Академический Документы
Профессиональный Документы
Культура Документы
INFRA S T R U C T U R E L I G H T I N G
Infrastructure of the city defines its identity. Infrastructure Lighting
lights not just illuminate but very gracefully merge with the surroundings
Street Architecture has now become the need of the day, which is
designed luminaires.
Illuminance Calculation
Symmetric
The average illuminance for a defined area can be calculated using
Recommended lux level for Road Lighting as per IS : 1944 (Parts I and II) – 1970
CLASSIFICATION TYPE OF ROAD Eavg Emin/ Emin/Eavg TYPE OF
OF LIGHTING (Iux) Eavg (%) LUMINAIRE
INSTALLATION PREFERRED PERMITTED
Important & fast
Group A1 30 0.4 33 Cut-off Semi- Cut-off
traffic route
Main road with mixed traffic,
Group A2 15 0.4 33 Cut-off Semi-Cut-off
city street, arterial roads
Secondary road, traffic, principal & Cut-off or
Group B1 8 0.3 20 non-cut-off
shopping street Semi-Cut-off
Photometric Classification Luminaire classification based upon following features of photometric performance:
(a) The extent to which the light from the luminaire is ‘thrown’ in the lengthwise
direction of the road is called the ‘throw’ of the luminaire.
(b) The extent to which the light is ‘spread out’ across the road is called the
90 ‘spread’ of the luminaire.
Figure Illustrates Isocandela diagram projected on road indicating the angle
max 90, in plane at right angle to the road axis, between downward vertical & the
line parallel to the road axis that just cuts the far side of the 90% Imax contour.
The value of 90 determines the ‘spread’ of the luminaire and max its ‘throw’.
beam
axis 90% I max Definition of the CIE classification system for the photometric
properties of luminaires
Throw Spread
Short _max < 60 0
Narrow _90 < 450
Intermediate 60 ≤ _max ≤ 70
0 0
Average 45 ≤ _90 ≤ 550
0
n
s
The prime objectives of road lighting are
• To improve the visibility to facilitate the flow of traffic and pedestrian.
• Reduction in night time accidents.
• Aid to police protection.
P • Promotion of business and industry during nighttime hours.
o • Inspiration for community spirit and growth.
p
Mounting height:
i c Vertical distance between the centre of the luminaire and the surface of the carriageway.
Spacing:
Distance measured along the centre of line of the carriageway between successive
Basic arrangements of Street Lighting: luminaires in an installation.
h= Mounting height of luminaire c = Clearance
s= Spacing between two luminaires = Angle of inclination
Outreach:
Distance measured horizontally between the centre of the column or the wall face and the
p= Outreach o = Overhang
I = Width of the road centre of the luminaire.
Overhang:
Distance measured horizontally between centre of luminaire mounted on a bracket and
adjacent edge of the carriageway.
Carriageway:
Distance between kerb lines measured at right angles to the length of the carriageway.
Kerb:
The border of stone, concrete or other rigid material formed at the edge of a carriageway.
Tilt:
Angle between the luminaire and the horizontal road reference plane.
CHOICE Features
Single piece die-cast LM6 aluminium housing and cover in epoxy powder coated
Die-cast Aluminium Streetlight Luminaire finish. Toughened flat glass cover sealed to reflector to form lamp compartment.
Bright anodized aluminium reflector with STEP profile for excellent optical control.
Provision for varying lamp positions to suit different installation parameters.
Control Gear compartment cover with bonnet type hinging arrangement for ease of
maintenance. Both end mounting as well as post top mounting arrangement
provided. Built in toe-in angle upto 15° provided for post top mounting.
Applications
Ideal for metropolitan street lighting requirements where regular maintenance is not
feasible such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66 Lamp Compartment
IP54 Controlgear Compartment
C
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSGT40IH/G HPSV-T 1 400 750 387 195 1
MHSGT40IH/G MH-T 1 400 750 387 195 1
CHOICE Features
Die-cast Aluminium Streetlight Luminaire Single piece die-cast LM6 aluminium housing and cover in epoxy powder coated finish.
Toughened flat glass cover sealed to reflector to form lamp compartment. Bright anodized
aluminium reflector with STEP profile for excellent optical control. Provision for varying
lamp positions (except for 70W HPSV) to suit different installation parameters. Control
Gear compartment cover with bonnet type hinging arrangement for ease of maintenance.
End mounting arrangement provided.
Applications
Ideal for metropolitan street lighting requirements where regular maintenance is not
feasible such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66 Lamp Compartment
IP54 Controlgear Compartment
Ordering Reference
C
CITIVISION 3 Features
Single piece die-cast LM6 aluminium housing and frame in epoxy powder coated finish. Toughened
Die-cast Aluminium Streetlight Luminaire
flat glass cover sealed to reflector to form lamp compartment. Bright anodized aluminium reflector with
STEP profile for excellent optical control. Provision for varying lamp positions (except for 70W HPSV)
to suit different installation parameters. Ballasts and Accessories mounted on gear tray for ease of
maintenance. End mounting on pipe having 60mm OD. (35-50mm OD For 70W HPSV)
Applications
Ideal for metropolitan street lighting requirements where regular maintenance is not
feasible such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66 Lamp Compartment
IP54 Controlgear Compartment
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
C
CITIVISION 2 Features
Die-cast Aluminium Streetlight Luminaire Single piece die-cast LM6 aluminium housing in epoxy powder coated finish. Clear
acrylic cover for the lamp compartment held by SS toggles. Bright anodized
aluminium reflector with STEP profile for excellent optical control. Ballasts and
Accessories mounted on detachable gear tray for ease of maintenance.
End mounting on pipe having 60mm OD. (35-50mm OD For 70W HPSV).
Applications
Ideal for expressways, arterial routes and important city roads.
Ingress Protection
IP65
C
Ordering Reference
A Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
B Type No. (W) A B C No.
