Академический Документы
Профессиональный Документы
Культура Документы
1
LEGEND LEGEND-150 PIW Polyester/Polyester S&Z Twist Premium Carcass (EE250)
NUMBER OF PLIES
BREAK TENSILE ( LB./PIW) 3000
2
4500
3
6000
4
7500
5
LEGEND— 80 PIW Polyester/Polyester S&Z Twist Premium Carcass (EE 100) Recommended Load Support
NUMBER OF PLIES 2 3 4 5 6 MATERIAL WEIGHT LB./FT.3 0-40 41-80 81-120 121-180 181-240
BREAK TENSILE ( LB./PIW) 1600 2400 3200 4000 4800 DEGREE OF TROUGH 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° Behind the
OPERATING TENSILE ( LB./PIW) BELT SPECIFICATION
2/160 36 36 30 30
MAXIMUM BELT WIDTH IN INCHES
30 24 24 24 18 18 NR NR NR NR NR
S&Z Twist
MEDIUM DUTY @ 10:1 SF 160 240 320 400 480
3/240 48 48 42 42 42 42 42 36 36 30 30 24 24 NR NR
ELEVATOR @ 10:1 SF* 140 200 275 340 400
4/320 60 60 54 54 54 48 48 48 42 42 42 36 36 36 30
SKIM GAUGE (in.)
• Polyester warp yields great 0.050 0.050 0.030 0.030 0.030 5/400 72 60 54 60 60 54 54 54 48 54 48 42 48 42 36
CARCASS GAUGE ( ± .010 in.) 0.092 0.168 0.188 0.242 0.296 6/480 72 66 60 72 66 60 66 60 54 60 54 48 54 48 42
strength with minimal stretch MINIMUM PULLEY DIAMETER 2/220 42 42 36 36 36 30 30 30 24 24 24 18 NR NR NR Most belts in the Legend line
3/330 60 54 54 54 48 48 42 42 42 36 36 36 30 30 30
81-100% RATED TENSION 8 12 19 24 30
• Polyester fill provides good 4/440 72 66 60 60 60 60 54 54 54 48 48 42 42 42 36
feature S&Z Twist, a unique
61-100% RATED TENSION 5 10 15 19 24 5/550 72 72 66 72 72 66 66 60 54 60 54 48 54 54 48
lateral stiffness and increased load UP TO 60% RATED TENSION 3 8 10 15 18 6/660 84 84 72 84 84 72 72 60 54 72 60 54 66 60 54
support * Legg Co. does not recommend the use of poly/poly textiles in elevator belt applications if a poly/nylon is available 2/300 48 48 48 42 42 42 36 36 36 30 30 24 NR NR NR warp yarn design that redu-
3/450 60 60 60 54 54 54 48 48 48 42 42 42 NR NR NR
4/600 72 66 66 66 60 60 60 54 54 54 48 48 48 48 48
• A ll-polyester construction is 5/750 84 78 78 72 72 66 66 60 60 60 54 54 54 54 54 ces the natural tendency for
superior for fabrication involving hot
vulcanization a belt to track to one side.
Recommended Troughability
LEGEND — 110 PIW Polyester/Polyester S&Z Twist Premium Carcass (EE 200)
• Unique S&Z twist offers superior MINIMUM BELT WIDTH IN INCHES Easy tracking helps increase
NUMBER OF PLIES 2 3 4 5 6
tracking BREAK TENSILE ( LB./PIW) 2200 3300 4400 5500 6600
BELT SPECIFICATION 2/160 3/240 4/320 5/400 6/480
20° Idler 14 18 24 30 36
OPERATING TENSILE ( LB./PIW) 35° Idler 18 24 30 36 42
efficiency, so this innovative
• Manufactured using quality MEDIUM DUTY @ 10:1 SF 220 330 440 550 660 45° Idler 22 28 36 42 48
compounds with high elongation ELEVATOR @ 10:1 SF* 190 280 375 470 560 BELT SPECIFICATION 2/220 3/330 4/440 5/550 6/660 design more than pays for
and high adhesion properties SKIM GAUGE (in.) 0.050 0.050 0.030 0.030 0.030 20° Idler 16 18 24 30 36
35° Idler 20 24 30 36 42
CARCASS GAUGE ( ± .010 in.) 0.125 0.212 0.238 0.304 0.370
45° Idler 24 30 36 42 48
itself over time.
• Available in 80 lb., 110 lb. and MINIMUM PULLEY DIAMETER
BELT SPECIFICATION 2/300 3/450 4/600 5/750
81-100% RATED TENSION 16 20 24 30 37
150 lb. rated fabrics 20° Idler 18 24 30 36
61-100% RATED TENSION 14 18 20 24 30 35° Idler 24 30 36 36
UP TO 60% RATED TENSION 12 14 18 18 24 45° Idler 30 36 42 42
* Legg Co. does not recommend the use of poly/poly textiles in elevator belt applications if a poly/nylon is available
24 3
LEGEND
POLYESTER WARP • NYLON FILL • PL AIN WEAVE • S&Z T WIST
LEGEND — 125 PIW Polyester/Nylon S&Z Twist Premium Carcass (EP 220)
NUMBER OF PLIES 2 3 4 5 6
BREAK TENSILE ( LB./PIW) 2500 3750 5000 6250 7500
OPERATING TENSILE ( LB./PIW)
HEAVY DUTY @ 10:1 SF 250 375 500 625 750 Recommended Load Support
ELEVATOR @ 10:1 SF 215 320 425 530 640 MATERIAL WEIGHT LB./FT.3 0-40 41-80 81-120 121-180 181-240
SKIM GAUGE (in.) 0.050 0.050 0.030 0.030 0.030 DEGREE OF TROUGH 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
CARCASS GAUGE ( ± .010 in.) 0.132 0.221 0.250 0.319 0.388 BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
MINIMUM PULLEY DIAMETER 2/250 48 48 42 42 42 36 36 36 30 30 30 NR 24 NR NR
81-100% RATED TENSION 16 20 25 30 36 3/375 60 60 60 54 54 54 48 48 48 42 42 42 36 36 30
61-80% RATED TENSION 14 18 22 25 30 4/500 72 72 66 66 66 60 60 60 54 54 54 48 48 48 42
• Y ields great strength with minimal UP TO 60% RATED TENSION 12 16 18 20 24 5/625 84 78 78 72 72 66 66 60 60 54 54 54 48 48 48
stretch. Ideal when take-up is in MAXIMUM ELEVATOR BUCKET PROJECTION (in.) 6/750 96 90 84 84 78 78 72 72 66 66 60 60 54 54 54
LIGHT DUTY (GRAIN) 7 8 10 11 11
short supply 2/450 60 60 54 54 48 48 42 42 36 36 30 30 24 24 NR
HEAVY DUTY (INDUSTRIAL) 6 7 9 9 10 3/675 72 66 60 66 60 54 54 54 48 48 48 42 42 36 36
• Unique S&Z twist offers superior 4/900 84 72 72 72 66 66 72 60 60 54 54 48 48 42 42
5/1125 84 78 78 72 72 72 66 66 66 60 60 60 54 54 48
tracking
6/1350 90 84 84 78 78 78 72 72 72 66 66 66 60 60 60
64 7
5
LEGEND
Recommended Load Support
MATERIAL WEIGHT LB./FT.3 0-40 41-80 81-120 121-180 181-240
POLYESTER WARP • NYLON FILL • CRO WFOOT WEAVE DEGREE OF TROUGH 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
This tough belt handles heavy-duty jobs with ease 2/470 54 54 54 48 48 48 42 42 36 36 36 30 30 24 NR
The crowfoot carcass design in our Legend line-up is one heavy hitter … with peak strength, low stretch and 3/705 66 66 60 60 54 54 54 48 48 42 42 36 36 30 30
4/940 78 72 72 66 66 60 60 54 54 48 48 48 42 42 42
excellent tracking. This belt’s rugged polyester/nylon construction features a crowfoot weave which takes on
5/1175 84 78 72 72 72 66 66 66 60 60 60 60 54 48 48
heavy impact applications, like log handling, with ease and efficiency. It does the job usually reserved for an 90 84 84 78 78 72 72 66 66 60 60 60 54 54 48
6/1410
all-nylon carcass belt, with none of the usual challenges and answers the need where conditions are severe.
LEGEND — 235 PIW Polyester/Nylon Crowfoot Premium Carcass (EP 400 CF) Recommended Troughability
NUMBER OF PLIES 2 3 4 5 6 MINIMUM BELT WIDTH IN INCHES
BREAK TENSILE ( LB./PIW) 4700 7050 9400 11750 14100 BELT SPECIFICATION 2/470 3/705 4/940 5/1175 6/1410
OPERATING TENSILE ( LB./PIW)
• Crowfoot weave offers mechanical 20° Idler 20 24 36 42 48
HEAVY DUTY @ 10:1 SF 470 705 940 1175 1410 35° Idler 22 28 40 48 52
shock absorption and impact resis- ELEVATOR @ 10:1 SF 400 600 800 1000 1200 45° Idler 24 32 42 54 58
tance not found in plain weaves SKIM GAUGE (in.) 0.060 0.060 0.040 0.040 0.040
CARCASS GAUGE ( ± .010 in.) 0.155 0.265 0.320 0.405 0.495
• Increased puncture resistance due to MINIMUM PULLEY DIAMETER
increased fabric weight per square 81-100% RATED TENSION 20 24 30 34 38
foot 61-80% RATED TENSION 18 20 26 30 34
UP TO 60% RATED TENSION 14 16 20 24 28
• Nylon fill yarns in conjunction with MAXIMUM ELEVATOR BUCKET PROJECTION (in.)
LIGHT DUTY (GRAIN) 10 11 13 14 14
crowfoot weave offers superior
HEAVY DUTY (INDUSTRIAL) 9 10 12 12 13
resistance to ripping, tearing and
punctures
* Best suited for log decks but not for submerged water applications. Not warranted against wicking and water
• Available in 235 lb. rated fabric blistering.
6 7
LEGEND LEGEND-200 PIW Nylon/Nylon Premium Carcass (PP350)
NUMBER OF PLIES
BREAK TENSILE (LB/PIW)
2
5200
3
7800
4
10400
5
13000
6
15600
OPERATINGTENSILE(LB/PIW)
HEAVY DUTY @ 13:1 SF 400 600 800 1000 1200
NYLON WARP • NYLON FILL • PL AIN WEAVE SKIM GAUGE (in.) 0.06 0.06 0.04 0.04 0.04
CARCASS GAUGE (±0.010 in.) 0.2 0.33 0.44 0.51 0.62
MINIMUM PULLEY DIAMETER
Our legendary nylon/nylon design, with proven strength and elongation … where and
81-100% RATED TENSION 18 22 28 32 36
when you need it 61-80% RATED TENSION 16 18 24 28 32
This belt harkens back to a day when nylon was the carcass fabric of choice, due to its superior strength and UP TO 60% RATED TENSION 12 14 18 22 26
elongation. Under stress, the nylon yarns elongate to better absorb and resist force without breaking. Today,
this legendary belt remains one of the best all-nylon belts around, delivering a reliable performance under the
most challenging conditions.
