Академический Документы
Профессиональный Документы
Культура Документы
1OUT
4OUT
1IN –
4IN –
A Versions . . . 15 nA Typ
NC
D Differential Input Voltage Range Equal to
Maximum-Rated Supply Voltage . . . 32 V
3 2 1 20 19
(26 V for LM2902 and LM2902Q) 1IN+ 4 18 4IN+
D Open-Loop Differential Voltage NC 5 17 NC
Amplification . . . 100 V/mV Typ VCC 6 16 GND
D Internal Frequency Compensation
NC 7 15 NC
3IN+
2IN+ 8 14
9 10 11 12 13
description
2IN –
3IN –
2OUT
NC
3OUT
These devices consist of four independent
high-gain frequency-compensated operational
amplifiers that are designed specifically to operate NC – No internal connection
from a single supply over a wide range of voltages.
Operation from split supplies is also possible symbol (each amplifier)
when the difference between the two supplies is
3 V to 30 V (for the LM2902 and LM2902Q, 3 V to
26 V) and VCC is at least 1.5 V more positive than IN –
–
PRODUCTION DATA information is current as of publication date. Copyright 1997, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
AVAILABLE OPTIONS
PACKAGED DEVICES
VERY CHIP
VIOmax SMALL CHIP CERAMIC PLASTIC FLAT
TA SMALL TSSOP FORM
AT 25°C OUTLINE CARRIER DIP DIP PACK
OUTLINE (PW)‡ (Y)
(D)† (FK) (J) (N) (W)
(DB)‡
0°C to 7 mV LM324D LM324DBLE — — LM324N LM324PWLE —
LM324Y
70°C 3 mV LM324AD — — — LM324AN LM324APWLE —
–25°C to 5 mV LM224D — — — LM224N — —
—
85°C 3 mV LM224AD — — — LM224AN — —
– 40°C to LM2902D — — LM2902N —
7 mV LM2902DBLE LM2902PWLE —
125°C LM2902QD — — LM2902QN —
– 55°C to 5 mV — — LM124FK LM124J — — LM124W
—
125°C 2 mV — — LM124AFK LM124AJ — —
† The D package is available taped and reeled. Add the suffix R to the device type (e.g., LM324DR).
‡ The DB and PW packages are only available left-end taped and reeled.
OUT
IN –
IN + ≈ 50-µA
Current
Regulator
GND
To Other
Amplifiers
COMPONENT COUNT
(total device)
Epi-FET 1
Transistors 95
Diodes 4
Resistors 11
Capacitors 4
VCC+
(1) (14)
(3) (4)
(2) (13) 1IN+ (1)
(2) 1OUT
1IN– (5)
(7) 2IN+
2OUT (6)
(10) 2IN–
3IN+ (8)
(3) (12) (9) 3OUT
3IN– (12)
(14) 4IN+
4OUT (13)
4IN–
62 (4) (11) (11)
GND
(5) (10)
CHIP THICKNESS: 15 TYPICAL
TJmax = 150°C
(6) (9)
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
LM124, LM124A
LM2902,
LM224, LM224A UNIT
LM2902Q
LM324, LM324A
Supply voltage, VCC (see Note 1) 32 26 V
Differential input voltage, VID (see Note 2) ± 32 ± 26 V
Input voltage, VI (either input) – 0.3 to 32 – 0.3 to 26 V
Duration of output short circuit (one amplifier) to ground at (or below) TA = 25°C,
unlimited unlimited
VCC ≤ 15 V (see Note 3)
Continuous total dissipation See Dissipation Rating Table
LM124, LM124A – 55 to 125
LM224, LM224A – 25 to 85
free air temperature range,
Operating free-air range TA °C
LM324, LM324A 0 to 70
LM2902, LM2902Q – 40 to 125
Storage temperature range – 65 to 150 – 65 to 150 °C
Case temperature for 60 seconds FK package 260 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds J or W package 300 300 °C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds D, DB, N, or PW package 260 260 °C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values (except differential voltages and VCC specified for the measurement of IOS) are with respect to the network GND.
