Академический Документы
Профессиональный Документы
Культура Документы
1. STRUCTURE
This service manual has been prepared as an aid to improve the quality of repairs by giving the
serviceman an accurate understanding of the product and by showing him the correct way to
perform repairs and make judgements. Make sure you understand the contents of this manual and
use it to full effect at every opportunity.
This service manual mainly contains the necessary technical information for operations performed in
a service workshop.
For ease of understanding, the manual is divided into the following sections.
SECTION 1 GENERAL
This section explains the safety hints and gives the specification of the machine and major
components.
SECTION 2 STRUCTURE AND FUNCTION
This section explains the structure and function of each component. It serves not only to give an
understanding of the structure, but also serves as reference material for troubleshooting.
SECTION 3 HYDRAULIC SYSTEM
This section explains the hydraulic circuit, single and combined operation.
SECTION 4 ELECTRICAL SYSTEM
This section explains the electrical circuit, monitoring system and each component. It serves not
only to give an understanding electrical system, but also serves as reference material for trouble
shooting.
SECTION 5 MECHATRONICS SYSTEM
This section explains the computer aided power optimization system and each component.
SECTION 6 TROUBLESHOOTING
This section explains the troubleshooting charts correlating problems to causes
causes.
SECTION 7 MAINTENANCE STANDARD
This section gives the judgement standards when inspecting disassembled parts.
SECTION 8 DISASSEMBLY AND ASSEMBLY
This section explains the order to be followed when removing, installing, disassembling or
assembling each component, as well as precautions to be taken for these operations.
SECTION 9 COMPONENT MOUNTING TORQUE
This section shows bolt specifications and standard torque values needed when mounting
components to the machine.
The specifications contained in this shop manual are subject to change at any time and without any
advance notice. Contact your HYUNDAI distributor for the latest information.
0-1
2. HOW TO READ THE SERVICE MANUAL
Distribution and updating Revised edition mark
mark(①②③…)
Any additions, amendments or other changes will When a manual is revised, an edition mark is
be sent to HYUNDAI distributors. recorded on the bottom outside corner of the
Get the most up-to-date information before you pages.
start any work.
Revisions
Filing method Revised pages are shown at the list of revised
1. See the page number on the bottom of the pages on the between the contents page and
page. section 1 page.
File the pages in correct order.
2. Following examples shows how to read the Symbols
page number. So that the shop manual can be of ample
Example 1 practical use, important places for safety and
2-3 quality are marked with the following symbols.
Item number(2. Structure and
Function)
Consecutive page number for Symbol Item Remarks
each item.
Special safety precautions are
3. Additional pages : Additional pages are necessary when performing the
indicated by a hyphen(-) and number after the work.
Safety
page number. File as in the example. Extra special safety precautions
10 - 4 are necessary when performing
10 - 4 - 1 the work because it is under
Added pages internal pressure.
10 - 4 - 2
10 - 5 Special technical precautions or
※ Caution
other precautions for preserving
standards are necessary when
performing the work.
0-2
3. CONVERSION TABLE
Method of using the Conversion Table
The Conversion Table in this section is provided to enable simple conversion of figures. For details of
the method of using the Conversion Table, see the example given below.
Example
1. Method of using the Conversion Table to convert from millimeters to inches
Convert 55mm into inches.
(1) Locate the number 50in the vertical column at the left side, take this as ⓐ, then draw a
horizontal line from ⓐ.
(2) Locate the number 5in the row across the top, take this as ⓑ, then draw a perpendicular line
down from ⓑ.
(3) Take the point where the two lines cross as ⓒ. This point ⓒ gives the value when converting
from millimeters to inches. Therefore, 55mm = 2.165 inches.
Millimeters to inches ⓑ
1mm = 0.03937 in
0 1 2 3 4 5 6 7 8 9
0-3
Millimeters to inches 1mm = 0.03937in
0 1 2 3 4 5 6 7 8 9
50 1.969 2.008 2.047 2.087 2.126 2.165 2.205 2.244 2.283 2.323
60 2.362 2.402 2.441 2.480 2.520 2.559 2.598 2.638 2.677 2.717
70 2.756 2.795 2.835 2.874 2.913 2.953 2.992 3.032 3.071 3.110
80 3.150 3.189 3.228 3.268 3.307 3.346 3.386 3.425 3.465 3.504
90 3.543 3.583 3.622 3.661 3.701 3.740 3.780 3.819 3.858 3.898
0 1 2 3 4 5 6 7 8 9
50 110.23 112.44 114.64 116.85 119.05 121.25 123.46 125.66 127.87 130.07
60 132.28 134.48 136.69 138.89 141.10 143.30 145.51 147.71 149.91 152.12
70 154.32 156.53 158.73 160.94 163.14 165.35 167.55 169.76 171.96 174.17
80 176.37 178.57 180.78 182.98 185.19 187.39 189.60 191.80 194.01 196.21
90 198.42 200.62 202.83 205.03 207.24 209.44 211.64 213.85 216.05 218.26
0-4
Liter to U.S. Gallon 1ℓ = 0.2642 U.S.Gal
0 1 2 3 4 5 6 7 8 9
50 13.209 13.473 13.737 14.001 14.265 14.529 14.795 15.058 15.322 15.586
60 15.850 16.115 16.379 16.643 16.907 17.171 17.435 17.700 17.964 18.228
70 18.492 18.756 19.020 19.285 19.549 19.813 20.077 20.341 20.605 20.870
80 21.134 21.398 21.662 21.926 22.190 22.455 22.719 22.983 23.247 23.511
90 23.775 24.040 24.304 24.568 24.832 25.096 25.631 25.625 25.889 26.153
0 1 2 3 4 5 6 7 8 9
50 10.998 11.281 11.438 11.658 11.878 12.098 12.318 12.528 12.758 12.978
60 13.198 13.418 13.638 13.858 14.078 14.298 14.518 14.738 14.958 15.178
70 15.398 15.618 15.838 16.058 16.278 16.498 16.718 16.938 17.158 17.378
80 17.598 17.818 18.037 18.257 18.477 18.697 18.917 19.137 19.357 19.577
90 19.797 20.017 20.237 20.457 20.677 20.897 21.117 21.337 21.557 21.777
0-5
kgf·m to lbf
kgf lbf·ftft 1kgf·m = 7.233lbf·ft
0 1 2 3 4 5 6 7 8 9
50 361.7 368.9 376.1 383.4 390.6 397.8 405.1 412.3 419.5 426.8
60 434.0 441.2 448.5 455.7 462.9 470.2 477.4 484.6 491.8 499.1
70 506.3 513.5 520.8 528.0 535.2 542.5 549.7 556.9 564.2 571.4
80 578.6 585.9 593.1 600.3 607.6 614.8 622.0 629.3 636.5 643.7
90 651.0 658.2 665.4 672.7 679.9 687.1 694.4 701.6 708.8 716.1
100 723.3 730.5 737.8 745.0 752.2 759.5 766.7 773.9 781.2 788.4
110 795.6 802.9 810.1 817.3 824.6 831.8 839.0 846.3 853.5 860.7
120 868.0 875.2 882.4 889.7 896.9 904.1 911.4 918.6 925.8 933.1
130 940.3 947.5 954.8 962.0 969.2 976.5 983.7 990.9 998.2 10005.4
140 1012.6 1019.9 1027.1 1034.3 1041.5 1048.8 1056.0 1063.2 1070.5 1077.7
150 1084.9 1092.2 1099.4 1106.6 1113.9 1121.1 1128.3 1135.6 1142.8 1150.0
160 1157.3 1164.5 1171.7 1179.0 1186.2 1193.4 1200.7 1207.9 1215.1 1222.4
170 1129.6 1236.8 1244.1 1251.3 1258.5 1265.8 1273.0 1280.1 1287.5 1294.7
180 1301.9 1309.2 1316.4 1323.6 1330.9 1338.1 1345.3 1352.6 1359.8 1367.0
190 1374.3 1381.5 1388.7 1396.0 1403.2 1410.4 1417.7 1424.9 1432.1 1439.4
0-6
kgf/cm2 to lbf/in2 1kgf / cm2 = 14.2233lbf / in2
0 1 2 3 4 5 6 7 8 9
50 711.2 725.4 739.6 753.8 768.1 782.3 796.5 810.7 825.0 839.2
60 853.4 867.6 881.8 896.1 910.3 924.5 938.7 953.0 967.2 981.4
70 995.6 1010 1024 1038 1053 1067 1081 1095 1109 1124
80 1138 1152 1166 1181 1195 1209 1223 1237 1252 1266
90 1280 1294 1309 1323 1337 1351 1365 1380 1394 1408
100 1422 1437 1451 1465 1479 1493 1508 1522 1536 1550
110 1565 1579 1593 1607 1621 1636 1650 1664 1678 1693
120 1707 1721 1735 1749 1764 1778 1792 1806 1821 1835
130 1849 2863 1877 1892 1906 1920 1934 1949 1963 1977
140 1991 2005 2020 2034 2048 2062 2077 2091 2105 2119
150 2134 2148 2162 2176 2190 2205 2219 2233 2247 2262
160 2276 2290 2304 2318 2333 2347 2361 2375 2389 2404
170 2418 2432 2446 2460 2475 2489 2503 2518 2532 2546
180 2560 2574 2589 5603 2617 2631 2646 2660 2674 2688
200 2845 2859 2873 2887 2901 2916 2930 2944 2958 2973
210 2987 3001 3015 3030 3044 3058 3072 3086 3101 3115
220 3129 3143 3158 3172 3186 3200 3214 3229 3243 3257
230 3271 3286 3300 3314 3328 3343 3357 3371 3385 3399
240 3414 3428 3442 3456 3470 3485 3499 3513 3527 3542
0-7
TEMPERATURE
Fahrenheit-Centigrade Conversion.
A simple way to convert a fahrenheit temperature reading into a centigrade temperature reading or vice verse
is to enter the accompanying table in the center or boldface column of figures.
These figures refer to the temperature in either Fahrenheit or Centigrade degrees.
If it is desired to convert from Fahrenheit to Centigrade degrees, consider the center column as a table of
Fahrenheit temperatures and read the corresponding Centigrade temperature in the column at the left.
If it is desired to convert from Centigrade to Fahrenheit degrees, consider the center column as a table of
Centigrade values, and read the corresponding Fahrenheit temperature on the right.
˚C ˚F ˚C ˚F ˚C ˚F ˚C ˚F
-40.4 -40 -40.0 -11.7 11 51.8 7.8 46 114.8 27.2 81 117.8
-37.2 -35 -31.0 -11.1 12 53.6 8.3 47 116.6 27.8 82 179.6
-34.4 -30 -22.0 -10.6 13 55.4 8.9 48 118.4 28.3 83 181.4
-31.7 -25 -13.0 -10.0 14 57.2 9.4 49 120.2 28.9 84 183.2
-28.9 -20 -4.0 -9.4 15 59.0 10.0 50 122.0 29.4 85 185.0
0-8
CONTENTS
SECTION 1 GENERAL
SECTION 6 TROUBLESHOOTING
13031GE01
13031GE02
1-1
PREPARE FOR EMERGENCIES
Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors,
ambulance ser vice, hospital, and fire
department near your telephone.
13031GE04
13031GE05
13031GE06
13031GE07
1-2
KEEP RIDERS OFF EXCAVATOR
Only allow the operator on the excavator. Keep
riders off.
Riders on excavator are subject to injury such
as being struck by foreign objects and being
thrown off the excavator. Riders also obstruct
the operator's view resulting in the excavator
being operated in an unsafe manner.
13031GE08
13031GE26
1-3
SUPPORT MACHINE PROPERLY
Always lower the attachment or implement to
the ground before you work on the machine. If
you must wor k on a lifted machine or
attachment, securely support the machine or
attachment.
Do not support the machine on cinder blocks,
hollow tiles, or props that may crumble under
13031GE10
continuous load.
Do not work under a machine that is supported
solely by a jack. Follow recommended
procedures in this manual.
13031GE11
13031GE12
13031GE13
1-4
BEWARE OF EXHAUST FUMES
Prevent asphyxiation. Engine exhaust fumes
can cause sickness or death.
If you must operate in a building, be positive
there is adequate ventilation. Either use an
exhaust pipe extension to remove the exhaust
fumes or open doors and windows to bring
enough outside air into the area.
REMOVE PAINT BEFORE WELDING OR
HEATING
Avoid potentially toxic fumes and dust.
Hazardous fumes can be generated when paint
is heated by welding, soldering, or using a torch.
Do all work outside or in a well ventilated area.
Dispose of paint and solvent properly.
Remove paint before welding or heating:
· If you sand or grind paint, avoid breathing the 13031GE14
dust.
Wear an approved respirator.
·If you use solvent or paint stripper, remove
stripper with soap and water before welding.
Remove solvent or paint stripper containers
and other flammable material from area.
Allow fumes to disperse at least 15 minutes
before welding or heating.
13031GE15
1-5
SERVICE MACHINE SAFELY
Tie long hair behind your head. Do not wear a
necktie, scarf, loose clothing or necklace when
you work near machine tools or moving parts.
If these items were to get caught, severe injury
could result.
Remove rings and other jewelry to prevent
electrical shorts and entanglement in moving
13031GE16
parts.
13031GE17
13031GE19
1-6
AVOID HEATING NEAR PRESSURIZED
FLUID LINES
Flammable spray can be generated by heating
near pressurized fluid lines, resulting in severe
burns to yourself and bystanders. Do not heat
by welding, soldering, or using a torch near
pressurized fluid lines or other flammable
materials.
13031GE20
Pressurized lines can be accidentally cut when
heat goes beyond the immediate flame area.
Install fire resisting guards to protect hoses or
other materials.
1-7
PREVENT ACID BURNS
Sulfuric acid in battery electrolyte is poisonous.
It is strong enough to burn skin, eat holes in
clothing, and cause blindness if splashed into
eyes.
Avoid the hazard by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
3. Avoiding breathing fumes when electrolyte
is added.
4. Avoiding spilling of dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize
the acid.
3. Flush your eyes with water for 10-15
minutes. Get medical attention immediate-
ly. 13031GE22
If acid is swallowed:
1. Drink large amounts of water or milk.
2. Then drink milk of magnesia, beaten eggs,
or vegetable oil.
3. Get medical attention immediately.
1-8
DISPOSE OF FLUIDS PROPERLY
Improperly disposing of fluids can harm the
environment and ecology. Before draining any
fluids, find out the proper way to dispose of
waste from your local environmental agency.
Use proper containers when draining fluids. Do
not use food or beverage containers that may
mislead someone into drinking from them.
DO NOT pour oil into the ground, down a drain,
or into a stream, pond, or lake. Observe 13031GE24
relevant environmental protection regulations
when disposing of oil, fuel, coolant, brake fluid,
filters, batteries, and other harmful waste.
13031GE25
1-9
GROUP 2 SPECIFICATIONS
1. MAJOR COMPONENT
Engine
Radiator
Oil cooler
Bucket cylinder Control link Idler Track roller Sprocket Dozer blade
Side cutter Control rod Track Carrier roller Travel motor Dozer blade cylinder
14092SP01
1-10
2. SPECIFICATIONS
1) R140LC-9S
·4.60
4.60 m (15' 1") BOOM and 2.50 m (8' 2") ARM
I(I') D
E
C
G
F
H
J M
K N
A B(L)
14092SP02
1-11
2) R140LC-9S, HYDRAULIC
HYDRAULIC ADJUSTABLE BOOM and 2.50 m (8' 2") ARM
I(I') D
E
C
G
F
H
J M
K N
A B(L)
14092SP03
1-12
3) R140LCD-9S
I(I') D
C
E
G
F
P
O
H
Q
J M
K N
A B(L)
14092SP04
1-13
4) R140LCM-9S
I(I') D
E
C
G
F
H
J M
K N
A B(L)
14092SP05
1-14
3. WORKING RANGE
1) R140LC/LCD-9S
(1) 4.60 m (15' 1") MONO BOOM
A
A'
F
D
B' E
C
B
8ft
14092SP06
Description 1.90 m (6' 3") Arm 2.10 m (6' 11") Arm ※2.50 m ( 8' 2") Arm 3.00 m ( 9' 10") Arm
Max digging reach A 7750 mm (25' 5") 7920 mm (25'11") 8340 mm (27' 4") 8800 mm (28'10")
Max digging reach on ground A' 7600 mm (24'11") 7780 mm (25' 6") 8200 mm (26'11") 8670 mm (28' 5")
Max digging depth B 5000 mm (16' 5") 5200 mm (17' 1") 5600 mm (18' 4") 6100 mm (20' 0")
Max digging depth (8ft level) B' 4730 mm (15' 6") 4950 mm (16' 3") 5390 mm (17' 8") 5910 mm (19' 5")
Max vertical wall digging depth C 4460 mm (14' 8") 4590 mm (15' 1") 5120 mm (16'10") 5660 mm (18' 7")
Max digging height D 8060 mm (26' 5") 8140 mm (26' 8") 8520 mm (27'11") 8730 mm (28' 8")
Max dumping height E 5630 mm (18' 6") 5710 mm (18' 9") 6080 mm (19'11") 6290 mm (20' 7")
Min swing radius F 2620 mm ( 8' 7") 2680 mm ( 8' 10") 2620 mm ( 8' 7") 2660 mm ( 8' 9")
87.3 [94.8] kN 87.3 [94.8] kN 87.3 [94.8] kN 87.3 [94.8] kN
SAE 8900 [9660] kgf 8900 [9660] kgf 8900 [9660] kgf 8900 [9660] kgf
19620 [21300] lbf 19620 [21300] lbf 19620 [21300] lbf 19620 [21300] lbf
Bucket digging force
102 [110.8] kN 102 [110.8] kN 102 [110.8] kN 102 [110.8] kN
ISO 10400 [11290] kgf 10400 [11290] kgf 10400 [11290] kgf 10400 [11290] kgf
22930 [24890] lbf 22930 [24890] lbf 22930[24890] lbf 22930 [24890] lbf
76.5 [83.1] kN 73.6 [79.9] kN 62.8 [68.2] kN 55.9 [60.7] kN
SAE 7800 [8470] kgf 7500 [8140] kgf 6400 [6950] kgf 5700 [6190] kgf
17200 [18670] lbf 16530 [17950] lbf 14110 [15320] lbf 12570 [13640] lbf
Arm crowd force
80.4 [87.3] kN 77.5 [84.1] kN 65.7 [71.4] kN 57.9 [62.8] kN
ISO 8200 [8900] kgf 7900 [8580] kgf 6700 [7270] kgf 5900 [6410] kgf
18080 [19630] lbf 17420 [18910] lbf 14770 [16040] lbf 13010 [14120] lbf
※ : STD [ ] : Power boost
1-15
(2) 4.10 m (13' 5") MONO BOOM
A
A'
F
D
B' E
C
B
8ft 14092SP06
1-16
(3) 4.90 m (16' 1") ADJUST BOOM
A
A'
F
D
E
C
B'
B
8ft 14092SP08
Description 1.90 m (6' 3") Arm 2.10 m (6' 11") Arm 2.50 m ( 8' 2") Arm
Max digging reach A 8140 mm (26' 8") 8310 mm (27' 3") 8720 mm (28' 7")
Max digging reach on ground A' 8000 mm (26' 3") 8180 mm (26'10") 8590 mm (28' 2")
Max digging depth B 5140 mm (16'10") 5340 mm (17' 6") 5740 mm (18'10")
Max digging depth (8ft level) B' 5020 mm (16' 6") 5220 mm (17' 2") 5630 mm (18' 6")
Max vertical wall digging depth C 4380 mm (14' 4") 4560 mm (15' 0") 5000 mm (16' 5")
Max digging height D 8770 mm (28' 9") 8870 mm (29' 21") 9230 mm (30' 3")
Max dumping height E 6280 mm (20' 7") 6390 mm (21' 0") 6740 mm (22' 1")
Min swing radius F 2660 mm ( 8' 9") 2800 mm ( 9' 2") 2670 mm ( 8' 9")
87.3 [94.8] kN 87.3 [94.8] kN 87.3 [94.8] kN
SAE 8900 [9660] kgf 8900 [9660] kgf 8900 [9660] kgf
19620 [21300] lbf 19620 [21300] lbf 19620 [21300] lbf
Bucket digging force
102 [110.8] kN 102 [110.8] kN 102 [110.8] kN
ISO 10400 [11290] kgf 10400 [11290] kgf 10400 [11290] kgf
22930 [24890] lbf 22930 [24890] lbf 22930[24890] lbf
76.5 [83.1] kN 73.6 [79.9] kN 62.8 [68.2] kN
SAE 7800 [8470] kgf 7500 [8140] kgf 6400 [6950] kgf
17200 [18670] lbf 16530 [17950] lbf 14110 [15320] lbf
Arm crowd force
80.4 [87.3] kN 77.5 [84.1] kN 65.7 [71.4] kN
ISO 8200 [8900] kgf 7900 [8580] kgf 6700 [7270] kgf
18080 [19630] lbf 17420 [18910] lbf 14770 [16040] lbf
[ ] : Power boost
1-17
2) R140LCM-9S
(1) 4.6 m (15' 1") MONO BOOM
A
A'
F
D
B' E
C
B
8ft 14092SP09
Description 1.90 m (6' 3") Arm 2.10 m (6' 11") Arm ※2.50 m ( 8' 2") Arm 3.00 m ( 9' 10") Arm
Max digging reach A 7750 mm (25' 5") 7920 mm (26' 0") 8340 mm (27' 4") 8800 (28'10")
Max digging reach on ground A' 7540 mm (24' 9") 7720 mm (25' 4") 8130 mm (26' 8") 8600 (28' 3")
Max digging depth B 4700 mm (15' 5") 4900 mm (16' 1") 5300 mm (17' 5") 5800 (19' 0")
Max digging depth (8ft level) B' 4440 mm (14' 7") 4650 mm (15' 3") 5100 mm (16' 9") 5620 (18' 5")
Max vertical wall digging depth C 4180 mm (13' 9") 4310 mm (14' 2") 4840 mm (15'11") 5380 (17' 8")
Max digging height D 8340 mm (27' 4") 8410 mm (27' 7") 8740 mm (28' 8") 9010 (29' 7")
Max dumping height E 5900 mm (19' 4") 5980 mm (19' 7") 6300 mm (20' 8") 6560 (21' 6")
Min swing radius F 2620 mm ( 8' 7") 2680 mm ( 8'10") 2620 mm ( 8' 7") 2660 ( 8' 9")
87.3 [94.8] kN 87.3 [94.8] kN 87.3 [94.8] kN 87.3 [94.8] kN
SAE 8900 [9660] kgf 8900 [9660] kgf 8900 [9660] kgf 8900 [9660] kgf
19620 [21300] lbf 19620 [21300] lbf 19620 [21300] lbf 19620 [21300] lbf
Bucket digging force
102 [110.8] kN 102 [110.8] kN 102 [110.8] kN 102 [110.8] kN
ISO 10400 [11290] kgf 10400 [11290] kgf 10400 [11290] kgf 10400 [11290] kgf
22930 [24890] lbf 22930 [24890] lbf 22930[24890] lbf 22930 [24890] lbf
76.5 [83.1] kN 73.6 [79.9] kN 62.8 [68.2] kN 55.9 [60.7] kN
SAE 7800 [8470] kgf 7500 [8140] kgf 6400 [6950] kgf 5700 [6190] kgf
17200 [18670] lbf 16530 [17950] lbf 14110 [15320] lbf 12570 [13640] lbf
Arm crowd force
80.4 [87.3] kN 77.5 [84.1] kN 65.7 [71.4] kN 57.9 [62.8] kN
ISO 8200 [8900] kgf 7900 [8580] kgf 6700 [7270] kgf 5900 [6410] kgf
18080 [19630] lbf 17420 [18910] lbf 14770 [16040] lbf 13010 [14120] lbf
※ : STD [ ] : Power boost
1-18
4. WEIGHT
1) R140LC-9S, R140LCD-9S
R140LC-9S R140LCD-9S
Item
kg lb kg lb
Upper structure assembly 5630 12420 ←
Main frame weld assembly 1160 2560 ←
Engine assembly 330 730 ←
Main pump assembly 100 220 ←
Main control valve assembly 140 310 ←
Swing motor assembly 120 260 ←
Hydraulic oil tank assembly 160 350 ←
Fuel tank assembly 130 290 ←
Counterweight 2000 4410 ←
Cab assembly 440 970 ←
Lower chassis assembly 5340 11760 6160 13580
Track frame weld assembly 1590 3510 1840 4060
Swing bearing 190 410 ←
Travel motor assembly 480 1060 ←
Turning joint 50 110 ←
Track recoil spring 210 460 ←
Idler 250 550 ←
Carrier roller 40 90 ←
Track roller 490 1080 ←
Track-chain assembly (600 mm standard triple grouser shoe) 1010 2230 ←
Dozer blade assembly - 550 1220
Front attachment assembly (4.6 m boom, 2.5 m arm,
2420 5330 ←
0.58 m3 SAE heaped bucket)
4.6 m boom assembly 830 1830 ←
2.5 m arm assembly 435 960 ←
0.58 m3 SAE heaped bucket 480 1060 ←
Boom cylinder assembly 130 290 ←
Arm cylinder assembly 160 350 ←
Bucket cylinder assembly 100 220 ←
Bucket control rod assembly 90 200 ←
Dozer blade cylinder assembly - 55 120
1-19
2) R140LCM-9S
R140LCM-9S
Item
kg lb
Upper structure assembly 5630 12420
Main frame weld assembly 1160 2560
Engine assembly 330 730
Main pump assembly 100 220
Main control valve assembly 140 310
Swing motor assembly 120 260
Hydraulic oil tank assembly 160 350
Fuel tank assembly 130 290
Counterweight 2000 4410
Cab assembly 440 970
Lower chassis assembly 8700 19180
Track frame weld assembly 2180 4810
Swing bearing 190 410
Travel motor assembly 305 670
Turning joint 50 110
Tension cylinder assembly 280 620
Idler assembly 320 710
Carrier roller assembly 200 440
Track roller assembly 700 1540
Track-chain assembly (800 mm standard triple grouser shoe) 1370 3020
Front attachment assembly (4.6 m boom, 2.5 m arm,
2420 5330
0.58 m3 SAE heaped bucket)
4.6 m boom assembly 830 1830
2.5 m arm assembly 435 960
0.58 m3 SAE heaped bucket 480 1060
Boom cylinder assembly 130 290
Arm cylinder assembly 160 350
Bucket cylinder assembly 100 220
Bucket control rod assembly 90 200
1-20
5. LIFTING CAPACITIES
1) R140LC-9S
(1) 4.60 m (15' 1") boom, 2.50 m (8' 2") arm equipped with 0.58 m3 (SAE heaped) bucket and 600
mm (24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
(2) 4.60 m (15' 1") boom, 1.90 m (6' 3") arm equipped with 0.58 m3 (SAE heaped) bucket and 600 mm
(24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
Load radius At max. reach
Load point 1.5 m (5 ft) 3.0 m (10 ft) 4.5 m (15 ft) 6.0 m (20 ft) Capacity Reach
height
m (ft)
6.0 m kg *3340 *3340 *3170 2350 5.95
(20.0 ft) lb *7360 *7360 *6990 5180 (19.5)
4.5 m kg *3550 *3550 2820 1760 6.90
(15.0 ft) lb *7830 *7830 6220 3880 (22.6)
3.0 m kg *6270 *6270 *4440 3510 3480 2170 2480 1520 7.37
(10.0 ft) lb *13820 *13820 *9790 7740 7670 4780 5470 3350 (24.2)
1.5 m kg *8490 6040 5400 3270 3380 2080 2390 1450 7.45
(5.0 ft) lb *18720 13320 11900 7210 7450 4590 5270 3200 (24.4)
Ground kg *8230 5790 5200 3100 3300 2000 2510 1520 7.17
Line lb *18140 12760 11460 6830 7280 4410 5530 3350 (23.5)
-1.5 m kg *6670 *6670 *9690 5800 5140 3050 2960 1810 6.48
(-5.0 ft) lb *14700 *14700 *21360 12790 11330 6720 6530 3990 (21.3)
-3.0 m kg *10970 *10970 *8330 5930 5220 3110 *3690 2670 5.15
(-10 ft) lb *24180 *24180 *18360 13070 11510 6860 *8140 5890 (16.9)
1-21
2) R140LC-9S, ADJUST BOOM
(1) 4.90 m (16' 1") adjust boom, 1.90 m (6' 3") arm equipped with 0.58 m3 (SAE heaped) bucket and
600 mm (24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
(2) 4.90 m (16' 1") adjust boom, 2.10 m (6' 11") arm equipped with 0.58 m3 (SAE heaped) bucket and
600 mm (24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
Load radius At max. reach
Load point 3.0 m (10 ft) 4.5 m (15 ft) 6.0 m (20 ft) Capacity Reach
height
m (ft)
6.0 m kg *2690 *2690 *2760 1900 6.68
(20.0 ft) lb *5930 *5930 *6080 4190 (21.9)
4.5 m kg *3080 *3080 *2990 2230 2420 1470 7.52
(15.0 ft) lb *6790 *6790 *6590 4920 5340 3240 (24.7)
3.0 m kg *5930 *5930 *4030 3460 *3360 2140 2150 1280 7.94
(10.0 ft) lb *13070 *13070 *8880 7630 *7410 4720 4740 2820 (26.0)
1.5 m kg *5140 3160 3340 2010 2080 1220 8.02
(5.0 ft) lb *11330 6970 7360 4430 4590 2690 (26.3)
Ground kg *5690 5540 5090 2960 3230 1910 2170 1270 7.77
Line lb *12540 12210 11220 6530 7120 4210 4780 2800 (25.5)
-1.5 m kg *8930 5560 5020 2900 3190 1870 2490 1470 7.14
(-5.0 ft) lb *19690 12260 11070 6390 7030 4120 5490 3240 (23.4)
-3.0 m kg *8650 5690 5070 2950
(-10 ft) lb *19070 12540 11180 6500
1-22
3) R140LCD-9S
(1) 4.60 m (15' 1") boom, 1.9 m (6' 3") arm equipped with 0.58 m3 (SAE heaped) bucket and 600 mm
(24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
(2) 4.60 m (15' 1") boom, 2.50 m (8' 2") arm equipped with 0.58 m3 (SAE heaped) bucket and 600 mm
(24") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
Load radius At max. reach
Load point 1.5 m (5 ft) 3.0 m (10 ft) 4.5 m (15 ft) 6.0 m (20 ft) Capacity Reach
height
m (ft)
6.0 m kg *2810 2040 6.69
(20.0 ft) lb *6190 4500 (21.9)
4.5 m kg *2770 2410 2660 1600 7.53
(15.0 ft) lb *6110 5310 5860 3530 (24.7)
3.0 m kg *4930 *4930 *3830 3770 *3380 2320 2380 1400 7.95
(10.0 ft) lb *10870 *10870 *8440 8310 *7450 5110 5250 3090 (26.1)
1.5 m kg *8030 6580 *5010 3490 3680 2210 2300 1340 8.03
(5.0 ft) lb *17700 14510 *11050 7690 8110 4870 5070 2950 (26.3)
Ground kg *8780 6140 5640 3280 3570 2110 2400 1400 7.77
Line lb *19360 13540 12430 7230 7870 4650 5290 3090 (25.5)
-1.5 m kg *5740 *5740 *9910 6040 5530 3180 3510 2060 2730 1610 7.15
(-5.0 ft) lb *12650 *12650 *21850 13320 12190 7010 7740 4540 6020 3550 (23.5)
-3.0 m kg *8760 *8760 *9040 6110 5550 3200 *3540 2170 6.01
(-10 ft) lb *19310 *19310 *19930 13470 12240 7050 *7800 4780 (19.7)
-4.5 m kg *6590 6370
(-15 ft) lb *14530 14040
1-23
4) R140LCM-9S
(1) 4.60 m (15' 1") boom, 1.90 m (6' 3") arm equipped with 0.58 m3 (SAE heaped) bucket and 800 mm
(32") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
(2) 4.60 m (15' 1") boom, 2.50 m (8' 2") arm equipped with 0.58 m3 (SAE heaped) bucket and 800 mm
(32") triple grouser shoe and 2000 kg (4410 Ib) counterweight.
Load radius At max. reach
Load point 1.5 m (5 ft) 3.0 m (10 ft) 4.5 m (15 ft) 6.0 m (20 ft) Capacity Reach
height
m (ft)
6.0 m kg *2830 2180 6.87
(20.0 ft) lb *6240 4810 (22.5)
4.5 m kg *3040 *3040 *2930 2690 2790 1770 7.63
(15.0 ft) lb *6700 *6700 *6460 5930 6150 3900 (25.0)
3.0 m kg *5460 *5460 *4030 *4030 *3470 2590 2540 1590 7.99
(10.0 ft) lb *12040 *12040 *8880 *8880 *7650 5710 5600 3510 (26.2)
1.5 m kg *8460 7290 *5200 3880 3930 2480 2490 1540 8.01
(5.0 ft) lb *18650 16070 *11460 8550 8660 5470 5490 3400 (26.3)
Ground kg *3600 *3600 *8880 6920 6030 3680 3820 2380 2630 1630 7.70
Line lb *7940 *7940 *19580 15260 13290 8110 8420 5250 5800 3590 (25.3)
-1.5 m kg *6200 *6200 *9840 6850 5940 3600 3780 2340 3050 1900 7.00
(-5.0 ft) lb *13670 *13670 *21690 15100 13100 7940 8330 5160 6720 4190 (23.0)
-3.0 m kg *9390 *9390 *8770 6960 *5760 3640 *3520 2650 5.74
(-10 ft) lb *20700 *20700 *19330 15340 *12700 8020 *7760 5840 (18.8)
1-24
6. BUCKET SELECTION GUIDE
1) R140LC-9S, R140LCD-9S
(1) General bucket
0.23 m3 SAE 0.40, 0.46 m3 SAE 0.52, ※0.58, 0.65, 0.71 m3 SAE
heaped bucket heaped bucket heaped bucket
Recommendation
Capacity Width
4.6 m (15' 1") boom 4.1 m (13' 5") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm 3.0 m arm 1.9 m arm 2.1 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2") (9' 10") (6' 3") (6' 11")
※ : Standard bucket
Applicable for materials with density of 2000 kg/m3 (3370 lb/yd3) or less
Applicable for materials with density of 1600 kg/m3 (2700 lb/yd3) or less
Applicable for materials with density of 1100 kg/m3 (1850 lb/yd3) or less
1-25
(2) Special bucket
Ditch cleaning bucket Slope finishing bucket
Recommendation
Capacity Width
4.6 m (15' 1") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm 3.0 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2") (9' 10")
Applicable for materials with density of 2000 kgf/m3 (3370 lbf/yd3) or less
Applicable for materials with density of 1600 kgf/m3 (2700 lbf/yd3) or less
Applicable for materials with density of 1100 kgf/m3 (1850 lbf/yd3) or less
1-26
2) R140LC-9S, ADJUST BOOM
(1) General bucket
0.23 m3 SAE 0.40, 0.46 m3 SAE 0.52, ※0.58, 0.65, 0.71 m3 SAE
heaped bucket heaped bucket heaped bucket
Recommendation
Capacity Width
4.9 m (16' 1") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2")
※ : Standard bucket
Applicable for materials with density of 2000 kg/m3 (3370 lb/yd3) or less
Applicable for materials with density of 1600 kg/m3 (2700 lb/yd3) or less
Applicable for materials with density of 1100 kg/m3 (1850 lb/yd3) or less
1-27
(2) Special bucket
Ditch cleaning bucket Slope finishing bucket
Recommendation
Capacity Width
4.9 m (16' 1") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2")
Applicable for materials with density of 2000 kgf/m3 (3370 lbf/yd3) or less
Applicable for materials with density of 1600 kgf/m3 (2700 lbf/yd3) or less
Applicable for materials with density of 1100 kgf/m3 (1850 lbf/yd3) or less
1-28
3) R140LCM-9S
(1) General bucket
0.23 m3 SAE 0.40, 0.46 m3 SAE 0.52, ※0.58, 0.65, 0.71 m3 SAE
heaped bucket heaped bucket heaped bucket
Recommendation
Capacity Width
4.6 m (15' 1") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm 3.0 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2") (9' 10")
※ : Standard bucket
Applicable for materials with density of 2000 kg/m3 (3370 lb/yd3) or less
Applicable for materials with density of 1600 kg/m3 (2700 lb/yd3) or less
Applicable for materials with density of 1100 kg/m3 (1850 lb/yd3) or less
1-29
(2) Special bucket
Ditch cleaning bucket Slope finishing bucket
Recommendation
Capacity Width
4.9 m (16' 1") boom
Weight
SAE CECE Without With 1.9 m arm 2.1 m arm 2.5 m arm
heaped heaped side cutter side cutter (6' 3") (6' 11") (8' 2")
Applicable for materials with density of 2000 kgf/m3 (3370 lbf/yd3) or less
Applicable for materials with density of 1600 kgf/m3 (2700 lbf/yd3) or less
Applicable for materials with density of 1100 kgf/m3 (1850 lbf/yd3) or less
1-30
7. UNDERCARRIAGE
1) TRACKS
X-leg type center frame is integrally welded with reinforced box-section track frames. The design
includes dry tracks, lubricated rollers, idlers, sprockets, hydraulic track adjusters with shock
absorbing springs and assembled track-type tractor shoes with triple grousers.
