Академический Документы
Профессиональный Документы
Культура Документы
CRT4485
TAD-M600
TAD-M600
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
TAD-M600 U AC 120 V
TAD-M600 Y5 AC 230 V
TECHNICAL AUDIO DEVICES LABORATORIES, INC. 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
C
F
AC Leakage Test
2 TAD-M600
1 2 3 4
5 6 7 8
A
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
C
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
TAD-M600 3
5 6 7 8
1 2 3 4
CONTENTS
SAFETY INFORMATION ..........................................................................................................................................................2
1. SERVICE PRECAUTIONS ....................................................................................................................................................5
A 1.1 NOTES ON SOLDERING ...............................................................................................................................................5
1.2 SERVICE PRECAUTIONS..............................................................................................................................................5
1.3 FOR JIG ..........................................................................................................................................................................5
2. SPECIFICATIONS .................................................................................................................................................................6
2.1 SPECIFICATIONS...........................................................................................................................................................6
2.2 PANEL FACILITIES .........................................................................................................................................................7
3. BASIC ITEMS FOR SERVICE...............................................................................................................................................8
3.1 CHECK POINTS AFTER SERVICING............................................................................................................................8
3.2 PCB LOCATIONS ...........................................................................................................................................................9
4. BLOCK DIAGRAM...............................................................................................................................................................10
4.1 OVERALL WIRING DIAGRAM......................................................................................................................................10
4.2 OVERALL BLOCK DIAGRAM .......................................................................................................................................12
B 5. DIAGNOSIS.........................................................................................................................................................................13
5.1 TROUBLESHOOTING ..................................................................................................................................................13
5.2 CIRCUIT DESCRIPTION ..............................................................................................................................................14
6. SERVICE MODE .................................................................................................................................................................19
7. DISASSEMBLY....................................................................................................................................................................20
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................36
8.1 CD ADJUSTMENT........................................................................................................................................................36
9. EXPLODED VIEWS AND PARTS LIST ...............................................................................................................................38
9.1 PACKING SECTION......................................................................................................................................................38
9.2 EXTERIOR SECTION...................................................................................................................................................40
9.3 CHASSIS SECTION .....................................................................................................................................................42
9.4 BOTTOM SECTION ......................................................................................................................................................44
C
9.5 PANEL SECTION..........................................................................................................................................................46
10. SCHEMATIC DIAGRAM ....................................................................................................................................................48
10.1 VOLTAGE AMP UNIT ..................................................................................................................................................48
10.2 POWER AMP UNIT.....................................................................................................................................................50
10.3 PRIMARY UNIT...........................................................................................................................................................52
10.4 REGULATOR UNIT .....................................................................................................................................................54
10.5 PROTECTION UNIT ...................................................................................................................................................56
10.6 LED1 and LED2 UNITS ..............................................................................................................................................58
11. PCB CONNECTION DIAGRAM ........................................................................................................................................60
11.1 VOLTAGE AMP UNIT ..................................................................................................................................................60
11.2 POWER AMP UNIT.....................................................................................................................................................64
D
11.3 PRIMARY UNIT...........................................................................................................................................................68
11.4 REGULATOR UNIT .....................................................................................................................................................70
11.5 PROTECTION UNIT ...................................................................................................................................................72
11.6 LED1 and LED2 UNITS ..............................................................................................................................................74
12. PCB PARTS LIST ..............................................................................................................................................................75
4 TAD-M600
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting A
temperatures (hard to melt/easy to harden).
• As the product weighs 90 kg, be fully careful when handling it. Four people are required when moving it.
• Be careful of the order of wire arrangement at a place where several wires are fixed together with a screw (on the power
main electrolytic capacitor, etc.), as this can affect the sound quality.
Follow the detailed procedure described in “7. DISASSEMBLY” .
• As the product has conical feet, be very careful not to scratch floor surfaces in the customer’ s home.
• Leads of power transistors supplied as service parts are NOT bent like ones used on the product.
Bend leads of supplied parts as shown the rough indication below before using.
5.8 mm 8.5 mm
7.2 mm
Power transistor
Jig for the Product (Recommended Sizes) and How to Use the Jig
Top
10 cm
40 cm
8 cm
Jig
F
As the jig holds the transformer Jig
and heatsink in place, align it with those parts.
Approx. 22 cm apart
TAD-M600 5
5 6 7 8
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
(CRB3085: TAD-M600/U)
(CRD4431: TAD-M600/Y5)
6 TAD-M600
1 2 3 4
5 6 7 8
TAD-M600 7
5 6 7 8
1 2 3 4
Check the appearance of the product. No scratches or dirt on its appearance after receiving it for
3 service.
B
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
Distortion
C
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
8 TAD-M600
1 2 3 4
5 6 7 8
PROTECTION
Unit
REGULATOR
Unit
PRIMARY
Unit
Front
C
NOTES : - Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
D
Mark No. Description Part No.
LIST OF ASSEMBLIES
PRIMARY Unit (TAD-M600/U) CWH1518
PRIMARY Unit (TAD-M600/Y5) CWH1519
PROTECTION Unit CWH1521
LED1 Unit CWH1522
LED2 Unit CWH1523
TAD-M600 9
5 6 7 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A
CN181
B2B-EH
4
1
! CN403 ! CN453
MUTE
V-12
OVLD+N
OVLD-N
AMPOUT N
GNDA
OVLD+P
OVLD-P
AMPOUT P
GNDA
CKS6112 CKS6112
OVLD-P
AMPOUT P
NC
OVLD-N
AMPOUT N
NC
!
CN103
! !
B6B-EH CN402 CN452
CDE9087 CDE9088
+OUTN 1
(CWH1515)
3
GNDS
NFBN 4
GNDS 5
CENTER N 6
B4B-EH
!
B GNDS
CN104
4
GNDS CN401
CDE9073
TR-E N 1
3 +OUTN
TR-C N 2
2 -OUTN
TR-B N 3
AKP1126 CDE9074 1 NFBN
CN101 4
B3B-EH CENTER N
2 +INPUT
1 1
GNDA 1 TR-E N
2
TR-C N
-INPUT
3
! 2
3 CN203 3 TR-B N
B6B-EH
GNDA CN491
+OUTP 1 CDE9077
-OUTP 2
KN102
GNDS
NFBP
3
4
GNDS POWER AMP UN
(CWH1516)
VNF1084
KN101
GNDS 5
GNDA CND5464 CENTER P 6
1
!
GNDA
GNDS CN451
GNDS 4 CDE9072
TR-E N 1 +OUTP
3
C TR-C N 2 -OUTP
2
TR-B N 3 NFBP
1
B4B-EH 4 CENTER P
CN204
! 1 TR-E N
CN102
2 TR-C N
CKS6112
V+55 3 TR-B N
1
GNDA GNDA CN492
2
CDE9076
V-55
3
T3(SUB TRANSFORMER)
CTT1161:(J)
! CTT1162:(U)
CTT1163:(Y5)
PRIMARY No.1 No.2
T1(MAIN TRANSFORMER)
CTT1158:(J)
No.3 CTT1159:(U)
CTT1160:(Y5)
D No.1 No.3
No.2 No.4
CND5464
CND5464
KN403
KN402
KN404
ACRY2
ACRY1
GNDP
1 1
! ! No.4
CDE9063 GNDA
+B
CN608 CN651
3
CKS6112 CKS6112
NEUTRAL
3
No.5
CDE9062
2 KN603
LIVE
1
! CND5464
T1L
1
! KN604
P-SE2 CND5464 No.2
3 No.6
! T1N
S1
! CDE9058 2 CN607
P-SE1 CKS6112
1
FU3
E
2
! 1 2
RY601 R601 !
CN611
CN612
No.1 No.3
CSH1076
1 2 T2L ! ! ! !
1
FU1
KN605
CDE9071 1 2 1 2 1 2 1 2
CND5464
KN606
KN351
CDE9070 1 1 CND5464
LIVE T1:NO.3
1
KN601 ! KN353
! CND5464
CN609
CN610
!
1
KN352 CND5464
KN602 V-B
! CND5464 CND5464
1
CWH1518:(U)
PRIMARY
CWH1519:(Y5) KN356
CWH1517
CND5306
CN652
T2:NO.3 ! VAC1B CDE9096 !
1
CDE9089
CN301 J301
GNDS No.2 No.6 RGAC1A CKS6111 CDE9059
7 V-55
1 V-55 3
+12V
-12V
REGULATOR
6
PRT LT
GNDS
RGAC2A
2
REGULATOR GNDA 2
F for
5
4
V-12U T2(MAIN TRANSFORMER)
UNIT V+55
CN351
1
V+55
GNDA
PRIMARY UNIT
PROTECTION
(CWH1520)
V+55
V-12
3 CTT1159:(U) 1 GNDA 1
GNDP RGAC2B ! !
(CWH1518: U) 2
V+12
CTT1160:(Y5) 2
CN302 CN303
2
CDE90
3
1 CKS6111 CKS6112
(CWH1519: Y5) VOLTAGE CHECK
10 TAD-M600
1 2 3 4
5 6 7 8
Q492
2SC4883A
PTFM04BD471Q2N34B0
!
TH490
1
2
! Q401
2SC3519A
OVLD+N
OVLD-N
AMPOUT N
GNDA
OVLD+P
OVLD-P
AMPOUT P
GNDA
POSI
GND
CN493
!
Q402
CDE9086 2SA1386A
! !
CN402 CN452 Q403
CDE9087 CDE9088 2SC3519A
CN504
CDE9090
! 1 V-12
Q405
2SC3519A 2 MUTE
3 GNDS
!
Q407
CN501
2SC3519A B4B-EH !
1 OVLD DCT+N
! 2 OVLD DCT-N
Q409
2SC3519A 3 AMPOUT N B
4 GNDA
!
Q411
CN502
2SC3519A B4B-EH !
1 OVLD DCT+P
! 2
Q404 OVLD DCT-P
2SA1386A 3 AMPOUT P
! 4 GNDA
Q406 CN503
2SA1386A B2B-EH
PROTECTION
1 POSI
!
Q408 2 GND
2SA1386A
H1516) Q412
2SA1386A
! 5
4
GNDS
V-12U
3 V-12V
!
Q462 2 GNDP
2SA1386A
1 V+12
! C
Q460 CN505
CDE9080
2SA1386A GNDS
9
OPE-B1
! 8
Q458 OPE+B1
2SA1386A 7
6 GNDS
!
5 OPE-A1
Q456
2SA1386A OPE+A1
4
! 3 GNDS
Q454
2 -12V-B2
2SA1386A KN594
KN591 KN592 KN593
1 PROTECT+B2 CND5464 CND5464 CDE9083 CDE9082
! 1 1 1 1
Q461
2SC3519A
!
Q459
2SC3519A
!
Q457
2SC3519A
CN701
B6B-EH
! OPE-B1
Q455
6
LED1 UNIT D
2SC3519A 5 OPE+B1
Q453
! 4 OPE-A1
(CWH1522)
3 OPE+A1
2SC3519A
2 -12V-B2 CKE1072
! 1 PROTECT+B2 +SP OUT A
1
Q451
CDE9084
CND5464
CND5464
CND5464
CDE9079
CDE9078
2SC3519A CN702
KN403
KN402
KN404
KN451
KN401
B4B-EH
! ! ! 1 PROTECTION
CKE1073
1 1 1 1 1 2SA1386A 2
Q452 CONT.-12V
-SP OUT A
1
3 OPERATION
CDE9063 GNDA
SP OUT N
SP OUT P
+B
-B
Q491
CDE9085
4 -12V
2SC4883A
CKE1072
CDE9062
CDE9069
+SP OUT B
1
CKE1073
CN701
V+B CDE9081
-SP OUT B
1
1
V+B V+B PROTECTION
2
CDE9060 CDE9061 CONT.-12V
C1 C3 3
OPERATION
E
+ +
! CCH1954 CCH1970 4
353 D354 -12V
30A20 KSH30A20
2 1 2
LED2 UNIT
2
KN353
(CWH1523)
GNDA
CND5464
V+B
1
KN354
CND5464
V-B
CDE9093
1
GNDA
C4
V-B
C2 CCH1970
06 + +
CDE9094 CCH1954
GNDA
06
CDE9096 ! - When ordering service parts, be sure to refer to "EXPLODED VIEWS and
J301
CDE9059
V-55 3
V-55 CDE9067 CDE9068
V-B
PARTS LIST" or "PCB PARTS LIST".