2. Differential voltages are at IN + with respect to IN –.
3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
VCC – VCC –
RL = 2 kΩ 25°C
1.5 1.5
VCC – 1
VOH High-level output voltage RL = 10 kΩ 25°C V
.5
VCC = MAX, RL = 2 kΩ Full range 26 26 22
VCC = MAX, RL ≥ 10 kΩ Full range 27 28 27 28 23 24
VOL Low-level output voltage RL ≤ 10 kΩ Full range 5 20 5 20 5 20 mV
Large-signal
g g differential VCC = 15 V,, VO = 1 V to 11 V,, 25°C 50 100 25 100 100
† All characteristics are measured under open-loop conditions with zero common-mode input voltage unless otherwise specified. MAX VCC for testing purposes is 26 V for LM2902
and LM2902Q, 30 V for the others.
‡ Full range is –55°C to 125°C for LM124, – 25°C to 85°C for LM224, 0°C to 70°C for LM324, and – 40°C to 125°C for LM2902 and LM2902Q.
§ All typical values are at TA = 25°C.
3–5
SLOS066E – SEPTEMBER 1975 – REVISED FEBRUARY 1997
QUADRUPLE OPERATIONAL AMPLIFIERS
LM324, LM324A, LM324Y, LM2902, LM2902Q
LM124, LM124A, LM224, LM224A
electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise noted)
3–6
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
description
The TL08x JFET-input operational amplifier family is designed to offer a wider selection than any previously
developed operational amplifier family. Each of these JFET-input operational amplifiers incorporates
well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature
high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. Offset
adjustment and external compensation options are available within the TL08x family.
The C-suffix devices are characterized for operation from 0°C to 70°C. The I-suffix devices are characterized
for operation from – 40°C to 85°C. The Q-suffix devices are characterized for operation from – 40°C to 125°C.
The M-suffix devices are characterized for operation over the full military temperature range of – 55°C to 125°C.
symbols
TL081 TL082 (EACH AMPLIFIER)
TL084 (EACH AMPLIFIER)
OFFSET N1
IN + + IN + +
OUT OUT
IN – – IN – –
OFFSET N2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright 1999, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments On products compliant to MIL-PRF-38535, all parameters are tested
standard warranty. Production processing does not necessarily include unless otherwise noted. On all other products, production
testing of all parameters. processing does not necessarily include testing of all parameters.
TL081M TL082M
U PACKAGE U PACKAGE
(TOP VIEW) (TOP VIEW)
NC 1 10 NC NC 1 10 NC
OFFSET N1 2 9 NC 1OUT 2 9 VCC+
IN– 3 8 VCC+ 1IN– 3 8 2OUT
IN+ 4 7 OUT 1IN+ 4 7 2IN–
VCC– 5 6 OFFSET N2 VCC– 5 6 2IN+
VCC+
1OUT
NC
NC
NC
NC
NC
NC
NC
3 2 1 20 19
NC 4 18 NC
3 2 1 20 19 1IN – 5 17 2OUT
NC 4 18 NC
NC 6 16 NC
IN – 5 17 VCC +
1IN + 7 15 2IN –
NC 6 16 NC
NC 8 14 NC
IN + 7 15 OUT 9 10 11 12 13
NC 8 14 NC
9 10 11 12 13
2IN +
NC
NC
NC
VCC –
OFFSET N2
NC
NC
NC
VCC –
TL084M . . . FK PACKAGE
(TOP VIEW)
4OUT
1IN –
4IN –
D, J, N, PW, OR W PACKAGE
NC
(TOP VIEW)
3 2 1 20 19
1OUT 4OUT 1IN + 4 18 4IN +
1 14
1IN – 4IN – NC 5 17 NC
2 13
1IN + 4IN + VCC + 6 16 VCC –
3 12
VCC + VCC – NC 7 15 NC
4 11
2IN + 5 10 3IN + 2IN + 8 14 3IN +
9 10 11 12 13