Recommended Load Support
MATERIAL WEIGHT LB./FT.3 0-40 41-80 81-120 121-180 181-240
DEGREE OF TROUGH 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
LEGEND — 75 PIW Nylon/Nylon Premium Carcass (PP 100) 2/150 36 36 30 30 30 NR 24 24 NR 24 NR NR NR NR NR
NUMBER OF PLIES 2 3 4 5 6 3/225 42 42 42 36 36 30 36 30 30 30 24 NR 24 24 NR
BREAK TENSILE (LB/PIW) 1950 2925 3900 4875 5850 4/300 48 48 48 48 42 42 36 36 30 36 30 30 30 24 24
OPERATINGTENSILE(LB/PIW) 2/220 42 42 36 36 30 30 30 30 24 24 24 NR NR NR NR
HEAVY DUTY @ 13:1 SF 150 225 300 375 450 3/330 48 48 42 42 42 36 36 36 30 30 30 24 24 NR NR
SKIM GAUGE (in.) 0.050 0.050 0.030 0.030 0.030 4/440 60 54 54 48 48 48 42 42 42 36 36 36 36 30 30
CARCASS GAUGE (±0.010 in.) 0.130 0.205 0.230 0.305 0.380 5/550 66 66 66 60 60 60 54 54 54 54 48 48 48 48 42
• Nylon warp and nylon fill carcass MINIMUM PULLEY DIAMETER 6/660 72 72 72 66 66 66 60 60 60 60 54 54 54 48 48
81-100% RATED TENSION 8 12 17 22 28
construction 2/400 54 54 54 48 48 48 42 42 36 36 36 30 30 24 24
61-80% RATED TENSION 5 8 14 17 22
3/600 66 66 66 60 54 54 54 48 48 42 42 36 36 30 30
UP TO 60% RATED TENSION 3 6 10 12 18
• Offers superior strength and high 4/800 78 78 78 66 66 60 60 54 54 42 42 42 36 36 36
elongation 5/1000 84 84 84 72 72 66 66 66 60 60 60 60 54 48 48
6/1200 90 90 90 78 78 72 72 66 66 60 60 60 54 54 48
• Superior resistance against tears,
punctures and rips
• Excellent choice in conditions where LEGEND — 110 PIW Nylon/Nylon Premium Carcass (PP 200) Recommended Troughability
the possibility of punctures can’t be NUMBER OF PLIES 2 3 4 5 6 MINIMUM BELT WIDTH IN INCHES
minimized, such as concrete recycling, BREAK TENSILE (LB/PIW) 2860 4290 5720 7150 8580 BELT SPECIFICATION 2/150 3/225 4/300
OPERATINGTENSILE(LB/PIW) 20° Idler 14 20 30
or where elongation is critical to
HEAVY DUTY @ 13:1 SF 220 330 440 550 660 35° Idler 18 26 36
performance, like in High Angle or SKIM GAUGE (in.) 0.050 0.050 0.030 0.030 0.030 45° Idler 22 32 42
Sandwich conveyors CARCASS GAUGE (±0.010 in.) 0.145 0.245 0.288 0.330 0.425 BELT SPECIFICATION 2/220 3/330 4/440 5/550 6/660
MINIMUM PULLEY DIAMETER 20° Idler 16 18 24 30 36
• Dependable option for belt-over-chain 81-100% RATED TENSION 14 18 23 28 34 35° Idler 20 24 30 36 42
or applications where substantial 61-80% RATED TENSION 12 16 20 23 28 45° Idler 24 30 36 42 48
UP TO 60% RATED TENSION 10 12 16 16 22
bolt-holding abilities are needed BELT SPECIFICATION 2/400 3/600 4/800 5/1000 6/1200
20° Idler 20 24 36 42 48
35° Idler 22 28 40 48 52
45° Idler 24 32 42 54 58
8 9
VIPER
The Unique Weave is the Solution for Demanding Applications
The yarns in plain woven fabrics have a natural crimp. Once the belt is put under tension, this crimp is pulled
out; resulting in unwanted belt stretch. The straight warp yarns of our Viper and Viper II fabric range do not
straighten out like those of crimped yarns, thus eliminating much of the initial belt stretch. The belt design VIPER II — Polyester/Nylon/Nylon Straight Warp Premium Carcass
NUMBER OF PLIES 2 2 2 2
provides for maximum load support, yet remains quite flexible for high tension constructions. This makes our
BREAK TENSILE ( LB./PIW) 4000 6000 8000 10000
Viper line a great choice for wide conveyors, as well as, narrow, high tension conveyors of long distances.
OPERATING TENSILE ( LB./PIW)
Designed for Impact Resistance HEAVY DUTY @ 10:1 SF 400 600 800 1000
ELEVATOR @ 10:1 SF 340 510 680 850
By packing tremendous break strength into the one or two plies of the Viper and Viper II, Legg must use very
SKIM GAUGE (in.) 0.080 0.080 0.080 0.080
large yarns. These yarns, in addition to the unique fabric construction, are much more resistant to rip, tear, CARCASS GAUGE ( ± .010 in.) 0.231 0.254 0.304 0.321
and puncture than the lighter yarns found in plain woven belt fabrics which require three, four, or five plies for MINIMUM PULLEY DIAMETER
equal strength. Once the belt has been vulcanized with premium rubber covers, and a thick rubber skim for 81-100% RATED TENSION 24 24 30 36
two ply constructions, the belt is fully equipped to dampen impact forces and will absorb stresses put on the 61-80% RATED TENSION 20 20 24 30
UP TO 60% RATED TENSION 18 18 20 24
belt by large/heavy materials.
MAXIMUM ELEVATOR BUCKET PROJECTION (in.)