SSGN1105IH HPSV-T 1 50 400 235 205 2
SSGN1107IH HPSV-T 1 70 400 235 205 2
MHSGN1107IH MH-E(clear) 1 70 400 235 205 2
SSGN1215IH HPSV-T 1 150 538 270 247 2
SSGN1125IH HPSV-T 1 250 582 312 303 2
Applications
Suitable for expressways, arterial routes and important city roads.
Ingress Protection
IP65
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
C
B
SSGN1105IH/FG HPSV-T 1 50 400 235 105 2
A
SSGN1107IH/FG HPSV-T 1 70 400 235 105 2
MHSGN1107IH/FG MH-(clear) 1 70 400 235 105 2
SSGN1215IH/FG HPSV-T 1 150 538 270 135 2
SSGN1125IH/FG HPSV-T 1 250 582 312 148 2
MHSGN1125IH/FG MH-T 1 250 582 312 148 2
MHSGN40IH/FG MH-T 1 400 695 373 170 2
SSGN40IH/FG HPSV-T 1 400 695 373 170 2
FORTUNER Features
Die-cast Aluminium Streetlight Luminaire Single piece pressure die-cast LM6 aluminium housing and cover in epoxy powder coated
finish. Toughened flat glass cover fixed to the frame by means of clamps. Bright anodized
aluminium reflector with STEP POT optics profile for excellent optical control. Ballasts
and accessories mounted on detachable gear tray for ease of maintenance.Provision for
varying lamp positions to suit different installation parameters. Both end mounting as well
as post top mounting arrangement provided.
Applications
Ideal for metropolitan street lighting requirements where regular maintenance is not
feasible such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66
Ordering Reference
C
SSGP1215IH09 Features
Single piece pressure die-cast LM6 aluminium housing and cover in epoxy powder coated
finish. Toughened curved glass cover fixed to the frame by means of clamps. Bright
anodized aluminium reflector with STEP POT optics profile for excellent optical control.
Ballasts and accessories mounted on detachable gear tray for ease of
maintenance.Provision for varying lamp positions to suit different installation parameters.
Both end mounting as well as post top mounting
Applications
Ideal for metropolitan street lighting requirements where regular maintenance is not
feasible such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66
C
Ordering Reference
A B
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSGP1215IH09 HPSV-T 1 150 580 300 180 1
MHSGP1215IH09 MH-T 1 150 580 300 180 1
SSGP1225IH09 HPSV-T 1 250 580 300 180 1
MHSGP1225IH09 MH-T 1 250 580 300 180 1
SSGP1207IH09 Features
Die-cast Aluminium Streetlight Luminaire Single piece die-cast LM6 aluminium housing and cover in epoxy powder coated finish.
Toughened curved glass cover sealed to reflector to form lamp compartment. Bright
anodized aluminium reflector for excellent optical control. Ballasts and accessories
mounted on detachable gear tray for ease of maintenance. Both end mounting as well as
post top mounting arrangement provided. Built in toe-in angle upto 15° provided for post
top mounting.
Applications
Ideal for metropolitan street lighting requirements such as important city roads, access
roads, Pathways etc.
Ingress Protection
IP66
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSGP1205IH HPSV-T 1 50 580 300 180 1
SSGP1207IH HPSV-T 1 70 580 300 180 1
LANDMARKH09 Features
Single piece pressure die-cast LM6 aluminium housing and cover in epoxy powder coated
Die-cast Aluminium Streetlight Luminaire finish. Toughened curved glass cover sealed to reflector to form lamp compartment. Bright
anodized aluminium POT optics reflector for excellent optical control. Provision for varying
lamp position to suit different installation parameters.Control Gear compartment houses a
detachable gear tray with ballast and accessories. Single toggle concept for ease of
maintenance.End mounting arrangement provided.
Applications
Ideal for metropolitan streetlighting requirements where regular maintenance is not feasible
such as expressways, arterial routes, important city roads with high traffic density.
Ingress Protection
IP66 Lamp Compartment
IP54 Controlgear Compartment
282
866
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
Suitable for 60mm
OD pipe SSGP1225IH HPSV-T 1 250 866 300 282 1
MHSGP1225IH MH-T 1 250 866 300 282 1
380
DELUX Features
A single piece deep drawn contoured aluminium housing finished in stove enamel grey from outside
Deep Drawn Aluminium Streetlight Luminaire
and white inside. A clear acrylic cover is, held in position by stainless steel toggles. Pre-anodised
aluminium parabolic side reflectors ensures high optical efficiency and wider spacing. The control
gear compartment houses copper wound VPIT ballast, and accessories mounted on a gear tray which
in turn is mounted on the cast aluminium pipe mounting arrangement from inside. Suitable for
mounting on pipe having 60mm OD(max)
Applications
Suitable for traffic routes, Access routes, perimeter lighting, etc.
Ingress Protection
IP65
C
A B Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSSD15IH HPSV(E) 1 150 545 326 260 2
SSSD25IH HPSV(E) 1 250 545 326 260 2
CITISTAR Features
Deep Drawn Aluminium Streetlight Luminaire Deep drawn aluminium housing in stove enamel grey finish. Toughened flat glass
covers both the control gear and lamp compartment. Inner surface of housing is
sand blasted and acts as POTs reflector. Ballasts and Accessories mounted on
hingeable gear tray for ease of maintenance. End mounting on pipe having 60mm
OD.
Applications
Suitable for traffic routes, access roads, perimeter lighting, etc.
Ingress Protection
IP65
C
A B Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSSG1215IH/FG HPSV-T 1 150 525 296 180 2
SSSG1225IH/FG HPSV-T 1 250 525 296 180 2
MHSSG1225IH/FG MH-T 1 250 525 296 180 2
Note: Ballast to be ordered separately.
TOWNSTAR Features
Deep drawn aluminium housing in sand blasted finish. Toughened flat glass with
Deep Drawn Aluminium Streetlight Luminaire
black screen on the portion covering the control gear compartment. Inner surface of
housing is sand blasted at bottom and aoutside and acts as POTs reflector. Ballasts
and accessories mounted on gear tray for ease of maintenance. End mounting on
pipe having 30 to 40mm OD.
