ---------------------- . (45)
1 + gm RS
In the general case, this resistance is just the resistance looking into the drain of a transis-
tor, in parallel with any additional resistance connected to that drain (call that extra resis-
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 8 of 9
Handout #11: EE214 Fall 2002
tance RL to be consistent with our notation so far). We’ve already found the resistance
looking into the drain:
So, just place that value in parallel with any RL that happens to be present.
Similarly, this resistance is just that looking into the source of a transistor, in parallel with
any other resistance connected to it (we’ve been calling it RS). Thus, the source-follower
output resistance equation is what we need here:
r0 + R L
r out = ----------------------------------------- . (47)
1 + ( g m + gmb )r 0
Just compute the parallel combination of rout and RS to get the final answer.
©2002 Thomas H. Lee, rev. December 4, 2002; All rights reserved Page 9 of 9