Академический Документы
Профессиональный Документы
Культура Документы
The purpose is to check the performance of Network. We have categories of KPI and numbers of KPI of each category. In the Optimization process we
have to check the KPI value to monitor and optimize the radio network performance in order to provide better subscriber quality or to achieve better use
of installed network resources . Typically KPI can be categorized into following subcategories:'
Accessibility KPI
Are used to measure properly of whether services requested by users can be accessed in given condition, also refers to the quality of being
available when users needed. eg. user request to access the network, access the voice call, data call, ......
📈 Retainability KPI
Are used to measure how the network keep user's possession or able to hold and provide the services for the users
📈 Mobility KPI
Are used to measure the performance of network which can handle the movement of users and still retain the service for the user, such as
handover,...
📈 Integrity KPI
Are used to measure the character or honesty of network to its user, such as what is the throughput, latency which users were served.
📈 Availability KPI
Are used to measure the availability of network, suitable or ready for users to use services.
📈 Utilization KPI
Are used to measure the utilization of network, whether the network capacity is reached its resource.
KPIs for LTE RAN (Radio Access Network)
LTE KPI INDICATORS
RRC setup success rate
ERAB setup success rate
Accessibility KPI Call Setup Success Rate
Are used to measure properly of whether services requested by users can be accessed in given condition,
also refers to the quality of being available when users needed. eg. user request to access the network,
access the voice call, data call, ......
Call drop rate
Service Call drop rate
Retainability KPI
Are used to measure how the network keep user's possession or able to hold and provide the services for the
users
Intra-Frequency Handover Out Success Rate
Inter-Frequency Handover Out Success Rate
Mobility Inter-RAT Handover Out Success Rate (LTE to WCDMA)
KPI
Are used to measure the performance of network which can handle the movement of users and still retain the
service for the user, such as handover,...
E-UTRAN IP Throughput
IP Throughput in DL
Integrity E-UTRAN IP Latency
KPI
Are used to measure the character or honesty of network to its user, such as what is the throughput, latency
which users were served.
E-UTRAN Cell Availability
Partial cell availability (node restarts excluded)
Availability
KPI Are used to measure how the network keep user's possession or able to hold and provide the services for the
users
Utilization Mean Active Dedicated EPS Bearer Utilization
KPI
Are used to measure the utilization of network, whether the network capacity is reached its resource.
ACCESSIBILITY KPI:
ERAB setup success rate KPI shows the probability of success ERAB to access all services including VoIP in a cell or radio network. KPI is
calculated based counter ERAB connection setup attempt (point A) and successful ERAB setup (point B). The explanation is as given in the
following illustration:
☰ Call Setup Success Rate
Call Setup Success Rate KPI call setup indicates the probability of success for all service on the cell or radio network. KPI is calculated by
multiplying the RRC setup success rate KPI, S1 signaling connection success rate KPI, and ERAB success rate KPI. The table below
describes the definition Call Setup Success Rate:
RETAIN-ABILITY KPI:
☰ Call Drop
VoIP call drop arise when VoIP ERAB release is not normal. Each ERAB associated with QoS information. Here's an illustration of two
procedures being done to release ERAB namely: ERAB release indication and the UE context release request:
MOBILITY KPI:
☰ E-UTRAN IP Throughput
A KPI that shows how E-UTRAN impacts the service quality provided to an end-user.
Payload data volume on IP level per elapsed time unit on the Uu interface. IP Throughput for a single QCI:
To achieve a throughput measurement that is independent of bursty traffic pattern, it is important to make sure that idle gaps between
incoming data is not included in the measurements. That shall be done as considering each burst of data as one sample. ThpVolDl is the
volume on IP level and the ThpTimeDl is the time elapsed on Uu for transmission of the volume included in ThpVolDl.
☰ E-UTRAN IP Latency
A measurement that shows how E-UTRAN impacts on the delay experienced by an end-user.
Time from reception of IP packet to transmission of first packet over the Uu.
To achieve a delay measurement that is independent of IP data block size only the first packet sent to Uu is measured.
To find the delay for a certain packet size the IP Throughput measure can be used together with IP Latency (after the first block on the Uu,
the remaining time of the packet can be calculated with the IP Throughput measure).
T_Lat is defined as the time between receiption of IP packet and the time when the eNodeB transmits the first block to Uu.
Since services can be mapped towards different kind of E-RABs, the Latency measure shall be available per QoS group.
AVAILABILITY KPI:
As for defining the cell as available, it shall be considered available when the eNodeB can provide E-RAB service in the cell.
UTILIZATION KPI: