Академический Документы
Профессиональный Документы
Культура Документы
Install the controller at an angle within 30° from horizontal ■ Communication protocol • Power supply: Rated voltage of 100 to 240 V AC (10%), 50/60 Hz
Front panel
User’s Model UT350L with the front panel facing upward. Do not install it facing
downward. The position of right and left sides should be hori-
of controller Must not
Purpose Name and Manufacturer
Power supply, grounding, relay contact outputs 600 V PVC insulated wires, JIS C 3307, 0.9 to 2.0 mm2
• Personal computer link: Used for communication with a
personal computer, or UT link module of the FA-M3
•
•
Power consumption: Max. 20 VA (8.0 W max.)
Internal fuse rating: 250V AC, 1.6A time-lug fuse
7 mm or less
contact input terminals
7 mm or less
This manual describes installation, wiring, and other tasks required to make the controller ready for operation. • Setpoint display: 4-digit, 7-segment red LED display, character • Insulation resistance: 20 M or more at 500 V DC between
or height of 9.3 mm power terminals and grounding terminal
Contents • Status indicating lamps: LEDs • Grounding: Class D grounding (grounding resistance of 100
Safety and EMC Standards or less)
1. Safety Precautions
2. Model and Suffix Codes
• Safety: Complies with IEC/EN61010-1 (CE), approved by Signal Isolations
● Terminal Covers (Optional parts) C22.2 No.61010-1, approved by UL508.
91.8
112
• PV input terminals: Isolated from other input/output terminals.
96
3. How to Install Certified for FM-3810 and FM-3545. Not isolated from the internal circuit.
4. How to Connect Wires Target Model Part Number Sales Unit Installation category : CAT. II Pollution degree : 2 (IEC/ • 4-20 mA analog output terminals (for retransmission): Isolated
5. Hardware Specifications For UT350L T9115YD 1 EN61010-1, C22.2 No.61010-1) from other input/output terminals and internal circuit.
6. Terminal Wiring Diagrams Measurement category : I (CAT. I : IEC/EN61010-1) • Relay contact control output terminals: Isolated between contact
Rated measurement input voltage : 10V DC max.(across output terminals and from other input/output terminals and
terminals), 300V AC max.(across ground) internal circuit.
Small bracket 1. Before attaching the terminal cover, bend the side with Fold the cover in the direction Rated transient overvoltage : 1500V (Note)
Introduction of the arrow. • Contact input terminals: Not isolated between contact input
1 to 10 mm (Panel thickness)
the groove inward as shown in Fig. A. Be careful not to Note : It is a value on the safety standard which is assumed terminals and from communication terminals. Isolated from
Figure A
Thank you for purchasing the UT350L limit controller. bend it backwards. This not only marks it harder to by IEC/EN61010-1 in Measurement category I, and is not other input/output terminals and internal circuit.
The controller is shipped from the factory with 3 hardcopy user’s manuals (A2 size). The 3 user’s manuals in hardcopy General installation Side-by-side close installation attach the cover but will also weaken its hold. the value which guarantees an apparatus performance. • Relay contact alarm output terminals: Not isolated between
format describe the operating procedures required for basic use. It is recommended that you refer to these user’s manuals to +0.8 relay contact alarm outputs. Isolated from other input/
understand [1] installation, [2] initial settings, [3] operating procedures, and [4] limit control function of the controller.
117 min. [(N-1)96+92] 0
2. Fit the holes on the top and bottom (UT350L) of the
Fit the cover hold CAUTION output terminals and internal circuit.
over the protrusion
terminal cover the projections on the brackets (Fig. B) on the mounting bracket. • RS-485 communication terminals: Not isolated from contact
and lock in place. The figure right shows the attachment This equipment has Measurement category I, there- input terminals. Isolated from other input/output terminals
■ How to Use the Manuals fore do not use the equipment for measurements and internal circuit.
+0.8
of a terminal cover to UT350L.
0
within Measurement categories II, III and IV. • Power terminals: Isolated from other input/output terminals and
92
Purpose Manual Title Description Media internal circuit.
• Grounding terminals: Isolated from other input/output terminals
Setup Describes the tasks (installation, wiring, and others) required A2-size paper, and internal circuit.
Installation (53) 145 min. Measurement category Description Remarks
to make the controller ready for operations. front
"N" stands for the number of controllers to be CAT.1 For measurements performed
Basic operation Describes examples of setting PV input types, limit control type A2-size paper, Figure B 1
on circuits not directly Environmental Conditions
selection, and alarm types. front
installed.
However, the measured value applies if N 5.
5. Hardware Specifications connected to MAINS.
• Normal operating conditions:
Initial Settings
Making settings described herein allows you to carry out basic
+0.8
92 0 Retransmission Output 2 CAT.2 For measurements performed
on circuits directly connected
Appliances, portable
equipments, etc. Ambient temperature: 0 to 50C (40C or less for side-by-side
control. PV Input Signals Either PV, or target setpoint is output. to the low voltage installation.
close installation)
3 CAT.3 For measurements performed Distribution board,
Operating • Number of inputs: 1 (terminals 11 - 12 - 13 ) • Number of outputs: 1 (terminals 16 - 17 ) in the building installation. The operating ambient temperature range is between 0C.
