Академический Документы
Профессиональный Документы
Культура Документы
ENGLISH
VIDEO CASSETTE RECORDER
HR-V505/V506/V507E
HR-V205/V206E
INSTRUCTIONS
LPT0811-001A Printed in Indonesia
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD. 0203-AH-CR-LG
IMPORTANT
䡲 Please read the various precautions on page 1 and 2 before
installing or operating the recorder.
䡲 It should be noted that it may be unlawful to re-record pre-
recorded tapes, records, or discs without the consent of the
owner of copyright in the sound or video recording,
broadcast or cable programme and in any literary, dramatic,
musical, or artistic work embodied therein.
—1—
For Italy:
MOISTURE CONDENSATION
“It is declared that this product, brand JVC, conforms to the Moisture in the air will condense on the recorder when you move
Ministry Decree n. 548 of 28 Aug.’95 published in the Official it from a cold place to a warm place, or under extremely humid
Gazette of the Italian Republic n. 301 of 28 Dec.’95” conditions—just as water droplets form on the surface of a glass
filled with cold liquid. Moisture condensation on the head drum
will cause damage to the tape. In conditions where condensation
The STANDBY/ON 1 button does not completely shut off may occur, keep the recorder’s power turned on for a few hours to
mains power from the unit, but switches operating current on let the moisture dry.
and off. “`” shows electrical power standby and “ ! ” shows
ON.
How to use the remote control
For HR-V505/V506/V507E owners: Before use, insert the Lithium battery (CR 2032) in the correct
Video tapes recorded with this video recorder in the LP (Long directions as indicated back of the remote control. The remote
Play) mode cannot be played back on a single-speed video control can operate most of your recorder’s functions, as well as
recorder. basic functions of JVC TV sets.
● Point the remote control toward the receiving window on the
recorder.
For HR-V205/V206E owners: ● The maximum operating distance of the remote control is about
Video tapes recorded with another recorder in the LP (Long 7.5 m.
Play) mode cannot be played back on this video recorder. ● To operate your JVC TV, press the corresponding button:
TV 1, TV , TV PR +/, TV %+/ (TV Volume).
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation NOTE:
(10 cm or more on both sides, on top and at the rear). If the remote control does not work properly, remove its batteries,
wait for a few seconds, replace the batteries and then try again.
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly. Video heads cleaning
Accumulation of dirt and other particles on the video heads may
Failure to heed the following precautions may result in damage to cause the playback picture to become blurred or interrupted. Be
the recorder, remote control or video cassette. sure to contact your nearest JVC dealer if such troubles occur.
1. DO NOT place the recorder …
… in an environment prone to extreme temperatures or
humidity. Usable cassettes
… in direct sunlight. ● Compact VHS camcorder recordings can
… in a dusty environment. be played on this recorder. Simply place
… in an environment where strong magnetic fields are the recorded cassette into a VHS Cassette
generated. Adapter and it can be used just like any
… on a surface that is unstable or subject to vibration. full-sized VHS cassette.
2. DO NOT block the recorder’s ventilation openings or holes. ● This recorder can record on regular VHS and Super VHS
(If the ventilation openings or holes are blocked by a cassettes. However, it will record and play back regular VHS
newspaper or cloth, etc., the heat may not be able to get out.) signals only. It is not possible to play back a recorded Super
3. DO NOT place heavy objects on the recorder or remote VHS cassette.
control.
4. DO NOT place anything which might spill on top of the ATTENTION:
recorder or remote control. To mobile phone users:
(If water or liquid is allowed to enter this equipment, fire or Using a mobile phone in the vicinity of the recorder may cause
electric shock may be caused.) picture vibration on the TV screen or change the screen to a
5. DO NOT expose the apparatus to dripping or splashing. blue back display.
6. DO NOT use this equipment in a bathroom or places with On placing the recorder:
water. Also DO NOT place any containers filled with water or Some TVs or other appliances generates strong magnetic fields.
liquids (such as cosmetics or medicines, flower vases, potted Do not place such appliance on top of the recorder as it may
plants, cups, etc.) on top of this unit. cause picture disturbance.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the recorder during transport.
—2—
Number keys
AV
Easy Power
Record7 Playe off
PR +/–
Fast Child Lock SP/LP (p)
Infrared beam Forward5 Rewind3 Fast Forward
receiving window 5
Play4
Record7[ITR] Pause9
Display panel Stop8
A Tape-in Indicator
B REC Indicator
C VCR Indicator
D Timer Indicator
See “ATTENTION”
below.