LIGHT DUTY (GRAIN) 13 15 16 18
• The high modulus straight warp HEAVY DUTY (INDUSTRIAL) 12 14 15 16
carcass, incorporating longitudinal
warp yarns with virtually no crimp,
was engineered for low stretch VIPER — Polyester/Nylon/Nylon Straight Warp Premium Carcass Recommended Load Support
NUMBER OF PLIES 1 1 1 1 MATERIAL WEIGHT LB./FT.3 0-40 41-80 81-120 121-180 181-240
• Unique Polyester/Nylon/Nylon BREAK TENSILE ( LB./PIW) 2200 3300 4400 5500 DEGREE OF TROUGH 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
OPERATING TENSILE ( LB./PIW) BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
carcass has unmatched impact
HEAVY DUTY @ 10:1 SF 220 330 440 550 I/220 48 42 36 42 36 36 36 30 NR 30 NR NR NR NR NR
resistance
ELEVATOR @ 10:1 SF 185 280 375 470 I/330 72 60 54 60 54 48 54 48 42 48 42 NR 42 NR NR
CARCASS GAUGE ( ± .010 in.) 0.095 0.120 0.125 0.130 I/440 84 72 60 72 60 54 60 54 48 54 48 36 48 42 NR
• Polyester warp + nylon weft +
MINIMUM PULLEY DIAMETER I/550 84 72 60 72 60 48 72 60 48 60 54 42 54 48 42
nylon binder = excellent rip & tear 81-100% RATED TENSION 14 18 20 24 II/400 84 72 66 72 66 60 72 60 54 60 54 48 54 48 42
resistance 61-80% RATED TENSION 12 16 18 20 II/600 84 84 72 84 72 72 84 72 60 72 60 54 60 54 48
UP TO 60% RATED TENSION 10 14 16 18 II/800 84 84 84 84 84 84 84 84 72 84 72 60 72 60 54
• The VIPER one and two ply car- MAXIMUM ELEVATOR BUCKET PROJECTION (in.) II/1000 84 84 84 84 84 84 84 84 84 84 78 72 72 66 60
cass designs provide excellent LIGHT DUTY (GRAIN) 8 10 10 12
troughability when compared to HEAVY DUTY (INDUSTRIAL) 7 9 10 10
multi-ply, high strength belt con- Recommended Troughability
structions MINIMUM BELT WIDTH IN INCHES
BELT SPECIFICATION I/220 I/330 I/440 I/550
• Superb load support allows for safe VIPER & VIPER II WEAVE 20° Idler 14 20 24 24
material transport at wide widths Fill Yarn 35° Idler 18 24 30 30
Warp Yarn
45° Idler 24 30 36 36
• The VIPER high tensile constructions BELT SPECIFICATION II/400 11/600 II/800 II/1000
remain flexible enough to bend 20° Idler 24 24 30 30
around small pulleys 35° Idler 30 30 36 36
45° Idler 36 36 42 42
Binder Yarns
10 11
CHAMPION Recommended Load Support
MATERIAL WEIGHT
(LB/FT3)
0-40 41-80 81-120 121-180 181-240
DEGREE OF 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
TROUGH
BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
Formulated to meet the needs of today’s world market
2/150 36 36 30 30 30 24 24 24 18 18 NR NR NR NR NR
Our Champion line truly lives up to its name; combining this carcass with one of Legg’s superior compounds 3/225 48 48 42 42 42 42 42 36 36 30 30 24 24 NR NR
ensures a belt that will meet worldwide demands at competitive prices. Compounded with high quality poly- 4/300 60 60 54 60 60 54 54 54 48 54 48 42 48 42 36
mers, additives, inhibitors and curing agents, the Champion is a true competitor, on par with top-line belting 5/375 72 60 54 60 60 54 54 54 48 54 48 42 48 42 36
shipped the world over. 2/180 36 36 30 30 30 24 24 24 18 18 NR NR NR NR NR
3/270 48 48 42 42 42 42 36 36 36 30 30 24 24 NR NR
4/360 60 60 54 54 54 48 48 48 42 42 42 36 36 36 30
5/450 72 66 66 66 60 60 60 54 54 54 48 48 48 42 42
6/540 84 78 72 72 72 66 66 66 60 60 60 54 54 54 48
retention
12 13
CHAMPION
CHAMPION — 110 PIW Polyester/Nylon Carcass (EP 200)
NUMBER OF PLIES 2 3 4 5 6
BREAK TENSILE (LB/PIW) 2200 3300 4400 5500 6600
OPERATINGTENSILE(LB/PIW)
HEAVY DUTY @ 10:1 SF 220 330 440 550 660
ELEVATOR @ 10:1 SF 190 290 380 480 575
SKIM GAUGE (in.) 0.050 0.050 0.030 0.030 0.030
CARCASS GAUGE (±0.010 in.) 0.130 0.220 0.245 0.315 0.380
MINIMUM PULLEY DIAMETER
81-100% RATED TENSION 16 20 25 30 36 Recommended Load Support
61-80% RATED TENSION 14 18 22 25 30 MATERIAL WEIGHT
(LB/FT3)
0-40 41-80 81-120 121-180 181-240
UP TO 60% RATED TENSION 10 14 16 18 24
MAXIMUM ELEVATOR BUCKET PROJECTION (in.) DEGREE OF 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45° 20° 35° 45°
LIGHT DUTY (GRAIN) 6 8 9 10 11 TROUGH
HEAVY DUTY (INDUSTRIAL) 5 7 8 9 10 BELT SPECIFICATION MAXIMUM BELT WIDTH IN INCHES
2/220 42 42 36 36 36 30 30 30 24 24 24 18 NR NR NR
3/330 54 54 54 48 48 48 42 42 42 36 36 36 30 30 30
4/440 66 66 60 60 60 54 54 54 48 48 48 42 42 42 36
CHAMPION — 200 PIW Polyester/Nylon Carcass (EP 350) 5/550 78 72 72 72 66 66 66 60 60 54 54 48 48 48 42
NUMBER OF PLIES 2 3 4 5 6
6/660 90 84 78 72 72 72 66 66 66 60 60 60 54 54 48
BREAK TENSILE (LB/PIW) 4000 6000 8000 10000 12000
OPERATINGTENSILE(LB/PIW) 2/400 54 54 54 48 48 48 42 42 36 36 36 30 30 24 24
HEAVY DUTY @ 10:1 SF 400 600 800 1000 1200 3/600 66 66 60 60 54 54 54 48 48 42 42 36 36 30 30
ELEVATOR @ 10:1 SF 350 500 680 850 1000 4/800 78 72 72 66 66 60 60 54 54 48 48 48 42 42 42
SKIM GAUGE (in.) 0.060 0.060 0.040 0.040 0.040
5/1000 84 78 72 72 72 66 66 66 60 60 60 60 54 48 48
CARCASS GAUGE (±0.010 in.) 0.170 0.290 0.350 0.445 0.537
6/1200 90 84 84 78 78 72 72 66 66 60 60 60 54 54 48
MINIMUM PULLEY DIAMETER
81-100% RATED TENSION 20 24 30 34 38 2/500 60 60 54 54 54 48 48 42 42 36 36 30 30 24 24
61-80% RATED TENSION 18 20 26 30 34 3/750 72 66 66 54 54 54 48 48 48 42 42 36 36 30 30
UP TO 60% RATED TENSION 14 16 20 24 28
4/1000 84 78 72 66 66 60 60 54 54 48 48 48 42 42 36
MAXIMUM ELEVATOR BUCKET PROJECTION
LIGHT DUTY (GRAIN) 10 11 12 13 14 5/1250 90 84 72 72 72 66 66 60 60 54 54 54 48 48 42
HEAVY DUTY (INDUSTRIAL) 9 10 11 12 13 6/1500 96 90 84 78 78 72 72 66 66 60 60 60 54 54 54
Recommended Troughability
MINIMUM BELT WIDTH IN INCHES
CHAMPION — 250 PIW Polyester/Nylon Carcass (EP 500) BELT SPECIFICATION 2/220 3/330 4/440 5/550 6/660
NUMBER OF PLIES 2 3 4 5 6
20° Idler 14 18 24 30 36
BREAK TENSILE (LB/PIW) 5000 7500 10000 12500 15000
35° Idler 18 22 28 33 42
OPERATINGTENSILE(LB/PIW)
HEAVY DUTY @ 10:1 SF 500 750 1000 1250 1500 45° Idler 22 24 32 36 48
ELEVATOR @ 10:1 SF 425 640 850 1060 1275
BELT SPECIFICATION 2/400 3/600 4/800 5/1000 6/1200
SKIM GAUGE (in.) 0.060 0.060 0.040 0.040 0.040
20° Idler 20 24 36 42 48
CARCASS GAUGE (±0.010 in.) 0.227 0.372 0.452 0.582 0.702
MINIMUM PULLEY DIAMETER 35° Idler 22 28 40 48 52
81-100% RATED TENSION 22 24 32 36 40 45° Idler 24 32 42 54 58
61-80% RATED TENSION 20 22 28 32 36
BELT SPECIFICATION 2/500 3/750 4/1000 5/1250 6/1500
UP TO 60% RATED TENSION 16 18 24 28 30
20° Idler 24 28 40 46 52
MAXIMUM ELEVATOR BUCKET PROJECTION (in.)