Describes key operation sequences. A2-size paper, circuit breaker, etc.
procedures, For operation control through external contact inputs, 92
+0.8
(25) • Input type: Universal input system. The input type can be • Output signal: 4-20 mA DC 4 CAT.4 For measurements performed Overhead wire, cable Temperature change rate: 10C/h or less
Operations back 0 at the source of the low-voltage systems, etc.
troubleshooting, see Installation User’s Manual. selected with the software. • Load resistance: 600 or less installation. Ambient humidity: 20 to 90% RH (no condensation allowed)
and maintenance • Sampling period: 250 ms • Output accuracy: 0.3% of span under standard operating Magnetic field: 400 A/m or less
• Burnout detection: Functions at TC, RTD, standard signal conditions (23 2C, 55 10% RH, power frequency of Continuous vibration at 5 to 14 Hz: Full amplitude of 1.2 mm or
Brief operation, Contains the parameter map used as a guideline for setting
setpoint recording, Parameters and parameters and lists of parameters for recording user settings.
A2-size paper,
back and front
■ How to Install (0.4 to 2 V or 1 to 5 V) 50/60 Hz) Internal Wiring
2
less
Upscale, downscale, and off can be specified. 3 T Continuous vibration at 14 to 150 Hz: 4.9 m/s2 or less
and Describes the limit control functions.
For standard signal, burnout is determined to have occurred Limit Control Output Entrance 4
Cable
1
Short-period vibration: 14.7 m/s2, 15 seconds or less
description of Functions CAUTION if it is 0.1 V or less. • Relay contact output (Standard type: terminals 1 - 2 - 3 ) Outlet
Shock: 147 m/s2 or less, 11 ms
limit control function
• Input bias current: 0.05 A (for TC or RTD b-terminal) Installation height: Height above sea level of 2000 m or less
Turn off the power to the controller before installing it on the panel because there is a possibility of electric shock. Number of outputs 1 • EMC standards: Complies with EN61326, EN61000-3-2,
• Measurement current (RTD): About 0.13 mA Warm-up time: 30 minutes or more after power on
• Input resistance: 1 M or more for thermocouple or mV input Output signal Three terminals (NC, NO, and common) EN61000-3-3 and EN55011 (CE). Installation category based on IEC61010-1 : II (See Note)
1. Safety Precautions After opening the mounting hole on the About 1 M for DC voltage input Contact rating 250V AC or 30V DC, 3A (resistance load)
Class A Group 1. Pollution degree based on IEC61010-1 : 2 (See Note)
Large bracket • Allowable signal source resistance: 250 or less for The instrument continues to operate at a measuring
The following symbol is indicated on the controller to ensure safe use. panel, follow the procedures below to in- Resolution 10 ms accuracy of within 20% of the range during tests.
Panel (top mounting hardware) thermocouple or mV input Note :
stall the controller: Effects of signal source resistance: 0.1 V/ or less •The “Installation category” implies the regulation for
CAUTION Construction, Installation, and Wiring
2 k or less for DC voltage input Contact Inputs • Construction: Only the front panel is dust-proof and drip-proof
impulse withstand voltage. It is also called the
1. Insert the controller into the opening Effects of signal source resistance: About 0.01%/100 • Purpose: Confirmation of limit output. “Overvoltage category.” “II” applies to electrical
• Allowable wiring resistance: for RTD input (protection class IP55)
This symbol on the controller indicates that the operator must refer to an explanation in the user’s manual in order from the front of the panel so that the ter- • Number of input: 1 equipment.
Maximum 150 /wire: Conductor resistance between three For side-by-side close installation the controller loses its
to avoid the risk of injury or death of personnel or damage to the instrument. The manual describes how the operator minal board on the rear is at the far side. • Input type: Non-voltage contact or transistor open collector input •“Pollution level” describes the degree to which a
Terminal board wires should be equal dust-proof and drip-proof protection.
should exercise special care to avoid electric shock or other dangers that may result in injury or loss of life. Direction to insert the • Input contact rating: 12 V DC, 10 mA or more solid, liquid or gas which deteriorates dielectric
controller However, 10 /wire for a maximum range of -150.0 to • Material: ABS resin and polycarbonate
• On/off determination: For non-voltage contact input, contact strength is adhering. “2” applies to a normal indoor
2. Set the brackets in place on the top and 150.0C. • Case color: Black
Insert the controller resistance of 1 k or less is determined as “on” and contact atmosphere.
The following symbols are used in the hardcopy user’s manuals. into the opening at bottom of the controller as shown in the Wire resistance effect: 0.1C /10 • Weight: About 1 kg or less
resistance of 20 k or more as “off.” • Transportation and storage conditions:
the front of the panel. Insert a screwdriver into the figure on the left, then tighten the screws • Allowable input voltage: 10 V DC for thermocouple, mV, or For transistor open collector input, input voltage of 2 V or • Dimensions:
Temperature: -25 to 70C
NOTE brackets to tighten the screws. of the brackets. Take care not to over- RTD input less is determined as “on” and leakage current must not 96 (W) 96 (H) 100 (depth from panel face) mm
Temperature change rate: 20C/h or less
20 V DC for DC voltage input exceed 100 A when “off.” • Installation: Panel-mounting type. With top and bottom
tighten them. Humidity: 5 to 95% RH (no condensation allowed)
• Noise rejection ratio: 40 dB (50/60 Hz) or more in normal mode • Minimum status detection hold time: About 1 second. mounting hardware (1 each)
• Effects of changes in operating conditions
Indicates that operating the hardware or software in a particular manner may damage it or result in a system failure. 120 dB (50/60 Hz) or more in common mode • Devices connected to the UT350L must comply with IEC61010 • Panel cutout dimensions:
Small bracket - Effects from changes in ambient temperature:
• Reference junction compensation error: 1.0C (15 to 35C) and 60950. 92+0.8 (W) 92+0.8 (H) mm
(bottom mounting hardware)
0 0 - On voltage or thermocouple input, 1 V/C or 0.01%
1.5C (0 to 15C, 35 to 50C) • Installation position: Up to 30° upward facing
IMPORTANT Contact Outputs (not designed for facing downward)
of F.S./C, whichever is larger
• Applicable standards: JIS, IEC, DIN (ITS-90) for thermocouples
• Purpose: Alarm output, FAIL output - On RTD input, 0.05C /C (ambient temperature) or less
• Wiring: M3.5 screw terminals (for signal wiring and power/
and RTD
• Number of outputs: 2 - On analog output, 0.05% of F.S./C or less
ground wiring as well)
Draws attention to information that is essential for understanding the operation and/or features of the controller. - Effects from power supply fluctuation (within rated voltage
4. How to Connect Wires • Relay contact rating: 240 V AC/1 A or 30 V DC/1 A (COM
terminal is common) ; 1a , FAIL output ; 1b range)
• Devices connected to the UT350L must comply with IEC61010 - On analog input, 1 V/10 V or 0.01% of F.S./10 V,
2. Model and Suffix Codes CAUTION and 60950. equal to or less than whichever is larger
- On analog output, 0.05% of F.S./ 10 V or less
Before using the controller, check that the model and suffix codes match your order.
1) Before carrying out wiring, turn off the power to the controller and check that the cables to be connected are not
6. Terminal Wiring Diagrams
NOTE
Model Suffix Code Description alive with a tester or the like because there is a possibility of electric shock. Do not use unassigned terminals as relay terminals.
UT350L Limit controller 2) For safety, be sure to install a circuit breaker switch (of 5A and 100V AC or 220V AC, and that conforms to 䊏 Receiving 4-20 mA DC Current
Limit control output PV input See Initial Settings User’s Manual ,
IEC60947) near the controller so as to be operated easily, and clearly indicate that the device is used to de- Signals with the Controller
Type -0 Standard type Relay contact output RS-485 communication * Wiring can only be carried out for more information.
energize the controller. * When receiving 4-20 mA DC current signals,
0 None for controllers with TC input RTD input
Optional functions 3) Wiring must be carried out by personnel who have basic electrical knowledge and practical experience. NC 1 set the PV input type to 1-5 V DC (setpoint “41”).
1 With communication communication functions.
23 SDB(+) Maximum baud rate: 9600 bps 11 A
NO 2 12 + 12 +
Check that the following items are provided:
• Limit controller (of ordered model): .............................................................. 1
NOTE 24 SDA(-) 12 b
COM 3 13 - 250 4-20mA
• Brackets (mounting hardware): ...................................................................... 1 pair 25 RDB(+) 13 B 13 -
• Unit label: ....................................................................................................... 1 1) Provide power from a single-phase instrument power supply. If there is a lot of noise in the power line, insert an Contact rating: 250 V AC, 3 A
• User’s Manuals: .............................................................................................. 3 (A2 size) 30 V DC, 3 A (resistance load)
insulating transformer into the primary side of the line and use a line filter (recommended part: ZAC2205-00U 26 RDA(-) mV/V input
• User’s Manual (Model UT350L Communication Functions): ....................... 1 (A5 size) from TDK) on the secondary side. Note: Connecting a 250 resistor to the terminals is
Supplied only for UT350L model with communication functions. 27 SG optional.
As a countermeasures against noise, do not place the primary and secondary power cables close to each other. 12 + Model: X010-250-2 (resistor with M3.5 crimp-on terminal
2) For thermocouple input, use shielded compensating lead wires for wiring. For RTD input, use shielded wires lugs)
3. How to Install that have low conductor resistance and cause no significant differences in resistance between the three wires. 13 -
The cables to be used for wiring, terminal specifications, and recommended parts are as shown below. 1 21 11
NOTE 3) Control output relays may be replaced. However, because they have a life of 100,000 times that of the resis-
tance load, use auxiliary relays to turn on/off a load. 2 12
Alarm output
To install the controller, select a location where: 4) The use of inductance (L) loads such as auxiliary relays, motors and solenoid valves causes malfunction or UT 3 23 13
(1) no one may accidentally touch the terminals, relay failure; always insert a CR filter for use with alternating current or a diode for use with direct current, as Alarm-1 output
AL1 6 4 24 14
(2) mechanical vibrations are minimal, a spark-removal surge suppression circuit, into the line in parallel with the load.