GNDA 2 V-B - The > mark found on some component parts indicates the importance of
V+55 1
V+55 F
CN351 the safety factor of the part.
GNDA
CDE9066
V+55
CKS6111
GNDA
GNDA 1
2
CDE9091 Therefore, when replacing, be sure to use parts of identical designation.
- : The power supply is shown with the marked box.
3
LTAGE CHECK
TAD-M600 11
5 6 7 8
F
E
B
A
D
C
12
VOLTAGE AMP UNIT POWER AMP UNIT PROTECTION UNIT
(CWH1515) (CWH1516) (CWH1521)
INPUT
2
1
1
1
3 PROTECTION RY
30dB 0dB SP OUTPUT
30dB 0dB
LED 1 UNIT
(CWH1522)
T1, T2
CTT1159: U
CTT1160: Y5
2
2
T1 LED 2 UNIT
3 1
(CWH1523)
C1: CCH1954
4.2 OVERALL BLOCK DIAGRAM
C2: CCH1970
C3: CCH1954
C4: CCH1970
PRIMARY UNIT
To POWER AMP +44V (CWH1518: U)
C1 C3 4
T1 No.4 5 (CWH1519: Y5)
TAD-M600
T2 No.3
C2 C4
To POWER AMP -44V FU1 CDX1013: U, Y5
33000uF×4 6 2 INLET
REGULATOR UNIT
AC RY SURGE KILLER
3
3
(CWH1520)
+55V T2 AC CABLE
POWER SW
3 1 CSH1076 ADG7061: U
To VOLTAGE AMP GND FU2
ADG7062: Y5
-55V
AC RY SURGE KILLER
4
5 FU3
6 2 T3
4
4
To PROTECTION +15V
To PROTECTION -15V
CTT1162: U
CTT1163: Y5
5 6 7 8
5. DIAGNOSIS
5.1 TROUBLESHOOTING
A
No power
C
Power line in contact Defective power transistors
with the chassis, or Defective rectifier at the output stage.
defective power diode(s). Defective bias circuit at the
electrolytic capacitor voltage AMP block.
(C1, C2, C3, C4).
D
The LED remains lit in red. The LED is lit in yellow.
The temperature of The SP cable at DC is output Disconnected Defective MUTE Defective line input
the heat sink is the output end is in because of defective connectors in RY Drive circuit in connector or loose
abnormally high. contact with the parts in the voltage the Protection the Protection block. line output connection.
Check if the vent is chassis. AMP block or short- block.
obstructed, etc. Check for over circuiting.
current. Check if DC is output.
Point to be checked
If any of or several
LEDs (D303-D308) Short-circuiting of D301
in the circuit are P-301 and P-302 and D302, defective
not lit, defective are open because of C301/C302, Q301/Q302,
part(s) or short- a defective regulator. C309/C310, etc. F
circuiting exists.
TAD-M600 13
5 6 7 8
1 2 3 4
TR-B N
TR-C N
TR-E N
GNDS
DC ADJ
CN104
4
B4B-EH
VR101
5K
2
270 1/4W
100k 1/4W
100 1/4W
AMRS
330 1/4W
330 1/4W
AMRS
R107
R119
R151
R115
R121
2.2/250
C121
R123 3
330 1/4W
Q115
2SA970(BL)
2SA970(BL)
2SA970(BL)
2SA970(BL)
Q125
Q113
Q105
2SA970(BL)
V+55 +55V
SLI-343URC
15k 1/2W
Q117
R109
100/50
D103
C111
10p 500V
R153
C115
C105
DM
Q119 ! 100p 125V
100 1/4W
2SC2240(BL)
2SC2240(BL)
10p 500V
Q111
DM
Q107
C107
Q103
2SC4883A(Y)
R103 IDOLE ADJ
2SC2240(BL)
1k 1/4W
100/50
1 330 1/4W
C109
Q109
100/50
R144
C114
HZ5CLL D105
HZ15-2L
D101
AMRS
2SA970(BL)
Q101
2 VR102
10k 1/4W
UKZ
200
R111
100 1/2W
R137
!
3
R127
R101 C125 C129 33k 1/4W
2.2k 1/4W
2.2/250
R113
C113
R131
0.47/250
47 1/4W
C117
C127 AMRS
C
2200p/125V R114
C101
R102
R124
220p/125V
AMCH
AMCH 47 1/4W
R129
AMRS
3.9k 1/4W
HZ4CLL
D106
R128
33k 1/4W
100 1/2W
R138
!
10k 1/4W
R112
R130
1k 1/4W
2SA970(BL)
R104
100 1/4W 2SC2240(BL)
Q110
100/50
C110
2SC2240(BL)
1k 1/4W
Q102
HZ15-2L
AMRS
D102
Q120 Q122
R118 ! 2SA1859A(Y)
2SC2705(OY)
10P 500V
2SA970(BL)
!
Q108
2SA970(BL)
Q104
R126
10k 1/4W
DM
Q112
R106
DM
C106
100p 125v
15k 1/2W
2SC2240(BL)
SLI-343URC
R110
100/50
AMCH
C112
D104
Q118
D -55V
2SC2240(BL)
2SC2240(BL)
2SC2240(BL)
Q126
Q106
Q114
Q116
2SC2240(BL)
100k 1/4W
220 1/4W
330 1/4W
330 1/4W
100 1/4W
AMRS
R108
R122
R152
AMRS
R116
R120
2.2/250
C122
47 1W 750 1W 750 1W
CM1 CM1 CM1
E
This circuit is a voltage amplifier stage of 30-dB gain. To improve the high-frequency characteristics, a cascode bootstrap
The input block (Q101, Q102, Q103, and Q104) is a buffer configuration (Q111, D101, Q112, and D102) at the initial stage
amplifier. A current mirror circuit has been adopted as a constant improves the high-frequency characteristics.
current circuit. Operating it on constant current reduces any
influence of temperature drift. A diamond buffer circuit is The negative feedback (NFB) is applied from the output stage to
constructed by cross-connecting this circuit and the initial stage of the β circuit that consists of R145, R146, and R147. When the
the amplifier section. feedback is applied to the emitter that is located at the initial stage
of the amplifier section, where the impedance is low, the NFB
The signal voltage attribute that is input to the initial stage (Q107, current flows and serves as the current feedback.
Q108, Q109, and Q110) of the amplifier section is converted to
current via the current mirror circuit (Q113 <=> Q115, Q114 <=> As described above, a high-accuracy circuit is adopted in each
Q116). A Wilson Mirror circuit has been adopted as a current mirror part, and a simple configuration is adopted in which the voltage
circuit, for higher accuracy. attribute is converted to current then reconverted to voltage in one
F
The V/I converted current attribute is converted to voltage with the stage. Combined with a current feedback configuration, all these
aid of the input impedance of the SEPP circuit at the output buffer features achieve a highly stable amplifier.
(Q121, Q122) then output.
14 TAD-M600
1 2 3 4
5 6 7 8
1
D401
FSF10A20 Q401 ! Q403 ! Q405 ! Q407 ! Q409 ! Q411
! 2SC3519A 2SC3519A 2SC3519A 2SC3519A 2SC3519A
2SC3519A
2
R405 R407 R409 R411 R413
R401 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W
! 10 1/2W ! ! ! ! !
120 1/2W 120 1/2W 120 1/2W 120 1/2W 120 1/2W
0.22 5W
0.22 5W
0.22 5W
0.22 5W
0.22 5W
R417
CN401 !
10 1W
R421
R403
R419
! !
R423
R425
!
1u/100
C407
CDE9073-A ! ! !
0.47/250V
+OUT N 1
C403
OUT B
-OUT N 2
CCN1271-A
NFB N 3
1u/100
10 1W
0.22 5W
0.22 5W
0.22 5W
C408
0.22 5W
R404
R426
R418
R420
R422
R424
Center N 4
! ! ! ! ! !
120 1/2W 120 1/2W 120 1/2W 120 1/2W 120 1/2W
R402 ! ! ! ! !
!
10 1/2W R406 R408 R410 R412 R414
4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W
Q402 Q404 Q406 Q408 Q410 Q412
1
C402
470p/125V
AMCH
This circuit amplifies power. A three-stage Darlington structure is All these allow driving of 600-W, 4-ohm output speakers without C
adopted, which includes the output SEPP at the voltage amplifier difficulty.
stage, driver stage (Q401, Q402), and final stage (Q403-Q412), This circuit belongs to the AB class, with total idle current of 0.5 A
which has 5-parallel push-pull composition. (a product with power output up to 2 W belongs to the A class).
REGULATOR UNIT
+55V
GND
-55V
This is a basic feedback-type constant-voltage circuit. To suppress the influence of power fluctuations, a current mirror F
The forward voltage (Vf) of the LEDs (D303, D305, D307 [D304, circuit (constant current circuit) that constituts of Q307-D309
D306, D308]) is used as the reference voltage, which is 5.4 V (1.8 (Q308-D310) is used. Adjust the output voltage (VR301, VR302) to
V × 3). ±55 V.
TAD-M600 15
5 6 7 8
1 2 3 4
A
PROTECTION UNIT
R545
2.2k
To PowerAMP A'ssy
R541
6.8k
CN503
B2B-EH
2SC2240(BL)
R542
22k
Q541
1
POSISTOR
2 R543
C541
NM
2SC2240(BL)
5.6k
Q542
R544
2.7k
B
0.022u/50
MTF
R553
C551
1.2k
1SS133
1SS133
D507
D527
R552
2SA970(BL)
2.2k
Q553
R513
100k
R533
100k
To PowerAMP A'ssy
2.2u 50V
1SS133
R551
4.7k
D503
C501
! CN501
B4B-EH
2SC2240(BL)
R501
560 1/4W
Q501
R554
1
4.7k
R510
OVLD DCT+N
470
AMRS
2 R508
2SC2240(BL)
OVLD DCT-N
R502 220k
R555
Q503
4.7k
3
2SC2240(BL)
AMP OUT N 560 1/4W
DTC143ES
AMRS
2SA970(BL)
Q551
R511
Q552
470
GNDA
Q502
33u/25
C503
2.2u 50V
R509
47k
0.01u/50
R556
R504
C552
1.2k
C502
R503
10k
R507
10k
2.2k
33u/25
C504
1SS133
1SS133
D502
1SS133
D504
D501
1SS133
1SS133
D559
D560
GNDA
2SA970(BL)
D562 1SS133
D561 1SS133
Q504
To PowerAMP A'ssy
1SS133
D523
2.2u 50V
CN502
C521
! B4B-EH R521
560 1/4W
2SC2240(BL)
AMRS
Q521
1
OVLD DCT+P
R530
470
2
2SC2240(BL)
3
AMP OUT P 560 1/4W
4 AMRS
2SA970(BL)
R531
GNDA
470
33u/25
Q522
2SC2240(BL)
C523
2.2u 50V
R529
D
47k
Q505
C522
R524
R523
R527
2.2k
10k
10k
33u/25
C524
D524
D522
D521
1SS133
1SS133
1SS133
C505
220p
R512
1.2k
2SA970(BL)
GNDA
Q524
R514
R534
100k
100k
V+12V
100u 25V
CN507
1SS133
1SS133
1SS133
1SS133
B7B-EH
1SS133
1SS133
D563
D564
D565
D566
D508
25V
D528
C532
V+12 1
100u
GND 2
V-12V
V-12 3
V-12U
V-12U 4
E
GNDS 5
PRT LT 6
GNDS 7
GNDS
GNDS GNDP
16 TAD-M600
1 2 3 4
5 6 7 8
1SS133
R572
D552
68k
1.0u/50
R563
4.7k
4.7k
R565
R570
10k
R567
C555
CN504
5.6k
Q563
2SA965(OY)
2SC2240(BL)
CDE9090-A
2SA970(BL)
R571
1SS133
Q564
120k
D553
2SC2240(BL)
V-12
Q557
1
DTC114ES
R558
Q558
56k
2 MUTE
2SA965(OY)
Q554
Q562
3 GNDS
R568
47
R569
1k
R559
R564
R575
5.6k
12k
820(1/2W)
R562
100
470(1/2W)
2SA970(BL)
470(1/2W)
R574
Q561
R573
2SC2240(BL)
Q559
R576
1 PROTECT +B2
27k
2SC2235(OY)
Q555
Q560
R557
R561
330k
4.7k
-12V -B2
R566
5.6k
2
2SC2240(BL)
220u 25V
C553
ACH1482-A
Q556
GNDS
2SC2235(OY)
3
R560
8.2k
ACH1480-A
HZ18L-1
D551
C554
HZ18L-1
OPRATION +A1
D554
100u 25V 4 C
5 -12V -A1
6 GNDS
7 OPRATION +B1
Q565
DTC143ES -12V -B1
DTC143ES
8
Q566
9 GNDS
R577
15k
CN505
CDE9080-A
R581
R583
22k
22k
C556 C557
MTF(CFTNA) MTF(CFTNA) C558 C559
2SC2240(BL)
Q581
C581
4.7u/50
3.9k
D555 D556
RY591 RY594
3 2 3 2
4 4
1
KN591 1 KN592 1
CND5464-A CND5464-A
RY592 RY595
3 2 3 2
CSR1033-A CSR1033-A
4 4
1 1
RY593 RY596 E
3 2 3 2
To SP- Terminal
To SP+ Terminal
CN593 CN594
4 CDE9082-A 4
4 CDE9083-A
1 1
CSR1033-A CSR1033-A
Temperature detection For more details on the protection functions, see the descriptions
If the temperature rises, the resistance value of the positive below.