2) TYPES OF SHOES
Triple grouser
Model Shapes
1-31
4) SELECTION OF TRACK SHOE
Suitable track shoes should be selected according to operating conditions.
Method of selecting shoes
Confirm the category from the list of applications in table 22, then use table 1 to select the shoe.
Wide shoes (Categories B and C) have limitations on applications. Before using wide shoes, check
the precautions, then investigate and study the operating conditions to confirm if these shoes are
suitable.
Select the narrowest shoe possible to meet the required flotation and ground pressure.
Application of wider shoes than recommendations will cause unexpected problem such as bending
of shoes, crack of link, breakage of pin, loosening of shoe bolts and the other various problems.
※ Table 1
Track shoe Specification Category
600 mm triple grouser Standard A
500 mm triple grouser Option A
700 mm triple grouser Option B
710 mm triple grouser R140LC-9S only B
800 mm triple grouser R140LCM-9S only B
※ Table 2
Category Applications Applications
Rocky ground, · Travel at low speed on rough ground with large obstacles such as
A river beds, boulders or fallen trees
normal soil
Normal soil, · These shoes cannot be used on rough ground with large obstacles such
soft ground as boulders or fallen trees
B
· Travel at high speed only on flat ground
· Travel slowly at low speed if it is impossible to avoid going over obstacles
1-32
8. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE
Item Specification
Model Cummins B3.9-C
Type 4-cycle turbocharged charge air cooled diesel engine
Cooling method Water cooling
Number of cylinders and arrangement 4 cylinders, in-line
Firing order 1-3-4-2
Combustion chamber type Direct injection type
Cylinder bore×stroke 102×120 mm
Piston displacement 3900cc (238cu in)
Compression ratio 18 : 1
Rated gross horse power (SAE J1995) 105 Hp (78 kW) at 2000 rpm
Maximum torque 45.6 kgf·m (330 lbf·ft) at 1500 rpm
Engine oil quantity 15.3ℓ (4.0 U.S. gal)
Dry weight 320 kg (705 lb)
High idling speed 2350±50 rpm
Low idling speed 850±100 rpm
Rated fuel consumption 160 g/Hp·hr at 2100 rpm
Starting motor 24 V-4.5 kW
Alternator 24 V-50 A
Battery 2×12 V×80 Ah
2) MAIN PUMP
Item Specification
Type Variable displacement tandem axis piston pumps
Capacity 2×65 cc/rev
Maximum pressure 350 kgf/cm2 (4980 psi) [380 kgf/cm2 (5400 psi)]
Rated oil flow 2×123.5ℓ/min (32.6 U.S. gpm / 27.2 U.K. gpm)
Rated speed 2000 rpm
[ ]: Power boost
1-33
3) GEAR PUMP
Item Specification
Type Fixed displacement gear pump single stage
Capacity 15cc/rev
Maximum pressure 40 kgf/cm2 (570 psi)
Rated oil flow 28.5ℓ/min (7.5 U.S. gpm / 6.3 U.K. gpm)
5) SWING MOTOR
Item Specification
Type Fixed displacement axial piston motor
Capacity 72 cc/rev
Relief pressure 265 kgf/cm2 (3770psi)
Braking system Automatic, spring applied hydraulic released
Braking torque Minimum 30 kgf·m (217 lbf·ft)
Brake release pressure 15~50 kgf/cm2 (213~711 psi)
Reduction gear type 2 - stage planetary
6) TRAVEL MOTOR
Item Specification
Type Variable displacement axial piston motor
Relief pressure 350 kgf/cm2 (4980 psi)
Capacity (max / min) 77/45 cc/rev
Reduction gear type 2-stage planetary
Braking system Automatic, spring applied hydraulic released
Brake release pressure 9.5 kgf/cm2 (135 psi)
Braking torque 40.6 kgf·m (294 lbf·ft)
1-34
7) CYLINDER
Item Specification
Bore dia×Rod dia×Stroke Ø105×Ø75×1075 mm
Boom cylinder
Cushion Extend only
Bore dia×Rod dia×Stroke Ø115×Ø80×1138 mm
Arm cylinder
Cushion Extend and retract
Bore dia×Rod dia×Stroke Ø100×Ø70×837 mm
Bucket cylinder
Cushion Extend only
Bore dia×Rod dia×Stroke Ø100×Ø65×236 mm
Dozer cylinder (opt)
Cushion -
Bore dia×Rod dia×Stroke Ø145×Ø90×613 mm
Adjust cylinder (opt)
Cushion Extend only
Bore dia×Rod dia×Stroke Ø105×Ø75×975 mm
Adjust boom cylinder (opt)
Cushion Extend only
※ Discoloration of cylinder rod can occur when the friction reduction additive of lubrication oil spreads on
the rod surface.
※ Discoloration does not cause any harmful effect on the cylinder performance.
8) SHOE
Item Width Ground pressure Link quantity Overall width
Standard 600 mm (24") 0.36 kgf/cm2 (5.12 psi) 46 2600 mm ( 8' 6")
R140LC-9S 500 mm (20") 0.43 kgf/cm2 (6.11 psi) 46 2500 mm ( 8' 2")
Option
700 mm (28") 0.31 kgf/cm (4.41 psi)
2 46 2700 mm ( 8' 10")
Standard 600 mm (24") 0.38 kgf/cm2 (5.40 psi) 46 2600 mm ( 8' 6")
R140LCD-9S 500 mm (20") 0.45 kgf/cm2 (6.40 psi) 46 2500 mm ( 8' 2")
Option
700 mm (28") 0.33 kgf/cm2 (4.70 psi) 46 2700 mm ( 8' 10")
Standard 800 mm (32") 0.32 kgf/cm (4.55 psi)
2 47 2910 mm ( 9' 7")
R140LCM-9S
Option 710mm (28") 0.32 kgf/cm2 (4.55 psi) 46 2820 mm ( 9' 3")
9) BUCKET
Capacity Tooth Width
Item
SAE heaped CECE heaped quantity Without side cutter With side cutter
Standard ※0.58 m3 (0.76 yd3) 0.50 m3 (0.65 yd3) 5 1000 mm (39.4") 1100 mm (43.3")
0.23 m (0.30 yd )
3 3 0.20 m (0.26 yd )
3 3 3 520 mm (20.5") 620 mm (24.4")
0.40 m3 (0.52 yd3) 0.35 m3 (0.46 yd3) 4 750 mm (29.5") 850 mm (33.5")
0.46 m3 (0.60 yd3) 0.40 m3 (0.52 yd3) 4 840 mm (33.1") 940 mm (37.0")
R140LC-9S 0.52 m3 (0.68 yd3) 0.45 m3 (0.59 yd3) 5 915 mm (36.0") 1015 mm (40.0")
Option
0.65 m (0.85 yd )
3 3 0.55 m (0.72 yd )
3 3 5 1105 mm (43.5") 1205 mm (47.4")
0.71 m3 (0.93 yd3) 0.60 m3 (0.78 yd3) 5 1190 mm (46.9") 1290 mm (50.8")
★0.45 m3 (0.59 yd3) 0.40 m3 (0.52 yd3) - 1520 mm (59.8") -
⊙0.55 m3 (0.72 yd3) 0.45 m3 (0.59 yd3) - 1800 mm (70.9") -
★ : Ditch cleaning bucket
⊙ : Slope finishing bucket
1-35
9. RECOMMENDED OILS
SAE 30
SAE 10W
Engine oil pan Engine oil 15.3 (4.0)
SAE 10W-30
SAE 15W-40
NLGI NO.1
Swing drive Grease 0.35 (0.09)
NLGI NO.2
ISO VG 32
Tank:
124 (32.8)
Hydraulic tank Hydraulic oil ISO VG 46
System:
210 (55.5)
ISO VG 68
NLGI NO.1
Fitting
Grease As required
(Grease nipple) NLGI NO.2
Mixture of
Radiator antifreeze
17 (4.5) Ethylene glycol base permanent type
(Reservoir tank) and water
50 : 50
1-36
SECTION 2 STRUCTURE AND FUNCTION
Group 1
Pump Device ------------------------------------------------------------------------------------------------------ 2-1
Group 2
Main Control Valve --------------------------------------------------------------------------------------------- 2-19
Group 3
Swing Device ------------------------------------------------------------------------------------------------------ 2-46
Group 4
Travel Device ------------------------------------------------------------------------------------------------------ 2-58
Group 5 RCV Lever ---------------------------------------------------------------------------------------------------------- 2-68
Group 6 RCV Pedal ---------------------------------------------------------------------------------------------------------- 2-75
SECTION 2 STRUCTURE AND FUNCTION
GROUP 1 PUMP DEVICE
1. STRUCTURE
The pump device consists of main pump, regulator and gear pump.
B3
Dr Pi2
B1
Pi1 Pi2 A2
A1
VIEW A
Dr
B3
B1
a4
14092MP01
A
2-1
1) MAIN PUMP (1/2)
The main pump consists of two piston pumps (front & rear) and valve block.
548
535 789 732 532 531 214 702 792 901 711 312 719 124 151 152 113 406
808 534 808
953 724 954
886
717
406 04
774
111
261 262
127 406
123
710
824
251
490 212 211 153 156 157 467 313 468 466 116 885 314 141 981 271 401
728 727 725 983
14092MP02
2-2
2) REGULATOR (1/2)
C
615 Pi
613
875
611
A
B
641 730 643 708 644 645 646 728 924 801
SECTION B-B
438
Pi Pi
656
722 D
14092MP04
KR38-9N62 (FRONT) A
079 735 722 466 KR38-9N61 (REAR)
2-3
REGULATOR (2/2)
655 734 653 654 836 651 652 601 624 629 630 628 802
641
814
898
631
732
733
622
2-4
3) GEAR PUMP
B3
434
311
A3
312
850
732
a3 355
710 435 361 353 307 310 308 309 434 466,725
14092MP06
2-5
2. FUNCTION
1) MAIN PUMP
The pumps may classified roughly into the rotary group performing a rotary motion and working as
the major part of the whole pump function: the swash plate group that varies the delivery rates: and
the valve cover group that changes over oil suction and discharge.
2507A2MP14
2-6
(3) Valve block group
The valve block group consists of valve
block (312), valve plate (313) and valve
plate pin(885).
The valve plate having two melon-shaped
312
ports is fixed to the valve block and feeds
and collects oil to and from the cylinder 313
block.
The oil changed over by the valve plate is
connected to an external pipeline by way 885
of the valve block.
Now, if the drive shaft is driven by a prime
21092MP07
mover (electric motor, engine, etc), it
rotates the cylinder block via a spline
linkage at the same time. If the swash
plate is tilted as in Fig (previous page) the
pistons arranged in the cylinder block
make a reciprocating motion with respect
to the cylinder block, while they revolve
with the cylinder block.
If you pay attention to a single piston, it
performs a motion away from the valve
plate (oil sucking process) within 180
degrees, and makes a motion towards the
valve plate (or oil discharging process) in
the rest of 180 degrees. When the
swash plate has a tilting angle of zero, the
piston makes no stroke and discharges
no oil.
2-7
2) REGULATOR
Regulator consists of the negative flow control, total horse power control and power shift control
function.
Delivery flow, Q
control in which the delivery flow Q
decreases as the pilot pressure Pi rises.
With this mechanism, when the pilot
pressure corresponding to the flow
required for the work is commanded, the
pump discharges the required flow only,
and so it does not consume the power Pilot pressure, Pi
uselessly.
2-8
① Flow reducing function
P1 CL
B(E)
874
897
C
Pi(From MCV)
A
875
611
D 531
14W92MP12
As the pilot pressure Pi rises, the pilot piston (643) moves to the right to a position where the
force of the pilot spring (646) balances with the hydraulic force.
The groove (A) in the pilot piston is fitted with the pin (875) that is fixed to lever 2 (613).
Therefore, when the pilot piston moves, lever 2 rotates around the fulcrum of point B [fixed by
the fulcrum plug (614) and pin (875)]. Since the large hole section (C) of lever 2 contains a
protruding pin (897) fixed to the feedback lever (611), the pin (897) moves to the right as lever 2
rotates. Since the opposing-flat section (D) of the feedback lever is fitted with the pin (548) fixed
by the tilting pin (531) that swings the swash plate, the feedback lever rotates around the fulcrum
of point D, as the pin (897) moves.
Since the feedback lever is connected with the spool (652) via the pin (874), the spool moves to
the right.
The movement of the spool causes the delivery pressure P1 to connect to port CL through the
spool and to be admitted to the large diameter section of the servo piston. The delivery pressure
P1 that is constantly admitted to the small diameter section of the servo piston moves the servo
piston to the right due to the area difference, resulting in decrease of the tilting angle.
When the servo piston moves to the right, point D also moves to the right. The spool is fitted
with the return spring (654) and is tensioned to the left at all times, and so the pin (897) is
pressed against the large hole section (C) of lever 2.
Therefore, as point D moves, the feedback lever rotates around the fulcrum of point C, and the
spool is shifted to the left. This causes the opening between the sleeve (651) and spool (652) to
close slowly, and the servo piston comes to a complete stop when it closes completely.
2-9
② Flow increasing function
P1 CL
B(E)
874
897
C
Pi(From MCV)
A
875
611
D 531
14W92MP13
As the pilot pressure Pi decreases, the pilot piston (643) moves to the left by the action of the
pilot spring (646) and causes lever 2 (613) to rotate around the fulcrum of point B. Since the pin
(897) is pressed against the large hole section (C) of lever 2 by the action of the return spring
(654) via the spool (652), pin (874), and feedback lever (611), the feedback lever rotates around
the fulcrum of point D as lever 2 rotates, and shifts the spool to the left. Port CL opens a way to
the tank port as the spool moves. This deprives the large diameter section of the servo piston of
pressure, and shifts the servo piston to the left by the discharge pressure P1 in the small
diameter section, resulting in an increase in the flow rate.
As the servo piston moves, point D also moves to the left, the feedback lever rotates around the
fulcrum of point C, and the spool moves to the right till the opening between the spool and sleeve
is closed.
2-10
③ Adjustment of flow control characteristic
The flow control characteristic can be
adjusted with the adjusting screw.
Adjust it by loosening the hexagon nut 801
(801) and by tightening (or loosening) the 924
hexagonal socket head screw (924).
Tightening the screw shifts the control
chart to the right as shown in the figure.
※ Adjusting value
Adjustment of flow control
Speed characteristic
Tightening Flow control Flow change
amount of starting amount
adjusting pressure
screw (924) change
amount
Delivery flow, Q
(min -1) (Turn) (kgf/cm2) (ℓ/min)
Pilot pressure, Pi
21092MP11
2-11
(2) Total horsepower control
The regulator decreases the pump tilting
angle (delivery flow) automatically to limit
the input torque within a certain value with
Delivery flow, Q
a rise in the delivery pressure P1 of the
self pump and the delivery pressure P2 of
the companion pump.
(The input horsepower is constant when
the speed is constant.)
Since the regulator is of the simultaneous
Delivery pressure, (P1+P2)
total horsepower type that operates by the
sum of load pressures of the two pumps
in the tandem double-pump system, the
prime mover is automatically prevented
from being overloaded, irrespective of the
load condition of the two pumps, when
horsepower control is under way.
Since this regulator is of the simultaneous
total horsepower type, it controls the tilting
angles (displacement volumes) of the two
pumps to the same value as represented
by the following equation :
Tin = P1×q/2Л + P2×q/2Л
= (P1+P2)×q/2Л
The horsepower control function is the
same as the flow control function and is
summarized in the following. (For detailed
behaviors of respective parts, refer to the
section of flow control).
2-12
① Overload preventive function
P1 CL
B(E)
897
P2 P1
875
611
14W92RG03
When the self pump delivery pressure P1 or the companion pump delivery pressure P2 rises, it
acts on the stepped part of the compensating piston (621). It presses the compensating rod
(623) to the right till the force of the outer spring (625) and inner spring (626) balances with the
hydraulic force. The movement of the compensating rod is transmitted to lever 1 (612) via pin
(875).
Lever 1 rotates around the pin (875) (E) fixed to the casing (601).
Since the large hole section (F) of lever 1 contains a protruding pin (897) fixed to the feedback
lever (611), the feedback lever rotates around the fulcrum of point D as lever 1 rotates, and then
the spool (652) is shifted to the right. As the spool moves, the delivery pressure P1 is admitted
to the large diameter section of the servo piston via port CL, causes the servo piston move to the
right, reduces the pump delivery, flow rate, and prevents the prime mover from being overloaded.
The movement of the servo piston is transmitted to the feedback lever via point D. Then the
feedback lever rotates around the fulcrum of point F and the spool is shifted to the left. The
spool moves till the opening between the spool (652) and sleeve (651) is closed.
2-13
② Flow reset function
P1 CL
B(E)
897
P2 P1
875
611
14W92RG04
As the self pump delivery pressure P1 or the companion pump delivery pressure P2 decreases,
the compensating rod (623) is pushed back by the action of the springs (625 & 626) to rotate
lever 1 (612) around point E. Rotating of lever 1 causes the feedback lever (611) to rotate
around the fulcrum of point D and then the spool (652) to move to the left. As a result, port CL
opens a way to the tank port.
This causes the servo piston to move to the left and the pump's delivery rate to increase.
The movement of the servo piston is transmitted to the spool by the action of the feedback
mechanism to move it till the opening between the spool and sleeve is closed.
2-14
③ Low tilting angle (low flow) command preferential function
As mentioned above, flow control and horsepower control tilting angle commands are
transmitted to the feedback lever and spool via the large-hole sections (C & F) of levers 1 and 2.
However, since sections C and F have the pins (Ø4) protruding from the large hole (Ø8), only
the lever lessening the tilting angle contacts the pin (897) ; the hole (Ø8) in the lever of a larger
tilting angle command is freed without contacting the pin (897). Such a mechanical selection
method permits preference of the lower tilting angle command of the flow control and horsepower
control.
④ Adjustment of input horsepower
Since the regulator is of total cumulative horsepower type, adjust the adjusting screws of both
the front and rear pumps, when changing the horsepower set values. The pressure change
values by adjustment are based on two pumps pressurized at the same time, and the values will
be doubled when only one pump is loaded.
2-15
b. Adjustment of inner spring
625 626 630 628
Adjust it by loosening the hexagon nut
(802) and by tightening (or loosening)
the adjusting stem C (627).
Tightening the screw increases the flow
and then the input horsepower as
shown in the figure.
※ Adjusting value
Delivery flow, Q
(min -1) (Turn) (ℓ/min) (kgf·m)
2-16
(3) Power shift control
898
P1 CL
B(E)
897
P2 P1
875
611
14W92RG05
2-17
(4) Adjustment of maximum and minimum flows
① Adjustment of maximum flow
Adjust it by loosening the hexagon nut 954 808
(808) and by tightening (or loosening)
the set screw (954).
The maximum flow only is adjusted
without changing other control
characteristics.
14W92MP23
Speed Adjustment of max flow
Tightening Flow change
amount of amount
Delivery flow, Q
adjusting screw
(954)
Delivery pressure, Pn
2-18
GROUP 2 MAIN CONTROL VALVE
2-19
51 53 56 69 3 77 34 65 62 31 49 48 69 46 47 50 56 53 61 30 50 53 56 69 11 43 79 72 28 63 29 80 44 26 62 69 31 25 62 31 62 31
1 Housing-P1 43 Load check-poppet
2 Housing-P2 44 Load check-poppet
A A
3 Spool-straight travel 45 Signal-poppet
B B
4 Spool-travel (LH, RH) 46 Travel straight-sleeve
6 Spool-swing 47 Travel straight-piston
C C 7 Spool-boom 1 48 Orifice signal
8 Spool-swing priority 49 Coin type filter
D D 9 Spool-boom 2 50 Pilot cap
10 Spool-arm 2 51 Pilot cap
E E 11 Spool-arm 1 52 Pilot cap
31 62 43 79 72 28 72 28 79 43 16 42 27 69 59 41 42 67 32 72 28 79 43 29 63 80 4412 69 56 53 51 12 Spool-arm regeneration 53 Socket bolt
A-A (STRAIGHT TRAVEL & SUPPLY) F F 13 Spool-option B 54 Socket bolt
E-E (ARM 1 & ARM REGENERATION /BREAKER)
50 53 56 69 36 73 64 78 4 29 63 28 72 79 43 78 64 73 36 69 56 53 43 14 Spool-bucket 55 Socket bolt
H
G G 15 Spool-option C (dozer) 56 Washer
I 23
16 Main relief valve 57 Spring washer
792843 72
62 31 1 17 Overload relief valve 58 O-ring
50 53 56 69 18 13 67 32 32 67 19 69 56 53 51 61 30
7- 55 57 18 Overload relief valve 59 O-ring
19 Overload relief valve 60 O-ring
20 Negacon relief valve 61 O-ring
A A
21 Swing logic valve 62 O-ring
22 Bucket logic valve 63 O-ring
B B
23 Option on-off valve 64 O-ring
C C 24 Holding valve kit A1 65 O-ring
50 53 56 69 4 72 28 45 58 33 8149 48 17 17 56 53 51 25 Holding valve kit A2 66 O-ring
B-B (TRAVEL RIGHT & LEFT) D D 26 Holding valve kit B 67 O-ring
37 68 78 64 67 32 43 79 28 72 29 63 32 67 37 68 78 64 27 Regeneration block 68 O-ring
E E 28 Plug 69 O-ring
29 Plug 70 O-ring
F F 30 Plug 71 O-ring
50 53 56 6917 43 79 72 28 14 17 69 56 53 51 31 Plug 72 O-ring
22 G G 32 Plug 73 O-ring
I
33 Plug 74 Backup-ring
H 34 Plug-parallel 75 Backup-ring
F-F (OPTION-B & BUCKET) 2 54 57
50 53 56 69 69 56 53 51 35 Plug-relief cat 76 Backup-ring
36 Plug-relief cat 77 Backup-ring
21
20 15 20
37 Plug-relief cat 78 Backup-ring
29 63 40 63 75 59
50 53 56 69 6 69 56 53 51 38 Plug-bucket 79 Load check spring
G-G (OPTION-C & NEGATIVE CONTROL)
39 Plug-bucket parallel 80 Load check spring
52 17 53 56 69 8 60 77 34 65 34 65 60 77 32 67 9 69 17 40 Plug-option 81 Poppet signal spring
41 Plug-orifice 82 Pin
42 Plug
38 63 76 61 75 59 39 61 76 63
2-20
2. HYDRAULIC CIRCUIT
Pi1 Pi2
(Pump) (Pump)
PS PS
Rs Pn2 Pn1
C6
D6
Pc6
OPTION-C
(DOZER)
Pd6
B5
Puo
A5
C5
D5
Pb5
Pc5
OPTION-B Pa5
P2 (Double BUCKET
acting solenoid)
Pd5
DR5
P05 P04(Boom up pilot)
Pb3 C4
D4
Pc42 B4
DR3
Pi1(Arm safety) Pc41 OPTION-A & ARM
Pc40 Pb4
Pa4 REGENERATION CUT
Pd40
Pd41(Shuttle)
Pc42
ARM 1 V3
Pb3
Pc3
DR2
BOOM 2 & Pa21 ARM 2
SWING P05
PRIORITY Pd41
C2
D2 B2
Pc2 Pd40
A2 Pi1(Boom safety)
SWING Pd2 Pb21
DR1
Pb20
DR4
Pa20
Pa21 BOOM 1
P02 P04
(Boom priority)P03 Patt
PS
B1
C1 A1 Swing motor(SH)
D1 Pb1
Pc1
DR0
STRAIGHT P0
TRAVEL
BLOCK PS T1
P02 Ai
Pd0 P3 P2 P1 Pu
A1 A2
1409S2MC05
2-21
3. FUNCTION
1) CONTROL IN NEUTRAL
(1) P1 SIDE
The hydraulic fluid from pump A2 flows into the main control valve through the inlet port "P1",
pass the straight travel spool into the P1 bypass passage and P1parallel passage.
The hydraulic fluid from the pump A2 is directed to the tank through the bypass passage of
spools : travel left, boom 1, arm 2, arm regeneration & option A and bucket, the negative relief
valve of P1, tank passage, and the tank port "T1"
P1 port Tank port T1
B B
SECTION A-A
P1 Bypass passage
A A
TRAVEL(LH)
BOOM 1
ARM 2
ARM REGEN
& OPTION-A
BUCKET
Tank passage
2-22
(2) P2 SIDE
The hydraulic fluid from pump A1 flows into the main control valve through the inlet port "P2", into
the P2 bypass passage and P2 parallel passage.
The hydraulic fluid from the pump A1 is directed to the tank through the bypass passage of
spools : travel right, swing, boom 2 & swing priority, arm 1, option "B" and option "C" (dozer), the
negative relief valve of P2, tank passage and the tank port "T1".
B B
SECTION A-A
P2 Bypass passage
A A
TRAVEL(RH)
SWING
BOOM 2 &
SW PRIORITY
ARM 1
OPTION-B
OPTION-C
(DOZER)
Tank passage
SECTION B-B
14092MC12
2-23
2) TRAVEL OPERATION
(1) TRAVEL FORWARD OPERATION
P1 Bypass passage
C1 D1
From RCV
Pc1
TRAVEL RIGHT
Pb1
TRAVEL LEFT
From RCV
Tank passage
A1 B1
P2 Bypass passage
14092MC18
P1 Bypass passage
C1 D1
From RCV
TRAVEL RIGHT
Pd1
Pa1
TRAVEL LEFT
From RCV
Tank passage
A1 B1
P2 Bypass passage
14092MC17
During the travel forward operation, the hydraulic fluid of the pump A2 is supplied to the travel left
motor and the hydraulic fluid of the pump A1 is supplied to the other travel right motor.
The pilot pressure from the pilot control valve is supplied to the spring side of pilot port (pb1, pc1).
And it shifts travel right and left spools in the left direction against springs. Hydraulic fluid from the
pump A1 flow into the travel right spool through the bypass passage and hydraulic fluid from the
pump A2 flow into the travel left spool through the bypass passage.
Then they are directed to the each travel motor through port A1 and C1. As a result, the travel
motors turn and hydraulic fluid returns to the tank passage through the travel spools.
In case of the reverse operation, the operation is similar.
2-24
(3) TRAVEL STRAIGHT FUNCTION
Check valve
Tank port T1
Straight travel
spool
P2 port
P1 Bypass passage P1 Parallel passage
14092MC19
This function keeps straight travel in case of simultaneous operation of other actuators (boom, arm,
bucket, swing) during a straight travel.
① During travel only :
The hydraulic fluid of the pump A1 is supplied to the travel right motor and the pump A2 is
supplied to the travel left motor.
Thus, the machine keep travel straight.
② The other actuator operation during straight travel operation :
When the other actuator spool (s) is selected under straight travel operation, the straight travel
spool is moved.
The hydraulic fluid from pump A2 is supplied actuator through P2 and P1 parallel pass and travel
motors through orifice at side of straight travel spool.
The hydraulic oil fluid from pump A1 is supplied to travel motors (left/right).
Therefore, the other actuator operation with straight travel operation, hydraulic oil fluid from pump
A2 is mainly supplied to actuator, and the hydraulic oil fluid form pump A1 is mainly supplied to
travel motors (left/right).
Then the machine keeps straight travel.
2-25
3) BOOM OPERATION
(1) BOOM UP OPERATION
During boom up operation, the pilot secondary pressure from RCV is supplied to the port Pa20 of
the spring side and shifts the boom 1 spool in the left direction. The bypass passage is shut off by
the movement of the boom 1 spool and the hydraulic oil fluid from pump A2 is entered P1 parallel
passage and then passes through the load check, bridge passage and boom holding valve then
flows into the port A2. Following this it flows into the head side of the boom cylinder. (In this case,
the boom holding valve is free flow condition)
At the same time, the pilot pressure from RCV is supplied to the port Pa21 of the spring side of
boom 2 and shifts the boom 2 spool. The bypass passage is shut off by the movement of the
boom 2 spool and the hydraulic oil fluid from pump A1 entered boom summation passage via the
P2 parallel passage, the land of the swing priority spool, notch of the boom 2 spool, arm 2 spool
and the check. The flows combine in passage and are directed to port A2 and head side of boom
cylinder.
At the same time, the flow from rod side of the boom cylinder return to the boom 1 spool through
the port B2. Thereafter it is directed to the hydraulic oil tank through the tank passage.
P1 Bypass passage
Tank passage
Swing spool
Boom 1 spool
Holding valve
From RCV
Pa20
B2 A2
Boom summation P1 Parallel passage
passage
Pa21
Arm 2 spool
Boom
Boomsummation passage
summation passage Load check
14W92MC24
2-26
(2) BOOM DOWN OPERATION
During the boom lowing operation, the pilot pressure from RCV is supplied to the port Pb20 of the
spring opposite side and shifts the boom 1 spool in the right direction.
The bypass passage is shut off by the movement of the boom 1 spool and the hydraulic fluid from
the pump A2 enters the parallel passage and is directed to the port B2 through the load check.
Following this, it flows into the rod side of the boom cylinder.
At the same time, the return flow from the head side of the boom cylinder returns to the port A2
and boom holding valve. And it is directed to the hydraulic oil tank through opened tank passage
by movement of the boom 1 spool.
Meanwhile some of return flow is directed to P1 parallel passage through the internal passage of
the boom 1 spool. (boom regeneration)
In this case, the holding valve is open condition, for details of the boom holding valve, see page
following page.
During the boom lowering operation, the fluid from A1 pump is not summation.
P1 Bypass passage
Tank passage
Boom 1 spool
Pb20
B2 A2
Load check P1 Parallel passage
14W92MC26
2-27
4) HOLDING VALVE OPERATION
(1) HOLDING OPERATION
At neutral condition, the pilot piston chamber is connected to drain port through the pilot port.
And the piston "B" is supported with spring "B".
Also, the pressured fluid from actuator entered to inside of the holding valve through the
periphery hole of check, crevice of the check and the plug and the periphery hole of plug.
Then, this pressured oil pushed the poppet to the poppet seat and the check to the seat of body.
So the hydraulic fluid from actuator is not escaped and the actuator is not moved.
PLUG
CHECK
PILOT PORT
ACTUATOR PORT POPPET SEAT DRAIN PORT FOR RELEASE
HOLDING VALVE
14W92MC15
2-28
(2) RELEASE HOLDING OPERATION
The pilot pressure is supplied to the pilot port for release holding valve and shifts the piston "B" in
the left direction against the spring "B", and shifts the poppet in the left direction through piston
"B" and piston "A" against spring "B" and shifts the spool in the left side.
At same time, the return fluid from actuator returns to the drain port through the periphery hole of
check, crevice of the check and the plug, the periphery hole of the plug, in side of holding valve,
crevice of the poppet and the poppet seat, the periphery hole of the poppet seat, crevice of
socket and spool and internal passage of spool.
When the poppet is opened, pressure of inside of holding valve is decreased and the return fluid
from actuator returns to the tank passage through the notch of spool.
PLUG
CHECK
PILOT PORT
ACTUATOR PORT POPPET SEAT DRAIN PORT FOR RELEASE
HOLDING VALVE
14W92MC16
2-29
5) BUCKET OPERATION
(1) BUCKET IN OPERATION
During the bucket in operation, the pilot secondary pressure from RCV is supplied to port Pa5 of
the spring side and shifts the bucket spool in the left direction.
The bypass passage is shut off by the movement of the bucket spool and the hydraulic fluid from
pump A2 entered P1 parallel passage and is directed to the port A5 through the check 1 of
bucket logic valve.
At the same time, the hydraulic fluid from P1 bypass passage is directed to the port A5 through
the check 2.
Following this it flows into the head side of the bucket cylinder.
The return flow from the rod side of the bucket cylinder returns to the bucket spool through the
port B5. Thereafter it is directed to the hydraulic oil tank through the tank passage.
Bucket spool
From RCV
Pa5
B5 A5
P1 Parallel passage
Check 2
Check 1
Bucket logic valve
14W92MC34
2-30
(2) BUCKET OUT OPERATION
During the bucket out operation, the pilot secondary pressure from RCV is supplied to port Pb5
of the spring opposite side and shifts the bucket spool in the right direction.
The bypass passage is shut off by the movement of the bucket spool and the hydraulic fluid from
pump A2 entered P1 parallel passage and is directed to the port B5 through the check 1 of
bucket logic valve.
At the same time, the hydraulic fluid from P1 bypass passage is directed to the port B5 through
the check 2.
The return flow from the head side of the bucket cylinder returns to the hydraulic oil tank through
the port A5 and the tank passage.
Bucket spool
From RCV
Pb5
B5 A5
P1 Parallel passage
Check 2
Check 1
Bucket logic valve
14W92MC35
2-31
(3) BUCKET IN OPERATION WITH BOOM OPERATION
When combined operation, mostly same as previous page but the fluid from P1 bypass passage
is empty.
So only the fluid from P1 parallel passage is supplied to the bucket cylinder. Also, parallel
passage is installed the orifice of bucket logic valve for supplying the fluid from pump A2 to the
boom operation prior to the bucket operation. In case of the bucket out operation with boom
Bucket spool
From RCV
Pa5
B5 A5
Orifice
14W92MC29
2-32
6) SWING OPERATION
(1) SWING LEFT & RIGHT OPERATION
During the swing left operation, the pilot secondary pressure from the RCV is supplied to the port
Pd2 of the spring side and shift the swing spool in left direction. The bypass passage is shut off by
the movement of the swing spool and the hydraulic fluid from pump A1 flows into swing spool
through the P2 parallel passage. Then it is directed to swing motor through the port D2.
As the result, swing motor turns and flow from the swing motor returns to the hydraulic oil tank
through the port C2, swing spool and the tank passage.
In case of swing right operation, the operation is similar to swing left operation but the pilot
secondary pressure from the RCV is supplied to the port Pc2 of the spring opposite side.
Accordingly, the hydraulic fluid from pump A1 flows into swing motor through the port C2 and
returns to the hydraulic oil tank through the port D2 and the tank passage.
From RCV
Pd2
P2
P2Parallel
Parallelpassage
passage P2
P2 Bypass
Bypasspassage
passage
14W92MC32
2-33
(2) SWING LEFT OPERATION WITH ARM OR BOOM OPERATION
When combined operation, mostly same as previous page but the fluid from P2 bypass passage
is empty.