Relay
(7) no wind blows against the terminal board (reference junction compensation ■ For DC Relay Wiring ■ For AC Relay Wiring 30 V DC, 1 A (resistance load) 8 18 17 -
150mm
element), UT350L External AC power supply 9 19 Load resistance: 600 or less
(8) no water is splashed, UT350L External DC power supply
(9) no flammable materials are around, 10 30 20
Manual Limit Controller User’s Manual 1. Bring the operating display into view (display
appears at power on).
10. Press the key once to display the parameter
SET/ENT
“UNIT”. -199.9 to 500.0⬚C ⫾0.1% of instrument range ⫾1 digit for temperatures power-on). parameter “AL1” (alarm-1 type).
3
-199.9 to 999.9⬚F equal to or higher than 0⬚C
4th Edition: Apr. 1, 2005 Displays target -199.9 to 999.9⬚C ⫾0.2% of instrument range ⫾1 digit for temperatures Displays Displays
J 4
setpoint. -300 to 2300⬚F below 0⬚C PV. parameter
-199.9 to 400.0⬚C “AL1”.
5
-300 to 750⬚F
T
0.0 to 400.0⬚C Displays target
2. Press the key for more than 3 seconds to 11. Press the key once to display the parameter
SET/ENT SET/ENT
This manual describes examples of setting PV input types, limit control types, and alarm types. 6
-199.9 to 750.0⬚F
call up the menu “OP.PA”. “RH” (maximum value of PV input range). setpoint.
Carrying out settings described herein allows you to perform basic control. ⫾0.15% of instrument range ⫾1 digit for temperatures
Refer to examples of various settings to understand how to set parameters required. Refer to “1. Basic Key Operation Displays Displays 0 to 1800⬚C equal to or higher than 400⬚C
B 7
Sequence and Parameter Map” in Parameters and Functions User’s Manual for an easy to understand explanation menu “OP.PA”. parameter 32 to 3300⬚F ⫾5% of instrument range ⫾1 digit for temperatures
“RH”. below 400⬚C 2. Press the key for more than 3 seconds to
SET/ENT
4.
“PWD”. ⫾0.5% of instrument range ⫾1 digit for temperatures
2. Setpoint display 0 to 1900⬚C
3. EXCEEDED lamp PR20-40 17 equal to or higher than 800⬚C
32 to 3400⬚F
No guarantee of accuracy for temperatures below 800⬚C Press the key once to display the 9. Press the key for more than 3 seconds.
4.
SET/ENT SET/ENT
W97Re3- 0 to 2000⬚C parameter “PWD”. This returns you to the display shown at power-on
18 ⫾0.2% of instrument range ⫾1 digit
5. Alarm indicator lamps 4. Output indicator lamp W75Re25 32 to 3600⬚F (figure below).
-199.9 to 500.0⬚C
30 ⫾0.1% of instrument range ⫾1 digit (Note1) (Note2)
8. and keys -199.9 to 999.9⬚F Displays
6. RESET key JPt100
-150.0 to 150.0⬚C PV.
31 ⫾0.2% of instrument range ⫾1 digit (Note1)
7. SET/ENT key -199.9 to 300.0⬚F
-199.9 to 850.0⬚C
5. Press the
SET/ENT
SET/ENT Used to switch or register a parameter. Pressing the key for more than 3 seconds allows you to switch 3. Changing Limit Control Type ■ List of Alarm Types
7. Blinks during
key between the operating display and the menu for operating parameter setting display alternately.
change. The following operating procedure describes an example of changing limit control type (factory-set default: high limit type) The table below shows the alarm types and alarm actions.
Used to change numerical values. On setting displays for various parameters, you can change to low limit type. In the table, codes 1 to 10 are not provided with stand-by actions, while codes 11 to 20 are provided with stand-by actions.
and target setpoints and parameters. Pressing the key decreases a numerical value,
8. Alarm type code Alarm type code
keys 1. Bring the operating display into view (display 6. Press the key several times to display the
SET/ENT
while pressing the key causes it to increase. You can hold down a key to gradually increase Alarm action Alarm action
7. Press the key once to display the parameter 16. Press the key once to register the setpoint.
SET/ENT SET/ENT
the speed of change. appears at power on). parameter “HI.LO” (limit control type selection). Alarm type
Contact Contact
Alarm type
Contact Contact
“IN” (PV input type). “Open/close” shows status of relay contact, closes opens “Open/close” shows status of relay contact, closes opens
if alarm if alarm if alarm if alarm
Displays and “lit” and “unlit” shows status of lamp occurs occurs and “lit” and “unlit” shows status of lamp occurs occurs
Displays Displays
parameter
IMPORTANT parameter “IN”. PV.
“HI.LO”.
No alarm OFF Hysteresis
Hysteresis De-energized 6
1 Open (lit) Closed
on deviation low
The controller automatically returns to the display at the time of power-on (i.e., operating display) if no key is Displays target PV high limit Open (unlit) Closed (lit) limit alarm Deviation
(unlit)
PV 16
operated for at least one minute. setpoint. 11 setpoint
PV Alarm setpoint Target SP
Hysteresis Hysteresis
Hysteresis
2. Press the key for more than 3 seconds to
SET/ENT
2 7
■ Setting of Main Parameters at the Factory before Shipment 8. Press the or key to display the required 17. Press the key for more than 3 seconds.