thermistor (TH490) mounted on the heat sink also rises.
When the temperature reaches about 95 °C, Q541 is set to ON and
the illumination on the front panel turns red.
NOTE: Under such circumstances, the protection function is not
activated.) F
If the temperature continues to rise and exceeds about 100 °C,
Q542 is set to ON and the protection function is activated (speaker
relay: OFF, main power: OFF).
TAD-M600 17
5 6 7 8
1 2 3 4
A
Detailed Descriptions on the Protection Functions
Power-ON muting function
• When power is set to ON, signal muting is activated for about 8 seconds, resulting in no sound. While muting is activated,
the red LEDs are lit.
• After signal muting is released, the red LEDs go dark, the white LEDs light, and sound is output.
Temperature-detection function
• If there are continuous outputs larger than the upper limit expected from low-load output, or when the ambient temperature
is high, the temperature of the heat sink is detected and the protection function will be activated.
• The temperature-detection function is activated in two steps, as described below.
• In the first step, if the temperature exceeds a preset temperature (90-95 ºC), the white LEDs go dark and the red LEDs light
to warn that the internal temperature of the amplifier is abnormally high, but sound continues to be output.
• In the second step, if the temperature exceeds another preset temperature (a preset temperature of the first step plus about
D
100 ºC), the output is shut off and sound will not be output.
• If the first detection step is activated, lower the output level and the ambient temperature. If the red LEDs go dark and the
white LEDs light, the amplifier can be used normally afterwards.
• If the second detection step is activated, turn the unit off. Let it cool down for several dozen minutes and lower the ambient
temperature and the amplifier output level before turning it back on again.
18 TAD-M600
1 2 3 4
5 6 7 8
Overload-detection operation
• The overload status (approx. 0.5 ohm or less) on the + side is detected at Q501 and Q521, and that on the - side is detected
at Q502 and Q522. Detection of an abnormality is retained via the latch circuit that consists of Q552 and Q553.
Then Q554 together with Q555 is set to ON, C553 is rapidly discharged, the subsequent differential circuit and output/input
relays at the relay drive circuit are activated, then signals are set to OFF.
• The white LEDs go dark when Q563 is set to OFF, and the red LEDs light when Q564 is set to ON.
• To prevent arc discharge when the output relay is set to OFF, approx. 4-ms time-constant circuits are provided with the C555
and R565 circuits so that the output relay is activated later than the input relay.
C
Temperature-detection operation D
• For temperature detection, use a TH490=PTFM04BD471Q2N34B0 (100 ºC) type Posistor from Murata Manufacturing that
can be secured to the heat sink with screws. The characteristics of this thermistor are as follows: at 80 ºC, typical 100 ohms
or less; at 90 ºC, 330 ohms or less (typ. 100 ohms); at 100 ºC, 470 ohms or higher (typ. approx. 1.5 k-ohms).
• In the first detection step, when the resistance value at the Posistor becomes 400 ohms or higher at a preset temperature of
90-95 ºC, Q541 is set to ON, Q565 is set to OFF, and the white LEDs go dark. Instead, Q564 is set to ON and the red LEDs
light.
• In the second detection step, when the resistance value at the Posistor becomes 1.4 k-ohms or higher at a preset
temperature of approx. 100 ºC, Q542 is set to ON. Detection of the abnormality is retained via the latch circuit that consists
of Q552 and Q553. The same operations as those for overload detection will then follow.
• If the first detection step is activated, lower the output level and the ambient temperature. Q541 will be turned OFF, the red
LEDs will go dark, and the white LEDs will light.
E
6. SERVICE MODE F
TAD-M600 19
5 6 7 8
1 2 3 4
7. DISASSEMBLY
A
Note:
Even if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures
described here are common.
• Be careful not to scratch or stain the cabinet during servicing, because it may cause a serious complaint.
• As the product weighs 90 kg, be fully careful when handling it. Four people are required when moving it.
• Be careful of the order of wire arrangement at a place where several wires are secured together with a screw (on the power
main electrolytic capacitor, etc.), as this can affect the sound quality. Follow the detailed procedure described in this section.
• As the product has conical feet, be very careful not to scratch floor surfaces in the customer’ s home.
B Disassembly
[1] Exterior Section
[1-1] Panel (Rear)
(1) Remove the nine screws. (BMZ40P140FCC)
(2) Remove the panel.
(3) Release the jumper wires, as required.
Panel
C
2
1 ×9
D
1 ×4
1 ×4
20 TAD-M600
1 2 3 4
5 6 7 8
A
[1-3] Panel section (Front and side)
(1) Remove the eight screws. (CBA2255)
(2) Remove the panel section. Panel section
(3) Release the jumper wires, as required. 1 ×8
T2
C4 T1
C3
C2
C1
• Rear view
• Rear view
TAD-M600 21
5 6 7 8
1 2 3 4
A
[2] Bottom Section
[2-1] Covers
2 1 ×6
(1) Remove the 40 screws. (PMB40P080FCC) 1 ×8 Cover
(2) Remove the all covers.
(3) Release the jumper wires, as required. Cover
1 ×6
1 ×12
1 ×8
Cover
B
Cover Cover
• Bottom view
PROTECTION
Unit
REGULATOR
Unit
PRIMARY T3
Unit
• Bottom view
22 TAD-M600
1 2 3 4
5 6 7 8
A
Disassembly of PCB Assemblies
Note: In the following disassembly procedures, the PANEL Assy (including the rear panel) and all the bottom covers are
assumed to have been removed.
CN102
CN181
1 1
• Rear view
(3) Remove the two screws that secure the Plate VOLTAGE AMP Unit
brackets (CND5327 and CND5328) to the
chassis and remove the VOLTAGE AMP Unit
together with the plate.
3 3
E
(4) Remove the 11 screws then remove the
VOLTAGE AMP Unit from the plate. VOLTAGE AMP Unit
4 4
4 4
4 4
4
F
4 4
4 4
TAD-M600 23
5 6 7 8
1 2 3 4
A
POWER AMP Unit
(1) Remove the VOLTAGE AMP Unit together with POWER AMP Unit
the plate. (See “g VOLTAGE AMP Unit”.)
(2) Remove the three screws for the KN402,
KN403, and KN404 then remove the cords
(CDE9062, CDE9063, and CDE9069).
2 KN403
2 KN402
KN404
2
B
• Rear view
(3) Remove the CN501, CN502, and CN503 from PROTECTION Unit
C
the PROTECTION Unit.
(4) Remove the two screws for the KN591 and
KN592 from the PROTECTION unit then
remove the cords (CDE9078 and CDE9079). CN503
3
4 KN592 CN502
3
(5) Remove the eight screws then remove the
heatsink from chassis. 4 KN591
CN501
3
5 5
5 5
D
5 5
5 5
• Bottom view Heatsink
(6) Remove the 27 screws from the all soldered POWER AMP Unit Heatsink
power transistors (Q401 to Q412, Q451 to
E Q462, Q491 and Q492) and the posistor 6 ×14
(TH490).
(7) Remove the six screws then remove the
POWER AMP Unit from the heatsink. Q491 Q492
Q401 Q403 Q405 Q407 Q409 Q411 Q461 Q459 Q457 Q455 Q453 Q451
Note on reassembly: 7 7 7
When reassembling, align the sheets (CNN3122)
squarely beneath the transistors.
7 7 7
Q402 Q404 Q406 Q408 Q410 Q412 Q462 Q460 Q458 Q456 Q454 Q452 TH490
6 ×13
24 TAD-M600
1 2 3 4
5 6 7 8
A
REGULATOR Unit
(1) Remove the VOLTAGE AMP unit together with
the plate. (See “g VOLTAGE AMP Unit”.)
(2) Remove the CN301, CN302, and CN351.
(3) Remove the six screws for the KN351 to
KN356 then remove the cords connected.
(4) Remove the six screws then remove the
REGULATOR Unit together with the plate.
4 2 4
4 CN302
KN353 B
CN301 KN354
2 KN356
2 KN355 KN352
CN351
KN351
4
4 3 ×6 4
• Bottom view
REGULATOR Unit
6 6 6
REGULATOR Unit
Upper
KN356 (from capacitor)
Tighten two cables
together.
KN355
A
PROTECTION Unit
(1) Remove the CN501, CN502, CN503, and
CN507. PROTECTION Unit
(2) Remove the two screws for the KN591 and
KN592 then remove the cords (CDE9078 and
CDE9079).
KN592
CN503
CN502
2 ×2 CN507 1 ×3
KN591 1 CN501
• Bottom view
(3) Remove the CN701 from the LED1 Unit. LED1 Unit
3 CN701
• Rear view
(4) Remove the eight screws then remove the PROTECTION Unit
PROTECTION Unit.
4 4 4 4
4 4 4 4
• Bottom view
26 TAD-M600
1 2 3 4
5 6 7 8
A
Note of the wiring
• Before reassembling the PROTECTION Unit, the inlet must be attached.
• When mounting the PROTECTION Unit, incline it so that it will not come into contact with the cables from the inlet.
OK
Inlet NG CN505
C
TAD-M600 27
5 6 7 8
1 2 3 4
A
Inlet wiring
Cord clamper
Secure the cables so that they will not move
C from side to side in the cord clamper. Binder
SP-B–
Rear panel
D
SP-A+
SP-B–
Rear panel
Tighten two cables
together.
Upper Upper
28 TAD-M600
1 2 3 4
5 6 7 8
A
PRIMARY Unit
(1) Remove the CN607, CN608, and CN651.
(2) Remove the six screws for the KN601 to
KN606 then remove the cords connected.
CN651 1 KN601
CN608 1
CN607
KN605 KN604
CN507 3
C
• Bottom view
4 4 4 4
Binder
• Bundle the 3 cables from the CN611, CN612,
and CN608.
• Secure the bundled cables at the base of the
CN608.
• Place the bundled cables apart from the fuse.
A
LED1 Unit and LDE2 Unit
(1) Remove the front panel. LED1 Unit Bracket LED2 Unit
(2) Remove the eight screws then remove the
bracket (CND5312).