2IN – 6 9 3IN –
2IN –
3IN –
2OUT
NC
3OUT
2OUT 7 8 3OUT
NC – No internal connection
IN +
64 Ω
IN –
OUT
128 Ω
64 Ω
C1
1080 Ω 1080 Ω
VCC –
OFFSET N1 OFFSET N2
TL081 Only
61 (4)
(8) (4)
VCC –
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
TL08_C
TL08_AC TL08_I TL084Q TL08_M UNIT
TL08_BC
Supply voltage, VCC + (see Note 1) 18 18 18 18 V
Supply voltage VCC – (see Note 1) – 18 – 18 – 18 – 18 V
Differential input voltage, VID (see Note 2) ± 30 ± 30 ± 30 ± 30 V
Input voltage, VI (see Notes 1 and 3) ± 15 ± 15 ± 15 ± 15 V
Duration of output short circuit (see Note 4) unlimited unlimited unlimited unlimited
Continuous total power dissipation See Dissipation Rating Table
Operating free-air temperature range, TA 0 to 70 – 40 to 85 – 40 to 125 – 55 to 125 °C
Storage temperature range, Tstg – 65 to 150 – 65 to 150 – 65 to 150 – 65 to 150 °C
Case temperature for 60 seconds, TC FK package 260 °C
Lead temperature 1,6 mm (1/16 inch) from case for 60
J or JG package 300 °C
seconds
Lead temperature 1,6 mm (1/16 inch) from case for 10 D, N, P, or
260 260 260 °C
seconds PW package
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC – .
2. Differential voltages are at IN+ with respect to IN –.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 V, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.
MIN TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX
25°C 3 15 3 6 2 3 3 6
VIO Input offset voltage VO = 0 RS = 50 Ω mV
Full range 20 7.5 5 9
Temperature
α VIO coefficient of input VO = 0 RS = 50 Ω Full range 18 18 18 18 µV/°C
offset voltage
25°C 5 200 5 100 5 100 5 100 pA
IIO Input offset current ‡ VO = 0
Full range 2 2 2 10 nA
25°C 30 400 30 200 30 200 30 200 pA
IIB Input bias current ‡ VO = 0
Full range 10 7 7 20 nA
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
– 12 – 12 – 12 – 12
Common-mode input
VICR 25°C ± 11 to ± 11 to ± 11 to ± 11 to V
voltage range
15 15 15 15
RL = 10 kΩ 25°C ± 12 ± 13.5 ± 12 ± 13.5 ± 12 ± 13.5 ± 12 ± 13.5
Maximum
M i peak
k
VOM RL ≥ 10 kΩ ± 12 ± 12 ± 12 ± 12 V
out ut voltage swing
output Full range
RL ≥ 2 kΩ ± 10 ± 12 ± 10 ± 12 ± 10 ± 12 ± 10 ± 12
Large-signal VO = ± 10 V, RL ≥ 2 kΩ 25°C 25 200 50 200 50 200 50 200
AVD differential voltage V/mV
amplification VO = ± 10 V, RL ≥ 2 kΩ Full range 15 25 25 25
B1 Unity-gain bandwidth 25°C 3 3 3 3 MHz
ri Input resistance 25°C 1012 1012 1012 1012 Ω
Common-mode VIC = VICRmin,
CMRR 25°C 70 86 75 86 75 86 75 86 dB
rejection ratio VO = 0, RS = 50 Ω
Supply voltage
VCC = ± 15 V to ± 9 V,
kSVR rejection ratio 25°C 70 86 80 86 80 86 80 86 dB
VO = 0, RS = 50 Ω
(∆ VCC± /∆ VIO)
Supply current
ICC VO = 0, No load 25°C 1.4 2.8 1.4 2.8 1.4 2.8 1.4 2.8 mA
(per amplifier)
VO1/ VO2 Crosstalk attenuation AVD = 100 25°C 120 120 120 120 dB
† All characteristics are measured under open-loop conditions with zero common-mode voltage unless otherwise specified. Full range for TA is 0°C to 70°C for TL08_C, TL08_AC,
TL08_BC and – 40°C to 85°C for TL08_I.
‡ Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive as shown in Figure 17. Pulse techniques must be used
that maintain the junction temperature as close to the ambient temperature as possible.
