Вы находитесь на странице: 1из 24

TABLE OF CONTENTS

ORIGINAL HARDCAST TWO PART DUCT SEALING SYSTEM

RTA-50 (Sealant; Indoor/Outdoor)............................................................Page 2


DT-5300/5400 Tape............................................................................................... 2
TWO PART II (Application Guide)...................................................................... 3
TWO PART II (Sealant)........................................................................................ 3
TWO PART II (Tape set-up guide)....................................................................... 4

MASTIC DUCT SEALANTS

IRON-GRIP 601 (Indoor/Outdoor [UL 181-BM LISTED])................................... 5


FLEX-GRIP 550 (Indoor/Outdoor [UL 181-BM LISTED])................................... 6
SPRAY-SEAL (Indoor/Outdoor [UL 181-BM LISTED]........................................ 7
VERSA-GRIP 181 (Indoor/Outdoor [UL 181A-M/UL 181B-M LISTED])............ 8
VERSA-GRIP 102 (Indoor/Outdoor [UL 181A-M/UL 181B-M LISTED])............ 9
DUCT-SEAL 321 (Indoor/Outdoor [UL 181-BM LISTED])............................... 10
CCWI-181 (Indoor/Outdoor [UL 181A-M/UL 181B-M LISTED])........................11
SURE-GRIP 404 (Solvent [UL 181-BM LISTED])............................................. 12
COLD-SEAL (Indoor [UL 723])...................................................................... 13
Scrim.................................................................................................................. 14

ROLLED ELASTOMERIC DUCT SEALANTS

ALL-PURPOSE 1602 (Indoor)........................................................................... 15


ALUMA-GRIP 701 (Indoor/Outdoor)................................................................. 16
FOIL-GRIP 1402 (Indoor/Outdoor).................................................................... 17
FOIL-GRIP 1403 181BFX (Indoor/Outdoor [UL 181 B-FX LISTED])............... 18

GENERAL CONSTRUCTION SEALANTS

WATER CUT-OFF MASTIC................................................................................ 19


SILIMAX HI-TEMPERATURE SILICONE SEALANT......................................... 20
SILIMAX MULTI-PURPOSE SILICONE SEALANT...................................... 21-22
METALBOND MOISTURE CURING SEALANT................................................. 23

FIRESTOP PRODUCTS

TREMSTOP IA.................................................................................................... 24

Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
1
TWO PART II SEALING SYSTEM ™

DT-Tape with RTA-50 (INDOOR/OUTDOOR)

The Original Indoor/Outdoor Duct Sealing System


TWO PART II is Hardcast’s original mineral-gypsum-compound-impregnated fiber tape and liquid sealant duct
joint sealer. The industry standard two part system for sealing low, medium and high pressure duct systems.
TECHNICAL DATA TWO PART II PART NUMBERS
INSTALLED WITH DT-TAPE
RTA-50: 1 Case w/ (4) 1-Gallon Pails................ 304168
RTA-50 SEALANT DT-5300: 1 Case w/ (12) 3” x 150’ Rolls............ 304164
Bonding Time........................48 Hrs.* DT-5400: 1 Case w/ (12) 4” x 150’ Rolls............ 304165
Service Temperatures..........0°F to 200° F 2 Part II Dispensor: 1 Unit................................. 304286
Surface Burning (When tested in accordance with ASTM E-84)
Flame Spread.................0 APPLICATION
Smoke Developed.........0 Apply to outer surface of duct joint only
(After duct is installed)
Weather QUV . ................................ Passed 1000 hrs QUV
Pressure Classes.................. 1/2,1,2,3,4,6,10 inches w.g. Temperature.............. 35°F. to 110°F. (1.7°C to 44°C)

Seal Classes..........................All SMACNA Classes Method....................... Use 2 Part II Dispenser or brush.


Wrap wet tape around duct joint,
Mildew Resistance................Mold & Mildew Resistant smoothing out wrinkles or bubbles.
Flexibility...............................Excellent
Preparation................ Surface must be dry, dirt, oil, and
Freeze/Thaw Stability...........Passed 5 cycles (Stir before use) grease free.
VOC (Less Water)..................135 GPL Clean Up Wet............. Soap and Water
* May vary according to temperature and humidity
Clean Up Dry............. UN-TACK™ or Solvent
City of Los Angeles Approval RR#8069 (Use safe handling practices)

Painting..................... Only latex or epoxy paints


DT-TAPE STORAGE - DO NOT FREEZE
Appearance.......................... White Impregnated Fiber Tape
Temperature.............. 35°F to 110°F (1.7°C to 44°C)
Packaging............................. 150 ft. rolls in widths of:
Shelf Life .................. RTA 50 = One year (Unopened)
DT 5300.............................. 3” - 12 rolls per case DT-Tape = Not Applicable
DT 5400 ............................. 4” - 12 rols per case

Two Part II SEALANT DISPENSER


Appearance............... Combined tape roll holder / dispenser; pail
mounted design.
Construction............. Custom designed, high impact polyethylene
Capacities Tape......... 150 ft./roll of 3” or 4” DT Tape

PRECAUTIONS
Surfaces must be clean and free of moisture, contamination and For additional information contact:
foreign matter. Do not apply when rain or freezing temperatures
will occur within 72 hours. Do not apply where temperatures
will exceed 200ºF. Store DT Tape in DRY ATMOSPHERE. Keep
out of the reach of children. Review MSDS for complete safety
information prior to use. DO NOT use where acidic or alkaline
900 Hensley Lane
chemicals are present (ie., lab fume hood, vents, etc.)
Wylie, Texas 75098
For Industrial Professional Use Only. Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


2
TWO PART II SEALING SYSTEM™
APPLICATION INSTRUCTIONS
RTA-50 (Indoor/Outdoor) is specifically designed for use in conjunction with HARDCAST DT-5300, DT-5400, and DT-6100 pressure-
less tape. It is recommended for application to sheetmetal ductwork.

1. HARDCAST recommends the use of our Two Part II Dispenser. When using the dispenser, the bottom guide roller is
submerged in the sealant. The coating control roller should be adjusted to apply a liberal coating of adhesive on the tape as
it emerges from the dispenser. Only DT-5300 and DT-5400 will fit the Two Part II Dispenser.

2. Pull the tape slowly through the dispenser so that it can absorb sufficient sealant and cut to the desired length. The easiest sizes
to handle are 12” to 18” lengths which can be overlapped on each other to form a continuous band around the duct.

3. Apply the tape to duct joint with the heavier coated side down and press firmly to ensure total contact with duct surface. Work
out any air bubbles entrapped under tape. Apply tape to surface immediately after coating with sealant.

4. Apply a top coat of RTA-50 sealant over the tape with a brush.

5. IF A TWO PART II DISPENSER IS NOT AVAILABLE, THE TAPE CAN BE APPLIED USING THE FOLLOWING METHOD:

Cut the tape to the desired (manageable) length and place it on a flat surface. Using a paintbrush apply sealant directly to
both sides of the tape then apply tape to duct joint.

6. Allow a minimum of 72 HOURS drying time before turning on the system (on interior duct only).

7. After the sealant has dried a minimum of 72 HOURS, on exterior duct apply an additional coat of RTA-50 to tape surface. Drying
time may take longer depending on temperature and relative humidity conditions.

8. Coverage: Approximately 1 gallon RTA-50 per two 3” X 150’ rolls of DT-Tape.

CAUTION: Surface must be clean and free of moisture, contamination and foreign matter for best results. Do not apply when
rain or freezing temperatures will occur within 72 hours. Use only latex or epoxy based paints to cover Hardcast products.

CAUTION: If product freezes, return to room temperature and stir before use.

LEAKAGE TEST: Use smoke method only. Do not use soap and water for test.

FOR SPECIAL APPLICATIONS CONTACT HARDCAST

RTA-50
LIQUID SEALANT

CAUTION
HARMFUL IF SWALLOWED OR INHALED
Avoid breathing vapors. Keep container closed when not in use. Use with adequate ventilation. Wash thoroughly after handling. If swallowed DO NOT INDUCE
VOMITING. Call a physician. Overexposure to vapors may cause respiratory irritation. If inhaled, remove to fresh air. If not breathing, give artificial respiration.
If breathing is difficult, give oxygen. Contact a physician immediately.
MAY CAUSE SKIN IRRITATION: Prolonged or repeated contact may cause drying, brittleness, cracking or irritation. Use of impervious gloves and clothing recom-
mended. Avoid contact with skin. May be irritating to sensitive skin. Wash thoroughly after handling. In case of contact with skin, remove contaminated clothing
and thoroughly wash affected area with soap and water. Do not use if skin is broken. If rash develops, discontinue use. Contact a physician if symptoms persist.

REVIEW MATERIAL SAFETY DATA SHEET FOR COMPLETE SAFETY INFORMATION PRIOR TO USE.
CONTAINS: ETHYLENE GLYCOL

FOR INDUSTRIAL USE ONLY.


MAY NOT BE REPACKAGED OR SOLD FOR OTHER THAN INDUSTRIAL OR PROFESSIONAL USE.

KEEP OUT OF REACH OF CHILDREN

601236
Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
3
TWO PART II SEALING SYSTEM™
The original, classic Hardcast DT Tape and sealant system invented by Hardcast now comes in this new, easy to
use system. The original tape is now in 150 foot lengths to fit this dispenser. The RTA-50 liquid sealant is available
in 1 gallon pails. The combination offers the same superior seam/joint sealing used for almost 40 years in an easy
to use, easy to maintain dispenser. Save time and money and still get the best duct seal ever invented, just follow
these instructions.

A. Remove Core Roller (1) by slightly D. Pull the tape through the the holder/frame G. Pull the amount of tape needed and cut
pulling on the sides of the holder/frame. towards and over the Tape Cutting Guide (4). with a razor cutter using the Tape Cutting
Insert the Roller into a roll of Hardcast Guide (4) or use scissors.
DT Tape. Replace the Roller with the E. Remove the lid from the Hardcast RTA-50
Tape into the holder/frame. sealant pail. Place the assembled Tape and H. Apply the sealant/coated tape over the
Dispenser in place of the lid and press the duct joint. Overlap the ends of the tape and
B. Guide the leading edge of the tape rim firmly to lock it to the pail. squeeze out air bubbles. Allow to cure as
down, between the the Fixed Coating directed on the sealant label.
Control Roller (2) and the Adjustable F. Adjust the amount of sealant applied to
Coating Control Roller (3). Pull the the tape by loosening the wing nuts of the I. When not in use, remove the Tape and
tape under and around the Bottom Tape Adjustable Coating Control Roller (3) and Dispenser assembly from the pail. Close it
Guide Roller (6). moving it towards the Fixed Coating Control tightly with it’s lid. Cut the tape where it is
Roller (2) until the tape is pressed against dry, use or discard the wet tape. Clean the
C. Pull the tape up and guide it back itself to create a squeegee effect. Move the Dispenser with water.
through the two Coating Control Rollers Adjustable Roller (3) away from (2) to leave
(2) & (3) and over the Adjustable Coat- more sealant on the tape. Tighten the wing
ing Control Roller (3). nuts when adjusted as desired.

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


600280
4
IRON-GRIP 601
®

Complia nt with Premium Indoor/Outdoor


ir ements
LEED Requ Flexible Water Based Duct Sealant
A versatile, all purpose, fiber-free, duct sealant for use on all types of metal duct, glass fiber duct board, and flex
duct, as well as duct fabric and flexible tubing runouts. Distinguished by its ability to accommodate minor vibration
and movement, IRON-GRIP stays flexible to save call-back labor. IRON-GRIP’s excellent coverage rates and
easy brush-on application provide low installed cost while providing Hardcast’s proven reliability.

TECHNICAL DATA
Color �������������������������������������������� Gray
IRON-GRIP 601 PART NUMBERS
Consistency ������������������������������� Heavy Brush On 1 Case w/ (25) 11 oz. Cartridges.................................304137
Base �������������������������������������������� Synthetic latex
Solvent ���������������������������������������� Water 1 Case w/ (4) 1-Gallon Pails........................................304135
Weight per Gallon ���������������������� 10.7 lbs. 1 - 5-Gallon Pail...........................................................304136
Solids Content ���������������������������� 63%
Viscosity ������������������������������������� >300K cps
Coverage (per gal.) �������������������� Up to 320 lin. ft. at 3” width, 20
mil thickness APPLICATION
Shore A Hardness ���������������������� >20 Apply to entire surface of duct joint
Flexibility ������������������������������������ Passes 1/4 in. mandrel bend
Time to Test �������������������������������� 48 hours* Temperature �������������������� 35°F. to 110°F. (1.7°C to 38°C.)
Service Temperature ������������������ -20°F to 200°F
Water Resistance ����������������������� Excellent Method ����������������������������� Brush, putty knife, caulk gun,
Mildew Resistance ��������������������� Mold & Mildew resistant trowel and spray
VOC ��������������������������������������������� 75 g/l (less water) Preparation ���������������������� Surface must be dry, dirt, oil, and
Pressure Classes ����������������������� SMACNA ½ , 1, 2, 3, 4, 6 and 10 grease free.
inches w.g.
Seal Classes ������������������������������� SMACNA A, B, C Rate ���������������������������������� Apply at joints and fasteners
Packaging ����������������������������������� 11 oz. cartridges, 20 mil thick wet film
1 gal., 5 gal. pails Clean Up Wet ������������������� Soap and water
Freeze/Thaw Stability ���������������� Passed 5 cycles
Specifications Compliance ��������� Passes ASTM C-731, ASTM Clean Up Dry ������������������� UN-TACK™ or Solvent
D-2202. USDA, EPA and FDA (Use safe handling practices.)
*May vary according to
temperature and humidity Approved. LEED compliant Painting ���������������������������� Only latex or epoxy paints
SCAQMD Rule 1168.
STORAGE
CAULKING AND SEALANTS Temperature �������������������� 35°F. to 110°F. (1.7°C to 44°C)
94PF DO NOT FREEZE
SURFACE BURNING CHARACTERISTICS
FLAME SPREAD....................................... 0 Shelf Life �������������������������� One year (unopened)
SMOKE DEVELOPED.............................. 0
*Applied to inorganic reinforced Cement Board *Tested as applied in Flammability �������������������� Non-flammable
one 3 in. (76.2 mm) wide strip, on center covering 16.7 percent of the
exposed test sample area) at a coverage of 80 sq. ft/ gal (2 sq. M/L).
Flash point of finished sealant, closed cup : No flash to boiling.

17NF
UL 181B-M
Mastic closure systems for use with flexible
duct systems or connectors.

City of Los Angeles Approval RR#8069

PRECAUTIONS For additional information contact:


Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of
children. Review MSDS for complete safety information prior to use. 900 Hensley Lane
DO NOT use where acidic or alkaline chemicals are present (ie., lab Wylie, Texas 75098
fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com
For Industrial Professional Use Only.
601237
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
5
FLEX-GRIP 550

Complia nt with
Indoor/Outdoor
ir ements Water Based Duct Sealant
LEE D Requ

FLEX-GRIP 550 is an all purpose, fiber-free, duct sealant for use on all types of metal duct, glass fiber
duct board, and flex duct, as well as duct fabric and flexible tubing runouts. Distinguished by its ability
to accomodate minor vibration and movement, FLEX-GRIP 550 stays flexible to save call-back labor.
FLEX-GRIP’s excellent coverage rates and easy spray and brush-on application provide low installed
cost while providing Hardcast’s proven reliability.
TECHNICAL DATA FLEX-GRIP 550 PART NUMBERS
Color �������������������������������������������� Gray
Consistency ������������������������������� Heavy Brush On/Spray Grade 1 Case w/ (25) 11 oz. Cartridges..............................304134
Base �������������������������������������������� Synthetic latex
1 Case w/ (4) 1-Gallon Pails.....................................304132
Solvent ���������������������������������������� Water
Weight per Gallon ���������������������� 10.7 lbs.
Solids Content ���������������������������� 63%
Viscosity ������������������������������������� >300K cps APPLICATION
Coverage (per gal.) �������������������� Up to 320 lin. ft. at 3” width, 20
mil thickness Temperature �������������������� 35°F. to 110°F. (1.7°C to 38°C)
Shore A Hardness ���������������������� >20 Method ����������������������������� Brush, putty knife, caulk gun,
Flexibility ������������������������������������ Passes ¼ in. mandrel bend trowel or spray.
Time to Test �������������������������������� 48 hours*
Preparation ��������������������� Surface must be dry, dirt, oil, and
Service Temperature ������������������ -20°F to 200°F
Water Resistance ����������������������� Excellent grease free.
Mildew Resistance ��������������������� Mold & Mildew resistant Rate ���������������������������������� Apply at joints and fasteners 20
VOC ��������������������������������������������� 75 g/l (less water) mil thick wet film
Pressure Classes ����������������������� SMACNA ½ , 1, 2, 3, 4, 6 and 10
Clean Up Wet ������������������ Soap and water
inches w.g.
Seal Classes ������������������������������� SMACNA A, B, C Clean Up Dry ������������������� UN-TACK™ or Solvent
Packaging ����������������������������������� 11 oz. cartridges & 1 gallon pails. (Use safe handling practices.)
Freeze/Thaw Stability ���������������� Passed 5 Cycles
Painting ��������������������������� Only latex or epoxy paints
Specifications Compliance ��������� Passes ASTM C-731, ASTM
D-2202. USDA, EPA and FDA STORAGE
*May vary according to Approved. LEED compliant Temperature �������������������������35°F. to 110°F. (1.7°C to 44°C)
temperature and humidity SCAQMD Rule 1168. DO NOT FREEZE
Shelf Life ������������������������� One year (unopened)
CAULKING AND SEALANTS Flammability ������������������� Non-flammable
94PF
SURFACE BURNING CHARACTERISTICS
FLAME SPREAD....................................... 0
SMOKE DEVELOPED.............................. 0
*Applied to inorganic reinforced Cement Board *Tested as applied in
one 3 in. (76.2 mm) wide strip, on center covering 16.7 percent of the
exposed test sample area) at a coverage of 80 sq. ft/ gal (2 sq. M/L).
Flash point of finished sealant, closed cup : No flash to boiling.