2 2
2 2
2 2
2 2
• Rear view
(3) Remove the four screws then remove the LED1 Unit LED2 Unit
LED1 and LED2 Units.
3 3
3 3
• Rear view
30 TAD-M600
1 2 3 4
5 6 7 8
A
Transformers
(1) Remove the four screws for the KN603,
REGULATOR Unit
KN604, KN605 and KN606 from the
PRIMARY Unit then remove the primary lead
wires for the transformer.
(2) Remove the four screws for the KN351, 3
KN352, KN355, and KN356 from the
CN302
REGULATOR Unit then remove the CN301
secondary lead wires for the transformer. 3 KN356 2 2
(3) Remove the CN301 and CN302 from the KN355
KN352
1 1 1 1
KN605 KN606 KN604 KN603
D
T1 T2
4 4 4 4 4 4
5 5 5 5
Trans base Trans base
TAD-M600 31
5 6 7 8
1 2 3 4
A
Capacitors
(1) Remove the REGULATOR Unit together with
the plate. (See “g REGULATOR Unit”.)
(2) Remove the two screws from the positive
electrode of C2 and the negative electrode
of C3 then remove the lead wires.
(3) Remove the screw then remove the cords CDE9066 CDE9063
(CDE9063 and CDE9066).
2 3 2
B
− + − + − + − +
C4 C3 C2 C1
• Bottom view
C1 C2 C3 C4
4 4 4 4
C2 +
Screw
E
Washer
→ KN403 (CDE9062)
Stud
Tighten three cables Tighten three cables → C1 + (CDE9061)
together. together. → KN353 (CDE9060)
C3 –
Screw
Washer
F
→ KN404 (CDE9069)
− + − + − + − + Stud
C4 C3 C2 C1
→ C4 – (CDE9068)
• Bottom view → KN354 (CDE9067)
32 TAD-M600
1 2 3 4
5 6 7 8
A
Assembling of The Panel Section
[1] Top Section
Place the 4 brackets (CND5455) on the panel
(CNS9980) and secure them using the 8 screws
(PMB40P080FCC).
(Tighten the screws loosely so that the brackets
can move slightly.) Bracket Screw
Screw Panel
B
Bracket Screw
Screw Screw
Bracket
Screw
Screw
Bracket
Screw C
Screw
E
Screw
Screw
Screw
Make sure that the screw
is near the center of the
counter boring.
TAD-M600 33
5 6 7 8
1 2 3 4
A
After aligning the front edges of the panels,
tighten the 4 screws (PMB40P080FCC) securely
(final tightening) while pushing the brackets Final tightening
outward.
Align the front edges of the panels. Loosen then retighten the screws.
E
Panel (CNS9979)
34 TAD-M600
1 2 3 4
5 6 7 8
A
[3] Front Section
Place the panel (CNS9976). Make sure that there
is no unevenness or gap between panels in each
surface.
Panel
Check alignment at the bottom surface.
Before attaching this panel assy to the main unit (chassis,) the top panel must be detached.
Procedure
1 Detach the top panel then mount the U-shaped panel assy on the main unit.
2 Temporarily secure the rear panel.
3 Secure the panel assy to the main unit, using the screws.
4 Secure the top panel again.
5 Secure the rear panel (final tightening).
TAD-M600 35
5 6 7 8
1 2 3 4
(2) Turn on the unit with no load and no signal input. VR202 VR102
Amp- Amp+
(3) Adjust the VR101 and VR102 semifixed resistors for DC Idle Idle
adjustment adjustment
offset adjustment so that the DC offset voltages for
B AMP+ and AMP- become 0 mV ± 20 mV.
(4) Adjust the VR102 and VR202 semifixed resistors for idle Min Max
current adjustment so that the voltages at the end of the
emitter resistor for AMP+ and AMP- become VOLTAGE AMP UNIT
11 mV ± 3 mV.
(5) Let the unit sit for 30 minutes under windless conditions.
(6) Adjust the VR102 and VR202 semifixed resistors for idle [Measurement Points]
current adjustment so that the voltages at the end of the
emitter resistor for AMP+ and AMP- become POWER AMP UNIT
C 15 mV ± 3 mV.
36 TAD-M600
1 2 3 4
5 6 7 8
TAD-M600 37
5 6 7 8
1 2 3 4
- For the applying amount of lubricants or glue, follow the instructions in this manual.
38 TAD-M600
1 2 3 4
5 6 7 8
31 Label CAN6233
32 Sheet CHV1006
33 Sheet CHV1007
TAD-M600 39
5 6 7 8
1 2 3 4
Y5 Only
VOLTAGE AMP
CN101
PROTECTION
CN593
PROTECTION
CN594
Refer to
“9.5 PANEL SECTION”.
F
Refer to
“9.3 CHASSIS SECTION”.
40 TAD-M600
1 2 3 4
5 6 7 8
TAD-M600 41
5 6 7 8
1 2 3 4
C3
C4 C2 C1
TH490
Q404 Q408 Q412 Q460 Q456 Q452
Q402 Q406 Q410 Q462 Q458 Q454
Bottom view
C2 (+) terminal
VOLTAGE AMP
CN104
PROTECTION Plate
KN592
VOLTAGE AMP PROTECTION C3 (−) terminal
CN103 KN591
C PROTECTION
CN502
VOLTAGE AMP
CN204
VOLTAGE AMP
CN203
PROTECTION PROTECTION
CN503 CN501
for T1 for T2
POWER AMP
CN491
D POWER AMP to Plate
CN401
Socket (3P)
PROTECTION
CN504
POWER AMP
CN492
POWER AMP
CN451
REGULATOR
CN304
T1: REGULATOR
CN301, KN351, KN355
T2: REGULATOR
CN302, KN352, KN356
T1: PRIMARY
KN603, KN604
T2: PRIMARY
E KN605, KN606
Refer to
“9.4 BOTTOM SECTION”.
42 TAD-M600
1 2 3 4
5 6 7 8
TAD-M600 43
5 6 7 8
1 2 3 4
A • Bottom view
PRIMARY
CN607
PRIMARY
CN652
Main trans LED1
Main trans CN701
(T1) (T2)
to Plate POWER AMP
SP Out KN451
C C3 (−) terminal
C2 (+) terminal
to Plate POWER AMP
CN493
POWER AMP
CN452
POWER AMP VOLTAGE AMP
KN401 CN181 POWER AMP
CN402
Main trans
(T2)
Main trans
(T1)
Sub trans
D (T3)
PROTECTION
CN507 AC Inlet
Sub trans
(T3)
Main trans
(T2)
Main trans
(T1)
PRIMARY
CN651
F
PRIMARY
CN608
44 TAD-M600
1 2 3 4
5 6 7 8
31 Washer WS40PKI
* 32 Label CAN6432
33 Regulator Assy CWX3808
TAD-M600 45
5 6 7 8
1 2 3 4
PROTECTION
CN505
46 TAD-M600
1 2 3 4
5 6 7 8
6 Bracket CND5452
7 Bracket CND5453
8 Bracket CND5454
9 Cushion CNN3071
10 Cushion CNN3214
B
11 Cushion CNN3215
12 Panel CNS9976
13 Panel CNS9977
14 Panel CNS9978
15 Panel CNS9979
21 Screw PMB40P080FCC
22 Screw PMH30P060FCC
23 Screw PMH40P180FCC
TAD-M600 47
5 6 7 8
F
E
B
A
D
C
48
1
1
TO EATH PLATE
FROM 3P CANON
CN181
CN101
KN101
KN102
TO CHASSIS GND
B2B-EH
B3B-EH
TO PROTECTION ASSY
CND5464
-INPUT
V-12
VNF1084-A
+INPUT
GNDA
MUTE
2
3
2
1
1
1
1
C182 C181
1/50 1/50
V-12
D181
1SS133
D182
1SS133
L+ 1 10 L-
1A 2 9 2A
1COM 3 8 2COM
7
10.1 VOLTAGE AMP UNIT
1B 4 ZB
NC1 5 6 NC2
1 R201
AMRS
AMRS
330 1/4W
330 1/4W
1
R101 1
2
2
RY181
R202 CSR1031-A R102
220k 1/4W 220k 1/4W
1
AMRS AMRS
100/50
C225
C125
100/50
1
GNDA
R224
10. SCHEMATIC DIAGRAM
C229
C129
AMRS AMRS
100/50
100/50
220k 1/4W
1
1
1
1
TAD-M600
Q226 Q225 Q126 Q125
R110
1k 1/4W
1k 1/4W
1k 1/4W
1k 1/4W
R204
1 R203
R104
R103
AMRS
AMRS
15k 1/2W
AMRS
AMRS
330 1/4W 2SC2240(BL) 15k 1/2W 330 1/4W 330 1/4W 2SC2240(BL) 15k 1/2W 330 1/4W
R206 Q202 R205 R106 Q102 R105
10k 1/4W Q201 10k 1/4W 10k 1/4W Q101 10k 1/4W
2SA970(BL) 2SA970(BL)
C227
C127
AMCH
AMCH
2200p/125V
2200p/125V
330 1/4W Q206 2SC2240(BL) 2SA970(BL) Q205 330 1/4W 330 1/4W Q106 2SC2240(BL) 2SA970(BL) Q105 330 1/4W
3
3
R254 100 1/4W 100 1/4W R154 100 1/4W 100 1/4W
2SC2240(BL) 2SA970(BL) 2SC2240(BL) 2SA970(BL)
R212 R211 R112 R111
1
1
Q208 Q207 R253 Q108 Q107 R153
2SA970(BL) 10k 1/4W 10k 1/4W 2SC2240(BL) 2SA970(BL) 10k 1/4W 10k 1/4W 2SC2240(BL)
1
1
1
1
CM1
R247
Q211 Q213
R147
Q111 Q113
47 1W
47 1W
R216 2SC2240(BL) 2SA970(BL) 2SC2240(BL) 2SA970(BL) R215 R116 2SC2240(BL) 2SA970(BL) 2SC2240(BL) 2SA970(BL) R115
1
220 1/4W Q210 Q209 270 1/4W 220 1/4W Q110 Q109 270 1/4W
1
R213
R113
R214 1
R114 1
AMRS
AMRS
AMRS
AMRS
47 1/4W
47 1/4W
47 1/4W
47 1/4W
R223 3 1 R123 3 1
R217
R117
R218
R118
DC ADJ
DC ADJ
100 1/4W
100 1/4W
2 2
100 1/4W
100 1/4W
VR201 VR101
5K 5K
1
1
1
1
1
1
1
1
R246
CM1
CM1
Q216
Q116
750 1W
750 1W
1
1
1
1
1
1
2SA970(BL)
2SA970(BL)
Q215
Q115
DM DM DM DM
2SC2240(BL)
2SC2240(BL)
100 1/4W Q218 2.2/250 Q217 100 1/4W 100 1/4W Q118 2.2/250 Q117 100 1/4W
AMRS 2SC2240(BL) 2SA970(BL) AMRS AMRS 2SC2240(BL) 2SA970(BL) AMRS
1 R245
R145
CM1
Q220
Q120
Q219
Q119
750 1W
750 1W
33k 1/4W
R226
R225
R126
R125
33k 1/4W
R228
33k 1/4W
33k 1/4W
AMRS
D204 D104
R128
4
100 1/4W
100 1/4W
100 1/4W
100 1/4W
2SA1145(OY)
2SA1145(OY)
4
2SC2705(OY)
2SC2705(OY)
D203 D103
R227
R127
D205 D105
R229 R129
IDOLE ADJ
HZ5CLL HZ5CLL
IDOLE ADJ
GNDS
220
HZ4CLL HZ4CLL
220
22
22
5 6 7 8
A
TR-B N
TR-C N
TR-E N
TO POWER AMP ASSY
GNDS
VOLTAGE AMP UNIT
(CWH1515)
CN104
1
4
B4B-EH
V+55 CN102
B03P-NV
1 V+55A
1 TO REGULATOR ASSY
C115
470/63
C119
! 100p 125V
2 GNDA
R133 3 V-55A
220 1/2W AMCH
!