TL081, TL081A, TL081B, TL082, TL082A, TL082B
TL082Y, TL084, TL084A, TL084B, TL084Y
JFET-INPUT OPERATIONAL AMPLIFIERS
SLOS081E – FEBRUARY 1977 – REVISED FEBRUARY 1999
Equivalent input
in ut noise f = 1 kHz 18 nV/√Hz
Vn RS = 20 Ω
voltage f = 10 Hz to 10 kHz 4 µV
Equivalent input noise
In current RS = 20 Ω, f = 1 kHz 0.01 pA/√Hz
10 kΩ
–
OUT 1 kΩ
–
VI + VI
OUT
CL = 100 pF RL = 2 kΩ +
RL CL = 100 pF
Figure 1 Figure 2
100 kΩ
– TL081
IN –
C2
OUT
+
C1 500 pF IN + N2
N1
–
IN – N1 100 kΩ
OUT
+
1.5 kΩ
VCC –
Figure 3 Figure 4
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Frequency 5, 6, 7
vs Free-air temperature 8
VOM Maximum peak output voltage
vs Load resistance 9
vs Supply voltage 10
vs Free-air temperature 11
Large signal differential voltage amplification
Large-signal
AVD vs Frequency 12
Differential voltage amplification vs Frequency with feed-forward compensation 13
PD Total power dissipation vs Free-air temperature 14
vs Free-air temperature 15
ICC Supply current
vs Supply voltage 16
IIB Input bias current vs Free-air temperature 17
Large-signal pulse response vs Time 18
VO Output voltage vs Elapsed time 19
CMRR Common-mode rejection ratio vs Free-air temperature 20
Vn Equivalent input noise voltage vs Frequency 21
THD Total harmonic distortion vs Frequency 22
TA = 25°C
VOM – Maximum Peak Output Voltage – V
± 10 ± 10
VCC ± = ± 10 V
VCC ± = ± 10 V
± 7.5 ± 7.5
±5 VCC ± = ± 5 V ±5
VCC ± = ± 5 V
± 2.5 ± 2.5
0 0
100 1k 10 k 100 k 1M 10 M 100 1k 10 k 100 k 1M 10 M
f – Frequency – Hz f – Frequency – Hz
Figure 5 Figure 6
TYPICAL CHARACTERISTICS†
ÎÎÎÎÎ
FREQUENCY FREE-AIR TEMPERATURE
± 15
ÎÎÎÎÎ
± 15
RL = 10 kΩ
VCC ± = ± 15 V
TA = 25°C RL = 2 kΩ
± 12.5
ÎÎÎÎÎ
See Figure 2 ± 12.5
RL = 2 kΩ
± 10 ± 10
TA = – 55°C
± 7.5 ± 7.5
TA = 125°C
±5 ±5
± 2.5 ± 2.5
VCC ± = ± 15 V
See Figure 2
0 0
10 k 40 k 100 k 400 k 1M 4M 10 M – 75 – 50 – 25 0 25 50 75 100 125
f – Frequency – Hz TA – Free-Air Temperature – °C
Figure 7 Figure 8
TA = 25°C TA = 25°C
± 12.5 See Figure 2 ± 12.5
± 10 ± 10
± 7.5 ± 7.5
±5 ±5
± 2.5 ± 2.5
0 0
0.1 0.2 0.4 0.7 1 2 4 7 10 0 2 4 6 8 10 12 14 16
RL – Load Resistance – kΩ | VCC ± | – Supply Voltage – V
Figure 9 Figure 10
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TYPICAL CHARACTERISTICS†
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
1000
700
400
AVD – Large-Signal Differential
Voltage Amplification – V/mV
200
100
70
40
20
10
7
4 VCC ± = ± 15 V
VO = ± 10 V
2
RL = 2 kΩ
1
– 75 – 50 – 25 0 25 50 75 100 125
TA – Free-Air Temperature – °C
Figure 11
LARGE-SIGNAL
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
FREQUENCY
106
VCC ± = ± 5 V to ± 15 V
RL = 10 kΩ
105 TA = 25°C
