Академический Документы
Профессиональный Документы
Культура Документы
product guide
Sheet and Coil
product guide
Index
Limited Edition. This publication has been compiled for the ASI Australian Steel Convention 2010 as a preview of
content to be featured in the BlueScope Steel sheet and coil website that will be launched in November 2010.
BlueScope Steel is proud of its comprehensive range of All products in the sheet and coil range comply with the coating in the total coated thickness measurement of their
sheet and coil products - hot rolled coil, cold rolled coil, dimensional tolerances specified in AS/NZS 1365:1996. metallic coated products, which may mean that the product
metallic coated coil and pre-painted coil. Additionally, our hot rolled coil products are manufactured to will not meet design requirements or appropriate Australian
Australian Standard AS/NZS 1594:2002 and most cold rolled Standards.
This sheet and coil product guide provides you and your coil products in the sheet and coil range are manufactured to
customers with the information required to choose the AS/NZS 1595:1998. The subsequently applied metallic coating
“best fit” product from our sheet and coil range for your end thickness conforms to AS 1397: 2001 while paint coatings
Quality Designed
use application. conform to AS/NZS 2728:2007 in the appropriate Type. BlueScope Steel’s metallic and pre-painted sheet and coil
products are tested in Australian conditions for many years in
BlueScope Steel’s sheet and coil products are considered Our test certificates provide pertinent information regarding evaluation programs, before and after commercialisation. No
the benchmark by Australia’s diverse manufacturing the manufacture and testing of all sheet and coil products. other steel company designs and tests sheet and coil products
industry for quality, delivery and supply flexibility, product This recorded information, in conjunction with unique for Australian conditions.
range and technical support. And being made in Australia, product identity for each mill coil, provides complete product
they’re the only sheet and coil products designed for and traceability to support customers’ quality systems. Our in-house research team monitors more than 19,000 steel
tested to perform in Australian conditions. test panels at seven outdoor test sites around Australia,
BlueScope Steel also holds ISO Quality Management System collecting data regarding corrosion and weathering
Accreditation (ISO 9001), a third party accreditation that further performance. BlueScope Steel has over 30 years of exposure
Quality Assured
assures the quality of our products. data. This forms the basis for continual improvements to the
BlueScope Steel stands behind its products by certifying performance of the coatings applied to our sheet and coil
their compliance to independently established Australian BlueScope Steel’s metallic coated sheet and coil products products.
Standards. These standards cover such matters as the are rolled and sold according to their base metal thickness
steel’s chemical composition and mechanical properties, (BMT), as specified in AS/NZS 1365: 1996. The metallic
associated testing, inspection, certification procedures, coating thickness is additional to the base metal thickness.
dimensional tolerances and coatings application. Competitors’ products may include the base metal and metallic
BlueScope Steel’s sheet and coil product range comprises - hot rolled coil, cold rolled coil, metallic coated
coil and pre-painted coil. The table below features the various grade designations and brands associated
with the product range.
HA250 steel CA180S-G steel GALVASPAN® steel COLORBOND® Insulated Panel steel
HA1010 steel CM350-G steel XHW Exterior Hot Water Pre-Painted steel
XK15B28 steel CU200T-G steel XMA Exterior Manufactured Articles Pre-Painted steel
HA70T-P steel CV2S1 steel GMA General Manufactured Articles Pre-Painted steel
BlueScope Steel’s sheet and coil products are assigned ‘codes’ or designations that describe the product
type, performance and other related product characteristics. These designations have been adopted
from the Australian Standards.
Example: H A 70 T P
HA250 steel Structural steel with a minimum BlueScope Steel Bending................................ 3 Structural AS/NZS 1.6 to 12.7 Up to 1800 As rolled.
yield strength of 250 MPa with good hot rolled Drawing ................................2* sections, light 1594:2002
ductility. (structural grade) Pressing ................................2* poles, guard rails AS/NZS Optional, pickled and oiled.
Roll forming ......................... 4 and gas cylinders 1365:1996 (conditions may be
Welding................................ 5 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
HA300 steel Structural steel with a minimum BlueScope Steel Bending................................ 3 Structural AS/NZS 1.6 to 12.7 Up to 1800 As rolled.
yield strength of 300 MPa with good hot rolled Drawing ................................2* sections, light 1594:2002
ductility. (structural grade) Pressing ................................2* poles, guard rails AS/NZS Optional, pickled and oiled.
Roll forming ......................... 3 and automotive 1365:1996 (conditions may be
Welding................................ 5 components subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
HA350 steel Structural steel with a minimum BlueScope Steel Bending................................ 3 Structural AS/NZS 1.6 to 6 Up to 1700 As rolled.
yield strength of 350 MPa and good hot rolled Drawing ...............................2* sections, racking, 1594:2002
ductility. (structural grade) Pressing ...............................2* truck chassis and AS/NZS Optional, pickled and oiled.
Roll forming ......................... 3 gas cylinders 1365:1996 (conditions may be
Welding................................ 5 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
XTRAFORM® Hot rolled steel suitable for severe BlueScope Steel Bending................................ 5 Automotive AS/NZS 1.6 to 6 Up to 1530 As rolled.
300 steel forming and bending with a hot rolled Drawing ................................4* components 1594:2002
guaranteed minimum yield strength (extra formable Pressing ................................4* AS/NZS Optional, pickled and oiled.
of 300 MPa. grade) Roll forming ......................... 5 1365:1996 (conditions may be
Welding.................................4 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
XTRAFORM® Extra formable, structural steel BlueScope Steel Bending................................ 5 Automotive AS/NZS 1.6 to 6 Up to 1530 As rolled.
400 steel suitable for severe forming and hot rolled Drawing ................................3* components and 1594:2002
bending with a guaranteed minimum (extra formable Pressing ................................3* gas cylinders AS/NZS Optional, pickled and oiled.
yield strength of 380 MPa. grade) Roll forming ......................... 5 1365:1996 (conditions may be
Welding................................ 4 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
XTRAFORM® Hot rolled extra formable, structural BlueScope Steel Bending................................ 5 Automotive AS/NZS 2.5 to 6 Up to 1530 As rolled.