Q121
2SC4883A(Y)
470/63
C120
1 330 1/4W
DOLE ADJ
R144
D105
UKZ
2 VR102
200
HZ5CLL
B
100 1/2W
R137
!
3
CN103
2.2k 1/4W
B6B-EH
R131
1 +OUT N
C117
2 -OUT N
GNDS
3.9k 1/4W
3
GNDS
R129
HZ4CLL
4 NFB N
D106
100 1/2W
5 GNDS
R138
!
6 CENTER N
1k 1/4W
R130
GNDS
!
!
R134 JH101 JH102
Q122
220 1/2W 2SA1859A(Y) VEF1040-A VEF1040-A
C116
100p 125v
AMCH
1
C
JH201 JH202
VEF1040-A VEF1040-A
TR-B P
TR-C P
TR-E P
CN204
GNDS
B4B-EH
TO POWER AMP ASSY
1
1 C215
! 100p 125V
R233 !
220 1/2W AMCH Q221
2SC4883A(Y)
1 330 1/4W
DOLE ADJ
R244
2 VR202
D205
200
HZ5CLL
100 1/2W
R237
!
GNDS
3
2.2k 1/4W
CN203
B6B-EH
R231
1
C217
2 -OUT P E
GNDS
3.9k 1/4W
3
R229
HZ4CLL
4 NFB P
D206
100 1/2W
5 GNDS
R238
! 6 CENTER P
1k 1/4W
R230
GNDS
!
!
R234
Q222
220 1/2W 2SA1859A(Y)
C216
The ! mark found on some component parts should be replaced with same parts (safety regulation authorized)
100p 125v
AMCH of identical designation.
1
V-55A
TAD-M600 49
5 6 7 8
1 2 3 4
TR-E N 1 Q491
2SC4883A(Y)
From Voltage Amp TR-C N 2
3
TR-B N
CN493 !
CDE9086-A
1
From Protection Posistor TH490
2 PTFM04BD471Q2N34B0
C401
470p/125V
1 AMCH
1
D401
FSF10A20 Q401 ! Q403 ! Q405 ! Q407 ! Q409 !
2 !
2SC3519A 2SC3519A 2SC3519A 2SC3519A 2SC3519A
B
2
R405 R407 R409 R411 R413
R401 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W
! 10 1/2W ! !
! ! !
! ! !
10 1W
R403
R417
R419
R421
R423
R425
0.22 5W
0.22 5W
0.22 5W
0.22 5W
CN401 !
1u/100
C407
CDE9073-A ! ! !
1
0.47/250V
+OUT N 1
C403
-OUT N 2
From Voltage Amp
NFB N
CCN1271-A
0.22 5W
1u/100
0.22 5W
0.22 5W
3
C408
10 1W
R404
R418
R420
R422
R424
R426
Center N 4
! ! ! !
1 ! !
C !
R402
10 1/2W
! ! ! ! !
R406 R408 R410 R412 R414
1 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W
Q402 Q404 Q406 Q408 Q410
1
C402
470p/125V
AMCH
C451
470p/125V
1 AMCH
1
R467
R469
R471
R473
R475
0.22 5W
0.22 5W
0.22 5W
0.22 5W
! ! ! ! ! !
1u/100
CN451
C457
1 !
CDE9072-A
0.47/250V
1
+OUT P
C453
1
-OUT P 2
From Voltage Amp
NFB P
0.22 5W
1u/100
0.22 5W
0.22 5W
C458
0.22 5W
3
10 1W
R454
R468
R470
R472
R474
R476
Center P 4
! ! ! ! ! !
1
R452
! ! !
! !
10 1/2W
R456 R458 R460 R462 R464
1 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W 4.7 1/2W
Q452 Q454 Q456 Q458 Q460
1
C452
470p/125V
AMCH
C492
!
CN492 1200p
1 CDE9076-A
F
TR-E P 1 Q492
2SC4883A(Y)
From Voltage Amp TR-C P 2
3
TR-B P
50 TAD-M600
1 2 3 4
5 6 7 8
KN403
+B
1
CND5464-A To Capaciter Block
! Q409 ! Q411
2SC3519A 2SC3519A
R413
B
!
4.7 1/2W OVLD DCT+
1 CN402
!
CND9087-A
2 OVLD DCT- To Protection
R435 R437 3
AMP Output N
120 1/2W 120 1/2W 4
GNDA
470/63 KZ
AMCG
1/250V
R423
R425
C410
C413
0.22 5W
0.22 5W
! !
0.22 5W
R424
R426
470/63 KZ
! !
AMCG
1/250V
C411
C414
R436 R438
1
CND5464-A -B To Capaciter Block
C404
0.47u
C405
0.47u
4.7 5W
R441
KN402 GNDA
1
Q459 Q461
D
! 2SC3519A ! 2SC3519A
R463
4.7 1/2W
!
1
OVLD DCT+
R485 R487
!
2 CN452 OVLD DCT-
120 1/2W 120 1/2W
3
CDE9088-A Test Point
AMP Output P
4
R473
R475
GNDA
0.22 5W
0.22 5W
! !
R476
! !
R486 R488
The ! mark found on some component parts should be replaced with same parts (safety regulation authorized)
of identical designation.
F
TAD-M600 51
5 6 7 8
1 2 3 4
1 2
C610
0.01u
11EQS10 11EQS10
6
D601
C606
1u/50
ACG7039-A
CSR1032-A
RY601
11EQS10 11EQS10
6
4
D602
D603
C607
C611
1u/50
1u/50
CSR1032-A
1
RY602
!
D604
C612
1u/50
1
3
!
3
AKR7004-A
H601 H602
B 1 1
AKR7004-A
C601
0.01u
!
1 FU1
AC RY SURGE RY
C605 !
0.01u
R602
CCN1269-A
ACG7039-A
1 2
C613
0.01u
6
11EQS10 11EQS10
6
1u/50
D605
C608
CSR1032-A
C
AC IN
RY603
11EQS10 11EQS10
6
4
D606
D607
C609
C614
1u/50
1u/50
1
CSR1032-A
!
RY604
1
D608
C615
1u/50
From AC IN(L)
3
CND5464-A
AKR7004-A
!
3
H603 H604
KN601
1 1
AKR7004-A
C602
1 FU2
0.01u
!
CND5464-A
KN602
From AC IN(N)
D
/U: CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. SHV1410AN4
MFD. BY SOC FOR FU1, FU2 AND TYPE NO. 233001 MFD.
REG For PROTECTION
BY LITTELFUSE INC. FOR FU3.
! R652
D654 270
CN610 CN609 CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. 1SS133 (1/2W)
HZ12L-A2
1 1 REPLACE ONLY WITH SAME TYPE NO. 49101.6 MFD. BY
LITTELFUSE INC. FOR P651, P652.
C661
10u/50
CDE9071-A CDE9070-A
D656
C662
0.01u/50
! D655
1SS133
! D651
CN612 1 1C N 6 1 1
D3SBA20
IC651
to Power SW ! NJM7812
CN607
B03P-NV
! HEATSIN
E 1 2 3 4
! OU
1
CN608 CN651 ! 1 IN
B03P-NV Sub TRANS B03P-NV
GND
2200u/25
0.01u/50
P651
0.01u/50
R654
C653
C655
2
22k
AKR7005-A 1.6A/125V
H605 H606 Live
C651
1 1 1 ACRY1 1 1 2
C603 GNDP
1 FU3 0.01u
ACG7039-A
2 GNDRY 2
P652
3 ACRY2 3 1 2
0.01u/50
2200u/25
0.01u/50
C652
C654
R655
Neutral
C656
1.6A/125V
22k
1
! 2 COMMO
IN
! OU
The mark found on some component parts should be replaced with same parts (safety regulation authorized)
HEATSIN
of identical designation.
CWH1518- U FU3
CEK1374-A REK1142-A /U: 1A 125V D685 NM
CWH1519- Y5 CEK1378-A AEK1052-A /Y5: T630mAL 250V
52 TAD-M600
1 2 3 4
5 6 7 8
PRIMARY UNIT A
(CWH1518: U)
(CWH1519: Y5)
C611
1u/50
C612
1u/50
KN603
CND5464-A
To + Power Trans(L)
B
1
1
KN604
CND5464-A
To + Power Trans(N)
KN605
CND5464-A
To - Power Trans(L)
1
1
AC RY DRV SURGE RY DRV KN606
CND5464-A C
To - Power Trans(N)
2SC2240(BL)
C614
1u/50
2SC2240(BL)
R681
R682
R686
22k
12k
56k
Q684
Q682
2SC2235(OY)
2SC2235(OY)
D682 D683
Q683
Q685
1SS133 HZ18L-1
Q681
2SC2240(BL)
ACH1478-A
47u 25V
(KY 5x11)
R684
R685
R687
R690
R691
C682
100k
330k
100k
NP
10k
10k
R683
C681
8.2k
1u/50
or PROTECTION
R652
270
1/2W)
HZ12L-A2
D656
R653
C662
0.01u/50
4.7k
D684 To Protection
NM
IC651 CN652
! NJM7812FA
CDE9089-A
IC-3030-STL
HEATSINK
7
GNDS
OUT
E
PRT LT
220p/50
1 IN 6
3
C683
GND GNDS
5
11EQS10
0.01u/50
0.01u/50
V-12U
R654
D652
C655
C657
33u/25
C659
2
22k
4 V-12U
3 V-12V
2 GND
V+12V
11EQS10
1 V+12V
D653
R651
0.01u/50
0.01u/50
33u/25
C660
2.2k
R655
C656
C658
22k
1 GNDS
2 COMMON 3
IN
OUT V-12V
HEATSINK
! IC652
NJM7912FA F
IC-3030-STL
D685 NM
TAD-M600 53
5 6 7 8
1 2 3 4
SLI-343URC
A
!
Q301
V+UNREG 2SC2240(BL) 2SC4883A(Y)
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. 491010 MFD. BY R313
C311
R309
Q303
100/25
220p 100V
D309
560 1/4W
LITTELFUSE INC. FOR P301, P302.
4.7k 1/4W
C305
47k 1/2W F%
R303
330 1/4W
R301
! D301
Q307
2SA970(BL)
FCH20A20 Q309
CCH1956-A
2SC2240(BL)
47k 1/2W
4700/80
Q305
C301
2200/63
R315
2SC2240(BL)
C309
!
D303
B 1 2 3
1
A1
A2
K
P301
2
From Power Transformer
VR301
VAC3
120k 1/4W
SLI-343URC
CN301 2 1
1K
100/25
R311
B02P-NV
3
C303
5.1k 1/2W F%
!
D305
10 1/2W
R305
10A/125V R321
T1 NO5 1
VAC1 !
D307
T1 NO6 2
GNDA
D302
T2 NO5 FRH20A20
D308
1
5.1k 1/2W F%
C321
1/250
T2 NO6 2
SLI-343URC
R306
VAC2
120k 1/4W
100/25
D306
R312
C304
CN302
! P302
VR302
B02P-NV 1 2 3
3
C
K1
K2
1k
2 1
A
VAC4
CCH1956-A
2
!
D304
47k 1/2W
4700/80
!
1
10A/125V
R316
C302
2200/63
C310
2SC2240(BL)
Q306
2SA970(BL) 2SC2240(BL)
Q310
Q308
47k 1/2W F%
330 1/4W
R302
R304
220p 100V
R314
4.7k 1/4W
560 1/4W
C306
D310
100/25
C312
R310
Q304
2SA1859A(Y)
!
From Power Transformer
KN355
CND5464-A
GND1
1
T1 NO4
! KSH30A20
!
KSH30A20
KN356 D351 D352
CND5464-A
GND2
1
T2 NO3
1 2 1 2
1
T1 NO3
10 1/2W
R353
KN352 !
CND5464-A
! !
