Вы находитесь на странице: 1из 19

1.

Cracks may occur in a hot section components of a turbine engine if they are marked during inspection with
a. A lead pencil b. chalk c. layout dye d. all of the above
2. What is the first engine instrument indication of a successful start of a turbine wheel
a. A decrease in the EGT b. a decrease in the EPR c. a rise in the fuel flow d. a rise in the EGT
3. What must be done after the fuel control unit has been replaced on a turbine engine
a. Retime the engine b. recalibrate the fuel nozzle c. recheck the flame pattern d. retrim the engine
4. Where do stress rupture cracks usually occurs on turbine blades of turbojet engine
a. Across the blade root, parallel to the fir- tree b. Along the trailing edge, parallel to the edge
c. Along the leading edge parallel to the edge d. Across the leading edge or trailing edge at a right angle to the edge length
5. Reduced blade vibration and improve air flow characteristics in gas turbine are brought out by
a. Shrouded turbine rotor blade b. fir- tree blade attachment c. impulse turbine rotor blade d. both a &b
6. When turbine blades are subjected to excessive temperature what type of failure can occur
a. Compression and torsion b. bending and torsion c. torsion and tension d. stress rupture
7. Dirty compressor blade in a turbine engine could result in
a. High EGT b. high RPM c. low EGT d. low RPM
8. What should be done if a turbine engine catches fires during starting
a. Turn off the fuel and continue cranking b. disengage starter immediately
c. Continue starting attempt to blow out fire d. place power lever in increase to exhaust fuel fumes
9. When trimming gas turbine engine the FCU is adjusted to
a. limit idle RPM and maximum speed
b. Both a&b b
10. If a blade of particular metal propeller is shortened because of damage to the tip the remaining blade must be
a. Ground at the shank to balance the weight b. returned to the manufacturer for alteration
c. Reduced to confirm with the shortened blade d. none
11. Propeller blade are measured from the
a. Hub centerline b. blade base c. blade tip d. index mark on the blade shank
12. How can a steel propeller hub be tested for cracks
a. By anodizing b. by magnetic particle inspection
c. By etching d. by die penetrant method
13. Hot spot on the tail cone of a gas turbine engine are the indication of a malfunctioning fuel nozzle or a
a. Faulty igniter plug b. faulty combustion chamber c. improperly installed tail cone d. loose inlet guide vane
14. Severe rubbing of turbine engine compressor blades will usually cause
a. Galling b. scoring c. pitting d. cracking
15. Why does a turbine engine require a cooling off period before engine shut down
a. To allow the turbine assembly to cool before the case contracts around it
b. To avoid seizure of the engine bearing
c. To burn off excess fuel ahead of the fuel control
d. All of the above
16. Vibration monitoring of Engine is accomplished through
a. Pyrometer b. Accelerometer c. Thermal sensors d. Pitch/Roll Sensors
17. RDT of the Engine means
a. Time taken to come to rest after FSF valve is closed b. Absence/presence of rubbing inside the engine c. Condition
monitoring of the Engine d. None of the above
18. Trouble Shooting is
a. Refers to procedure for locating the fault b. Quick and accurate diagnosis of a fault c. Prevents unnecessary
removal of components d. All are correct
19. Adjustment of Engine means
a. Idling/Max RPM to designed values b. Acceleration/Deceleration timings c. Compressor air bleed
values d. All the above

20. Under what condition the gas turbine engine trimming will be most accurate
a. High wind and high humidity b. high moisture and low wind c. no wind and low humidity d. none
21. The high velocity stream of turbulent air behind an operating aircraft is
a. Wick b. bake c. wake d. bike
22. The thumb rule of hazard area behind a Turbo Jet Engine while it is developing take off thrust is
a. 100ft b. 150 ft c. 200ft d. 250 ft
23. A hot start is normally caused by a mixture that Is
a. Too weak b. Too rich c. Less weak d. Less rich
24. A sequence of events that consists of an engine start, take off, landing and shut down is called
a. Operating hours b. operating cycle c. flying hours d. total hours
25. Repair carried out at on wings are called
a. Minor repair b. Major repair c. Bench repair d. Overhaul
26. Overhaul is carried out
a. At fixed period’s b. After major defect c. After heavy landing d. after lightning strike
27. The reconditioning of the surface with the help of special files, emery paper or carborrundum stone to remove dents, nicks, or scratches
which are within limit on a compressor blade is called
a. Beading b. Blending c. Blending d. Bleaching
28. The vibrations and stresses produced by gas turbine engine are increases as
a. The square of the rotational speed b. the same as the rotational speed
c. The three times of the rotational speed d. the four times of the rotational speed operate fire
29. The methods of measuring and correcting unbalance are
a. Single plane balancing b. two plane balancing c. three plane balancing d. single and two balancing
30. The single plane balancing is known as
a. Static b. Dynamic c. Both a & b d. none of the above
31. Cleaning agent used for degreasing is
a. Kerosene b. Tri chloro ethane c. white spirit d. Benzene
32. Characteristics of P& D valve
a. Dump valve is spring loaded close b. pressurizing valve is spring loaded open
c. Pressurizing valve limits starting fuel to primary manifold d. all of the above
33. Oil pressure continuously fluctuates
a. Indicates is faulty b. pressure relief valve is sinking and contaminated
c. Both a and b Oil check valve setting is improper
34. Compressor blade is loose fit due to
a. Reduce vibration stress b. Ease of removal c. Temperature compensation d. All of above
35. Last chance filter in the oil system screen type
a. Cleared during engine overhaul b. prevent clogging of jet
c. Cleaner during 100hrs inspection d. Both 1&2
36. Smooth repair of rugged edge or surface into the contour surrounding area is called
a. Blend b. bow c. burning d. burr
37. What are the positions of pressurizing and dump valve when engine is shut down
a. Pressurization valve and dump valve open b. Pressurization valve closed and dump open
c. Pressurization valve open and dump closed d. Pressurization valve closed and dump closed
38. A condition known as hot streaking in turbine engine is caused by
a. A partially clogged fuel nozzle b. Misaligned combustion liner
c. Uneven burner can cooling d. Excessive fuel flow
39. Mark the correct and statement
a. Scavenger pump is centrifugal type of the larger capacity b. Pr pump is centrifugal type
c. Scavenger pump capacity is smaller than pressure pump d. Both pump are gear type
40. An ignition unit may be supplied with alternative current and operated by
a. Trembler mechanism b. a transistor chopper circuit c. transformer d. None.