Applications
Suitable for low density traffic routes, access roads, service roads, etc.
Ingress Protection
IP65
C
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSSG1207IH/FG HPSV-T 1 70 465 190 88 4
MHSSG1207IH/G MH-E 1 70 465 190 88 4
T5 STREETLIGHT Features
Deep Drawn Aluminium / MS Streetlight Luminaire Deep drawn MS / Aluminium housing in epoxy powder coated RAL 7032 grey finish. A
clear acrylic cover held in place by stainless steel toggles. Parabolic pre-anodised
aluminium reflector for better uniformity and optical efficiency. High efficiency electronic
ballasts and accessories mounted on gear tray for ease of maintenance. Die cast
aluminium mounting pipe attachment for end mounting on pipe with 50mm OD(max.).
Applications
Suitable for secondary roads, access roads, service roads, etc.
Ingress Protection
IP65
Ordering Reference
C
TOWNSTAR Features
Deep drawn aluminium housing in sand blasted finish. Toughened flat glass with
Deep Drawn Aluminium Streetlight Luminaire
black screen on the portion covering the control gear compartment. Inner surface of
housing is sand blasted at bottom and aoutside and acts as POTs reflector. Ballasts
and accessories mounted on gear tray for ease of maintenance. End mounting on
pipe having 30 to 40mm OD.
Applications
Suitable for low density traffic routes, access roads, service roads, etc.
Ingress Protection
IP65
C
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SSSG1207IH/FG HPSV-T 1 70 465 190 88 4
MHSSG1207IH/G MH-E 1 70 465 190 88 4
T5 STREETLIGHT Features
Deep Drawn Aluminium / MS Streetlight Luminaire Deep drawn MS / Aluminium housing in epoxy powder coated RAL 7032 grey finish. A
clear acrylic cover held in place by stainless steel toggles. Parabolic pre-anodised
aluminium reflector for better uniformity and optical efficiency. High efficiency electronic
ballasts and accessories mounted on gear tray for ease of maintenance. Die cast
aluminium mounting pipe attachment for end mounting on pipe with 50mm OD(max.).
Applications
Suitable for secondary roads, access roads, service roads, etc.
Ingress Protection
IP65
Ordering Reference
C
Applications
Suitable for minor routes, access roads, parking lots, perimeter lighting, etc.
Ingress Protection
IP65
C
A
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
SCEN1345/65/85/BC CFL-DF 1 45/65/85 492 197 185 4
SCEN1345/65/85/BC/AL CFL-DF 1 45/65/85 492 197 185 4
B
Applications
Suitable for illuminating Pathways, Parking areas, Access roads, Perimeter lighting etc.
Ingress Protection
IP65
SUITABLE FOR
30 to 40mm OD PIPE
C
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
LSTA181 LED 18 1 465 190 88 4
The LEMNIS 4 x 4W LED have a spatial light distribution that produces a green/blue
light to heighten visibility at night (Mesopic Vision)
Applications
Ideal for Secondary Roads, local roads,Internal factory roads, Internal roads within
campus-township, car parking, residential housing colonies, parks, pedestrian zones, etc.
Ingress Protection
IP65
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
LSL416/MP LED 4 16 457 235 105 2
Applications
deal for city roads, arterial roads where energy saving is essential during non-peak
hours. During peak hours the power saver will enable the lamp to glow at its rated
wattage (i.e. 250W) and during non-peak hours it will reduce the power to the lamp
to 150W ensuring a saving of 100W.
Ingress Protection
A
IP54
Ordering Reference
B
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
C CGRT25S HPSV 1 250 235 155 110 2
CGRT40S HPSV 1 400 235 155 110 2
Note: Few selected streetlights are also available with integral power saver device on request.
Features
Crompton Greaves Lighting offers a wide variety of Hot Dip Galvanised Octagonal poles
with a sturdy base plate. Our octagonal poles have a galvanising thickness of 80
microns (internally and externally). This protective coating ensures long life of the
product and does not require periodic painting. Octagonal poles by Crompton Greaves
have a distinct edge over conventional round stepped-wedged welded poles.
• Hot dip galvanized (80 microns) internally and externally.
• Sleek, elegant and pleasing aesthetics with flushed door.
• Bracket design as per customer requirements. (on requestat extra cost)
• Ease of maintenance.
• Does not require periodic painting.
• Long life. (Estimated life is 15 to 20 years)
Mounting Bracket
Crompton Greaves can supply galvanised arm brackets along with spigots matching with
different types of poles and as per customer requirements. Typical arrangement and
dimensional details for single arm and double arm bracket along with spigot suitable for
different types of poles given here in.
Applications
• Street Lighting
• Open area Lighting
• Yard Lighting
• Periphery Lighting
• Signage Lighting
Note: Standard essential accessories offered with streetlight poles. • Foundation bolts, anchor plate & template
TEC H N I C A L D ATA S P E C I F I C AT I O N S
Octagonal Hot Galvanised Streetlight Poles
Height Pole 5 Mtr. 7 Mtr. 9 Mtr. 9 Mtr. 10 Mtr. 11 Mtr. 12 Mtr.
(Mtrs.)
Material of BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025
Construction
Thickness 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm 3 mm
of Sheet
Thickness of 16 mm 16 mm 20 mm 20 mm 20 mm 20 mm 25 mm
Base Plate
Number of 4 4 4 4 4 4 4
Foundation Bolts
PCD of 210 x 210 mm 240 x 240 mm 240 x 240 mm 310 x 310 mm 310 x 310 mm 310 x 310 mm 350 x 350mm
Foundation Bolt
Bolt Dia 16 mm 16 mm 20 mm 20 mm 20 mm 25 mm 25 mm
Above products are available with single & double arm luminaire mounting brackets.