1
T2 NO4 KSH30A20
VAC6 KSH30A20 D354
D353
C351
1/250
1 2
1 2
1
2
1
V-B
54 TAD-M600
1 2 3 4
5 6 7 8
REGULATOR UNIT A
(CWH1520)
883A(Y)
V+55
13
47k 1/2W F%
CN303
R303
B03P-NV
!
1 V+55
BL) 2 VOLTAGE CHECK POINT
GNDA
2200/63
C309
3 V-55
B
1
2
VR301
3
5.1k 1/2W F%
CN304
R305
CDE9059-A
!
1 V+55
2 GNDA
3 V-55
5.1k 1/2W F%
R306
VR302
C
1k
2
1
2200/63
C310
BL)
47k 1/2W F%
R304
W
V-55
859A(Y) D
R351
to Capaciter Block
47k 1/2W
1 GNDA
2 NC
SH30A20 R355
B02P-NV
D352
47k 1/2W
CN351 !
KN353
1 2
CND5464-A
to Capacitor Block
2
E
1
V+B +
V+B
The ! mark found on some component parts should be replaced with same parts (safety regulation authorized)
of identical designation.
SH30A20 KN354
D354
CND5464-A
V-B
-
to Capacitor Block
1
1 2
2
V-B
TAD-M600 55
5 6 7 8
F
E
B
A
D
C
56
PRT LT
!
POSISTOR
V-12U
V-12
!
AMP OUT P
V+12
AMP OUT N
GNDS
GNDS
GND
OVLD DCT-P
OVLD DCT-N
OVLD DCT+P
OVLD DCT+N
GNDA
GNDA
2
7
6
5
4
3
2
1
1
CN507
B7B-EH
CN503
B2B-EH
1
1
2
2
4
3
4
3
1
1
To PowerAMP A'ssy
CN502
B4B-EH
B4B-EH
CN501
To PowerAMP A'ssy
GNDS
To PowerAMP A'ssy
AMRS
AMRS
C541
R502
560 1/4W
R501
560 1/4W
560 1/4W
AMRS
R522
R521
560 1/4W
AMRS
C531
GNDA
GNDA
NM
GNDP
100u 25V R531 R530 R511 R510 C501
C522 470 470 C521 C502 470 470 2.2u 50V
V+12V
2.2u 50V 2.2u 50V 2.2u 50V
C532
D522 R524
1SS133 10k
100u 25V
D521 R523 D502 R504
1
10.5 PROTECTION UNIT
1
D508
1
1
1SS133 R514 R513 D507
1SS133 R541
V-12U
GNDS
2
100k 6.8k
2
100k
1
D528
1
1
1SS133 R534 D501 R503 R533 D527
1
1SS133 10k 100k 1SS133
100k
5.6k
22k
R543
R542
V-12V
Q522 Q521
D524
1SS133
GNDP
2SA970(BL) 2SC2240(BL) R545
R507 D503 2.2k
R512 2.2k
1.2k 1SS133
Q541
D504 Q502 Q501 2SC2240(BL)
1SS133 2SA970(BL) 2SC2240(BL)
TAD-M600
C505 Q505 Q542
220p 2SC2240(BL) 2SC2240(BL)
D559
D563 1SS133
1SS133
R529 D560
D564 1SS133 R509
3
3
220k
R528
220k
D565 D561 1SS133
1SS133
D566
1SS133 C524 C523 D562 C504 C503
33u/25 33u/25 1SS133 33u/25 33u/25
Q504 Q503
2SA970(BL) 2SC2240(BL)
Q524 Q523
2SA970(BL) 2SC2240(BL)
R551
4.7k
Q551
DTC143ES
4
4
2.2k
R552
C552
0.01u/50 C551
0.022u/50
MTF
R556 R555
1.2k 4.7k
R582 R581 Q553
3.9k 22k 2SA970(BL)
The
!
R583
5 6 7 8
PROTECTION UNIT A
(CWH1521)
The ! mark found on some component parts should be replaced with same parts (safety regulation authorized)
of identical designation.
1SS133
D552
R572
68k
0.022u/50
2SC2240(BL)
R563
R565
R567
R570
C555
1.0u/50
MTF
2SA965(OY)
2SA970(BL)
10k
4.7k
4.7k
5.6k
Q563
2SC2240(BL) CN504
CDE9090-A
R571
1SS133
120k
D553
Q564
2SA970(BL)
Q557
V-12
DTC114ES
1
Q553
Q558
R558
56k
2 MUTE
Q554
2SA965(OY)
R568
Q562
3 GNDS
47
470(1/2W)
470(1/2W)
820(1/2W)
R569
R574
R573
R575
1k
R564
R559
5.6k
12k
R562
100
Q561
2SA970(BL)
Q559
2SC2240(BL)
R555
R576
4.7k
1 PROTECT +B2
2SC2240(BL)
27k C
Q560
-12V -B2
R557
R561
R566
330k
Q555
2
4.7k
5.6k
2SC2235(OY)
ACH1480-A
GNDS
HZ18L-1
3
R560
ACH1482-A
Q556
8.2k
D551
C553
C554
HZ18L-1
2SC2235(OY)
R556
D554
OPRATION +A1
1.2k
100u 25V
4
220u 25V
5 -12V -A1
6 GNDS
Q565 7 OPRATION +B1
DTC143ES
DTC143ES -12V -B1
8
Q566
9 GNDS
R577
15k
CN505
CDE9080-A
R581
R583
22k
22k
2SC2240(BL)
C581
3.9k
RY591 RY594
3 2 3 2
3 2 3 2
4 4
4 4
KN591 1 KN592 1
1 1
CND5464-A CND5464-A
RY592 RY595
3 2 3 2
3 2 3 2
E
4 4
4 4
1 1
1 1
RY593 RY596
3 2 3 2
3 2 To SP- Terminal 3 2 To SP+ Terminal
CN593 CN594
4 CDE9082-A 4 CDE9083-A
4 4
1 1
1 1
CSR1033-A CSR1033-A
TAD-M600 57
5 6 7 8
1 2 3 4
LED1 UNIT
A
(CWH1522)
LED2 UNIT
(CWH1523)
YELLOW LED
RED LED
SLI-343Y8Y(LM)
SLI-343URC
0.01u/50
0.01u/50
D701
D708
C701
C708
B
SLI-343Y8Y(LM)
SLI-343URC
0.01u/50
0.01u/50
D702
D709
C702
C709
at LED1 A'ssy
From Protection
B6B-EH
at LED2 A'ssy
25V
ACH1478-A
From LED1
C712
4P-SCN
CN701
SLI-343Y8Y(LM)
47u
SLI-343URC
0.01u/50
0.01u/50
PROTECTION(+B2) 1
D703
D710
C703
C710
25V
ACH1478-A
-12V(-B2) 2
C713
OPERATION(+A1) 3
47u
CONT.-12V(-A1) 4
OPERATION(+B1) 5
CONT.-12V(-B1) 6
SLI-343Y8Y(LM)
SLI-343URC
0.01u/50
0.01u/50
D704
D711
C704
C711
at LED1 A'ssy
To LED2
B4B-EH
at LED2 A'ssy
NM
D
CN702
1 PROTECTION(+B2)
SLI-343Y8Y(LM)
JH701
)
VEF1040-A 2 CONT.-12V(-B2)
RD1/4PU0R0J-T
0.01u/50
D705
C705
R701
NM
3 OPERATION(+B1)
4 -12V(-B1)
NM(LED2 A'ssy
JH702
VEF1040-A
SLI-343Y8Y(LM)
0.01u/50
D706
C706
E
GNDS
SLI-343Y8Y(LM)
0.01u/50
D707
C707
58 TAD-M600
1 2 3 4
5 6 7 8
TAD-M600 59
5 6 7 8
F
E
B
A
D
C
60
SIDE A
1
1
J H2 0 2 J H2 0 1
CN203 CN204
5.GNDS
3.GNDS
4.NFB N
1
1
R237
6.CENTER N
C215
2.-OUTB N
1.+OUTB N
R238 C217 FRONT
4.GNDS
11.1 VOLTAGE AMP UNIT
3.TR-E N
1.TR-B N
2.TR-C N
Q221
R231
2
2
C212 C211
C216
V-55 Q222 V+55
VR202
D205
FRONT
CNQ3343-
R234 R233 C214
R230
R229
CWH1515-
D206
VOLTAGE AMP
VOLTAGE AMP UNIT
DOWN
C213
D204 D203
IDLE ADJ
UP
R244
R226 R225
V-55
DIP
R223
VR201
C208
C207
BOND
Q220
TAD-M600
R228 R227 Q219
Q217
11. PCB CONNECTION DIAGRAM
R215
C206
R216
C205
Q218
C210 C209 R221
R222
LF
Q212
3
3
Q211
Q210 Q215
V+55
V+55
R246
R245
Q216
V-55
V-55
+
Q209 Q213
DC ADJ
R247
Q214 R214
R218 Q208 R219
R220 R213 R253 Q205
R254 R207
R208 Q206
R211 Q225 R251
R252
C221
Q226 R212 C225
R210 R209
R206 R205
C227
Q203
BOND
BOND
BOND
Q204
C222
4
4
BOND
C229
R204
Q202
R203
C119
Q201
BOND
V+55 V+55
BOND
R224
BOND
R202
C201
R201
GNDA
1
Designed
GNDA RY181 GNDA by Y.M
KN102
1
KN101
CN101
CN102
GNDA 3.-INPUT
V-55
R124
R102
R101
2.GNDA
C101
V
5 6 7 8
A
SIDE A
B
DC ADJ VR101 IDLE ADJ
1.+INPUT
VR102
3.-INPUT
2.GNDA
CN101
C121
- +
R131
V+55 DOWN UP
1
R201 R101 V+55
R121
R115
BOND D105
CN104
Q113
Q115
R123
Designed
by Y.M
C114
R151
R107
R119
02 R102
C109
1.TR-B P
C111
2.TR-C P
Q117
Q119
R125
C125 3.TR-E P
R117
BOND
JH101
4.GNDS
Q125
Q105
D101
1.+OUT P
4 R124 2.-OUT P
D103
3.GNDS
4.NFB P
V+55
5.GNDS
GNDA
R111
R153
C115
BOND
Q107
R144
R129
C
Q109
1
Q111
CN103
C105 C107
C129
BOND
KN101
R130
R127
FRONT
Q103
R105
R109
R113
Q101
V+55
Q121
R145
JH102
C113
R133
R137
R103
C117
D106
R147
C127 BOND
R104
R134
R138
KN102
R146
FRONT
Q102
R114
D
Q122
R110
R128
GNDA
GNDA
R106
V+55
Q104
C106 C108
Q108
Q110
Q112
C116
R112
R154
RY181
V-55
D104
Q118
Q120
R126
C112
D BOND
Q126
Q106
R118
C120
C110
D102
R152
R108
R120
DIP
Q114
Q116
V-55
GNDA
R122
R116
BOND
V-55
E
C181
D BOND
V-55 CN181
D181
D182
2.MUTE
C122
2.GNDA
V-55
C182
1.V-12
1.V+55
3.V-55
1
1 CN102
TAD-M600 61
5 6 7 8
F
E
B
A
D
C
62
SIDE B
1
1
JH102 JH101
1
1
CN103 CN104
5.GNDS
3.GNDS
4.NFB P
4.GNDS
1
3.TR-E P
1.TR-B P
2.TR-C P
6.CENTER P
2.-OUT P
R137 R131
1.+OUT P
R138
C116 C115
1.V-12
2.MUTE C117
2
2
C181
Q122 Q121
R130
C112
IDLE ADJ
R134 R133
VR102
D105
R129 C111
VOLTAGE AMP UNIT
D182
D104 D106 C114
D103
R144
VR101
R126 R125
C113
DC ADJ
C182
R123
C108
C107
R127
D181
TAD-M600
Q120
R116 R128 Q119 R115
Q117
Q118
C106
C105
R122 R121
C110
Q111 C109
3
3
Q112
R146
R145
R147
Q109 Q115
Q116
Q110
D102 D101
R108 R107
R106 R105
C122 C121
C127
C125
Q104
Q103
C129
4
4
Q102
Q101
R103
R104
1.+INPUT
3.V-55
C120
2.GNDA 2.GNDA
C101
1.V+55
R124
R101
3.-INPUT
R102
1
GNDA
CN102
KN101
KN102
RY181
CN101
1
R202
R201
R224
C1
C20
20
2.GNDA 2.GNDA
C101
1.V+55
R124
R101
3.-INPUT
R102
1
GNDA
CN102
KN101
KN102
RY181
CN101
1
R202
R201
R224
C201
C119
Q202
R204
R203
Q201
5
5
C229
Q204
Q203
C222 C221
R206 R205
C225
C227
R210
Q226 Q225
R252 R209 R251
R220 R254
R253 R219
Q206 Q208 Q205
Q207
R218 R217 Q213
D202 D201
Q214
Q216 Q209
Q210 Q215
6
6
R246
R247
R245
C210 C209
Q212 Q211
R222 R221
C205
C206
LF
R215
Q218
Q217
R216 Q220 R228
Q219
R227
VR201
C213 R223
C208
C207
R226 R225
D204 R244 D203
TAD-M600
D206
DC ADJ
R229
C211
C214
R234 R233
D205
C212
VR202
R230
Q222 C217
IDLE ADJ
7
7
Q221
R231
C216 C215
CNQ3343-B
R237
R238
VOLTAGE AMP
CN203 CN204
1
2.-OUT N
1.+OUT N
1
5.GNDS
3.GNDS
4.NFB N
4.GNDS
3.TR-E N
1.TR-B N
2.TR-C N
6.CENTER N
JH202 JH201
8
8
63
SIDE B
F
E
B
A
D
C
1 2 3 4
E E E E E E R437 R46
Q401 Q403 Q4 0 5 Q4 0 7 Q4 0 9 Q4 1 1
BOND
R401
R405
R411
C401
R407
R409
R413
C491
R435
CN491
C407
R431
R433
C
R417
R419
R421
R423
R425
CN403
D401 C411
1.OVLD- KN
2.AMP OUT N C403
3.GNDA
+
KN401 KN402
CN401
AMPOUT N GND
1.+OUT N C404 C405
2.-OUT N
3.NFB D402
4.CENTER
D
KN4
C408
R404
-B
LF
R430
R432
R434
R436
R438
CNQ3344-
R418
R420
R422
R424
R426
Power Amp.