17NF
UL 181B-M
Mastic closure systems for use with flexible
duct systems or connectors.

City of Los Angeles Approval RR#8069

PRECAUTIONS For additional information contact:


Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of
900 Hensley Lane
children. Review MSDS for complete safety information prior to use.
DO NOT use where acidic or alkaline chemicals are present (ie., lab Wylie, Texas 75098
fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com
For Industrial Professional Use Only.
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
601239
6
SPRAY-SEAL

t with Indoor/Outdoor
C omplian
LEED Requir
e ments Water Based Duct Sealant
SPRAY-SEAL is an all purpose sealant for use on all types of metal duct, glass fiber duct board, and flex
duct, as well as duct fabric and flexible tubing runouts. Distinguished by its ability to accomodate minor
vibration and movement, SPRAY-SEAL stays flexible without cracking which saves call-back labor.
SPRAY-SEAL’s excellent coverage rate and easy spray application provide low installed cost while
providing Hardcast’s proven reliability.
TECHNICAL DATA SPRAY-SEAL PART NUMBERS
Color �������������������������������������������� Gray
Consistency ������������������������������� Spray Grade 1 - 5-Gallon Pail........................................................304133
Base �������������������������������������������� Synthetic latex
Solvent ���������������������������������������� Water
Weight per Gallon ���������������������� 11.3 +/- .3 lbs. (5.126 +/- .126 kg) APPLICATION
Solids Content ���������������������������� 67% +/- 2
Temperature �������������������� 40°F to 110°F (4.4°C to 38°C)
Viscosity ������������������������������������� >60 +/- 10K cps
Coverage (per gal.) �������������������� Up to 320 lin. ft. at 3” width, Method ����������������������������� For spray, use Hardcast Sealant
Delivery System
20 mil thickness
Flexibility ������������������������������������ Passes ¼ in. mandrel bend Preparation ��������������������� Surface must be dry, dirt, oil, and
@ -25°F (-31.6°C) grease free.
Time to Test �������������������������������� 48 hours* Rate ���������������������������������� Apply at joints and fasteners 20-
Service Temperature ������������������ -20°F to 200°F (28.8°C to 93.3°C) 30 mil thick wet film
Water Resistance ����������������������� Excellent Clean Up Wet ������������������ Soap and water
Mildew Resistance ��������������������� Mold & Mildew resistant Clean Up Dry ������������������� UN-TACK™ or Solvent
VOC ��������������������������������������������� 52 g/l (Use safe handling practices.)
Pressure Classes ����������������������� SMACNA ½, 1, 2, 3, 4, 6 and 10 inches w.g. Painting ��������������������������� Only latex or epoxy paints
Seal Classes ������������������������������� SMACNA A, B, C
Packaging ����������������������������������� 5 gallon (18.9 liter) pails STORAGE
Freeze/Thaw Stability ���������������� Passed 5 Cycles Temperature �������������������� 35°F to 110°F (1.7°C to 44°C)
Specifications Compliance ��������� Passes ASTM C-731, ASTM DO NOT FREEZE
D-2202. USDA, EPA and FDA Shelf Life ������������������������� One year (unopened)
*May vary according to Approved. LEED compliant
temperature and humidity
SCAQMD Rule 1168. Flammability ������������������� Non-flammable

CAULKING AND SEALANTS


PHYSICAL PROPERTIES
94PF Property Test Method Results
SURFACE BURNING CHARACTERISTICS
FLAME SPREAD....................................... 0 Mold Resistance ASTM 5590 no growth
SMOKE DEVELOPED.............................. 0
*Applied to inorganic reinforced Cement Board *Tested as applied in
Tensile Strength ASTM 412 175 psi
one 3 in. (76.2 mm) wide strip, on center covering 16.7 percent of the Low Temp Crack Bridging ASTM 1305 Pass @ 0° F
exposed test sample area) at a coverage of 80 sq. ft/ gal (2 sq. M/L).
Flash point of finished sealant, closed cup : No flash to boiling. Low Temp Flexibility ASTM 1970 Pass @ -5° F
17NF
UL 181B-M
Mastic closure systems for use with flexible
duct systems or connectors.

City of Los Angeles Approval RR#8069

PRECAUTIONS For additional information contact:


Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of 900 Hensley Lane
children. Review MSDS for complete safety information prior to use.
Wylie, Texas 75098
DO NOT use where acidic or alkaline chemicals are present (ie., lab
fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com
For Industrial Professional Use Only.

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


7
VERSA-GRIP 181

it h
Comp liant w
uiremen ts
LE ED Req

Premium Indoor/Outdoor Water Based Duct Sealant


VERSA-GRIP 181 is a premium grade, versatile, all purpose duct sealant for use on all types of metal
duct, glass fiber duct board, and flex duct, as well as duct fabric and flexible tubing runouts. VERSA-
GRIP incorporates a built-in fiber reinforcement for exceptional strength, with UV inhibitors for outdoor
use. UL 181A-M listed / UL 181B-M listed.
TECHNICAL DATA VERSA-GRIP 181 PART NUMBERS
Color �������������������������������������� White & Gray
Consistency �������������������������� Heavy textured 1 Case w/ (25) 11 oz. Cartridges (White)....................304141
Base ��������������������������������������� Synthetic latex 1 Case w/ (25) 11 oz. Cartridges (Gray)......................305056
Solvent ���������������������������������� Water 1 Case w/ (4) 1-Gallon Pails (White)...........................304138
Weight per Gallon ���������������� 11.6 lbs. 1 Case w/ (4) 1-Gallon Pails (Gray)............................305057
Solids Content ���������������������� 70%
1 - 2-Gallon Pail (White)..............................................304139
Viscosity �������������������������������� Thixotropic
1 - 2-Gallon Pail (Gray)...............................................305058
Coverage (UL 181 A-M) �������� Apply 18 mil, scrim, addt. 18 mil
(UL 181 B-M) ������������������������� Approximately 214 to 320 lin. ft. per gal. at 1 - 5-Gallon Pail (White)..............................................304140
20 to 30 mil wet film thickness at 3” width. 1 - 5-Gallon Pail (Gray)...............................................305059
Shore A Hardness ���������������� >20
Flexibility ������������������������������� Passes ¼ inch mandrel bend APPLICATION
Time to Test �������������������������� 48 hours*
Temperature ����������������� 35°F. to 110°F. (1.7°C to 44°C)
Service Temperature ������������ -20°F to 200°F
Method �������������������������� Brush, putty knife, caulk gun, pump
Mildew Resistance ��������������� Mold & Mildew resistant
Preparation ������������������� Surface must be dry, dirt, oil, and
VOC ���������������������������������������� 45 g/l (less water)
grease free.
Surface Burning Flame Spread....................... 0
Smoke Developed................ 0 Rate (UL 181 A-M): �������� Apply 18 mil, scrim and 18 mil over scrim
(When tested in accordance with ASTM E84, UL 723)
(UL 181 B-M): ������� Approx. 214 to 320 lin. ft. per gal. at
Pressure Classes ����������������� SMACNA ½ , 1, 2, 3, 4, 6 and 10 inches w.g. 20 to 30 mil wet film thickness at 3” width.
Seal Classes ������������������������� SMACNA A, B, C Clean Up Wet ���������������� Soap and water
Packaging ����������������������������� 11 oz. cart.; 1, 2 & 5 gal. pails Clean Up Dry ���������������� UN-TACK™ or Solvent
Freeze/Thaw Stability ����������� Passed 5 Cycles (Use safe handling practices.)
Specification Compliance ��� Passes ASTM C-731, D-2202 USDA, Painting ������������������������� Only latex or epoxy paints
*May vary according to EPA & FDA Approved. LEED compliant Ductboard...................... Scrim required for UL 181A-M
temperature and humidity SCAQMD Rule 1168. STORAGE
Underwriters Laboratories Inc.®
LISTED Temperature.................. 35°F. to 110°F. (1.7°C to 44°C)
17NF DO NOT FREEZE
UL 181A-M Shelf Life ����������������������� One year (unopened)
FOR USE WITH U.L. LISTED RIGID
FIBERGLASS AIR DUCTS OR CONNECTORS. Flammability ����������������� Non-flammable
UL 181B-M
FOR USE WITH U.L. LISTED FLEXIBLE
AIR DUCTS OR CONNECTORS
City of Los Angeles Approval RR#8427

PRECAUTIONS
For additional information contact:
Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of
children. Review MSDS for complete safety information prior to use. 900 Hensley Lane
DO NOT use where acidic or alkaline chemicals are present (ie., lab Wylie, Texas 75098
fume hood, vents, etc.)
Phone: (800) 527-7092 FAX: (972) 442-0076
For Industrial Professional Use Only. www.hardcast.com

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


601241
8
VERSA-GRIP 102

it h
Com pliant w
uiremen ts
LE ED Req

Indoor/Outdoor Water Based Duct Sealant


VERSA-GRIP 102 is a general purpose, water based duct sealant for use on all types of metal duct,
glass fiber duct board, and flex duct, as well as duct fabric and flexible tubing runouts. VERSA-GRIP
incorporates a built-in fiber reinforcement for added strength, with UV inhibitors for extended outdoor
exposure. UL 181A-M listed / UL 181B-M listed.

TECHNICAL DATA VERSA-GRIP 102 PART NUMBERS


Color �������������������������������������� White
Consistency �������������������������� Heavy textured 1 Case w/ (25) 11 oz. Cartridges.................................304152
Base �������������������������������������� Synthetic latex 1 Case w/ (4) 1-Gallon Pails........................................304153
Solvent ���������������������������������� Water
1 - 2-Gallon Pail...........................................................304155
Weight per Gallon ��������������� 11.6 lbs.
Solids Content ���������������������� 70% 1 - 5 Gallon Pail...........................................................304154
Viscosity ������������������������������� Thixotropic
Coverage (UL 181 A-M) �������� Apply 18 mil, scrim, addt. 18 mil
(UL 181 B-M) ������������������������� Approximately 214 to 320 lin. ft. per gal. APPLICATION
at 20 to 30 mil wet film thickness at 3” Temperature ��������������� 35°F to 110°F (1.7°C to 44°C)
width. Method ������������������������ Brush, putty knife, caulk gun, pump
Shore A Hardness ���������������� >20
Flexibility ������������������������������ Passes ¼ inch mandrel bend Preparation ����������������� Surface must be dry, dirt, oil, and grease
Time to Test �������������������������� 48 hours* free.
Service Temperature ������������ -20°F to 200°F Rate ���� (UL 181 A-M): Apply 18 mil, scrim and 18 mil over scrim.
Surface Burning ������������������� Flame Spread....................... 0
������������� (UL 181 B-M): Approx. 214 to 320 lin. ft. per gal. at 20 to
Smoke Developed................ 0
30 mil wet film thickness at 3” width.
(When tested in accordance with ASTM E84, UL 723)
Mildew Resistance ��������������� Mold & Mildew resistant Clean Up Wet �������������� Soap and water
VOC ��������������������������������������� 45 g/l (less water) Clean Up Dry �������������� UN-TACK™ or Solvent
Pressure Classes ����������������� SMACNA ½ , 1, 2, 3, 4, 6 and 10 inches w.g. (Use safe handling practices.)
Seal Classes ������������������������� SMACNA A, B, C
Packaging ����������������������������� 1, 2 & 5 gal. pails; 10.3 oz. cart. Painting ����������������������� Only latex or epoxy paints
Freeze/Thaw Stability ���������� Passed 5 Cycles Ductboard ������������������� Scrim required for UL 181A-M
Specification Compliance ��� Passes ASTM C-731, D-2202 USDA,
EPA & FDA Approved. LEED compliant STORAGE
*May vary according to SCAQMD Rule 1168. Temperature ��������������� 35°F to 110°F (1.7°C to 44°C)
temperature and humidity
DO NOT FREEZE
Underwriters Laboratories Inc.® Shelf Life ��������������������� One year (unopened)
LISTED
Flammability ��������������� Non-flammable
17NF
UL 181A-M
FOR USE WITH U.L. LISTED RIGID
FIBERGLASS AIR DUCTS OR CONNECTORS.
UL 181B-M
FOR USE WITH U.L. LISTED FLEXIBLE
AIR DUCTS OR CONNECTORS
City of Los Angeles Approval RR#8427

PRECAUTIONS For additional information contact:


Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of
children. Review MSDS for complete safety information prior to use. 900 Hensley Lane
DO NOT use where acidic or alkaline chemicals are present (ie., lab Wylie, Texas 75098
fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
For Industrial Professional Use Only. www.hardcast.com

601240
Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
9
DUCT-SEAL 321

t with
C omplian
e ments
LEED R equir

Indoor/Outdoor Water Based Duct Sealant


DUCT-SEAL 321 is an all purpose industrial grade duct sealant for all types of metal duct, glass fiber
duct board, and flex duct, as well as duct fabric and flexible tubing runouts. It includes UV inhibitors for
extended outdoor exposure and built-in fiber reinforcement for added strength. This non-toxic water
based product is solvent free and is suitable for residential use.

TECHNICAL DATA DUCT-SEAL 321 PART NUMBERS


Color ��������������������������������������������� Gray
Consistency �������������������������������� Smooth creamy texture 1 Case w/ (25) 11 oz. Cartridges.................................304159
Base ��������������������������������������������� Synthetic latex 1 Case w/ (4) 1-Gallon Pails........................................304156
Solvent ����������������������������������������� Water
1 - 2-Gallon Pail...........................................................304157
Weight per Gallon ����������������������� 10.6 lbs.
Solids Content ����������������������������� 65% 1 - 5-Gallon Pail...........................................................304158
Viscosity �������������������������������������� Thixotropic
Coverage (per gal) ���������������������� Up to 320 lin. ft. at 3” width
20 mil thickness APPLICATION
Shore A Hardness ����������������������� >20 Temperature ���������������������35°F. to 110°F. (1.7°C to 44°C)
Flexibility ������������������������������������� Passes ¼ inch mandrel bend
Time to Test ��������������������������������� 48 hours* Method ������������������������������Brush, putty knife, caulk gun, pump
Service Temperature ������������������� -20°F to 200°F Preparation �����������������������Surface must be dry, dirt, oil
Weather Resistance �������������������� Weather resistant and grease free.
Mildew Resistance ���������������������� Mold & Mildew resistant
Rate �����������������������������������Apply at joints and fasteners to 20
VOC (less water) ������������������������� 75 g/l (less water)
mil thick wet film
Pressure Classes ������������������������ SMACNA ½ , 1, 2, 3, 4, 6 and
10 inches w.g. Clean Up Wet ��������������������Soap and water
Seal Classes �������������������������������� SMACNA A, B, C
Clean Up Dry ��������������������UN-TACK™ or Solvent
Packaging ������������������������������������ 11 oz. cart., 1, 2 & 5 gal. pails
(Use safe handling practices.)
Freeze/Thaw Stability ����������������� Passed 5 Cycles
Specifications Compliance �������� Passes ASTM D-2202, ASTM Painting ����������������������������Only latex or epoxy paints
*May vary according to C-731. USDA, EPA and FDA
temperature and humidity Approved. LEED compliant STORAGE
SCAQMD Rule 1168. Temperature ���������������������35°F. to 110°F. (1.7°C to 44°C)
DO NOT FREEZE
CAULKING AND SEALANTS
94PF Shelf Life ��������������������������One year (unopened)
SURFACE BURNING CHARACTERISTICS
FLAME SPREAD....................................... 0 Flammability ���������������������Non-flammable
SMOKE DEVELOPED.............................. 0
*Applied to inorganic reinforced Cement Board *Tested as applied in
one 3 in. (76.2 mm) wide strip, on center covering 16.7 percent of the
exposed test sample area) at a coverage of 80 sq. ft/ gal (2 sq. M/L).
Flash point of finished sealant, closed cup : No flash to boiling.