Note: Standard essential accessories offered with streetlight poles. • Foundation bolts, anchor plate & template
AREA LIGHTING Lighting of Outdoor spaces is essential, be it security, sports, utility or enhancing the
beauty of Building Architecture. Today, Floodlight Luminaires with HPSV, HPMV & MH
Lamps are also finding usage in specialized areas such as accent Lighting, under
canopy petrol pump lighting, monument lighting, hoarding lighting, etc.
TYPES OF FLOODLIGHT S
100%
Symmetric
80%
These have a conically shaped symmetrical beam. Both narrow and wide types are
60%
available. Symmetrical floodlights required more or less concentrated light source
such as short discharge tube of a high pressure discharge lamp. Symmetrical
40%
floodlights however, are more efficient than the asymmetrical unit when used in the
20% four corners and from the long distance.
-80.0˚ -72.0˚ -54.0˚ -36.0˚ -18.0˚ 0.0˚ 18.0˚ 36.0˚ 54.0˚ 72.0˚ 80.0˚
Maximum Intensity - 303000 cd / 27000 lm
100%
Asymmetric
80% These are available with symmetrical light distribution in the horizontal and
60%
vertical planes. In horizontal plane beam is wide while in the vertical plane it is
either wide or narrow. Asymmetrical floodlights are used in conjunction with linear
40%
light source such as halogen and tubular high intensity discharge lamp.
20%
-80.0˚ -72.0˚ -54.0˚ -36.0˚ -18.0˚ 0.0˚ 18.0˚ 36.0˚ 54.0˚ 72.0˚ 80.0˚
Maximum Intensity - 82700cd / 95000 lm
How about
Controlling City Street Lighting
with CLICK of Amazed....
Website : http://streetsmart.cgglobal.com/StreetSmart/
Street Light Automation
Technical Specifications
Product development is a continuous process at Crompton Greaves Ltd. Hence data given in the catalogue is subject to change without prior intimation.
FLOOD LIGHTING
TYPES OF FLOODLIGHT S
90º 90º
Double Asymmetric
These types of floodlights have been developed in order to obtain a
2600 uniform light distribution on the fields from only a small number of
75º
75º luminaries, without producing a glare. The design of these
5200 floodlights is such that the maximum intensity does not lie in the
centre of the beam, but is displaced towards one side.
7000
60º 60º
The fall in luminous intensity on either side of the beam axis is then
10400 so arranged that when aimed at a given point on the ground a more
or less uniform horizontal illuminance is produced. In order to limit
45º 30º 15º 0º 15º 30º 45º glare, the intensity decreases sharply from a certain angle of light
incidents, thus, making the light distribution still more asymmetric.
( Eavg X A)
N=
( x n x MF x COU )
450
500
600 Where
550 550 600
N = Number of Luminaires
500
= average illuminance level to be achieved*
600 450
500 600
550 Eavg
600
550 600 600 550 450 A = Area to be illuminated
450 600 500
= Lumen output per lamp
600 550
600
n = Number of lamp per luminaire
550
MF = Maintenance Factor
450
COU = Coefficient of Utilization
*Illumination level recommendation as per IS 3646 (Part 1): 1992
Sports Lighting
GAISF - General Association of International Sports Federation
recommendations for sports lighting is followed for both televised
and non televised competitions at various levels of sports.
Classes of play
Class I : Top level competitions, both national and international.
There are usually large number of spectator and long viewing distances.
Class II : Mid-level competition, matches are at regional or local level
with medium-sized groups of spectator and average viewing distances.
Class III : Low-level competitions and recreational sport. This normally involves
small numbers of spectators and short viewing distances.
PROFILE 1 Features
Pressure die-cast aluminium housing in powder coated black finish. Heat resistant
Asymmetric Integral Floodlight Luminaire
toughened glass fixed to housing by stainless steel toggles. Pre-anodised
asymmetric hammered finish aluminium reflector along with side reflectors for
better optical efficiency and improved vertical illumination. Control gear housing
wired with ballast and accessories. M.S cradle facilitates ease of mounting.
Applications
Suitable for hoardings, facade lighting, sports lighting, security lighting, junction lighting and
other outdoor applications requiring good vertical illumination.
B C
Ingress Protection
IP65
A
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No
Ø14 HOLE;1No. 45 45
Ø11 HOLE;2Nos.
FADT1107IH09 MH(DE) 1 70 355 245 115 2
FADT1115IH09 MH(DE) 1 150 355 245 115 2
Note: Above Luminaires with double asymmetric distribution also available (replace prefix ‘FAD’ in above cat. ref. by FDA
For example, luminaire suitable for 70W MH-T will have cat. ref. FDAT1107IH09)
FHDA24 Features
Die-cast aluminium housing in powder coated black finish. Heat resistant toughened glass
held in place by stainless steel toggles. Pre-anodised double asymmetric hammered
finish aluminium reflector along with side reflectors for better optical efficiency and
improved vertical illumination. Luminaire is pre-wired with lamp holder and mains
connector. To be used with an appropriate separate control gear box.
Applications
Suitable for areas requiring high illumination level and wide distribution such as dock
yards, outdoor switch yards, area lighting, railway marshalling yards, facade lighting, etc.
Ingress Protection
IP65
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
C
B
Type No. (W) A B C No.
FHDA24 HPSV-T 2 250 / 400 746 540 346 1
FHDA24 MH-T 2 250 / 400 746 540 346 1
PROFILE 3 Features
Pressure die-cast aluminium housing in powder coated black finish. Heat resistant
Asymmetric Integral Floodlight Luminaire
toughened glass fixed to housing by stainless steel toggles. Pre-anodised double
asymmetric hammered finish aluminium reflector along with side reflectors for better
optical efficiency and improved vertical illumination. Control gear housing wired with
ballast and accessories. M.S. cradle facilitates ease of mounting.
Applications
Suitable for hoardings, facade lighting, sports lighting, security lighting, junction lighting
and other outdoor applications requiring good vertical illumination.