500 steel steel suitable for severe forming and hot rolled Drawing ................................3* components 1594:2002
bending with a guaranteed minimum (extra formable Pressing ................................3* AS/NZS Optional, pickled and oiled.
yield strength of 480 MPa. grade) Roll forming ......................... 5 1365:1996 (conditions may be
Welding................................ 4 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................NR
BRIGHTFORM® steel Formable, commercial forming steel BlueScope Steel Bending................................ 4 Tubing, shelving, AS/NZS 1.6 to 3 Up to 1510 Pickled and oiled.
suitable for simple forming and hot rolled Drawing ................................3* simple pressings, 1594:2002
bending operations. (formable grade) Pressing ................................3* hidden appliance AS/NZS
Roll forming ......................... 4 panels and 1365:1996
Welding................................ 5 distributor stock
Painting (pre-treatment)...... 5
Galvanising .......................... 5
HA3 steel Formable steel suitable when pickled BlueScope Steel Bending................................ 5 Agricultural AS/NZS 1.5 to 12.7 Up to 1800 As rolled.
for medium drawing and heavy hot rolled Drawing ................................4* machinery, 1594:2002
pressing operations. Available skin (formable grade) Pressing ................................4* automotive AS/NZS Optional, pickled and oiled.
passed for minimum coilbreak and Roll forming ......................... 5 components, 1365:1996 (conditions may be
improved flatness. Welding................................ 5 sealed unit subject to dimensional
Painting (pre-treatment)...... 5 housings, mower restrictions)
Galvanising .......................... 5 parts, brackets
and furniture
HA4N–P steel Formable, pickled, extra deep drawing BlueScope Steel Bending................................ 5 Automotive AS/NZS 2 to 6 Up to 1500 Pickled and oiled.
steel guaranteed non ageing, suitable hot rolled Drawing ................................5* components, 1594:2002 (but subject to dimensional
for severe drawing and pressing. (formable grade) Pressing ................................5* mower parts AS/NZS restrictions)
Roll forming ......................... 5 1365:1996
Welding................................ 5
Painting (pre-treatment)...... 5
Galvanising .......................... 5
HA1010 steel Carbon steel with a guaranteed BlueScope Steel Bending................................ 3 Gas cylinders and AS/NZS 1.6 to 12.7 Up to 1800 As rolled.
chemical composition, good ductility hot rolled Drawing ................................2* hot water system 1594:2002
and good weldability. (analysis grade) Pressing ................................2* cylinders AS/NZS Optional, pickled and oiled.
Roll forming ......................... 3 1365:1996 (conditions may be
Welding................................ 5 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
XK15B28 steel Carbon steel with a guaranteed BlueScope Steel Bending................................ 3 Ground engaging AS/NZS 2 to 8 Up to 900 As rolled.
chemical composition. Suitable for hot rolled Drawing ................................2* tools, plough discs 1594:2002
applications requiring good wear (analysis grade) Pressing ................................2* and wear abrasion AS/NZS Optional, pickled and oiled.
resistance after heat treatment. Roll forming ......................... 3 applications 1365:1996 (conditions may be
Welding................................ 5 subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
Galvanising .......................... 5
HA70T-P steel Hot rolled, pickled and temper rolled BlueScope Steel Bending ............................... 3 Racking, AS/NZS 1.4 to 3 Up to 1220 Not oiled.
steel with guaranteed minimum hot rolled Drawing ........................... NR* shelving, 1365:1996
hardness of 70 HRB, suitable for (hardness grade) Pressing ...............................1 automotive Optional, oiled.
limited bending. Roll forming ........................ 3 components (conditions may be
Welding ............................... 5 subject to dimensional
Painting (pre-treatment) ...... 5 restrictions)
Galvanising ......................NR
CA180S-G steel Supplier negotiated cold rolled, BlueScope Steel Bending................................ 5 Non-exposed AS/NZS 0.7 to 1 Up to 1530 Surface finish matt oiled.
skin passed, deep drawing steel. cold rolled Drawing ............................... 4 severely drawn 1365:1996 Optional: not oiled
Guaranteed non ageing and free (formable grade) Pressing ............................... 4 parts for trimmed edge; mill edge.
from stretcher strain, with a general Roll forming ......................... 5 automotive and (Optional conditions may
purpose finish. Welding................................ 5 appliance end be subject to dimensional
Painting (pre-treatment)...... 5 uses restrictions)
CA220S-G steel Cold rolled, skin passed, deep BlueScope Steel Bending................................ 5 Non-exposed AS/NZS 0.6 to 2 Up to 1530 Surface finish matt oiled.
drawing steel. Guaranteed minimum cold rolled Drawing ............................... 4 severely drawn 1595:1998 Optional: not oiled
yield strength of 210 MPa, non ageing (formable grade) Pressing ............................... 5 parts for AS/NZS trimmed edge; mill edge.
and free from stretcher strain, with a Roll forming ......................... 5 automotive and 1365:1996 (Optional conditions may
general purpose surface. Welding................................ 5 appliance end be subject to dimensional
Painting (pre-treatment)...... 5 uses restrictions)
CA260S-G steel Cold rolled, skin passed, deep BlueScope Steel Bending................................ 5 Non-exposed AS/NZS 0.6 to 2.5 Up to 1530 Surface finish matt oiled.
drawing steel. Guaranteed minimum cold rolled Drawing ............................... 4 automotive panels 1595:1998 Optional: not oiled
yield strength of 250 MPa, non ageing (formable grade) Pressing ............................... 5 AS/NZS trimmed edge; mill edge.
and free from stretcher strain, with a Roll forming ......................... 5 1365:1996 (Optional conditions may
general purpose surface. Welding................................ 5 be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
CA2S-E steel Skin passed commercial drawing BlueScope Steel Bending................................ 5 Office furniture AS/NZS 0.5 to 3.2 Up to 1530 Surface finish matt oiled.
steel for moderate forming and cold rolled Drawing ............................... 3 and shelving 1595:1998 Optional: lustre; not oiled
pressing with a surface suitable for (formable grade) Pressing ............................... 3 AS/NZS trimmed edge; mill edge.
exposed applications. Roll forming ......................... 5 1365:1996 (Optional conditions may
Welding................................ 5 be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
NR: not recommended
CA4A-G steel Cold rolled, non skin passed extra BlueScope Steel Bending................................ 5 Non-exposed AS/NZS 0.6 to 2.2 Up to 1530 Surface finish matt oiled.
deep drawing steel suitable for cold rolled Drawing ............................... 5 severe pressings 1595:1998 Optional: not oiled
severely drawn non-exposed (formable grade) Pressing ............................... 5 such as AS/NZS trimmed edge; mill edge.
applications where stretcher strain Roll forming ......................... 5 automotive oil 1365:1996 (Optional conditions may
marking is not objectionable. Welding................................ 5 pans be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
CA5SN-E steel Skin passed critical drawing BlueScope Steel Bending............................... 5 Exposed severely AS/NZS 0.6 to 3 Up to 1530 Surface finish matt oiled.
steel suitable for severely drawn cold rolled Drawing .............................. 5 drawn parts for 1595:1998 Optional: not oiled
components in exposed applications (formable grade) Pressing .............................. 5 automotive and AS/NZS trimmed edge; mill edge.
with a minimum of surface rework. Roll forming ........................ 5 appliance end 1365:1996 (Optional conditions may
Guaranteed non ageing and free from Welding............................... 5 uses be subject to dimensional
stretcher strain. Painting (pre-treatment)..... 5 restrictions)
CA85T-G steel Guaranteed minimum hardness of 85 BlueScope Steel Bending................................1 Seals, washers, AS/NZS 0.4 to 3.2 Up to 1530 Surface finish as cold-
HRB suitable for flat blanking. cold rolled Drawing ...........................NR brackets and 1595:1998 rolled oiled.
(hardness grade) Pressing ...........................NR hinges AS/NZS Optional: not oiled
Roll forming .........................1 1365:1996 trimmed edge; mill edge.
Welding ...............................5† (Optional conditions may
Painting (pre-treatment)..... 5 be subject to dimensional
restrictions)
DRUMSTOCK® steel Cold rolled skin passed steel BlueScope Steel Bending................................ 5 Drum and pail AS/NZS 0.6 to 1.4 Up to 1220 Surface finish matt not
produced specifically for the container cold rolled Drawing ............................... 2 bodies and ends 1365:1996 oiled trimmed edge.
market. (hardness grade) Pressing ............................... 2 Optional: mill edge.
Roll forming ......................... 5 (Optional conditions may
NR: not recommended Welding................................ 5 be subject to dimensional
†
design must allow for some strength reduction near welds Painting (pre-treatment)...... 5 restrictions)
CM350-G steel Cold rolled, high strength, low alloy BlueScope Steel Bending................................ 5 Guard rails and AS/NZS 0.7 to 2 Up to 1530 Surface finish matt
steel combining high yield strength. cold rolled Drawing ............................... 3 structural sections 1365:1996 oiled. Optional: not oiled
Guaranteed 350 MPa minimum yield (structural grade) Pressing ............................... 3 trimmed edge; mill edge.
strength with good formability. Roll forming ......................... 5 (Optional conditions may
Welding................................ 5 be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
CU200T-G steel Cold rolled and temper-rolled steel BlueScope Steel Bending................................ 5 Tubing and general AS/NZS 0.5 to 3.2 Up to 1530 Surface finish matt oiled.
with a guaranteed minimum yield cold rolled Drawing ............................... 2 pressing 1365:1996 Optional: lustre; not oiled
strength of 200 MPa suitable for (structural grade) Pressing ............................... 2 trimmed edge; mill edge.
general fabrication and welding. Roll forming ......................... 5 (Optional conditions may
Welding................................ 5 be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
CV2S1 steel Cold rolled and skin passed BlueScope Steel Bending................................ 5 Stove liners and AS/NZS 0.5 to 3.2 Up to 1530 Surface finish matt oiled.
commercial drawing steel. cold rolled Drawing ............................... 3 heaters 1365:1996 Optional: not oiled
Guaranteed for general purpose (vitreous Pressing ............................... 3 trimmed edge; mill edge.
vitreous enamelling with appropriate enamelling Roll forming ......................... 5 (Optional conditions may
enamelling practices. Unsuitable for grade) Welding................................ 5 be subject to dimensional
direct on cover coat, or two coat, one Painting (pre-treatment)...... 5 restrictions)
fire white enamels.
GALVABOND® GALVABOND® 3N steel is a hot- BlueScope Steel Bending................................ 5 Automotive panels AS/NZS 0.5 to )1.6 Up to 1525 Surface finish spangled.
G3N steel dipped zinc coated deep drawing metallic coated Drawing ............................... 4 and components, 1365:1996 Optional: minimal spangle
G3NS steel steel with a spangled surface, (formable grade) Pressing ............................... 3 drawn appliance AS 1397:2001 passivated; unpassivated/
guaranteed non ageing and free from Roll forming ......................... 5 panels and oiled.