17NF
UL 181B-M
Mastic closure systems for use with flexible
duct systems or connectors.

City of Los Angeles Approval RR #8069

PRECAUTIONS For additional information contact:


Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Apply when
temperatures will not fall below freezing for at least 36-48 hours,
depending on temperature and humidity. Do not apply this product
where temperatures will exceed 200°F. Keep out of the reach of
900 Hensley Lane
children. Review MSDS for complete safety information prior to use.
DO NOT use where acidic or alkaline chemicals are present (ie., lab Wylie, Texas 75098
fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com
For Industrial Professional Use Only.
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation 601242
10
CCWI-181
with Indoor/Outdoor
Co mpliant
em ents Water Based Duct Sealant
LEED R equir

A versatile, all purpose duct sealant for use on all types of metal duct, glass fiber duct board,
and flex duct, as well as duct fabric and flexible tubing runouts. CCWI 181 incorporates a built-
in polyester reinforcement for exceptional strength, with UV inhibitors for outdoor use. UL
181A-M listed / UL 181B-M listed.
TECHNICAL DATA CCWI-181 PART NUMBERS
Color �������������������������������������White & Gray
Consistency �������������������������Heavy textured 1 Case w/ (25) 11 oz. Cartridges (White)....................304142
Base ��������������������������������������Synthetic latex 1 Case w/ (25) 11 oz. Cartridges (Gray)......................304146
Solvent ����������������������������������Water 1 Case w/ (4) 1-Gallon Pails (White)...........................304144
Weight per Gallon ���������������11.6 lbs. 1 Case w/ (4) 1-Gallon Pails (Gray)............................304148
Solids Content ���������������������70%
1 - 2-Gallon Pail (White)..............................................304143
Viscosity �������������������������������Thixotropic
1 - 2-Gallon Pail (Gray)...............................................304147
Coverage (UL 181 A-M) �������Apply 18 mil, scrim, addt. 18 mil
(UL 181 B-M) �������Approximately 214 to 320 lin. ft. per gal. at 1 - 5-Gallon Pail (White)..............................................304145
20 to 30 mil wet film thickness at 3” width. 1 - 5-Gallon Pail (Gray)...............................................304149
Shore A Hardness ����������������>20
Flexibility ������������������������������Passes ¼ inch mandrel bend APPLICATION
Time to Test ��������������������������48 hours* Temperature �����������������35°F. to 110°F. (1.7°C to 44°C)
Service Temperature �����������-20°F to 200°F Method �������� �����������������Brush, putty knife, caulk gun, pump
Mildew Resistance ���������������Mold & Mildew resistant Preparation � �����������������Surface must be dry, dirt, oil, and
VOC ���������������������������������������45 g/l (less water)
grease free.
Surface Burning �������������������Flame Spread...............................0
Rate (UL 181 A-M): �������Apply 18 mil, scrim and 18 mil over scrim.
Smoke Developed........................0
(UL 181 B-M): ������Approx. 214 to 320 lin. ft. per gal. at 20
(When tested in accordance with ASTM E84, UL 723)
to 30 mil wet film thickness at 3” width.
Pressure Classes �����������������SMACNA ½ , 1, 2, 3, 4, 6 and 10 inches w.g.
Seal Classes �������������������������SMACNA A, B, C Clean Up Wet ����������������Soap and water
Packaging �����������������������������11 oz. cart.; 1, 2 & 5 gal. pails Clean Up Dry ����������������UN-TACK™ or Solvent
(Use safe handling practices.)
Freeze/Thaw Stability ����������Passed 5 Cycles
Specification Compliance ���Passes ASTM C-731, D-2202 USDA, Painting ������� �����������������Only latex or epoxy paints
EPA & FDA Approved. LEED compliant Ductboard...................... Scrim required for UL 181A-M
*May vary according to
temperature and humidity SCAQMD Rule 1168. STORAGE
Temperature ������������������35°F. to 110°F. (1.7°C to 44°C)
Underwriters Laboratories Inc.® DO NOT FREEZE
LISTED
17NF Shelf Life ����� �����������������One year (unopened)
UL 181A-M Flammability �����������������Non-flammable
FOR USE WITH U.L. LISTED RIGID
FIBERGLASS AIR DUCTS OR CONNECTORS.
UL 181B-M
FOR USE WITH U.L. LISTED FLEXIBLE
AIR DUCTS OR CONNECTORS

City of Los Angeles Approval RR#8427

For additional information contact:


PRECAUTIONS
Surface must be clean and free of moisture, contamination and foreign
matter. Do not allow this product to freeze. Do not apply when rain
or freezing temperatures will occur within 36 hours. Do not apply
this product where temperatures will exceed 200°F. Keep out of the
reach of children. Review MSDS for complete safety information 900 Hensley Lane
prior to use. DO NOT use where acidic or alkaline chemicals are Wylie, Texas 75098
present (ie., lab fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
For Industrial Professional Use Only. www.hardcast.com

Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
11
SURE-GRIP 404

t with
Solvent Based Duct Sealant
C omplian
e ments
LEED Requir

SURE-GRIP 404 is a fiber-free, solvent based, synthetic rubber duct sealant. It’s exceptional strength,
fast drying time, and unmatched flexibility make it ideal for those applications requiring a solvent based
sealant. SURE-GRIP’s low viscosity, no-drip, no-string formulation allows fast application for labor
savings and extended coverage for lower installed cost.

TECHNICAL DATA SURE-GRIP 404 PART NUMBERS


Color ����������������������������������������������Gray
Consistency ���������������������������������Heavy Brush On 1 Case w/ (25) 11 oz. Cartridges.................................302014
Base ����������������������������������������������Synthetic Rubber Resin 1 Case w/ (4) 1-Gallon Pails........................................302009
Solvent ������������������������������������������Toluene and Heptane
1 - 5-Gallon Pail...........................................................302020
Weight per Gallon ������������������������8.8 lbs.
Solids Content ������������������������������65%
Viscosity ���������������������������������������150K - 200K cps
APPLICATION
Coverage (per gal.) ���������������������Up to 320 lin. ft. at 3” width,
20 mil thickness Temperature ������������������������ 35°F. to 100°F. (1.7°C. to 38°C.)
Shore A Hardness ������������������������>60
Method ��������������������������������� Brush, putty knife,caulk gun,
Flexibility ��������������������������������������Excellent trowel and spray
Time to Test ����������������������������������24 hours
Service Temperature ��������������������-20°F to 200°F Preparation �������������������������� Surface must be dry, dirt, oil and
Water Resistance �������������������������Excellent grease free.
Mildew Resistance �����������������������Mold & Mildew resistant
VOC �����������������������������������������������360 g/l Rate �������������������������������������� Apply at joints and fasteners to
Pressure Classes �������������������������SMACNA ½, 1, 2, 3, 4, 6 and 20 mil thick wet film
10 inches w.g. Clean Up ����������������������������� UN-TACK™ or Solvent
Seal Classes ���������������������������������SMACNA A, B, C (Use safe handling practices.)
Packaging �������������������������������������11 oz. cart., 1 & 5 gal. pails.
Freeze/Thaw Stability ������������������Passed 5 Cycles Painting �������������������������������� Allow 72 hours
Specifications Compliance ���������� Passes ASTM D-2202,
LEED compliant SCAQMD STORAGE
Rule 1168.
Temperature ������������������������ Below 90°F. (32°C.)
UNDERWRITERS LABORATORIES, INC.®
CLASSIFIED
Shelf Life ������������������������������ One year (unopened)
ADHESIVE
Surface Burning Characteristics Flammability ������������������������ Flammable. Store according to
294U local code.
*Applied to inorganic reinforced cement board

FLAME SPREAD...................................10
SMOKE DEVELOPED............................5
*Tested as applied in two 1/4 inch wide strips 8 inches on center at a coverage of 320
lin.ft./gal. Flash point of finished adhesive, closed cup: less than minus 14OC.

17NF
UL 181B-M
Mastic closure systems for use with flexible
duct systems or connectors.

City of Los Angeles Approval RR#8069


For additional information contact:
PRECAUTIONS
FLAMMABLE liquid and vapor. Keep away from open flame. May cause
flash fire. Contains heptane and toluene solvents. Harmful if swallowed or
inhaled. May cause eye irritation. Do not apply this product in areas where
intense overexposure is anticipated, or where temperatures will exceed 200°F
900 Hensley Lane
. Keep out of the reach of children. Review Material Safety Data Sheet
for complete safety information prior to use. DO NOT use where acidic or Wylie, Texas 75098
alkaline chemicals are present (ie., lab fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com
For Industrial Professional Use Only.
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
601238
12
COLD-SEAL

t with Permanently Tacky


C omplian
e ments Pumpable Seam Sealant
LEED Requir

A cold applied, non-hardening, fire retardent seam sealant for use in rectangular, longitudinal, Pittsburgh™,
snap-lock or similar metal duct seams. COLD-SEAL will not string, saving equipment cleanup labor. In
addition, COLD-SEAL resists drying in equipment hoses, avoiding costly replacement.