So only the fluid from parallel passage is supplied to the swing motor. Also, parallel passage is
installed the orifice of swing logic valve for supplying the fluid from pump A1 to the boom or the
arm operation prior to the swing operation. In case of the swing right operation with arm or boom
P03
Pd2
P2
P2Parallel
Parallelpassage
passage P2
P2 Bypass
Bypasspassage
passage
14W92MC20
2-34
7) ARM OPERATION
(1) ARM IN OPERATION
During arm in operation, the pilot secondary pressure from the RCV is supplied to the port Pc40
of spring opposite side and shifts arm 1 spool in the right direction.
The bypass passage is shut off by the movement of the arm 1 spool and the hydraulic oil from the
pump A1 flows into the arm cylinder head side through P2 parallel passage, the load check valve,
bridge passage and the port C4.
At same time, the pilot secondary pressure from the RCV is supplied to the port Pb3 of spring
opposite side and shifts arm 2 spool in the right direction. The bypass passage is shut off by the
movement of the arm 2 spool and the hydraulic fluid from the pump A2 flows into the arm
summation passage through P1 parallel passage, the check valve, the arm 2 spool and the boom
2 spool. Then it entered the arm cylinder head side with hydraulic fluid from arm 1 spool.
Pc40
Arm regeneration
cut pilot pressure
Pb4
Pc42
Arm 2 spool
Arm in pilot
pressure
Pb3
From RCV
P1Bypass
P1 Bypass passage
passage P1P1 Parallel
Parallel passage
passage 14W92MC21
2-35
ARM REGENERATION
The return flow from the arm cylinder rod side is pressurized by self weight of arm and so, returns to
port D4. The pressurized oil returning to port D4 enters the arm regeneration & breaker spool through
the arm holding valve and the arm 1 spool. It is supplied the arm cylinder head through internal
passage. This is called the arm regeneration function.
The amount of regeneration fluid is changed by movement of the arm regeneration spool. A few
fluids after P2 parallel passage is push piston "C" through the notch of arm regeneration spool and
selector spool. At this time, the selector spool is opened by pilot pressure from RCV.
Then, the arm regeneration spool shifts to right side and flow to tank pass increases and regeneration
flow decreases. Therefore, pressure of arm cylinder head increases, then, arm regeneration flow
decreases.
Furthermore, the arm regeneration cut pressure is supplied to the port Pb4 of spring opposite side
and arm regeneration spool is move into the right direction fully. The flow from the arm cylinder rod is
returned to the hydraulic oil tank and regeneration function is not activated. (The return fluid is
maximum condition)
Pc40
Arm regeneration
cut pilot pressure Arm holding valve
Pb4
Pc42
Tank passage
Arm in
pilot pressure
Arm
Armregeneration
regeneration P2 Bypass passage
&&breaker
breaker spool
spool
14W92MC22
2-36
(2) ARM OUT OPERATION
During arm out operation, the pilot secondary pressure from RCV is supplied to the port Pd40 of
spring side and shifts arm 1 spool in the left direction.
The bypass passage is shut off by the movement of the arm 1 spool and the hydraulic fluid from
pump A1 flows into arm 1 spool through the P2 parallel passage. Then it enters into the arm
cylinder rod side through the load check, bridge passage, arm holding valve and the port D4.
Also, the pilot secondary pressure from RCV is supplied to the port Pd41 of spring side and shifts
arm 2 spool in the left direction.
The bypass passage is shut off by the movement of the arm 2 spool and some of the hydraulic
fluid from pump A2 bypassed through bypass notch. The rest of hydraulic fluid from pump A2
flows into the arm summation passage through P1 parallel passage, the check valve, arm 2 spool
and boom 2 spool.
Then it enters into the arm cylinder rod side with the fluid from the arm 1 spool.
The return flow from the arm cylinder head side returns to the hydraulic tank through the port C4,
the arm 1 spool and tank passage.
Arm out
pilot pressure
Pd40
From RCV
Bypass notch
Arm summation passage
Boom 2 spool
Pd41
Arm roll out
pilot pressure
P1Bypass
P1 Bypasspassage
passage Check
Check P1Parallel
P1 Parallel passage
passage 14W92MC23
2-37
8) SWING PRIORITY FUNCTION
During swing priority operation, the pilot secondary pressure is supplied to the port Pc3 of the
spring side of the swing priority spool and shift swing priority spool in the right direction.
The hydraulic fluid from P2 parallel passage flows into the parallel passage of arm 1 side through
swing priority spool and the path "A" and also flows into the boom 2 spool.
When the swing priority spool is neutral condition, the passage is same as normal condition. But
due to shifting of the swing priority spool, the fluid from pump A1 flows to swing side more then the
boom 2, arm 1, option B and dozer spools to make the swing operation most preferential.
Swing priority
pilot pressure
Pc3
Arm22spool
Arm spool
14W92MC27
2-38
9) DOZER OPERATION
(1) Dozer
ozer down operation
DOZER Pc6
Tank passage
14W92MC30
(2) Dozer
ozer up operation
Pd6
DOZER
From dozer RCV
Tank passage
14W92MC31
During the dozer down operation, the pilot pressure from the dozer control valve is supplied into
the port Pc6 of the spring side and it shifts the dozer spool in the left direction.
The hydraulic fluid from the pump A1 enters the parallel passage and is direction to the head side
of the dozer cylinder through port D6.
The return flow from the rod side of the dozer cylinder returns to the dozer spool through C6 port.
Thereafter it is directed to the hydraulic tank through tank passage.
In case of the dozer up operation, operation is similar.
2-39
10) NEGATIVE RELIEF VALVE OPERATION
When no function is being actuated on P1 side, the hydraulic fluid from the pump A2, flows into the
tank passage through the P1 bypass passage and orifice. The restriction caused by this orifice
thereby pressurizes. This pressure is transferred as the negative control signal pressure Pn1 to the
pump A2 regulator.
It controls the pump regulator so as to minimize the discharge of the pump A2.
The bypass passage is shut off when the shifting of one or more spools and the flow through
bypass passage became zero. The pressure of negative control signal becomes zero and the
discharge of the pump A2 becomes maximum.
The negative control pressure reaches to the set level, the hydraulic fluid in the passage pushes
open negative control valve and escapes into the return passage.
For the pump A1 the same negative control principle.
Bucket spool
Negative
control spring
Tank passage
2-40
11) OPERATION OF MAIN RELIEF VALVE
(1) The pressurized oil passes through the orifice (A) of the plunger is filled up in chamber A of the
inside space, and seats the plunger against the housing securely.
Housing Tank
passage
Plunger T Orifice A
14W92MC36
(2) When the pressure at (P) becomes equal to the set pressure of the spring the hydraulic oil
passes through the piston (A) pushes open the poppet and flows to tank passage (T) through the
plunger internal passage, periphery orifice A, chamber A, periphery orifice B and the hole (E).
Tank
passage
T Hole E
14W92MC37
(3) Opening the poppet causes the pressure in chamber A to fall and the plunger to open. As the
result the pressurized oil at port P runs into tank passage (T).
Plunger Poppet
Tank
passage
T
14W92MC38
2-41
(4) The pressure at port P becomes lower than set pressure of the spring, the poppet is seated by
spring force. Then the pressure at port P becomes equal to set pressure of the spring and the
plunger is seated to the socket.
Housing Tank
passage
Plunger T
14W92MC39
(5) When the power boost switch is ON, the pilot pressure enters through hole A.
It pushes the piston (B) in the left direction to increase the force of the spring and change the
relief set pressure to the high pressure.
Housing Tank
passage
T
14W92MC40
2-42
12) OPERATION OF OVERLOAD RELIEF VALVE
FUNCTION AS RELIEF VALVE
(1) The pressurized oil passes through the piston A and orifice A is filled up in chamber A of the
inside space and seat the plunger against the socket and the socket against the housing securely.
Housing
Tank
passage Plunger Orifice A
T
14W92MC41
(2) When the pressure at port P becomes equal to the set pressure of the spring, the pressurized oil
pushes open the poppet and flows to tank passage (T) through the plunger internal passage,
orifice A, chamber A, periphery orifice B and hole E.
Housing
Peripheryorifi
Periphery orifice
ce B B
14W92MC42
2-43
(3) Opening of the poppet causes the pressure in chamber A to fall and the plunger to open. As the
result the pressurized oil at port P runs into tank passage (T).
Housing
Tank
passage Plunger
T
14W92MC43
(4) The pressure at port P becomes lower than set pressure of the spring, the poppet is seated by
spring force. Then the pressure at port P becomes equal to set pressure of the spring and the
plunger is seated to the socket.
Housing
Tank
passage Plunger
T
14W92MC44
2-44
MAKE-UP FUNCTION
(5) When negative pressure exists at port P, the oil is supplied through tank passage (T). When the
pressure at tank passage (T) becomes higher than that of at port P, the socket moves in the right
direction. Then, sufficient oil passes around the socket from tank passage (T) to port P and fills up
the space.
Housing
Tank
passage
T
14W92MC45
2-45
GROUP 3 SWING DEVICE
1. STRUCTURE
Swing device consists swing motor, swing reduction gear.
Swing motor include mechanical parking valve, relief valve, make up valve and time delay valve.
R/G grease fill port(PT 1/4) Time delay valve Relief valve Oil level gauge &
R/G Oil drain port(PT 1/2) Oil supply port
SH
SH Au
PG
PG Mu
GA GB
Dr
SH
14W92SM01
PG
B Mu A
Hydraulic circuit
2-46
1) SWING MOTOR
38
DETAIL K
6 5 11 10 9 16 19 22 7 35 34 36 37 30 32,33
27
26
25
28
29
41
44
43
42
2 3 4 1 8 13 12 15 14 17 18 23 21 20 39,40 24 31 14W92SM02
2-47
2) REDUCTION GEAR
2 4 3 23 5 1 26 7 25 6 19 8 16 10 11 9 21 12 24
20
A
16
14
18
15
17
13
22
26
25
Oil drain
Grease port
26
VIEW A
14W92SM03
2-48
2. PRINCIPLE OF DRIVING
1) GENERATING THE TURNING FORCE
The high hydraulic supplied from a hydraulic pump flows into a cylinder (9) through valve cover of
motor (20), and valve plate (23).
The high hydraulic is built as flowing on one side of Y-Y line connected by the upper and lower sides
of piston (13).
The high hydraulic can generate the force, F1=P×A (P : supplied pressure, A : water pressure
area), like following pictures, working on a piston.
This force, F1, is divided as N1 thrust partial pressure and W1 radial partial pressure, in case of the
plate of a tilt angle, α.
W1 generates torque, T=W1+R1, for Y-Y line connected by the upper and lower sides of the piston
as following pictures.
The sum of torque (ΣW1×R1), generated from each piston (4~5 pieces) on the side of a high
hydraulic, generates the turning force.
This torque transfers the turning force to a cylinder (9) through a piston; because a cylinder is
combined with a turning axis and spline, a turning axis rotates and a turning force is sent.
W1 PISTON
CYLINDER
W1
R1
N1
O A
f1 F1 P
HIGH Y LOW
14072NEWSM03
2-49
2) MAKE UP VALVE
In the system using this type of motor, there is no counter balance functioning valve and there
happens the case of revolution exceeding hydraulic supply of motor. To prevent the cavitation
caused by insufficient oil flow there is a make up valve to fill up the oil insufficiency.
A make up valve is provided immediately before the port leading to the hydraulic oil tank to secure
feed pressure required when the hydraulic motor makes a pumping action. The boost pressure
acts on the hydraulic motor's feed port via the make up valve.
Pressurized oil into the port B, the motor rotate counterclockwise.
If the plunger of MCV moves neutral position, the oil in the motor is drain via left relief valve, the
drain oil run into motor via right make up valve, which prevent the cavitation of motor.
Relief valve
A B
21092SM04
2-50
3) RELIEF VALVE
11 1 Body
2 Seat
10
5 3 Plunger
4 Spring
6 5 Adjusting screw
7
6 Piston
7 Bushing
8
8 Spring seat
9
9 Shim
12
10 O-ring
1 11 Back up ring
3 12 O-ring
4
2
14007A2SM05
3
P1
T
1
2-48(2)
2-51
① Ports (P,R) at tank pressure.
A2 m h n g
A1
P
14007A2SM06
② When hydraulic oil pressure (P×A1) reaches the preset force (FSP) of spring (4), the plunger (3)
moves to the right as shown.
P1×A1=Fsp+Pg×A2
Fsp+Pg×A2
P1=
A1
4 g
P=P1
14007A2SM07
2-52
③ The oil flow chamber g via orifice m and n. When the pressure of chamber g reaches the preset
force (FSP) of spring (4), the piston (6) moves left and stop the piston (6) hits the bottom of bushing
(7).
4 m n g
P=P2
7 6
14007A2SM08
④ When piston (6) hits the bottom of bushing (7), it stops moving to the left any further. As the result,
the pressure in chamber (g) equals (Ps).
Ps×A1=Fsp+Ps×A2
Fsp
Ps=
A1-A2
P=Ps
7 6 g
14007A2SM09
2-53
4) ANTI-INVERSION VALVE
In the event of swing motor operates switch part to drive and stop the swing part. By the action of
pump on motor, there is brake on both-side of port because of the block on both sides.
Swing part is stopped by pressure of brake (in order words, 4-5 times of inversion)
Under the operating condition, the side of anti-inversion blocks off both ports but bypassing
compressed oil which is blocked in processing of anti-inversion fixed time and amount to inverse
port, prevent increasing pressure of motor and decrease inversing action.
14W92SM10
2-54
5) BRAKE SYSTEM
(1) Control valve swing brake system
This is the brake system to stop the swing motion of the excavator during operation.
In this system, the hydraulic circuit is throttled by the swing control valve, and the resistance
created by this throttling works as a brake force to slow down the swing motion.
A B A B A B
① Brake assembly
Circumferential rotation of separate plate
(15) is constrained by the groove located
at housing (1). When housing is pressed
19
down by brake spring (19) through friction
plate (14), separate plate (15) and brake 9
piston (16), friction force occurs there. 16
15
Cylinder block (9) is constrained by this
14
friction force and brake acts, while brake
releases when hydraulic force exceeds 1
Groove
spring force.
14W92SM15
2-55
② Operating principle
a. When one of the RCV lever (1) is set to the operation position, the each spool is shifted to left or
right and the pilot oil flow is blocked. Then the pilot oil go to SH of the time delay valve (3).
This pressure moves spool (5) to the leftward against the force of the spring(8), so pilot pump
charged oil (P3) goes to the chamber G through port PG.
This pressure is applied to move the piston (16) to the upward against the force of the spring
(19). Thus, it releases the brake force.
19 5
16 G SH
PG
1 RCV lever
2 Main control valve
P3
3 Time delay valve
5 Spool 2
8 Spring
16 Brake piston
19 Brake spring
14W92SM16
2-56
b. When all of the RCV lever (1) are set the neutral position, the spool (5) returns to right.
Then, the piston (16) is moved lower by spring force and the return oil from the chamber G flows
back to tank port.
At this time, the brake works.
19 5
16 G SH
PG
1 RCV lever
2 Main control valve
3 Time delay valve P3
5 Spool
2
8 Spring
16 Brake piston
19 Brake spring
14W92SM17
2-57
GROUP 4 TRAVEL DEVICE
1. CONSTRUCTION
Travel device consists travel motor and gear box.
Travel motor includes brake valve, parking brake and high/low speed changeover mechanism.
a2
a3
R/G Oil check port(PF 3/8) R/G Oil inlet port(PF 3/8)
VIEW Y
14092TM01A
RED
T1 T2
a3 a2
Port Port name Port size
Ps P1 Main port PF 3/4
P2 Main port PF 3/4
a2, a3 Gauge port PF 1/4
T1, T2 Drain port PF 1/2
Ps Parking brake release port PF 1/4
P2 P1
Hydraulic circuit
2-58
1) BASIC STRUCTURE
Reduction gear
Travel motor
Brake valve
Parking brake
High/low speed
changeover
mechanism
Main pump
14092TM02
2-59
2) STRUCTURE
12
13
110
22 123
33 122
20 115
19 150 68
18 114
89,90 121 54
9 127
74
50
117
2 52
116
41
120
63 SECTION A - A
119
46 118
66
128
65
131
69
124
45
14
209 210 46 205 208 207 46 204 203 202 91 1 4 71 126 10 11 5 102 101 129 130 105 106 125 62 103 61 108 60 32 113 14092TM03
1 Rear flange 19 Valve 39 O-ring 65 2 Speed spool 108 Planetary gear 125 Angular bearing
2 Shaft 20 Spring 41 Parallel pin 66 2 Speed spring 109 Thrust washer 126 O-ring
3 Swash plate 21 Plug 42 Parallel pin 67 Pivot 110 Screw 127 Thrust washer
4 Cylinder block 22 Ring 43 Socket bolt 68 Steel ball 111 Needle bearing 128 Plug
5 Piston 23 Main spool 45 Snap ring 69 Set screw 112 Collar 129 Seal ring
6 Shoe 24 Main plug 46 O-ring 71 Orifice 113 Thrust plate 130 O-ring
7 Retainer plate 25 Retainer spring 47 Back up-ring 74 O-ring 114 Sun gear 131 O-ring
8 Thrust ball 26 Check plug 48 Back up-ring 75 O-ring 115 Snap ring 150 Thrust plate
9 Timing plate 27 Check valve 49 Roller bearing 89 Name plate 116 Holder 205 Body
10 Washer 28 Main spring 50 Ball bearing 90 Set screw 117 Planetary gear 206 Shim
11 Washer-collar 30 Check spring 51 Roller 91 Plug 118 Needle bearing 207 Piston
12 Piston-parking 32 Oil seal 52 Plug 101 Spindle 119 Inner race 208 Rod
13 Spring 33 O-ring 54 Plug 102 Floating seal 120 Spring pin 209 Plug
14 Spring 35 O-ring 60 Spring 103 Nut ring 121 Drive gear 210 Back up-ring
15 Friction plate 36 O-ring 61 Piston 104 Plug 122 Thrust plate
16 Mating plate 37 O-ring 62 Shoe 105 Hub 123 Cover
18 Seat valve 38 O-ring 63 Plug 106 Snap ring 124 Socket bolt
2-60
2. HYDRAULIC MOTOR ASSEMBLY
With brake valve, parking brake and high/low speed changeover mechanism.
1) FUNCTION
UNCTION
(1) Hydraulic motor
This hydraulic motor is a swash plate type piston motor and converts the force of pressurized oil
delivered from the pump into a rotational movement.
(2) Brake valve
This brake valve is incorporated in the hydraulic motor assembly and has the following four
functions.
① Smoothly brakes and stops the motor by controlling inertial rotation of the motor due to inertia of
the main body.
② Check valve function to prevent cavitation of the hydraulic motor.
③ Relief valve function to control the brake pressure of hydraulic motor and anti-cavitation valve
function to prevent cavitation.
④ Opens a port which releases the parking brake force upon running of the motor and closes the
upon stopping.
(3) Parking brake
The parking brake prevents overrunning or slippage upon parking or stopping the machine on a
slope with friction plate type brake mechanism, and combined with the hydraulic motor assembly
into an integral structure.
(4) High/low speed changeover mechanism
This mechanism changes over the tilt angle of swash plate between high-speed/low-torque rotation
and low-speed/high-torque rotation with the changeover valve and control piston.
2-61
2) OPERATING PRINCIPLE
(1) Hydraulic motor
1 9 4 3 2
F1
A P
F3
F2
(Y1)
F3
F3
ri
F3
F3
( Y2)
14092TM05
The pressurized oil delivered from the hydraulic pump flows to rear flange (1) of the motor, passes
through the brake valve mechanism and is introduced into cylinder block (4) via timing plate (9). This
oil constructively introduced only to one side of (Y1) - (Y2) connecting the upper and lower dead points
of stroke of piston (5). The pressurized oil fed to one side in cylinder block (4) pushes each piston (5)
(four or five) and generates a force (F kgf = P kgf/cm2 × A cm2). This force acts on swash plate (3) and is
resolves into components (F2 and F3) because swash plate (3) is fixed at an angle (α˚) with the axis
of drive shaft (2). Radial component (F3) generates respective torques ( T = F3 × ri) for (Y1) - (Y2). This
residual of torque (T = S (F3 × ri)) rotates cylinder block (4) via piston (5). Cylinder block (4) is spline
coupled with drive shaft (2). So the drive shaft (2) rotates and the torque is transmitted.
2-62
(2) Brake valve
① Brake released
When the pressurized oil supplied from
port (A), the oil opens valve (27) and flows
into port (C) at the suction side of hydrau-
lic motor to rotate motor.
At the same time, the pressurized oil 12
passes through pipe line (a) from a small D C
Ps
hole in spool (23) and flow into chamber
(b). The oil acts on the end face of spool
(23) which is put in neutral position by the 23 b
force of spring (28), thus causing spool (23) a
28
to slide to the left. When spool (23) slides,
port (D) on the passage return side of hy- 25
draulic motor, which is closed by the spool
groove during stoppage, communicates 27
with port (B) at the tank side and the return
oil from the hydraulic motor runs into the
tank. In consequence, the hydraulic motor B A
rotates. 14092TM06
2-63
② Stopping and stalling (brake applied)
2-64
(3) Parking brake
① Running
When the pressurized oil is supplied from 13 12 101 a 15 16
the valve, the spool of brake valve in the
hydraulic motor assembly actuates to open
the passage to the parking brake and the
pressurized oil is introduced into cylinder
chamber (a) which is composed of the
spindle of reduction gear assembly and
piston (12). When the hydraulic pressure
reaches 9.5 kgf/cm2 or more, it overcomes
the force of spring (13) and shifts piston
(12). With shift of piston (12), no pressing
force is applied to mating plate (16) and
friction plate (15) and movement of fric-
tion plate (15) becomes free. Whereby the
brake force to the cylinder in the hydraulic
motor assembly is released.
14092TM08
② Stopping 13 12 101 a 15 16
When the pressurized oil from the brake
valve is shut off and the pressure in cyl-
inder chamber (a) drops 9.5 kgf/cm2 or
less, piston (12) will return by the force of
spring (13). Piston (12) is pushed by this
force of spring (13), and mating plate (16)
and friction plate (15) in free condition are
pressed against the spindle of reduction
gear assembly. The friction force produced
by this pressing stops rotation of the
cylinder and gives a braking torque 19.7
kgf·m to the hydraulic motor shaft. Note
that oil control through a proper oil pas-
sage ensures smooth operation.
14092TM09
2-65
(4) High/low speed changeover mechanism
① At low speed - pilot pressure of less than 10 kgf/cm2
When no pilot pressure is supplied from (D) (at a pressure of 10 kgf/cm2 or less), valve (65) is
pressed toward the top by the force of spring (66) and (A) port or (B) port, the pressurized oil
supply port (C) is shut off, and oil in chamber (P) is released into the motor case via
valve(65). Consequently, swash plate (3) is tilted at a maximum angle (1) and the pis-
ton displacement of hydraulic motor becomes maximum, thus leading to low-speed rotation.
1
D
Pilot pressure
A B
Y side
C 66
A 3 61
65
B P
Drain
14092TM10
2
D
Pilot pressure
A B X side
C 66
A 3 61
65
B P
14092TM11
2-66
3. REDUCTION GEAR
1) The reduction gear is composed of a two-stage planetary gear mechanism shown in the following
figure.
101 108
117
114
121 121
117
116
116
2) The rotating motion of the hydraulic motor is transmitted to drive gear (121) of 1st stage, and the
drive gear rotate planetary gears (R, 117). Then planetary gears (R, 117) revolves inside fixed hub
(105). This rotation becomes the output of 1st stage and is transmitted to carrier No.1 and sun gear
(114). Similarly the revolution of planetary gears (F, 108) are transmitted to spindle (101). Then plan-
etary gears (F, 108) do not revolve, but rotate to hub (105). Therefore, the rotating case is driven by
the overall driving torque of hub (105).
This reduction ratio is expressed as shown below :
·Reduction ratio (I) = (Hub teeth / Drive gear teeth + 1) x (Hub teeth / Sun gear teeth + 1) - 1
2-67
GROUP 5 RCV LEVER
1. STRUCTURE
The casing has the oil inlet port P (primary pressure) and the oil outlet port T (tank). In addition the
secondary pressure is taken out through ports 1, 2, 3 and 4 provided at the bottom face.
19 Switches
No. LH RH
5 One touch decel Horn
6 Power boost Breaker
B
5
19
25
Single
operation Simultaneous 6
operation
DETAIL B RH SIDE
Tilted direction of
handle(RH)
1 P
T Tilted direction of
connector(LH, RH)
2 3
Tilted direction of
handle(LH)
VIEW A
A
Port LH RH Port size
2-68
CROSS SECTION
The construction of the pilot valve is shown in the attached cross section drawing. The casing has
vertical holes in which reducing valves are assembled.
The pressure reducing section is composed of the spool (4), spring (6) for setting secondary pres-
sure, return spring (10), stopper (8), spring seat (7, 13) and shim (5). The spring for setting the sec-
ondary pressure has been generally so preset that the secondary pressure is 5 to 20.5 kgf/cm2
(depending on the type). The spool is pushed against the push rod (9, 11) by the return spring.
When the push rod is pushed down by tilting the handle, the spring seat comes down simultaneously
and changes setting of the secondary pressure spring.
2-69
CROSS SECTION
23
25
26
24
22
21
9
19
20 16
17,27
18
14
11 15
8
7
28 10
6
13
5
12
4
3
1
2
Port 2,4 Port 1,3
1409S2RL02
2-70
2. FUNCTIONS
1) FUNDAMENTAL FUNCTIONS
The pilot valve is a valve that controls the spool stroke, direction, etc of a main control valve. This
function is carried out by providing the spring at one end of the main control valve spool and apply-
ing the output pressure (secondary pressure) of the pilot valve to the other end.
For this function to be carried out satisfactorily, the pilot valve is composed of the following ele-
ments.
(1) Inlet port (P) where oil is supplied from hydraulic pump.
(2) Output ports (1, 2, 3 & 4) to apply pressure supplied from inlet port to ends of control valve spools.
(3) Tank port (T) necessary to control the above output pressure.
(4) Spool to connect output port to inlet port or tank port.
(5) Mechanical means to control output pressure, including springs that work on the above spools.
2) FUNCTIONS OF MAJOR SECTIONS
The functions of the spool (4) are to receive the supply oil pressure from the hydraulic pump at its
port P, and to change over oil paths to determine whether the pressure oil of port P is led to output
ports 1, 2, 3 & 4 or the output port pressure oil to tank port T.
The spring (6) works on this spool to determine the output pressure.
The change the deflection of this spring, the push rod (9,11) is inserted and can slide in the plug
(14).
For the purpose of changing the displacement of the push rod through the swash plate (20) and
adjusting nut (21) are provided the handle (23) that can be tilted in any direction around the fulcrum
of the universal joint (19) center.
The spring (10) works on the case (1) and spring seat (7, 13) and tries to return the push rod
(9,11) to the zero-displacement position irrespective of the output pressure, securing its resetting to
the center position.
This also has the effect of a reaction spring to give appropriate control feeling to the operator.
2-71
3) OPERATION
The operation of the pilot valve will be described on the basis of the hydraulic circuit diagram
shown below and the attached operation explanation drawing.
The diagram shown below is the typical application example of the pilot valve.
5 6
3
1
3
P T
2 4
2-70
2-72
(1) Case where handle is in neutral position
10
T 6
P
4
1 3
21092RL03
The force of the spring (6) that determines the output pressure of the pilot valve is not applied to
the spool (4). Therefore, the spool is pushed up by the spring (10) to the position of port (1, 3) in
the operation explanation drawing. Then, since the output port is connected to tank port T only,
the output port pressure becomes equal to tank pressure.
2-73
(2) Case where handle is tilted
11
1 3
21092RL04
When the push rod (11) is stroked, the spool (4) moves downwards.
Then port P is connected with port (1) and the oil supplied from the pilot pump flows through port
(1) to generate the pressure.
When the pressure at port (1) increases to the value corresponding to the spring force set by tilt-
ing the handle, the hydraulic pressure force balances with the spring force. If the pressure at port
(1) increases higher than the set pressure, port P is disconnected from port (1) and port T is con-
nected with port (1). If it decreases lower than the set pressure, port P is connected with port (1)
and port T is disconnected from port 1.
In this manner the secondary pressure is kept at the constant value.
Besides, in some type, when the handle is tilted more than a certain angle, the upper end of the
spool contacts with the inside bottom of the push rod and the output pressure is left to be con-
nected with port P.
2-74
GROUP 6 RCV PEDAL
1. STRUCTURE
The casing (spacer) has the oil inlet port P (primary pressure), and the oil outlet port T (tank). In
addition the secondary pressure is taken out through ports 1,2, 3 and 4 provided at the bottom face.
12.4 12.4
2 1
4 3
Hydraulic circuit
21092RP01
2-75
CROSS SECTION
The construction of the RCV pedal is shown in the below drawing. The casing has vertical holes in
which reducing valves are assembled.
The pressure reducing section is composed of the spool (8), spring (6) for setting secondary
pressure, return spring (10), stopper (9), and spring seat (7). The spring for setting the secondary
pressure has been generally so preset that the secondary pressure is 5 to 19 kgf/cm2 (depending on
the type). The spool is pushed against the push rod (14) by the return spring.
When the push rod is pushed down by tilting pedal, the spring seat comes down simultaneously and
changes setting of the secondary pressure spring.
27 31 30 29 28 33 36 3
32
24
23 25,26
22
16
21 14
38 17
15 18
13
19
12 20
11
9
5 6
35
4 7
10
3
8
37 1 34 2
21092RP02
2-76
2. FUNCTION
1) FUNDAMENTAL FUNCTIONS
The pilot valve is a valve controls the spool stroke, direction, etc of a main control valve. This
function is carried out by providing the spring at one end of the main control valve spool and
applying the output pressure (secondary pressure) of the pilot valve to the other end.
For this function to be carried out satisfactorily, the pilot valve is composed of the following
elements.
(1) Inlet port (P) where oil is supplied from hydraulic pump.
(2) Output port (1, 2, 3 & 4) to apply pressure supplied from inlet port to ends of control valve spools.
(3) Tank port (T) necessary to control the above output pressure.
(4) Spool to connect output port to inlet port tank port.
(5) Mechanical means to control output pressure, including springs that work on the above spools.
2) FUNCTIONS OF MAJOR SECTIONS
The functions of the spool (8) are to receive the supply oil pressure from the hydraulic pump at its
port P, and to change over oil paths to determine whether the pressure oil of port P is led to output
ports 1, 2, 3 & 4 or the output spool to determine the output pressure.
The spring (6) works on this spool to determine the output pressure.
The change the deflection of this spring, the push rod (14) is inserted and can slide in the plug (21).
For the purpose of changing th displacement of the push rod through the cam (27) and adjusting
nut (32) are provided the pedal that can be tilted in any direction around the fulcrum of the cam (27)
center.
The spring (10) works on the casing (1) and spring seat (7) and tries to return the push rod (14) to
the zero-displacement position irrespective of the output pressure, securing its resetting to the
center position.
This also has the effect of a reaction spring to give appropriate control feeling to the operator.
2-77
3) OPERATION
The operation of the pilot valve will be described on the basis of the hydraulic circuit diagram shown
below ant the attached operation explanation drawing.
The diagram shown below is the typical application example of the pilot valve.
36072SF01
2-78
(1) Case where pedal is in neutral position
T 8
P 10
21092RP03
The force of the spring (6) that determines the output pressure of the pilot valve is not applied to
the spool (8). Therefore, the spool is pushed up by the spring (10) to the position of port 2 in the
operation explanation drawing. Then, since the output port is connected to tank port T only, the
output port pressure becomes equal to tank pressure.
2-79
(2) Case where pedal is tilted
14
21092RP04
When the push rod (14) is stroked, the spool (8) moves downwards.
Then port P is connected with port 1, and the oil supplied from the pilot pump flows through port
1 to generate the pressure.
When the pressure at port 1 increases to the value corresponding to the spring force set by tilting
the handle, the hydraulic pressure force balances with the spring force. If the pressure at port 1
increases higher than the set pressure, port P is disconnected from port 1 and port T is
connected with port 1. If it decreases lower than the set pressure, port P is connected with port
1 and port T is disconnected from port 1.
In this manner the secondary pressure is kept at the constant value.
Besides, in some type, when the handle is tilted more than a certain angle, the upper end of the
spool contacts with inside bottom of the push rod and the output pressure is left to be connected
with port P.
2-80
SECTION 3 HYDRAULIC SYSTEM
C5 A5
1 Main pump
D5 Pc5
Pb5 2 Main control valve
B(CW) Mu A(CCW)
28 Pa5 3 Swing motor
Pd5
4 Travel motor
DR5
P05
5 RCV lever(LH)
4 P04
6 RCV lever(RH)
RED RED
C4
T1
T2 T* D4 DR3
B4 7 RCV pedal
a3 a2 Pc41
Pb4 8 Boom cylinder(LH)
Pa4
Ps Pd40
9 Boom cylinder(RH)
Pc40
Pc42 10 Arm cylinder
V3 11 Bucket cylinder
Pc3 Pb3 12 Turning joint
DR2 42 13 Check valve
Pa21
Pd41 14 Check valve
P2(BW) P1(FW) P1(FW) P2(BW) C2 27
B2
15 Hydraulic tank
D2 Pc2
Pd2 Pb21 A2 16 Oil cooler
C P D F
12 A Dr B E DR1 17 Air breather
DR4
Pa20 18 Bypass valve
Pk P02 24 Pb20
19 Strainer
P03 Patt
PS
B1
20 Drain filter
C1
Pb1 A1
21 5 cartridge valve
D1 Pc1
Pd1
22 Pressure sensor
Pa1
24 Pressure sensor
41 PS 24 55 25 Terminal block
26 34 32 T 26 A1 A2 P2 A3 A1 A2 DR0
P T P
P0 26 Last guard filter
24 PS Ai T1 28 Shuttle valve(option)
Pd0 P3 P2 P1 Pu 30 Boom safety valve(option)
(1) (2) (2) (1)
31 Arm safety valve(option)
Pd5 Pc5 Pc6 Pd6 P1 T P1 T 47
32 RCV dozer lever(option)
33 EPPR valve(option)
SWING P T
5 ARM BUCKET P T
6 BOOM 26 P T TRAVEL T B
34 Breaker pedal(option)
7 Psv P A
35 Accumulator(option)
a4
A1 PS A2
36 Accumulator(option)
a1 a2
(2) (1) (4) (3) 22 PS PS 22 1 37 Stop valve(option)
(1,a) (3,b) (2,d) (4,e) (3,f) (1,g) (2,h) (4,j)
Pa1 Pb1 Pd1 Pc1
14 13 40 Selector valve(option)
25 DR#,dr# 41 Solenoid valve(option)
a b d e f g h j 16 42 Selector valve(option)
c d1 h1
43 Breaker return filter(option)
Pd2 Pc2 Pd40 Pa5 Pb5 PS
33 1 17 26 47 Quick clamp solenoid valve(option)
Pc3
(MCV)
PS 24 Pc40 Pa20 Pb20
2 26 26 Pi2
49 Pressure switch(option)
Pb4(MCV)-Cluster type 1
15 Pi1
(MCV, Pn1)
P03(MCV)-Cluster type 2 3 (MCV, Pn2) ENG 50 Adjust boom cylinder(option)
a3
P03(MCV)-Cluster type 1
Closed-Cluster type 2
Pk
(T/Joint)
Pu
(MCV) 18 20 PS 24 51 Adjust boom safety lock valve(option)
A5 A4 A3 A2 A1 21 Dr B1 B3 A3
52 Port relief valve(option)
19 53 Dozer cylinder(option)
P4 PG(S/Motor)
P3 P0(MCV) 54 Double pressure check(opt, dozer)
P2
55 Solenoid valve(option, dozer & adjust)
P1
T(dr1) 56 Selector valve(option, dozer & adjust)
57
1409S3HC01
57 Linen filter
3-1
GROUP 2 MAIN CIRCUIT
The main hydraulic circuit consists of suction circuit, delivery circuit, return circuit and drain circuit.