LIGHT DUTY (GRAIN) 11 12 13 14 15 35° Idler 26 32 44 52 56
HEAVY DUTY (INDUSTRIAL) 10 11 12 13 14 45° Idler 28 36 46 58 62
14 15
COVER
COMPOUNDS
GENERAL PURPOSE/ABRASION RESISTANT
COMPOUND (INTERNATIONAL DESIGNATION)
TEST STANDARD UNIT GII XT-GII (Z,L) GI (N-17) XT-GI FF (K,W) GI-P (M,H,X,Y)
GII—General duty compound. Good abrasion, cut and gouge resistance make this a good economical good
PSI (min.) 2000 2200 2500 2700 2610 3626
choice. TENSILE ISO 37
MPa (min.) 13.8 15.2 17.2 18.6 18.0 25.0
ELONGATION ISO 37 % (min.) 400 450 450 500 400 450
XT-GII—Premium compound; exceeds ARPM Grade 2 specs. Yields superior abrasion, great tensile, great
HARDNESS ISO 48 Shore A 60 ± 5 60 ± 5 60 ± 5 60 ± 5 70 ± 5 70 ± 5
tear and elongation values. Combine with a Legend carcass for a superior belt.
ISO 4649-2002
ABRASION INDEX (DIN 53516) mm3 (max.) 250 175 150 120 90 120
GI—General purpose compound. Offers good abrasion, cut and gouge resistance; excellent choice for OZONE ASTM D1171 Pass / Fail Pass Pass Pass Pass Pass Pass
handling larger rock, or sharp, heavy material. Fahrenheit (ºF) -40 to 225* -50 to 225* -40 to 225* -50 to 225* -40 to 225* -40 to 225*
TEMPERATURE RANGE
Celsius (ºC) -40 to 107* -46 to 107* -40 to 107* -46 to 107* -40 to 107* -40 to 107*
XT-GI—Exceeds ARPM’s Grade 1 specs; an excellent choice when better abrasion, cut and gouge resis- OIL SWELL ASTM D-471 % (max.) N/A N/A N/A N/A N/A N/A
tance is required. (100°C - 72 HRS. IN IRM 903 OIL)
STATIC CONDUCTIVE (≤ 300 MΩ) ISO 284 YES / NO NO NO NO NO NO NO
FF (Force Field)—Specially formulated for high abrasion applications, Force Field is the semi-truck tire * Maximum conveyed material temperature. Cycle times, belt cooling and other conditions may affect belt performance & life cycle.
GI-P (Grade I Premium)—Premium compound for heavy rock or high-impact applications, with high
elongation and tensile to prevent tearing. Couple with a Legend Polyester/Nylon carcass for an exceptional
primary belt or under crusher belt.
GHS (Grain Handler Supreme)—The Grain Handler Supreme features a pure Nitrile composition, mak- OZONE ASTM D1171 Pass / Fail Pass Pass Pass Pass Pass
ing it ideal to handle grains without worry. GHS is ideal for more oily applications, like conveying crushed Fahrenheit (ºF) -40 to 180* -40 to 225* -30 to 400* -40 to 225* -20 to 225*
TEMPERATURE RANGE
canola, but is also well suited for use with mineral oil dust suppression systems. Celsius (ºC) -40 to 82* -40 to 107* -34 to 204* -40 to 107* -29 to 107*
OIL SWELL
(100°C - 72 HRS. IN IRM 903 OIL) ASTM D-471 % (max.) 100 90 N/A 10 N/A
HH (High Heat)—An EPDM with good-to-excellent heat resistance at temperatures ranging to 400°F;
STATIC CONDUCTIVE (≤ 300 MΩ) ISO 284 YES / NO NO NO NO NO NO
offers outstanding ozone and oxidation resistance, as well as very good abrasion resistance. Ideal for * Maximum conveyed material temperature. Cycle times, belt cooling and other conditions may affect belt performance & life cycle.
handling high temperature and very abrasive products – like clinker.
HAHOR (Hot Asphalt/Heat and Oil Resistant)/VOR (Very Oil Resistant)—A high-heat NBR
formulated to withstand the high temperatures and heavy oils of the asphalting industry; offers excellent
abrasion, while maintaining required oil resistance. Heat resistant up to 350°F, but only achievable when
heavy oil is present; not rated above 225°F otherwise.
