Академический Документы
Профессиональный Документы
Культура Документы
Outline feature
OCP8162A Is an integrated 500V MOSFET Precision non-isolated led Constant integrated 500V power MOSFET
current driver chips, operating in a continuous current critical mode, support full voltage input In working without auxiliary winding current critical mode
AC 85V ~ 265V . detection and low power operating current (typical value: 130uA)
Chip SOP8 Package, the internal integration 500V Switch, using CS Foot set current, OCP8162A
Internal operating current is very small (approximately 130uA) , No auxiliary winding and a stand by AC85V ~ 264V The full input voltage range without
power supply monitoring, requires minimal external components both excellent output current loop compensation
precision, system cost and size savings. ± 5% The batch consistency
3% Line regulation
OCP8162A It combines a precision current sampling circuit, such that led 2% Load regulation
Output current accuracy ± 5% Within; achieve excellent line voltage regulation, linear rate led Open circuit protection
adjustment 3% Or less. OCP8162A Working inductance current critical mode, and does not led Short circuit
vary with output current led Change in operating voltage changes, to achieve excellent load protection primary side
regulation, load regulation 2% Or less, while achieving efficiency 90% the above. overcurrent detection
detection, led Open and short circuit protection, CS Open circuit protection, undervoltage application
lockout and overtemperature protection features to ensure that the entire system is safe and
AC / DC LED Drive signal and
reliable operation in harsh working environments.
decorative applications led light
OCP8162A Use of environmentally friendly materials SOP-8L Package, the
led candle light
operating temperature range of - 40 Degree to 85 Degrees between.
led Other bulb led illumination
Pin definitions
Pin Description
V CC voltage - 0.3 to 24 V
Note 1 : Refers to the maximum limit is beyond the scope of work, it may damage the device. Note 2 : The maximum temperature rise will reduce the power consumption, which is the T JMAX, θ JA, And the
ambient temperature T A The decision. The maximum allowable power consumption P DMAX = ( T JMAX - T A) / θ JA
85 ~ 265VAC ≤ 10
P led Output Power W
220VAC ± 15% ≤ 20
voltage
Current sampling
Working current
Over-temperature protection
Driver stage
Effciency (%)
Effciency (%)
6,065,707,580,859,095,100
175mA, 50V OUT 6,065,707,580,859,095,100
VIN = 110VAC VIN
170mA, 40V OUT 55
55 = 220VAC
170mA, 20V OUT
50 50
effectiveness VS The output voltage led Electric current VS The output voltage
160,170,180,190,200
= 220VAC = 220VAC
020406080100 140
20 25 30 35 40 45 50 20 25 30 35 40 45 50
160,170,180,190,200 160,170,180,190,200
175mA, 50V OUT
150
170mA, 40V OUT 150 VIN = 110VAC VIN
170mA, 20V OUT = 220VAC
140
140
85105125145165 185,205,225,245,265
- 40 --20 0 25 50 85
Input Voltage (V) LED Current Temperature ( ℃)
13.8 8.8 9
13.6
8.6
13.4
VUVLO (V)
8.4
VCC_TH (V)
13.2
8.2
13
12.8
12.6 7.8 8
12.4 7.6
- 40 --20 0 25 50 85 - 40 --20 0 25 50 85
Temperature ( ℃) Temperature ( ℃)
Minimum demagnetization time vs. Input voltage Minimum demagnetization time vs. temperature
Min DemagnetizationToff Vs. Input Voltage LED Open Protection Toff Vs. Temperature
10.0 10.0
9.0 9.0
8.0 8.0
LED Open Protection Toff (uS)
Min Demagnetization Toff (uS)
7.0 7.0
6.0 6.0
5.0 5.0
4.0 4.0
3.0 3.0
2.0 2.0
1.0 1.0
VIN = 265VAC
0.0 0.0
250
225
is
401,402,403,404,405
200
396,397,398,399,400
0,255,075,100,125,150,175
395
100
Ta = 25 ℃
0,102,030,405,060,708,090
(CH1 = V CC, CH2 = V SW) (CH1 = V CC, CH2 = V SW, CH3 = V CS)
Application Information
OCP8162A Is an integrated 500V MOSFET Precision non-isolated led Constant current driver chip, working in the current critical continuous mode, full support
Voltage input AC85V ~ 265V . OCP8162A use SOP8 Package, the internal integration 500V Switch, using CS Foot set current, OCP8162A
Internal operating current is very small (approximately 130uA) , No auxiliary winding and a power supply monitoring, requires minimal external components both excellent output precision constant current section
OCP8162A It combines a precision current sampling circuit, such that led Output current accuracy of ± 3% Within; achieve excellent line voltage regulation,
Linear adjustment rate 3% Or less. OCP8162A Working inductance current critical mode, and does not vary with output current led Changes in operating voltage changes, real
Now excellent load regulation, load regulation 2% Or less, while achieving efficiency 90% the above.