SET/ENT
9. Press the key once to register the setpoint. * If the type of input is voltage, also configure 3. Press the key once to display the menu
SET/ENT
The controller is configured to the initial value of each parameter at the factory before shipment. Minimum Value of PV Input Scale (SL) that are Displays menu Hysteresis
Hysteresis
First check the initial values shown in “2. Lists of Parameters,” in Parameters and Functions User’s Manual and displayed after parameter RL. “STUP”. De-energized on 5 10
Closed Open (lit) De-energized Closed
deviation high Open (lit)
change parameter values as necessary. limit alarm
(unlit)
Deviation
on PV low limit (unlit)
PV setpoint 15 20
Alarm setpoint PV
Target SP
Example of Temperature Input Example of Voltage Input The controller stops when in a FAIL state.
Fault diagnosis FAIL output The control output is set to “OFF”,
-300°F 2500°F 1V 2V 4V 5V (input signal) output (Note 1)
Fault diagnosis output 21 (Note 2)
22
alarm output is set to “OFF” and
Instrument
Instrument
input range NOTE 4. Press the
SET/ENT
key once to display the parameter 9. Press the key for more than 3 seconds.
SET/ENT
retransmission output is set to 0%.
input range “PWD”. This returns you to the display shown at power on
Set a range The controller may automatically initialize the registered operating parameter setpoints if any change is made to the (figure below).
PV input range RH
PV input range to be
RL
data item PV Input Type (IN), Maximum Value of PV Input Range (RH), Minimum Value of PV Input Range (RL),
Stand-by Action
controlled Set a range to Displays
0°F 800°F be controlled PV Input Decimal Point Position (SDP), Maximum Value of PV Input Scale (SH) or Minimum Value of PV Input PV.
PV input scale
Minimum value of Maximum value of ⬚C
PV input range (RL) PV input range (RH) 0.0m3/h 50.0m3/h
Scale (SL). After a change has been made to any of these data items, be sure to verify the registered operating Normal Abnormal
Treated
Minimum value of Maximum value of parameter setpoints to ensure that they are correct. If any data item has been changed to its default, set it to a Displays target The alarm
as normal
PV input scale (SL) PV input scale (SH) required value. setpoint. output turns on.
Parameters to be set for temperature input Parameters to be set for voltage input Low limit of
1. PV input type (IN): Set according to a sensor 1. PV input type (IN): Set according to an input signal alarm setpoint
2. Maximum value of PV input range (RH): Set the 2. Maximum value of PV input range (RH): Set the maximum value of an input signal.
Press the key once to display the menu
SET/ENT
maximum value of the range to be controlled. 3. Minimum value of PV input range (RL): Set the minimum value of an input signal. 5. The alarm output does not
3. Minimum value of PV input range (RL): Set the 4. Position of PV input decimal point (SDP): Set the position of the decimal point for PV input display. “FUNC”.
minimum value of the range to be controlled. 5. Maximum value of PV input scale (SH): Set the maximum value of the scale to be controlled. turn on in this region even
6. Minimum value of PV input scale (SL): Set the minimum value of the scale to be controlled. if the PV value is below the
Displays low limit of the alarm setpoint.
menu “FUNC”.
Power-on Time
IM 05D01D21-02E (1)
3. Setting Alarm Setpoints 5. Operation in Confirmation Display ■ Errors at Power On
The following operating procedure describes an example of setting Alarm output terminals Following parameters can be seen in the confirmation display. These parameters can be confirmed and reset by pressing the
User’s Model UT350L 160.0 to alarm-1 setpoint. Check alarm type before setting the alarm Alarm-1 (terminal numbers 6 - 7
Factory-set defaults
)............PV high limit alarm key at each parameter display.
The following table shows errors that may be detected by the fault diagnosis function when the power is turned on.
Error indication
Manual Limit Controller User’s Manual setpoint. To change the type of alarm, see “4. Changing Alarm Type” Alarm-2 (terminal numbers
in Initial Settings User’s Manual .
5 - 7 )............PV low limit alarm
● Duration time (TIME) (on PV display unit)
Description
of error
PV
Control
output
Alarm
output
Retransmission Communi-
output cation
Remedy
Displays
Displays menu target setpoint. Press the key if reset is designated.
“OP.PA”.
Contents If you don't want to reset, just go to the step 6.
■ Possible Errors during Operation
1. Monitoring-purpose Operating and Confirmation Displays Available during Operation The following shows possible errors occurring during operations.
2. Setting Target Setpoint (SP)
3. Setting Alarm Setpoints Error indication Description PV Control Alarm Retransmis- Commu- Remedy
4. Confirmation of the Limit Output Also configure the Alarm-2 Setpoint (A2) parameter (on PV display of error output output sion output nication
5. Operation in Confirmation Display that follows this step. unit)
6. Troubleshooting Press the SET/ENT
key twice to display the parameter Press the key for more than 3 seconds. Displays “RJC” RJC error Measured
3. 6.
SET/ENT
parameter 5.
Displays PV. “TIME”. Press the key. If the instrument is specified
SET/ENT
All indications off Runaway (due None 0% or less OFF 0% or Stopped Faulty if power off/on does
Procedure 3) Confirmation of the limit output can be done either by a front panel or external contact input. press the key for about one second. display (PV/SP display). to defective or OFF less not reset start the unit.