16 17
COVER
COMPOUNDS
FLAME-RESISTANT SERVICE COMPOUND (INTERNATIONAL DESIGNATION)
FR—A compound that meets requirements of the ASTM D-378 Part 13.2 flame retardant test. Suited for below TEST STANDARD UNIT FR FR-MOR GHS WFG-SBR WFG-NBR
PSI (min.) 2000 2000 1800 2000 1700
ground applications where fire retardant belt is required; allowed by USBM and MSHA to be used under- TENSILE ISO 37
MPa (min.) 13.8 13.8 12.4 13.8 11.7
ground, as long as it is not a coal mining operation.
ELONGATION ISO 37 % (min.) 450 450 450 450 450
FR-MOR (Moderately Oil Resistant)—A compound that meets requirements of the ASTM D-378 Part HARDNESS ISO 48 Shore A 60 ± 5 65 ± 5 63 ± 5 60 ± 5 67 ± 5
ABRASION INDEX ISO 4649-2002 (DIN 53516) mm3 (max.) 200 200 250 250 250
13.2 flame retardant test and delivers a degree of oil resistance for product treated with oily additives for
OZONE ASTMD1171 Pass / Fail Pass Pass Pass Pass Pass
dust suppression.
Fahrenheit (ºF) -40 to 225* -40 to 225* -50 to 225* -40 to 225* -30 to 225*
TEMPERATURE RANGE
Celsius (ºC) -40 to 107* -40 to 107* -45 to 107* -40 to 107* -34 to 107*
MSHA CFR Title 30,
FOOD GRADE SERVICE FIRE RETARDANT Part 14 NO NO NO N/A N/A
ASTM D-378 Part 13.2 YES YES YES N/A N/A
WFG-SBR (White Food Grade SBR)—A compound designed for handling consumable food products, OIL SWELL ASTM D-471 % (max.) N/A 90 10 N/A 10
(100°C - 72 HRS. IN IRM 903 OIL)
or for products that will be consumed by consumable livestock. SBR offers good abrasion resistance in
STATIC CONDUCTIVE (≤ 300 MΩ) ISO 284 YES / NO YES YES YES NO NO
the absence of carbon black. Meets FDA requirements and is viable for use with non-oily products such as * Maximum conveyed material temperature. Cycle times, belt cooling and other conditions may affect belt performance & life cycle.
sugar, dehydrated potatoes, flour.
WFG-NGR (White Food Grade Nitrile)—A compound for use in handling consumable food products,
or for products that will be consumed by consumable livestock, both having high oil content. A pure Nitrile
compound, it offers the highest level of oil resistance to handle meat, soybean meal and precooked potato
products. Good abrasion, cut and gouge resistance, and meets FDA requirements.
excellent cut and gouge resistance and excellent abrasion resistance. For use with a variety of products,
from corrugated boxes to scrap iron. Also offers excellent oil resistance to most oils. Available in Rust or
Blue.
18 19
typ.
Section A-A .50"
typ.
135° typ.
.50"
.50" typ.
3" typ.
R 2.50"
typ.
1"
6" 6"
1/4" Tall
BELT PROFILES
Available up to 72" wide.
Cleat height = 1/4" 5 1/2"
5/16"
1 3/4"
HERCULES
90°
12"
30° • Sturdy option offers hours of dependable service
1-1/2"
• ¾˝ x ¾˝ Chevron style cleat moves bulk material efficiently
We have a profile to meet every need … and a design that keeps
1/2" product 1/2"
moving .75" up inclines
along efficiently 1/2"
.75" typ.
• Overlapping pattern and 60º bevel provides quiet and smooth
.75"
When conveying product up an incline is critical, you need an integrally-molded
A
A
profile solution,
Section A-A
where 9.0" return; while 9˝ spacing gives maximum material traction
cleat and belt work as one homogenous unit. With Legg profiles, you’ll find78°high-performance profile 6"
R .375 typ. • Available in Legend and Champion carcasses to carry wood chips,
continuous
designs that cater to a varietymega-bite
135°
of product needs and conditions, from wood chips and sawdust, toatlasriver 48 A
1/2"
split hercules
6"
.75"
continuous 6.00" typ.
rocks or30°high animal fat cattle feed mega-bite atlas 48
1/2" 30°
1/2" 1/2"
A
1" 1/2"
MEGA-BITE
.708" 10"
6"
MINI-BITE 1"
36"
135° 6.00" typ.Section B-B 9"
1"
36" 22.5"
A
1/2" FRAC BELT 3/4"
1/2" 6" 30° 3/8"
• ½˝ x ½˝ bucket pattern offers exceptional material bite
A
22.5"
45° 135° 3/4"
• Excellent for bulk material, such as grain, nut hulls1/2" Section A-A
FRAC BELT A typ.
A 7/8" 3/8"
2" 2" 1.062" 5/16" 3/4"
• Integrally-molded design ensures cleats won’t come loose
.039" B 90° A 1/2"
3/16" Tall 3-13/16" 1"
36"
1-1/2" .173" or sawdust
2" 2"
3/16" Tall
5/16"
13"
B 23°
B 90°
B 0.50"
B
typ. B B
.50"
1-1/2"
R 1.5" 3" Section A-A
• Angled cleat ends with overlapping pattern enhance quiet vibration
B B 2" 2" 5/16" Section A-A B Section A-A
90° 90°
• Full width slit-able construction
B 23° typ. 40º R .375"
3/16" Tall
22.5"
R 1.5" Available up to 72" wide 85°
FRAC BELT 40º R .375" .157" BA 23° 135° typ.
Cleat height = 3/16" 2" Section A-A A A .50"
free return
5/32" Available up to 72" wide Section B-B .50" 13" Section AA (not to scale)
typ. 85°
• Available
Cleat height = in all Legg carcass options and most covers
A A A Cleat end same for all cleats
13" Section AA (not to scale)
3"
Available up to 72" wide
7/16" 3/16" 2" typ. 85°
A Cleat end same for all cleats 45° 5/32" A A
• Available in 24˝, 30˝ and 36˝ patterns on up to a 48˝ belt
1-1/2" Cleat height = 3/16" 2" A 3/4" 3/8" Section B-B
• 22” min. width7/16"
B B 5/32" Section B-B 3/8" 6.1" Angled cleat end
45° 1.250" 7/8" 27"AA
6.1" Angled cleat end
R 1.5"
40º R .375" 7/16" 45° 10" 1/2"
R 2.50" 27" same as section
3/4" 3/8"
same as section AA 1"3/4" 3/8" typ. 8.5" 4º 1.0" typ.