TECHNICAL DATA
COLD-SEAL PART NUMBERS
Color �������������������������������������������� Gray
Consistency ������������������������������� Heavy Viscous 1 - 5-Gallon Pail...........................................................302022
Base �������������������������������������������� Synthetic Rubber 1 - 55-Gallon Drum......................................................302023
Solvent ���������������������������������������� Mineral Spirits
Weight per Gallon ���������������������� 9.7 lbs.
Solids Content ���������������������������� 86 %
APPLICATION
Viscosity ������������������������������������� Thixotropic
Coverage ������������������������������������ 1550 linear ft./gal., 1/8 in. bead Temperature �����������������������35°F. to 90°F. (1.7°C. to 32°C.)
Flexibility ������������������������������������ Excellent Method �������������������������������Graco, Binks or Lockformer;
Time to Test �������������������������������� Immediately 1
/8 in. orifice
Service Temperature ������������������ -30°F. to 200°F. Preparation ������������������������Surface must be dry, dirt, oil,
Surface Burning* ������������������������ Flame Spread....................0 and grease free.
Smoke developed..............5 Rate ������������������������������������Apply 1/8 in. bead to seams prior
Water Resistance ����������������������� Excellent to closing
Mildew Resistance ��������������������� Excellent
Clean Up ����������������������������UN-TACK™ or Solvent
VOC ��������������������������������������������� 198 g/l (Use safe handling practices.)
Pressure Classes ����������������������� SMACNA ½ , 1, 2, 3, 4, 6 and 10
inches w.g. STORAGE
Seal Classes ������������������������������� SMACNA A, B, C Temperature �����������������������35°F. to 90°F. (1.7°C. to 32°C.)
Packaging ����������������������������������� 5 gal. and 55 gal. Shelf Life ����������������������������One year (unopened)
Freeze/Thaw Stability ���������������� Excellent
Flammability ����������������������Combustible. Flash Point 150°F
Specification Compliance ����������LEED compliant SCAQMD
(Tcc). Store according to local
Rule 1168. codes.
*When tested in accordance with ASTM E84

PRECAUTIONS

COMBUSTIBLE. Harmful if swallowed or inhaled May cause eye


irritation. Keep out of the reach of children. Review Material Safety
Data Sheet for complete safety information prior to use.
For additional information contact:

For Industrial Professional Use Only.

900 Hensley Lane


Wylie, Texas 75098
Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

601251
Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
13
AB-151 Scrim
HVAC/Construction Scrim

AB-15-Scrim is an all purpose self-adhering fiberglass ductwork scrim primarily used for temporary
fixation of ductwork prior to sealant application. For use with UL 181 Listed applications.

TECHNICAL DATA
AB-151 Scrim PART NUMBER
Average net weight..............................1.6 (oz./yd²)
1 Case w/ (10) 3” x 150’ Rolls...................................310553
Cross directional strength..................104.8 (lbs./in.)

Treatment % on fabric.........................22.5%

Thread Count (per inch of width) APPLICATION


Warp threads ..............................9
Filling threads .............................9 Temperature ������������� 35°F. to 110°F. (1.7°C. to 44°C.)

Thicknes ...............................................007 in. Method ���������������������� Cut desired length, peel off release liner,
apply. Overlap at ends. Rub down with
Packaging............................................3” X 150’; 18 rolls per case heavy pressure to assure complete
contact.

Preparation ��������������� Surface must be clean and dry, oil and


grease free.

Clean Up ������������������� UN-TACK™ or Solvent


(Use safe handling practices.)

Painting ��������������������� Use paint appropriate for aluminum.

STORAGE
Temperature ������������� 35°F. to 110°F. (1.7°C to 44°C)

Shelf Life ������������������� 24 months

Flammability ������������� Non-flammable

PRECAUTIONS
For additional information contact:
Surface must be clean and free of moisture, contamination and
foreign matter. Do not allow this product to freeze. Do not apply
this when rain or freezing temperatures will occur within 36 hours.
Do not apply this product where temperatures will exceed 200°F.
Keep out of the reach of children. Review MSDS for complete
900 Hensley Lane
safety information prior to use. DO NOT use where acidic or alkaline
Wylie, Texas 75098
chemicals are present (ie., lab fume hood, vents, etc.) Phone: (800) 527-7092 FAX: (972) 442-0076
For Industrial Professional Use Only. www.hardcast.com

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


600782
14
ALL-PURPOSE 1602

t with
All Purpose Rolled Sealant
C omplian
em ents
LEED R equir

ALL-PURPOSE is a pressure sensitive, 30-year cycle, duct joint and general purpose rolled sealant.
ALL-PURPOSE provides an instant aggressive grip to most surfaces including sheet metal, duct board,
and flex duct for indoor applications. The GRAY MATTER™ butyl adhesive/sealant is a 100% solids
sealant, which stays flexible and does not release from the substrate.

TECHNICAL DATA
ALL-PURPOSE 1602 PART NUMBERS
Appearance................................... White fabric substrate with gray
adhesive/sealant 1 Case w/ (24) 2” x 50’ Rolls.....................................304086
Backing.......................................... DuPont Sontara® polyester 1 Case w/ (16) 3” x 50’ Rolls.....................................304087
1 Case w/ (12) 4” x 50’ Rolls.....................................304088
Thickness...................................... 25 mils
1 Case w/ (8) 6” x 50’ Rolls.......................................304089
Sealant Material............................. Modified Butyl
1 Case w/ (4) 12” x 50’ Rolls.....................................304085
Peel Strength................................. 17 lbs. per linear inch
Tensile Strength............................ 790 psi avg.
Elongation...................................... 560% avg. APPLICATION
Temperature............... 35°F. to 110°F. (1.7°C. to 44°C.)
Flexibility....................................... Excellent, no cracking
Method........................ Cut desired length, peel
Bonding Time................................ Immediate aggressive grip, full
off release liner, and apply.
bond 24 hours (Removal or repositioning may
Time to test.................................... Immediate damage AP-1602 and surface.)
Overlap at ends. Rub down with
Service Temperature..................... -20°F. to 200°F.
heavy pressure to assure complete
Surface Burning............................ Flame Spread:................. 15 contact.
Smoke Developed:.......... 15 Preparation................. Surface must be clean and dry, oil
(When tested in accordance with ASTM E-84) and grease free.
Water Resistance.......................... Excellent. Surface must be dry Clean Up..................... UN-TACK™ or Solvent
before application (Use safe handling practices.)

Mildew Resistance........................ Mold and mildew resistant. Painting....................... Use epoxy or water based paint
or coating. Use weatherized paint
VOC................................................ 0 g/l when applied on exterior surfaces.
Pressure Classes.......................... SMACNA ½ , 1, 2, 3, 4 and 6 in. w.g.
STORAGE
Seal Classes.................................. SMACNA A, B, C
Temperature............... 35°F. to 110°F. (1.7°C. to 44°C.)
Packaging...................................... 50 ft. rolls in 2, 3, 4, 6 & 12 inch
widths. 200 sq. ft. per case. Shelf Life..................... 24 months
Flammability............... Non-flammable
Specifications Compliance.......... LEED compliant SCAQMD
Rule 1168

PRECAUTIONS For additional information contact:


Surfaces must be clean and free of moisture and contamination.
Do not apply this product in weather exposed area without suitable
paint or coating. Do not apply this product where temperatures will
exceed 200° F. Keep out of the reach of children. Review MSDS for
safety information prior to use. DO NOT use where acidic or alkaline 900 Hensley Lane
chemicals are present (ie., lab fume hood, vents, etc.) Wylie, Texas 75098
Phone: (800) 527-7092 FAX: (972) 442-0076
For Industrial Professional Use Only. www.hardcast.com

601246
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
15
ALUMA-GRIP 701

t ith Premium Indoor/Outdoor


C omplia n w
LEED Requir
e ments Rolled Sealant
ALUMA-GRIP is a HEAVY DUTY pressure sensitive, 40-year cycle, duct joint rolled sealant. ALUMA-
GRIP provides an aggressive water resistant grip to most surfaces including sheet metal, duct board, flex
duct, PVC coated duct, and duct wrap vapor barriers. ALUMA-GRIP is suitable for subgrade application
on PVC coated duct.