41. Engine pressure ratio is the ratio of
a. Turbine discharge pressure to engine inlet pressure b. Turbine inlet pressure to outlet pressure
c. Compressor outlet pressure to compressor inlet pressure d. Both b and c are correct
42. To ensure continued effectiveness of the engine lubricant, two procedures are employed
a. Oil analysis and glittering b. oil analysis and flattering c. Oil analysis and filtering d. spilling and pouring
43. Purpose of inlet guide vane is
a. To direct airflow to the first stage compressor at high velocity b. To direct airflow at high pressure
c. To direct air flow at the proper angle to the compressor inlet d. To increase thrust
44. Normal function of the exhaust nozzle is to
a. To control the exhaust nozzle flame b. To control the turbine inlet temperature
c. To control the velocity and temperature of the exhaust gas d. To control the pressure and temperature of the exhaust gas
45. Prist is an additive used in jet fuel
a. To prevent fuel icing b. to prevent bacterial contamination
c. To prevent fuel solidification d. both a and b are correct.
46. The amount of force to be exerted on a push pull rod determines
a. Its length and wall thickness b. its diameter and wall thickness
c. The way it is operated d. none of the above.
47. In controls turnbuckles are used for
a. Preventing the turbine movement of control cable b. To control horizontal movement of the control cable
c. For adjusting the tension and length of cable d. Both A and B are correct
48. Controls used for operation of throttle and propeller is
a. Flexible push pulls control b. cable and pulley control c. Push pull tube control d. vernier push pull control
49. Wet motoring is employed for checking
a. Oil system components b. fuel system component c. air system d. bleed valve operation
50. Check performed to ensure that the engine will achieve take off power on a hot day with exceeding rpm
a. Idle check b. pressure ratio check c. power assurance check d. thrust augmentation check
51. Type of combustor mounted on JT8D-9A engine is
a. 9 annular type b. 8 can type c. 7 can annular type d. 9 can annular type
52. During engine testing essential parameters to be checked includes
a. Thrust b. exhaust total pressure c. ambient air temperature d. all the above
53. If crack is observed in propeller hub then
a. Weld the area b. machine the area c. reject hub d. both a and b
54. Air inlet duct provided in a gas turbine engine is to
a. Prevent entry of foreign object b. accelerate the incoming airflow
c. Provide constant flow of subsonic air with a minimum of disturbances d. both b and c are correct.
55. For an aircraft flying at supersonic speed the air intake
a. Must have multiple inlet b. should be of convergent type
c. Should be of divergent type d. should be of convergent – divergent type
56. Compressor stall is caused by
a. Low angle of attack airflow through the first stage of compressor b. High angle of attack airflow through the first stage of turbine
c. Vary rapid engine declaration d. Blocked combustion chamber
57. Exhaust pipe is subjected to high gas temperature thus it is made of
a. Forged aluminum alloy b. stainless steel c. nickel or titanium alloy d. cadmium alloy
58. Turbine fuel must be
a. Stable over wide temperature range b. corrosion resistant
c. Capable of vaporizing quickly d. only a& b are correct
59. The freezing point of turbine fuel range from
a. -20° C to -30° C b. -40° C to -60 ° C c. -60° C to -70° C d. 40°C to 60° C
60. Gasoline and Kerosene are used as turbine engine fuel how do they compare in heat energy
a. Gasoline has more heat energy per gallon than kerosene b. Kerosene has more heat energy per gallon than gasoline
c. Gasoline and kerosene have the same heat energy per gallon d. None of the above.
61. Fuel – cooled oil cooler is located between the
a. Oil pump and outlet of the fuel filter b. Fuel pump and inlet to the fuel filter
c. Oil tank outlet to the fuel tank inlet d. Oil pump inlet to the fuel tank outlet.
62. What causes the fuel divider valve to open in a turbine engine duplex nozzle
a. Thermostatically controlled heat from the combustion section b. Fuel pressure
c. By the dump valve d. electrically operated solenoid
63. Pneumatic starter advantage
a. It requires small amount of air b. it is self sufficient
c. It has light weight to torque d. it produce high voltage
64. The function of an APU air inlet plenum is to
a. Increase the velocity of air before entering to the compressor b. Decrease pressure of the air before entering to the compressor
c. Increase the pressure of air entering in to the compressor d. Stabilize the pressure of the air before it enters the compressor
65. In air turbine starter low pressure high volume air is supplied from
a. On board APU b. ground power unit c. air- bleed from an operating a/c engine d. any of the above.
66. A gas turbine starter is KW 367
a. Is a selfsustined miniature turbine engine B. It has its own fuel and lubrication system
c. it has its own starting and ignition system D. All the above
67. Fuel to APU is taken from which source
a. Aircraft fuel system b. external fuel tank c. auxiliary tank d. from refueler
68. One of the following is not a factor affecting the operation of an automatic FCU unit used in GT engines. Which one?
a. Air density compressor inlet b. Mixture control position c. Throttle position d. Aircraft altitude
69. Which statement below is true
1. Kerosene type fuel consist of heavier hydrocarbon fraction
2. Wide cut gasoline consist of heaver hydrocarbon
3. Kerosene type gasoline is more dense than wide cut gasoline
4. Wide cut gasoline is more dense than kerosene type gasoline
a. No.1 is true b. No.2 is true c. No.1&3 are true d. No.3 is true
65. in oil cooler
a. The thermostat valve prevent oil motion in to it when oil is hot
b. Thermostat valve does not control oil motion
c. Thermostat valve prevent oil mitio in to it when oil cold
d. Both a & b are correct
66. The cut made in the process of repairing the fan blade are termed as
a. Spy back cut b. Fly back cut c. Shingling cut d. None of the above
67. When a new fixed pitch propeller has been installed and operated the hub should always inspected for tightness
a. After the first flight b. After 25 hrs flying c. After 50hrs of flying d. All the above
68. During propeller blade local etching cracks on propeller blade will appear as
a. Black stains b. Gray stain c. Brown stain d. White stain
69. During propeller local etching procedure faws such as cold shut and inclusion will appear as
a. Fine blue line b. Fine brown line c. Fine black line d. Fine red line
70. Purpose of local etching is
a. It determines with a minimum removal of metal whether or not shallow crack have been removed