1.250" 2" 7/8" 3/8" 27"
A 8.5" 3/8" 1.0" typ.
R .375" 27"
2" 13"
4º
Section AA (not to scale) 1.250" 7/8" 10" 1"27" 1/2" 1-1/4" 27" 5/8" 1.0" typ.
all cleats 6"
Cleat end same for 6"
1" Section A-A
A R .375" 10" 1" 1/2" 8.5" 8.3" 1.00" 1.0"
Stone typ.
slinger 1.0" typ.
1-1/4" 5/8" 1/4" Tall Section BB (not to scale)
typ. typ.
8.5" 8.3" Section A-A Cleat profile same for1.0" all cleats
Section BB (not to scale) 12.00"typ.
MEGA-BITE II
6.1" Angled cleat end Section A-A 1.00"
same as section AA
Cleat profile same for all cleats maxi-bite super V Titan 42 1.00" typ.
Available up to 72" wide. 14"
typ.
8.5" 4º 5 1/2" 12.00"typ.
2"
1-1/4" 5/8"
Cleat height = 1/4"
R .375" 5/16"
1 7/8" MAXI-BITE 12 1/2"
1/2" 1/2" 12" 6.00"12.00"
typ.
typ.
8" • Offers extreme bite to move product up steep inclines
8.5" 1 3/4" 90°
• ½˝ x ½˝ cleats molded6.00"from top cover; won’t come loose
8.3" Section BB (not to scale) typ.
Cleat profile same for all cleats
• Takes more than a Mini Bite – Maxi Bite takes 6 1/4" it up a notch 1/2"
135°
6"6.00" typ.
6.00" typ.
3 3/4"
• Aggressive 1/4” tall cleat profile 3"
A
• Slit-able construction is available up • Cleat pattern keeps product in belt center 0.50"
12" to 60” wide
90° 3-13/16" 1/2"
4 3/8" 90° 1/2"
• 18˝, 24˝, 30˝, 36˝ and 42˝ patterns on up to atyp.48˝ belt.50"
12" 12" A
1/2" 30°
• Available in all Legg carcass
1-1/2"
options and most covers
6" 6" A Section A-A
1 3/8" typ.
• 42˝, 48˝, 54˝, 60˝ and 66˝ patternstyp.on up to a 72˝ .50" belt
5 1/2" 1/4" 135°
1/2" .50"
5/16" • 42” min. width 1/2"
3 11/16" 14° 1/2"
typ.
typ.
3" 3/8"
• Available in all Legg carcass options and most covers
1 3/4" 70° .75"
Section A-A
.75" typ.
1/2"
.75" R 2.50"
typ.
A
Section A-A 9.0"
A 1"
6" 6"
78° 1/4" Tall R .375 typ.
.75"
20 21
Available up to 72" wide.
36"
22.5"
Cleat height = 1/4" 5 1/2"
FRAC BELT 5/16"
1 3/4"
R 2.50" 8"
typ. 1/2" 1/2" 12"
1 7/8" 12 1/2"
90°
6 1/4" 1/2"
3 3/4" 9 1/2"
3"
90°
12"
30°
1-1/2"
1/2" 1/2"
36" .75"
.75" typ.
22.5"
1/2" FRAC BELT
.75"
Titan 42
STONE SLINGER
14"
1/4" 1/2"
• Aggressive 3/8” tall cleat moves bulk material at high speeds
9 1/2"
• Cover compounds are available for various bulk materials
3"
A
1/2"
4 3/8" 90° 1/2"
such as aggregate or wood chips
A
A
3/4"
3/8"
3/8"
7/8"
1.062" .039"
• Available in widths up to 60” Section A-A A
B
1" 1/2"
3/4"
.173"
• 24” min. width 13"
90°
B Section A-A 3" Section A-A
.157"
Section A-A
T-CLEATS
0.25" 0.500"
R 0.625"
1.500"
2.00"
Stone slinger
1.58"
0.72"
maxi-bite
R 0.50"
• Choose from a wide variety of cleat heights on any carcass
super V Titan 42
14"
• Integrally-molded during initial curing for 100% homogenous
0.32"
0.30"
• Center to center dimensions available 6on 6˝, 12˝, 18˝ and 24˝,
0.70"
1.47"
1.43"
1/4" 1/2"
12"
3 3/4"
with other centers available 3" 9 1/2"
22 23
C TC/TCW T/TW
LEGG-WALL
Reliable conveying at Product Range
inclines of up to 90º
LEGG-WALL belts can be supplied in either M (light), MW (medium) or MWS (heavy) corrugated
The LEGG-WALL portfolio of corrugated sidewalls. All products with “W” included in its description / nomenclature are fabric reinforced which
sidewall belts for transport of bulk provides for greater stability.
goods offer high-quality, long term,
LEGG-WALL corrugated sidewalls and cleats are produced in standard, oil-resistant or heat-resistant
high-incline conveying solutions.
qualities. Other types are available by request.Type C, TC, TCW, T and TW cleats can be combined
Depending on the application, there are
individually with their respective sidewalls. The LEGG-WALL belt range offers
three corrugated sidewall types and
three cleat types to choose from. Each Note: Minimum pulley diameter is dependent on sidewall, cleat and base belting. a comprehensive selection of
cleat and sidewall type is engineered
to meet the customer’s specific re- Corrugated Sidewall Range Cleat Range engineered components. This
quirements. Different cleat geometries
B C TC/TCW TC/TCW
enable us to achieve variable incline P
B C
T T T ensures
T the correct LEGG-WALL
P
angles from 0 to 90 degrees. H H
configuration for each custom
H H
W TW W T W
H H
H H designed application.