* HR-V505/V506/V507E only
ATTENTION:
Do not drop the tying band for fixing the
main power cord into the inside of the
recorder. It may cause a malfunction.
—3—
Icon Description
—4—
Icon Description
Basic Connections
F ABC OSD Select this icon to set the language. You can
select among 7 languages. (墌 7) A Check contents
Make sure the package contains all of the accessories listed in
“Specifications” (墌 16).
H OSD ON / OFF
When this function is set to “ON”, various
recorder status information (on-screen display)
appears on the screen.
NOTE:
When you use the recorder as the source player
for editing a tape, be sure to set this function to
OFF. Otherwise, the recorder status TV aerial cable
information will be recorded on the edited tape. 21-pin SCART
connector
I 16:9/4:3 AUTO / 16:9 / 4:3
You can select the aspect ratio of your TV. 21-pin SCART cable RF cable
AUTO: Normally select this. You can play back (not provided) (provided)
the 16:9 and 4:3 screen-programme as they are.
16:9: You can play back the programme with
the 16:9 screen format.
4:3: You can play back the programme with the
4:3 screen format.
NOTE: Mains power cord
Set your TV to its AV mode if the picture is cut AERIAL
off on the screen when you play back the
programme with the 16:9 screen format.
J DECODER ON / OFF
Set “DECODER” to “ON” when you use a
decoder connected to the EURO AV2
DECODER connector.
—5—
—6—
—7—
—8—
—9—
— 10 —
Turn on the TV and select the AV mode or video channel. Specifying recording length
— Instant Timer Recording (ITR)
A Load a cassette During recording, press 7 (ITR) repeatedly until the desired
Make sure the record safety tab is intact. If not, cover the hole recording length appears on the screen.
with adhesive tape before inserting the cassette. ● Each time you press the button, recording length increases in
● The recorder turns on, and the counter is reset, automatically. 30-minute intervals (up to 9 hours).
B Select recording channel ● The recorder enters the standby mode after recording is
finished.
Press PR+/ or the number keys. ● To cancel an ITR, press 8 on the remote control or 0 on the
● You can select channel in the stop mode or recording pause recorder.
mode.
C Set tape speed (HR-V505/V506/V507E only) Receiving stereo and bilingual programmes
Press SP/LP (p). The current setting for the tape speed appears
on the screen for about 3 seconds. Press SP/LP (p) again to (HR-V505/V506/V507E only)
change the setting while tape speed is displayed. Your recorder is equipped with a Sound-Multiplex decoder (A2)
D Start recording and a Digital stereo sound decoder (NICAM) as well, making
reception of stereo and bilingual broadcasts possible.
Press 7. ● To listen to a stereo programme, set “AUDIO” to “STEREO”.
● If the tape reaches its end during recording, the recorder stops (墌 5)
recording, rewinds the tape and ejects the cassette, then enters ● To listen to a bilingual programme, set “AUDIO” to “LEFT” or
the standby mode automatically. “RIGHT”. (墌 5)
● To listen to the standard (regular monaural) audio while
During recording receiving a NICAM broadcast, set “AUDIO” to “MONO”.
(墌 5)
Pause recording
NOTE:
Press 9. Set OSD to ON to display the indications on the screen.
● Press 9 to resume recording. (墌 5)
● You can select channel in the recording pause mode.
● There will be a loss of color, or the picture will be distorted
where the channel is changed. To record stereo and bilingual programmes (A2)
Stop recording ● Stereo programmes are automatically recorded in stereo on the
Hi-Fi audio track (with the normal audio track recording mixed
Press 8 on the remote OR Press 0 on the recorder. L and R channel sound).
control. ● Bilingual programmes are automatically recorded in bilingual
on the Hi-Fi audio track. The main soundtrack is recorded on
the normal audio track.
Recording Features
To record NICAM stereo and bilingual programmes
Tape Position/Time Counter The NICAM audio programme is recorded on the Hi-Fi audio
Press OK repeatedly to display the tape position and time track, and the standard audio programme on the normal audio
counter on the screen. To reset the time counter, press 0000. track.
NOTES: NOTES:
● Set OSD to ON to display the indications on the screen. ● Set NIC to AUTO. (墌 5)
(墌 5) ● If the quality of stereo sound being received is poor, the
● Depending on the type of tape used, the tape position may not broadcast may be received in monaural with better quality.
appear right away. ● Before playing back a programme recorded in stereo, or a
bilingual programme, set AUDIO to the appropriate mode.