b. It exposes small cracks that might not be visible otherwise
c. Both A&B
d. It can glue the damaged parts effectively
71. Which of the following is not a factor in the operation of an a automatic FCU unit used on GT Engines?
a. Mixture control position b. Throttle position c. Compressor RPM d. Compressor inlet air density QB1105

72. The EGT indicators in flight deck shows 12A 10-56


a. The average temperature measure by individual thermocouples
73. The exhaust temperature is proportional to
a. ----------- b. the turbine inlet temperature 12A 10-55
74. The gas turbine engines where the cobalt chloride silica gel is used
a. Humidity indicator envelops 12A 8-25
75. The engine should be operated with in – hrs of pre oiling
a. ---- b.---- c. 4 hours 12A 8-13
76. Thrust produced by a turbojet or turbo fan engine when the engine is static or not moving
a. Gross thrust -------- 12A 1-57
77. The method of defecting invisible crack and other defecting invisible crack and other defects in jerromagnetic material such as iron and
steel 12A 10-8
a. Magnetic pa—inspection
78. A change in color locally causing noticeably different appearance from the surrounding area
a. ---- b. Stain
79. A condition of turbine engine operation when the fire unintentionally goes out
a. Flame out 12A 4-12
80. What are the load carried by the forward isolator engine mount
a. Vertical and axial loads 12A 8-22
81. The engine must be retrimmed after
a. A fuel control unit is replaced 12A 8-21
82. The turbine engine where the --- chloride silica gel is used
a. Humidity indicator envelope 12A 8-28
83. Which are classified the temporary storage
a. Aircraft and engine that is not flown from 30-90 days
84. What are the agents used for degreasing the engine parts
a. Emulsion type --------
85. For checking the resistance of a thermocouple harness which unit can be used
a. JETCAL analyses/ trimmer system
86. The unit of the engine which is adjusted to trim the engine to obtain maximum thrust output of the engine when desired
a. Fuel control unit
87. The engine must be retrimmed after
a. A fuel control unit is replaced
88. What are the loads carried by the forward isolators engine mount
a. Vertical and axial loads
89. Tachometer is usually calibrated in
a. Percent RPM
90. A series of blunt depression in a surface
a. Peening
91. Fuel flow in turbine engine in measured in
a. ------- b----- c. lbs/ br instead of gallons
92. The exhaust temperature in proportional to
a. The turbine inlet temperasture
93. Tacho meter is usually caliberted in
a. Present RPM
94. For checking the resistance of a thermo couple harness which unit can be used
a. --- b. JETICAL analyse/ trimming system
95. Fuel flow instruments indicate the
a. Fuel flow in pounds per hour
96. In a GTE Aircraft how much reverse thrust is usually required for minimum braking needs?
a. At least 50% of the thrust b. 100% of the thrust c. 75% of the thrust d.just 25% of the thrust QB1113
97. Which of the following can cause fan blade shingling in a GTE?
a. Excessive mass flow rate b. Engine over temperature c. rapid throttle movements d.FOD in the Compressor QB1124
98. Hot streaking in an engine is caused by?
a. Uneven burner can cooling b. Excessive fuel flowc. Partially clogged fuel nozzle d. Misaligned combustor lining QB1170
99. What type of main bearing oil seal is used on a GTE?
a. Syliconnylon b. Teflonsynthetic c. Labyranth or Carbon d. Labyranth or siliconQB1164

100. A condition caused by a rubbing action between two parts under light pressure that results in wear
a. Chaffing
101. In which program allows an oil sample to be analyzed and searched for vthe presence of minute metallic element
a. Spectrometric oil analysis program
102. In the connections of thwe RPM check are the instrument cable and aircraft tachometer ststem lead—indicator
a. Tachometer indicator
103. In a corrosion preventive, bags of silica gel are placed around and inside various accessible parts of a stored engine it is also used in clear
plastic plugs called
a. Dehydrator plugs
104. What are the agents used for degreasing the engine parts
a. Emursion type cleaness or chlorinated solvents
105. In gas turbine engine, where the cobalt chloride silica gel is used
a. Humidity indicator envelopes
106. What is thermocouple write about thermocouple instrument
107. Before using any pre oiling method what should be removed from the cylinder
a. Remove one spar plug from each cylinder
108. The engine should be operated within how many hours of pre oiled
a. Within 4 hours
109. To prevent failure of the engine bearing during initial start, the engine should be
a. Pre- oiled
110. A series of blunt depressions in a surface
a. Peening
111. The exhaust temperature is proportional to
a. The turbine inlet temperature
112. The engine is installed – after with the prop shaft approximately
a. 39degree above horizontal
113. If only small pareticles are found that are similar in nature to flings
a. Drain the oil system and refill it
114. Corrosion preventive components are
a. Petroleum based product that forms a wax line film over the metal
115. Cobalt chloride treated silica gel is used in
a. Humidity indicator envelopes
116. SOAP allows an oil sample to be analyzed and search for the presence of
a. Minute metallic elements
117. The exhaust temperature is proportional to
a. The turbine inlet temperature (12A-10-55)
118. In gas turbine engines where the cobalt chloride silica gel is used
a. Humidity indicates envelops (12A -8-25)
119. The engine should be operated within – of pre oiling
a. 4 hour 12A 8-30)
120. A mechanical device which produces forward thrust by forcing the -----
a. Turbine egine power plant 279
121. Relatively small – are of the engine provides
a. A straight through flow system power plant 280
122. The amount of thrust developed by the jet nozzle compared with the energy supplied to it ina usable form
a. Propulsive efficiency power plant 286
123. Which type of propelling nozzles used where the super sonic speed are –
a. Convergent, divergent power plant 281
124. Vibration monitoring of Engine is accomplished through QB 1180
a. Pyrometer b. Accelerometer c. Thermal sensors d. Pitch/Roll Sensor
125. RDT of the Engine means
a. Time taken to come to rest after FSF valve is closed b. Absence/presence of rubbing inside the engine c. Condition
monitoring of the Engine d. None of the above