The hydraulic system consists of one main pump, one control valve, one swing motor, four cylinders
and two travel motors.
The swash plate type variable displacement axial piston pump is used as the main pump and is
driven by the engine at ratio 1.0 of engine speed.
To cylinders To motors
Main pump
Suction filter
(210-7) 3-03
The pumps receive oil from the hydraulic tank through a suction filter. The discharged oil from the
pump flows into the control valve and goes out the tank ports.
The oil discharged from the main pump flows to the actuators through the main control valve.
The main control valve controls the hydraulic functions.
The return oil from the actuators flows to the hydraulic tank through the main control valve and the oil
cooler.
3-2
2. RETURN CIRCUIT
Check valve(2)
Full flow filter Oil cooler 1.5 kgf/cm 2
Check valve(1)
3.0 kgf/cm 2
Check valve
Check (3)
valve(3)
1.5 kgf/cm
1.5 kgf/cm2 2
14093CI01
All oil returned from each actuator returns to the hydraulic tank through the main control valve.
The bypass check valves are provided in the return circuit.
The setting pressure of bypass check valves are 1.5 kgf/cm2 (21 psi) and 3.0 kgf/cm2 (43 psi). Usually, oil
returns to the hydraulic tank from the left side of control valve through oil cooler.
When oil temperature is low, viscosity becomes higher and flow resistance increases when passing
through the oil cooler. When the oil pressure exceeds 3.0 kgf/cm2 (43 psi), the oil returns directly to the
hydraulic tank, resulting in the oil temperature being raised quickly at an appropriate level.
When the oil cooler is clogged, the oil returns directly to the hydraulic tank through bypass check valve (1).
The full-flow filter and bypass relief valve are provided in the hydraulic tank.
The oil returned from right and left side of control valve is combined and filtered by the full-flow filter. A
bypass relief valve is provided in the full-flow filter.
When the filter element is clogged, the bypass relief valve opens at 1.5 kgf/cm2 (21 psi) differential
pressure.
3-3
3. DRAIN CIRCUIT
Return line
Turning
joint Main
pump
dr #, DR #
Return filter
Hydraulic
Drain filter oil tank
Check valve
1.5 kgf/cm2
14093CI02
Besides internal leaks from the motors and main pump, the oil for lubrication circulates. These oil have
to be fed to the hydraulic tank passing through drain filter.
When the drain oil pressure exceed 1.5 kgf/cm2 (21 psi), the oil returns to the hydraulic tank directly.
3-4
GROUP 3 PILOT CIRCUIT
Safety lock
solenoid valve Swing parking brake
MCV
Travel speed solenoid valve
Pilot pump
Suction filter
(210-7) 3-05
The pilot circuit consists of suction circuit, delivery circuit and return circuit.
The pilot pump is provided with relief valve, receives the oil from the hydraulic tank through the
suction filter.
The discharged oil from the pilot pump flows to the remote control valve through line filter, EPPR
valve, solenoid valve assemblies, swing parking brake, main control valve and safety lock solenoid
valve.
3-5
1. SUCTION, DELIVERY AND RETURN CIRCUIT
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
SAFETY
P03 Pb4 Pk Pu SOLENOID
(MCV) (MCV) (T/Joint) (MCV) VALVE
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS
1409S3HC02
The pilot pump receive oil from the hydraulic tank. The discharged oil from the pilot pump flows to
the safety solenoid valve through the line filter. The oil is filtered by the line filter. The pilot relief
valve is provided in the pilot pump for limiting the pilot circuit pressure.
The oil filtered by line filter flows remote control valve through safety solenoid valve.
The return oil flow from remote control valve is returned to the hydraulic tank.
3-6
2. SAFETY SOLENOID VALVE (SAFETY LEVER)
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
When the lever of the safety solenoid valve is moved upward, oil flows into the remote control valve
through solenoid valve and line filter.
When the lever of the safety solenoid valve is moved downward, oil does not flows into the remote
control valve, because of the blocked port.
3-7
3. BOOM PRIORITY SYSTEM
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
Pd6 (DOZER)
TURNING
B5
JOINT Puo
C5 A5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
SWING MOTOR C4 P05 P04
D4 B4
DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
Boom speed(cluster type 1) C2
BOOM 2 ARM 2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS 1409S3HC04
When carrying out the combined operation of swing and boom up, the boom up operating speed is
lowered than normal operation.
To increase working efficiency, swing speed reducing system is used.
The pilot oil from pilot pump flow into P03 port in main control valve through boom priority EPPR
valve. P03 oil pressure moves swing reducing spool to lower position and oil flow rate to the swing
motor decreased.
Then, the boom up speed is increased. This is called the boom priority system.
The boom up speed can be adjusted by the cluster. Refer to page 3-12 of the operator's manual.
3-8
4. TRAVEL SPEED CONTROL SYSTEM
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
RED RED
T* T*
Ps
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
P2(BW) P1(FW) P1(FW) P2(BW) Pd6 (DOZER)
B5
Puo
C5 A5
TURNING D5 Pb5
JOINT Pc5
Pa5
Dr
OPT-B BUCKET
Pk Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
P03 Pb4 Pk Pu
(MCV) (MCV) (T/Joint) (MCV)
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS
1409S3HC05
When the travel speed switch is pushed, the travel speed solenoid valve is actuated and the
discharged oil from the pilot pump flows to the Ps port of pilot valve in the travel motors.
As a result, the control piston is pushed by the main oil flow, thus the displacement is minimized.
When the travel speed switch is pushed once more, the travel speed solenoid valve is return to
original position by the force of spring, the hydraulic oil of Ps port returns to the hydraulic tank.
As a result, the control piston is returned by the main oil flow, thus the displacement is maximized.
3-9
5. MAIN RELIEF PRESSURE CHANGE SYSTEM
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
Pd6 (DOZER)
TURNING
B5
JOINT Puo
C5 A5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
SWING MOTOR C4 P05 P04
D4 B4
DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
Auto power boost(cluster type 1) C2
BOOM 2 ARM 2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
P03 Pb4 Pk Pu
(MCV) (MCV) (T/Joint) (MCV)
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS 1409S3HC06
When the power switch on the left control lever is pushed ON, the power solenoid valve is actuated,
the discharged oil from the pilot pump flows into Pu port of the main relief valve of main control
valve; then the setting pressure of the main relief valve is raised from 350 kgf/cm2 to 380 kgf/cm2 for
increasing the digging power.
And even when pressed continuously, it is canceled after 8 seconds.
When the auto power function is selected to enable on the cluster, the pressure of the main relief
pressure is automatically increased to 380 kgf/cm2 as working condition by the MCU. It is operated
max 8 seconds.
3-10
6. ARM REGENERATION CUT SYSTEM (CLUSTER TYPE 1)
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
Pd6 (DOZER)
TURNING
B5
JOINT Puo
C5 A5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
SWING MOTOR C4 P05 P04
D4 B4
DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
ARM
V3 REGEN
Pb3
Pc3 ARM REGEN
DR2 VALVE Pd41
Pa21
Arm regeneration(cluster type 1) C2
BOOM 2 ARM 2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS 1409S3HC07
When the arm regeneration is selected to disable on the cluster, the arm regeneration solenoid
valve is activated. The pilot oil from pilot pump flows into Pb4 port in main control valve through
solenoid valve and the arm regeneration spool is shifted to left.
Then, the oil from arm regeneration passage returns to tank and the arm regeneration function is
deactivated.
When the arm regeneration is selected to enable on the cluster, the arm regeneration function is
activated and arm in operation speed is increased.
Refer to page 2-36 for the arm regeneration function.
3-11
7. SWING PARKING BRAKE RELEASE
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
TURNING
JOINT OPT-C
Pd6 (DOZER)
B5
Puo
C5 A5
D5 Pb5
Pc5
Pa5
SWING MOTOR SH
OPT-B BUCKET
Pd5
DR5
PG C4 P05 P04
D4 B4
DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
Dr
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
B(cw) A(ccw) BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
P03 Pb4 Pk Pu
(MCV) (MCV) (T/Joint) (MCV)
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS
1409S3HC08
When one of the RCV lever (except travel lever) is tilted, the pilot oil flows into SH port through main
control valve.
This pressure moves spool so, discharged oil from pilot pump flows into swing motor PG port.
This pressure is applied to swing motor disc, thus the brake is released.
When all of the RCV lever are set in the neutral position, oil in the swing motor disc cylinder is
drained, thus the brake is applied.
3-12
GROUP 4 SINGLE OPERATION
1. BOOM UP OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21 BOOM
BOOM 2 ARM 2 HOLDING
C2 VALVE B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
RELIEF P02
VALVE BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC10
When the right control lever is pulled back, the boom spools in the main control valve are moved to
the up position by the pilot oil pressure from the remote control valve.
The oil from the A1 and A2 pump flows into the main control valve and then goes to the large
chamber of boom cylinders. At the same time, the oil from the small chamber of boom cylinders
returns to the hydraulic oil tank through the boom spool in the main control valve. When this
happens, the boom goes up. The excessive pressure in the boom cylinder head side is prevented
by relief valve. When the boom is up and the control lever is returned to neutral position, the circuit
for the holding pressure at the head side of the boom cylinder is closed by the boom holding valve.
This prevents the hydraulic drift of boom cylinder.
3-13
2. BOOM DOWN OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
RELIEF
SWING VALVE DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC11
When the right control lever is pushed forward, the boom 1 spool in the main control valve is moved
to the down position by the pilot oil pressure from the remote control valve.
The oil from the A2 pump flows into the main control valve and then goes to the small chamber of
boom cylinders. At the same time, the oil from the large chamber of boom cylinders returns to the
hydraulic tank through the boom 1 spool in the main control valve.
When the down speed of boom is faster, the oil returned from the large chamber of boom cylinder
combines with the oil from the A2 pump, and flows into the small chamber of the cylinder.
This prevents cylinder cavitation by the negative pressure when the A2 pump flow can not match the
boom down speed. And the excessive pressure in the boom cylinder rod side is prevented by the
relief valve.
3-14
3. ARM IN OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
C5 MAKE UP
JOINT D5 VALVE
Pc5 Pb5
Pa5
OPT-B BUCKET
Pd5
DR5 RELIEF
VALVE
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC12
When the left control lever is pulled back, the arm spools in the main control valve are moved to the
arm in position by the pilot oil pressure from the remote control valve.
The oil from the A1 and A2 pump flows into the main control valve and then goes to the large
chamber of arm cylinder.
At the same time, the oil from small chamber of arm cylinder returns to the hydraulic oil tank through
the arm spool in the main control valve. When this happens, the arm rolls in.
The excessive pressure in the arm cylinder head side is prevented by relief valve.
The cavitation which will happen to the head side of the arm cylinder is also prevented by the make-
up valve in the main control valve.
3-15
4. ARM OUT OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING RELIEF A5
JOINT C5
D5 VALVE
Pc5 Pb5
Pa5
OPT-B BUCKET
Pd5
DR5 MAKE UP
VALVE
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
ARM
Pc40 HOLDING Pc42
ARM 1
VALVE
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC13
When the left control lever is pushed forward, the arm spools in the main control valve are moved to
the arm out position by the pilot oil pressure from the remote control valve.
The oil from the A1 and A2 pump flows into the main control valve and then goes to the small
chamber of arm cylinder. At the same time, the oil from the large chamber of arm cylinder returns to
the hydraulic oil tank through the arm spool in the main control valve. When this happens, the arm
rolls out. The cavitation which will happen to the rod side of the arm cylinder is also prevented by the
make-up valve in the main control valve. When the arm is roll out and the control lever is returned to
neutral position, the circuit for the holding pressure at the rod side of the arm cylinder is closed by
the arm holding valve. This prevent the hydraulic drift of arm cylinder.
3-16
5. BUCKET IN OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
RELIEF
OPT-C VALVE
Pd6 (DOZER)
MAKE UP
VALVE B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC14
When the right control lever is pulled left, the bucket spool in the main control valve is moved to the
roll in position by the pilot oil pressure from the remote control valve.
The oil from the A2 pump flows into the main control valve and then goes to the large chamber of
bucket cylinder.
At the same time, the oil from the small chamber of bucket cylinder returns to the hydraulic oil tank
through the bucket spool in the main control valve. When this happens, the bucket rolls in.
The excessive pressure in the bucket cylinder head side is prevented by relief valve.
The cavitation which will happen to the head side of the bucket cylinder is also prevented by the
make-up valve in the main control valve.
3-17
6. BUCKET OUT OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
MAKE UP
VALVE RELIEF
OPT-C VALVE
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC15
When the right control lever is pushed right, the bucket spool in the main control valve is moved to
the bucket out position by the pilot oil pressure from the remote control valve.
The oil from the A2 pump flows into the main control valve and then goes to the small chamber of
bucket cylinder.
At the same time, the oil from the large chamber of bucket cylinder returns to the hydraulic oil tank
through the bucket spool in the main control valve. When this happens, the bucket rolls out.
The cavitation which will happen to the rod side of the bucket cylinder is also prevented by the
make-up valve in the main control valve.
3-18
7. DOZER UP OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC16
When the dozer control lever is pulled back, the dozer spool in the main control valve is moved to
the dozer up position by the pilot oil pressure from the remote control valve.
The oil from the A1 pump flows into the main control valve and then goes to the small chamber of
dozer cylinder.
At the same time, the oil from the large chamber of dozer cylinders returns to the hydraulic oil tank
through the dozer spool in the main control valve. When this happens, the dozer goes up.
3-19
8. DOZER DOWN OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC17
When the dozer control lever is pushed forward, the dozer spool in the main control valve is moved
to the dozer down position by the pilot oil pressure from the remote control valve.
The oil from the A1 pump flows into the main control valve and then goes to the large chamber of
dozer cylinder.
At the same time, the oil from the small chamber of dozer cylinders returns to the hydraulic oil tank
through the dozer spool in the main control valve. When this happens, the dozer goes down.
3-20
9. SWING OPERATION
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
TURNING
JOINT OPT-C
Pd6 (DOZER)
B5
Puo
C5 A5
D5 Pb5
Pc5
Pa5
SWING MOTOR SH
OPT-B BUCKET
Pd5
DR5
PG C4 P05 P04
D4 B4
DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
Dr
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
B(cw) A(ccw) BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
P03 Pb4 Pk Pu
(MCV) (MCV) (T/Joint) (MCV)
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS
1409S3HC18
When the left control lever is pushed left or right, the swing spool in the main control valve is moved
to the left or right swing position by the pilot oil pressure from the remote control valve.
Also the swing operation preference function is operated by the pilot pressure Pc3 (refer to page
2-38).
The oil from the A1 pump flows into the main control valve and then goes to the swing motor.
At the same time, the return oil from the swing motor returns to the hydraulic oil tank through the
swing spool in the main control valve.
When this happens, the upper structure swings to the left or right.
The swing parking brake, make up valve and the motor brake valve are provided in the swing motor.
The cavitation which will happen to the swing motor is also prevented by the make up valve in the
swing motor itself.
3-21
SWING CIRCUIT OPERATION
SH BRAKE OFF
BRAKE RELEASE VALVE
PG
BRAKE ON
Au
Dr
ANTI-INVERSION VALVE
MOTOR BRAKE VALVE
MAKE UP VALVE
GA GB
B(cw) A(ccw)
MAKE UP
PORT(Mu)
3-22
8. TRAVEL FORWARD AND RE
REVERSE
VERSE O
OPERATION
PERATION
ARM BUCKET BOOM
CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
RED RED
T* T*
Ps
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
Pc6
OPT-C
P2(BW) P1(FW) P1(FW) P2(BW) Pd6 (DOZER)
B5
Puo
C5 A5
TURNING D5 Pb5
JOINT Pc5
Pa5
Dr
OPT-B BUCKET
Pk Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
RCV PEDAL P T TRAVEL DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
P03 Pb4 Pk Pu
(MCV) (MCV) (T/Joint) (MCV)
A5 A4 A3 A2 A1
PG
P4 (S/Motor)
(1) (3) (2) (4) (3) (1) (2) (4)
P3 P0(MCV)
a b d e f g h j P2 HYDRAULIC TANK
d1
c h1 T P1
Pd2 Pc2 Pd40 Pa5 Pb5 PS
Pc3 LINE FILTER
Pc40 Pa20 Pb20
PS 1409S3HC19
When the travel levers are pushed forward or reverse position, the travel spools in the main control
valve are moved to the forward or reverse travel position by the pilot oil pressure from the remote
control valve.
The oil from the each pump flows into the main control valve and then goes to the each travel motor
through the turning joint.
The return oil from both travel motors returns to the hydraulic oil tank through the turning joint and
the travel spools in the main control valve.
When this happens, the machine moves to the forward or reverse.
3-23
TRAVEL CIRCUIT OPERATION
RED RED
T* T*
Ps
dr Pk
3-24
GROUP 5 COMBINED OPERATION
1. OUTLINE
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
STRAIGHT
TRAVEL A1 A2 PILOT
HYDRAULIC TANK SPOOL PUMP PUMP PUMP
1409S3HC23
The oil from the A1 and A2 pump flows through the neutral oil passage, bypass oil passage and
confluence oil passage in the main control valve. Then the oil goes to each actuator and operates
them. Check valves and orifices are located on these oil passage in the main control valve. These
control the oil from the main pumps so as to correspond to the operation of each actuator and
smooth the combined operation.
3-25
2. COMBINED SWING AND BOOM UP OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC24
When the swing and boom up functions are operated, simultaneously the swing spool and boom
spools in the main control valve are moved to the functional position by the pilot oil pressure from the
remote control valve.
The oil from the A1 pump flows into the swing motor through swing spool and the boom cylinder
through boom 2 spool.
The oil from the A2 pump flows into the boom cylinders through the boom 1 spool in the right control
valve.
The super structure swings and the boom is operated.
Refer to page 3-8 for the boom priority system.
3-26
3. COMBINED SWING AND ARM OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC25
When the swing and arm functions are operated, simultaneously the swing spool and arm spools in
the main control valve are moved to the functional position by the pilot oil pressure from the remote
control valve.
The oil from the A1 pump flows into the swing motor through swing spool and the arm cylinder
through arm 1 spool.
The oil from the A2 pump flows into the arm cylinder through the arm 2 spool of the right control
valve.
The super structure swings and the arm is operated.
3-27
4. COMBINED SWING AND BUCKET OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
A1 A2 PILOT
HYDRAULIC TANK PUMP PUMP PUMP
1409S3HC26
When the swing and bucket functions are operated, simultaneously the swing spool and bucket
spool in the main control valve are moved to the functional position by the pilot oil pressure from the
remote control valve.
The oil from the A1 pump flows into the swing motor through the swing spool in the left control valve.
The oil from the A2 pump flows into the bucket cylinder through the bucket spool in the right control
valve.
The super structure swings and the bucket is operated.
3-28
5. COMBINED SWING AND TRAVEL OPERATION
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
STRAIGHT
TRAVEL A1 A2 PILOT
HYDRAULIC TANK SPOOL PUMP PUMP PUMP
1409S3HC27
When the swing and travel functions are operated, simultaneously the swing spool and travel spools
in the main control valve are moved to the functional position by the pilot oil pressure from the
remote control valve and straight travel spool is pushed to the right by the pilot oil pressure from the
pilot pump.
The oil from the A1 pump flows into the travel motors through the RH travel spool of the left control
valve and the LH travel spool of the right control valve via the straight travel spool.
The oil from the A2 pump flows into the swing motor through the swing spool and travel motor
through the LH travel spool via the check valve and orifice in the straight travel spool.
The upper structure swings and the machine travels straight.
3-29
6. COMBINED BOOM AND TRAVEL OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
STRAIGHT
TRAVEL A1 A2 PILOT
HYDRAULIC TANK SPOOL PUMP PUMP PUMP
1409S3HC28
When the boom and travel functions are operated, simultaneously the boom spools and travel
spools in the main control valve are moved to the functional position by the pilot oil pressure from the
remote control valve and the straight travel spool is pushed to the right by the oil pressure from pilot
pump.
The oil from the A1 pump flows into the travel motors through the RH travel spool of the left control
valve and the LH travel spool of the right control valve via the straight travel spool.
The oil from the A2 pump flows into the boom cylinders through the boom 2 spool and boom 1 spool
via the parallel and confluence oil passage in case boom up operation. Also, the oil from the A2
pump flows into the travel motors through the LH travel spool via the check valve and orifice in the
straight travel spool.
The boom is operated and the machine travels straight.
3-30
7. COMBINED ARM AND TRAVEL OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
STRAIGHT
TRAVEL A1 A2 PILOT
HYDRAULIC TANK SPOOL PUMP PUMP PUMP
1409S3HC29
When the arm and travel functions are operated, simultaneously the arm spools and travel spools in
the main control valve are moved to the functional position by the pilot oil pressure from the remote
control valve and the straight travel spool is pushed to the right by the oil pressure from pilot pump.
The oil from the A1 pump flows into the travel motors through the RH travel spool of the left control
valve and the LH travel spool of the right control valve via the straight travel spool.
The oil from the A2 pump flows into the arm cylinders through the arm 1 spool and arm 2 spool via
the parallel and confluence oil passage. Also, the oil from the A2 pump flows into the travel motors
through the LH travel spool via the check valve and orifice in the straight travel spool.
The arm is operated and the machine travels straight.
3-31
8. COMBINED BUCKET AND TRAVEL OPERATION
ARM DOZER BUCKET BOOM
CYLINDER CYLINDER CYLINDER CYLINDER
TRAVEL MOTOR
Pi1(Pump) Pi2(Pump)
Rs Pn2 Pn1
C6
D6
Pc6
OPT-C
Pd6 (DOZER)
B5
Puo
TURNING A5
JOINT C5
D5 Pb5
Pc5
Pa5
OPT-B BUCKET
Pd5
DR5
C4 P05 P04
D4 B4
SWING MOTOR DR3
Pc41
Pb4
Pa4
Pd40
Pc40 Pc42
ARM 1
V3 ARM
REGEN Pb3
Pc3
DR2 Pd41
Pa21
BOOM 2 ARM 2
C2
B2
D2 Pc2
Pd2 Pb21 A2
SWING DR1
DR4 Pb20
Pa20
P02
BOOM 1
P03 Patt
PS
B1
C1
D1 Pc1 Pb1 A1
Pd1 Pa1
TRAVEL(R) TRAVEL(L) SH
DR0 (S/Motor)
P0
PS T1
Ai
P2 P1 Pu
STRAIGHT
TRAVEL A1 A2 PILOT
HYDRAULIC TANK SPOOL PUMP PUMP PUMP
1409S3HC30
When the bucket and travel functions are operated, simultaneously the bucket spool and travel
spools in the main control valve are moved to the functional position by the pilot oil pressure from the
remote control valve, and the straight travel spool is pushed to the right by the oil pressure from pilot
pump. The oil from the A1 pump flows into the travel motors through the RH travel spool of the left
control valve and the LH travel spool of the right control valve via the straight travel spool of the
control valve.
The oil from the A2 pump flows into the bucket cylinder through the bucket spool via the confluence
oil passage. Also, the oil from the A2 pump flows into the travel motors through the LH travel spool
via the check valve and orifice in the straight travel spool.
The bucket is operated and the machine travels straight.
3-32
SECTION 4 ELECTRICAL SYSTEM
1. LOCATION 1
28 27
29 26
30 25
31 24
32
B
A
C
19
23
22
21
1
20
2
3
4
5
6
7 Electric box
8
10 18
11 15 17
14 CN-16&16A
CN-16B
13 16
12
1409S4EL01
4-1
2. LOCATION 2
4
21 1
1
1
11 1
23
BOOM BOOM SAFETY VALVE SOLENOID VALVE CAB
2 8 9 10 22
a3
14
12
a1
a2
13
3 16
5
1
15 6
20
Ai
19
7 Patt
17
hi
18
c
1409S4EL02
4-2
GROUP 2 ELECTRICAL CIRCUIT
CIRCUIT(1/2 CLUSTER TYPE 1
1)
AC COMP RY
CS-74A
R/DRYER 5R 146 5R
CS-74
146
1
87a 87 85
30 86
WASHER PUMP 145 5W 143 5R
2
Pa
POWER RY
M
MASTER SW 138 2WR
CABIN LAMP RY
CN-22
CN-29
60A
FUSE BOX
DO-5
CR-7
CN-95
87a
2
1
30
86
87a 87 85
85
2
87
CIRCUIT BREAKER
30 86
2
MASTER SW
1
5W 145
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
87a 87 85
30 86
1
2
3
4
5
6
7
8
9
2
5W 144
30A
10A
30A
30A
20A
10A
10A
10A
20A
20A
10A
10A
10A
20A
30A
30A
10A
20A
30A
30A
10A
20A
10A
20A
20A
20A
20A
20A
10A
20A
10A
1
MANUL RESET
0.8GrW
0.8GrW
CR-35
0.8V
0.8L
0.8L
0.8V
0.8
0.8
0.8V
0.8
87a
FUEL CUT-OFF RY
ROOM LAMP/CASSE
30
86
85
CR-9
87
87a
5R
30
86
85
87
CABIN LAMP(OPT)
2
BEACON(OPTION)
AIR CON/HEATER
148A
148E
5R 142 BATTERY
149
150
NO. CN-11
39E
149
13A
SWITCH PANEL
DESTINATION 1
39A
0.8WOr
60
13
FUEL HEATER
2
CS-74B
2B 129
START, STOP
FUEL HEATER RY
AC& HEATER
CONVERTER
2WR
SAFETY SOL
TRAVEL SOL
0.8B
WORK LAMP
1 AC GND 1 CN-60
SOLENOIDE
HEAD LAMP
30A
0.8Gr
FUEL PUMP
MCU CONT.
2W
START KEY
MCU_EPPR
60B
4 5
60R
3
FUEL HEATER FUEL PUMP
0.8R
CASSETTE
1
IG POWER
2
PRE-HEAT
2 BLOWER SIG.
2R
CLUSTER
CLUSTER
2
2V
2L 148
CR-51
OPTION
87a 87 85
30 86
138
3 AC 24V
SPARE
WIPER
WIPER
3
CN-36
G3
CIGAR
M
24
34
HORN
140
140A
MCU
21
30
CR-1
CN-96
4 REVERSE FAN
2W
2W
5
2
4
3
4 12V X 2
3Y 147
5 AC CONTROLLER B+ 5 G23 1.2B
CR-46
2
1
0.8 150
CN-61
87a
6 AC COMP 6 141 1.2G
39 0.8GrW
0.8RW
1.2RW
0.8RW
TO:STARTER "B" TERM.
30
1.2R
86
85
0.8Y
104 1.2ROr
87
0.8V
0.8L
0.8Gr
1.2Or
1.2Gr
1.2Or
1.2Br
1.2Br
2Br
2W
2W
2RW
0.8
0.8R
1.2R
1.2V
2.0Y
0.8V
1.2V
3Y
0.8L
1
2
7 AC CONDENSOR FAN 7
2Br
0.8
0.8
2R
2Y
2B
2L
2L
0.8ROr 10E
8 ILLUMINATION 8
BATT RY
147
24
25
78
23
00
00
00
00
12
130
140
131
124
148
134
132
126
79
86
32
26
26
17
50
87
18
16
20
47
0.8V
87A 0.8L
2B
2Y
6
5
G31
AIR CON HARNESS
2Br
133
2L
DO-3
141E 0.8G
2
133
122
0.8B 4
87
G24 0.8B
G21
126
1
CN-5
0.8Y 1
1 CLUSTER_RX 1
0.8L 2
2 CLUSTER_TX 2
SH 3G
3 SHIELD 3
0.8B 4
4 CLUSTER_GND 4
0.8Gr 5
5 CLUSTER_IG 5
0.8RW 6
6 CLUSTER_BATT.24V 6
7 ECONO SW_COM 7
8 ECONO SW_NO 8 CD-44
0.8BW 82 80H 1.2ROr
9 P_DUMP(SERVICE CONN.) 9 A SUPPLY
0.8Br 7 91 1.2LW
10 QUICK COUPLER SW_NO 10 B SIG
0.8Br 7 81H 1.2BW
11 OVERLOAD SW_COM 11 C RETURN
0.8ROr 00
12 OVERLOAD SW_NO 12 A3
0.8ROr 10A
13 ILLUMINATION 13
14 HOUR METER SIG.
0.8W 11 CD-18
14
0.8G 74
15 RS232 RX(SERVICE CONN.) 15 1 1.2GrW
0.8R 73 Pa
16 RS232 TX(SERVICE CONN.) 16
0.8B 3F
17 GND(SERVICE CONN) 17
0.8R 12 ENG OIL PS
18 WIPER CONT_BATT.24V 18
0.8V 13
19 WIPER CONT_WASHER P/P DRIVE 19
0.8V 51 CN-28
20 CAN_Hi(SERVICE CONN) 20 2 1.2VW
0.8G 52 1
21 CAN_Lo(SERVICE CONN) 21
SH 53
22 CAN SHIELD 22
0.8 00
23 CAMERA_2 23 AC COMP
0.8GrW 39 CN-2
24 WIPER IG 24 1.2GrW
1.2ROr 104 46 0.8Y 1
25 OPTION SW 25 1
1.2B 15 2 CN-79
26 HEAT SEAT_GND 26 1.2VW 2 2B
1.2Gr 16 60 0.8V 3
27 CIGAR LIGHTER_IG 27 3 G
1.2V 17 00 0.8 1.2 00 4 2W
28 DC-DC CONVERTER 24V 28 4 F
1.2Or 18 86E 0.8 1.2LW 5 5 1.2LW
29 SPARE SW_COM(IG) 29 5 H
1.2B 19A 6
30 GND 30 19 2B FUEL CUT OFF SOL
1.2B 19E 7
31 GND 31
64 2W 2W 4
32 NC 32 8 CN-75
20 56 Or 1.2Or 6 6 1.2Or
1.2Br 9 2
33 BEACON SW_COM(IG) 33 7 1.2Br
1.2V 21A 21 2V 75 Br 1.2Br 7
34 CABIN LIGHT 34 10 1
0.8BOr 22 8 Y 1.2Y 8
35 START KEY SW_START 35 11 EPPR VALVE
1.2W 23 9 L 1.2L 9
36 START KEY SW_COM 36 12
00 0.8 1.2 00 CD-17
37 CAMERA_3 37 13 8 1.2Y
68 2B 2B 3 2
m
0.8V 21E 14
rp
38 CABIN LIGHT 38 9 1.2L
00 0.8 1.2 00 1
39 REVERSE FAN AUTO 39 15
40 REVERSE FAN MANUAL 40
SPEED SENSOR
41 RS232 RX2(GPS) 41
0.8BrW 77 REAR ENGINE HARNESS
0.8GrW 76
42 RS232 TX2(GPS) 42
CR-23 CN-45
43 NC 43 CN-3
68A 0.8B 1.2 10 10 B
1
M
44 NC 44 1 M
64E 0.8 1.2 11 11 Gr
45 NC 45 2 2
0.8Y 25 66 0.8W 1.2 12
46 CASSETTE RADIO_BATT.24V 46 3
0.8V 26 67 0.8Y 1.2 13 B+
47 CASSETTE RADIO_IG 47 4 START RY FROM BATT.RY
0.8B 27 81A 0.8 1.2 14 STARTER
48 CASSETTE RADIO_GND 48 5
0.8BrW 28 43 0.8 1.2 15
49 SWITCH PANEL_HEAD LIGHT 49 6
0.8VW 29
50 SWITCH PANEL_WORK LIGHT 50 7
15 R CN-74
51 NC 51 8 RS-1
16
52 NC 52 9 2 B+
3W/300 12A
53 NC 53 10 1 G
0.8 84 1 P
54 SWITCH PANEL_PREHEAT 54 11 12 1.2W 3~
0.8Gr 30 2 L
55 SWITCH PANEL_CABIN LAMP 55 12 U
0.8RW 32 3 FI
56 SWITCH PANEL_TRAVEL ALARM 56 4 NC
0.8RW 32
57 SWITCH PANEL_IG 57
0.8B 33 CR-24 ALTERNATOR
58 SWITCH PANEL_GND 58 15R
0.8WOr 34 13 V
59 START SW_ACC 59 CN-80
0.8GW 35
60 START SW_BR 60 15R
PRE-HEAT RY Pre-heater
CN-8
1 NC 1
2 NC 2 CD-8
14 B
3 NC 3 1 C
15 G
4 NC 4 2
0.8 18
5 GND 5 WATER TEMP SENDOR
6 NC 6
0.8 18
7 ILLUMINATION 7
8 NC 8
9 NC 9
10 NC 10
CR-36
55 0.8BOr
1
11 NC 11 132A 0.8L 4 5 1
2
12 NC 12 132 0.8L
3
CN-7 4
1 NC 1 67 0.8Y 3 2
5
2 NC 2
PRE-HEAT RY
3 NC 3
0.8 18 CR-5
4 SEAT HEAT 4 131 2.0Y
0.8Or 18 30
5 BREAKER SW 5 22 0.8BOr 87a 87 85
0.8BW 40 86
6 BREAKER SW 6 64 2W
0.8B G42 87
7 HORN 7 123 0.8Br
0.8GrW 41 85
8 HORN 8 30 86
87a
9 BUTTON 2 9
10 BUTTON 2
ANTI-RESTART RY
10
11 BUTTON 1 11 CR-13
50 1.2Br
12 BUTTON 1 12 30
50A 0.8Br 87a 87 85
13 NC 13 86
0.8Gr 42 10 1.2ROr
14 ACCEL DIAL SUPPLY 14 87
0.8W 99 28 0.8BrW
15 ACCEL DIAL SIGNAL 15 85
0.8B 37 30 86
16 ACCEL DIAL GND 16 87a
CR-2
41 0.8GrW
1
124A 0.8V 4 5 1
CN-140 2
B 152 124 0.8V
1 3
0.8Br 7 G12
CN-25
2 4 0.8B
127 0.8G 3 2 2
5 127 0.8G
QUICK CLAMP 1
HORN RY
CD-10 HORN
1.2B 81S G13 0.8B
2
Pa 1.2YOr 127 0.8G
83 1
G32
47E
120
121
158
136
80
98
81
0.8ROr
0.8GW
0.8LOr
0.8BW
0.8BW
0.8Or
0.8Br
0.8Br
0.8B
2B 3
CN-15
10
11
12
2
6
7
8
9
1
4
3
5
0.8Gr 42A
37A
2B
1
2
3
4
5
36
6
7
4
5
63
54
122
118
118
118
118
118
118
118
118
123
118
118
118
118
118
118
118
0.8GrW 76
0.8GrW 76
0.8BrW 77
0.8BOr 55
0.8OrW 90
91
00
00
0.8GrW 76
99
82
66
36
00
0.8GrW 76
0.8GrW 76
8
9
78
37
1.2RW 79
3
1.2ROr 80
0.8Gr 42
54
63
11
51
51
73
52
74
80G
81G
80G
81G
3A
W
53
81
80E
81E
80A
81A
G
81H
80A
81A
80A
B
81J
1
92
92
94
0.8WOr 96
80
0.8OrW 90
91
0.8BW
8
0.8LW
0.8W
0.8W
0.8W
0.8W
1.2R
0.8G
0.8G
0.8G
0.8B
0.8Y
0.8R
0.8V
0.8V
0.8V
0.8V
0.8Y
CN-76
0.8L
0.8L
1.2B
1.2B
0.8L
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8ROr
0.8ROr
0.8ROr
0.8ROr
0.8
0.8BOr
0.8
0.8
SH
0.8ROr
0.8ROr
0.8ROr
0.8YW
0.8BW
0.8YW
0.8BW
0.8BW
0.8BW
0.8BW
0.8BW
0.8BW
6
5
4
3
2
1
0.8LW
0.8V
0.8Or 47G
CN-51
70
47A
134
SIG
CN-52
105
0.8RW 104
47H
0.8GOr 118
0.8Rw 106
0.8BrW 119
M+
P+
NC
49
M-
47
P-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
CD-31
6
7
CD-43
CD-42
CD-24
CD-32
0.8V
CD-6
CD-7
0.8ROr
1
0.8BW
0.8BW
5
1.2G
RETURN C
RETURN C
RETURN C
RETURN C
2
A
B
A
B
A
B
A
B
1.2V
RETURN C
0.8W
RETURN C
RETURN C
A
B
A
B
A
B
0.8Or
0.8Or
0.8Or
BOOM PRIORITY EPPR+
M
SPEED SENSOR+(HMC)
TRAVEL PS SENSOR(A)
BOOM PRIORITY EPPR-
0.8
0.8
PRE-HEAT SELECT SIG
TR ALARM SELECT SIG
0.8LOr
0.8GW
ATT PILOT PRESSURE
BOOM UP PS SENSOR
ARM IN_OUT BK IN PS
AIR CLEANER SW(NO)
RS485+(TX)-CLUSTER
WORK PS SENSOR(A)
SUPPLY
SUPPLY
SUPPLY
SUPPLY
0.8Or
SUPPLY
SUPPLY
0.8Or
0.8Or
PUMP POWER EPPR-
0.8Br
ATT_ CONFLUX SOL.