TECHNICAL DATA ALUMA-GRIP 701 PART NUMBERS


Appearance............................. Mill finish aluminum substrate with 1 Case w/ (24) 2” x 50’ Rolls.......................................304078
gray adhesive/sealant
1 Case w/ (16) 3” x 50’ Rolls.......................................304079
Backing.................................... Aluminum
1 Case w/ (12) 4” x 50’ Rolls.......................................304080
Thickness................................ 30 mils 1 Case w/ (8) 6” x 50’ Rolls.........................................304081
Sealant Material...................... Modified Butyl 1 Case w/ (4) 9” x 50’ Rolls.........................................304082
Peel Strength........................... 17 lbs. per linear inch 1 Case w/ (4) 12” x 50’ Rolls.......................................304077
Tensile Strength...................... 720 psi avg.
Elongation .............................. 560% avg.
APPLICATION
Flexibility................................. Excellent, no cracking
Bonding Time.......................... Instant high tack, full bond 24 hours Temperature..................35°F. to 110°F. (1.7°C. to 44°C.)

Time to Test............................. Immediate Method...........................Cut desired length, peel off


release liner, and apply.Removal
Service Temperature.............. -20°F. to 200°F. or repositioning may damage
Surface Burning...................... Flame Spread: .................25 AFT-701 and surface. Overlap
Smoke Developed:...........50 at ends. Rub down with heavy
(When tested in accordance with ASTM E-84) pressure to assure complete
contact.
Weather Resistance................ Passes 2000 hours QUV
(When tested in accordance with ASTM G-53) Preparation....................Surface must be clean and dry, oil
and grease free.
Mildew Resistance.................. Mold and mildew resistant
VOC.......................................... 0 g/l Clean Up .......................UN-TACK™ or Solvent
(Use safe handling practices.)
Pressure Classes.................... SMACNA ½, 1, 2, 3, 4, 6 and 10
inches w.g. Painting..........................Use paint appropriate
for aluminum.
Seal Classes............................ SMACNA A, B, C
STORAGE
Packaging................................ 50 ft. rolls in 2, 3, 4, 6, 9, 12 inch
widths. 200 sq. ft. per case Temperature..................35°F. to 110°F. (1.7°C. to 44°C.)
(150 sq. ft. for 9 inch)
Specifications Compliance.... LEED compliant SCAQMD Shelf Life........................24 months
Rule 1168 Flammability..................Non-flammable

PRECAUTIONS
For additional information contact:
Surfaces must be clean and free of moisture and contamination. Do
not apply this product in areas where temperatures will exceed 200°F.
Keep out of the reach of children. Review MSDS for safety informa-
tion prior to use. DO NOT use where acidic or alkaline chemicals are
present (ie., lab fume hood, vents, etc.)
900 Hensley Lane
For Industrial Professional Use Only. Wylie, Texas 75098
Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation 601244


16
FOIL-GRIP 1402

t with Indoor/Outdoor Rolled Sealant


C omplian
e ments
LEED Requir

FOIL-GRIP 1402 is a pressure sensitive, 40-year cycle, duct joint and general purpose rolled sealant.
It provides an instant water resistant grip to most surfaces including sheet metal, duct board, flex duct,
PVC coated duct, and duct wrap vapor barriers. FOIL-GRIP 1402 is suitable for subgrade application
on PVC coated duct.

TECHNICAL DATA FOIL-GRIP 1402 PART NUMBERS


Appearance ���������������������������� Mill finish aluminum substrate with
1 Case w/ (24) 2” x 100’ Rolls (Non-Printed)...............304093
gray adhesive/sealant
1 Case w/ (16) 3” x 100’ Rolls (Non-Printed)...............304094
Backing ����������������������������������� Aluminum
Thickness ������������������������������� 17 mils 1 Case w/ (12) 4” x 100’ Rolls (Non-Printed)...............304095
Sealant Material ��������������������� Modified Butyl 1 Case w/ (8) 6” x 100’ Rolls (Non-Printed).................304096
Peel Strength �������������������������� 16 lbs. per linear inch 1 Roll 36” x 100’ (Non-Printed)....................................304083
Tensile Strength ��������������������� 955 psi avg. 1 Case w/ (24) 2” x 100’ Rolls (Printed).......................304099
Elongation ������������������������������ 560% avg.
1 Case w/ (16) 3” x 100’ Rolls (Printed).......................304100
Flexibility �������������������������������� Excellent, no cracking
Bonding Time ������������������������� Instant high tack, full bond 24 hours
Time to Test ���������������������������� Immediate APPLICATION
Service Temperature �������������� -20°F. to 220°F. Temperature �������������� 35°F. to 110°F. (1.7°C. to 44°C.)
Weather Resistance Passes 2000 hours QUV Method ����������������������� Cut desired length, peel off release
(When tested in accordance with ASTM G-53)
liner, apply. Removal or repositioning
Mildew Resistance ����������������� Mold and mildew resistant may damage AFG-1402 and surface.
VOC ����������������������������������������� 0 g/l Overlap at ends. Rub down with heavy
Pressure Classes ������������������� SMACNA ½, 1, 2, 3, 4, & 6 in. w.g. pressure to assure complete contact.
Seal Classes ��������������������������� SMACNA A, B, C Preparation ���������������� Surface must be clean, dry, oil and
Packaging ������������������������������� 100 ft. rolls in 2, 3, 4 & 6 inch widths grease free
400 sq. ft. per case Clean Up �������������������� UN-TACK™ or Solvent
Specifications Compliance ��� LEED compliant SCAQMD (Use safe handling practices.)
Rule 1168
Painting ���������������������� Use paint appropriate for aluminum.

UNDERWRITERS LABORATORIES INC.® STORAGE


CLASSIFIED
GENERAL USE TAPES Temperature �������������� 35°F. to 110°F. (1.7°C. to 44°C.)
SURFACE BURNING CHARACTERISTICS
773S
Shelf Life �������������������� 24 months
*Applied to inorganic reinforced Cement Board
Flammability �������������� Non-flammable
FLAME SPREAD............................................... 20
SMOKE DEVELOPED....................................... 40

*Tested in two 3 inch (76 mm) wide longitudinal strips 8 inches (203 mm)
on center. (Tape coverage: 30% of the exposed test sample area.)

City of Los Angeles Approval RR #8069

For additional information contact:


PRECAUTIONS
Surfaces must be clean and free of moisture and contamination. Do
not apply this product in areas where temperatures will exceed 200°F.
Keep out of the reach of children. Review MSDS for safety informa-
tion prior to use. DO NOT use where acidic or alkaline chemicals are
present (ie., lab fume hood, vents, etc.) 900 Hensley Lane
Wylie, Texas 75098
For Industrial Professional Use Only.
Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

601245
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
17
FOIL-GRIP 1403-181BFX

C omplian
t with Indoor/Outdoor Rolled Sealant
e ments
LEED Requir

FOIL-GRIP 1403-181BFX is a UL 181B-FX listed pressure sensitive, 40-year cycle, duct joint and general
purpose rolled sealant. FOIL-GRIP 1403-181BFX provides an instant water resistant grip to most
surfaces including sheet metal, duct board, flex duct, PVC coated duct, and duct wrap vapor barriers.
FOIL-GRIP 1403-181BFX is suitable for subgrade application on PVC coated duct.

TECHNICAL DATA
FOIL-GRIP 1403-181BFX
Appearance............................. Mill finish aluminum substrate with
butyl adhesive/sealant
PART NUMBERS
Backing.................................... Aluminum 1 Case w/ (24) 2” x 100’ Rolls.....................................309781
Thickness................................ 17 mils 1 Case w/ (16) 3” x 100’ Rolls.....................................309780
Sealant Material........................ Modified Butyl
Peel Strength........................... 7 lbs. per linear inch
Tensile Strength...................... 20 pli/1400 psi avg. APPLICATION
Flexibility................................. Excellent, no cracking Temperature............... 35°F. to 110°F. (1.7°C. to 44°C.)
Bonding Time.......................... Instant high tack, full bond 24 hours
Method........................ Cut desired length, peel off release liner,
Time to Test............................. Immediate apply. Removal or repositioning may
Service Temperature............... -20°F. to 200°F. damage FOIL-GRIP 1403-181BFX
Weather Resistance................ Passes 2000 hours QUV and surface. Overlap at ends. Rub
(When tested in accordance with ASTM G-53) down with adequite pressure to assure
Mildew Resistance.................. Mold and mildew resistant complete contact.
VOC.......................................... 0 g/l Preparation................. Surface must be clean and dry, oil
Pressure Classes.................... SMACNA ½, 1, 2, 3, 4, & 6 in. w.g. and grease free.
Seal Classes............................ SMACNA A, B, C Clean Up..................... UN-TACK™ or Solvent
Packaging................................ 100 ft. rolls in 2 & 3 inch widths; (Use safe handling practices.)
400 sq. ft. per case. Painting....................... Use paint appropriate for aluminum.
Specifications Compliance.... LEED compliant SCAQMD
Rule 1168 STORAGE
Temperature............... 35°F. to 110°F. (1.7°C. to 44°C.)
GENERAL USE TAPES
773S Shelf Life..................... 24 months
SURFACE BURNING CHARACTERISTICS
APPLIED to INORGANIC
Flammability............... Non-flammable
REINFORCED CEMENT BOARD+
FLAME SPREAD............................................... 0
SMOKE DEVELOPED....................................... 5
+Tested as applied in one 50.8 (2 in.) wide strip on center.
(Tape coverage: 11.1 percent of the exposed test sample area).