Ingress Protection
IP65
B C
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
A
Note: Above Luminaires with double asymmetric distribution also available (replace prefix ‘FAD’ in above cat. ref by ‘FDA’.
For example, luminaire suitable for 400W MH-T will have cat. ref. FDAT1140IH09)
CORONA Features
Asymmetric Integral Floodlight Luminaire Pressure die-cast aluminium housing in powder coated black finish. Heat resistant
toughened glass fixed to housing by stainless steel toggles. Pre-anodised hammered
finish reflector and bright anodised side reflectors for better optical efficiency. Control
gear housing wired with ballast and accessories. M.S cradle facilitates ease of mounting.
Angle protractor on cradle facilitates aiming during installation.
Applications
Suitable for outdoor switch yards, indoor sports arena, and facade lighting.
Ingress Protection
IP65
A C
B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
FAI40IH09 HPSV-T 1 400 410 328 270 1
Ø22 HOLE;1No. 75 75
Ø14 HOLE;2Nos.
FAI40IH09/MH MH-T 1 400 410 328 270 1
KORNI 2 Features
Pressure die-cast aluminium housing in powder coated black finish. Heat resistant
Asymmetric Integral Floodlight Luminaire
toughened glass fixed to housing by means of stainless steel toggles. Pre-anodised
asymmetric hammered finish reflector and bright anodised side reflectors for better
optical efficiency. Control gear housing wired with ballast and accessories. Powder
coated M.S cradle facilitates ease of mounting. Angle protractor on cradle facilitates
aiming during installation.
Applications
Suitable for outdoor switch yards, sports arena, facade lighting, etc.
Ingress Protection
IP65
A C
B
Ordering Reference
3/4” BSC
CABLE GLAND
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
FAI1125IH09/MH HPSV-T 1 250 365 330 260 1
Ø22 HOLE;1No. 50 50
Ø14 HOLE;2Nos.
FAI1125IH/MH09 MH-T 1 250 365 330 260 1
PETROLUX Features
Double Asymmetric Integral Floodlight Luminaire Die-cast aluminium housing in powder coated black finish. Heat resistant toughened
glass fixed to housing by means of die cast aluminium frame finished in white.
Pre-anodised double asymmetric hammered finish reflector and bright anodised
side reflectors increases optical efficiency and vertical illumination. Control gear
housing wired with ballast and accessories. Suitable for recessed mounting in false
ceiling using suspension rods.
Applications
Suitable for recessed mounting with false ceiling using suspension rods for petrol pump
lighting, indoor sports lighting, etc.
Ingress Protection
IP65
C
Ordering Reference
3/4” BSC
A CABLE GLAND
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
FDAR1207IH(CA) MH(DE) 1 70 435 214 124 1
B
PETROLUX Features
Die-cast aluminium housing in powder coated black finish. Heat resistant toughened glass
Asymmetric Integral Floodlight Luminaire
fixed to housing by means of die-cast aluminium frame finished in white. Pre-anodised
asymmetric hammered finish reflector and bright anodised side reflectors for better optical
efficiency. Control gear housing wired with ballast and accessories. Suitable for recessed
mounting with false ceiling using suspension rods.
Applications
Suitable for petrol pump lighting, indoor sports arena, etc.
Ingress Protection
IP65
C
Ordering Reference
A 3/4” BSC
CABLE GLAND Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
FADR1207IH(CA) MH(DE) 1 70 435 214 124 1
FADR1215IH(CA) MH(DE) 1 150 435 214 124 1
B
380 145
FADR1425IH(CA) MH-T 1 250 430 360 192 1
FBD1425 Features
Symmetric Non-Integral Floodlight Luminaire Die-cast aluminium rear housing in powder coated black finish. Heat resistant
toughened glass fixed to housing by means of stainless steel toggle. Highly
polished spun aluminium reflector with specular finish for high optical efficiency.
To be used with an appropriate separate control gear box.
Applications
Suitable for large areas like open storage yards, railway marshalling yards,
industrial storage yards, sports arena, docks, airport aprons, construction sites,
security lighting, etc.
Ingress Protection
IP65
A B
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
FBD 1525 HPMV 1 250 520 470 - 1
FBD 1525 HPSV-E/T 1 250 520 470 - 1
3/4” BSC
CABLE GLAND FBD 1525 MH-E/T 1 250 520 470 - 1
FBD 1525 HPMV 1 400 520 470 - 1
FBD 1525 HPSV-E/T 1 400 520 470 - 1
50 50
Ø22 HOLE;1No. Ø14 HOLE;2Nos.
FBD 1525 MH-E/T 1 400 520 470 - 1
KORNI 1 Features
Pressure die-cast aluminium housing in powder coated black finish. Heat resistant
Asymmetric Non-Integral Floodlight Luminaire
toughened glass fixed to housing by stainless steel toggles. Pre-anodised asymmetric
hammered finish reflector and bright anodised side reflectors for better optical efficiency.
Pre-wired with lamp holder and mains connector. M.S cradle facilitates ease of mounting.
Angle protractor on cradle facilitates aiming during installation. To be used with an
appropriate separate control gear box.
Applications
Suitable for outdoor switch yards, docks, sports arena, facade lighting, etc.
Ingress Protection
IP65
A C
B
Ordering Reference
3/4” BSC
CABLE GLAND Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Ø22 HOLE;1No.
Type No. (W) A B C No.
FAD141409 HPSV-T 1 250/400 364 330 155 1
50 50
Ø14 HOLE;2Nos.
FAD141409 MH-T 1 250/400 364 330 155 1
Note: Suitable Convert Gear to the Ordered separately
BEAUTY Features
Symmetric Non-Integral Floodlight Luminaire Compact die-cast aluminium housing and frame in powder coated black finish. Heat
resistant toughened glass held in place by stainless steel screws. Highly polished spun
aluminium faceted reflector for high optical efficiency. Pre-wired with lamp holder and
mains connector. Powder coated M.S cradle facilitates ease of mounting and rotation in
horizontal and vertical planes. Angle protractor on cradle facilitates aiming during
installation. To be used with an appropriate separate control gear box. Also available in
integral version for 70/150W HPSV(T).