OVERLOAD SENSOR
0.8Br
6
GOV.POTENTIO SIG.
3
0.8B
HYD.TEMP SENDER
ONE TOUCH DECEL
SWING PS SENSOR
P1 PRESS SENSOR
P2 PRESS SENSOR
RS232C1_RX-HRDT
RS232C1_TX-HRDT
ENG PRE-HEAT RY
FUEL WARMER RY
BATT.POWER_24V
RS232C2_TX-RCM
CN-133
CN-242
POWER MAX SOL
CD-69
TACHO SENSOR+
PROGRAM DUMP
POWER_24V OUT
CN-70
CN-68
SIG
SIG
SIG
SIG
2
1
ATT_PRESS SOL.
CN-88
ARM REGEN SOL
SIG
TACHO SENSOR-
CN-135
COOLENT LEVEL
SIG
SIG
ACCEL ACTUATOR
TRAVEL BUZZER
1
ENG.OIL FILTER
1
2
1
2
RETURN C
1
A
B
2
CN-236
CN-149
G/A MOTOR(+)
CN-237
GND_RETURN
CN-66
G/A MOTOR(-)
HOUR METER
BLOWER SIG.
CN-81
CAN_SHIELD
1
2
1
2
1
2
SWING OVER BOOM
ENG OIL PS
P2 P1
SUPPLY
ATT. EPPR-
ATT.EPPR+
ALT. LEVEL
TRAVEL WORK
GND_MAIN
EPPR GND
POWER IG
CAN1 Hi
SIG
ATT BOOM ARM TRAVEL POWER SAFETY 1409S4EC01
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
FLOW PRIORITYREGEN HIGH MAX ATT. PS ATT ATT. ATT. BREAKER SOL
TRAVEL BZ PRESS SAFETY CONFLUX
MCU SOL
4-3
·ELECTRICAL
ELECTRICAL CIRCUIT(2/2
CIRCUIT CLUSTER TYPE 1)
1
Service Tool DC/DC CONVERTER CIGARLIGHT RELAY
OVERLOAD SW INTAKE M/ACT MODE(D/FOOT) MODE(VENT)
12V SOCKET HOUR METER TEMP M/ACT BLOWER
24V
12
RS232 P_DUMP
12
10
3
4
ECONO SWITCH
9
12V
1 4 2 7 1 4 2 7 BLOWER
h
12
M 3 M
RS232_RX
3 M M
3
12
7
1
7
RS232_TX
10
3
4
9
CAN2_Lo
CAN2_Hi
CN-48
GND
CAN_Lo
CAN_Hi
5 5
12V
24V
CL-2
IG 24V
M
4
2
GND
CN-138
CN-139
5
6
7
5
6
7
5
6
7
1
2
3
4
5
6
7
1
2
3
4
1
2
3
4
1
2
3
4
3
2
1
CS-67
11
1
1
2
8
C
CS-50
A
B
1
1
2
1
4
2
3
10
11
12
CN-21
9
4
8
1
2
3
6
7
11
1 12
1.2Gr
1
1.2B
2
ROr
0.8W
CS-52
0.8B
0.8Y
3 1 WIPER CUT SW 00
G
0.8G
B
E
A
F
10
11
1.2Or
12
J
R 10
9
3
24M 1.2B
1
2
3
6
7
1.2Or
1.2V
24L 1.2B
0.8VOr
2 9 0.8Br
0.8Or
0.8Or
0.8Br
Gr 12 4
24Q
0.8V
24R 0.8B
12B
5 3
35E
24V
21
13
4A
CS-53
R 5
1 0.8BW
60
0.8Or
27F 0.8Br
4
60
22
0.8G
0.8G
0.8B
24T 0.8B
6 0.8G
6 0.8G
6 0.8G
6 0.8G
2 0.8G
3 0.8R
5 0.8V
4 0.8B
4 G 8 6
61
11
27
10
61
5 23F 0.8Or 3
L 9 7 7 AIR-CON HARNESS
B
6 M 2 6 23F 0.8Or 9
62
62
Or
CN-126
8
7
2A
4 CN-11 NO. DESTINATION
10
9
8
7
6
5
4
9 8
3
2
1
11
10 1 1 GND
WIPER MOTOR 10
9A 0.8Br 2 2 BLOWER SIG
11
0.8BW
24S 0.8B 11 12 3 3 FUSE(IG)
0.8G
0.8G
0.8R
0.8V
0.8B
12
4 4 REVERSE FAN
CN-141 QUICK CLAMP SW
G 8 5 5 FUSE(Battery)
59
73
72
71
70
69
FEED BACK 1
W 1 6 6 DPS(COMPRESSOR)
MOTOR DRIVE SIG 2 CN-17 CN-113
L 9 00 0.8B 7 7 CONDENSOR FAN
MOTOR DRIVE- 3 1
R 10 1 W 0.8W 48 1 8 8 ILLUMINATION
MOTOR DRIVE+ 4 2 00 0.8G
B 2 2 B 1.2B 24B 2
GND 5 3
GrW 3 3 GrW 0.8ROr 65 BUZZER
VCC 6 4
R 4 4 R 0.8R 14
CONTINUE 24V 7 5
V 5 5 V 0.8V 15
WASHER P/P 8 6
L 6 6 L 0.8L 49
WASHER SIG. 9 7
Br 7 7 Br 0.8Br 50 CN-56
INT. SIG 10 8 6 0.8RW RW
Or 11 1 BATT.24V
WIPER CUT SW 11 WR
2 SIG_3
N.C 12 81 1.2B B
FEED BACK 13
Gr 12 WIPER MOTOR HARNESS 1 0.8Y
3
Y
GND
4 TX
5 0.8Gr Gr
WIPER MOTOR CONTROLLER 5 IG 24V
WL
6 SIG_2
10
11
12
13
14
15
16
17
18
10
11
12
13
14
1 0.8W W
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
7 CAMERA SIG
2 0.8L L
8 RX
0
DUCT SENSOR(GND)
0
0
TEMP MOTOR ACT(-)
DPS(COMPRESSOR)
MODE M/ACT(FOOT)
BLOWER RELAY(Lo)
INLET MOTOR(REC)
2
1
CLUSTER
INLET MOTOR(FRE)
MODE M/ACT(PBR)
MODE M/ACT(DEF)
AMBIENT SENSOR
TEMP M/ACT(PBR)
CONDENSOR FAN
MOTOR ACT(REF)
DUCT SENSOR(+)
W/TEMP SENSOR
MODE M/ACT(M+)
POWER TR BASE
MODE M/ACT(M-)
FET(FEED BACK)
INCAR SENSOR
REVERSE FAN
ILLUMINATION
ILLUMINATION
CS-82 CN-5
BATTERY(+)
FET(GATE)
POWER AMBIENT INCAR
POWER IG
0.8B 20E 1 0.8Y W/TEMP
12 1 1 MCU_RX TR
12 11 0.8LW 26A 2 0.8L DUCT SENSOR SENSOR SENSOR
IG 24V
11 2 2 MCU_TX
GND
3 SH SENSOR
NC
NC
NC
10 3 3 MCU_GND
10 4 0.8B
8 9 4 4 GND
4 1.2ROr 19A 5 0.8Gr AC & HEATER CONTROLLER(auto)
8 5 5 FUSE
9 6 0.8RW
7 7 6 6 FUSE
3 7 0.8B CS-1 CN-24
6 7 7 NC Gr 11
8 0.8Or 0.8G 2
5 8 8 NC 2
1.2LW 26 59 0.8BW 0.8V 3 CN-10 NO. DESTINATION
4 9 9 P_DUMP(MCU) 1
9 0.8Br CL-1 1 1 NC
3 10 10 QUICK COUPLING SOL Gr 11
10 0.8V
DOOR SW 3 SPEAKER-RH 2 2 NC
2 11 11 OVERLOAD PS 0.8Y 1 1 0.8Y
12 1 11 0.8VOr 2 3 3 FUSE
1 12 12 MCU_OVERLOAD 0.8B 6 2 0.8G
12 0.8ROr 1 4 4 CASSETTE_RH-
SPARE SW 13 13 HEAD LAMP RY 3 0.8V
13 0.8W CN-23 ROOM LAMP 5 5 CASSETTE_RH+
14 14 MCU_HOURMETER 0.8Y 4 4 0.8Y
69 0.8G 2 6 6 CASSETTE_LH-
15 15 RS232_RX(MCU) 0.8L 5 5 0.8L
70 0.8R 1 7 7 CASSETTE_LH+
16 16 RS232_TX(MCU) 6 2.0B
71 0.8B SPEAKER-LH 8 8 GND
17 17 GND 7 2.0B
14 0.8R CL-7 9 9 GND
18 18 FUSE 1.2BrW 8 8 1.2BrW
15 0.8V 10 10 BEACON SW
19 19 WASHER P/P M 1.2B 6A 9 2.0V
72 0.8V 11 11 CABIN LIGHT RY
20 20 CAN_Hi 10 2.0V
73 0.8G BEACON LAMP 12 12 CABIN LIGHT RY
21 21 CAN_Lo
74 SH
22 22 Shieeld CL-8
2.0V 9 10 2.0V
CL-9 CABIN HARNESS
23 23 NC 2 2
65 0.8ROr 1.2B 6B 7 1.2B
24 24 WIPER FUSE 1 1
19 1.2ROr
25 25 FUSE CABIN LIGHT CABIN LIGHT
20 1.2B
26 26 GND
21 1.25Gr
27 27 FUSE
CS-23
22 1.2V
CS-83 ACCEL DIAL LED
28 28 FUSE
CN-279
0.8B 24J 23 1.2Or 0.8B 19G
12 29 29 FUSE 12 CS-26A
1
2
12 11 0.8BrW 58A 24A 1.2B 12 11 0.8Or 18A 5E 0.8BW
11 30 30 GND 11 2
24E 1.2B 4E 0.8G
10 24 2B 31 31 GND 10 1
10 10 0.8G 15
0.8ROr
0.8B
8 9 32 32 NC 8 9
4 1.2Br 27E 27 1.2Br 4 0.8V 16 BREAKER SW
8 33 33 FUSE 8
9 28 2V 28A 1.2V 9 0.8BrW 17
7 34 34 CABIN LAMP RY 7 7 CN-156
19F
7
32
3 29 1.2BOr 3 19 1.2B
6 35 35 ANTI RESTART RY 6 2
30 1.2W 31 1.2ROr
5 36 36 FUSE 5 1
1.2BrW 58 0.8Or 18
4 37 37 NC 4
20
AIR SEAT
28E 0.8V 0.8Gr
3 38 38 CABIN LAMP RY 3 CN-8 NO. DESTINATION
2 39 39 NC 2 15 0.8G
12 1 12 1 1 1 NC
1 40 40 NC 1 16 0.8V
75 0.8BrW 2 2 FUSE
41 41 RS232 RX2 CREEP SW 17 0.8BrW
BEACON LAMP SW 76 0.8GrW 3 3 CRAB COM
42 42 RS232 TX2 18 0.8Or
CN-125A CS-99 4 4 NC
0.8W 30E 43 43 NC 0.8B 19A 19 1.2B
BATTERY POWER 1 12 5 5 NC
1.2R 47A 44 NC 12 11 0.8GW 21A 20 0.8Gr
KEY "IG" 2 44 11 6 6 CRAB SIG_MCU
45 45 NC 32 0.8ROr
NC 3 35 0.8Y
10 7 7 ILLUMINATION
0.8BrW 75 46 FUSE 10 22 0.8L
RX232(1)-TX 4 46 8 9 8 8 NC
0.8B 71A 36 0.8V 4 0.8L 22 23 0.8VW
RX232(1)-GND 5 47 47 FUSE 8 9 9 NC
37 0.8B 0.8L 22A 24 0.8R
48 48 GND 9
RX232(2)-RX 6 38 0.8BrW 7 7 10 10 NC
49 49 HEAD LAMP RY 3 25 0.8LW
RX232(2)-TX 7 6 11 11 NC
39 0.8VW 26 0.8RW
RX232(2)-GND 8 50 50 WORK LAMP RY 5 12 12 NC
0.8GrW 76 00 0.8B 0.8GW 21
RX232(1)-RX 9 51 51 CAMERA GND 4
00 0.8W
NC 10 00 SH
52 52 CAMERA SIG 3
0.8RW 26 RH CONSOLE HARNESS
MAIN GND 11 53 53 CAMERA SHIELD 2
0.8B 24H 40 0.8WOr 12 1
MAIN GND 12 54 54 PRE-HEAT 1
41 0.8Gr
55 55 CABIN LAMP RY
RMS 42 0.8YW AIR COMP SW
56 56 MCU_TRAVEL ALARM SW CN-7 NO. DESTINATION
CN-10 43 0.8RW CS-100
57 57 FUSE 0.8B 19E 1 1 NC
1 NC 1 44 0.8B 12
58 58 GND 12 11 0.8V 29
2 2 NC
2 NC 2 45 0.8WOr 11
0.8Y 35A 59 59 POWER RY 0.8V 29
3 ROOM LAMP 24V 3 46 0.8GW 10 3 3 NC
0.8G 51 60 60 BATT. RY 10 0.8VW 23 31 1.2ROr
4 SPEAKER RH- 4 6 9 4 4 NC
0.8V 53 4 BREAKER 0.8G 4 4 0.8G
5 SPEAKER RH+ 5 8 1 5 5 BREAKER SW
0.8Y 52 B 0.8BW 5 5 0.8BW
9 2 6 6 BREAKER RY
6 SPEAKER LH- 6 5 7 CS-26 0.8B 6
0.8L 55 3 0.8R 24 6 0.8B
7 SPEAKER LH+ 7 6 HORN 1 7 7 GND
1.2B 24F 24 2B CS-2 0.8R 24A R 0.8Grw 7 7 0.8Grw
30 1.2W 2 8 8 HORN RY
H0 I
8 GND 8 5 CS-5 0.8L 8
1.2B 24G 1 0.8Br 30 8 0.8L
9 GND 9 46 0.8GW 4 9
9 9 NC
2 L 0.8L
0, I
1.2BrW 58 2 0.8LW 25 9 0.8L
10 BEACON LAMP 10 47 1.2R 3 10 10 NC
3 4 0.8Gr 10 10 0.8Gr
H BRACC
1.2V 28F 28 2V
11 CABIN LIGHT 11 2 1 Gr
11 11 NC
1.2V 28G 4 1 12 1 0.8Br 30 0.8Gr 11 11 0.8Gr
B
2 12 12 NC
12 CABIN LIGHT 12 3 1
5
29 1.2BOr SPARE SW CN-142 13 13 NC
CABIN HARNESS 6
+ A
0.8Gr 12 12 0.8Gr
14 14 MCU_5V
STC
5 0.8W 13 13 0.8W
6 S B 15 15 MCU_ACCEL SIG.
0.8B 14 14 0.8B
START KEY SW - C 16 16 MCU_SUPPLY GND
CN-116 ACCEL DIAL
12 NC
44 0.8B
11 GND
43 0.8RW CS-33
10 POWER 24V
6 6
9 NC
42 0.8YW 5 5
8 TRAVEL ALARM
41 0.8Gr
7 CABIN LIGHT OUT
4 4 LH CONSOLE HARNESS
40 0.8WOr 3 3
6 PRE-HEAT
49 0.8L 2 2 CN-4 NO. DESTINATION
5 WASHER SIG
48 0.8W 1 1
4 WIPER MOTOR DRIVE 1 1 NC
50 0.8Br
3 INT. SIG EMERGENCY ENGINE STOP SW 2 2 NC
39 0.8VW
2 WORK LIGHT OUT 3 3 NC
38 0.8BrW
4 NC
36E
36E
25
68
18
0.8Y 4 4 0.8Y
63
31
51
17
35
12
53
16
37
37E
0.8ROr
0.8BOr
0.5BW
0.5GY
CS-29
0.5YL
6 6 0.8Grw
0.5LY
0.8Grw
0.5Lg
0.8Or
0.5V
0.5V
0.8G
7 MCU_DECEL
0.8V
0.5B
0.8Y
0.8V
0.8B
1 7
decel R 0.8B 7 7 0.8B
2 8 8 MCU_SIG.GND
CS-19 0.8L 8 8 0.8L
CN-246
9 NC
CN-27A
CN-27
9
2 L 0.8L 9 9 0.8L
1
4
5
10
11
12
13
14
15
16
2
4
5
8
3
6
10
1
2
3
4
5
6
7
9
8
10 10 NC
0.8Gr 10 10 0.8Gr
1 Gr
11 11 NC
0.8Gr 11 11 0.8Gr
REMOCON GND
12 12 NC
SPK FRT RH+
REMOCON+
CS-4 13 13 NC
USB(GND)
BACK UP+
AUX GND
AUX GND
TEL MUTE
USB GND
0.8B 12 12 0.8B
USB(D+)
B C
USB(D-)
ANT 12V
14 GND
USB D+
AUX S1
A
USB 5V
AUX S2
14
USB D-
RH SIDE HARNESS
AUX R
AUX L
USB+
0.8V 13 13 0.8V
B 15 NC
GND
15
ACC
ILL+
NC
NC
NC
NC
ILL-
0.8G
NC
NC
NC
0.8G 14 14
A C 16 16 SAFETY SOL
USB & SOCKET ASSY REMOTE ASSY CASSETTE RADIO SAFETY SW
1409S4EC02
4-4
·ELECTRICAL
ELECTRICAL CIRCUIT(1/2
CIRCUIT CLUSTER TYPE 2)
2
AC
COMP RY
R/DRYER 5R 146 146 5R
CS-74
1
87a 87 85
30 86
WASHER P/P 145 5W 143 5R
2
Pa
POWER RY
M
MASTER SW CABIN LAMP RY 138 2WR CS-74A
CN-22
CN-29
FUSE BOX
DO-5
CR-7
87a
CN-95
30
2
1
86
87a 87 85
85
87
30 86
1
2
MASTER SW
1
5W 145
87a 87 85
30 86
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
2
3
4
5
6
7
8
9
2
5W 144
30A
ROOM LAMP/CASSETTE 10A
30A
30A
20A
10A
10A
10A
20A
10A
10A
10A
30A
20A
30A
30A
10A
20A
30A
20A
10A
20A
10A
20A
20A
20A
20A
20A
10A
20A
10A
1
0.8GrW
0.8GrW
CR-35
0.8V
148A 0.8L
148E 0.8L
0.8V
0.8V
0.8
0.8
FUSIBLE LINK
0.8
87a
30
CR-9
86
85
87
CABIN LAMP(OPTION)
87a
5R 143
30
86
85
87
2
OPTION(BEACON)
AIR CON/HEATER
5R 142
149
150
BATTERY
39E
CN-11
13A
149
39A
NO. DESTINATION 1
SWITCH PANEL
FUEL CUT-OFF
60
CS-74B
13
34 0.8WOr
FUEL HEATER
2B 129
138 2WR
FUEL HEATER
AC& HEATER
G3 0.8B
START,STOP
CONVERTER
SAFETY SOL
TRAVEL SOL
WORK LAMP
1 AC GND 1 CN-60
30 0.8Gr
SOLENOIDE
24 2W
MCU CONT.
HEAD LAMP
60B
START KEY
60R
140A 0.8R
FUEL HEATER FUEL PUMP
CASSETTE
IG POWER
1
2
PRE-HEAT
140 2R
21 2V
CLUSTER
2 BLOWER SIG. 2
FUEL P/P
2L 148
OPTION
87a 87 85
30 86
SPARE
SPARE
WIPER
SPARE
3 AC 24V 3
WIPER
CIGAR
M
CN-36
HORN
MCU
CN-96
CR-1
2W
2W
4 REVERSE FAN 4
3Y 147
12V X 2
5 AC CONTROLLER B+ 5 G23 1.2B
CR-46
2
1
CN-61
0.8 150
87a
6 AC COMP 6 141 1.2G TO:STARTER "B" TERM.
30
86
85
87
78 1.2R
1.2ROr
25 0.8Y
39 0.8GrW
79 1.2RW
32 0.8RW
0.8Gr
1.2Or
1.2Gr
1.2Or
50 1.2Br
1.2Br
24 2W
23 2W
130 2RW
12 0.8R
1
17 1.2V
0.8V
1.2V
2
131 2.0Y
147 3Y
0.8L
2Br
7 AC CONDENSOR FAN 7
2B
26 0.8
140 2R
2Y
0.8ROr 10E
87 2L
2L
8 ILLUMINATION 8
BATT RY
0.8V
124
148
134
104
132
126
0.8L
2B
2Y
G31
2Br
18
16
20
47
133
AIR-CON HARNESS
2L
5
DO-3
141E 0.8G
87A
2
133
122
0.8B 4
87
G24 0.8B
G21
126
1
CN-5
0.8Y 1
1 CLUSTER_TX 1
0.8L 2
2 CLUSTER_RX 2
SH 3G
3 SHIELD 3
0.8B 4
4 CLUSTER_GND 4
0.8Gr 5
5 CLUSTER_IG 5
0.8RW 6
6 NC 6 CD-44
7 NC 7 80H 1.2ROr
A SUPPLY
8 NC 8 91 1.2LW
0.8BW 82 B SIG
9 P_DUMP(SERVICE CONN.) 9 81H 1.2BW
0.8Br 7 C RETURN
10 QUICK COUPLER SW_NO 10
0.8Br 7 A3
11 OVERLOAD SW_COM 11
0.8ROr 00
12 OVERLOAD SW_NO 12
0.8ROr 10A
13 ILLUMINATION 13 CD-18
0.8W 11
14 HOUR METER SIG. 14 1 1.2GrW
0.8G 74 Pa
15 RS232 RX(SERVICE CONN.) 15
0.8R 73
16 RS232 TX(SERVICE CONN.) 16
0.8B 3F
17 GND(SERVICE CONN) 17 ENG OIL PS
0.8R 12
18 WIPER CONT_BATT.24V 18
0.8V 13
19 WIPER CONT_WASHER P/P DRIVE 19
CN-28
20 CAN_Hi(SERVICE CONN) 20 2 1.2VW
1
21 CAN_Lo(SERVICE CONN) 21
22 CAN SHIELD 22
23 23 AC COMP
0.8GrW 39 CN-2
24 WIPER IG 24 1.2GrW 1
1.2ROr 104 46 0.8Y
25 OPTION SW 25 1
1.2B 15 2
26 GND 26 1.2VW 2
1.2Gr 16 60 0.8V
27 CIGAR LIGHTER_IG 27 3
1.2V 17 00 0.8 1.2 00
28 DC-DC CONVERTER 24V 28 4
1.2Or 18 5
29 SPARE SW_COM(IG) 29
1.2B 19A 6
30 GND 30 19 2B
1.2B 19E 7
31 GND 31
32 NC 32 8 CN-75
1.2Br 20 56 Or 1.2Or 6 6 1.2Or
33 BEACON SW_COM(IG) 33 9 2
1.2V 21A 21 2V 75 Br 1.2Br 7 7 1.2Br
34 CABIN LIGHT 34 10 1
0.8BOr 22 8 Y 1.2Y 8
35 START KEY SW_START 35 11 EPPR VALVE
1.2W 23 9 L 1.2L 9
36 START KEY SW_COM 36 12
00 0.8 1.2 00 CD-17
37 NC 37 13 8 1.2Y
21E 2
m
0.8V 14 1.2L
rp
38 CABIN LIGHT 38 00 9
00 0.8 1.2 1
39 NC 39 15
40 NC 40 SPEED SENSOR
41 NC 41 REAR ENGINE HARNESS
42 NC 42 CN-45
CR-23
43 NC 43 CN-3
2.0
1
2.0 10 10 B
1 M
44 NC 44
64E 0.8 1.2 11 11 Gr M
45 NC 45 2 2
0.8Y 25 66 0.8W 1.2 12
46 CASSETTE RADIO_BATT.24V 46 3
0.8V 26 67 0.8Y 1.2 13 START RY B+
47 CASSETTE RADIO_IG 47 4
48 CASSETTE RADIO_GND 48
0.8B 27 81A 0.8
5
1.2 14 FROM BATT.RY STARTER
0.8BrW 28 43 0.8 1.2 15
49 SWITCH PANEL_HEAD LIGHT 49 6
0.8VW 29
50 SWITCH PANEL_WORK LIGHT 50 7 15 R
RS-1 CN-74
51 NC 51 8 16
52 NC 9 2 B+
52 3W/300 12A
0.8 84 1 G
53 BREAKER SW 53 10 1 P
0.8 84 2.0 2.0 1.2W
54 SWITCH PANEL_PREHEAT 54 11 12 3~
0.8Gr 30 2 L
55 SWITCH PANEL_CABIN LAMP 55 12 U
0.8RW 32 3 FI
56 SWITCH PANEL_TRAVEL ALARM 56 4 NC
0.8RW 32 CR-24
57 SWITCH PANEL_IG 57
0.8B 33 15R ALTERNATOR
58 SWITCH PANEL_GND 58 13 V
0.8WOr 34
59 START SW_ACC 59
0.8GW 35 15R
60 START SW_BR 60
PRE-HEAT RY Pre-heater
LW
Gr
CN-8
B
1 NC 1
CD-8
CN-79
2 NC 2 G H F 14 B
3 NC 3 1 C
15 G
4 NC 4 2
0.8 18
5 GND 5 FUEL CUT OFF SOL WATER TEMP SENDOR
6 NC 6
0.8 18
7 ILLUMINATION 7
8 NC 8
9 NC 9
10 NC 10
CR-36
55 0.8BOr
11 NC 1
11 132A 0.8L 4 5 1
12 NC 2
12 132 0.8L
3
CN-7 4
1 NC 1 67 0.8Y 3 2
5
2 NC 2 PRE-HEAT RY
3 NC 3
0.8 18 CR-5
4 SEAT HEAT 4 131 2.0
0.8Or 18 30
5 BREAKER SW 5 22 0.8BOr 87a 87 85
0.8BW 40 86
6 BREAKER SW 6 64 2.0
0.8B G42 87
7 HORN 7 123 0.8Br
0.8GrW 41 85
8 HORN 8 30 86
87a
9 BUTTON 2 9
10 BUTTON 2 10 ANTI-RESTART RY
11 BUTTON 1 11 CR-13
50 1.2Br
12 BUTTON 1 12 30
50A 0.8Br 87a 87 85
13 NC 13 86
0.8Gr 42 10 1.2ROr
14 ACCEL DIAL SUPPLY 14 87
0.8W 99 28 0.8BrW
15 ACCEL DIAL SIGNAL 15 85
0.8B 37 30 86
16 ACCEL DIAL GND 16 87a
CR-2
41 0.8GrW
1
124A 0.8V 4 5 1
CN-140 2
B 152 124 0.8V
1 3
0.8Br 7 4 G12 0.8B
CN-25
2 127 0.8G 2
5 3 2 127 0.8G
QUICK CLAMP 1
HORN RY HORN
CD-10 G13 0.8B
1.2B 81S 2
Pa 1.2YOr 83 127 0.8G
1
0.8Br
CN-20
0.8B
AIR CLEANER SW
CD-2
CN-66
0.8B 81R
1
1
2
0.8 100
2
FUEL LEVEL
CD-1 BREAKER SOL
0.8B 81
C 1 0.8 101
2
HYD TEMP
CD-31
LW 84
Pa 2
B 12J
1
OVERLOAD PS
81H
80A
BR/OR 27
81J
2B
80
90
91
117
8A
Y/W 26
34
OR/W 28
GY/W 30
14
47
16
38
39
40
31
45
36
13
11
29
25
33
65
67
12
32
G/W 55
BR/W 60
L/W 63
W/OR 61
Y/W 62
Y/W 62
50
57
37
54
64
51
44
46
66
68
69
71
72
73
48
42A
1.2ROr 2A
1.2BW 4A
1.2ROr 2
1.2BW 4
1
3
G/OR
B/OR
37A
R/W
B/W
B/W
V/W
0.8OrW
0.8ROr
0.8ROr
63
54
36
OR
OR
GY
GY
BR
BR
BR
0.8BW
0.8BW
0.8LW
W
W
W
G
G
R
R
Y
B
Y
B
L
L
1.2G
105
104
1.2L
0.8Or 47G
47H
0.8Gr
106
47A
0.8V 70
0.8GOr 118
0.8BrW 119
134
CN-51
CN-50
47
49
W
G
V
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
CD-7
0.8RW
CD-6
CD-42
CD-43
0.8Rw
0.8W
1.2G
CN-76
1.2V
C
0.8Or
SUPPLY A
RETURN B
SUPPLY A
RETURN B
0.8Or
RETURN C
RETURN C
SUPPLY A
B
SUPPLY A
B
0.8Or
FUEL LEVEL SENSOR
GND(PRES.SENSOR)
TACHO SENSOR(+)
TACHO SENSOR(-)
CN-81
ANTI-RESTART RY
WATER LEVEL SW
ENG PREHEATER
PROGRAM DUMP
TRAVEL BUZZER
POWER MAX SW
GND (POT&DIAL)
SIG
CN-133
BATTERY 24V(+)
CN-70
MAX FLOW SOL.
ACCEL DIAL SIG
2
1
CN-88
M+
CN-68
P+
NC
CN-135
M-
OVERLOAD SIG
SIG
SIG
P-
SIG
SIG
GND (SENSOR)
1
2
1
P1 PRESS SIG.
P2 PRESS SIG.
P3 PRESS SIG.