(墌 5)
Memory Stop Facility
The recorder stops automatically when rewinding the tape and the
counter reaches “M 0:00:00”. If you set the counter to
“M 0:00:00” before the playback or recording, you can easily
access the pre-selected position by using the time counter.
A Press OK repeatedly to display the counter on the screen.
B Press 0000 to reset the counter before playback or recording.
C Start playback or recording.
D Press 3 after playback or recording. The tape rewinds and
stops automatically when the counter reaches to “M 0:00:00”.
— 11 —
— 12 —
— 13 —
A Make connections
Editing Connection with another video recorder
Connect EURO AV1 AUDIO/VIDEO or EURO AV2 DECODER
connector to another video recorder.
Editing with another video recorder or a Connection with a camcorder
camcorder Connect the camcorder’s AUDIO/VIDEO OUT connectors to the
recorder’s EURO AV1 AUDIO/VIDEO or EURO AV2 DECODER
You can use your recorder as the source player or the recording connector via a cable adapter.
deck. You can use a camcorder as the source player and your
recorder as the recording deck. Refer also to the other B Load cassettes
components’ instruction manuals for connection and its Insert the playback cassette into the source player and the cassette
operations. to be recorded on into the recording deck.
Connection with another video recorder C Select input mode on recording deck
Select the correct external input on the recording deck. On this
TV receiver Recorder Your recorder recorder, press AV and/or PR+/.
Select “AV1” for the EURO AV1 AUDIO/VIDEO connector, or
“AV2” for the EURO AV2 DECODER connector.
D Select edit mode
Select the appropriate edit mode for the components if such a
21-pin SCART cable mode is equipped.
Video
(not provided)
E Start playback
channel or Engage the Play mode of the source player.
AV mode RF cable
(provided) F Start recording
Engage the Record mode of the recording deck.
Another recorder
Player
Cable adapter
(not provided)
Audio/Video cable
AUDIO OUT (not provided)
Camcorder
VIDEO OUT
Player
— 14 —
— 15 —
VIDEO
Specifications Signal system : PAL-type colour signal and CCIR
monochrome signal, 625 lines
50 fields
GENERAL Recording Format : PAL/MESECAM
Power : 200 V – 240 Vd, 50 Hz/60 Hz RF reception : PAL (B/G)/SECAM (B/G)
Power consumption RF OUT : PAL G
Power on : Approx. 12 W RF modulator : UHF channels 22 – 68 (Adjustable)
Standby mode : 3.0 W Input level : VIDEO IN (SCART type)
Video Head system 1.0 Vp-p, 75 ohm, unbalanced
HR-V505/V506/ : DA4 (Double Azimuth) head helical Output level : VIDEO OUT (SCART type)
V507E scan system 1.0 Vp-p, 75 ohm, unbalanced
HR-V205/V206E : Rotary two-head helical scan system Signal-to-noise ratio : More than 43 dBm
Tape speed
(SP) : 23.39 mm/sec AUDIO
(LP)* : 11.69 mm/sec
* HR-V505/V506/V507E only
Input level : AUDIO IN (SCART type)
–6.0 dBm, more than 10 k˜
Tape format : Tape width 1/2"
(12.7 mm high density VHS tape) Output level
Maximum recording time HR-V505/V506/ : AUDIO OUT (SCART, RCA type)
V507E –6.0 dBm, less than 1 k˜
(SP) : 240 min. with E-240 video cassette
HR-V205/V206E : AUDIO OUT (SCART type)
(LP)* : 480 min. with E-240 video cassette
–6.0 dBm, less than 1 k˜
* HR-V505/V506/V507E only
Audio track
Rewind time : Approx. 180 sec. with E-180 cassette
HR-V505/V506/ : Mono track and Hi-Fi track
Dimensions (W x H x D) : 360 mm x 94.5 mm x 270 mm V507E
Weight : 4.0 kg HR-V205/V206E : Mono track
Operating temperature : 5°C to 35°C Audio frequency response
Operating humidity : Less than 80 % Normal audio : 100 Hz to 10,000 Hz
Timer : 24 hours display type (–6/+3 dBm)
Hi-Fi audio* : 20 Hz to 20,000 Hz
(–3/+3 dBm)
* HR-V505/V506/V507E only
Audio signal to noise ratio [HR-V505/V506/V507E only]
Hi-Fi audio : More than 70 dB (JIS A filter)
Audio dynamic range [HR-V505/V506/V507E only]
Hi-Fi audio : More than 85 dB (JIS A filter)
ACCESSORIES
Provided accessories : RF cable,
Infrared remote control unit,
“CR 2032” battery x 1
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without
notice.
— 16 —