Академический Документы
Профессиональный Документы
Культура Документы
B Side
A JAPANESE
Side
B ENGLISH
contents directly.
Hardware Manual Incorrect handling of the battery may cause heat excessive generation,
bursting, ignition, liquid leakage or deformation, and lead to injury, fire or
MELSEC iQ-F FX5
User's Manual JY997D55901
Explains the N:N network,
MELSEC Communication
1. Outline
protocol, inverter communication
failures and malfunction of facilities and other equipment. (Serial Communication) 1.1 Part names
and non-protocol communication.
Manual Number JY997D61001 Front panel Front panel Under side
STARTUP AND MELSEC iQ-F FX5 (Connector type) (Spring clamp
Revision F Explains the MODBUS serial
MAINTENANCE User's Manual JY997D56101 terminal block type)
communication.
Date July 2017 PRECAUTIONS (MODBUS Communication)
[5] [11]
Do not disassemble or modify the PLC. MELSEC iQ-F FX5 [1] [6]
Functions for communication via
This manual describes the part names, dimensions, installation, cabling and Doing so may cause fire, equipment failures, or malfunctions. User's Manual JY997D56201
built-in Ethernet port.
specifications for the product. This manual is extracted from MELSEC iQ-F For repair, contact your local Mitsubishi Electric representative. (Ethernet Communication)
[4] [12]
FX5UC User's Manual (Hardware). Refer to MELSEC iQ-F FX5UC User's Turn off the power to the PLC before connecting or disconnecting any [7]
Manual (Hardware) for more details. Before use, read this manual and extension cable.
manuals of relevant products fully to acquire proficiency in the handling and Failure to do so may cause equipment failures or malfunctions.
Certification of UL, cUL standards [16]
operating the product. Make sure to learn all the product information, safety Turn off the power to the PLC before attaching or detaching the following
information, and precautions. [3]
devices.
And, store this manual in a safe place so that you can take it out and read it Failure to do so may cause equipment failures or malfunctions. Please consult with Mitsubishi Electric for information on UL, cUL standard
whenever necessary. Always forward it to the end user. practices and the corresponding types of equipment. [15]
- Peripheral devices, expansion adapter, and connector conversion
Registration: Ethernet is a trademark of Xerox Corporation. MODBUS is a adapter [2] [13]
registered trademark of Schneider Electric SA. The company name and the - Extension modules, bus conversion module, connector conversion [8]
product name to be described in this manual are the registered trademarks or module, and battery Compliance with EC directive (CE Marking)
trademarks of each company. [1] [6]
Effective July 2017 DISPOSAL PRECAUTIONS This document does not guarantee that a mechanical system including this
product will comply with the following standards. [10] [9] [14] [17]
Specifications are subject to change without notice.
2015 MITSUBISHI ELECTRIC CORPORATION Compliance to EMC directive of the entire mechanical system should be
Please contact a certified electronic waste disposal company for the
checked by the user/manufacturer. For more details please contact the local
environmentally safe recycling and disposal of your device. Left side Right side
Safety Precautions (Read these precautions before use.) When disposing of batteries, separate them from other waste according to
Mitsubishi Electric sales site.
Attention
This manual classifies the safety precautions into two categories: local regulations.
This product is designed for use in industrial applications.
and . (For details on the Battery Directive in EU countries, refer to the MELSEC
iQ-F FX5UC User's Manual (Hardware).) Caution for compliance with EC Directive [19]
Indicates that incorrect handling may cause hazardous Installation in Enclosure
conditions, resulting in death or severe injury. TRANSPORTATION Programmable controllers are open-type devices that must be installed and
PRECAUTIONS used within conductive control boxes. Please use the FX5UC programmable [20]
Indicates that incorrect handling may cause hazardous controllers while installed in conductive shielded control boxes. Please secure
conditions, resulting in minor or moderate injury or When transporting the PLC with the optional battery, turn on the PLC the control box lid to the control box (for conduction). Installation within a control
property damage. before shipment, confirm that the battery mode is set using a parameter box greatly affects the safety of the system and aids in shielding noise from the
and the BAT LED is OFF, and check the battery life. programmable controller. [21]
If the PLC is transported with the BAT LED ON or the battery exhausted, For other cautions, refer to the MELSEC iQ-F FX5UC User's Manual
Depending on the circumstances, procedures indicated by may
the battery-backed data may be unstable during transportation. (Hardware).
also cause severe injury.