181B-FX
17NF
PRESSURE SENSITIVE TAPES FOR USE WITH
FLEXIBLE AIR DUCTS FOR CLASS 1 DUCT

PRECAUTIONS For additional information contact:


Surfaces must be clean and free of moisture and contamination. Do
not apply this product in areas where temperatures will exceed 200°F.
Keep out of the reach of children. Review MSDS for safety informa-
tion prior to use. DO NOT use where acidic or alkaline chemicals are
present (ie., lab fume hood, vents, etc.) 900 Hensley Lane
For Industrial Professional Use Only. Wylie, Texas 75098
Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


601397
18
WATER CUT-OFF
MASTIC
Carlisle Sure-Seal® Water Cut-Off Mastic
A cold applied, non-hardening, fire retardant roofing sealant for use on roof penetrations and roof
curbs. Water Cut-Off Mastic bonds quickly and is UV tolerant.
• ROOF PENETRATIONS • ROOF CURB SEALANT • UV TOLERANT

TECHNICAL DATA WATER CUT-OFF MASTIC PART NUMBER


Color.......................................... Gray 1 Case w/ (10) 10.3 oz. Cartridges..............................302196
Consistency............................. Heavy Viscous
Base.......................................... Synthetic Rubber
Solvent...................................... Aliphatic Petroleum Distillate
Solids Content.......................... 80-90%
Viscosity, Brookfield................ 800,000 - 1,800,000 cps COVERAGE
Coverage.................................. 1550 linear ft./gal., 1/8 in. bead 10’ (3 m) per tube or 128’ (39 m) per gallon using a 7/16” (11
mm) bead.
Flexibility.................................. Excellent
APPLICATION
Time to Test.............................. Immediately 1. A ll surfaces to be sealed with Water Cut-Off Mastic
Service Temperature................ -40°F to 200°F (-40°C to 93°C) must be a masonry, metal or glass substrate and free of
moisture, oil, dirt and other foreign materials.
Net Weight Per Gallon............. 10.00 - 11.20 lbs. (4.5 - 5.0 Kg) 2. Apply a 7/16” (11 mm) bead of Water Cut-Off Mastic
Specific Gravity........................ 1.20 - 1.32 between the substrate and the edge of the membrane.
3. Apply appropriate termination material and secure to
Surface Burning....................... Flame Spread........................0
provide constant compression for the Water Cut-Off
. Smoke developed..................5 Mastic.
(When tested in accordance with
ASTM E84) Application Temperature . ....... 35°F to 90°F
Clean Up ................................. UN-TACK, Mineral spirits or
Water Resistance..................... Excellent Solvent. (Use safe
Mildew Resistance................... Excellent handling practices.)
VOC........................................... max. 250 gpl STORAGE
Pressure Classes..................... SMACNA ½ , 1, 2, 3, 4, 6 Temperature............................. 35°F to 90°F
and 10 inches w.g. Shelf Life.................................. One year (unopened)
Seal Classes............................. SMACNA A, B, C Flammability............................ Flammable.
Flash Point 40°F (4°C) (TCC).
Packaging................................. 11 oz. Cartridge
Store per local codes.
Freeze/Thaw Stability.............. Excellent

PRECAUTIONS
For additional information contact:

FLAMMABLE. Harmful if swallowed or inhaled May cause eye


irritation. Keep out of the reach of children. Review Material Safety
Data Sheet for complete safety information prior to use.
900 Hensley Lane
Wylie, Texas 75098
For Industrial Professional Use Only.
Phone: (800) 527-7092 FAX: (972) 442-0076
www.hardcast.com

601252
Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation
19
SILIMAX
®

HI-TEMPERATURE SILICONE SEALANT

SILIMAX HI-TEMP PART NUMBER


1 Case w/ (12) 10.1 oz. Cartridges..............................309983

• Color: Red

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


20
SILIMAX
®

MULTI-PURPOSE SILICONE SEALANT

pg. 1 of 2

Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
21
SILIMAX
®

MULTI-PURPOSE SILICONE SEALANT

pg. 2 of 2

SILIMAX MULTI-PURPOSE PART NUMBERS


Aluminum - 1 Case w/ (12) 10.1 oz. Cartridges..........309980
White - 1 Case w/ (12) 10.1 oz. Cartridges.................309981
Clear - 1 Case w/ (12) 10.1 oz. Cartridges..................309982

Printed in U.S.A. 09/08 supercedes 08/07 ©2008 Carlisle Corporation


22
METALBOND
TYTAN HIGH TEMPERATURE
100% Silicone Sealant
MOISTURE CURING SEALANT

Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
23
TREMstop IA
Intumescent Acrylic Firestopping Sealant

PRO D UCT D E S CR I P T I O N: A D VA NTA G ES :


TREMstop IA is a single component, water-based, intumescent acrylic firestop • Single component, water-based,
sealant that will expand to fill any void left when combustible materials burn away intumescent acrylic
during a fire. TREMstop IA is a unique, firestopping sealant that has been tested at • Expands to fill voids left when
independent laboratories to treat 95 percent of the applications commonly combustible materials burn away
encountered on a project. TREMstop IA has exceptional sealant qualities, including during a fire
superb unprimed adhesion, easy gunning, antifungal properties and the ability to • Approved for 95% of the
be painted once fully cured. applications encountered on a
project
Part # Product Color
• Easy gunning
304318 Tremstop IA 10oz. Cartridge 30/case Red
• Antifungal properties
304319 Tremstop IA 20oz. Cartridge 15/case Red
• Excellent flexibility
304339 Tremstop IA 5 gallon pail Red
• Paintable once fully cured
• Listed up to a 4 hour fire rating

BA SIC USE S : P HY S I CAL PROPERT IES : PA CK A G ING :


Penetrations Color: Rust red 10.1 fl. oz. (300 ml, 18 in3) cartridge
pH: 7.0 – 10.0 30/case
• Steel, copper and EMT pipe
Shore “A” Hardness: 15 – 20 20 fl. oz. (600 ml, 36 in3) sausage
• Plastic pipe (vented and closed) (ASTM C-661)
15/case
• Romex cables, jacketed cables and VOC (grams/liter): 16
28.7 fl. oz. (850 ml, 51 in3) cartridge
bundles Application
Temperature 40ºF – 110ºF 12/case
• Duct work
(Min./Max.): (5ºC – 43ºC) 5 gal. (19 L, 1155 in3) pail
• PVC and ccPVC pipe Flame Spread: 0
• ABS and ccABS pipe (ASTM E-84)
• CPVC pipe Smoke Develop: 0
(ASTM E-84)
• Fiberglass insulated pipe
Cure Time: 3 – 5 days
• AB/PVC and cellular glass pipe (ASTM C-679)
insulation Skin Over Time: Overnight
• Mixed penetrations Movement Capability: ± 3%
(UL 2079; class II, III)
Building Assemblies STC Information:
• Concrete wall or floor (ASTM E-90)
• Gypsum wallboard Evaluated to restore STC ratings of
• Wood floor/ceiling construction assemblies with STC
FGG/BM® System Compatible indicates
ratings up to 55. this product has been tested and is
• Stairway conditions monitored on an on going basis to assure

• Joints Shelf Life: 1 year chemical compatibility with FlowGuard


Gold®, BlazeMaster®, and Corzan® pipe
Freeze Sensitive: Yes and fittings.
• Hollowcore concrete FGG/BM®, FlowGuard Gold® and Corzan®
Accepts Paint: Yes are registered trademarks of The Lubrizol
Corporation.

TREMstop IA

Printed in U.S.A.
09/08 supercedes 08/07 ©2008 Carlisle Corporation
25

Вам также может понравиться