The duration time will be reset. power or Contact us for repair.
See “3. Description of Limit Control Functions” in Parameters and Functions User’s Manual . If you don't want to reset the time, just move to the noise)
Here explains the way to reset key operation. next step.
All indications off Power off None 0% OFF 0% Stopped Check for abnormal power.
Displays PV.
1. Bring the operating display (PV/SP display or SP 3. Press the key for about one second. Confirm
When setup parameter OP.SL is When setup parameter OP.SL is that the OUT lamp becomes OFF.
set to 0. set to 1.
only display).
The output has been on. Displays
■ If a Power Failure Occurs during Operation
(factory-set default) Displays
Measured input Ex.) SP=120.0, PV=125.0, Hysteresis=5 “0.00” target setpoint.
value (PV)
Not displayed Operating Display ● Momentary power failures shorter than 20 ms
The controller is not affected at all and continues normal operation.
Displays PV.
● Power failures of 20 ms or longer
EXCEEDED lamp EXCEEDED lamp • The alarm function of the controller continues to work normally. (Alarms with the stand-by feature temporarily return
Target Target
is lit. Displays is off. 6. Troubleshooting to their stand-by state, however.)
target setpoint.
Setpoint Setpoint • Setting parameters that have already been configured retain their settings.
PV / SP display SP only display
OUT lamp ■ Troubleshooting Flow • After recovery from a power failure, limit control status is reset.
is off.
OUT lamp
If the operating display does not appear after turning on the controller’s power, follow the measures in the procedure below.
is lit. Comfirmation
If a problem appears complicated, contact our sales representative.
■ Troubleshooting When the Controller Fails to Operate Correctly
SET/ENT SET/ENT
If your control tasks are not successful, check the preset parameters and controller wiring before concluding the controller
key key
Confirm that the EXCEEDED lamp is off and the Is the instrument
2. defective? to be defective. The following show examples of troubleshooting you should refer to in order to avoid the possibility of
OUT lamp is lit.
other problems.
OUT status cannot be reset while the EXCEEDED Yes
lamp is lit.
No Is key No No No Is ● The controller does not show the correct measured value (PV).
SET/ENT
key Totally Is display Is I/O communication • The UT350L controllers have a universal input.
operation
Ex.) SP=120.0, PV=115.0, Hysteresis=5 inoperable? faulty? signal faulty? link faulty?
faulty? The type of PV input can be set/changed using the parameter “IN”. At this point, the controller must be wired correctly
Yes Yes Yes Yes Yes according to the selected type of PV input. Check the wiring first if the controller fails to show the correct PV. To do
Displays PV. this, refer to Initial Settings User’s Manual .
Check wiring on the Check the key lock Turn off power, and Check the Check the With the parameters “RH”, “RL”, “SDP”, “SH” and “SL”, it is possible to scale the input signal and change its number
EXCEEDED lamp power supply setting. then turn it on again. instrument’s I/O instrument's suffix
is off. Displays terminals. specifications. code. of decimal places. Also check that these parameters are configured correctly.
Duration time display target setpoint.
No
Check the supply Check the specifications Does the code
SET/ENT
key SET/ENT
key Confirmation Display OUT lamp voltage. of I/O counterpart for
wrong polarity.
include a communication
option?
7. Cleaning and Maintenance
is lit.
When limit control type is When limit control type is
set as high limit.
(factory-set default)
set as low limit.
No
■ Cleaning
Check the
No communication
Normal? capability.
communication-related Use a dry cloth and wipe gently to clean the product’s front panel, keys, and other areas.
No Is parameters.
key lock
enabled? NOTE
Yes Check
Correct
communication wiring. Do not use solvents such as alcohol or benzine.
■ Confirmation of Limit Status errors.
Limit control output and related parameter such as duration time and maximum / minimum PV value can be confirmed by a
Maximum value display Minimum value display No Check the specifications
front key operation. It is possible to confirm limit control output by using external contact input. The way of confirmation
is set by setup parameter DIS.
Correct? of communication
counterpart.
■ Replacing the Mounting Bracket
Table blow shows the item which can be confirmed by front key or external contact input according to the setting of DIS. Yes Yes If the mounting bracket is damaged or lost, order a replacement using the following serial number and sales unit.
Disable
key lock.
Part No. Sales Unit
DIS parameter = KEY DIS parameter = DI
Item to be confirmed Ask the vendor for repair. Find the cause. T9115NL One pair (upper and lower bracket)
KEY DI KEY DI
Output relay Able Disable Disable Able
Duration time Able Disable Able Disable IMPORTANT ■ Limited Life Componets and Maintenance
Maximum / Minimum value Able Disable Able Disable
Take note of the parameter settings when asking the vendor for repair. The parts used in this product that have an especially limited life are shown below.
2. Setting Target Setpoint (SP) Part No. Service Life
The following operating procedure describes an example of setting 120.0 to a target setpoint.
Aluminum electrolytic capacitor About 10 years (Estimated)
1. Bring the operating display into view (display 3. Press the SET/ENT
key once to register the setpoint. Non-volatile memory Can be written to up to 100,000 times
appears at power on). Alarm output relay 100,000 times
Limit control output relay (Note) 100,000 times
Displays PV. Note) Limit control output relay can be replaced by users.