It is important to follow all precautions for personal safety. The PLC is a precision instrument. During transportation, avoid impacts
larger than those specified in the general specifications (Section 2.1) by
STARTUP AND using dedicated packaging boxes and shock-absorbing palettes. Failure to [18] [22]
MAINTENANCE do so may cause failures in the PLC. Incorporated Items
With cover open
PRECAUTIONS After transportation, verify operation of the PLC and check for damage of
the mounting part, etc. Check if the following product and items are included in the package:
Do not touch any terminal while the PLC's power is on.
When transporting lithium batteries, follow required transportation Included Items
Doing so may cause electric shock or malfunctions.
regulations. [25]
Before cleaning or retightening terminals, cut off all phases of the power (For details on the regulated products, refer to the MELSEC iQ-F FX5UC CPU module
supply externally. Failure to do so in the power ON status may cause User's Manual (Hardware).) [24]
Product 1 module
electric shock.
Before modifying the program in operation, forcible output, running or FX2NC-100MPCB [1 m, three
wire]
1 cable [23]
stopping the PLC, read through this manual carefully, and ensure FX5UC-MT/D
complete safety. Associated manuals (: 32, 64, 96) FX2NC-100BPCB [1 m, two wire] 1 cable
An operation error may damage the machinery or cause accidents.
Manuals [Japanese/English] 1 manual No. Name
Do not change the program in the PLC from two or more peripheral
equipment devices at the same time. (i.e. from an engineering tool and a How to obtain manuals Manuals [Chinese] 1 manual [1] Expansion adapter connecting hooks
GOT) For the necessary product manuals or documents, consult with your local Product 1 module [2] Built-in RS-485 communication terminal block
Doing so may cause destruction or malfunction of the PLC program. Mitsubishi Electric representative. FX5UC-MT/DSS FX2NC-100MPCB [1 m, three [3] Built-in Ethernet communication connector (with cover)
FX5UC-32MT/DS-TS 1 cable
wire]
FX5UC-32MT/DSS-TS
(: 32, 64, 96) Manuals [Japanese/English] 1 manual
Manuals [Chinese] 1 manual
No. Name Item Specification 2.3 Procedures for installing to and detaching from DIN rail
Operation status display LEDs
2. Installation (general specifications) Overvoltage
The products can be installed on a DIN46277 rail [35 mm wide]. This section
II or less explains the installations of the CPU modules.
PWR Green On while the PLC is powered. category*9 2.3.1 Installation
As for installation of the I/O modules and expansion adapters, refer to MELSEC
iQ-F FX5UC User's Manual (Hardware). Pollution 1) Push out all DIN rail mounting hooks (below fig. A)
ERR*1 Red Lit/flashing when an error occurs. 2 or less
degree*10
P.RUN Green On while the PLC is running. INSTALLATION
PRECAUTIONS Equipment class Class 2
BAT Red Lit when the battery voltage drops.
[4] Use the product within the generic environment specifications described in *1 The simultaneous ON ratio of available PLC inputs or outputs changes
CARD Green Lit when the SD memory card is inserted. 1
with respect to the ambient temperature. In the case where operating
section 2.1 of this manual.
Lit when data is sent or received through ambient temperature is lower than 0, the specifications are different
SD/RD Green Never use the product in areas with excessive dust, oily smoke,
communication via built-in Ethernet. from the above description. Refer to MELSEC iQ-F FX5UC User's
conductive dusts, corrosive gas (salt air, Cl 2 , H 2 S, SO 2 or NO 2 ), Manual (Hardware).
Lit when data is received through communication via flammable gas, vibration or impacts, or expose it to high temperature,
RD Green *2 The operating ambient temperature is 0 to 55 (32 to 131) for products
built-in RS-485. condensation, or rain and wind.
manufactured before June 2016. For intelligent function modules, refer to 1 A A
Lit when data is sent through communication via If the product is used in such conditions, electric shock, fire, malfunctions,
SD Green the manual for each product.
built-in RS-485. deterioration or damage may occur. 2) Fit the upper edge of the DIN rail mounting groove (right fig. B) onto the
*3 When used in a low-temperature environment, use in an environment DIN rail.
[5] Input connector with no sudden temperature changes. If there are sudden temperature
INSTALLATION
changes because of opening/closing of the control panel or other
[6] Extension module connection hooks PRECAUTIONS
reasons, condensation may occur, which may cause a fire, fault, or
[7] Input/Output display LEDs (Green) Do not touch the conductive parts of the product directly. Doing so may malfunction. Furthermore, use an air conditioner in dehumidifier mode to B
cause device failures or malfunctions. prevent condensation.
