Академический Документы
Профессиональный Документы
Культура Документы
Formerly Masterseal S
Sprayable, chlorinated rubber based, curing and sealing compound
DESCRIPTION The surface may be damp but with no free water on it. In
the case of formed concrete, apply immediately after
MASTERKURE 300CR is a clear, ready to use, striking the formwork.
chlorinated rubber based curing membrane and sealing Delaying the application until the next day will allow
compound. substantial loss of moisture reducing the effectiveness of
the curing membrane.
RECOMMENDED FOR For best results, apply an even coat by airless spray at a
pressure of 110 - 160 kg/cm2 using a nozzle with tip size
MASTERKURE 300CR is recommended for curing 0.43 - 0.48 mm. It can also be applied with a wide short
freshly placed concrete floors and vertical surfaces nap roller, or brush to the recommended thickness.
where after curing, the concrete surface has also to be Avoid too thick an application to prevent blisters and
protected from staining caused by spillage of mild debonding caused by solvent entrapment. With all
chemicals, mineral oils and grease. Areas of application methods, take adequate care to prevent marring of
include curing of, concrete surface.
• workshop floors, beam and columns, For curing only, a single coat is recommended. For
• cementitious toppings and surface hardening curing and sealing, apply one further coat after the first
finishes such as Mastertop 100, Mastertop 200, coat has dried.
Mastertop 210 and Mastertop 103.
• cementitious grouts and mortars. EQUIPMENT
FEATURES AND BENEFITS Airless spray machine, short nap mohair roller and
brush.
Effective moisture Facilitates complete hydration of
retention in cement resulting in greater CLEANING
concrete strength and superior wear
Clean tools and equipment using a hydrocarbon based
resistance.
solvent such as xylene.
Seals surface Protects concrete from staining
and ingress of liquids. Also ESTIMATING DATA
minimises dusting.
Bonds to non No need to remove membrane Consumption depends on the surface profile, porosity
cement based tile before laying ceramic or vinyl and method of application. When applied with a roller
adhesives tiles. onto a smooth, dense surface, MASTERKURE 300CR
2
gives a typical coverage of 5 m /L per coat.
2
PROPERTIES Therefore, material requirement will be 0.20 L/m per
coat on a dense smooth surface.
Supply form : Viscous liquid
Colour : Clear PACKAGING
MASTERKURE 300CR will yellow with prolonged MASTERKURE 300C is available in 20 L pails and 205
exposure to UV light but this will not affect its curing L drums.
efficiency.
STORAGE
APPLICATION
Store away from sources of heat and ignition in a
Use MASTERKURE 300CR as supplied without dilution. shaded, dry, well enclosed area at moderate
Stir the contents of the container using a slow speed temperatures.
(600 rpm) electric drill fitted with a wing type paddle,
before applying. SHELF LIFE
It should be applied after the final finishing operation as
soon as the concrete or mortar surface has hardened MASTERKURE 300CR can be stored in tightly sealed
sufficiently to prevent marring. original containers for 12 months when stored as
recommended.
I Mk300CR/3/0602
The technical information and application advice given in this BASF Construction Chemicals
publication are based on the present state of our best scientific and practical knowledge. As the
STATEMENT OF information herein is of a general nature, no assumption can be made as to a product's suitability for a
RESPONSIBILITY particular use or application and no warranty as to its accuracy, reliability or completeness either
expressed or implied is given other than those required by law. The user is responsible for checking the
suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by
BASF Construction Chemicals either orally or in writing may be followed, modified or rejected by the
NOTE owner, engineer or contractor since they, and not BASF Construction Chemicals, are responsible for
carrying out procedures appropriate to a specific application.