O/T DECEL SW
2
PUMP EPPR(+)
5V (POT&DIAL)
1
2
1
2
PRE-HEAT SW
1
FUEL HEATER
PUMP EPPR(-)
ACCEL ACT(+)
2
HOUR-METER
ACCEL ACT(-)
WORKING PS
RS232 (GND)
1
5
TRAVEL PS
ENG OIL PS
GND (MAIN)
2
SERIAL-RX
ALT LEVEL
SERIAL-TX
POWER IG
P2 P1 TRAVEL WORK
M
RS232 (+)
RS232 (-)
POT-SIG
PRESS PRESS
6
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
4-5
·ELECTRICAL
ELECTRICAL CIRCUIT(2/2
CIRCUIT CLUSTER TYPE 2)
2
Service Tool DC/DC CONVERTER CIGARLIGHT RELAY
OVERLOAD SW INTAKE M/ACT TEMP M/ACT MODE(D/FOOT) MODE(VENT)
12V SOCKET HOUR METER BLOWER
24V
12
RS232 P_DUMP
12
10
3
4
9
ECONO SWITCH
12V
2 7 2 7
BLOWER
h
1 4 1 4
12
RS232_RX
3
12
M 3 M
1
3 M
RS232_TX
M 7 7
10
3
4
9
CAN2_Lo
CAN2_Hi
CN-48
GND
CAN_Lo
CAN_Hi
5 5
12V
24V
CL-2
CN-139
IG 24V
M
4
2
GND
CN-138
5
6
7
5
6
7
5
6
7
1
2
3
4
5
6
7
1
2
3
4
1
2
3
4
1
2
3
4
3
2
1
CS-67
11
1
1
2
8
CS-50
C
A
B
1
1
2
1
4
2
3
10
11
12
CN-21
9
4
8
1
2
3
6
7
11
1 12
1.2Gr
1
1.2B
2
ROr
0.8W
CS-52
WIPER CUT
0.8B
0.8Y
3 1 00
G
0.8G
B
E
A
F
10
11
1.2Or
12
J
R 10
9
3
24M 1.2B
1
2
3
6
7
1.2Or
1.2V
24L 1.2B
0.8VOr
2
CS-53
9 0.8Br
0.8Or
0.8Or
0.8Br
Gr 12 4
24Q
0.8V
24R 0.8B
12B
5 3
35E
24V
21
13
R 4A 5
1 0.8BW
60
0.8Or
27F 0.8Br
4
60
22
0.8G
0.8G
0.8B
24T 0.8B
6 0.8G
6 0.8G
6 0.8G
6 0.8G
2 0.8G
3 0.8R
5 0.8V
4 0.8B
4 G 8 6
61
11
27
10
61
5 3
L 9
23F 0.8Or
7 7 AIR-CON HARNESS
B
6 M 2 6 23F 0.8Or 9
62
62
CN-126
Or
8
7
2A
4 CN-11 NO. DESTINATION
10
9
8
7
6
5
4
9 8
3
2
1
1 GND
11
WIPER MOTOR 10 1
10
9A 0.8Br 2 2 BLOWER SIG
11
0.8BW
24S 0.8B 11 12 3 3 FUSE(IG)
0.8G
0.8G
0.8R
0.8V
0.8B
12
4 4 REVERSE FAN
CN-141 QUICK CLAMP SW
G 8 5 5 FUSE(Battery)
59
73
72
71
70
69
FEED BACK 1
W 1 6 6 DPS(COMPRESSOR)
MOTOR DRIVE SIG 2 CN-17 CN-113
3
L 9 00 0.8B 7 7 CONDENSOR FAN
MOTOR DRIVE- 1
R 10 1 W 0.8W 48 1 8 8 ILLUMINATION
MOTOR DRIVE+ 4 2 00 0.8G
B 2 2 B 1.2B 24B 2
GND 5 3
GrW 3 3 GrW 0.8ROr 65 BUZZER
VCC 6 4
R 4 4 R 0.8R 14
CONTINUE 24V 7 5
V 5 5 V 0.8V 15
WASHER P/P 8 6
L 6 6 L 0.8L 49
WASHER SIG. 9 7
Br 7 7 Br 0.8Br 50
INT. SIG 10 8
Or 11
WIPER CUT SW 11
N.C 12
Gr 12
FEED BACK 13 WIPER MOTOR HARNESS
WIPER MOTOR CONT. CN-56A
17 BR RR
1 POWER IG(24V)
10
11
12
13
14
15
16
17
18
10
11
12
13
14
18 B
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
2 GND
19 Y
3 RX
20 L
0
0
0
0
TEMP MOTOR ACT(+)
DUCT SENSOR(GND)
TEMP MOTOR ACT(-)
DPS(COMPRESSOR)
MODE M/ACT(FOOT)
4
1
2
BLOWER RELAY(Lo)
TX
INLET MOTOR(REC)
INLET MOTOR(FRE)
MODE M/ACT(PBR)
MODE M/ACT(DEF)
AMBIENT SENSOR
TEMP M/ACT(PBR)
CONDENSOR FAN
MOTOR ACT(REF)
DUCT SENSOR(+)
W/TEMP SENSOR
MODE M/ACT(M+)
POWER TR BASE
MODE M/ACT(M-)
FET(FEED BACK)
CLUSTER
INCAR SENSOR
REVERSE FAN
ILLUMINATION
ILLUMINATION
CS-82 CN-5
BATTERY(+)
FET(GATE)
POWER TR AMBIENT INCAR W/TEMP
POWER IG
0.8B 20E 1 0.8Y
12 1 1 MCU_RX
12 11 0.8LW 26A 2 0.8L DUCT SENSOR SENSOR SENSOR
IG 24V
11 2 2 MCU_TX
GND
3 SH SENSOR
NC
NC
NC
10 3 3 MCU_GND
10 4 0.8B
8 9 4 4 GND
4 1.2ROr 19A 5 0.8Gr
FUSE
AC & HEATER CONTROLLER(auto)
8 5 5
9
7 7 6 6 NC
3 7 0.8B CS-1
6 7 7 NC CN-24
8 Gr 11 0.8G 2
0.8Or 2
5 8 8 NC CN-10 NO. DESTINATION
1.2LW 26 59 0.8BW 0.8V 3
4 9 9 P_DUMP(MCU) 1
9 0.8Br CL-1 1 1 NC
3 10 10 QUICK COUPLING SOL DOOR SW Gr 11 SPEAKER-RH
10 0.8V 3 2 2 NC
2 11 11 OVERLOAD PS 0.8Y 1 1 0.8Y
12 1 11 0.8VOr 2 3 3 FUSE
1 12 12 MCU_OVERLOAD 0.8B 6 2 0.8G
12 0.8ROr 1 4 4 CASSETTE_RH-
SPARE SW 13 13 HEAD LAMP RY 3 0.8V
13 0.8W CN-23 ROOM LAMP 5 5 CASSETTE_RH+
14 14 MCU_HOURMETER 0.8Y 4 4 0.8Y
69 0.8G 2 6 6 CASSETTE_LH-
15 15 RS232_RX(MCU) 0.8L 5 5 0.8L
70 0.8R 1 7 7 CASSETTE_LH+
16 16 RS232_TX(MCU) 6 2.0B
71 0.8B SPEAKER-LH 8 8 GND
17 17 GND 7 2.0B
14 0.8R CL-7 9 9 GND
18 18 FUSE 1.2BrW 8 8 1.2BrW
15 0.8V 10 10 BEACON SW
19 19 WASHER P/P M 1.2B 6A 9 2.0V
72 0.8V 11 11 CABIN LIGHT RY
20 20 CAN_Hi 10 2.0V
73 0.8G BEACON LAMP 12 12 CABIN LIGHT RY
21 21 CAN_Lo
74 SH
22 22 Shieeld CL-8
2.0V 9 10 2.0V
CL-9 CABIN HARNESS
23 23 NC 2 2
65 0.8ROr 1.2B 6B 7 1.2B
24 24 WIPER FUSE 1 1
19 1.2ROr
25 25 FUSE CABIN LIGHT CABIN LIGHT
26 26 GND
21 1.25Gr
27 27 FUSE CS-83
22 1.2V 0.8B 19G ACCEL DIAL LED
CS-23 28 28 FUSE 12 CS-26A
CN-279
0.8B 24J 23 1.2Or 12 11 0.8Or 18A 5E 0.8BW
12 29 29 FUSE 11 2
1
2
12 11 0.8BrW 58A 24A 1.2B 4E 0.8G
11 30 30 GND 10 1
24E 1.2B 10 0.8G 15
0.8ROr
10 24 2B 31 31 GND 8 9
0.8B
10 4 0.8V 16 BREAKER SW
8 9 32 32 NC 8
4 1.2Br 27E 27 1.2Br 9 0.8BrW 17
8 33 33 FUSE 7 7 CN-156
19F
19 1.2B
32
9 28 2V 28A 1.2V 3
7 7 34 34 CABIN LAMP RY 6 2
3 29 1.2BOr 31 1.2ROr
6 35 35 ANTI RESTART RY 5 1
30 1.2W 0.8Or 18
5 36 36 FUSE 4
20
AIR SEAT
1.2BrW 58 0.8Gr
4 37 37 NC 3 CN-8 NO. DESTINATION
28E 0.8V
3 38 38 CABIN LAMP RY 2 15 0.8G
12 1 1 1 NC
2 39 39 NC 1 16 0.8V
12 1 2 2 FUSE
1 40 40 NC SPARE SW 17 0.8BrW
3 3 CRAB COM
41 41 NC 18 0.8Or
BEACON LAMP SW CS-99 4 4 NC
42 42 NC 0.8B 19A 19 1.2B
CS-27 12 5 5 NC
0.8B 24J 43 43 NC 12 11 0.8GW 21A 20 0.8Gr
12 11 6 6 CRAB SIG_MCU
12 11 0.8BrW 58A 44 44 NC 32 0.8ROr
11 10 7 7 ILLUMINATION
45 45 NC 10 22 0.8L
10 35 8 9 8 8 NC
10 0.8Y 4 0.8L 22 23 0.8VW
8 9
46 46 FUSE 8 9 9 DPF REGEN
4 36 0.8V 0.8L
0.8 27E 47 47 FUSE 9 22A 24 0.8R
8 37 0.8B 7 7 10 10 DPF COM
9 48 48 GND 3 25 0.8LW
7 7 38 6 11 11 DPF INHIBIT
0.8BrW 26 0.8RW
3 49 49 HEAD LAMP RY
6 39 5 12 12 AIR COMP RY
0.8VW 0.8GW 21
50 50 WORK LAMP RY 4
5
4
0.8 58 51 51 NC 3
0.8RW 26
RH CONSOLE HARNESS
52 52 NC 2
3 40 0.8 12 1
53 53 BREAKER SW(JOYSTICK) 1
2 40 0.8WOr
12 1 54 PRE-HEAT
54
1 41 0.8Gr SPARE SW
55 55 CABIN LAMP RY
BREAKER SW 42 0.8YW CS-100
56 56 MCU_TRAVEL ALARM SW
CN-10 43 0.8RW 1 CN-7 NO. DESTINATION
57 57 FUSE
1 NC 1 44 0.8B 2 1 1 NC
58 58 GND
2 NC 2 45 0.8WOr 3 2 2 NC
0
0.8Y 35A 59 59 POWER RY 0.8VW 23
3 ROOM LAMP 24V 3 46 0.8GW 4 3 3 NC
51 60 BATT. RY
0,1
0.8G 60 31 1.2ROr
4 SPEAKER RH- 4 5 4 4 FUSE
0.8V 53 R 0.8R 24 0.8G 4 4 0.8G
5 SPEAKER RH+ 5 4 6 1 5 5 BREAKER SW
0.8Y 52 BREAK B 0.8BW 5 5 0.8BW
6 SPEAKER LH- 6 6 7 2 6 6 BREAKER RY
0.8L 55 0.8R 24A CS-26 0.8B 6 6 0.8B
7 SPEAKER LH+ 7 8 1 7 7 GND
1.2B 24F 24 2B CS-2 HORN R 0.8Grw 7 7 0.8Grw
30 1.2W
H0 I
8 GND 8 10 I 9 2 8 8 HORN RY
1.2B 24G 1 0.8LW 25 CS-5 0.8L 8 8 0.8L
9 GND 9 46 0.8GW 8 10 9 9 NC
0, I
1.2BrW 58 2 2 L 0.8L 9 9 0.8L
10 BEACON LAMP 10 47 1.2R 11 10 10 NC
3 4
H BRACC
1.2V 28F 28 2V 12 11 0.8Br 30 0.8Gr 10 10 0.8Gr
11 CABIN LIGHT 11 12 11 11 NC
1.2V 28G 4 1 1 Gr
B
2 0.8Gr 11 11 0.8Gr
12 CABIN LIGHT 12 3 SPARE SW 12 12 NC
5
HARNESS CABIN 29 1.2BOr CN-142 13 13 AIR COMP RY
6 0.8Gr 12 12 0.8Gr
+ A 14 MCU_5V
STC
5 14
6 0.8W 13 13 0.8W
S B 15 15 MCU_ACCEL SIG.
0.8B 14 14 0.8B
START KEY SW - C 16 16 MCU_SUPPLY GND
CN-116 ACCEL DIAL
12 NC
44 0.8B
11 GND
43 0.8RW
10 POWER 24V CS-33
9 NC 6 6
42 0.8YW 5 5
8 TRAVEL ALARM
41 0.8Gr
7 CABIN LIGHT OUT 4 4 LH CONSOLE HARNESS
40 0.8WOr
6 PRE-HEAT 3 3
49 0.8L
5 WASHER SIG 2 2 CN-4 NO. DESTINATION
48 0.8W
4 WIPER MOTOR DRIVE 1 1 1 1 NC
50 0.8Br
3 INT. SIG EMERGENCY ENGINE STOP SW 2 2 NC
39 0.8VW
2 WORK LIGHT OUT 3 3 NC
38 0.8BrW
36E
36E
25
68
18
63
31
0.8Y 4 4 0.8Y
51
17
35
12
53
16
37
37E
power
max B 0.8B 5 5 0.8B
MCU_SIG.GND
0.5ROr
6
0.8ROr
2 6
0.8BOr
0.5BW
0.5GY
0.5YL
0.5LY
0.5Lg
cs-29
0.8Or
0.8Grw 6 6 0.8Grw
0.5V
0.5V
0.8G
0.8V
0.5B
0.8Y
0.8V
0.8B
1 7 7 MCU_DECEL
decel R 0.8B 7 7 0.8B
2 8 8 MCU_SIG.GND
cs-19 0.8L 8 8 0.8L
CN-246
CN-27A
CN-27
9 9 NC
2 L 9
1
4
5
10
11
12
13
14
15
16
2
4
5
0.8L
3
9
10
0.8L
3
1
2
3
4
5
6
7
9
8
10 10 NC
0.8Gr 10 10 0.8Gr
1 Gr
11 11 NC
11
REMOCON GND
0.8Gr 11 0.8Gr
12 12 NC
SPK FRT RH+
REMOCON+
13 NC
USB(GND)
CS-4 13
BACK UP+
AUX GND
AUX GND
TEL MUTE
USB GND
USB(D+)
0.8B 12 12 0.8B
USB(D-)
ANT 12V
USB D+
AUX S1
C
USB 5V
B
AUX S2
USB D-
A 14 14 GND
AUX R
AUX L
USB+
0.8V 13 13 0.8V
GND
HARNESS RH SIDE
ACC
15 NC
ILL+
B
NC
NC
NC
15
NC
ILL-
NC
NC
NC
0.8G 14 14 0.8G
A C 16 16 SAFETY SOL
USB&SOCKET ASS'Y REMOTE ASS'Y CASSETTE RADIO SAFETY SW
1409S4EC52
4-6
MEMORANDUM
4-7
1. POWER CIRCUIT (CLUSTER TYPE 1)
The negative terminal of battery is grounded to the machine chassis through master switch.
When the start switch is in the OFF position, the current flows from the positive battery terminal as
shown below.
1) OPERATING FLOW
Battery Battery relay Fusible link [CN-60] Master switch [CS-74]
Fuse box [No.1] Power relay [CR-35 (30)]
Fuse box [No.2] I/conn [CN-5 (46)] I/conn [CN -10 (3)] Room lamp [CL-1 (2)]
Door switch [CS-1]
Radio & USB player [CN-27 (8)]
Fuse box [No.3] MCU [CN-51 (1)]
Fuse box [No.4] Master switch [CS-74B] l/conn [CN-5 (36)] Start switch [CS-2 (1)]
RMS [CN-125A (1)]
Fuse box [No.5] l/conn [CN-11 (5)] AC & Heater controller (3)
Blower relay (3)
Fuse box [No.6] I/conn [CN - 5 (18)] I/conn [CN -17 (5)] Wiper motor controller
[CN-141 (7)]
Wiper motor [CN-21 (4)]
Fuse box [No.7] I/conn [CN - 5 (6)] Cluster [CN -56 (1)]
2) CHECK POINT
Engine Start switch Check point Voltage
4-8
CS-74
MASTER SW
CN-141 CN-5
RW
R
2
1
CONTINUE 24V 7
1 2W CR-35
CS-74B
8
7
6
5
4
3
2
1
2 30
0.8WOr 87a 87 85
CN-56
86
CONTROLLER
CN-17 3
WIPER MOTOR
2WR
RR
RR
RR
RR
RR
RR
RR
RR
2W
2W
CN-21 1 87
4 0.8B
0.8Gr
2 85
3 1 5
0.8RW 30 86
POWER RY
87a
2 3 6
TX
RX
SIG_2
GND
SIG_3
IG 24V
3 4 7
BATT.24V
5
R
CLUSTER
CAMERA SIG
4 5 8
4 CN-36
5 6 9 30A
2W IG POWER
6 2 6 7 17 1
M 0.8R 0.8Y ROOM LAMP/CASSETTE 10A
WIPER MOTOR
8 18 2
1.2R MCU 30A
19 3
2W START KEY 30A
CN-138 20 4
6
5 3Y 20A
ST C
CS-2 AIR CON & HEATER
5R
12V 12V C 21
1.2V 1.2V 5
6 24V A 28 0.8R WIPER 10A
6
3 5 24V GND B 29 0.8RW CLUSTER 10A
DC & DC
2 7
BR ACC
1 4 30 0.8Gr 10A
CLUSTER
CONVERTER
1.2R 8
H
4 3 31 20A
MCU CONT.
9
0, I
2
2WR
32 10A
1.2W MCU EPPR
1 33 10
START KEY SW
POWER CIRCUIT (CLUSTER TYPE 1)
10A
H 0 I
SWITCH PANEL
34 11
CASSETTE 10A
35 12
1.2W 30A
2
CN-27
9
8
7
6
5
4
3
FUEL CUT-OFF SOL
12
11
10
36 13
ACC 1 1.2V CONVERTER 20A
37 14
CN-125A
NC
NC
ILL- 2 38 WORK LAMP 30A
RMS
15
NC 3 39 CABIN LAMP(OPT) 30A
CN-126
KEY "IG"
4-9
16
MAIN GND
MAIN GND
SPK FRT RH- 4 42 WIPER 10A
10
RX232(2)-TX
RX232(1)-TX
RX232(1)-RX
RX232(2)-RX
0.8G 17
RX232(2)-GND
RX232(1)-GND
SPK FRT LH- 5 43 9 J IG 24V HEAD LAMP 20A
0.8G 18
BATTERY POWER
TEL MUTE 6 44 8 H CAN2_Lo 30A
0.8G FUEL HEATER
ANT 12V 7 45 7 G CAN2_Hi 19
0.8Y 0.8Y 0.8G START. STOP 20A
BACK UP+ 8 46 6 F CAN_Lo 20
5W
3 C RS232_TX
5
57
4
1
9
8
7
6
3
23
12
11
10
SPK FRT RH+ 11 0.8G
2 B RS232_RX OPTION 20A
CN-10
58
0.8Y
SPK FRT LH+ 14 26
BEACON LAMP(OPT) 20A
Gr
1
2
3
Gr
NC 15 27
0.8Y
TRAVEL SOL 20A
GND 16 28
CR-1
CN-48
PRE-HEAT 10A
1
2
3
29
h
CL-1
20A
BATT RY
FUEL P/PUMP
30
CS-1
SPARE 10A
DOOR SW
HOUR METER 31
FUSE BOX
ROOM LAMP
CN-11
2
MANUAL RESET
1
CIRCUIT BREAKER
CS-74A
60R
BATTERY(+)
(AUTO)
3 2 5R
3 1
5R
1
2
1
2
4 2
CS-74
AC & HEATER
3Y
CN-60
CN-95
CONTROLLER
FUSIBLE LINK
5
MASTER SW
(12VX2)
5R
5R
5W
5W
6
BATTERY
1 2 1 7
4
8
60B
2
1
1409S4EC03
3 4 4 CN-51
1.2R
BLOWER RY
BATTERY 24V (+) 1
MCU
2. POWER CIRCUIT (CLUSTER TYPE 2)
The negative terminal of battery is grounded to the machine chassis through master switch.
When the start switch is in the OFF position, the current flows from the positive battery terminal as
shown below.
1) OPERATING FLOW
Battery Battery relay Fusible link [CN-60] Master switch [CS-74]
Fuse box [No.1] Power relay [CR-35 (30)]
Fuse box [No.2] I/conn [CN-5 (46)] I/conn [CN -10 (3)] Room lamp [CL-1 (2)]
Door switch [CS-1]
Radio & USB player [CN-27 (8)]
Fuse box [No.3] MCU [CN-50 (7)]
Fuse box [No.4] Master switch [CS-74B] l/conn [CN-5 (36)] Start switch [CS-2 (1)]
Fuse box [No.5] l/conn [CN-11 (5)] AC & Heater controller (3)
Blower relay (3)
Fuse box [No.6] I/conn [CN - 5 (18)] I/conn [CN -17 (5)] Wiper motor controller
[CN-141 (7)]
Wiper motor [CN-21 (4)]
Fuse box [No.8] I/conn [CN - 5 (5)] Cluster [CN -56A (1)]
2) CHECK POINT
Engine Start switch Check point Voltage
4-10
CS-74
MASTER SW
BR
CN-141 CN-5
R
2
1
CONTINUE 24V 7
4
3
2
1
1 2W CR-35
CS-74B
2 30
CN-56A
0.8WOr 87a 87 85
86
CONTROLLER
CN-17
RR
3
WIPER MOTOR
2WR
2W
2W
CN-21 1 87
4 0.8B
0.8Gr
2 85
3 1 5
30 86
POWER RY
87a
2 3 6
TX
RX
GND
3 4 7
CLUSTER
5
R
8
POWER IG(24V)
4 5
4 CN-36
5 6 9 30A
2W IG POWER
6 2 6 7 17 1
M 0.8R 0.8Y ROOM LAMP/CASSETTE 10A
WIPER MOTOR
8 18 2
1.2R MCU 30A
19 3
2W START KEY 30A
CN-138 20 4
6
5 3Y 20A
ST C
CS-2 AIR CON & HEATER
5R
12V 12V C 21
1.2V 1.2V 5
6 24V A 28 0.8R WIPER 10A
6
3 5 24V GND B 29 SPARE 10A
DC & DC
2 7
BR ACC
1 4 30 10A
0.8Gr CLUSTER
CONVERTER
1.2R 8
H
4 3 31 20A
MCU CONT.
POWER CIRCUIT (CLUSTER TYPE 2)
0, I
2
2WR
32 10A
1.2W FUEL CUT-OFF SOL
1 33 10
START KEY SW
10A
H 0 I
SWITCH PANEL
34 11
CASSETTE 10A
35 12
CN-27 1.2W START. STOP 30A
36 13
ACC 1 1.2V CONVERTER 20A
37 14
ILL- 2 38 WORK LAMP 30A
15
4-11
NC 3 39 CABIN LAMP(OPT) 30A
CN-126 16
SPK FRT RH- 4 42 WIPER 10A
10
0.8G 17
SPK FRT LH- 5 43 9 J IG 24V HEAD LAMP 20A
0.8G 18
TEL MUTE 6 44 8 H CAN2_Lo 30A
0.8G FUEL HEATER
ANT 12V 7 45 7 G CAN2_Hi 19
0.8Y 0.8Y 0.8G SPARE 20A
BACK UP+ 8 46 6 F CAN_Lo 20
5W
3 C RS232_TX
5
57
4
1
9
8
7
6
3
23
12
11
10
SPK FRT RH+ 11 0.8G
2 B RS232_RX OPTION 20A
CN-10
58
0.8Y
SPK FRT LH+ 14 26
BEACON LAMP(OPT) 20A
Gr
1
2
3
Gr
NC 15 27
0.8Y
TRAVEL SOL 20A
GND 16 28
CR-1
CN-48
PRE-HEAT 10A
1
2
3
29
h
CL-1
20A
BATT RY
FUEL P/PUMP
30
CS-1
SPARE 10A
DOOR SW
HOUR METER 31
FUSE BOX
ROOM LAMP
CN-11
2
1
CS-74A
60R
BATTERY(+) 3
(AUTO)
2 5R
3 1
1
2
1
2
5R
CN-60
CN-95
4 2
CS-74
AC & HEATER
3Y
FUSIBLE LINK
CONTROLLER
5
MASTER SW
(12VX2)
5R
5R
6
5W
BATTERY
5W
1 2 1 7
4
8
60B
2
1
1409S4EC53
3 4 4 CN-50
1.2R
BLOWER RY
BATTERY 24V (+) 7
MCU
3. STARTING CIRCUIT (CLUSTER TYPE 1)
1) OPERATING FLOW
Battery(+) terminal Battery relay [CR-1] Fusible link [CN-60] Master switch [CS-74]
Fuse box [No.4] Master switch [CS-74B] I/conn [CN-5(36)] Start switch [CS-2(1)]
(1) When start key switch is in ON position
Start switch ON [CS-2 (2)] I/conn [CN-5 (60)] Battery relay [CR-1]
Battery relay operating (all power is supplied with the electric component)
Start switch ON [CS-2 (3)] I/conn [CN-5 (59)]
Power relay [CR-35 (86) → (87)] Fuse box [No.10]
(2) When start key switch is in START position
Start switch START [CS-2 (6)] I/conn [CN-5 (35)] Anti-restart relay [CR-5 (86) → (87)]
l/conn [CN-3 (2)] Start relay [CR-23]
2) CHECK POINT
Engine Start switch Check point Voltage
① - GND (battery)
② - GND (start key)
③ - GND (battery relay M4)
OPERATING START ④ - GND (starter B+) 20~25V
⑤ - GND (starter M)
⑥ - GND (start relay)
⑦ - GND (battery relay M8)
※ GND : Ground
4-12
CN-5
1
MCU
2 CR-35
CS-74 2W
3 30
0.8WOr 87a 87 85
4 86
2WR
MASTER SW
5 87
0.8B
6 85
ANTI RESTARTY RY
2
1
30 86
POWER RY
7 87a
CS-74B
6
8
20
5
ST C
CS-2
2W
2W
9
CN-51
1.2BOr
6 31 CN-36
5
V/W
3 32 2W IG POWER 30A
2
BR ACC
1 4 33 1
1.2R ROOM LAMP/CASSETTE 10A
2
H
4 3 34
0.8GW 0.8BOr MCU 30A
0, I
2 35 3
1.2W 1.2W 2W START KEY 30A
START KEY SW
1 36 4
H 0 I
AIR CON & HEATER 20A
5R
37 5
WIPER 10A
38 6
2
39 CLUSTER 10A
7
57 CLUSTER 10A
8
58 MCU CONT. 20A
0.8WOr 9
2WR
W 15
ALT. LEVEL 27
MCU
CABIN LAMP(OPT) 30A
CN-52 16
WIPER 10A
17
HEAD LAMP 20A
18
FUEL HEATER 30A
4-13
19
START. STOP 20A
20
HORN 10A
0.8
2.0
2W
0.8W
2B
0.8Br
2.0Y
0.8
21
2W
0.8BOr
10A
5
4
1
9
8
7
6
3
2
5
4
1
9
8
7
6
SAFETY SOL
12
11
10
15
14
13
12
11
10
85
86
87
30
23
CR-5
CN-3
CN-2
87a
OPTION 20A
24
1.2
1.2
1.2
20A
2B
SOLENOIDE
2W
25
1.2LW
CIGAR LIGHTER 20A
3 2
4 5 1
26
3
BEACON LAMP(OPT) 20A
27
20A
ANTI-RESTART RY
TRAVEL SOL
1.2B
1.2G
0.8B
0.8G
28
PRE-HEAT 10A
29
2
1
FUEL P/PUMP 20A
CR-1
1.2B
7
30
DO-3
1.2BOr
6
SPARE 10A
RS-1
DIODE 31
3W/300
BATT RY
FUSE BOX
2
1
2
1
16
12A
1
MANUAL RESET
CIRCUIT BREAKER
CR-23
CS-74A
60R
5R
START RY
1
5R
1
2
1
2
CS-74
1.2W
CN-60
CN-95
FUSIBLE LINK
2Br
5
0.8L
0.8V
MASTER SW
4
3
2
1
(12VX2)
5R
5R
5W
5W
BATTERY
L
P
3
FI
4
2
5
1
B+
NC
M
2B
2W
B+
1.2LW
CN-74
CR-51
60B
CN-45
ALTERNATOR
3~
F
G
H
G
U
STARTER
3 2
4 5 1
CN-79
1409S4EC04
FUEL CUT OFF RY
2) CHECK POINT
Engine Start switch Check point Voltage
① - GND (battery)
② - GND (start key)
③ - GND (battery relay M4)
OPERATING START ④ - GND (starter B+) 20~25V
⑤ - GND (starter M)
⑥ - GND (start relay)
⑦ - GND (battery relay M8)
※ GND : Ground
4-14
CN-5
1
MCU
2 CR-35
CS-74 2W
3 30
0.8WOr 87a 87 85
4 86
MASTER SW
2WR
5 87
0.8B
ANTI RESTARTY RY
6 85
2
1
30 86
POWER RY
7 87a
CS-74B
8
11
6
5
ST C
CS-2
CN-50
9
2W
2W
1.2BOr
6 31 CN-36
V/W
3 5 32 30A
2W IG POWER
2
BR ACC
1 4 33 1
1.2R ROOM LAMP/CASSETTE 10A
2
H
4 3 34
0.8GW 0.8BOr MCU 30A
0, I
2 35 3
1.2W 1.2W 2W START KEY 30A
START KEY SW
1 36 4
H 0 I
AIR CON & HEATER 20A
5R
37 5
WIPER 10A
38 6
2
39 SPARE 10A
7
57 CLUSTER 10A
8
58 MCU CONT. 20A
0.8WOr 9
2WR
MCU
15
CABIN LAMP(OPT) 30A
16
WIPER 10A
17
HEAD LAMP 20A
2W
0.8Br
2.0Y
18
0.8BOr
4-15
SPARE 20A
85
86
87
30
20
CR-5
87a
5W
10A
2.0
0.8
2.0
HORN
0.8W
21
AC & HEATER 20A
22
10A
5
4
1
9
8
7
6
3
SAFETY SOL
12
11
10
3 2
4 5 1
23
CN-3
OPTION 20A
24
1.2
1.2
1.2
ANTI-RESTART RY
SOLENOIDE 20A
25
CIGAR LIGHTER 20A
26
3
BEACON LAMP(OPT) 20A
27
TRAVEL SOL 20A
1.2B
1.2G
0.8B
0.8G
28
PRE-HEAT 10A
29
2
1
FUEL P/PUMP 20A
CR-1
1.2B
7
30
DO-3
RS-1
1.2BOr
3W/300
SPARE 10A
2
1
DIODE
31
BATT RY
FUSE BOX
2
1
16
12A
1
CR-23
CS-74A
60R
5R
START RY
1
1
2
1
2
5R
CN-60
CN-95
CS-74
1.2W
FUSIBLE LINK
5
MASTER SW
4
3
2
1
(12VX2)
5R
5R
5W
BATTERY
5W
L
P
FI
B+
NC
M
B+
2B
CN-74
2W
1.2LW
60B
CN-45
ALTERNATOR
3~
G
F
H
G
STARTER
M
CN-79
1409S4EC54
FUEL CUT OFF SOL
5. CHARGING CIRCUIT (CLUSTER TYPE 1)
When the starter is activated and the engine is started, the operator releases the key switch to the
ON position.
Charging current generated by operating alternator flows into the battery through the battery relay
[CR-1].
The current also flows from alternator to each electrical component and controller through the fuse box.
1) OPERATING FLOW
(1) Warning flow
Alternator "L" terminal I/conn [CN-3 (3)] MCU alternator level [CN-52 (27)]
Cluster charging warning lamp(Via serial interface)
2) CHECK POINT
※ GND : Ground
4-16
CN-51
BATT.POWER_24V 1
POWER IG 2 CN-36
POWER_24V OUT 3 IG POWER 30A
TACHO SENSOR+ 4 1
GND_5V 5
ROOM LAMP/CASSETTE 10A
2
POWER_5V OUT 6 MCU 30A
G/A MOTOR(+) 7 3
START KEY 30A
G/A MOTOR(-) 8 4
NC 9 AIR CON & HEATER 20A
5R
NC
5
10 10A
WIPER
SH
GND_MAIN 11 6
0.8L
0.8L
0.8Y
0.8Y
RW
CAN_SHIELD 12 CLUSTER 10A
7
GND_RETURN 13 CLUSTER 10A
8
7
6
5
4
3
2
1
5
4
1
9
8
7
6
3
60
59
58
57
24
23
22
21
20
19
18
17
SPEED SENSOR+(HMC) 14 8
20A
CN-5
MCU CONT.
CN-56
TACHO SENSOR- 15 9
PROGRAM DUMP 16 MCU EPPR 10A
RR
RR
RR
RR
RR
RR
RR
RR
SH
10
0.8L
0.8Y
ONE TOUCH DECEL 17
SWITCH PANEL 10A
POWER BOOS SW 18 11
HOUR METER 19 CASSETTE 10A
TX
12
RX
ANTI RESTARY RY.(F)
SIG_2
GND
20 30A
SIG_3
FUEL CUT-OFF SOL
IG 24V
BATT.24V
MCU
CAN1 Hi 21 13
CLUSTER
20A
CAMERA SIG
NC 22 CONVERTER
0.8L 14
RS485+(TX)-CLUSTER 23 WORK LAMP 30A
RS232C1_TX-HRDT 24 15
CABIN LAMP(OPT) 30A
RS232C2_TX-RCM 25 16
TR ALARM SELECT SIG 26 WIPER 10A
ENG OIL PS 27 17
HEAD LAMP 20A
COOLENT LEVEL 28 18
AIR CLEANER SW(NO) 29 FUEL HEATER 30A
BLOWER SIG.
19
30 START. STOP 20A
CAN1 Lo 31 20
5W
NC 32 HORN 10A
0.8Y 21
RS485-(RX)-CLUSTER 33 20A
CHARGING CIRCUIT (CLUSTER TYPE 1)
AC & HEATER
RS232C1_RX-HRDT 34 22
SAFETY SOL 10A
RS232C2_RX-RCM 35 23
PRE-HEAT SELECT SIG 36 OPTION 20A
ENG.OIL FILTER 37 24
SOLENOIDE 20A
NC 38 25
4-17
NC 39 CIGAR LIGHTER 20A
NC
26
40
0.8B
20A
0.8W
BEACON LAMP(OPT)
27
TRAVEL SOL 20A
28
5
4
1
9
8
7
6
3
12
11
10
PRE-HEAT 10A
CN-3
CN-52 29
W
ALT. LEVER 27 FUEL P/PUMP 20A
1.2
1.2
1.2
30
MCU SPARE 10A
31
FUSE BOX
1.2B
1.2G
0.8G
0.8W
MANUAL RESET
RS-1
1
2
3W/300
CIRCUIT BREAKER
2
1
CS-74
CR-1
1.2B
DO-3
1.2BOr
5R
1
DIODE
BATT RY 5R
1
2
1
2
16
2
CS-74
2
1
12A
CN-60
CN-95
FUSIBLE LINK
MASTER SW
5R
5R
5W
5W
CR-23
60R
START RY
4
1.2W
5
4
3
2
1
(12VX2)
BATTERY
L
P
FI
B+
NC
M
B+
CN-74
60B
ALTERNATOR
CN-45
3~
G
U
STARTER
M
1409S4EC05
6. CHARGING CIRCUIT (CLUSTER TYPE 2)
When the starter is activated and the engine is started, the operator releases the key switch to the
ON position.
Charging current generated by operating alternator flows into the battery through the battery relay
[CR-1].
The current also flows from alternator to each electrical component and controller through the fuse box.
1) OPERATING FLOW
(1) Warning flow
Alternator "L" terminal I/conn [CN-3 (3)] MCU alternator level [CN-51 (9)]
Cluster charging warning lamp(Via serial interface)
2) CHECK POINT
※ GND : Ground
4-18
CN-50 CN-36
BOOM PRIORITY SOL 1
MAX FLOW SOL. 2 IG POWER 30A
1
POWER MAX SOL. 3 ROOM LAMP/CASSETTE 10A
HOUR-METER 4 2
MCU 30A
ENG PREHEATER 5 3
FUEL HEATER 6 START KEY 30A
BATTERY 24V(+) 7 4
AIR CON & HEATER 20A 5R
PUMP EPPR(-) 8 5
NC WIPER 10A
L
9
SH
6
0.8L
0.8Y
PROGRAM DUMP 10 10A
SPARE
ANTI-RESTART RY 11 7
ACCEL ACT(+) 12 CLUSTER 10A
4
3
2
1
5
4
1
9
8
7
6
3
60
59
58
57
24
23
22
21
20
19
18
17
8
TRAVEL SPEED SOL. 13 20A
CN-5
MCU CONT.