Applications
Symmetrical light distribution with narrow beam makes it ideal for facade lighting,
monument lighting, open area lighting, etc.
B
Ingress Protection
IP65
Ordering Reference
A
FHD131K Features
Die-cast aluminium housing in grey finish. Heat resistant toughened glass fixed to
Asymmetric Non-Integral Floodlight Luminaire
housing by stainless steel toggles. Anodised asymmetric aluminium reflector for better
optical efficiency. Pre-wired with lamp holder and mains connector. M.S cradle facilitates
ease of mounting. Angle protractor on cradle facilitates aiming during installation. To be
used with an appropriate separate control gear box.
Applications
Suitable for outdoor switch yards, docks, sports arena, railway marshalling yards, etc.
Ingress Protection
IP55
A C
3/4” BSC
CABLE GLAND
Ordering Reference
B
TWIN L UX Features
Asymmetric Non-Integral Floodlight Luminaire Die-cast aluminium housing in powder coated black finish.
Heat resistant toughened glass held in place by stainless steel toggles. Pre-
anodised faceted aluminium reflector and bright anodised side reflectors provided
for high optical efficiency. Pre-wired with lamp holder and mains connector. Powder
coated M.S cradle facilitates ease of mounting and rotation in horizontal and vertical
planes. Angle protractor on cradle facilitates aiming during installation. To be used
with an appropriate separate control gear box.
Applications
Suitable for areas requiring high illumination level and wide distribution such as
dock yards, outdoor switch yards, railway marshalling yards, facade lighting, etc.
Ingress Protection
A C IP65
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
B
Applications
Suitable for areas requiring high illumination level and wide distribution such as
dock yards, outdoor switch yards, railway marshalling yards, facade lighting, etc.
Ingress Protection
A
IP65
C
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
B
Ingress Protection
IP55
A C
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
B
Note: The control gear box can be mounted at a distance of 30m max. from the lamp compartment.
Applications
Ideal for expressways, arterial routes and important city roads.
Ingress Protection
IP65
A
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
B Type No. (W) A B C No.
CG1325M(CA) HPMV 1 250 244 180 106 1
CG1325S(CA) HPSV 1 250 244 180 106 1
C
Ingress Protection
IP65
Ordering Reference
A
Note: The control gear box can be mounted at a distance of 30m max. from the lamp compartment.
Ingress Protection
IP55
B C
Ordering Reference
Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
A
Ingress Protection
IP54
Ordering Reference
A C Cat Ref. Lamp Lamp Wattage Dimension (mm) Case Lot
Type No. (W) A B C No.
CG1215S HPSV 1 150 204 255 115 1
CG1215MH MH 1 150 204 255 115 1
B CG1225M HPMV 1 250 204 255 115 1
CG1225S HPSV 1 250 204 255 115 1
CG1225MH MH 1 250 204 255 115 1
CG1240M HPMV 1 400 204 255 115 1
CG1340S HPSV 1 400 204 255 115 1
Note: The control gear box can be mounted at a distance of 30m max. from the lamp compartment. CG1340MH MH 1 400 204 255 115 1
Ingress Protection
IP65
A C
Ordering Reference
B
High mast lighting as a concept in area lighting is being preferred over conventional lighting,
especially where large areas are to be illuminated without the need for numerous lighting
columns, that under certain circumstances, can be a hazard to movement. This is possible
because the high mast lighting system achieves very large space to height ratios.
Features
Our high mast is a continuously tapered, polygonal cross section of atleast 20 sides, presenting a
good and pleasing appearance which is based on proven intension design conforming to the
Technical report no.7 - 1996 of the Institution of Lighting Engineers UK, to give an assured
performance and reliable service. The structure is suitable for loading as per IS 875 (part 3) 1987.
Construction
High mast is fabricated from steel plates conforming to BS-EN 10025, cut and folded to from a polygonal
section. Masts are in two sections for 16 & 20 Mtr. and in three sections for 25 & 30 Mtr. heights having
only longitudinal weld conforming to BS 5135/AWS. The mast is provided with a fully penetrated flange
which is free from any laminations or incursions. The welded connection of the base flange is fully
developed to the strength of the entire section. The base flange is provided with supplementary gussets
between bolt holes to ensure elimination of helical stress concentration. For environmental protection of
the mast, the entire fabricated mast is Hot Dip Galvanised (Single Dip) internally and externally, having
uniform coating thickness of 85 / 65 microns for bottom / top sections respectively.
Door Opening
An adequate door opening is provided at the base of the mast. The opening is such that it permits clear
access to equipments like winch, cable, wire rope, plug & socket etc. and also facilitates easy removal of
the winch for servicing. The door opening is complete with a close fitting vandal resistant allen key
locking with provision for external lock. The door opening is carefully designed and reinforced with
EPR/PCP
Trailing Cable adequate steel section so that the mast section at the base is unaffected, and undue buckling of the cut
portion is prevented under heavy wind condition.
Flood
Dynamic Loading
Lighting Our mast structure is designed to sustain an assumed maximum reaction arising from wind speed
Luminaire
as per IS 875 (Part 3) 1987 (three seconds) which is measured at a height of 10 mtrs above
ground level. Our standard masts are suitable for a wind speed of 180 Kms/hour (50M/Sec) we
Lantern Junction Box
Carriage
can also offer masts suitable for a wind speed of 225 Kms/hr (62.5 M/sec).
Removable
Ring Support Accessories
Mast Door The high mast is provided with accessories as per customer requirements. Generally these include
a raising and lowering system (R & L), trailing cable, power tool, feeder pillar for automatic
Stainless Steel
Wire Rope switching operation of luminaires, lighting finial and aviation obstruction warning light.