R406
C402
R408
R412
R410
R414
CN402
R402
CWH1516-
4.GNDA Q4 0 2 Q4 0 4 Q4 0 6 Q4 0 8 Q4 1 0 Q4 1 2
3.AMPOUT N
E
2.OVLD-
1.OVLD+
E E E E E E
DIP
64 TAD-M600
1 2 3 4
5 6 7 8
SIDE A
A
B
Q492
437 R463 E E E E E E
Q4 6 1 Q4 5 9 Q4 5 7 Q4 5 5 Q4 5 3 Q4 5 1
BOND
R451
R461
R459
R455
R457
C451 C492
CN492
R479
C414 C413
BOND
R487
R485
R483
R481
R453
C457
C
R475
R473
R471
R469
R467
CN453
C410 D451
KN403 1.OVLD+
C453 2.AMPOUT P
+B 3.GNDA
KN451
CN451
02 R441
D AMPOUT P
1.+OUT P
2.-OUT P
3.NFB
4.CENTER
D452
D
KN404
R454
C458
-B
F
R488
R486
R484
R482
R480
4.GNDA
CNQ3344-
CN452
3.AMPOUT P
R476
R474
R472
R470
R468
2.OVLD-
R452
1.OVLD+
Power Amp.
R464
R462
R460
R458
C452
R456
CWH1516-
CN493
Q4 6 2 Q4 6 0 Q4 5 8 Q4 5 6 Q4 5 4 Q4 5 2
TH490
DIP E E E E E E
POSISTER
TAD-M600 65
5 6 7 8
1 2 3 4
SIDE B
A
Q492 C451
R455
R457
R459
R461
R451
C492
C413 C41
CN492
R471
R479
R467
R481
R469
R483
R485
R473
R487
R475
R453
C457
C
C410
CN453
KN403
D451
KN451
R441
C453
CN451
KN402
KN404
D452
D
C458
R454
L
R480
R468
R470
R482
R472
R484
R474
R486
R476
R488
CNQ3344-B
CN452
Power Amp.
CWH1516-
R452
R456
R458
R460
R462
R464
C452
CN493
E
DIP
66 TAD-M600
1 2 3 4
463
C413
KN403
KN404
KN402
DIP
Power Amp.
CNQ3344-B
CWH1516-
C414
R437
C411
LF
R414
5
5
R426 R425
C405
R412 R438 R435 R413
R424 R423
C404
R410 R436 R433 R411
R422 R421
6
6
KN401
R408 R434 R431 R409
R420 R419
TAD-M600
R418 R417
R430
R405
7
R402
7
C408 C407
C402
R403
D402
D401
C401
R404
C403 R401
CN402
C491
Q491
CN491
CN403
CN401
8
8
67
SIDE B
F
E
B
A
D
C
1 2 3 4
PRIMARY UNIT
KN602
N(fromAC)
LF
REPLACE FUSE AS MARKED.
CN607
N(toCN612)
(to P-SW)
KN
KN604
CN610
KN603 2(Nt
1(LtoT1) 2(NtoT1)
KN601
L(fromAC)
C602
R601
C601
RISK OF FIRE-
CAUTION-
L(toCN611)
C603
CN609
C604
B RY601 RY602 RY604
H601
H603
H606
C613
(to SubTrans)
C610
CN608
1A 125V
H605
10A 300V
10A 300V
H602
H604
N(fromCN610)
FU3
FU1
FU2
CN611
CN612
L(fromCN609)
D6 0 2 D601 D604 D6 0 3 D608 D60
C
CWH1517-
CWH1518-
C607 C606 C612 C611 C615 C61
CWH1519-
PRIMARY SECONDARY
SIDE B
PRIMARY UNIT
D PRIMARY SECONDARY
CN611 CN612
H602
H604
H605
CN608
C604
C610
C613
RY601
RY602
RY604
E
H606
H601
H603
CUT
CUT
CN609
C603
C601
C602
R601
KN601
CUT
CUT
CN610
CN607
68 TAD-M600
1 2 3 4
5 6 7 8
SIDE A
A
CNQ3345-
R686
R682
R681
C655
C657
D681
R685
IC651
R684
R683
Q683
D682
C681
R688
KN606 KN605
2(NtoT2) 1(LtoT2) R687
Q681
Q682
C682
C602
R602
REPLACE WITH SAME TYPE
CAUTION-
NO.49101.6 MFD BY LITTELFUSE INC. C683
FOR P651 AND P652.
R654
P651
C653
D652
C659
C605
49101.6
1.6A 125V B
(from SubTrans)
RY604 RY603
C651
CN652
D651
CN651
C613
C652
R651
R689
C660
D653
C654
P652
R655
49101.6 7.GNDS
D655
6.PRT LT
1.6A 125V 5.GNDS
4.V-12U
FU2
D654
D683
R652 3.V-12V
2.GNDP
1.V+12V
R690
D656
C662
R653
Q684
Q685
C661
R691
ATTENTION- C
C658
C656
EN CAS DE REMPLACEMENT DES FUSIBLES IC652
C615 C614 C609 C608 P651 ET P652 N’UTILISER QUE LA
REFERENCE 49101.6 DE CHEZ
D685
SIDE B
D
D685
C656
C658
C662
R653
R690
C661
Q684
R652
D655
D683 D654
R689
P652
D653
C654
R651
R655
C660
C652
C613
CN651
C605
RY604
RY603
D651
E
CN652
C651
R654
C653
D652
C659
CUT
P651
C602
R602 C683
CUT
R688
C682 Q682
R683
C681
D681
Q681
R687
Q683
IC651
R684
D682
R681
R686
R682
C655
C657
KN606 KN605
R685
CNQ3345-B
PRIMARY ASSY D684
F
TAD-M600 69
5 6 7 8
1 2 3 4
N 1
3)
1( 5
o.
3
N
K
T
CAUTION-
M
O
4)
REPLACE WITH SAME TYPE NO.491010
1( 55
R
o.
MFD.BY LITTELFUSE INC.
N
3
FOR P301 AND P302.
N
T
K
2
ATTENTION-
4)
M
35
o.
3)
O
EN CAS DE REMPLACEMENT DES
D353
o.
N
2(
F
FUSIBLES P301 ET P302 N’UTILISER
N
K
2(
QUE LA REFERENCE 491010 DE CHEZ
T
6
LITTELFUSE INC.
