Вы находитесь на странице: 1из 3

Design of Photovoltaic Systems

 Solutions: Assignment  2

1. Few photovoltaic modules are connected in series­parallel configuration as shown in 
the figure below. Each module has an I­V characteristic having the x­axis intercept as 
31V and the y­axis intercept as 4.2A. The short circuit current for the series­parallel 
system shown is

Fig.1
a) 4.2A
b) 8.4A (X)
c) 12.6A
d) 25.2A

2. For the photovoltaic module configuration shown in Figure.1, the open circuit voltage 
for the series­parallel system is
a) 93V (X)
b) 31V
c) 62V
d) 186V

3. V1 and V2 are two voltage sources having voltages 11V and 13V respectively. The series
resistance of each source is 0.25 ohms. The circulating current is 

Fig.2
a) 8A
b) 4A (X)
c) 2A
d) 24A

4. With reference to the circuit shown in Figure.2, in order to eliminate the
circulating currents, one can use diode along the path of the source current flow such that
a)  a diode is in series with the voltage source V1
b) a diode is in series with the voltage source V2
c) a diode is in series with either of the voltage sources V1 or V2
d) diodes are in series with both the voltage sources  (X)

5. A photovoltaic panel has four modules connected in series, each module having an 
open­circuit voltage (Voc ) of 10V and short­circuit current (Isc ) of 2A. What should be 
the voltage axis intercept of the I­V characteristics of the series system?
a) 10V
b) 8V
c) 40V  (X)
d) 80V

6. A photovoltaic panel has four modules connected in series, each module having an 
open­circuit voltage (Voc ) of 10V and short­circuit current (Isc ) of 2A. What should be 
the current axis intercept of the I­V characteristics of the series system?
a) 2A (X)
b) 8A
c) 4A 
d) 0.5A

7. Two dissimilar PV cells are connected in parallel (no protection diodes are 
incorporated). Let the open­circuit voltage and short­circuit current of one cell be 10V and
2A respectively. Let the open­circuit voltage and short­circuit current of the other cell be 
12V and 3A respectively. If Voc and Isc represent the open­circuit voltage and short­
circuit current of parallel cell combination, then
a) Voc < 10V
b) Voc >12V
c) Voc = 10V
d) 10V<Voc<12V (X)

8. Two dissimilar PV cells are connected in parallel (no protection diodes are 
incorporated). Let the open­circuit voltage and short­circuit current of one cell be 10V and
2A respectively. Let the open­circuit voltage and short­circuit current of the other cell be 
12V and 3A respectively. If Voc and Isc represent the open­circuit voltage and short­
circuit current of parallel cell combination, then
a) Isc < 2A
b) Isc > 3A
c) Isc = 2A
d) Isc = 3A
e) Isc = 5A (X)
f) 2A<Isc<3A

9. A PV module has 20 cells connected in series. There are no protection diodes. Each cell 
has a Voc of 1V and Isc of 2A.  One cell is completely shaded. Across the shaded cell, 
instead of a bypass diode, a resistor of 10 ohms is connected. The Voc of the PV module is
a) 19V (X)
b) 20V 
c) 0V
d) 18V
(Note: VT = 19 – 10*iT  → at iT=0, VT = Voc = 19V)

10.  A PV module has 20 cells connected in series. There are no protection diodes. Each 
cell has a Voc of 1V and Isc of 2A.  One cell is completely shaded. Across the shaded cell, 
instead of a bypass diode, a resistor of 10 ohms is connected. The Isc of the PV module is
a) 1.9A  (X)
b) 2A 
c) 0A
d) 1.6A

11. Series protection diode in the case of PV module does the job of
a) protecting the module by bypassing the voltage of the shaded panel
b) protecting the module by not allowing the flow of reverse current into it
c) increasing efficiency and protecting the module by bypassing the shaded panel 
d) increasing efficiency and protecting the module by not allowing the flow of 
reverse current into it (X)

12. A battery having a voltage of 48V is in series with a 10 ohm resistance. Across the 
terminals of this series system, a load RL is connected. Maximum power that can be 
transferred to RL is
a) 51.2 W
b) 230 W
c) 43.2 W
d) 57.6 W (X)

Note:Maximum power is transferred when RL=10 ohms.

Вам также может понравиться