W T/TW T/TW
W W W
• Small footprint - Saves space by NOMINAL DIMENSIONS - CLEATS NOMINAL DIMENSIONS - SIDEWALL
H W P H W P
conveying at inclines up to 90º TYPE
in mm in mm in mm
TYPE
in mm in mm in mm
T 35 1.38 35 2.17 55 0.24 6 M 60 S 2.36 60 1.97 50 1.57 40
• Extremely high stability is provided T55 2.17 55 3.15 80 0.28 7 M60S 2.36 60 1.97 50 1.97 50
in the transverse direction while T 75 2.95 75 3.15 80 0.24 6 M 80 S 3.15 80 1.97 50 1.57 40
allowing good longitudinal flexibility T 90 3.54 90 4.13 105 0.43 11 M 80 S 3.15 80 1.97 50 1.97 50
T/TW 110 4.33 110 4.13 105 0.31 8 M 100 S 3.94 100 1.97 50 1.57 40
T/TW 140 5.51 140 6.30 160 0.71 18 M 100 3.94 100 1.97 50 1.97 50
• Standard belts include two special, T/TW 160 6.30 160 6.30 160 0.63 16 M 120 4.72 120 1.97 50 1.97 50
cross rigid fabrics T/TW 180 7.09 180 6.30 160 0.55 14 M 140 5.51 140 1.97 50 1.97 50
tions with steel C 90 3.54 90 4.33 110 0.31 8 MWS 120 4.72 120 2.95 75 2.36 60
C 110 4.33 110 4.33 110 0.28 7
TYPES OF BASE BELTS MWS 140 5.51 140 2.95 75 2.36 60
TC 75 2.95 75 3.23 82 0.28 7 MWS 160 6.30 160 2.95 75 2.36 60
TOP COVER BOTTOM COVER OVERALL BELT
TENSILE THICKNESS THICKNESS WEIGHT TC 90 3.54 90 4.13 105 0.47 12 MWS 180 7.09 180 2.95 75 2.36 60
BELT TYPE THICKNESS
STRENGTH TC/TCW 110 4.33 110 4.13 105 0.79 20 MWS 200 7.87 200 2.95 75 2.36 60
in mm in mm in mm lb./sq.ft.
TC/TCW 130 5.12 130 6.30 160 0.79 20 MWS 240 9.45 240 2.95 75 2.36 60
CROSS RIGID 2-150 + 2 3/16 4.8 3/32 2.4 0.509 12.9 3.57
TC/TCW 140 5.51 140 6.30 160 0.79 20 MWS 250 9.84 250 2.95 75 2.36 60
CROSS RIGID 2-250 + 2 3/16 4.8 3/32 2.4 0.557 14.1 4.41
TC/TCW 160 6.30 160 6.30 160 0.79 20
CROSS RIGID 3-375 + 2 3/16 4.8 3/32 2.4 0.637 16.2 5.51 TC/TCW 180 7.09 180 6.30 160 0.75 19
CROSS RIGID 4-500 + 2 3/16 4.8 3/32 2.4 0.717 18.2 6.61 TC/TCW 220 8.66 220 6.69 170 1.18 30
CROSS RIGID 5-625 + 2 3/16 4.8 3/32 2.4 0.797 20.2 7.72 TC/TCW 230 9.06 230 6.69 170 1.18 30
24 25
VACUUM
FILTER BELTS
Proven Performance in Any Dewatering Processes Belt Constructions
Vacuum filter belts from Legg are specifically designed to separate liquids and solids on horizontal belt Legg offers a variety of filter belt widths and constructions. Starting with a construction 24 inches wide with a single bottom guide, to a construction 60 inches wide
filter systems. These belts support the filter cloth, the filter cake and the filtrate within integrated skirts with five bottom guides, Legg offers a wide range of filter belt designs. Each Legg filter belt is tailor made for your specific model of horizontal vacuum filter.
or with additional curbing. The filtrate is removed by vacuum through the molded grooves in the top cover
and the drainage holes in the center of the belt.
In most cases the textile carcass of the belt must be protected from the filtered media. Legg offers filter
7
belts with a textile free drainage zone. The textile carcass is completely embedded in rubber and separat-
9
ed from both the drainage holes and the belt edges, thus protecting the carcass from both chemical and 2
thermal degradation. 1 6
5 4
3
• Bottom Guide 9
FILTER BELTS Depending on the filter design, the transport belt often requires either a single guide or multiple guides
Properties
on the bottom of the belt to assist in tracking and to keep the drainage holes centered over the vacuum
Legg manufactures the perfect solution box. Drainage holes run through the transport belt and bottom guide allowing access to the collection 1. Cover Compound 6. Full rubber edge 10
for traditional horizontal
9
belt filters duct. 3 • Good chemical resistance • Good lateral stability when guide pulleys are used
in widths up to 60 inches (1.5m). Our 8 • High temperature resistance
filter belts are engineered
10
with molded • Skirts/Curbing 7. Un-grooved edge zone 1
2. Molded transverse groove surface
2
drainage grooves, a fabric 1 free drainage
Integrated skirts hold the filter cake on top of the filter blanket and4 transport
7 belt. The addition of curbing
0.125" 0.50"
• Suitable for cold bonding or vulcanizing rubber curbing
6
0.250"
onto the belt
0.1 ad.
• Smooth surface
"
zone, an optional bottom guide and
25
R
3
can increase capacity and eliminate spillage. Curbing type and height 5 is determined for each specific
is available in a variety of premium application. 8 • Perfect pitch and dimensions of grooves and lands
8. Upward folding skirting
rubber compounds suitable for any HBF
2 3. Bottom guide • Edge zone can be folded up to desired containment height
application. 4 7 • No need to attach additional profiles
6 STANDARD CURBING • Single and multiple guide strip locations available
5 BASE WIDTH HEIGHT • Without curbing, required drive and tail pulley diameters
are reduced
A 2.5” 5” 4. 100% polyester carcass
Applications 0.125" 0.50" B 2” 3.5”
• High-strength
C 2” 3” 9. Smooth and seamless transition between base belt
• Low-elongation
0.250"
0.1 ad.
"
25
R
0.1 ad.
"
25
R
A 3.4” 4”
• Pharmaceuticals B 3.4” 5”
26 27
NOTES NOTES
325 East 10th Street
Halstead, KS 67056
USA
1-800-835-1003
leggbelting.com