Академический Документы
Профессиональный Документы
Культура Документы
Centrifugal Separation
Content
2.1 Introduction
2.1.1 Use centrifugal field other than separation
2.2.Pressure in the centrifugal field
2.3 Comparison of Separation of immiscible liquids of different densities in gravity settling and in
centrifuge
2.4 Filtration in centrifuge
2.5 Motion of a particle suspended medium
2.6 Sedimentation in centrifugal field
2.7 Design of sedimentation Centrifuge
2.8 Equipments
2.9 Assignment
2.1 Introduction
(see chapter-9 of ref 1).
In many a cases, the external body force, gravity is inadequate to separate very fine particles, but
the centrifugal force field can do the separation due to the possibility of its large magnitude. The
centrifugal force field can be used for separation of suspended particles.
The centrifugal field can be created by following two ways: (a)by using a centrifuge, and (b)by
passing fluid tangentially into a cylindrical or conical vessel. In a centrifuge, a fluid is introduced
into a bowl and and is rapidly accelerated. Because the frictional drag within the fluid ensures
that there is very little rotational slip or relative motion between fluid layers within the bowl, all
the fluid tends to rotate at a constant angular velocity, .
The rotational field created in the above cases are distintly different in terms of the
angular motion of the fluid elements. In the case of centrifuge, the fluid rotates as a solid body
(see figure-1). This is called rotational flow. The tangential velocity component, v is given by
v=r. But for the later case, the fluid element rotates such a way that it suffers no net rotation
from one instant to the next, with respect to the given frame of reference (see figure-2). The
irrotational flow can be utilized in cyclone separator, which will be discussed later.
v r
v =c/r
(b) For separating immiscible liquids of different densities, which may be in the form of
dispersions or even emulsions in the feed stream. This is the equivalent of a gravitational
decantation process.
(c) For filtration of a suspension. In this case centrifugal force replaces the force of gravity or the
force attributable to an applied pressure difference across the filter. (d) For the drying of solids
and, in particular, crystals. Liquid may be adhering to the surface of solid particles and may be
trapped between groups of particles. Drainage may be slow in the gravitational field, especially if
the liquid has a high viscosity. Furthermore, liquid is held in place by surface tension forces
which must be exceeded before liquid can be freed. This is particularly important with fine
particles. Thus, processes which are not possible in the gravitational field can be carried out in
the centrifuge.
(e) For breaking down of emulsions and colloidal suspensions. A colloid or emulsion may be
quite stable in the gravitational field where the dispersive forces, such as those due to Brownian
motion, are large compared with the gravitational forces acting on the fine particles or droplets.
In a centrifugal field which may be several thousand times more powerful, however, the
dispersive forces are no longer sufficient to maintain the particles in suspension and separation is
effected.
(f) For the separation of gases. In the nuclear industry isotopes are separated in the gas
centrifuge in which the accelerating forces are sufficiently great to overcome the dispersive
effects of molecular motion. Because of the very small difference in density between isotopes
and between compounds of different isotopes, fields of very high intensity are needed.
(g) For mass transfer processes. Because far greater efficiencies and higher throughputs can be
obtained before flooding occurs, centrifugal packed bed contactors are finding favour and are
replacing ordinary packed columns in situations where compactness is important, or where it is
desirable to reduce the holdup of materials undergoing processing because of their hazardous
properties. An important application is the use of inert gases in the desorption of oxygen from
sea water in order to reduce its corrosiveness; in North Sea oil rigs the sea water is used as a
coolant in heat exchangers. In addition, centrifugal contactors for liquid–liquid extraction
processes now have important applications.
2.2. Pressure in the centrifuge
dp
2 r
dr
p R pr 0
1 2 2
2
R r02
The pressure depends on rotational speed and radius of the container.
2.3 Comparison of Separation of immiscible liquids of different densities in gravity settling and in
centrifuge
See lecture slides
2.8 Equipments
See Coulson and Richardson vol-2 Chapter 9.
5. In the above problem, we would like to scale up the centrifuge. We have to design a
centrifuge such that it can handle 1.5 times Vf in Question (2). r1 and r2 remains same, find
the length of the centrifuge. Both the centrifuges have same rotational speed?
6. A centrifuge is fitted with a conical disc stack (see figure below) with an included angle of 2,
and there are n flow passages between the discs. A suspension enters at radius r1 and leaves at
radius r2. Obtain an expression for the separating power Σ of the centrifuge. It may be assumed
that the resistance force acting on the particles is given by Stokes’ law.
References:
2. Foust, A.S. et al., Principles of Unit Operations (2nd Edition), John Wiley, 1980, pp.
620-629.
3. McCabe, W.L., J.C. Smith, and P. Harriott, Unit Operations of Chemical
Engineering (5th Edition), McGraw-Hill, 1993, pp. 31-32, 37-39, 1060-1072.
4. Probstein, R.F., Physicochemical Hydrodynamics: An Introduction (2nd
Edition), John Wiley, 1994, pp. 142-147.