stretcher strain. Lock forming ........................ 5 components (Optional conditions may
Welding................................ 5 be subject to dimensional
Painting (pre-treatment)...... 5 restrictions)
GALVASPAN® G450 steel is a hot-dipped zinc coated BlueScope Steel Bending................................ 3 Roll formed AS/NZS *1.5 to )3.2 Up to 1350 Surface finish spangled
G450 steel structural steel with a spangled metallic coated Drawing ............................NR sections for 1365:1996 passivated
surface and guaranteed minimum (structural grade) Pressing ............................NR structural AS 1397:2001
yield strength of 450 MPa. Suitable Roll forming ......................... 3 applications
for roll forming to a minimum internal Lock forming ........................ 5
diameter of 4t. Welding................................ 5
Painting (pre-treatment)...... 5
GALVASPAN® G500 steel is a hot-dipped zinc coated BlueScope Steel Bending................................ 2 Roll formed AS/NZS >1 to <1.5 Up to 1350 Surface finish spangled
G500 steel structural steel with a spangled metallic coated Drawing ............................NR sections for 1365:1996 passivated
surface and guaranteed minimum (structural grade) Pressing ............................NR structural AS 1397:2001
yield strength of 500 MPa. Suitable Roll forming ......................... 3 applications
for roll forming to a minimum internal Lock forming ........................ 5
diameter of 4t. Welding................................ 5
Painting (pre-treatment)...... 5
NR: not recommended
ZINCALUME® G2N is a hot-dipped zinc/aluminium BlueScope Steel Bending................................ 5 Garage door AS/NZS 0.6 to ) 0.75 Up to 1100 Surface finish spangled
G2N steel alloy-coated commercial forming metallic coated Drawing ............................... 3 panels, hot water 1365:1996 passivated/ resin coated.
G2NS steel steel with a spangled surface. It is (structural grade) Pressing ............................... 3 systems, laundry AS 1397:2001
suitable for moderate drawing and Roll forming ......................... 5 appliances
pressing, guaranteed non ageing and Welding................................ 4
free from stretcher strain. G2NS steel Painting (pre-treatment)...... 5
is skin passed to improve surface
quality. Skin passed material is
used to supply COLORBOND® steel
and is not available without the
COLORBOND® steel paint finish.
ZINCALUME® G250 steel is a hot-dipped zinc/ BlueScope Steel Bending................................ 5 Structural AS/NZS 1.2 to ) 1.6 Up to 1000 Surface finish spangled
G250 steel aluminium alloy-coated structural metallic coated Drawing ............................... 2 sections, rain 1365:1996 passivated/ resin coated.
G250S steel steel with a regular spangled (structural grade) Pressing ................................1 water goods AS 1397:2001
surface and guaranteed minimum Roll forming ......................... 5
yield strength of 250 MPa with Welding................................ 5
good ductility. Suitable for roll Painting (pre-treatment)...... 5
forming to an internal diameter of
0t. G250S steel is skin passed to
improve surface quality. It is normally
available only as the substrate for
COLORBOND® steel.
ZINCALUME® G450 steel is a hot-dipped zinc/ BlueScope Steel Bending................................ 3 Structural AS/NZS *1.5 to )1.6 Up to 1000 Surface finish spangled
G450 steel aluminium alloy-coated structural metallic coated Drawing ............................NR sections 1365:1996 passivated/ resin coated.
steel with a spangled surface and a (structural grade) Pressing ............................NR AS 1397:2001
guaranteed minimum yield strength Roll forming ......................... 4
of 450 MPa with limited ductility. Welding................................ 4
Suitable for roll forming to a minimum Painting (pre-treatment)...... 5
internal diameter of 4t.
ZINCALUME® A hot-dipped zinc/aluminium BlueScope Steel Bending................................ 2 Patio posts AS/NZS 1 to <1.5 Up to 1220 Surface finish spangled
G500 steel alloy-coated structural steel with a metallic coated Drawing ............................NR 1365:1996 passivated/ resin coated.
G500S steel spangled surface and a guaranteed (structural grade) Pressing ............................NR AS 1397:2001
minimum yield strength of 500 MPa Roll forming ......................... 3
with limited ductility. Suitable for Welding................................ 4
roll forming to a minimum internal Painting (pre-treatment)...... 5
diameter of 4t. G500S steel skin
passed to improve surface quality.
Skin passed material is used to
supply COLORBOND® steel and is not
available without the COLORBOND®
steel paint finish.
TRUECORE® TRUECORE® G450 steel is BlueScope Steel Bending................................ 3 Residential house AS/NZS 1.5 to 1.6 Up to 1000 Surface finish spangled
G450 steel manufactured using blue tinted metallic coated Drawing ............................NR framing where 1365:1996 passivated/ resin coated.
resin and metal coated steel. It (structural grade) Pressing ............................NR the product is not AS 1397:2001
is specifically designed for the Roll forming ......................... 4 visible
residential house framing market. Welding.................................4†
Painting (pre-treatment)...NR
TRUECORE® TRUECORE® G500 steel is BlueScope Steel Bending................................ 2 Residential house AS/NZS 1.15 to 1.2 Up to 1200 Surface finish spangled
G500 steel manufactured using blue tinted metallic coated Drawing ............................NR framing where 1365:1996 passivated/ resin coated.
resin and metal coated steel. It (structural grade) Pressing ............................NR the product is not AS 1397:2001
is specifically designed for the Roll forming ......................... 3 visible
residential house framing market. Welding.................................4†
Painting (pre-treatment)...NR
TRUECORE® TRUECORE® G550 steel is BlueScope Steel Bending.................................1 Residential house AS/NZS 0.42 to 1 Up to 1200 Surface finish spangled
G550 steel manufactured using blue tinted metallic coated Drawing ............................NR framing where 1365:1996 passivated/ resin coated.
resin and metal coated steel. It (structural grade) Pressing ............................NR the product is not AS 1397:2001
is specifically designed for the Roll forming ......................... 3 visible
residential house framing market. Welding.................................4†
Painting (pre-treatment)...NR
ZINC HI-TEN® G450 steel is a hot-dipped zinc coated BlueScope Steel Bending................................ 3 Purlins, structural AS/NZS * 1.5 to )3.2 Up to 1250 Surface finish spangled
G450 steel structural steel with a spangled metallic coated Drawing ............................NR decking, 1365:1996 passivated.