126. Fuel flow in turbine engine is measured in


a. Ibs/br instead of gallons 12A 10-58
127. Tachometer is usually calibrated in
a. Percent RPM 12a 10.56
128. HALF SECTION INSPECTION INTERVALS VERY WIDELY ON
a. TBOC (time between overhaul ) and engine service experience kroes 10
129. Briefly explain engine trouble shooting (12A 10-36)
130. Configuring on instrument to provide a useful source a simple within an acceptable usage process is called
a. Calibration
131. When a maintenance is caused out in a machine as – the – of the user to correct its operation is called
a. Corrective maintenance
132. The measure of power producer by a turbo prop engine is called
a. ESHP
133. The oil pressure indicator usually shows
a. Engine oil pump discharge pressure
134. The step by step procedure used to determine the use of a given salt and then select the base and quicker solution process is called
a. – shooting
135. The clean and flash out liquids -- --- --- line to prevent the build up explosive mixture is called
a. Purging
136. Which statement is correct about urging
a. Inspect bell cracks --- ---- crank, --- corrosion
b. Inspect – end ---- --- the number of --- --- after the final adjustment
c. Inspect cable during -- --- and cable --- --- proper position and tension
d. All are correct
137. The color of dehydrator undle 60%of relative humidity
a. Natural white color
138. The humidity indicator envelops have
a. Co balt chloride – silica gel
139. The light mixture of – preventive components is available in
a. 3 ----
140. Name four turbine engine instrument and explain it
141. The EGT indicates in flight deck shows
a. The average temperature measured by individual thermocouples 12A 10-56
142. What are the leads carried by the forward isolator engine mount
a. Vertical and axial loads 12A 8-22
143. The engine must be retrimmed after
a. A fuel control unit is replaced 12A 8-21
144. Tachometer is usually calibrated in
a. Percent RPM 12a 10-56
145. FUEL FLOW IN TURBINE ENGINE MEASURED IN
a. Ibs/ bs instead of gallons 12A 10-58
146. Which types of propelling nozzle is used where the supersonic speed are encountered
a. Convergent & divergent nozzle PPT P-28
147. When starting a GTE, the starter should generally be disengaged
a. When engine lights off b. When ignition and and fuel systems are activated c. Only when engine has reached idle RPM
d. after the Engine has reached self sustain speed QB 1077
148. Engine cranking is done to
a. Remove dirt/dust entrapped in the Compressor b. Clear trapped fuel or grease in the exhaust pipe c. To check any
obstructions /fouling of Compressor rotor QB1085
149. During trimming the Engine the Aircraft must be facing into the wind . However if the wind speed is excessive it is likely to cause
a. False low exhaust gas Temperature reading b. Trim setting resulting in Engine over speed c. False high compression
and turbine discharge pressure resulting in low trim d. Both A and B are correct QB 1099
150.

151. Before shutting down the Engine why does it require a cool off period?
a. To avoid seizure of Turbine Bearings b. To burn off any residual fuel c. To allow all the lubricating oil to return to the
sump d. To allow the Turbine wheel to cool before the case around it contracts QB1083
152. A series of blunt depression in a surface
a. Peening 12A 10-4
153. The engine should be operated within—of pre oiling
a. 4 hours 12A 8-30
154. An engine start or attempted start, which results in the turbine temperature exceeding the specified limits
a. Hot start kroes &wild 730
155. Which type compressor in a gas turbine engine that is made in the form of a disk- type impeller
a. Centrifugal flow compressor kroes glossary 728
156. Explain trouble shooting on turbine engine 12A 10-60
157. The EGT indication in flight deck shows
a. The average temperature measured by individual thermocouple 12A 1056
158. The engine must be retrimmed after
a. A fuel control unit is replaced
159. For checking the resistance of a thermo couple harness which unit can be used
a. JETCAL analyzer / trimming system kroes 531-532
160. A change in color locally using noticeably different appearance from surrounding area
a. Stain 12A 10-3
161. What are the agents used for degreasing the engine parts
a. Emulsion type cleaners on chloride solvent 12A 10-49
162. In gas turbine engine, where the cobalt chloride silica gel is used to
a. Humidity indicator envelopes 12A 8-25
163. What is the purpose of an oil pressure indicator
a. It shows the engine oil pump discharge pressure 12A 10-58
164. Fuel flow in turbine engine is measured in
a. Ibs/hr instead of gallons 12A 10-58
165. Tachometer is usually calibrated in
a. Percent RPM 12a 10-56
166. A series of blunt depressions in a surface is called
a. Peening 12A 10-4
167. Fuel flow in turbine engine measured in
a. Ibs /hr instead of gasoline 12A 10-56
168. The engine should be operated within of pre oiling
a. 4 hrs 12A 8-30
169. Which type of propelling nozzle used where the supersonic speed are -------
a. Convergent divergent PP 2-81
170. A change in color locally causing noticeably different appearance from the surrounding area
a. Stain 12A 10-5
171. For checking the resistance of a thermo couple harness which unit can be used
a. Jet cal analyzer trimmer system kroes 531- 532
172. Which unit trimmed to adjust the engine to obtain maximum thrust o/p of engine when desired
a. Fuel control unit 8-21
173. In gas turbine engines where the cobalt chloride silica gel is used
a. Humidity indicates envelops 12A 8-28
174. The engine must be retrimmed after
a. A fuel control unit is replaced 12A 8-21
175. A series of blunt depressions in a surface
a. Peening 12A 10-4
176. Explain spectrometric oil analy30
177. s programme 12A 6-21
178. Fuel flow in turbine is measured in
a. Ibs/ br instead of gallons 12A 10-58
179. Tacho meter is usually calibrated in
a. Percent rpm 12A 10-56
180. The engine should be operated within 4 hours of
a. Pre ceiling 12A 8-30
181. The exhaust temperature is --- to
a. The turbine inlet temperature 12A 8-22
182. The gas turbine engine where the cobalt chloride silica gel is used
a. Humidity indicates envelope 12A 8-25
183. The engine must be--- after the fuel control unit is replaced
a. Retrimmed 12A 8-21
184. A sharp as roughed projection of metal – resulting from machine processing
a. Burr 12A 10-3
185. Reciprocating piston aircraft engine can be repaired by a