M
35
R
O
F
CN351
N
R
R355
D301
F
K
T R
LA O
E
NC
P IT
B
R315
D354
H C
GNDA
T A
R P
A A
E C
R351 P301 491010
IN
R353
10A 125V
A
M
BO
O
T
D351
C321
TR
E
LA O
R321
R316
P IT
H C
KN354
T A
R P
D302
A A
V-B
E C
C351
IN
P302
A
M 491010
CN301 10A 125V
O
TO MAIN
D352
1.T1(No.5)
2.T1(No.6)
CAPACITOR
C302
(-)
C
DIP REGULATOR KN353
V+B
CN302
LF
CWH1520-
1.T2(No.5)
2.T2(No.6)
CNQ3346-
TO MAIN
CAPACITOR
(+)
SIDE B
D
REGULATOR UNIT
1.T2(No.5)
2.T2(No.6)
V+B
CNQ3346-B KN353
REGULATOR
D352
CN302
LF
CN301
V-B
1.T1(No.5)
2.T1(No.6)
KN354
P302
C351
D351
D302
R316
C321
E R321
R353
P301
D354
R351
T2:No.3 GNDA
KN356
CN351
R315
D301
R355 NC
T2:No.4
KN352
D353
T1:No.4
KN355
F T1:No.3
KN351
70 TAD-M600
1 2 3 4
5 6 7 8
SIDE A
A
VOLTAGE
ADJ
+
Q303 R313
BOND Q301
-
+
E TYPE NO.491010
R303
C305
USE INC. VR301
VOLTAGE CHECK
R301
302. 1.V+55
C301 2.GNDA
3.V-55
ACEMENT DES
N’UTILISER
1010 DE CHEZ
CN303
+
Q305
D303
BOND
D301
C311
C303
R3 0 5
D305
R315
R309 B
Q309
BOND
Q307
D307
D309
R311
CN304
C309
- -+
BOND +
C304
C310
D310
D308
Q308
R312
Q310
R316
C312
R310
D306
R3 0 6
BOND
D302
D304
Q306
1.V+55
5V BOND
C302
- 2.GNDA
3.V-55
LF
R304
C306 VR302 C
VOLTAGE
R302
- Q302
DIP
+
BOND
ADJ
Q304 R314
SIDE B
Q304 R314
C306
LF
R304
R302
VR302
Q302
C302
Q306
D304
D306
R310
R306
D302
R316
C310
C304
Q310
D308
C312
Q308
R311 1.V+55
D307
Q309
D309
C311
303C
R315
Q307
D301
R305
C309
D305 D303
R309
CN303
3.V+55
Q305
2.GNDA
C301
1.V+55
VR301
R301
Q301
R303
C305
F
R313
Q303
TAD-M600 71
5 6 7 8
CNQ3347-B
TION ASSY
F
CNQ3347
L
Q565
Q566
66
R577
R577
PROTEC
1.V-12
65
D554
D554
R571 R571
-12V
2
R569
1
+
Q561
Q562
Q561
D553 D553
C555
R570
Q563
R570
R569
C555
Q562
D551
C554
R567
R567
D551
C553
R568 R568
C554
-12V
Q560
Q558
Q558
Q557
Q560
Q559
R560
R559
C553
R562
R565
R564
R563
R563
R564
R565
R566
R562
R559
R560
R566
Q559
Q557
-12V
+12V +12V
Q555
Q556
Q581
4
4
Q581
Q554
Q555
Q556
R561
R558
Q554
R582
R581
C581
R583
R583
C581
R581
R582
R558
R557
R561
R557
GNDS
GNDP
GNDS
Q553
Q552
R556
C552
R555
R554
C551
R553
R553
C551
R554
R555
C552
R556
Q553
Q552
GNDP
GNDS
Q504 Q524 Q524
Q551
Q551
R551
R552
R552
R551
D566 D566 Q504
Q503 Q523 Q523
DIP
D565 D565
D559
D563
-12V
C523
D563 D560
C503
D561
D564
C524 C504
D561
C505
+12V
3
3
C505
D503 R507 D523 R527 R527 D523 R507 D503
R512 R512
Q502 Q522
D524
D504
D504
D524
Q501 Q521
Q522 Q502
CWH1521-
Q542
Q542
Q521 Q501
D5 0 7 D508 D5 2 7 D5 2 8 D528 D527 -12V D508 D507
TAD-M600
R544 R544
R513 R514 R533 R534 +12V
GNDA
GNDA
Q541
R534 R533 R514 R513
Q541
R503 R504 R523 R524 R524 R523 R504 R503
+12V
PROTECTION UNIT
PROTECTION UNIT
D501 D502 D521 D522
R542
R545
R542
R545
GNDA GNDA
D522 D521 D502 D501
C501
C502
C521
C522
C5 2 2 C521 C502 C5 0 1
R543
R541
R541
R543
2
2
R522
R530
R521
R511
R502
R510
R501
R510
R502
R511
R521
R530
R522
R531
R531
R501
C541
C541
1.POSI
2.GND
11.5 PROTECTION UNIT
1.OVLD DCT+N
1.OVLD DCT+P
2.OVLD DCT-N
2.OVLD DCT-P
3.AMP OUT P
2.OVLD DCT-P
1.OVLD DCT+P
4.GNDS
3.AMP OUT N
2.OVLD DCT-N
1.OVLD DCT+N
3.AMP OUT N
3.AMP OUT P
4.GNDS
4.GDNA
4.GDNA
2.GND
1.POSI
CN503 CN5 0 2 CN5 0 1
CN501 CN502 CN503
1
1
SIDE A
SIDE B
72
C
D
A
F
5 6 7 8
SIDE A
A
D555 C557
3.GNDS
2.MUTE
1.V-12
GNDS
R567
Q563
CN507
+ CN504
SP OUT N
1
2 7.GNDS
R568
V D556 C556
RY591
RY592
RY593
6.PRT LT
D553
R571
Q564
C532
5.GNDS
D551
AMP OUT N
4.V-12U
KN591
R572
3.V-12
-12V
CN593
2.GNDP
C531
GNDP
1.V+12
C554
D552
CN505
LF
-12V
-12V
9.GNDS
C555
R574 8.CONT-B1
B
CN594
D554
AMP OUT P
7.OPE +B1
KN592
6.GNDS
SP OUT P
Q561 4.OPE +A1
3.GNDS
RY594
RY595
RY596
R576
2.-12V -B2
C553
1.PROTECT +B2
D558 C559
Q562 Q566 R575
R570 R577
CNQ3347-
SIDE B
CNQ3347-B
PROTECTION ASSY
C558
D557
D558
C559
R570 CN505
R577
Q562 -12V
R575 1.PROTECTION
RY594
RY595
RY596
Q566
2.-12V -B2
R576
3.GNDS
+12V
Q561
R573 4.OPE +A1
E
KN592
Q565
5.CONT -A1
R569
CN594
6.GNDS
LF
+12V
-12V
9.GNDS
D552
C554
CN507
CN593
C531
1.V+12
KN591
Q
2.GNDP
R572
3.V-12
Q564
D551
4.V-12U
C532
D553
R571
RY591
RY592
RY593
5.GNDS
R568
6.PRT LT
7.GNDS C557
2.MUTE
D556
3.GNDS
1.V-12
Q563
GNDS
Q R567
CN504 D555 C556
F
TAD-M600 73
5 6 7 8
SIDE A
SIDE B
4
4
LED ASSY
LED1 ONLY JH702
JH702
CNQ3348-A
CWH1522- LED1
CWH1523- LED2
C707
C707
D707
DIP
D707
C706
1.PROTECTION(+B2)
C706
D706
1.PROTECTION(+B2)
D706
2.CONT.-12V(-B2)
D711
2.CONT.-12V(-B2)
3
3.OPERATION(+B1)
3
3.OPERATION(+B1)
4.-12V(-B1)
4.-12V(-B1)
D711
C711
C711
R701
R701
CN702
CN702
C705
C705
D705
D705
D710
D710
C710
C710
TAD-M600
D704
C704
C704
D704
D709
CNQ3348-
C712
C712
D709
C709
C709
D703
D703
C703
C703
D708
C713
C713
C708
C708
D708
D702
D702
C702
C702
1.PROTECTION(+B2)
2.-12V(-B2)
LED ASSY
3.OPERATION(+A1)
11.6 LED1 and LED2 UNITS
2
2
4.CONT.-12V(-A1) 1.PROTECTION(+B2)
CN701
D701
C701
C701
LED1 UNIT
LED2 UNIT
LED1 UNIT
LED2 UNIT
D701
LED2
2.-12V(-B2)
CN701
3.OPERATION(+A1)
4.CONT.-12V(-A1)
5.OPERATION(+B1)
5.OPERATION(+B1)
6.CONT.-12V(-B1)
6.CONT.-12V(-B1)
JH701 JH701
LED2 ONLY
1
1
SIDE A
SIDE B
74
C
D
A
F
5 6 7 8
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47 k ohm (tolerance is shown by J = 5%,
and K = 10%).
560 Ω → 56 × 101 → 561 ................................................................... RD1/4PU 5 6 1 J
47 kΩ → 47 × 103 → 473 ................................................................... RD1/4PU 4 7 3 J
0.5 Ω → R50 ................................................................................................. RN2H R 5 0 K
1Ω → 1R0 ................................................................................................. RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62 kΩ → 562 × 101 → 5621 ................................................................. RN1/4PC 5 6 2 1 F
- Meaning of the figures and others in the parentheses in the parts list. B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.
IC 301 (A, 91, 111) IC NJM2068V
Mark No. Description Part No. Mark No. Description Part No.
C 407,408,457,458 CFTNA105J2A
LIST OF ASSEMBLIES C 410,411 CCE1040
1..POWER AMP UNIT CWH1516
C 413,414 CCH1953
1..PRIMARY UNIT (TAD-M600/U) CWH1518
1..PRIMARY UNIT (TAD-M600/Y5) CWH1519 C 491,492 VCE1052
1..PROTECTION UNIT CWH1521
1..LED1 UNIT CWH1522
C
1..LED2 UNIT CWH1523
1..VOLTAGE AMP UNIT CWH1515 PRIMARY UNIT
1..REGULATOR UNIT CWH1520 SEMICONDUCTORS
IC 651 NJM7812FA
IC 652 NJM7912FA
Q 681,682,684 2SC2240
Q 683,685 2SC2235
D 601-608,652,653 11EQS10
Mark No. Description Part No. D 651 D3SBA20
POWER AMP UNIT D 654,655,682 1SS133
SEMICONDUCTORS D 656 HZ12L(A2)
D 401,402,451,452 FSF10A20 D 681 HZ18L(3)
D
D 683 HZ18L(1)
MISCELLANEOUS
KN 401 CORD CDE9078 MISCELLANEOUS
KN 402-404 HOLDER CND5464 H 601-604 FUSE HOLDER AKR7004
KN 451 CORD CDE9079 H 605,606 FUSE HOLDER AKR7005
CN 401 CORD CDE9073 KN 601-606 HOLDER CND5464
CN 402 CORD CDE9087 RY 601-604 RELAY CSR1032
CN 607,608,651 CONNECTOR CKS6112
CN 403,453 CONNECTOR CKS6112
CN 451 CORD CDE9072 CN 609 CORD CDE9070
CN 452 CORD CDE9088 CN 610 CORD CDE9071
CN 491 CORD CDE9077 CN 652 CORD CDE9089
CN 492 CORD CDE9076 693 HEAT SINK CND5521 E
694 SCREW PMH30P080FCC
CN 493 CORD CDE9086
494 PCB CNQ3344 FU 1,2 FUSE (10 A/400 V) (TAD-M600/U) CEK1374
FU 1,2 FUSE (8 A/250 V)(TAD-M600/Y5) CEK1378
RESISTORS FU 3 FUSE (1 A/125 V)(TAD-M600/U) REK1142
FU 3 FUSE (630 mA/250 V)(TAD-M600/Y5) AEK1052
R 401,402,451,452 CCN1193
P 651,652 PROTECTOR(1.6 A) AEK7012
R 403,404,453,454 CCN1277
R 405-414,455-464 CCN1198
R 417-426,467-476 CCN1271 RESISTORS
R 429-438,479-488 CCN1194 R 601,602 CCN1269
R 652 RD1/2PM122J
R 441 CCN1204 Other Resistors RD1/4PU###J
F
CAPACITORS CAPACITORS
C 401,402,451,452 VCE1051 C 601,602 ACE7013
C 403-405,453 CCE1045 C 603-605,610,613 ACG7039
TAD-M600 75
5 6 7 8
1 2 3 4
Mark No. Description Part No. Mark No. Description Part No.
C 606-609,611,612 CFTNA103J50 LED1 UNIT
C 614,615,651,652 CFTNA103J50
SEMICONDUCTORS
C 653,654 CEHAZL222M25
A D 701-707 SLI-343Y8Y(LM)
D 708-711 SLI-343URC
C 655-658,662 CFTNA103J50
C 659,660 CCH1951
C 661 CEHAT100M50
MISCELLANEOUS
CN 701 CONNECTOR B6B-EH
C 681 CEANP1R0M50
C 682 ACH1478 CN 702 CONNECTOR B4B-EH
JH 702 PCB BINDER VEF1040
C 683 CQMA221J50
CAPACITORS
C 701-711 CFTNA103J50
C 712 ACH1478
PROTECTION UNIT
B SEMICONDUCTORS
Q 501,503,505,521 2SC2240
Q 502,504,522,524 2SA970
LED2 UNIT
Q 523,541,542,552 2SC2240 SEMICONDUCTORS
Q 551,565,566 DTC143ES D 701-707 SLI-343Y8Y(LM)
Q 553,561,564 2SA970 D 708-711 SLI-343URC
76 TAD-M600
1 2 3 4
5 6 7 8
Mark No. Description Part No. Mark No. Description Part No.
CN 102 CONNECTOR CKS6112 VR 301,302 SEMI FIXED RESISTOR CCP1568
CN 103,203 CONNECTOR B6B-EH CN 301,302,351 CONNECTOR CKS6111
CN 104,204 CONNECTOR B4B-EH CN 303 CONNECTOR CKS6112
CN 181 2P TOP POST B2B-EH CN 304 CORD CDE9059 A
R 205,206,211,212 CCN1232
R 207,208,223,244 CCN1237
R 217,218,221,222 CCN1230
R 225,226,253,254 CCN1230
R 251,252 CCN1237
CAPACITORS
C 101,201 CCE1044
C 105-108,205-208 CCF1008 D
C 109-112,114,125 CCH1965
C 113,121,122,213 CCE1041
C 115,116,215,216 CCE1043
C 117,217 CCE1045
C 119,120 CCH1953
C 127,227 CCE1056
C 129,209-212,214 CCH1965
C 181,182 CFTNA105J50
C 221,222 CCE1041
C 225,229 CCH1965
E
REGULATOR UNIT
SEMICONDUCTORS
Q 301 2SC4883A
Q 302 2SA1859A
Q 303,305,308-310 2SC2240
Q 304,306,307 2SA970
D 301 FCH20A20
D 302 FRH20A20
D 303-310 SLI-343URC F
MISCELLANEOUS
KN 351-356 HOLDER CND5464
TAD-M600 77
5 6 7 8