G450S steel surface and guaranteed minimum (structural grade) Pressing ............................NR scaffolding AS 1397:2001 Optional: minimal spangle.
yield strength of 450 MPa. ZINC Roll forming ......................... 4 (Optional conditions may
HI-TEN® G450S steel is skin paseed Welding................................ 5 be subject to dimensional
to improve surface quality. The skin Painting (pre-treatment)...... 5 restrictions)
passed product is only available up to
2mm thick.
ZINC HI-TEN® A hot-dipped zinc coated structural BlueScope Steel Bending................................ 2 Structural AS/NZS > 1 to <1.5 Up to 1250 Surface finish spangled
G500 steel steel with a spangled surface and metallic coated Drawing ............................NR sections, 1365:1996 passivated.
G500S steel guaranteed minimum yield strength of (structural grade) Pressing ............................NR house framing, AS 1397:2001 Optional: minimal spangle.
500 MPa. Suitable for roll forming to Roll forming ......................... 3 agricultural posts (Optional conditions may
a 4t minimum internal diameter. ZINC Welding................................ 5 and trellises be subject to dimensional
HI-TEN® G500S steel is skin passed Painting (pre-treatment)...... 5 restrictions)
to improve surface quality.
ZINC HI-TEN® A hot-dipped zinc coated structural BlueScope Steel Bending.................................1 Roll formed AS/NZS * 0.3 to )1 Up to 1250 Surface finish spangled.
G550 steel steel with a spangled surface and metallic coated Drawing ............................NR decking and 1365:1996
G550S steel guaranteed minimum yield strength of (structural grade) Pressing ............................NR walling, fencing AS 1397:2001
550 MPa. Suitable for roll forming to Roll forming ......................... 3 posts and rails
a 4t minimum internal diameter under Welding................................ 5
appropriate conditions. ZINC HI-TEN® Painting (pre-treatment)...... 5
G550S steel is skin passed to improve
surface quality.
ZINCFORM® A hot-dipped zinc coated structural BlueScope Steel Bending................................ 5 Roll formed AS/NZS * 0.3 to )2.9 Up to 1525 Surface finish spangled
G300 steel steel with a spangled surface and metallic coated Drawing ............................... 3 structural sections, 1365:1996 passivated.
G300S steel guaranteed minimum yield strength (structural grade) Pressing ............................... 2 nail plate AS 1397:2001 Optional: minimal spangle.
of 300 MPa, with good ductility. Roll forming ......................... 5 (Optional conditions may
Suitable for roll forming to an internal Welding................................ 5 be subject to dimensional
diameter of 1t minimum. G300S steel Painting (pre-treatment)...... 5 restrictions)
is a skin passed steel for improved
surface quality. Only available up to
1.60mm thick.
ZINCFORM® G350 steel is a hot-dipped zinc coated BlueScope Steel Bending................................ 3 Roll formed AS/NZS * 0.4 to )1 Up to 1220 Surface finish spangled
G350 steel structural steel with a spangled metallic coated Drawing ............................... 2 structural sections 1365:1996 passivated.
surface and guaranteed minimum (structural grade) Pressing ............................... 2 AS 1397:2001 Optional: minimal spangle.
yield strength of 350 MPa, with good Roll forming ......................... 3 (Optional conditions may
ductility. Suitable for roll forming to a Welding................................ 5 be subject to dimensional
minimum internal diameter of 2t. Painting (pre-treatment)...... 5 restrictions)
ZINCANNEAL® G3NS is a matt hot-dipped zinc/ BlueScope Steel Bending................................ 5 Non-exposed AS/NZS 0.6 to 1.6 Up to 1200 Surface finish smooth
G3NS steel iron alloy-coated drawing steel metallic coated Drawing ............................... 3 painted panels, 1365:1996 matt phosphated.
guaranteed non ageing and free from (formable grade) Pressing ............................... 3 washing machines, AS 1397:2001 Optional: unphosphated/
stretcher strain. Some powdering of Roll forming ......................... 5 acoustic ceiling oiled.
the coating may occur with severe Welding................................ 5 tiles, door frames, (Optional conditions may
deformation. Painting (pre-treatment)...... 5 switchboards, be subject to dimensional
commercial restrictions)
refrigerators and
freezers
COLORBOND® COLORBOND® Insulated Panel ZINCFORM® N/A Coolroom panels. Substrate 0.6 to 0.7 Up to 1260
Insulated steel, designed by BlueScope Steel, G300S Z275 BF For material AS 1397:2001
Panel steel specifically for the manufacture of steel selection advice,
sandwich panels for coolrooms. The or to determine if Paint coating
product offers excellent formability warranties apply, AS/NZS
coupled with good durability. visit the BlueScope 2728:2007
Steel website Type 3 – 4
or contact your
nearest BlueScope
Steel sales office
COLORBOND® COLORBOND® Metallic steel has ZINCALUME® N/A Exterior Substrate 0.42 to 1.2 Up to 1300
Metallic steel been designed by BlueScope Steel to G550S AZ150 applications such AS 1397:2001
provide an aesthetically distinctive steel as prestigious
“metallic” effect. architectural Paint coating
ZINCALUME® projects. For AS/NZS
G300S AZ150 material selection 2728:2007
steel advice, or to Type 3 – 4
determine if
warranties apply,
visit the BlueScope
Steel website
or contact your
nearest BlueScope
Steel sales office
COLORBOND® COLORBOND® Stainless steel Grade 430 N/A Roofing Substrate 0.42 to 0.55 Up to 1200
Stainless steel provides additional corrosion Stainless steel and walling, JIS G 4305
resistance and weatherability in 430SS550 particularly (Japanese
exterior applications. 430SS300 suited to very standard)
severe marine AS 1397:2001
and industrial
environments in Paint coating
which it provides AS/NZS
excellent corrosion 2728:2007
resistance, gloss Type 6
retention, and
colour stability.