OCP8162A Have the best protection features, including chip led Detecting a short circuit, short-circuit signal Once the chip will enter the lower operating frequency limit
System output power. Protection chips include primary current overcurrent detection, led Open and short circuit protection, CS Open circuit protection, undervoltage lockout and overtemperature protection functi
1. start up
Before you start, the chip requires only 200uA Starting current, power supply VCC Voltage rises to the starting voltage 14V ( A typical value), the chip started. in case VCC
Voltage higher than 15.5V when, VCC Voltage terminal is built in a Zener clamp 15.5V .
By Chip CS The internal voltage terminal 400mV Comparing the threshold voltage of the transformer primary side peak current setting I PKP, when CS Internal detection voltage reaches
pkRI
= )
(400 mA (1)
CS
CS The output of the comparator comprises a 450nS The leading edge blanking time. led Output current is calculated as:
one
twenty
led
* = II pk = 2400 mA )
(R (2)
* CS
OCP8162A In the current critical work mode, when the built-in MOS When the tube is turned on, the current flowing through the inductor starts to rise from zero, the conduction time is:
* ILPK
t ON
= (3)
V -IN V LED
among them L As inductance; I PK For the inductor peak current; V IN Line voltage is rectified; V led Output led Voltage.
When the built-in MOS When the tube is closed, the current flowing through the inductor decreases from the peak value, the current dropped to zero when the inductor, to the internal circuit again
* ILPK
t OFF
= (4)
V led
1f led
* ( -IN VVV
LED
)
= = (5)
+ ttOFF
ON
V IN * L* I PK
led
* ( -IN VVV
LED
)
L = (6)
V IN * F* I PK
In theory, the formula 3 As can be seen with the input line voltage increases, t ON In the reduction, however, t OFF It did not change, so working with radio frequency
Increased pressure is increasing . So when designing the operating frequency, the operating frequency of the lowest minimum when the input line voltage, the maximum time work in the input line voltage
OCP8162A Integration minimum demagnetization time (typical 6.0uS) And the maximum demagnetization time ( 500uS) From equation 4 As can be seen, if the inductance is too small, then
t OFF To less than the minimum demagnetization time, the system enters a hiccup mode at this time, no normal output, the current from the design value. Meanwhile, if the inductance is too large, that
What t OFF The maximum becomes larger than the demagnetization time, this time the system enters the inductor current continuous mode, led The lamp current on the values deviate from the original design.
4. Protective function
OCP8162A Integrated protection features include over-temperature protection, led Lamp open / short circuit protection, CS Foot open / short circuit protection, transformer primary overcurrent
Care, VCC Undervoltage protection. When the chip temperature exceeds 150˚C , The chip enters the over-temperature protection, energy transfer is stopped until the temperature drops to 125˚C the following
When the output led When open, if there is no internal protection circuit, the output voltage will be gradually increased until the output capacitor damage. In order to protect the output capacitor being
Damage, minimum demagnetization time-chip detection, when detecting the minimum demagnetization time when the internal circuit power down pin, when energy transfer is stopped, the core
The electrical sheet automatic restart, to make the system work hiccup mode.
When the output led Short circuit, due to the slow demagnetization ( V LED = 0 , t OFF Increasing trend is infinite, t OFF The internal circuit is clamped at the maximum time demagnetization 500uS ),
In order to prevent the inductor current overshoot higher chip operates at lower frequencies in this case 2.0KHz State, can fully guarantee the demagnetization inductance, low power consumption. Short-circuit-l
After elimination of state, the output voltage returns to normal, the chip automatically enters the normal operating mode.
When the circuit detects CS When the pin is sampled resistor opens, the system operates in a lower frequency 2.0KHz status.
5. PCB design
(2) Current sampling resistor power ground as short as possible, and the other to the ground separately BULK The terminal of the capacitor.
(3) Large area to minimize the current loop, to reduce the EMI radiation.
(4) increase SW Copper area of the foot to improve the heat dissipation system.
Ordering Information
OCP8162AXXX
model Package Packing temperature range Environmental rating of the base material
13-in reel
OCP8162ASAD SOP-8L - 40 ~ 85 ℃ Green Cu
2500pcs / reel
Marking Information
Package Information
SOP-8L
Dimensions In Inches
Symbol Dimensions In Millimeters
Min. Max. Min. Max.
Packaging Information
Package Type Carrier Width (W) Pitch (P) Reel Size (D) Packing Minimum