Power Cable The R & L system will comprise a double drum winch, SS wire ropes, head frame and lantern
Connection carriage. The winch is self lubricating and self sustaining type. It does not require any brake or
Double
Drum Winch clutch and has a lifting capacity of SWL 750 Kgs.
Power Tool
Gusset Plate The wire ropes are of stainless steel grade AISI316 with minimum 6mm diameter and 7/19 construction.
Its central cores is also SS and have a minimum breaking strength of 2000Kgs.(Approx) The
Remote for
Up & Down power tool is integral / external type suitable for handling the total head load. It has a mechanical
Base Plate of LC torque limiter to ensure safety and also a manual handle is provided. Suitable for use in open
Foundation Hole areas, airports, railway stations, road junctions, container yards, etc.
Typical Base Compartment of A High Mast
Technical Details
HIGHMAST STRUCTURE
Nominal height of mast 12.5 Mtr. 16 Mtr. 20 Mtr. 25 Mtr. 30 Mtr.
(mtrs.) (Cat Ref.HM-11125) (Cat.Ref.HM-1116 A) (Cat Ref.HM-1220 ) (Cat.Ref.HM-1125) Cat Ref.HM-1230)
Material of Construction BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025 BSEN 10025
Normal Thickness Base Section - 3mm Base Section - 4mm Base Section - 4mm Base Section - 4mm Base Section - 5mm
Top Section - 3mm Top Section - 3mm Top Section - 3mm Middle Section - 4mm Middle Section - 4mm
Top Section - 4mm Top Section - 4mm
Cross Section of Mast 12 Sided Polygon 20 Sided Polygon 20 Sided Polygon 20 Sided Polygon 20 Sided Polygon
Length of Individual Section Base Section - 6.5 mtrs Base Section - 8.375 mtrs Base Section - 10.375 mtrs Base Section - 8.75 mtrs Base Section - 10.50 mtrs
(Approx) Top Section - 6.5 mtrs Top Section - 8.375 mtrs Top Section - 10.375 mtrs Middle Section - 8.75 mtrs Middle Section - 10.50 mtrs
Top Section - 8.75 mtrs Top Section - 10.50 mtrs
Base & Top Diameter Base Dia- 340 mm Base Dia- 350 mm Base Dia-460 mm Base Dia-485 mm Base Dia-600 mm
(Approx.) Top Dia - 150 mm Top Dia - 150 mm Top Dia - 150 mm Top Dia - 150 mm Top Dia - 150 mm
(Note: No circumferential weld is allowed)
Size of Base Flange Diameter Diameter - 540 mm Diameter - 540 mm Diameter - 670 mm Diameter - 730 mm Diameter - 730 mm
& Thickness (Approx) Thickness - 20 mm Thickness - 25 mm Thickness - 25 mm Thickness - 30 mm Thickness - 30 mm
Details of Template P. C. D. - 440 mm P. C. D. - 460 mm P. C. D. - 590 mm P. C. D. - 650 mm P. C. D. - 730 mm
No. of Foundation Bolt 6 Nos. 8 Nos. 12 Nos. 12 Nos. 16 Nos.
No. of Foundation Bolt 6 Nos. 8 Nos. 12 Nos. 12 Nos. 16 Nos.
DYNAMIC LOADING
Max. Design Wind Speed 180 km/hr. 180 km/hr. 180 km/hr. 180 km/hr. 180 km/hr.
LANTERN CARRIAGE
Diameter of Carriage 2100 mm (Approx) 2400 mm (Approx) 2400 mm (Approx) 2400 mm (Approx) 2400 mm (Approx)
Ring (mm) Inc. Arms
Number of Joints 3 Sections 3 Sections 2 Sections 3 Sections 3 Sections
Load Carrying Capacity Approx 350 kgs Approx 500 kgs Approx 750 kgs Approx 900 kgs Approx 1250 kgs
Number of Luminaires 6 Nos. 6 to 9 Nos. 9 to 12 Nos. 9 to 12 Nos. 9 to 12 Nos.
STREET LIGHTING
CHOICE Ordering Reference LANDMARK Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
SSGT40IH/G 400 240 2.10 12.45 SSGP1225IH 250 220/240 1.3 4.6
MHSGT40IH/G 400 240 2.10 12.45 MHSGP1225IH 250 220/240 1.3 4.6
SSGP1240IH 400 220/240 2.1 4.6
CHOICE Ordering Reference MHSGP1240IH 400 220/240 2.1 4.6
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) DELUX Ordering Reference
SSGT1107IH/G* 70 240 0.46 4.35 Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
SSGT11151H/G 150 240 0.74 7.10
SSSD15IH 150 240 0.74 11.30
SSGT1125IH/G 250 240 1.3 8.00
SSSD25IH 150 240 1.3 11.30
MHSGT1125IH/G 250 240 1.3 8.00
*70 Watt Luminaire differs in construction slightly from 150W & 250W version. CITISTAR Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
CITIVISION 3 Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) SSSG1215IH/FG 150 240 0.74 7.10
SSSG1225IH/FG 250 240 1.30 8.5
SSGUN07IH/G 70 240 0.46 4.45
MHSSG1225IH/FG 250 240 1.30 8.5
SSGUN15IH/G 150 240 0.74 7.4
SSGUN25IH/G 250 240 1.30 8.3 TOWNSTAR Ordering Reference
MHSGUN25IH/G 250 240 1.30 8.3 Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
SSGUN40IH/G 400 240 2.10 11.9
SSSG1207IH/FG 70 240 0.46 3.3
MHSGUN40IH/G 400 240 2.10 11.9
MHSSSG1207IH/G 70 240 0.46 3.3
FLOOD LIGHTING
PROFILE 1 Ordering Reference TWIN LUX Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FADT1107IH09 70 240 0.46 4.75 FHD1524 250 240 2X3.0 7.0