a. Top overhaul 12A 10-2
186. A displacement of material beyond the normal --- or surface
a. Upsetting 12A-10-4
187. Explain about some visual inspections any 5
1. Abrasion
2. Brenellinbg
3. Gauging
4. Galling
5. Inclusion
6. Scaffing
7. Scratches
8. Upretting
188. The engine should be never trimmed when
a. Icing – exist 12A 8-25
189. Which type of – are used in secure the engine mounts to –
a. Special heat- treated -- -- 12A 8-24
190. ---- is actually engine pressure ratio indicating
a. Thrust developed by turbo fan engine 12A 10-56
191. Mark the correct statement
a. Turbo props usually fitted with a torque meter measures torque applied to a shaft turned by the gas generator and power
turbines of the turbine engine 12A 10-56
192. What is the purpose of tachometer 3 choose the correct answer
a. Monitor RPM under normal condition, engine start to indicate an over speed condition 12A 10-56
193. Which device is used to indicate the average temperature measured by the individual thermo couples
a. EGT indicator 12A 10-56
194. The section it can engine mount where the engine is attached is known as
a. Engine mount ring 12A 8-24
195. Gas turbine engine speaks are measured by what
a. Engine RPM 12A 8-25
196. What should do after when the fuel control unit is replaced
a. The engine should be trimmed 12A 8-24
197. When relative humidity is less than how much percentage which the corrosion – net take place
a. 30% 12A 8-25
198. Write short notes on turbine engine instruments 12A 55,26,57
199. Breaking away of pieces of material that is usually caused by excessive stress concentration or careless handling
a. Chipping 12A 10-3
200. Tachometer is usually calibrated in
a. Present RPM 12A 10-56
201. Most turbine engine mounts are made of stainless steel
a. Stainless steel
202. Full flow in turbine engine is measured in
a. Lbs/hr instead of gallons 9A 10-58
203. A change in color, locally causing a noticeably different appearance from the surrounding area
a. Strain 12A 10-4
204. The section of an engine mount where the engine is attended is known as
a. Engine mount ring 12A 8-24
205. Which device is used to indicate the average temperature measured by the individual thermo couples
a. EGT indicator 12A 10-56
206. The engine should be never trimmed when
a. Icing condition exist 12A 8-25
207. Which types of bolts are used to secure the engine mounts to aircraft
a. Special heat treated steel bolts 12A 8-24
208. When relative humidity is less than
a. 30 percentage the corrosion does not take place 12A 8-25
209. Write short note on turbine engine instruments 12A 10-55, 56,57
210. The turbine engine mounts are made of
a. Stainless steel 12A 8-24
211. Fuel flow in turbine engine is measured in
a. Lbs / hr instead of gallons 12A 10-58
212. A area of roughened scratches of marks usually caused by foreign matter between moving parts of surfaces
a. Abrasion 12A 10-3
213. What are the agents used for degreasing the engine parts
a. Emulsion type cleaners or chlorinated solvents
214. In gas turbine engines, where the cobalt chloride silica gel is used
a. Humidity indicator envelopes 12A 8-25
215. Breaking away of pieces of material, that is usually caused by excessive stress concentration or careless handling
a. Chipping 12A 10-3
216. Tachometer is usually caliberated in
a. Percentage RPM 12a 10-56
217. IN AN AXIAL COMPRESSOR ENGINE, WHAT IS THE MAIN PURPOSE OF A TACHOMETER
a. Monitor the RPM settings on engine start and indicate over speed conditions 12A 10-56
218. A change in color locally causing a noticeably different appearance from the surrounding area
a. Strain 12A 10-4
219. What is the purpose of an oil pressure indicator
a. It shows the engine oil pump discharge pressure 12A 10-58
220. --- is employed to determine the degree of wear for parts of the engine where moving surfaces are in contact with other surface
a. Dimensional inspection kroes 250
221. Process of overseeing maintenance resource so that organization does not experience down time from broken equipment or waste
money on inefficient maintenance procedure
a. Maintenance management note
222. To clean and fresh out liquids from tanks or lines to prevent built up of explosives mixture with help of nitrogen, carbon dioxide or helium
used
a. Purging note
223. The time taken by a turbine in a gas turbine to come to a complete half after the engine has been switched OFF and it is one of the
indicators of the state of health of an engine
a. Rundown time (spool down time) note
224. – is a method used by aircraft operators to test the health of aircraft engines by performing frequent laboratory testing of the engine oil
a. Spectrometric oil analysis program SOAP NOTE
225. – allows an aircraft to operate autonomously without reliance on ground support equipment such as a ground power unit, an external air
conditioning unit or a high pressure air start cart
a. Auxiliary power unit or APU kroes 479
226. --- produced by gas turbine engines is compressed air that is taken from the compressor stage of those engine, which is upstream of the
burning system
a. Bleed air note
227. A suspension of small globules of one material in another when the two materials will not mix
a. Emulsion
228. Maintained task performed to identify isolate and rectify a fault so that the failed equipment machine, or – can be restored to an
operational condition within tolerance or limit established for in service operations
a. Corrective maintenance break down maintenance note
229. An inspection is needed to determine the integrity of the components in hot section of the engine asuch as turbine inlet guide vanes,
turbine wheels, etc
a. Hot section inspection kroes 509- 510
230. Draw a neat diagram of typical EGT program during the starting procedure and explain it
231. The detection of fault indications and the isolations of the fault or faults causing the indications
a. Trouble shooting kroes 532
232. Fuel flow instruments indicate the fuel flow in pounds per hour
a. 16/hr 12A 10-58
233. A series of blunt depressions in a surface
a. Peening 12A 10-4
234. In case of engine mounts which bolt supports the weight of the engine which aircraft is on ground
a. Upper bolt 12A 8-22
235. What are the loads carried by the forward isolate engine mounts
a. Vertical and axial load 12A 8-22
236. In gas turbine engines where the cobalt chloride silica gel is used
a. Humidity indication envelops 12A 8-25