For material
selection advice,
or to determine if
warranties apply,
visit the BlueScope
Steel website
or contact your
nearest BlueScope
Steel sales office
COLORBOND® COLORBOND® Ultra steel is ZINCALUME® N/A Exterior building Substrate 0.4 to 1 Up to 1345
Ultra steel specifically designed by BlueScope G550S AZ200 profiles in AS 1397:2001
Steel to combine long term durability steel applications
and exceptional corrosion resistance. requiring excellent Paint coating
ZINCALUME® corrosion AS/NZS
G300S AZ200 resistance 2728:2007
steel and long term Type 3 – 4
durability. Suited
to moderate to
severe marine,
and industrial
environments.
For material
selection advice,
or to determine if
warranties apply,
visit the BlueScope
Steel website
or contact your
nearest BlueScope
Steel sales office
COLORBOND® COLORBOND® XDG steel is ZINCALUME® N/A Garage and roller Substrate 0.4 to 1 Up to 1240
XGD steel specifically designed by BlueScope G2NS AZ150 doors. For material AS 1397:2001
Steel to provide high formability and steel selection advice,
outdoor performance for the garage or to determine Paint coating
and roller door industry. ZINCALUME® if warranties AS/NZS
G300S AZ150 apply, visit the 2728:2007
steel BlueScope Steel Type 3 – 4
website or contact
your nearest
BlueScope Steel
sales office
DRUMSTOCK® DRUMSTOCK® Pre-Painted steel CA45S–E steel N/A Drums for Substrate By
Pre-Painted steel is designed by BlueScope Steel transportation AS/NZS application
specifically for the manufacture and storage of 1595:1998 only
of drumstock suitable for storing products such as
chemically active materials. The fruit pulps, dairy
product exhibits good formability and products, and
combines a chemically resistant drum detergents. For
liner with a weather resistant drum material selection
outer coating. advice, visit the
BlueScope Steel
website or contact
your nearest
BlueScope Steel
sales office
XMA Exterior Exterior Manufactured Articles ZINCALUME® N/A Exterior hot Substrate 0.3 to 1.2 Up to 1350
Manufactured Pre-Painted steel, designed by G550S AZ150 water wrappers, AS 1397:2001
Articles BlueScope Steel for outdoor durability steel air conditioner
Pre-Painted steel and formability. panels and Paint coating
ZINCALUME® garden sheds. For AS/NZS
G300S AZ150 material selection 2728:2007
steel advice, visit the Type 3
BlueScope Steel
ZINCFORM® website or contact
G300S Z275 your nearest
steel BlueScope Steel
sales office
IFS Interior Interior Furniture and Shelving CA2S–E steel N/A Indoor furniture, Substrate Cold rolled Cold rolled
Furniture and Pre-Painted steel, designed ZINCALUME® office equipment, AS 1397:2001 0.4 to 1.2 100 to 1525
Shelving by BlueScope Steel for interior G300S AZ50 shelving. For AS/NZS
Pre-Painted steel manufactured articles having good steel material selection 1595:1998 Metallic Metallic
formability. advice, visit the coated 0.3 coated 100 to
BlueScope Steel to 1.2 1350
website or contact
your nearest
BlueScope Steel
sales office
SWP Sign Writing Sign Writing Panel Pre-Painted steel ZINCALUME® N/A Signs. For Substrate 0.5 to 1.2 Up to 1210
Panel Pre-Painted designed by BlueScope Steel. A G300S AZ100 alternative uses, AS 1397:2001
steel durable, mar resistant, high gloss steel visit the BlueScope
product with superior overpaintability Steel website Paint coating
for the signwriting industry. or contact your AS/NZS
nearest BlueScope 2728:2007
Steel sales office Type 3
SGA Superior Superior Gloss Articles Pre-Painted ZINCALUME® N/A Laundry cabinets, Substrate 0.35 to 1 Up to 1350
Gloss Articles steel designed by BlueScope Steel G300S AZ100 light fittings, AS 1397:2001
Pre-Painted steel to provide a durable, mar resistant, steel commercial
high quality surface for non-critical, refrigeration shells. Paint coating
interior appliance products. For alternative AS/NZS
uses, visit the 2728:2007
BlueScope Steel Type 3
website or contact
your nearest
BlueScope Steel
sales office
Slitting and shearing available on request from BlueScope Steel sales IMPORTANT NOTES:
offices. Material should be used promptly (within 6 months) to avoid the possibility of storage
These dimensions are a reflection of technical capability to produce. related corrosion.
Supply conditions may be subject to dimensional restrictions and is For selection of the most appropriate metallic coated steel, please refer to technical
subject to BlueScope Steel Sales and Marketing confirmation. bulletins TB1a, TB1b, CTB21 and CTB22.
Mechanical properties are guaranteed at ambient/room temperatures. Please consult
technical representatives at BlueScope Steel Sales office for high/low temperature use.
OP. 1
Pre-sales technical support BlueScope Steel Direct contact centre Your local distributor
BlueScope Steel Direct is BlueScope Steel’s Australian-based Your local distributor stocks a comprehensive range of sheet
are backed by an experienced Technical Service team that contact centre. The centre is open Monday to Friday from and coil products. They can draw on their extensive technical
operates Australia-wide. They are available to provide advice 8:30am to 5:30pm (EST) and handles a range of national knowledge of BlueScope Steel’s sheet and coil product range
about the right product to use for particular applications. technical enquiries. It receives over 2000 phone calls, emails to help you make the right product selection for your end use
and web enquiries a month from a wide range of individuals application. Their local processing facilities slit and sheer
Additionally, they can provide advice about the use of sheet and and companies including architects, engineers, designers, products to suit small unit orders and resize steel to suit your
coil products in corrosive environments, or help select specific distributors and home owners. transport and varied end use processing requirements.
products for particular manufacturing processing requirements.