AVD – Large-Signal Differential
Voltage Amplification – V/mV
104 0°
Differential Voltage
Amplification
Phase Shift
(left scale)
103 45 °
102 90 °
Phase Shift
101 (right scale) 135 °
1 180 °
1 10 100 1k 10 k 100 k 1M 10 M
f – Frequency – Hz
Figure 12
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TYPICAL CHARACTERISTICS†
225 No Signal
C2 = 3 pF No Load
105
TA = 25°C 200
103 125
100
TL082, TL083
102
75
TL081
50
10
25
1 0
100 1k 10 k 100 k 1M 10 M – 75 – 50 – 25 0 25 50 75 100 125
f – Frequency With Feed-Forward Compensation – Hz TA – Free-Air Temperature – °C
Figure 13 Figure 14
I CC ± – Supply Current – mA
1.4 1.4
1.2 1.2
1.0 1.0
0.8 0.8
0.6 0.6
0.4 0.4
0.2 0.2
0 0
–75 – 50 – 25 0 25 50 75 100 125 0 2 4 6 8 10 12 14 16
TA – Free-Air Temperature – °C | VCC ± | – Supply Voltage – V
Figure 15 Figure 16
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TYPICAL CHARACTERISTICS†
10 Output
2
1 0
–2
0.1 Input
–4
0.01 –6
– 50 – 25 0 25 50 75 100 125 0 0.5 1 1.5 2 2.5 3 3.5
TA – Free-Air Temperature – °C t – Time – µ s
Figure 17 Figure 18
24 RL = 10 kΩ
88
20
VO – Output Voltage – mV
87
16
VCC ± = ± 15 V
RL = 2 k Ω
12 CL = 100 pF 86
TA = 25°C
8 See Figure 1
85
4
84
0
–4 83
0 0.2 0.4 0.6 0.8 1.0 1.2 – 75 – 50 – 25 0 25 50 75 100 125
t – Elapsed Time – µ s TA – Free-Air Temperature – °C
Figure 19 Figure 20
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TYPICAL CHARACTERISTICS†
AVD = 10 AVD = 1
0.4
RS = 20 Ω VI(RMS) = 6 V
0.1
30
0.04
20
0.01
10 0.004
0 0.001
10 40 100 400 1 k 4 k 10 k 40 k 100 k 10 400 1k 4k 10 k 40 k 100 k
f – Frequency – Hz f – Frequency – Hz
Figure 21 Figure 22
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
APPLICATION INFORMATION
RF = 100 kΩ
VCC +
–
15 V
3.3 kΩ R1 R2 TL081
Output +
– Input Output
TL081 C3 VCC –
CF = 3.3 µF
+
1 kΩ
– 15 V
R3 R1 = R2 = 2(R3) = 1.5 MΩ
3.3 kΩ C1 C2
C1 = C2 = C3 = 110 pF
9.1 kΩ 2
1 1
f= fo = = 1 kHz
2π RF CF 2π R1 C1
Figure 23 Figure 24
APPLICATION INFORMATION
VCC +
1 MΩ –
TL084 Output A
VCC + +
+
1 µF TL084
– VCC +
Input –
TL084 Output B
100 kΩ 100 kΩ +
VCC +
100 kΩ
VCC +
100 µF 100 kΩ –
TL084 Output C
+
6 sin ωt 1N4148
– 15 V
18 pF 18 kΩ
1 kΩ (see Note A)
18 pF
VCC +
–
VCC+
1/2 88.4 kΩ –
TL082 1/2
6 cos ωt
+
88.4 kΩ TL082
VCC – +
18 pF VCC – 1 kΩ
15 V
1N4148 18 kΩ
88.4 kΩ (see Note A)
APPLICATION INFORMATION
16 kΩ 16 kΩ
220 pF 220 pF
43 kΩ 30 kΩ 43 kΩ 30 kΩ
43 kΩ VCC + VCC +
220 pF VCC + 220 pF VCC +
Input –
43 kΩ
–
43 kΩ
1/4 – 43 kΩ 1/4 –
TL084 1/4 TL084 1/4 Output
+ +
TL084 TL084 B
+ +
1.5 kΩ VCC – 1.5 kΩ VCC –
VCC – VCC –
Output A
Output A Output B
2 kHz/div 2 kHz/div
Second-Order Bandpass Filter Cascaded Bandpass Filter
