METTULURIGICAL COMPARISON CHART BETWEEN THIRD PARTY AND SUNFLAG
Diameter : 25.10mm Heat no: 07273
S.No Properties Parameters Spec as per Tech protocol
Tensile Strength (Mpa) 930
1 Mechanical % of Elongation 13 % of Reduction in area 40 C 0.18-0.22 Si 0.15-0.25 Mn 0.75-0.85 P 0.025Max S 0.010-0.025 2 Chemical Cr 1.10-1.20 Mo 0.15-0.18 Al 0.025-0.045 Ni 0.20Max Cu 0.15Max Ti 0.0035Max 3 Grain Size GC>=6
Diameter : 22.00mm Heat no: 07938
S.No Properties Parameters Spec as per Tech protocol
Tensile Strength (Mpa) 930
1 Mechanical % of Elongation 13 % of Reduction in area 40 C 0.18-0.22 Si 0.15-0.25 Mn 0.75-0.85 P 0.025Max S 0.010-0.025 2 Chemical Cr 1.10-1.20 Mo 0.15-0.18 Al 0.025-0.045 Ni 0.20Max Cu 0.15Max Ti 0.0035Max 3 Grain Size GC>=6 Diameter : 22.30mm Heat no: 07937
S.No Properties Parameters Spec as per Tech protocol
Tensile Strength (Mpa) 930
1 Mechanical % of Elongation 13 % of Reduction in area 40 C 0.18-0.22 Si 0.15-0.25 Mn 0.75-0.85 P 0.025Max S 0.010-0.025 2 Chemical Cr 1.10-1.20 Mo 0.15-0.18 Al 0.025-0.045 Ni 0.20Max Cu 0.15Max Ti 0.0035Max 3 Grain Size GC>=6
Diameter : 20.00mm Heat no: 07976
S.No Properties Parameters Spec as per Tech protocol
Tensile Strength (Mpa) 930
1 Mechanical % of Elongation 13 % of Reduction in area 40 C 0.18-0.22 Si 0.15-0.25 Mn 0.75-0.85 P 0.025Max S 0.010-0.025 2 Chemical Cr 1.10-1.20 Mo 0.15-0.18 Al 0.025-0.045 Ni 0.20Max Cu 0.15Max Ti 0.0035Max 3 Grain Size GC>=6 T BETWEEN THIRD PARTY AND SUNFLAG REPORTS
Actual (As per External Third
Actual (As per Sunflag Mill TC) party Inspection) 1067 994 10 14.1 50 46.83 0.19 0.18 0.21 0.2 0.79 0.8 0.014 0.01 0.013 0.01 1.10 1.12 0.17 0.155 0.035 0.032 0.025 0.017 0.016 0.018 0.002 0.0028 Grain size is 8 Grain size is 7 to 7.5
Actual (As per External Third
Actual (As per Sunflag Mill TC) party Inspection) 1116 993.50 10 16.80 52 48.28 0.19 0.19 0.20 0.19 0.70 0.76 0.013 0.010 0.016 0.015 1.10 1.12 0.16 0.16 0.034 0.030 0.022 0.017 0.015 0.018 0.002 0.0030 Grain size is 7 Grain size is 7 to 7.5 Actual (As per External Third Actual (As per Sunflag Mill TC) party Inspection) 970 992.00 7 16.00 49 48.17 0.19 0.18 0.19 0.18 0.76 0.79 0.02 0.018 0.015 0.014 1.11 1.13 0.16 0.16 0.03 0.028 0.021 0.015 0.015 0.017 0.002 0.0280 Grain size is 7 to 8 Grain size is 7 to 7.5
Actual (As per External Third
Actual (As per Sunflag Mill TC) party Inspection) 1160 992.00 14 16.00 58 48.17 0.19 0.18 0.23 0.23 0.76 0.79 0.02 0.018 0.015 0.013 1.10 1.13 0.16 0.16 0.026 0.026 0.025 0.017 0.016 0.019 0.002 0.0027 Grain size is 7 to 8 Grain size is 7 to 7.5
E2788-11 Standard Specification For Use of Expanded Shale, Clay and Slate (ESCS) As A Mineral Component in The Growing Media and The Drainage Layer For Vegetative (Green) Roof Systems