Displays
target setpoint.
Blinks during
change.
IM 05D01D21-02E (2)
Description of Operating Parameter Menu Display Description of Setup Parameter Menu Display
2. Lists of Parameters
User’s Model UT350L Displays the
operating
Displays the
setup ■ Operating Parameters ■ Setup Parameters
Manual Limit Controller User’s Manual parameter
menu symbol
parameter
menu symbol ● Control Function-related Parameters
“OP.PA”. “FUNC” or “I/O”. Parameter
Name of Parameter Setting Range and Description Initial Value User Setting
Nothing appears. Nothing appears. Symbol Parameter
Name of Parameter Setting Range and Description Initial Value User Setting
Symbol
IM 05D01D21-03E Parameters and Functions Target setpoint 0.0 to 100.0% of PV input range 0.0% of PV input range
OFF, 1 to 22
Alarm-1 type 1
(SP) 1: PV high limit (energized, no stand-by action)
2: PV low limit (energized, no stand-by action)
4th Edition: Apr. 1, 2005 Alarm-1 setpoint PV alarm: -100.0 to 100.0% of PV input range PV high limit alarm: (AL1) 3: Deviation high limit (energized, no stand-by action)
Description of Operating Parameter Setting Display Description of Setup Parameter Setting Display Deviation alarm: -100.0 to 100.0% of PV input 100.0% of PV input range 4: Deviation low limit (energized, no stand-by action)
(A1) Alarm-2 type 2
range span Deviation alarm: 0.0% of PV 5: Deviation high limit (de-energized, no stand-by action)
Alarm-2 setpoint input range span 6: Deviation low limit (de-energized, no stand-by action)
Displays a Displays a
Other PV low limit alarm: (AL2) See “List of Alarm Types” in Initial Settings User’s Manual .
parameter parameter
This manual contains a parameter map as a guideline for setting parameters, and lists of parameters for recording User symbol. symbol. (A2) 0.0% of PV input range 0.0 to 100.0% of PV input range span
Alarm-1 hysteresis 0.5% of PV
Settings. PV input filter OFF, 1 to 120 seconds. OFF input range span
Hysteresis for PV high limit alarm
Displays a Displays a Used when the PV input fluctuates. Point of
Contents setpoint. setpoint. (FL) (HY1) Output on-off action
(Alarm setpoint)
PV input bias -100.0% to 100.0% of PV input range span 0.0% of PV input range On
1. Basic Key Operation Sequence and Parameter Map Used to correct the PV input range. span Alarm-2 hysteresis
2. Lists of Parameters (BS)
Off Hysteresis
3. Description of Limit Control Functions Limit control output 0.0 to 100.0% of PV input range span 0.5% of PV input range span (HY2)
4. Parameters in the Confirmation Displays hysteresis
5. Function Block Diagram ? (H)
In case of HIGH LIMIT
Limit control type selection HI: High limit, LO: Low limit HI
Output
If you become unsure of key operation during parameter SP
(HI.LO)
setting, hold down the key for more than 3 seconds.
SET/ENT
On
1. Basic Key Operation Sequence and Parameter Map This returns you to the display at power-on Restart mode 0: Limit output is ON at power on in any cases,
(i.e., operating display). 0
Hysteresis 1: Limit output is OFF at power on when PV doesn’t
Off
(R.MD) exceed SP
Power on PV
0
Operating display 0: PV/SP display first,
In case of LOW LIMIT selection 1: SP only display first
(OP.SL)
Output
SP 0: hour and minute 0
Time unit for duration time
On
Operating Display Confirmation Display 1: minute and second
(TMU)
Off
Measured input Hysteresis Protocol selection 0: PC link communication
0
value (PV) 1: PC link communication (with sum check)
PV 2: Ladder communication
When limit control type is (P.SL)
When setup parameter set as “high limit.”
(factory-set default) Baud rate 0: 600, 1: 1200, 2: 2400, 3: 4800, 4: 9600 (bps)
OP.SL is set to “ 0.” 4
(factory-set default) SET/ENT
key
SET/ENT
key
SET/ENT
(BPS)
key
Target 0: None
Parity
Setpoint Maximum value display 1: Even 1
PV / SP display
(PRI) 2: Odd
● Input-/Output-related Parameters
Parameter
Name of Parameter Setting Range and Description Initial Value User Setting
Basic Key Operation Sequence Symbol
SET/ENT
key SET/ENT
key
PV input type (INPUT OFF, 1 to 18, 30, 31, 35 to 37, 40, 41, 50, 51, 55, 56 1
1. Setting display can be switched (moved) using the key.
SET/ENT
key
SET/ENT
key key
IM 05D01D21-03E (1)
3. Description of Limit Control Functions ■ Power on Status 4. Parameters in the Confirmation Displays 5. Function Block Diagram
The state of output relay at power-on can be set by a setup parameter restart mode R.MD.