237. Fuel flow in turbine engine is measured in
a. Ibs/ br instead of gallons 12A 10-58
238. Tacho meters is usually calibrated in
a. Percent RPM 12A 10-56
239. What are the agents used for degreasing the engine parts
a. Emulsion type cleaners or chlorinated solvents 12A 10-49
240. For checking the resistence of a thermocouple harness which unit canbe used
a. JETCAL ANALYSIS / trimmer system kroes 531-532
241. What are the procedures carried on trouble shooting 12A 10-60
242. Most aircraft equipped with reciprocating engines uses an engine mount structure made of
a. Welded steel tubing 12A 8-23
243. The engine mounts ar usually seared to the aircraft by
a. Special heat treated steel bolt 12A 8-25
244. Surface damage due to excessive heat usually caused by improper fit
a. Burning 12A 10-3
245. A sharp or roughned projection of metal usually --- from machine processing is called
a. Bur 12A 10-3
246. An area any roughened scratches or marks usually caused by foreign matters between moving parts or surface
a. Abrasion 12A 10-3
247. What are agents used for decreasing the engine parts
a. Emulsion type cleanser or chlorinated solvent 12A 10---
248. The gas turbine engine where the cobalt chloride silica gel is used
a. Humidity indicator envelops 12A 10-55
249. For checking the resistance of a thermo couple hammer which can be used
a. JETCAL analysis / trimmer stgastem kroes 531-531
250. Tachometer is usually caliberated in
a. Percent RPM 12A 10-56
251. Calliberation of tachometer is done in
a. % rpm 12A 1056
252. When a series of blunt depressions found in a surface it is
a. Peening 12A 10-4
253. Condition caused by a rubbing action between two parts in low pressure that causes wear
a. Chaffing 12A 10-3
254. Fuel flow indicator shows reading in
a. Pounds /hr lb/hr 12A 10-58
255. Component that extend from wings on many aircraft where the engines are mounted in streamlined housing is called
a. Nace---- 12A 10-40
256. A change in color usually using noticeably different appearance from surrounding area
a. Stain 12A 10-3
257. Vibration analysis , lubrication analysis, acoustic emission, ultrasonic testing (ect) comes under
a. Condition monitoring kroes
258. Generally transducer is used to transfer oil pressure in to an electrical signal to be read by the flight deck instrument
a. Transducer 12A 10-56
259. Oil pressure indicates
a. Engine oil pump discharge pressure 12A0-58
260. Turbine engine mounts are mostly made of 12A 8-24
a. Stainless
261. The detection of fault indicators and the isolation of the faults or faults causing the indication is known as
a. Trouble shooting kroes 532
262. If an aircraft not to be flawn for over 20 days or is removed from the aircraft for extended time it is stored as
a. An indefinite storage 12A 8-25
263. An area of roughened scratches or marks usually caused by foreign matter between moving parts or surface
a. Abrasion 12A 10-3
264. Condition caused by a rubbing action between two parts under light pressure that results in ---
a. Chafing 12A 10-3
265. Partial separation of material usually caused by vibration overloading internal, stresses, defective assembly or---
a. Crack 12A 10-3
266. The unit of the engine which is adjusted to from the engine to obtain maximum thrust output of the engine when desired
a. Fuel control unit 12A 8-21
267. The maintenance that includes the periodic and recurring inspection that must be made in accordance with the engine section of the
aircraft maintenance schedule
a. Scheduled maintenance kroes 518
268. The maintenance that covers work necessisted by occurrence that are not normally selected to time limits
a. Unscheduled maintenance kroes 518
269. A change in ideas locally censing noticeably different appearance from the surrounding area
a. Starin 12A 10-3
270. Most engines had specialized no of – they could operate before they needed to be over--. This period is known as
a. Time between over-- kroes p-523
271. Explain briefly about to control analyzer and list out its purpose kroes 5-3
272. The rpm check circuit in the analyser is used to read engine speed during engine – run-up with an accuracy of -- ----
a. ± 0.1 % 12A 10 -66
273. In which program allows an oil sample to be analyzed and searched for the presence of minute metallic elements
a. Spectrometric oil analysis program 12A 6-21
274. The engine is installed facing after with the propeller shaft approximately how many degree above horizontal
a. 39 degree above horizontal 12A 8-23
275. In which indicator is an indication of the thrust being developed by a turbo fan engine and is used to set power for take off on many types
of aircraft
a. Engine pressure ratio indicator 12A 10-56
276. The EGT indicator in the flight deck shows the average temperature measured by
a. Thermocouples 12A 10-56
277. The tachometer often referred as TACH, is calibrated in hundreds with gradation at every --- RPM interval
a. 100 RPM interval 12A 10-24
278. The red indicates the maximum RPM permissible during takeoff, any rpm beyond this valve is an
a. Over speed condition 12A 10-24
279. In which indicator is also an indication of proper operation of engine oil cooler
a. Oil inlet temperature 12A 10-58
280. In which lever is usual provided on engine equipped with thrust reversers
a. Fuel shutoff lever 12A 10-58
281. Fuel flow in turbine engine is measured in
a. Ibs/hr instead of gallons 12A 10-58
282. Tachometer is usually caliberated in
a. Percent RPM 12a 10-56
283. What are the agents used for decreasing the engine parts
a. Emulsion type cleanes or chlorinated solvents
284. What is the purpose of an oil pressure indicator
a. It shows the engine oil pump discharge pressure 12A 10-58
285. In an axial compressor engine, what is the main purpose of a tachometer
a. It monitor the rpm settings on engine start and indicate over speed conditions
286. For checking the resistance of a thermocouple which unit can be used
a. JETCAL analyzer / trimmer system kroes 531-532
287. In gas turbine engine where the cobalt chloride silica gel is used
a. Humidity indicator envelops 12A 8-25
288. In the case of engine mounts, which bolts support the weight of the engine when it is in ground
a. Upper bolts 12A 8-22
289. A small rounded depression in a surface usually caused by the part being struck with a rounded object is called
a. Dent 12A 10-3
290. A series of bunt depressions in a surface is called