FADT1115IH09 150 240 0.74 5.25 FDH1524 250 240 2X3.0 7.0
FDH1524 400 240 2X4.3 7.0
FHDA24 Ordering Reference
FHD1524 400 240 2X4.3 7.0
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FHD1624 Ordering Reference
FHDA24 250/400 240 1.3 9.8
FHDA24 250/400 240 1.3 9.8 Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FHD1624 250 240 2x3.0 7.65
PROFILE 3 Ordering Reference
FHD1624 250 240 2x3.0 7.65
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) FHD1624 400 240 2x4.3 4.6
FDAT1125IH09 250 240 0.46 5.0 FHD1624 400 240 2x4.3 4.6
FDAT1125IH09/S 250 240 0.74 6.0
FDAT1140IH09
FDAT1140IH09/S
400
400
240
240
2.10
2.10
10.45
10.45 CONTROL GEAR
CORONA Ordering Reference CG BOX CG1240S(CA) Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FAI40IH09 400 240 2.10 12.25 CG1240S(CA) 400 240/220 2.10 7.4
FAI40IH09/MH 400 240 2.10 12.25 CG1240MH(CA) 400 240/220 2.10 7.4
KORNI 2 Ordering Reference CG BOX CG1325S(CA) Ordering Reference
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FAI1125IH09 250 240 1.30 9.0 CG1325M(CA) 250 240/220/200 1.32 3.88
FAI1125IH/MH09 250 240 1.30 9.0 CG1325S(CA) 250 240/220/200 2.13 4.9
CG1325MH(CA) 250 240/220 1.30 4.9
PETROLUX Ordering Reference
CG1340M(CA) 400 240/220 1.3 4.9
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FDAR1207IH(CA) 70 240 0.46 5.0 CG BOX CG1308M(CA) Ordering Reference
FDAR1215IH(CA) 150 240 0.74 6.0 Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg)
FADR1425IH(CA) 250 240 1.30 9.0 CG1307S(CA) 70 240/220 0.46 3.02
PETROLUX Ordering Reference CG1307MH(CA) 70 240/220 0.46 3.02
Cat Ref. Wattage (W) Voltage (V) Current (A) App. Wt.(Kg) CG1308M(CA) 80 240/220/200 0.43 2.95
FDAR1207IH(CA) 70 240 0.46 4.75 CG1312M(CA) 125 240/220/200 0.66 3.0
FDAR1215IH(CA) 150 240 0.74 5.75 CG1315S(CA) 150 240/220 0.74 3.6
FDAR1425IH(CA) 250 240 1.3 9.20 CG1315MH(CA) 150 240/220 0.74 3.6
EASTERN REGION
Kolkata : 50, Chowringhee Road, Kolkata - 700 071. (033) 22829681-22829685, 22994218
Patna : Eastern Logistic, Sahyogi Press Marg Exhibition Road,Patna-800 001. (0612) 3261594,3261595 2229531
Bhubaneshwar : Janpath Tower, 3rd Floor, Ashok Nagar, Unit II, Bhubaneshwar - 751 009. (0674) 2531128, 2531429 2533521
Guwahati : C/o. Assam Investment & Construction Co., GS Road, Dispur, (0361) 2344709,2341221 2340775
Ganeshguri (Nr. Car Ghar), Guwahati - 781 005.
Ranchi : C/o. Ess Ess Agencies, Upahar Cinema, Campus,Ratu Road, Ranchi - 854005. (0651) 2512095 2512095
WESTERN REGION
Mumbai : Crompton Greaves Ltd. Kanjurmarg (East), Mumbai - 400 042. (022) 67558622,67558626 25795158
Ahemdabad : 909, Sakar-II, Near Ellisbridge Police Stn., Ahemdabad-380 036. (079) 40012000,40012201 40012222
Indore : 103-B, Apollo Trade Centre, 2-B, Rajgarh Kothi, (0731) 2498269, 2498271 4065621
Mumbai-Agra Road, Indore - 452 001.
Nagpur : 3, West High Court, Dharam Peth, Nagpur - 440 010. (Satellite Off.) (0712) 2531271,2560870 2537196
Baroda : 10A, Vrindavan Colony, Near Har nagar, Water Tank, Gotri Road, Baroda - 390 007. (0265) 2332460, 2332227 2332458
Pune : Premium Point Building, 4th Floor, J.M. Road, Shivaji Nagar, Pune - 411 005. (020) 25534675,25534677 25534684
Raipur: 5, New Tilak Nagar, Beside Sai Care Hospital, Avanti Vihar, Raipur -492 001 (0771) 4022214,4022215 2444577
SOUTHERN REGION
Chennai : 3A, Kodambakkam High Road, P.B.No. 3316, Nungambakkam, Chennai - 600 034. (044) 42247500,44247575 28231973
Bangalore : 1st Floor, Janardhan Towers, 562/640, (080) 41391908,41391909 41391900
Bannerghatta Main Road, Bilekahalli, Bangalore-560 076.
Cochin : Cherupushpam building, 5th Floor,300-6, (0484) 2370860, 2370863 2373728
Shanmugham Road, Ernakulum, Cochin-682 031.
Secunderabad : Minerva Complex, 94, Sarojinidevi Road, Secunderabad-500 003. (040) 40002300,40002347 40002340
Coimbatore : 658/664, RajLaxmi Plaza, 100 Feet Road, (0422) 2526453,2521830 2525334
Gandhipuram, Coimbatore-641 037. (Satellite Off.)
Madurai : 2/3, Mangayakarsi Women’s College Road, Paravai, Madurai-625 402. (Satellite Off.) (0452) 2667771 2667772
Registered Office:
CG House, 6th Floor, Dr Annie Besant Road, Worli, Mumbai - 400 030, India
W: www.cgglobal.com
Care has been taken to ensure that the information contained within is correct. Photograph shown here in are indicative. Owing to continuous innovation and improvements, the actual product when supplied, may
differ from the details given here in. Crompton Greaves Limited reserves the right to make changes in the data/details without prior notice.