Each member of the contact centre team is a trained product Local distributors also offer additional services such as order
or application expert. Where information exceeding a phone management, product storage, credit terms and same day or
Post-sales technical support enquiry is needed, the call is directed to an appropriate next day delivery. Talk to your local distributor to see how their
Typical post-sales assistance may involve customer processing Technical Service representative. flexible supply and service offer can support your business.
issues and queries about appropriate sheet and coil products
for use in conjunction with new machinery. Processing queries Outside normal business hours, a voicemail message service To locate your nearest sheet and coil distributor, use the
are typically related to press forming, roll forming, joining and and 24 hour web enquiry system are available. ‘Supplier Locater’ tool on the BlueScope Steel website at
fastening, shearing and slitting, plasma/laser cutting, welding www.bluescopesteel.com.au
and finishing (painting, enamelling, metal coating). Phone BlueScope Steel Direct on: 1800 022 999.
Dimensional tolerances:
W H
Measurement of Edge Camber Figure 2 measurement of camber – using straight-edge Measurement of Out-of-Square
AS/NZS 1365:1996 W=width, L=length, H=deviation AS/NZS 1365:1996
Camber is the lateral departure of the edge of sheet or The deviation from squareness of a length cut from trimmed-
strip from a straight line forming a chord. edge steel strip is measured by scribing a line normal to
the trimmed edge adjacent to the cut. The out-of-square is
W
When sheet or strip is laid on a flat horizontal surface expressed as a percentage of the measured value of deviation
and straight-edge placed at the concave side edge, the camber from square divided by the nominal width (see Figure 4).
maximum distance between the side edge and the straight-
L
edge is the camber (see Figure 2). Figure 4 measurement of out-of-square
W=nominal width, U=deviation from square
Camber can also be measured by placing adjacent sheets Figure 3 measurement of camber – using two lengths
or pieces of the same length of strip with concave edges W=width, L=length, H=deviation
together (see Figure 3). Actual camber is one half of the
maximum distance between the two edges. Camber
is a measured value divided by length, expressed as a W
percentage. W
camber x 2
U U
Width Tolerances
AS/NZS 1365:1996
Untrimmed Edge
Width Tolerance mm
Specified Width mm plus minus
> 599 ) 1000 25 0
> 1000 ) 1250 30 0
> 1250 ) 1500 35 0
> 1500 ) 2000 40 0
Length Tolerances
AS/NZS 1365:1996
All Edge Conditions
Length Tolerance mm
Specified Length mm plus minus
< 2000 10 0
* 2000 < 4000 15 0
* 4000 < 6000 20 0
* 6000 < 12000 30 0
* 12000 50 0
Flatness Tolerances
AS/NZS 1365:1996
All Edge Conditions
Flatness tolerances given are applicable to sheet steel having a specified carbon Steepness Ratio
content equal to 0.25% or less and a specified or typical minimum yield strength AS/NZS 1365:1996 and AS 1548:1995
less than 340 MPa. For sheet and strip > 340 MPa specified or typical minimum
yield strength, the flatness tolerance is determined by multiplying the values given
This is an alternative method for expressing flatness.
in the table by a factor of 1.5.
Note: The tolerances apply when measured at least 20 mm from the longitudinal
edges and 100 mm from the transverse edges.
Note: Class A – measured at a minimum of 50 mm from the strip edge. Within *The coating mass in this column was used for thickness calculations and includes the manufacturing
10mm of welds and coil ends, the thickness may vary by twice the above margin needed to achieve the specified minima.
tolerance.
Theoretical coating thickness for Z and ZF coatings have been based on 100g/m 2 = 0.014 mm and for
Class B – thickness measured not closer than 10 mm to the edge of the strip. AZ coatings 100g/m 2 = 0.027 mm.
There is no change of tolerance in the vicinity of welds or coil ends. Class B
tolerances are applicable to trimmed edge material only.
Width Tolerances AS/NZS1365:1996 Trimmed Edge – Class A Width Tolerances AS/NZS1365:1996 Untrimmed Edge
Width Tolerance mm Width Tolerance mm
Specified Width mm plus minus Specified Width mm plus minus
) 150 1.00 0 > 599 ) 1000 25 0
> 150 ) 300 1.50 0 > 1000 ) 1250 30 0
> 300 ) 450 2.00 0 > 1250 ) 1500 35 0
> 450 ) 600 2.50 0 > 1500 ) 2000 40 0
> 600 ) 750 3.00 0
> 750 ) 1000 4.00 0
> 1000 ) 2000 5.00 0
Width Tolerances
AS/NZS1365:1996 Trimmed Edge – Class B
Width Tolerance mm
Strip Sheet
Specified Thickness mm
<1.00 *1.00 )3.00 >3.00 All
Specified Width mm plus minus plus minus plus minus plus minus
Out-of-Square Tolerances
AS/NZS 1365:1996
For all sizes, the cut lengths shall be such that sheets of the ordered nominal dimensions can be
obtained. The out-of-squareness of a cut length of trimmed-edge steel strip shall not exceed 1.0%.
Refer to page 38.
Test certificates
Page 1 of 1
The steel supplied by BlueScope Steel is certified to the steel grade TEST CERTIFICATE Certificate No. : 14043WPD/10
Transmission Date: 25/02/10
originally ordered. Many products are tested and certified on the basis of
Customer: BLUESCOPE STEEL SSC-NSW Supplier: BlueScope Steel Limited
batch testing, where a particular coil from a group of coils is tested. P O BOX 144
GREENACRE NSW 2190
WESTERN PORT, VIC, AUSTRALIA
A.B.N. 16 000 011 058
MOI No: 318018
Cust Order No: 318018 Printed At: Supplier MWS
on: 19/08/2010
If an application requires testing of each coil in a batch, this can be done PRODUCT: XTRAFORM(R) 500 PICKLED,MILL EDGE SPECIFICATION: AS/NZS1594
if requested when the order is placed. The identity of the product should CHEMICAL ANALYSIS (Chemical Analysis supplied by the Steelmaker. Basic Oxygen Steelmaking process.)