CN-56A
NC 14 9
FUEL CUT-OFF SOL 10A
RR
NC 15
SH
10
0.8L
0.8Y
TRAVEL BUZZER 16 SWITCH PANEL 10A
PRE-HEAT SW 17 11
CASSETTE 10A
NC 18 12
NC 19 START. STOP 30A
TX
RX
MCU
13
GND
OVERLOAD SIG 20 20A
CONVERTER
NC 21 14
POWER IG(24V)
CLUSTER
NC 22 WORK LAMP 30A
15
ACCEL ACT(-) 23 CABIN LAMP(OPT) 30A
POWER IG 24 16
WIPER 10A
NC 25 17
NC 26 HEAD LAMP 20A
NC 27 18
FUEL HEATER 30A
GND (MAIN) 28 19
Y
SERIAL-TX 29 SPARE 20A
L 20
SERIAL-RX 30
5W
HORN 10A
GND 31 21
RS232 (+) 32 AC & HEATER 20A
22
CHARGING CIRCUIT (CLUSTER TYPE 2)
4-19
26
0.8B
20A
0.8W
BEACON LAMP(OPT)
27
TRAVEL SOL 20A
28
5
4
1
9
8
7
6
3
12
11
10
PRE-HEAT 10A
CN-3
CN-51 29
W
ALT. LEVER 9 FUEL P/PUMP 20A
1.2
1.2
1.2
30
MCU SPARE 10A
31
FUSE BOX
1.2B
1.2G
0.8G
0.8W
2
RS-1
1
2
3W/300
2
1
CS-74
CR-1
1.2B
DO-3
1.2BOr
5R
1
DIODE
BATT RY
1
2
1
2
5R
16
CN-60
CN-95
2
CS-74
2
1
12A
FUSIBLE LINK
MASTER SW
1
5R
5R
5W
5W
CR-23
60R
START RY
4
1.2W
5
4
3
2
1
(12VX2)
BATTERY
L
P
FI
B+
NC
M
B+
CN-74
60B
ALTERNATOR
CN-45
3~
G
U
STARTER
M
1409S4EC55
7. HEAD AND WORK LIGHT CIRCUIT (CLUSTER TYPE 1)
1) OPERATING FLOW
Fuse box (No.18) Head light relay [CR-13 (30,86)]
Fuse box (No.15) Work light relay [CR-4 (30,86)]
(1) Head light switch ON
Head light switch ON [CN-116 (1)] l/conn [CN-5 (49)] Head light relay [CR-13 (85) → (87)]
Head light ON [CL-3 (1)] , [CL-4 (1)]
l/conn [CN-11 (8)] AC & Heater controller illumination ON [4]
l/conn [CN-5 (13)] Cigar light [CL-2]
Radio & USB player illumination ON [CN-27 (9)]
2) CHECK POINT
Engine Start switch Check point Voltage
※ GND : Ground
4-20
NC
GND
IG 24V
2
1
CN-36
POWER IG
IG POWER 30A
CN-279
BATTERY(+)
1
ILLUMINATION
ILLUMINATION
REVERSE FAN
ROOM LAMP/CASSETTE 10A
INCAR SENSOR
0.8B
AC & HEATER
2
POWER TR BASE
W/TEMP SENSOR
DUCT SENSOR(+)
0.8ROr
CN-246
AMBIENT SENSOR
MCU 30A
0.5YL 3
DUCT SENSOR(GND)
USB(D-) 1
0.5GY START KEY 30A
USB(D+) 2 4
CONTROLLER(AUTO)
0.5ROr AIR CON & HEATER 20A
3
9
8
7
6
5
4
3
2
1
USB(GND)
14
13
12
11
10
5
4 WIPER 10A
AUX S1
6
AUX S2 5 CLUSTER 10A
0.5V 7
USB+ 6 CLUSTER 10A
NC 7 8
CN-5
1.2B
MCU CONT. 20A
0.8ROr
NC 8 9
1 MCU EPPR 10A
NC 9 10
2
2
5
5
4
1
4
1
8
7
6
9
8
7
6
3
3
10 SWITCH PANEL
12
11
10
AUX GND
3 11
CN-8
10A
CN-11
CN-27A CASSETTE
0.5V 4 12
1
0.8
0.8
USB 5V 1 FUEL CUT-OFF SOL 30A
0.5LY 5 13
0.8ROr
USB D- 2 CONVERTER 20A
0.5BW 6 14
USB D+ 3 30A
0.5Lg 2RW WORK LAMP
4 7 15
USB GND
8 CABIN LAMP(OPT) 30A
NC 5 16
6 9 WIPER 10A
AUX L 17
AUX R 7 CL-2 10 1.2Br HEAD LAMP 20A
REMOTE ASSY
18
AUX GND 8 11 FUEL HEATER 30A
19
CN-27 12 START. STOP 20A
ROr 0.8ROr 0.8ROr
ACC 1 13 20
10A
5
HORN
ILL- 2 14 21
CIGAR LIGHT
AC & HEATER 20A
NC 3 15 22
SAFETY SOL 10A
SPK FRT RH- 4 16 23
4-21
OPTION 20A
SPK FRT LH- 5 17 24
SOLENOIDE 20A
TEL MUTE 6 18 25
ANT 12V 7 19 CIGAR LIGHTER 20A
26
BACK UP+ 8 20 BEACON LAMP(OPT) 20A
0.8ROr 27
20A
HEAD AND WORK LIGHT CIRCUIT (CLUSTER TYPE 1)
CASSETTE RADIO
REMOCON+ 12 43 10A
SPARE
REMOCON GND 13 31
44
FUSE BOX
NC 15
2
46
GND 16 47
1
2
CN-116 48
CN-12
52
7
1.2ROr
1.2ROr
0.8RW
0.8VW
WASHER SIG 5 53
6
0.8Br
PRE-HEAT 6 54
V
B
V
B
1.2ROr
0.8BrW
1.2Br
2
2
1
87
87
2
85
85
1
86
86
2
30
30
87a
87a
CL-4
CL-3
CL-6
57
CR-4
CL-5
NC 9
SWITCH PANEL
CR-13
POWER 24V 10 58
GND 11 59
HEAD LAMP
30 86
30 86
WORK LAMP
87a 87 85
87a 87 85
NC 12 60
HEAD LAMP RY
WORK LAMP RY
1409S4EC06
8. HEAD AND WORK LIGHT CIRCUIT (CLUSTER TYPE 2)
1) OPERATING FLOW
Fuse box (No.18) Head light relay [CR-13 (30,86)]
Fuse box (No.15) Work light relay [CR-4 (30,86)]
(1) Head light switch ON
Head light switch ON [CN-116 (1)] l/conn [CN-5 (49)] Head light relay [CR-13 (85) → (87)]
Head light ON [CL-3 (1)] , [CL-4 (1)]
l/conn [CN-11 (8)] AC & Heater controller illumination ON [4]
l/conn [CN-5 (13)] Cigar light [CL-2]
Radio & USB player illumination ON [CN-27 (9)]
2) CHECK POINT
Engine Start switch Check point Voltage
※ GND : Ground
4-22
NC
GND
IG 24V
2
1
CN-36
POWER IG
30A
BATTERY(+)
IG POWER
CN-279
1
ILLUMINATION
ILLUMINATION
REVERSE FAN
INCAR SENSOR
ROOM LAMP/CASSETTE 10A
0.8B
AC & HEATER
POWER TR BASE
W/TEMP SENSOR
DUCT SENSOR(+)
2
0.8ROr
AMBIENT SENSOR
CN-246
DUCT SENSOR(GND)
USB(D-) 1 3
0.5GY START KEY 30A
USB(D+) 2 4
CONTROLLER(AUTO)
0.5ROr AIR CON & HEATER 20A
3
9
8
7
6
5
4
3
2
1
USB(GND)
14
13
12
11
10
5
4 WIPER 10A
AUX S1
6
AUX S2 5 SPARE 10A
0.5V 7
USB+ 6 CLUSTER 10A
NC 7 8
CN-5
1.2B
MCU CONT. 20A
0.8ROr
NC 8 9
1 FUEL CUT-OFF SOL 10A
NC 9 10
2
2
5
5
4
1
4
1
8
7
6
9
8
7
6
3
3
10
12
11
10
AUX GND
3 11
CN-8
10A
CN-11
CN-27A CASSETTE
0.5V 4 12
1
0.8
0.8
USB 5V 1 START. STOP 30A
0.5LY 5 13
0.8ROr
USB D- 2 CONVERTER 20A
0.5BW 6 14
USB D+ 3 30A
0.5Lg 2RW WORK LAMP
4 7 15
USB GND
8 CABIN LAMP(OPT) 30A
NC 5 16
6 9 WIPER 10A
AUX L 17
AUX R 7 CL-2 10 1.2Br HEAD LAMP 20A
REMOTE ASSY
18
AUX GND 8 11 FUEL HEATER 30A
19
CN-27 12 SPARE 20A
ROr 0.8ROr 0.8ROr
ACC 1 13 20
10A
5
HORN
ILL- 2 14 21
CIGAR LIGHT
AC & HEATER 20A
NC 3 15 22
SAFETY SOL 10A
SPK FRT RH- 4 16 23
4-23
OPTION 20A
SPK FRT LH- 5 17 24
SOLENOIDE 20A
TEL MUTE 6 18 25
ANT 12V 7 19 CIGAR LIGHTER 20A
26
BACK UP+ 8 20 BEACON LAMP(OPT) 20A
0.8ROr 27
20A
HEAD AND WORK LIGHT CIRCUIT (CLUSTER TYPE 2)
CASSETTE RADIO
REMOCON+ 12 43 10A
SPARE
REMOCON GND 13 31
44
FUSE BOX
NC 15
2
46
GND 16 47
1
2
CN-116 48
CN-12
52
7
1.2ROr
1.2ROr
0.8RW
0.8VW
WASHER SIG 5 53
6
0.8Br
PRE-HEAT 6 54
V
B
V
B
1.2ROr
0.8BrW
1.2Br
2
2
1
87
87
2
85
85
1
86
86
2
30
30
87a
87a
CL-4
CL-3
CL-6
57
CR-4
CL-5
NC 9
SWITCH PANEL
CR-13
POWER 24V 10 58
GND 11 59
HEAD LAMP
30 86
30 86
WORK LAMP
87a 87 85
87a 87 85
NC 12 60
HEAD LAMP RY
WORK LAMP RY
1409S4EC56
9. BEACON LAMP AND CAB LIGHT CIRCUIT (CLUSTER TYPE 1)
1) OPERATING FLOW
Fuse box (No.27) I/conn [CN-5 (33)] Beacon lamp switch [CN-23 (8)]
Fuse box (No.16) Cab light relay [CR-9 (30, 86)]
(1) Beacon lamp switch ON
Beacon lamp switch ON [CS-23 (4)] Switch indicator lamp ON [CS-23 (11)]
l/conn [CN-10 (10)] Beacon lamp ON [CL-7]
(2) Cab light switch ON
Cab light switch ON [CN-116 (7)] I/conn [CN-5 (55)] Cabin lamp relay [CR-9 (85) → (87)]
I/conn [CN-5 (34, 38)] I/conn [CN-10 (11)] Cab light ON [CL-8 (2)]
I/conn [CN-10 (12)] Cab light ON [CL-9 (2)]
2) CHECK POINT
Engine Start switch Check point Voltage
4-24
12
M
3
4
9
12
10
CL-9
CL-7
CL-8
CN-36
1
1
2
2
IG POWER 30A
CAB LIGHT
1
7
8
2
11
BEACON LAMP
ROOM LAMP/CASSETTE 10A
2
1.2B
2.0V
1.2B
2.0V
10
11
5
9
12
4
8
1.2B
1
2
3
6
7
MCU 30A
1.2BrW
3
CS-23
4
BEACON LAMP SW
8
START KEY 30A
4
0.8B
AIR CON & HEATER 20A
1.2BrW
1.2Br
0.8BrW
5
WIPER 10A
6
CLUSTER 10A
3
7
2
CLUSTER 10A
8
MCU CONT. 20A
9
MCU EPPR 10A
10
5
4
1
9
8
7
6
3
10A
12
11
10
SWITCH PANEL
11
CN-10
CASSETTE 10A
12
FUEL CUT-OFF SOL 30A
1.2V
1.2V
1.2B
1.2B
13
1.2BrW
CONVERTER 20A
14
WORK LAMP 30A
15
2R CABIN LAMP(OPT) 30A
16
WIPER 10A
CN-5 17
HEAD LAMP 20A
1 18
FUEL HEATER 30A
2 19
START. STOP 20A
3 20
4 HORN 10A
21
5 AC & HEATER 20A
22
4-25
6 SAFETY SOL 10A
23
7 OPTION 20A
1.2B 1.2B 24
1
30 SOLENOIDE 20A
1.2B 1.2B
31 25
CIGAR LIGHTER 20A
32 26
1.2Br 1.2Br BEACON LAMP(OPT) 20A
33 27
1.2V 1.2V TRAVEL SOL 20A
34 28
PRE-HEAT 10A
35 29
FUEL P/PUMP 20A
36 30
37 SPARE 10A
CN-116
BEACON LAMP AND CAB LIGHT CIRCUIT (CLUSTER TYPE 1)
0.8V 0.8V 31
FUSE BOX
1 38
HEAD LIGHT OUT
2 39
WORK LIGHT OUT
INT. SIG 3 51
7
WIPER MOTOR DRIVE 4 52
WASHER SIG 5 53
PRE-HEAT 6 54
0.8Gr 0.8Gr 0.8Gr
CABIN LIGHT OUT 7 55
2R
TRAVEL ALARM 8 56
6
2V
0.8R
0.8Gr
NC 9 57
SWITCH PANEL
POWER 24V 10 58
GND 11 59
87
85
86
30
NC 12 60
87a
CR-9
30 86
87a 87 85
CABIN LAMP RY
1409S4EC07
10. BEACON LAMP AND CAB LIGHT CIRCUIT (CLUSTER TYPE 2)
1) OPERATING FLOW
Fuse box (No.27) I/conn [CN-5 (33)] Beacon lamp switch [CN-23 (8)]
Fuse box (No.16) Cab light relay [CR-9 (30, 86)]
(1) Beacon lamp switch ON
Beacon lamp switch ON [CS-23 (4)] Switch indicator lamp ON [CS-23 (11)]
l/conn [CN-10 (10)] Beacon lamp ON [CL-7]
(2) Cab light switch ON
Cab light switch ON [CN-116 (7)] I/conn [CN-5 (55)] Cabin lamp relay [CR-9 (85) → (87)]
I/conn [CN-5 (34, 38)] I/conn [CN-10 (11)] Cab light ON [CL-8 (2)]
I/conn [CN-10 (12)] Cab light ON [CL-9 (2)]
2) CHECK POINT
Engine Start switch Check point Voltage
4-26
12
M
3
4
9
12
10
CL-9
CL-7
CL-8
CN-36
1
1
2
2
IG POWER 30A
CAB LIGHT
1
7
8
2
11
BEACON LAMP
ROOM LAMP/CASSETTE 10A
2
1.2B
2.0V
1.2B
2.0V
10
11
5
9
12
4
8
1.2B
1
2
3
6
7
MCU 30A
1.2BrW
3
CS-23
4
BEACON LAMP SW
8
START KEY 30A
4
0.8B
AIR CON & HEATER 20A
1.2BrW
1.2Br
0.8BrW
5
WIPER 10A
6
SPARE 10A
3
7
2
CLUSTER 10A
8
MCU CONT. 20A
9
FUEL CUT-OFF SOL 10A
10
5
4
1
9
8
7
6
3
SWITCH PANEL 10A
12
11
10
11
CN-10
CASSETTE 10A
12
START. STOP 30A
1.2V
1.2V
1.2B
1.2B
13
1.2BrW
CONVERTER 20A
14
WORK LAMP 30A
15
2R CABIN LAMP(OPT) 30A
16
WIPER 10A
CN-5 17
HEAD LAMP 20A
1 18
FUEL HEATER 30A
2 19
SPARE 20A
3 20
4 HORN 10A
21
5 AC & HEATER 20A
22
4-27
6 SAFETY SOL 10A
23
7 OPTION 20A
1.2B 1.2B 24
1
30 SOLENOIDE 20A
1.2B 1.2B
31 25
CIGAR LIGHTER 20A
32 26
1.2Br 1.2Br 1.2Br BEACON LAMP(OPT) 20A
33 27
1.2V 1.2V TRAVEL SOL 20A
34 28
PRE-HEAT 10A
35 29
FUEL P/PUMP 20A
36 30
37 SPARE 10A
CN-116
BEACON LAMP AND CAB LIGHT CIRCUIT (CLUSTER TYPE 2)
0.8V 0.8V 31
FUSE BOX
1 38
HEAD LIGHT OUT
2 39
WORK LIGHT OUT
INT. SIG 3 51
7
WIPER MOTOR DRIVE 4 52
WASHER SIG 5 53
PRE-HEAT 6 54
0.8Gr 0.8Gr 0.8Gr
CABIN LIGHT OUT 7 55
2R
TRAVEL ALARM 8 56
6
2V
0.8R
0.8Gr
NC 9 57
SWITCH PANEL
POWER 24V 10 58
GND 11 59
87
85
86
30
NC 12 60
87a
CR-9
30 86
87a 87 85
CABIN LAMP RY
1409S4EC57
11. WIPER AND WASHER CIRCUIT (CLUSTER TYPE 1)
1) OPERATING FLOW
(1) Key switch ON
Fuse box (No.11) I/conn [CN-5 (57)] Switch panel [CN-116 (10)]
Fuse box (No.6) I/conn [CN-5 (18)] I/conn [CN-17 (5)] Wiper motor controller [CN-141(7)]
Wiper motor [CN-21(4)]
Fuse box (No.17) I/conn [CN-5 (24)] l/conn [CN-17 (4)] Wiper motor controller [CN-141 (6)]
Washer pump [CN-22 (2)]
(2) Wiper switch ON : 1st step (Intermittent)
Wiper switch ON [CN-116 (3)] I/conn [CN-17 (8)] Wiper motor controller [CN-141 (10) → (3)]
Wiper motor intermittently operating [CN-21 (6)]
(3) Wiper switch ON : 2nd step (continual)
Wiper switch ON [CN-116(4)] I/conn[CN-17(2)] Wiper motor controller [CN-141(2) → (4)]
Wiper motor operating [CN-21(2)]
(4) Washer switch ON
Washer switch ON [CN-116 (5)] I/conn [CN-17 (7)] Wiper motor controller [CN-141 (9) → (8)]
I/conn [CN-17 (6)] I/conn [CN-5 (19)] Washer pump [CN-22 (1)] Washer operating
Wiper switch ON [CN-116 (4)] I/conn[CN-17 (2)] Wiper motor controller [CN-141 (2) → (4)]
Wiper motor operating [CN-21 (2)]
(5) Auto parking
parking(when switch OFF)
Switch OFF [CN-116 (4)] Wiper motor parking position by wiper motor controller
2) CHECK POINT
4-28
CN-5
1
2
3
4 CN-36
5 IG POWER 30A
6
CN-21 6 1
CS-53 ROOM LAMP/CASSETTE 10A
3 1 7 2
R Or MCU 30A
2 8 3
Gr START KEY 30A
5 3 9 4
R 20A
4 10 AIR CON & HEATER
4 G B 5
5 0.8R WIPER 10A
WIPER CUT SW
11
L 6
6 M 2 6 12 CLUSTER 10A
WIPER MOTOR
7
13 CLUSTER 10A
8
1
14 MCU CONT. 20A
15 9
MCU EPPR 10A
16 10
4
0.8RW SWITCH PANEL 10A
17 11
0.8R 0.8R 10A
CN-141 18 CASSETTE
G 0.8V 0.8V 12
FEED BACK 1 19 FUEL CUT-OFF SOL 30A
W 13
1
MOTOR DRIVE SIG 2 CN-17 20 CONVERTER 20A
L 14
MOTOR DRIVE- 3 1 21 WORK LAMP 30A
R W 0.8W
MOTOR DRIVE+ 4 2 22 15
B B 1.2B CABIN LAMP(OPT) 30A
GND 5 3 23 16
GrW GrW 0.8ROr 0.8ROr 0.8GrW 0.8GrW WIPER 10A
VCC 6 4 24 17
R R 0.8R HEAD LAMP 20A
CONTINUE 24V 7 5 25 18
V V 0.8V 30A
WASHER P/P 8 6 26 FUEL HEATER
19
1
L L 0.8L
WASHER SIG. 9 7 27 START. STOP 20A
Br Br 0.8Br 20
INT. SIG 10 8 28 HORN 10A
Or 21
WIPER CUT SW 11 29 AC & HEATER 20A
1.2B 1.2B
12
22
N.C 30 10A
1.2B 1.2B SAFETY SOL
4-29
OPTION
32 24
SOLENOIDE 20A
5
33 25
CIGAR LIGHTER 20A
34 26
WIPER AND WASHER CIRCUIT (CLUSTER TYPE 1)
28
37 PRE-HEAT 10A
29
38
1
20A
2
FUEL P/PUMP
2
1
39 30
DO-5
SPARE 10A
CN-22
40 31
M
FUSE BOX
41
42
WASHER PUMP
43
44
45
46
CN-116 47
HEAD LIGHT OUT 1
48
WORK LIGHT OUT 2
0.8Br 49
INT. SIG 3 50
0.8W
WIPER MOTOR DRIVE 4 51
0.8L
WASHER SIG 5 52
PRE-HEAT 6 53
CABIN LIGHT OUT 7 54
3
TRAVEL ALARM 8 55
NC 9 56
SWITCH PANEL
0.8RW 0.8RW 0.8RW
POWER 24V 10 57
GND 11 58
NC 12 59
60
1409S4EC08
2
12. WIPER AND WASHER CIRCUIT (CLUSTER TYPE 2)
1) OPERATING FLOW
(1) Key switch ON
Fuse box (No.11) I/conn [CN-5 (57)] Switch panel [CN-116 (10)]
Fuse box (No.6) I/conn [CN-5 (18)] I/conn [CN-17 (5)] Wiper motor controller [CN-141(7)]
Wiper motor [CN-21(4)]
Fuse box (No.17) I/conn [CN-5 (24)] l/conn [CN-17 (4)] Wiper motor controller [CN-141 (6)]
Washer pump [CN-22 (2)]
(2) Wiper switch ON : 1st step (Intermittent)
Wiper switch ON [CN-116 (3)] I/conn [CN-17 (8)] Wiper motor controller [CN-141 (10) → (3)]
Wiper motor intermittently operating [CN-21 (6)]
(3) Wiper switch ON : 2nd step (continual)
Wiper switch ON [CN-116(4)] I/conn[CN-17(2)] Wiper motor controller [CN-141(2) → (4)]
Wiper motor operating [CN-21(2)]
(4) Washer switch ON
Washer switch ON [CN-116 (5)] I/conn [CN-17 (7)] Wiper motor controller [CN-141 (9) → (8)]
I/conn [CN-17 (6)] I/conn [CN-5 (19)] Washer pump [CN-22 (1)] Washer operating
Wiper switch ON [CN-116 (4)] I/conn[CN-17 (2)] Wiper motor controller [CN-141 (2) → (4)]
Wiper motor operating [CN-21 (2)]
(5) Auto parking
parking(when switch OFF)
Switch OFF [CN-116 (4)] Wiper motor parking position by wiper motor controller
2) CHECK POINT
Engine Start switch Check point Voltage
4-30
CN-5
1
2
3
4 CN-36
5 IG POWER 30A
6
CN-21 6 1
CS-53 ROOM LAMP/CASSETTE 10A
3 1 7 2
R Or MCU 30A
2 8 3
Gr START KEY 30A
5 3 9 4
R 20A
4 10 AIR CON & HEATER
4 G B 5
5 0.8R WIPER 10A
WIPER CUT SW
11
L 6
6 M 2 6 12 SPARE 10A
WIPER MOTOR
7
13 CLUSTER 10A
8
1
14 MCU CONT. 20A
15 9
FUEL CUT-OFF SOL 10A
16 10
4
0.8RW SWITCH PANEL 10A
17 11
0.8R 0.8R 10A
CN-141 18 CASSETTE
G 0.8V 0.8V 12
FEED BACK 1 19 START. STOP 30A
W 13
1
MOTOR DRIVE SIG 2 CN-17 20 CONVERTER 20A
L 14
MOTOR DRIVE- 3 1 21 WORK LAMP 30A
R W 0.8W
MOTOR DRIVE+ 4 2 22 15
B B 1.2B CABIN LAMP(OPT) 30A
GND 5 3 23 16
GrW GrW 0.8ROr 0.8ROr 0.8GrW 0.8GrW WIPER 10A
VCC 6 4 24 17
R R 0.8R HEAD LAMP 20A
CONTINUE 24V 7 5 25 18
V V 0.8V 30A
WASHER P/P 8 6 26 FUEL HEATER
19
1
L L 0.8L
WASHER SIG. 9 7 27 SPARE 20A
Br Br 0.8Br 20
INT. SIG 10 8 28 HORN 10A
Or 21
WIPER CUT SW 11 29 AC & HEATER 20A
1.2B 1.2B
12
22
N.C 30 10A
1.2B 1.2B SAFETY SOL
4-31
OPTION
32 24
SOLENOIDE 20A
5
33 25
CIGAR LIGHTER 20A
34 26
WIPER AND WASHER CIRCUIT (CLUSTER TYPE 2)
28
37 PRE-HEAT 10A
29
38
1
20A
2
FUEL P/PUMP
2
1
39 30
DO-5
SPARE 10A
CN-22
40 31
M
FUSE BOX
41
42
WASHER PUMP
43
44
45
46
CN-116 47
HEAD LIGHT OUT 1
48
WORK LIGHT OUT 2
0.8Br 49
INT. SIG 3 50
0.8W
WIPER MOTOR DRIVE 4 51
0.8L
WASHER SIG 5 52
PRE-HEAT 6 53
CABIN LIGHT OUT 7 54
3
TRAVEL ALARM 8 55
NC 9 56
SWITCH PANEL
0.8RW 0.8RW 0.8RW
POWER 24V 10 57
GND 11 58
NC 12 59
60
1409S4EC58
2
CN-76
G
M- 6
6 5 V Service Tool
M M+ 5
NC 4
2 B CN-138
GND
P- 3
IG 24V
3 1 W 12V C
CAN_Hi
12V
CAN_Lo
2 1.2V
CAN2_Hi
SIG
CAN2_Lo
0.8Gr 24V A
RS232_TX
RS232_RX
P+ 1
-
+
S
24V GND B
ACCEL ACTUATOR
DC & DC
RS232 P_DUMP
CN-51
B
A
C
CONVERTER
1.2R
ACCEL DIAL
BATT.POWER_24V 1
CN-142
1.2RW
POWER IG 2
A
C
E
B
D
H
G
0.8B
0.8W
POWER_24V OUT 3
0.8Gr
TACHO SENSOR+ 4
0.8B
0.8B
0.8V
0.8R
0.8G
0.8G
0.8G
0.8G
0.8G
5
4
1
9
8
7
6
3
GND_5V 5
16
15
14
13
12
11
10
0.8BW
0.8Gr
CN-7
POWER_5V OUT 6
0.8V
1
2
3
4
5
6
7
8
9
10
G/A MOTOR(+) 7
RH CONSOLE
0.8G
0.8B
0.8W
0.8Gr
CN-126
G/A MOTOR(-) 8
NC 9
NC 10
1.2B
GND_MAIN 11
CN-36
CAN_SHIELD 12
IG POWER 30A
GND_RETURN 13 1
SPEED SENSOR+(HMC) 14 ROOM LAMP/CASSETTE 10A
2
TACHO SENSOR- 15 1.2R MCU 30A
0.8BW 3
PROGRAM DUMP 16 START KEY 30A
4
ONE TOUCH DECEL 17 AIR CON & HEATER 20A
POWER BOOS SW 18 5
WIPER 10A
HOUR METER 6
0.8BW
19
CLUSTER 10A
ANTI RESTARY RY.(F) 20 7
0.8V CLUSTER 10A
CAN1 Hi 21 8
2
1
60
59
52
51
50
45
44
43
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1.2RW MCU CONT. 20A
NC 22
CN-5
9
RS485+(TX)-CLUSTER 23 1.2R MCU_EPPR 20A
0.8R 10
RS232C1_TX-HRDT 24 SWITCH PANEL 10A
11
RS232C2_TX-RCM 25 CASSETTE 10A
12
CONTROLLER CIRCUIT (CLUSTER TYPE 1)
4-32
WORK LAMP 30A
AIR CLEANER SW(NO) 29 15
CABIN LAMP(OPT) 30A
BLOWER SIG. 30 16
0.8G
CAN1 Lo WIPER 10A
31 17
NC 32 HEAD LAMP 20A
18
RS485-(RX)-CLUSTER 33 FUEL HEATER 30A
0.8G 19
RS232C1_RX-HRDT 34 START,STOP 30A
35 20
HORN 10A
NC 39 21
AC& HEATER 20A
NC 40 22
SAFETY SOL 10A
CN-52 23
20A
MCU
OPTION
ARM REGEN SOL 1 24
SOLENOIDE 20A
POWER MAX SOL 2 25
CIGAR LIGHTER 20A
0.8 26
POWER IG EPPR 8 BEACON LAMP(OPT) 20A
0.8 27
PUMP POWER EPPR+ 9 TRAVEL SOL 20A
28
ATT.EPPR+ 10 PRE-HEAT 10A
29
ENG STOP RY(H) FUEL P/PUMP 20A
0.8 30
ENG PRE-HEAT RY 15 10A
Br
SPARE
Or
NC 16
31
FUSE BOX
5
4
1
9
8
7
6
3
EPPR GND 18
15
14
13
12
11
10
0.8
CN-2
NC 21
0.8BOr
NC 22
0.8W
ACCEL DIAL SIG. 23
HYD.TEMP SENDER 24
4
2
3
5
1
ALT. LEVEL 27
1409S4EC09
0.8W
3 2
4 5 1
CN-75
GOV.POTENTIO SIG. 28
PRE-HEAT RY
EPPR VALVE
OVERLOAD SENSOR 39
NC 40
CN-76
G
M- 6
6 5 V
M M+ 5
NC 4
2 B CN-138
P- 3
GND
3 1 W 12V C
12V
IG 24V
SIG 2 1.2V
CAN_Hi
CAN_Lo
0.8Gr
CAN2_Hi
24V A
CAN2_Lo
RS232_TX
P+ 1
RS232_RX
-
+
S
24V GND B
DC & DC
ACCEL ACTUATOR
Service Tool
CN-51
RS232 P_DUMP
CONVERTER
B
A
ACCEL DIAL
WORKING PS 1
CN-142
POWER MAX SW 2
A
C
E
B
D
H
G
0.8B
0.8W
TRAVEL ALARM SW 3
0.8Gr
ENG OIL PS 4
0.8B
0.8V
5
4
1
0.8R
9
8
7
6
3
0.8G
0.8G
0.8G
0.8G
0.8G
NC
16
15
14
13
12
11
10
5
0.8BW
CN-7
NC 6
1
2
3
4
5
6
7
8
9
10
24V(PRES.SENSOR) 7
RH CONSOLE
0.8B
0.8W
0.8Gr
CN-126
GND(PRES.SENSOR) 8
ALT LEVEL 9
P1 PRESS SIG. 10
11
B CN-36
GND (POT&DIAL) 20
G/OR IG POWER 30A
5V (POT&DIAL) 21 1
W ROOM LAMP/CASSETTE 10A
POT-SIG 22 2
W 30A
ACCEL DIAL SIG 23 1.2R MCU
3
FUEL LEVEL SENSOR 24 START KEY 30A
4
TACHO SENSOR(-) 25 AIR CON/HEATER 20A
TACHO SENSOR(+) 5
26 WIPER 10A
6
0.8BW
27 10A
SPARE
WATER TEMP SENDOR 33 7
CLUSTER 10A
HYD TEMP SENDOR 34 8
2
1
60
59
52
51
50
45
44
43
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1.2RW MCU CONT. 20A
NC
CN-5
35 9
NC 36 FUEL CUT-OFF SOL 10A
10
SWITCH PANEL 10A
11
CN-50 10A
MONITORING CIRCUIT (CLUSTER TYPE 2)
CASSETTE
12
BOOM PRIORITY SOL 1 START. STOP 30A
MAX FLOW SOL. 2 13
MCU
1.2V CONVERTER 20A
14
4-33
POWER MAX SOL. 3
WORK LAMP 30A
HOUR-METER 4 15
Y/W CABIN LAMP(OPT) 30A
ENG PREHEATER 5 16
WIPER 10A
FUEL HEATER 6 17
GY 20A
BATTERY 24V(+) 7 HEAD LAMP
BR 18
PUMP EPPR(-) 8 FUEL HEATER 30A
19
NC 9 SPARE 20A
B/W 20
PROGRAM DUMP 10 HORN 10A
ANTI-RESTART RY 11 21
V AC& HEATER 20A
ACCEL ACT(+) 12 22
SAFETY SOL 10A
TRAVEL SPEED SOL. 13 23
OPTION 20A
NC 14 24
NC SOLENOIDE 20A
15 25
TRAVEL BUZZER 16 CIGAR 20A
26
PRE-HEAT SW 17 BEACON LAMP(OPT) 20A
27
NC 18 TRAVEL SOL 20A
NC 28
19 PRE-HEAT 10A
OVERLOAD SIG 20 29
FUEL P/P 20A
NC 21 30
10A
Br
Or SPARE
NC 22 31
G
FUSE BOX
ACCEL ACT(-) 23
OR
POWER IG 24
2
5
4
1
9
8
7
6
3
15
14
13
12
11
10
CN-2
NC 25
NC 26
NC 27
1.2Br
1.2Or
GND (MAIN) 28
0.8BOr
SERIAL-TX 29
SERIAL-RX 30
4
2
3
5
1
1.2Br
1.2Or
GND 31
R
CR-36
RS232 (+) 32
G
1
2
RS232 (-) 33
B
3 2
4 5 1
RS232 (GND) 34
CN-75
1409S4EC59
NC 35
PRE-HEAT RY
OR
PUMP EPPR(+)
EPPR VALVE
36
CN-51
BATT.POWER_24V 1
Pa
CD-10
POWER IG 2
C 1
2
2
1
POWER_24V OUT 3
CD-1
HYD TEMP
CD-2
TACHO SENSOR+ 4
FUEL SENDOR
0.8
1.2B
AIR CLEANER SW
0.8B
0.8
1.2YOr
GND_5V
0.8B
5
POWER_5V OUT 6
G/A MOTOR(+) 7
G/A MOTOR(-) 8
NC 9
NC 10
GND_MAIN 11
SH
0.8L
0.8B
0.8Y
0.8Gr
CAN_SHIELD 12 B
GND_RETURN 13
8
7
6
5
4
3
2
1
5
4
1
9
8
7
6
3
60
59
58
57
53
52
51
38
37
36
35
24
23
22
21
CN-5
SPEED SENSOR+(HMC)
CN-56
14
TACHO SENSOR- 15
RR
RR
RR
RR
RR
RR
RR
RR
SH
0.8L
0.8Y
0.8B
CN-36
0.8Gr
PROGRAM DUMP 16
0.8RW
ONE TOUCH DECEL 17 IG POWER 30A
1
TX
RX
POWER BOOS SW 18 ROOM LAMP/CASSETTE 10A
SIG_2
GND
SIG_3
IG 24V
2
BATT.24V
HOUR METER 19 MCU 30A
CLUSTER
CAMERA SIG
ANTI RESTARY RY.(F) 20 3
START KEY 30A
CAN1 Hi 21 4
AIR CON & HEATER 20A
NC 22 5
0.8L WIPER 10A
RS485+(TX)-CLUSTER 23 6
0.8RW CLUSTER 10A
RS232C1_TX-HRDT 24 7
RS232C2_TX-RCM 25 0.8GR CLUSTER 10A
8
TR ALARM SELECT SIG 26 MCU CONT. 20A
9
ENG OIL PS 27 MCU EPPR 10A
COOLENT LEVEL 10
28 B SWITCH PANEL 10A
AIR CLEANER SW(NO) 11
CONTROLLER CIRCUIT (CLUSTER TYPE 1)
29 10A
CASSETTE
BLOWER SIG. 30 12
FUEL CUT-OFF SOL 30A
CAN1 Lo
4-34
31 13
CONVERTER 20A
NC 32 14
0.8Y
RS485-(RX)-CLUSTER WORK LAMP 30A
33 15
RS232C1_RX-HRDT 34 CABIN LAMP(OPT) 30A
16
RS232C2_RX-RCM 35 WIPER 10A
17
HEAD LAMP 20A
18
FUEL HEATER 30A
MCU
CN-52 19
ARM REGEN SOL START. STOP 20A
1 20
POWER MAX SOL 2 HORN 10A
21
TRAVEL SPEED SOL 3 AC & HEATER 20A
22
ATT_ SAFETY SOL 4 SAFETY SOL 10A
ATT_PRESS SOL. 5 23
OPTION 20A
6 24
SOLENOIDE 20A
ACCEL DIAL SIG. 23 25
B CIGAR LIGHTER 20A
HYD.TEMP SENDER 24 26
BEACON LAMP(OPT) 20A
WATER TEMP SENDER 25 27
B
FUEL LEVEL SENSOR 26 TRAVEL SOL 20A
28
ALT. LEVEL 27 PRE-HEAT 10A
29
GOV.POTENTIO SIG. 28 FUEL P/PUMP 20A
30
P1 PRESS SENSOR 29 SPARE 10A
P2 PRESS SENSOR 30 31
FUSE BOX
NC 31
PUMP EPPR2 SENSOR 32
ATT PILOT PRESSURE 33
ARM IN_OUT BK IN PS 34
BOOM UP PS SENSOR 35
SWING PS SENSOR 36
WORK PS SENSOR(A) 37
1409S4EC10
TRAVEL PS SENSOR(A) 38
OVERLOAD SENSOR 39
NC 40
CN-51
WORKING PS 1
Pa
CD-10
POWER MAX SW 2
C 1
2
2
1
TRAVEL ALARM SW 3
CD-1
HYD TEMP
CD-2
ENG OIL PS 4
FUEL SENDOR
0.8
1.2B
AIR CLEANER SW
0.8B
0.8
1.2YOr
0.8B
NC 5
NC 6
24V(PRES.SENSOR) 7
GND(PRES.SENSOR) 8
ALT LEVEL 9
P1 PRESS SIG. 10
L
Y
B
Br
P2 PRESS SIG.