PV input Contact input
■ In Case of High Limit Control ■ Duration Time terminals terminals
Setup Parameters
When a measured value (PV) exceeds a setpoint (SP). “EXCEEDED” lamp lights, and “OUT” lamp turns ON (point A). The limit control Restart mode R.MD : The time while PV exceeds SP is counted and stored in the memory. It is displayed in the “TIME” display in the confirmation display. 11 , 12 and 13 19 and 20
output relay is de-energized then. 0 : Limit output relay is de-energized at power on.
“EXCEEDED” lamp turns off when PV goes into normal condition, while “OUT” lamp stays on as it is (point B). “OUT” lamp turns off 1 : Limit output relay is energized at power on.
when a confirming operation is done by an operator (point C). The way to confirm is pushing the “RESET” key (or by an exeternal contact, Display time range : 0.00 to 99.59 PV INPUT DI
according to the setting of setup parameter DIS). The confirming operation is not accepted during PV exceeds SP (point D). State of output
relay is de-energized whenever “OUT” lamp is on. (NC terminal : CLOSE, NO terminal : OPEN) ● When parameter R.MD is set to 0. Unit of time is be either “hour.minute” or “minute.second”, and can be set by setup parameter TMU.
The limit output relay is always de-energized at power on, even if PV doesn’t exceed SP (point A). (NC terminal : CLOSE, NO terminal : DIS
OPEN). “OUT” lamp is lit. After the confirmation, state of output relay is energized (NC terminal : OPEN, NO terminal : CLOSE) and “OUT” Input selection IN
(A) (B) (C) (A) (D) (B) lamp turns off, if the PV doesn’t exceed SP (point B). - To RESET
- Push “RESET” key for about one second to reset the duration time in the confirmation display where “TIME” is displayed. Unit selection UNIT
When the count are reset, “0.00” is displayed until PV exceeds SP again. Input range conversion RH,RL SDP, SH, SL
In Case of High Limit Control - The time count are reset when power is turned on.
- If PV exceeds SP during the old time count data is retained in the memory, the old data should be automatically reset, and the Input bias BS
(A) (B) new time counting starts from “0.00”.
SP - It is impossible to reset the time count while PV exceeds SP by any operation. Input filter FL
- Duration time cannot be reset by an external contact input.
Hysteresis
SP
RESET
PV
SP
■ Maximum / Minimum Value PV dispay Target setpoint AL1 AL2
The maximum value or minimum value of PV is stored in the memory and display in the “HI” or “LO” display in the confirmation display. A1 A2
Hysteresis
When the control type is specified as high limit control, the maximum value is displayed in the “HI” display, and control type is specified as
RET RTH RTL HI.LO HY1 HY2
low limit control, the maximum value is displayed in the “LO” display.
EXCEEDED off lit off lit off Retransmission
PV When the PV exceeds SP and then returns to the normal status, Maximum / Minimum Value is retained as it is , but when PV exceeds SP again,
Lamp Limit control Alarm function
it is automatically reset and starts taking new value for its minimum / maximum value. output
OUT off off
lit lit H Limit
Lamp - To RESET
EXCEEDED off lit - Push the “RESET” key for about one second to reset the maximum / minimum value in the confirmation display where “HI” or PV or SP control
Lamp output
Output Relay on off on off “LO” is displayed. The value is reset, and the value immediately after the confirmation should be recognized as a maximum or
minimum value.
OUT off lit off lit off - When the power is turn on, the memory should be reset and the first PV should be recognized as maximum.
Lamp - Maximum / Minimum value cannot be reset by an external contact input.
RET OUTPUT AL1 AL2
- It is impossible to reset the maximum / minimum value while PV exceeds SP by any operation.
Output Relay off on off on Alarm 1 Alarm 2
Operation
(RESET key or Confirmation Confirmation Current Relay terminals terminals
external contact input) (accepted) (not accepted) terminals terminals 6 and 7 5 and 7
16 and 17 1 , 2 and 3
Power on
Operation
Confirmation Confirmation
■ In Case of Low Limit Control (RESET key or
(accepted) (accepted)
external contact input)
When a measured value (PV) exceeds a setpoint (SP). “EXCEEDED” lamp lights, and “OUT” lamp turns ON (point A). The limit control Terminal Parameter Function
output relay is de-energized then. Legend
“EXCEEDED” lamp turns off when PV goes into normal condition, while “OUT” lamp stays on as it is (point B). “OUT” lamp turns off Analog signal Contact signal Front panel key
when a confirming operation is done by an operator (point C). The way to confirm is pushing the “RESET” key (or by an exeternal contact, ● When parameter R.MD is set to 1.
according to the setting of setup parameter DIS). The confirming operation is not accepted during PV exceeds SP (point D). State of output
The limit output relay is always energized at power on (point A) (NC terminal : OPEN, NO terminal : CLOSE) and “OUT” lamp is off, except
relay is de-energized whenever “OUT” lamp is on. (NC terminal : CLOSE, NO terminal : OPEN)
when PV exceeds SP at power on.
Hysteresis
SP
SP
Hysteresis
PV
EXCEEDED off lit off lit off
Lamp
EXCEEDED off lit
OUT off off Lamp
lit lit
Lamp
OUT off lit off
Output Relay on off on off Lamp
Operation
(RESET key or Confirmation Confirmation
external contact input) (accepted) (not accepted) Power on
Operation
(RESET key or Confirmation
external contact input) (accepted)
IM 05D01D21-03E (2)