fo = 100 kHz, Q = 30, GAIN = 4 fo = 100 kHz, Q = 69, GAIN = 16
MECHANICAL DATA
D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.010 (0,25) M
0.014 (0,35)
14 8
0.010 (0,25)
1 7
0°– 8°
0.044 (1,12)
A 0.016 (0,40)
Seating Plane
PINS **
8 14 16
DIM
MECHANICAL DATA
FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER
28 TERMINAL SHOWN
NO. OF A B
18 17 16 15 14 13 12
TERMINALS
** MIN MAX MIN MAX
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
4040140 / D 10/96
MECHANICAL DATA
J (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE
14 PIN SHOWN
PINS **
14 16 18 20
DIM
0.100 (2,54)
0.020 (0,51) MIN A
0.070 (1,78)
0.100 (2,54)
0°–15°
0.023 (0,58)
0.015 (0,38) 0.014 (0,36)
0.008 (0,20)
4040083/D 08/98
MECHANICAL DATA
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE PACKAGE
0.400 (10,20)
0.355 (9,00)
8 5
0.280 (7,11)
0.245 (6,22)
1 4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.020 (0,51) MIN
0.290 (7,37)
0.063 (1,60)
0°–15°
0.015 (0,38) 0.023 (0,58)
0.015 (0,38)
0.100 (2,54) 0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
MECHANICAL DATA
N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE
16 PIN SHOWN
PINS **
14 16 18 20
DIM
0.260 (6,60)
0.240 (6,10)
1 8
0.070 (1,78) MAX
0.310 (7,87)
0.035 (0,89) MAX 0.020 (0,51) MIN
0.290 (7,37)
Seating Plane
0.100 (2,54)
0°– 15°
0.021 (0,53)
0.010 (0,25) M 0.010 (0,25) NOM
0.015 (0,38)
4040049/C 08/95
MECHANICAL DATA
P (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE
0.400 (10,60)
0.355 (9,02)
8 5
0.260 (6,60)
0.240 (6,10)
1 4
0.310 (7,87)
0.020 (0,51) MIN
0.290 (7,37)
Seating Plane
0.021 (0,53)
0.010 (0,25) M
0.015 (0,38) 0.010 (0,25) NOM
4040082 / B 03/95
MECHANICAL DATA
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0,30
0,65 0,10 M
0,19
14 8
0,15 NOM
4,50 6,60
4,30 6,20
Gage Plane
0,25
1 7
0°– 8°
A 0,75
0,50
Seating Plane
PINS **
8 14 16 20 24 28
DIM
4040064 / E 08/96
MECHANICAL DATA
U (S-GDFP-F10) CERAMIC DUAL FLATPACK
0.250 (6,35)
0.246 (6,10)
0.006 (0,15)
0.004 (0,10)
0.080 (2,03)
0.050 (1,27) 0.045 (1,14)
0.026 (0,66)
0.300 (7,62)
0.350 (8,89) 0.350 (8,89)
0.250 (6,35) 0.250 (6,35)
0.019 (0,48)
1 10
0.015 (0,38)
0.050 (1,27)
0.250 (6,35)
5 6
0.025 (0,64)
0.005 (0,13)
1.000 (25,40)
0.750 (19,05)
4040179 / B 03/95
MECHANICAL DATA
W (R-GDFP-F14) CERAMIC DUAL FLATPACK
0.007 (0,18)
0.004 (0,10)
0.080 (2,03)
0.045 (1,14) 0.045 (1,14)
0.026 (0,66)
0.280 (7,11)
0.360 (9,14) 0.255 (6,48) 0.360 (9,14)
0.240 (6,10) 0.240 (6,10)
1 14 0.019 (0,48)
0.015 (0,38)
0.050 (1,27)
0.390 (9,91)
0.335 (8,51)
0.025 (0,64)
0.015 (0,38)
7 8
1.000 (25,40)
0.735 (18,67)
4040180-2 / B 03/95
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.