a. Peening 12A 10-4
291. is the step- by step procedure used to determing the cause of a given fault and then select the best and quickest solution
a. Trouble shooting kroes 229
292. Most turbine engine mounts are made of
a. Stainless steel 12A 8-24
293. Tachometer is usually calibrated in
a. Percent RPM 12A 10-56
294. For checking the resistance of a thermocouple which unit canbe used
a. Jet cal analyser kroes 531-53
b. Ibs/ hr instead of allons 12A 10-58
295. In gas turbine engine where the cobalt silica gel is sed
a. Humidity indicator envelops 12A 8-25
296. A series of blunt depressions in a surface is called
a. Peening 12A 10-4
297. What are the agents used for decreasing th engine parts
a. Emulsion type cleanse or chlorinated solvent 12A 10-49
298. In which lever is usually provided on engine equipped with thrust reversers
a. Fuel shut off lever 132A 10-58
299. Oil analysis programs identity and measures these particles in – by weight
a. Parts per million 12A 6-22
300. Tacho meter is usually calibrated in
a. – RPM 12A pagr10
301. The purpose of an oil – indicator is to indicate
a. Engine oil pump discharge --- 12A 11
302. Most turbine engine mounts are made of
a. Stainless steel 12A 18
303. In gas turbine engine where the cobalt chloride silica gel is used
a. humidity indicator envelops 12A 8-25
304. What is the purpose of an oil pressure indicator
a. It shows the engine oil pump discharge pressure 12A 10-58
305. What are the agent used degreasing the engine parts
a. Emulsion type clean or --- solvent 12A 10-49
306. The exhaust temperature in proportional to
a. Turbine --- temperature 12A 10-55
307. --- is the step by step procedure used to determine the cause of a given fault and then select the best and quickest solution
a. Trouble shooting kroes 229
308. Large gas turbine engines are generally equipped with ----- starts which receive their air supply from a ground service unit aircraft another
engine or an auxiliary power unit is installed in the aircraft
a. Air turbine kroes 499
309. Turbo prop are usually fitted with a ---- that measures torque applied to a shaft turned by a gas generator and power turbines of the
turbine engine
a. Torque meter 12A 10-56
310. The mounts supports the power plants and isolate the airplane structure --- adverse engine vibrations
a. Vibration isolator engine 12A 8-24
311. Generally --- is used to transfer the oil pressure in to an electrical signal to be read by the flight deck instrument
a. Transducer 12A 10-56
312. Most turbine engine mounts are made of ---
a. Stainless steel 12A 8-24
313. For checking the resistance of a thermo couple which unit can be used
a. JETCAL analyzer kroes 531-532
314. Tachometer is usually calibrated in
a. Percent RPM 12A 10-58
315. The purpose of an oil pressure indicator is to indicate
a. Engine oil pump discharge pressure 12A 10-58
316. The engine must be retrimmed ---
a. A fuel control unit is replaced 12A 10-55
317. The exhaust temperature is -----
a. The turbine inlet temperature 12A 10-55
318. Tacho meter is usually calibrated in
a. Present RPM (12A 1056
319. The exhaust temperature is --- to
a. The turbine inlet temperature 12A 10-55
320. The EGT indicates in flight decade shows
a. The average temperature measured by individual thermo couples 12A 1056
321. The gads turbine engine where the cobalt chloride silica gel is used
a. Humidity indicator 12A 8-25
322. A change in color --- using notices by different appearance from the surrounding area
a. Stain 12A 10-3
323. For checking the resistance of a thermo couple --- which unit can be used
a. JETCAL analysis / trimmer system kroes 531-532
324. What are the agents used for --- the engine parts
a. Emulsion type cleanse or chlorinated solvent 12A 10-49
325. Fuel flow in turbine engine is measured in
a. Ibs/ hr instead of gallons 12A 10-58
326. Explain the fuel system bleeding 12A 10-49
327. The EGT indication in flight deck show
a. The average temperature by individual thermo couple 12A 10-56
328. The engine must be retrimmed by after
a. A fuel control unit is replaced 12A 10-56
329. For checking the resistance of a thermo couple harness which unit can be used
a. JETCAL analyzer trimming system kroes 523-532
330. What are the agents used for degreasing engine parts
a. Solvent 12A 10-49
331. A change in color locally
a. using noticeably --- appearance 12A 10-3
332. all parts showed be given an inspection either or they are removed on the engine or immediate.ly at the --- of siassembly
a. primary inspection kroes 241
333. an oil sample to be analyzed and searched for the presence of minute
a. metallic elements the process is called spectrometriric are analysis program 12A 6-21
334. Fuel flow in turbine engine is measured in
a. Ibs/ hr instead of gallons 12A 10-58
335. The engine is installed facing ---- with the propellers shaft approximately how many degree above horizontal
a. 39 degree above horizontal 12A 8-25
336. In which lever is usually provided on engines equipped with thrust reversers
a. Fuel shut of lever 12A 10-580
337. A small rounded depression in a surface usually caused by the part being struck with a rounded object is called
a. Dent 12A 10-3
338. Why water injection system required
a. To increase thrust for take off 12A 10-55
339. The step by step procedure used to determine the cause of a given fault and to select the best and quickest solution is called
a. Trouble shooting kroes 229
340. What is mean by trimming of a gas turbine engine
a. Process of adjusting the fuel control unit
341. What is the purpose of jetcal
a. Calibrate and monitor engine health kroes 531
342. What are the components co- coordinating a jetcal analyser
a. Instrument case, Accessory case kroes 531
343. Objective of ahot section inspection
a. Maintain turbine blade3 tip clearance kroes 500
344. Oil pressure is taken at the
a. Pump outlet kroes 72
345. Oil analysis programme identify and measures those particles in parts per million by weight 12A 6-21
346. In which lever is usually provided on engine equipped with thrust reversers
a. Fuel shut off lever 12A 10-58
347. A small rounded depression in a surface usually caused by the part is being struck with rounded object is called
a. Dent 12A 10
348. Tachometer is usually calibrated in
a. Percent RPM 12A 10-56
349. The vibration kolator engine mount supports the power plant and isolate the airplane structure from adverse engine