[8] DISP switch (for switching Input/Output display LEDs)
When drilling screw holes or wiring, make sure that cutting and wiring *4 The criterion is shown in IEC61131-2.
[9] Output connector
debris do not enter the ventilation slits of the PLC. *5 When the system has equipment which specification values are lower
[10] DIN rail mounting hooks Failure to do so may cause fire, equipment failures or malfunctions. than above mentioned vibration resistance specification values, the
Install the product on a flat surface. If the mounting surface is rough, vibration resistance specification of the whole system is corresponding to
[11] Input terminal
und ue fo rce w il l be a ppl ied t o the P C boa rd, th ereb y cau si ng the lower specification.
[12] Input display LEDs (Green) nonconformities. *6 For dielectric withstand voltage test and insulation resistance test of each
[13] Output display LEDs (Green) Install the product securely using a DIN rail or mounting screws. product, refer to the following manual.
Refer to MELSEC iQ-F FX5UC User's Manual (Hardware). 3) Lock the DIN rail mounting hooks (below fig. C) while pressing the PLC
[14] Output terminal Connect the extension cables, peripheral device cables, input/output
against the DIN rail.
cables and battery connecting cable securely to their designated *7 For grounding, refer to Section 3.2.
[15] Power connector for CPU module connectors. *8 The PLC cannot be used at a pressure higher than the atmospheric
[16] RS-485 terminal resister selector switch Loose connections may cause malfunctions. pressure to avoid damage.
Turn off the power to the PLC before attaching or detaching the following *9 This indicates the section of the power supply to which the equipment is
[17] Battery cover
devices. assumed to be connected between the public electrical power distribution
[18] Expansion adapter connector cover Failure to do so may cause equipment failures or malfunctions. network and the machinery within premises. Category II applies to
[19] Extension connector cover - Peripheral devices, expansion adapter, and connector conversion adapter equipment for which electrical power is supplied from fixed facilities. The
- Extension modules, bus conversion module, connector conversion surge voltage withstand level for up to the rated voltage of 300 V is 2500 V.
[20] DIN rail mounting groove
module, and battery *10 This index indicates the degree to which conductive material is generated
[21] Nameplate*2 in the environment in which the equipment is used. Pollution level 2 is
2.1 Generic specifications when only non-conductive pollution occurs. Temporary conductivity C 3
[22] Genuine product certification label*2 caused by condensation must be expected occasionally.
Item Specification 2.2 Installation location 2.4 Connection of power supply connector
[23] SD memory card disable switch Use the power connector to supply power to the CPU module.
Operating ambient Install the PLC in an environment conforming to the generic specifications
[24] SD memory card slot -20 to 55 (-4 to 131), non-freezing*2 For details, refer to MELSEC iQ-F FX5UC User's Manual (Hardware).
temperature*1 (Section 2.1), installation precautions.
[25] RUN/STOP/RESET switch Installation location in enclosure 2.5 Connection to input/output connector
Storage ambient The input/output connectors of the CPU modules (Connector type) conform to
*1 When powered on in the factory default state, ERR LED starts flashing -25 to 75 (-13 to 167), non-freezing
temperature MIL-C-83503.
because there is no program. For details, refer to the following manual. For details, refer to MELSEC iQ-F FX5UC User's Manual (Hardware).
Operating *3
MELSEC iQ-F FX5UC User’s Manual (Hardware). ambient humidity 5 to 95%RH, non-condensing 1) Compliant connectors (commercially available connectors)
*2 Products that do not have the genuine product certification label or Use a 20-pin (1-key) socket connector conforming to MIL-C-83503.
nameplate are not covered by the warranty. Storage ambient Confirm in advance that the connectors do not interfere with other parts
5 to 95%RH, non-condensing
humidity including connector covers.
1.2 External dimensions and weight
Frequency Acceleration Half amplitude 2) Input/output cables (available from Mitsubishi)
Unit: mm Sweep count
Spring clamp (Hz) (m/s2) (mm) Input/output cables with attached connectors are available.
Connector type terminal block type
Vibration 5 to 8.4 1.75 10 times each in Model names Length Description Shape
resistance*4*5 Installed
X, Y, Z directions Single wire
on DIN
8.4 to 150 4.9 (80 min in each
rail General-purpose (Wire color: red)
direction) FX-16E-500CAB-S 5m
input/output cable PLC side:
Shock 2
147 m/s Acceleration, Action time: 11 ms, A 20-pin connector
90