Item Dimensions PACK CHEMICAL COMPOSITION PERCENT
COMMENTS
This test certificate is issued subject to the Uncertainty of Results statement set out on BlueScope Steel's Website www.bluescopesteelconnect.com. In order to rely upon this certificate, you must read
the Uncertainty of Results statement.
Hardness reported on customer request following BlueScope Steel Standard Procedure WQID10-M021P Coating Mass measured according to BlueScope Steel Standard Procedure C-TT04-015 Sampling - As
Recieved from production units.
I certify that the original records of the company show that the item(s) referred to on this certificate conform to the specification as stated and that the product test results on this certificate supercede product test
results on any other certificate.
Queensland Victoria and Tasmania Western Australia General enquiries about BlueScope Steel
Telephone (07) 3845 9300 Telephone (03) 9586 2222 Telephone (08) 9365 6665 and BlueScope publications.
Facsimile (07) 3845 9393 Facsimile (03) 9586 2441 Facsimile (08) 9365 6601 Free Call 1800 022 999
Address PO Box 302, Address PO Box 139, Address PO Box 618, Free Fax 1800 800 789
Acacia Ridge QLD 4110 Braeside VIC 3195 WelshpooI BC WA 6986
76 Lysaght St, 207-213 Governor Road, 650 Abernethy Road, BlueScope Steel Direct’s services are available
Acacia Ridge QLD 4110 Braeside VIC 3195 Forrestfield WA 6986 Mon-Fri from 8am to 6pm [AEST]
www.bluescopesteel.com.au
New South Wales/ACT South Australia and Northern Territory
steeldirect@bluescopesteel.com.au
Telephone (02) 4275 4999 Telephone (08) 8243 7333
Facsimile (02) 4275 4998 Facsimile (08) 8243 7304
Mailing Address
Address PO Box 1854, Address PO Box 59,
Locked Bag 8825,
Wollongong NSW 2500 Rosewater East SA 5013
South Coast Mail Centre NSW 2521
Five Islands Road, 69 Wingfield Road,
Port Kembla NSW 2500 Wingfield SA 5013
International Tel: 612 4222 3456
International Fax: 612 4222 3434
AGEING – changes in properties of steel the breakdown of the surface layer of resin, of the dried paint film on the surface HARDNESS – the resistance offered by a
occurring with the passage of time affecting releasing pigment particles and fillers normally of primer under the topcoat. It is measured metallic material to plastic deformation by
the mechanical properties of a metal or bound by resin. This normally occurs after in micrometers (um). indentation or penetration.
alloy. Usually accelerated by an increase long-term exposure to sunlight.
in temperature, and so may be artificial or DUCTLITY – relative ability of metal to deform LOCK FORMING – the forming of two
natural. CHATTER – transverse series of marks or from a flat condition into a more complex shape adjacent edges prior to interlocking.
lines in either the metal surface of the paint without fracture.
ANNEALING – a process involving heating film caused by vibration or eccentric rolls in LOCK SEAMING – the closing of a tight
and cooling, applied usually to induce processing equipment. ELASTICITY – property of material, which seam of lock formed edges of sheet metal, for
softening. The term annealing is also used to causes it to resume its original form after a example Pittsburg lock seam, grooved single
cover treatments to: COIL – rolled up length of steel strip. removal of a load. lock seam, snap lock seam.
U Remove stresses
U Alter mechanical or physical properties COATING MASS – ability of metallic coated ELONGATION – in tensile testing, the LUSTRE – lustre finish is a smooth finish for
U Produce a definite microstructure, and sheet and coil product to withstand corrosion increase in the gauge length measured after electroplating achieved by using specially
U Remove dissolved gases in a particular environment is a function of the fracture of the test specimen within the gauge prepared rolls. Some surface preparation by
amount (and type) of coating on the surface length, usually expressed as a percentage of the plater may be necessary.
CARBON STEEL – steel, free from of the steel base. This is quantified as the the original gauge length.
intentionally added alloying elements, “coating mass” and is the mass of coating on MATT – cold rolled products are available
depending for its properties substantially upon both sides of the steel base expressed in FLATNESS – absence of waviness or buckles. with either matt or lustre finish. The matt
its carbon content alone. Manganese up to grams per square metre (g/sm). The out-of-flatness of a sheet is the measured finish is produced by rolling with mechanically
1% is not regarded as removing the steel from height of the buckles from a flat surface on roughened rolls. It is preferred for lacquering
this designation. CORROSION – destruction of a metal by which the sheet is lying. and beneficial during drawing operations
electro-chemical reaction in its environment. when used with a lubricant. It is the assumed
CHALKING – chalk-line formation on the FORMABILITY Y – the relative ease with which a surface if it is not specified in the order.
surface of an organic coating caused by DRY FILM THICKNESS – thickness metal can be shaped through plastic deformation.
Tables contain dimensions that are a reflection of the technical production capability. Supply conditions may be subject to dimensional restrictions and are subject to BlueScope Steel Sales and Marketing confirmation.
This information is provided by way of general information only, and should not be relied upon by any person. BlueScope Steel makes no representation concerning the fitness for purpose of any product. You must seek specific advice as to the
suitability of a product for the purpose for which, and the manner in which, you propose to use it. This may involve further independent analysis and testing. BlueScope Steel Limited and its related bodies corporate take no responsibility for any
adverse consequences of any nature which arise as a results of reliance on the information in this document. These tables may be updated from time to time. It is your responsibility to ensure you are using the most up-to-date version.
XTRAFORM®, BRIGHTFORM®, DECKFORM®, GALVABOND®, GALVASPAN®, ZINC HI-TEN®, ZINCFORM®, TRUECORE®, ZINCALUME®, ZINCANNEAL®, COLORBOND®, Coolmax®, Permagard®, AQUAPLATE® and DRUMSTOCK® steel are registered
trademarks of BlueScope Steel. BlueScope is a trademark of BlueScope Steel Limited. BlueScope Steel Limited ABN 16 000 011 058.