a. Vibrations 12A 8-24
350. For checking the resistance of a thermocouple which unit can be used
a. Jetcal analyser / trimmer system
351. In axial compressor engine what is main purpose of a tachometer
a. Monitor the RPM settings on engine start and lubricate over speed conditions 12A 10-56
352. In which lever is usually provided on engine equipped with thrust reverser
a. Fuel shutoff lever 12A 10-58
353. The EGT indicator in the flight deck shows the Average temperature measured by
a. Thermocouple
354. Red line indicates the maximum RPM permissible during take off any RPM beyond this valve is
a. Over speed condition 12A 10-24
355. Fuel flow indicator shows
a. Pounds / hrs
356. Oil pressure is taken at
a. Pump outlet kroes 72
357. Turbo props are usually fitted with a --- that measures torque applied to a shaft turned by a gas generator and power turbine of thwe
turbine engine
a. Torque meter 12 A 10-15
358. Generally --- is used to transfer the oil pressure in to an electrical signal to be read by the flight deck instrument
a. Transducer 12A 10-56
359. Most turbine engine mounts are made of –
a. Stainless steel 12A 18-24
360. The purpose of an oil pressure indicator is to indicate
a. Engine oil pump discharge pressure
361. Breaking away of metal that is usually caused by excessive stress or concentration or careless handling is known
a. Chipping 12A 10-3
362. ----- one or more indentations on bearing races usually caused by high static loads or application of force during installation or removed
a. Brinelling 12A 10-3
363. All bearing surface should be examined for
a. Scores, galling and wear 12A 10-4
364. Checking the --- is one of the procedures in the maintenance of turbine section of a turbine engine
a. Clearance 12A 10-55
365. --- on tail cone are the good indication of a malfunctioning fuel nozzle or combustion chamber
a. Hotspots 12A 10-55
366. --- is an indication of the thrust being developed by a turbofan engine and is used to set power for take of on many types of aircraft
a. Engine pressure ratio 12A 56
367. --- is an engine operating limit and is used to monitor the mechanical integrity of the turbines as well as to check engine operating
conditions
a. Temperature 12A 56
368. The EGT indications in flight deck shows
a. The average temperature measured by individual thermocouple
369. The engine must be retrimmed after
a. A fuel control unit replaced
370. For checking the resistance of a thermo couple harnell which unit can be used
a. JETCAL analyzer trimming system kroes 531-532
371. What are the agents used for greasing the engine parts
a. Emulsion tytpe cleanser or chloride solvent 12A 10-49
372. A change in color locally using noticeably --- appearance from surrounding area
a. Stain 12A 10-3
373. Tachometer is usually calibrated in
a. Percent RPM 12A 10-5
374. Fuel flow instruments indicate
a. Fuel flow in pounds per hour 16/ hr 12A 10-58
375. The detection of fault indications and the isolated of the fault or faults causing the indications
a. Trouble shooting kroes 532
376. --- of blunt suppressions in a surface
a. Peening 12A 10-4
377. A condition caused by a rubbing action between two parts under light pressure that results in wear
a. Chaffing 12A 10-3
378. Oil analysis programs identity and measures these particles in—by weight
a. Parts per millions 12A 6-21
379. The EGT indication in the flight deck shows the average temperature measured by
a. Thermo couples 12A 10-56
380. In which lever is usually provided on engine equipment with thrust reverser
a. Fuel shutoff lever 12A 10-58
381. The red line indicates the maximum rpm permissible during take off any rpm beyond this valve is an
a. Over speed condition 12A 10-24
382. Tachometer is calibrated in
a. Percent Rpm 12A 10-56
383. What is the step by step procedure used to determine the cause of a given fault and then select and best and equivalent solution
a. Trouble shooting kroes 229
384. The engine mounts are made from what
a. Stainless steel 12A 8-24
385. Which unit is used for checking the resistance of a thermocouple
a. JETCAL analyzer kroes 531-532
386. A series of blunt depression in a surface is called what
a. Peening 12A 10-14
387. What is used to transfer the oil pressure ion to an electrical signal to be read by the flight deck instrument
a. Transducer 12A 10-56
388. The purpose of an oil pressure indicator is to indicate engine oil pump discharge pressure 12A 10-58
389. Turbo prop are usually fitted with a torque meter that measures torque applied to a shaft truned by a gas generator and power turbines
of the turbine engine 12A 10-56
390. A small rounded depressions in a surface usually caused by the part being struck with a rounded object is called
a. Dent
391. What are the preliminary steps applicable for the turbo fan power plant QECA removal (12A 8-18)
Fuel system ref : trigger 579
Fuel from the aircraft fuel system enters the engine at the engine main – fuel pump inlet. Pressure fuel from this two stage pump flows through the fuel- oil heat
exchanger through the fuel filter, and into the main engine control. Metered fuel from the fuel control flows through the pressurizing valve, through the
customer- furnished flow meter, through the fuel manifold, and into the 30 fuel nozzles. A fuel manifold, over board drain eliminator ( educator and valve
assembly), is supplied as optional equipment. The educator and valve assembly pumps the fuel that drains from the fuel manifold in to the aircraft drain can back
in to the aircraft fuel system via the fuel pump educator during engine shutdown. The engine fuel control also schedules pressure fuel to actuate the variable
stator vane system and the CF6-50 variable by pass doors. By pass fuel from the control is returned to the fuel pump interstage.

The fuel system is characterized by the clustering of the primary system components around the fuel pump and by mounting this cluster on the accessory gear
box. This feature has several advantages.
Locates the fuel system components in a low- temperature environment of minimum fire hazard
Eliminates the complex bracketry and plumbing required for individual components by providing internal flange mated parts for each component
Enables easy maintenance because of easy access
The combined effects of this feature serve to enhance the overall reliability of the fuel system.

Вам также может понравиться