SH
11
0.8L
0.8B
0.8Y
0.8Gr
P3 PRESS SIG. 12
TRAVEL PS 13
4
3
2
1
5
4
1
9
8
7
6
3
60
59
58
57
53
52
51
38
37
36
35
24
23
22
21
CN-5
O/T DECEL SW 14
CN-56A
WATER LEVEL SW CN-36
15
RR
B
SH
0.8L
0.8Y
0.8B
IG POWER 30A
0.8Gr
AIR CLEANER SW 16 1
NC 17 ROOM LAMP/CASSETTE 10A
2
NC 18 MCU 30A
3
TX
RX
NC 19
GND
START KEY 30A
GND (POT&DIAL) 20 4
20A
POWER IG(24V)
AIR CON/HEATER
CLUSTER
5V (POT&DIAL) 21 5
WIPER 10A
POT-SIG 22 6
SPARE 10A
ACCEL DIAL SIG 23 7
B/OR 0.8GR CLUSTER 10A
FUEL LEVEL SENSOR 24 8
TACHO SENSOR(-) 25 MCU CONT. 20A
9
TACHO SENSOR(+) 26 FUEL CUT-OFF SOL 10A
10
NC 27 SWITCH PANEL 10A
NC 11
28 CASSETTE 10A
MONITORING CIRCUIT (CLUSTER TYPE 2)
NC 29 12
START. STOP 30A
NC 30 13
B CONVERTER 20A
GND (SENSOR) 31 14
4-35
WORK LAMP 30A
PUMP PROLIX SW 32 15
WATER TEMP SENDOR CABIN LAMP(OPT) 30A
33 16
BR/OR
HYD TEMP SENDOR 34 WIPER 10A
17
NC 35 HEAD LAMP 20A
18
NC 36 FUEL HEATER 30A
19
CN-50 SPARE 20A
20
BOOM PRIORITY SOL 1 HORN 10A
21
MAX FLOW SOL. 2 AC& HEATER 20A
22
POWER MAX SOL. 3 SAFETY SOL 10A
HOUR-METER 4 23
OPTION 20A
ENG PREHEATER 5 24
SOLENOIDE 20A
FUEL HEATER 6 25
CIGAR 20A
BATTERY 24V(+) 7 26
BEACON LAMP(OPT) 20A
PUMP EPPR(-) 8 27
NC 9 TRAVEL SOL 20A
28
PROGRAM DUMP 10 PRE-HEAT 10A
29
ANTI-RESTART RY 11 FUEL P/P 20A
ACCEL ACT(+) 30
12 SPARE 10A
TRAVEL SPEED SOL. 13 31
FUSE BOX
NC 14
15
GND (MAIN) 28
Y
SERIAL-TX 29
L
SERIAL-RX 30
GND 31
RS232 (+) 32
RS232 (-) 33
RS232 (GND) 34
1409S4EC60
NC 35
PUMP EPPR(+) 36
GROUP 3 ELECTRICAL COMPONENT SPECIFICATION
Rated load :
24V ※ Check coil resistance(M4 to M4)
100A (continuity) Normal : About 50Ω
Battery relay
1000A ※ Check contact
(30seconds) Normal : ∞Ω
CR-1
※ Check contact
Glow plug relay 24V 200A Normal : 0.942Ω
(For terminal 1-GND)
CR-24
5
4
1
6
2
3
Start key
B-ST : 24V
40A ON : 0Ω(for terminal 1-3 and 1-2)
H0 I
4
3
STC BR ACC H
CS-2
A SUPPLY
B SIG
C RETURN ※ Check contact
Pressure sensor 8~30V
Normal : 0.1Ω
CD-6 CD-7 CD-42
CD-43 CD-44
CLUSTER TYPE 1
(CD-24, CD-31, CD-32, CD-69)
2 ※ Check resistance
m
rp
4-38
Part name Symbol Specifications Check
※ Check resistance
Glow plug 24V 200A
0.25~0.12Ω
CN-80
※ Check contact
Air cleaner Pa High level : ∞Ω
(N.O TYPE)
pressure switch Low level : 0Ω
CD-10
※ Check resistance
Full : 50Ω 6/12 : 350Ω
2 11/12 : 100Ω 5/12 : 400Ω
10/12 : 150Ω 4/12 : 450Ω
Fuel sender 1 -
9/12 : 200Ω 3/12 : 500Ω
8/12 : 250Ω 2/12 : 550Ω
CD-2 7/12 : 300Ω 1/12 : 600Ω
Empty warning : 700Ω
3 4 4
3 ※ Check resistance
2
Relay
1 2 1
Normal : About 200Ω
CR-46
24V 20A (for terminal 1-3)
(air con blower)
0Ω
(for terminal 2-4)
1
4 5 1 ※ Check resistance
2
3 Normal : About 160 Ω
Relay 4 24V 16A (for terminal 1-2)
5 3 2
0Ω(for terminal 3-4)
CR-2 CR-36 CR-62 ∞Ω(for terminal 3-5)
CLUSTER TYPE 1 (CR-51)
4-39
Part name Symbol Specifications Check
30
86
87a 87 85 ※ Check resistance
87 Normal : About 160 Ω
Relay 85 24V 16A (for terminal 85-86)
87a 30 86
0Ω(for terminal 30-87a)
CR-4 CR-5 CR-7 CR-9 ∞Ω(for terminal 30-87)
CR-13 CR-35 CR-46
2 ※ Check resistance
Solenoid valve Normal : 15~25Ω
24V 1A
CN-68 CN-70 CN-88
CN-135 CN-140 (for terminal 1-2)
CLUSTER TYPE 1 (CN-66, CN-149,
CN-236, CN-237)
1
※ Check resistance
EPPR valve
2 700mA Normal : 15~25Ω
(for terminal 1-2)
CN-75 CN-133 CN-242
1
※ Check resistance
Speaker 2 20W
Normal : A fewΩ
CN-23(LH)
CN-24(RH)
※ Check contact
7
6
3
2
1
8
4
12
5
11
10
Normal
11
2
8
12
12
9
4
※ Check resist
Normal : About 5kΩ
A (for terminal A-C)
+
Accel dial ※ Check voltage
B S -
Normal : About 5V
C - (for terminal A-C)
CN-142 : 2~4.5V
(for terminal C-B)
4-40
Part name Symbol Specifications Check
3 ※ Check disconnection
Normal : 1.0Ω
Room lamp 2 ON : 0Ω(For terminal 1-2)
24V 10W
1 ∞Ω(For terminal 1-3)
OFF : ∞Ω(For terminal 1-2)
CL-1 0Ω(For terminal 1-3)
2
Head lamp, ※ Check disconnection
24V 65W
Work lamp, 1
(H3 Type) Normal : 1.2Ω
Cab lamp
CL-3 CL-5
CL-4 CL-4 CL-6
CL-5
CL-8
CL-6 CL-9
CL-8 CL-9
CL-7
-
CL-7
1 M
24V 10A ※Check resistance
Fuel filler pump 2 35ℓ /min Normal : 1.0Ω
CN-61
3 ※Check operation
Service meter 2
h Supply power(24V) to terminal
16~32V
1 No.2 and connect terminal No.1
and ground
CN-48
1 ※Check operation
DC22~28V
Horn 2 Supply power(24V) to each
2A
terminal and connect ground.
CN-20 CN-25
4-41
Part name Symbol Specifications Check
2 3 ※Check contact
1
Normal : 0Ω(for terminal 1-2)
2 24V 15A
Safety switch ∞Ω(for terminal 1-3)
(N.C TYPE)
3 Operating : ∞Ω(for terminal 1-2)
1
0Ω(for terminal 1-3)
CS-4
CS-4
2
Pa 24V 2.5A ※Check contact
Receiver dryer 1 Normal : ∞Ω
CN-29
10
11
12
13
14
15
16
1
2
3
4
5
6
7
9
8
※Check voltage
REMOCON GND
SPK FRT RH+
Radio &
REMOCON+
BACK UP+
TEL MUTE
24V 2A 20~25V
ANT 12V
CD/MP3 plalyer
GND
ACC
ILL+
NC
NC
CN-27
※Check contact
Washer pump 24V 3.8A
Normal : 10.7Ω(for terminal 1-2)
CN-22
3 1
2
5 3
4 ※Check disconnection
Wiper motor 4
5
24V 2A
Normal : 7Ω(for terminal 2-6)
6 M 2 6
CN-21
4-42
Part name Symbol Specifications Check
3 12V 12V
DC/DC 2 24V 24V (1-2)
1 24V 12V 3A
Converter GND 12V (1-3)
CN-138
B+
G
1 P
2 L
3~ ※Check contact
Alternator 3 FI
U 24V 50A Normal : 0Ω (for terminal B+-I)
4 NC
Normal : 24~27.5V
CN-74
M
M
Denso ※Check contact
Starter
24V 4.5kW Normal : 0.1Ω
B+
CN-45
※Check contact
Travel alarm 24V 0.5A
Normal : 5.2Ω
CN-81
1
Aircon ※Check contact
24V 79W
compressor Normal : 13.4Ω
CN-28
4-43
Part name Symbol Specifications Check
※Check contact
Start relay 24V 300A
Normal : 0.94Ω(for terminal 1-2)
CR-23
1 M ※Check resistance
Blower motor 24V 9.5A
2 Normal : 2.5Ω(for terminal 1-2)
※Check resistance
Duct sensor 2 1˚C OFF Normal : 0Ω(for terminal 1-2),
(switch) 1 4˚C ON the atmosphere temp :
Over 4˚C
※Check resistance
Door switch 24V 2W
Normal : About 5MΩ
CS-1
CS-1
Switch 1
(power max, one ※Check resistance
2 24V 6A
touch decal, Normal : ∞Ω
horn, breaker) CS-5 CS-19
CS-26 CS-26A CS-29
※Check disconnection
2
Fusible link normal : 0Ω
60A
(cluster type 2) (connect ring terminal and check
1
resist between terminal 1 and 2)
CN-60 CN-95
4-44
Part name Symbol Specifications Check
2 ※Check disconnection
Fusible link
Normal : 0.1Ω
(cluster type 1) 1 60A
(connect ring terminal and check
CN-60 CN-95 resist between terminal 1 and 2)
※Check disconnection
Master switch 6-36V
Normal : 0.1Ω
CS-74
Pressure switch
Pa 0.5kgf/cm2 ※Check resistance
(for engine oil)
(N.C TYPE) Normal : 0Ω(CLOSE)
CD-18
M- 6
6 5
M M+ 5 ※ Check resistance
NC 4
2 Normal : 1-2 Ω (for terminal 5-6)
Accel actuator 3 1
P- 3 -
SIG 2 0.8-1.2kΩ
P+ 1 (for terminal 1-3)
CN-76
G
Fuel cut-off
F ※ Check resistance
(cluster type 1) 24V
Normal : 15-25 Ω
H
CN-79
4-45
GROUP 4 CONNECTORS
1. CONNECTOR DESTINATION
Connector No. of Connector part No.
Type Destination
number pin Female Male
CN-1 AMP 6 I/conn (Frame harness-Pump PS harness) S816-006002 S816-106002
CN-2 AMP 15 I/conn (Frame harness-Engine harness) 2-85262-1 368301-1
CN-3 AMP 12 I/conn (Frame harness-Engine harness) S816-012002 S816-112002
CN-4 AMP 16 I/conn (Console harness LH-Frame harness) 368047-1 368050-1
CN-5 DEUTSCH 60 I/conn (Side harness RH-Frame harness) DRB16-60SAE-L018 DRB14-60PAE-L018
CN-7 AMP 16 I/conn (Console harness RH-Frame harness) 368047-1 368050-1
CN-8 AMP 12 I/conn (Console harness RH-Frame harness) S816-012002 S816-112002
CN-10 DEUTSCH 12 I/conn (Cab harness-Side harness RH) DT06-12S-EP06 DT04-12P-BE02
CN-11 DEUTSCH 8 I/conn (Frame harness-Aircon harness) DT06-8S-EP06 -
CN-12 DEUTSCH 2 I/conn (Frame harness-Boom wire harness) DT06-2S-EP06 DT04-2P-E005
CN-15 AMP 12 I/conn (Frame harness) S816-012002 S816-112002
CN-17 AMP 8 I/conn (Wiper harness) S816-008002 S816-108002
CN-20 MOLEX 2 Horn 36825-0211 -
CN-21 AMP 6 Wiper motor 925276-0 -
CN-22 KET 2 Washer pump MG640605 -
CN-23 KET 2 Speaker-LH MG610070 -
CN-24 KET 2 Speaker-RH MG610070 -
CN-25 MOLEX 2 Horn 36825-0211 -
CN-27 KUM 16 Cassette radio PK145-16017 -
CN-27A AMP 8 USB Player S816-008002 S816-108002
CN-28 KUM 1 Aircon compressor MWP-01F-B -
CN-29 KET 2 Receiver dryer MG640795 -
CN-36 - - Fuse & relay box 21Q7-10910 -
CN-45 RING-TERM - Starter motor B+ S820-308000 DT04-4P-E005
CN-48 KET 1 Service meter 2-520193-2 -
CN-50 AMP 36 MCU (cluster type 2) 3441111-1 -
CN-51 DEUTSCH 40 MCU (cluster type 1) DRC26-40SA -
CN-51A AMP 36 MCU (cluster type 2) 3441111-1 -
CN-52 DEUTSCH 40 MCU (cluster type 1) DRC26-40SB -
CN-56 AMP 8 Cluster (type 1) - S816-108002
CN-56A DEUTSCH 4 Cluster (type 2) - DT04-4P-E004
CN-60 AMP 2 Fusible link 21N4-01320 S813-130201
CN-61 DEUTSCH 2 Fuel filler pump DT06-2S-EP06 -
CN-66 DEUTSCH 2 Breaker solenoid DT06-2S-EP06 DT04-2P-EP005
CN-68 DEUTSCH 2 Safety solenoid DT06-2S-EP06 -
CN-70 DEUTSCH 2 Travel high solenoid DT06-2S-EP06 -
4-46
Connector No. of Connector part No.
Type Destination
number pin Female Male
CN-74 AMP 4 Alternator "L" terminal 12186568 -
CN-75 AMP 2 Pump EPPR S816-002002 -
CN-76 DEUTSCH 6 Accel actuator DT06-6S-EP06 -
CN-79 RING-TERM 3 Fuel cut off solenoid (cluster type 1) ST710289-2 -
CN-80 RING-TERM - Glow plug S820-306000 -
CN-81 DEUTSCH 2 Travel buzzer solenoid DT06-2S-EP06 -
CN-88 DEUTSCH 2 Power max solenoid DT06-2S-EP06 -
CN-95 YAZAKI 2 Fusible link 21N4-01311 7122-4125-50
CN-96 AMP 4 Fuel warmer 2-967325-3 -
CN-113 KET 2 Travel buzzer MG651205-5 -
CN-116 AMP 12 Switch panel 176116 -
CN-126 AMP 9 Service tool S816-009002 S816-109002
CN-133 DEUTSCH 2 Boom priority solenoid DT06-2S-EP06 -
CN-135 DEUTSCH 2 Arm regeneration solenoid DT06-2S-EP06 -
CN-138 DEUTSCH 3 DC/DC Converter DT06-3S -
CN-139 AMP 2 12V socket 172434-2 -
CN-140 DEUTSCH 2 Quick clamp solenoid DT06-2S-EP06 DT04-2P-E005
CN-141 AMP 13 Wiper motor controller 172498-1 DT04-3P-EP10
CN-142 DEUTSCH 3 Accel dial DT06-3S-EP06 -
CN-149 DEUTSCH 2 Attach safety solenoid DT06-2S-EP06 -
CN-156 DEUTSCH 2 Air seat - DT04-2P-E005
CN-170 AMP 2 Heated seat 12052641 -
CN-236 DEUTSCH 2 Attach pressure solenoid DT06-2S-EP06 -
CN-237 DEUTSCH 2 Attach conflux solenoid DT06-2S-EP06 -
CN-242 DEUTSCH 2 Attach flow solenoid DT06-2S-EP06 DT04-2P-E005
CN-246 AMP 10 USB & Socket assy 316988-6 -
CN-247 DEUTSCH 8 PWM convert DT06-08SA-EP06 DT04-8P
CN-249 DEUTSCH 4 Rear view camera DT06-4S-EP06 DT04-4P-E005
CN-279 AMP 2 Accel dial LED S816-002002 -
·Relay
CR-1 RING-TERM - Battery relay ST730135-2 -
CR-2 - 5 Horn relay - -
CR-4 - 5 Work lamp relay - -
CR-5 - 5 Anti restart relay - -
CR-7 - 5 Aircon compressor relay - -
CR-9 - 5 Cabin lamp relay - -
CR-13 - 5 Head lamp relay - -
CR-23 AMP 2 Start relay - S814-102001
4-47
Connector No. of Connector part No.
Type Destination
number pin Female Male
CR-24 AMP 1 Preheat relay S822-014000 -
CR-35 - 5 Power relay - -
CR-36 - 5 Preheat relay - -
CR-46 - 5 Fuel warmer relay - -
CR-51 - 5 Fuel cut off relay (cluster type 1) - -
CR-62 - 5 Breaker relay - -
·Switch
CS-1 SHUR 1 Door switch S822-014002 S822-114002
CS-2 WP 6 Start key switch S816-006100 -
CS-4 DEUTSCH 3 Safety switch DT06-3S-EP06 -
CS-5 DEUTSCH 2 Horn switch - DT04-2P-E005
CS-19 DEUTSCH 2 One touch decel switch - DT04-2P-E005
CS-20 AMP 1 Safety switch S822-014002 -
CS-23 SWF 12 Beacon lamp switch SWF589790 -
CS-26 DEUTSCH 2 Breaker switch DT06-2S-EP06 -
CS-26A AMP 2 Breaker pedal switch S816-002002 S816-102002
CS-27 SWF 10 Breaker switch SWF 593757 -
CS-29 DEUTSCH 2 Power max switch DT06-2S-EP06 -
CS-33 AMP 6 Emergency engine stop switch S816-006002 S816-106002
CS-50 SWF 12 Overload switch SWF589790 -
CS-53 AMP 1 Wiper cut switch S822-014002 -
CS-67 SWF 12 Quick clamp switch SWF 589790 -
CS-74A AMP 2 Master switch S813-030201 -
CS-74B DEUTSCH 2 Master switch DT06-2S-EP06 -
CS-82 SWF 12 Heated seat switch SWF 589790 -
CS-83 SWF 12 Spare switch SWF589790 -
CS-99 SWF 12 Spare switch SWF 589790 -
CS-100 SWF 12 Spare switch SWF 589790 -
·Light
CL-1 KET 3 Room lamp MG651032 -
CL-2 AMP 1 Cigar light S822-014002 S822-114002
CL-3 DEUTSCH 2 Head lamp-LH DT06-2S-EP06 DT04-2P-E005
CL-4 DEUTSCH 2 Head lamp-RH DT06-2S-EP06 DT04-2P-E005
CL-5 AMP 2 Work lamp-LH 180923-0 -
CL-6 AMP 2 Work lamp-RH 180923-0 -
CL-7 SHUR 1 Beacon lamp S822-014002 S822-114002
CL-8 DEUTSCH 2 Cab light-LH DT06-2S-EP06 DT-2P
CL-9 DEUTSCH 2 Cab light-RH DT06-2S-EP06 DT04-2P
4-48
Connector No. of Connector part No.
Type Destination
number pin Female Male
·Sensor, sendor
CD-1 AMP 2 Hydraulic oil temp sender 85202-1 -
CD-2 DEUTSCH 2 Fuel level sender DT06-2S-EP06 -
CD-6 DEUTSCH 3 Travel pressure sensor DT06-3S-EP06 -
CD-7 DEUTSCH 3 Working pressure sensor DT06-3S-EP06 -
CD-8 AMP 2 Water temperature sender 85202-1 -
CD-10 RING TERM - Air cleaner switch ST730135-2 -
CD-17 - 2 Speed sensor - S818-120221
CD-18 RING TERM 1 Engine oil pressure switch S820-104000 -
CD-24 DEUTSCH 3 Swing sensor (cluster type 1) DT06-3S-EP06 -
CD-31 DEUTSCH 3 Overload sensor (cluster type 1) S816-003002 S816-103002
CD-32 DEUTSCH 3 Boom up sensor (cluster type 1) DT06-3S-EP06 -
CD-42 DEUTSCH 3 Pump pressure 1 DT06-3S-EP06 -
CD-43 DEUTSCH 3 Pump pressure 2 DT06-3S-EP06 -
CD-44 DEUTSCH 3 Pump pressure 3 DT06-3S-EP06 -
CD-69 DEUTSCH 3 Attach pressure sensor (cluster type 1) DT06-3S-EP06 -
4-49
2. CONNECTION TABLE FOR CONNECTORS
1) PA TYPE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
2 5 1 3
1 3 2 5
S811-005002 S811-105002
3 7 1 4
1 4 3 7
S811-007002 S811-107002
4 9 1 5
1 5 4 9
S811-009002 3S811-109002
5 11 1 6
11
1 6 5 11
S811-011002 S811-111002
4 - 50
No. of
Receptacle connector (female) Plug connector (male)
pin
6 13 1 7
13
1 7 6 13
S811-013002 S811-113002
8 1 9
17
17
1 9 8 17
S811-017002 S811-117002
1 21
1 11
21
1 11 1 21
S811-021002 S811-121002
4 - 51
2) J TYPE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1 1
2
2 12
S816-002001 S816-102001
2 3 1
3 1 2
S816-003001 S816-103001
3 1 4 2
4 2 3 1
S816-004001 S816-104001
8 5 2
6 3 1
8 5 2 6 3 1
S816-008001 S816-108001
4 - 52
3) SWP TYPE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1 1
S814-001000 S814-101000
2 1
1 2
S814-002000 S814-102000
3 1
2 1 23
S814-003000 S814-103000
2 4
1 3
1 3 2 4
S814-004000 S814-104000
4 - 53
No. of
Receptacle connector (female) Plug connector (male)
pin
3 6
1 4
1 4 3 6
S814-006000 S814-106000
4 8
1 5
1 5 4 8
S814-008000 S814-108000
4 12
1 9
12
4 12
1 9
S814-012000 S814-112000
3 14
1 11
14
1 11 3 14
S814-014000 S814-114000
4 - 54
4) CN TYPE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1 1
S810-001202 S810-101202
2 2
1 1
S810-002202 S810-102202
3 2
1 2 1 3
S810-003202 S810-103202
2 4 1 3
1 3 2 4
S810-004202 S810-104202
4 - 55
No. of
Receptacle connector (female) Plug connector (male)
pin
3 6 1 4
1 4 3 6
S810-006202 S810-106202
4 8 1 5
1 5 4 8
S810-008202 S810-108202
4 - 56
5) 375 FASTEN TYPE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1 2 1 2
S810-002402 S810-102402
No. of
Receptacle connector (female) Plug connector (male)
pin
12
1
1 13
24
36
36 25
13 12
24
25 36
344111-1 344108-1
85202-1
4 - 57
8) AMP 040 MULTILOCK CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
12 1 6
7 12
174045-2
1 6
14
7 14
173852
6
6
1
4
925276-0
4 - 58
11) KET 090 CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1
2
MG610070
1
2
MG640605
2 1
MG640795
4 - 59
13) KET SDL CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
14
7
6
14
MG610406
4 - 60
14) DEUTSCH DT CONNECTORS
DT 06 - 3S - ★★★★
1 2 2 1
DT06-2S DT04-2P
2 1 1 2
3 3
DT06-3S DT04-3P
4 1 1 4
3 2 2 3
DT06-4S DT04-4P
4 - 61
No. of
Receptacle connector (female) Plug connector (male)
pin
6 1 1 6
4 3 3 4
DT06-6S DT04-6P
4 5 5 4
1 8
8 1
DT06-8S DT04-8P
7 6
6 7
12
1 12 12 1
DT06-12S DT04-12P
4 - 62
15) MOLEX 2CKTS CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1 2
35215-0200
35215-0200
2
10
1 10
SWF593757
1
1
NMWP01F-B
4 - 63
18) ECONOSEAL J TYPE CONNECTORS
No. of
Receptacle connector (female) Plug connector (male)
pin
S816-001002 S816-101002
1 2 2 1
S816-002002 S816-102002
S816-003002 S816-103002
S816-004002 S816-104002
4 - 64
No. of
Receptacle connector (female) Plug connector (male)
pin
S816-006002 S816-106002
S816-008002 S816-108002
10
S816-010002 S816-110002
12
S816-012002 S816-112002
4 - 65
No. of
Receptacle connector (female) Plug connector (male)
pin
15
368301-1 2-85262-1
12040753
J K
K J
B
23 N T
A B
F
F Q N
Q A
HD36-24-23SN HD34-24-23PN
4 - 66
21) DEUTSCH MCU CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
5
1 6
11 1
10
2
3
11 4
5
21
6
40 21 31
32
7
8
9
33 10
34
35
31 36
37
20
30
20
38
39
35 40
36
30
40
DRC26-40SA/B
C
D
E
A
9
F
B
G
H J
HD10-9-96P
3 2
2-967325-3
4 - 67
24) DEUTSCH INTERMEDIATE CONNECTOR
No. of
Receptacle connector (female) Plug connector (male)
pin
1
13 12
25 24
31
60 30
37
36
49
48
60
DRB16-60SAE-L018
4 - 68
SECTION 5 MECHATRONICS SYSTEM
The CAPO (Computer Aided Power Optimization) system controls engine and pump mutual power at
an optimum and less fuel consuming state for the selected work by mode selection, auto-deceleration,
power boost function, etc. It monitors machine conditions, for instance, engine speed, coolant
temperature, hydraulic oil temperature, and hydraulic oil pressure, etc.
It consists of a MCU, a cluster, an accel actuator, EPPR valves, and other components. The MCU and
the cluster protect themselves from over-current and high voltage input, and diagnose malfunctions
caused by short or open circuit in electric system, and display error codes on the cluster.
Anti-restart system
MCU & cluster protection
Self-diagnostic system Open-short diagnosis & error code display
Machine error code display
Machine condition monitoring
Machine monitoring system
Electric signal monitoring
5-1
SYSTEM DIAGRAM (CLUSTER TYPE 1)
MCV
Option C
(Dozer)
Option B Bucket
Option A &
Arm 1 Arm regen
SOLENOID VALVE EPPR VALVE
Boom 2 Arm 2
Travel speed Attachment
pressure Swing Boom 1
P1
Overload pressure
pressure
sensor Boom P2
cylinder pressure
Engine
Signal
Pressure signal
Pressure signal
Drive signal
Drive signal MCU
Switch signal Pressure signal
Serial communication(-)
Serial communication(+)
SL SR AO AI BI BU
Shuttle
block
Swing Boom up
pressure sensor pressure sensor Rear view camera
Cluster
1409S5MS01
5-2
SYSTEM DIAGRAM (CLUSTER TYPE 2)
Work Travel
pressure pressure
MCV
Option C
(Dozer)
Option B Bucket
Option A &
Arm 1 Arm regen
SOLENOID VALVE EPPR VALVE
Boom 2 Arm 2
Travel speed
Swing Boom 1
P1
Overload pressure
pressure
sensor Boom P2
cylinder pressure
Engine
A1 A2
Coolant Main pump A3
temp sensor P3
pressure
Signal
Engine speed sensor signal
Pressure signal Pressure signal
Drive signal
MCU Drive signal
Pressure signal
Switch signal Accel dial signal CN-16A CN-16
Normal
Power boost CN-16B
button
One touch Horn button Emergency
decel button
Option Accel dial
LH control button RH control
lever lever
SL SR AO AI BI BU Serial communication(-)
Serial communication(+)
Shuttle
block
Cluster
1409S5MS51
5-3
GROUP 2 MODE SELECTION SYSTEM (CLUSTER TYPE 1)
Engine
Drive signal
Cluster
Engine speed sensor signal
MCU
Normal
CN-16B
Emergency
Power mode
pilot lamp Accel dial
1409S5MS02
Mode selection system (micro computer based electro-hydraulic pump and engine mutual control
system) optimizes the engine and pump performance.
The combination of 3 power modes (P, S, E) and accel dial position (10 set) makes it possible to use
the engine and pump power more effectively corresponding to the work conditions from a heavy and
great power requesting work to a light and precise work.
P Heavy duty power 2150±50 1950±50 2200±50 2000±50 360±30 9.5±2.5 290±30 8
S Standard power 2050±50 1850±50 2100±50 1900±50 400±30 12.5±2.5 330±30 10±3
E Economy operation 1950±50 1750±50 2000±50 1800±50 400±30 12.5±2.5 400±30 12.5±2.5
AUTO Engine
1150±100 - 1150±100 - 700±30 38±3 700±30 38±3
DECEL deceleration
One touch Engine quick
1050±100 - 1050±100 - 700±30 38±3 700±30 38±3
decel deceleration
KEY Key switch
1050±100 - 1050±100 - 700±30 38±3 700±30 38±3
START start position
※ Power shift (Standard/Option) can be changed by "Service menu" in "Management" on the cluster.
5-4
2. WORK MODE SELECTION SYSTEM
Work mode consists of the general operation (bucket) and the optional attachment (breaker,
crusher).
Engine
Cluster
Drive signal
Drive signal
MCU
Pressure signal
Normal
CN-16B
Emergency
Work mode
pilot lamp Work mode switch signal Accel dial
1409S5MS03
5-5
3. USER MODE SELECTION SYSTEM
Engine
Drive signal
Cluster
Engine speed sensor signal
MCU
Normal
CN-16B
Emergency
1409S5MS04
1) High idle rpm, auto idle rpm and EPPR pressure can be adjusted and memorized in the U-mode.
2) LCD segment vs parameter setting
Step Engine speed Idle speed Power shift
( ) (rpm) (rpm) (bar)
1 1550 1050 (low idle) 0
2 1600 1100 3
3 1700 1150 (decel rpm) 6
4 1800 1200 9
5 1900 1250 12
6 2000 1300 16
7 2050 1350 20
8 2100 1400 26
9 2150 1450 32
10 2200 1500 38
5-6
■ MODE SELECTION SYSTEM (CLUSTER TYPE 2)
1. POWER MODE SELECTION SYSTEM
Engine
Drive signal
Engine speed sensor signal
MCU
Power mode
pilot lamp Accel dial signal CN-16A CN-16
CN-16B
Emergency
Accel dial
Cluster
1409S5MS52
Mode selection system (micro computer based electro-hydraulic pump and engine mutual control
system) optimizes the engine and pump performance.
The combination of 3 power modes (M, H, S) and accel dial position (10 set) makes it possible to use
the engine and pump power more effectively corresponding to the work conditions from a heavy and
great power requesting work to a light and precise work.
※ Power shift (Standard/Option) can be changed by "Service menu" in "Management" on the cluster.
5-7
2. WORK MODE SELECTION SYSTEM
2 Work mode can be selected for the optional work speed of the machine operation.
Option C
(Dozer)
Option B Bucket
Option A &
Arm 1 Arm regen
Boom 2 Arm 2
Swing Boom 1
Travel(RH) Travel(LH)
Straight
travel
Engine
Drive signal
MCU
Work mode Accel dial signal CN-16A CN-16
pilot lamp Normal
Accel dial
Cluster
1409S5MS53
5-8
3. USER MODE SELECTION SYSTEM
An operator can change the engine and pump and memorize it for his preference.
Mode Operation
EPPR
7 2050 1350 450
8 2100 1400 500
9 2150 1450 550
10 2200 1500 600
2209S4OP09
5-9
GROUP 3 AUTOMATIC DECELERATION SYSTEM (CLUSTER TYPE 1)
Work Travel
pressure pressure
Cluster
Drive signal
Engine speed sensor signal
Pressure signal
MCU
Accel dial signal CN-16A CN-16
Normal
User mode
CN-16B
pilot lamp Emergency
Engine rpm
Accel dial
set rpm
5-10
■ AUTOMATIC DECELERATION SYSTEM (CLUSTER TYPE 2)
Work Travel
pressure pressure
Drive signal
Auto decel pilot lamp
Engine speed sensor signal
Pressure signal
MCU
Auto decel switch signal Accel dial signal CN-16A CN-16
Normal
Cluster
CN-16B
Emergency
Accel dial
1409S5MS55
Engine rpm
Accel dial
set rpm
5-11
GROUP 4 POWER BOOST SYSTEM (CLUSTER TYPE 1)
Main control valve
Option C
(Dozer)
Option B Bucket
Option A &
Arm 1 Arm regen
Boom 2 Arm 2
Swing Boom 1
Travel(RH) Travel(LH)
Straight
travel
Main relief
valve
P1 P2
pressure pressure
Power boost
solenoid valve
Engine
Normal
CN-16B
Emergency
Cluster 1409S5MS07
· When the power boost switch on the left control lever knob is pushed ON, the power mode is set P
mode and maximum digging power is increased by 10 %.
· When the power boost function is activated, the power boost solenoid valve pilot pressure raises the
set pressure of the main relief valve to increase the digging power.
Description Condition Function
- Power mode : P
- Accel dial power : 9
Power boost switch : ON
Activated - Power boost solenoid : ON
Accel dial : over 8
- Power boost pilot lmap : ON
- Operating time : max 8 seconds
- Pre-set power mode
Canceled Power boost switch : OFF - Power boost solenoid : OFF
- Power boost pilot lamp : OFF
※ When the auto power boost is set to Enable and power mode is set to P mode on the cluster, the
digging power is automatically increased as working conditions by the MCU. It is operated max 8
seconds.
5-12
■ POWER BOOST SYSTEM (CLUSTER TYPE 2)
Main control valve
Option C
(Dozer)
Option B Bucket
Option A &
Arm 1 Arm regen
Boom 2 Arm 2
Swing Boom 1
Travel(RH) Travel(LH)
Straight
travel
Main relief
valve
P1 P2
pressure pressure
Power boost
solenoid valve
Engine
Normal
Cluster CN-16B
Emergency
Accel dial
1409S5MS57
· When the power boost switch on the left control lever knob is pushed ON, the maximum digging
power is increased by 10 %.
· When the power set is at M, H or S and the power boost function is activated, the power boost
solenoid valve pilot pressure raises the set pressure of the main relief valve to increase the digging
power.
Power boost switch
Description
OFF ON
H or S H
Power set
M M
2
Main relief valve set pressure 350 kgf/cm 380 kgf/cm2
Even when pressed continuously,
Time of operation -
it is canceled after 8 sec.
※ Default - Power boost solenoid valve : OFF
5-13
GROUP 5 TRAVEL SPEED CONTROL SYSTEM (CLUSTER TYPE 1)
Option C
(Dozer) Travel motor
Option B Bucket
Option A &
Arm 1 Arm regen
Swing Boom 1
Travel(RH) Travel(LH)
Straight Travel speed
travel solenoid valve
Engine
Cluster
Drive signal
MCU
Travel speed
pilot lamp
1409S5MS08
Travel speed can be switched manually by pressing the travel speed switch on the cluster.
5-14
■ TRAVEL SPEED CONTROL SYSTEM (CLUSTER TYPE 2)
Option C
(Dozer) Travel motor
Option B Bucket
Option A &
Arm 1 Arm regen
Swing Boom 1
Travel(RH) Travel(LH)
Straight Travel speed
travel solenoid valve
Engine
Cluster
1409S5MS58
Travel speed can be switched manually by pressing the travel speed switch on the cluster.
Travel speed Lamp
Speed Operation
solenoid valve on cluster
Low OFF Turtle Low speed, high driving torque in the travel motor
High ON Rabbit High speed, low driving torque in the travel motor
※ Default : Turtle (low)
5-15
GROUP 6 AUTOMATIC WARMING UP SYSTEM (CLUSTER TYPE 1)
Engine
Drive signal
MCU
Accel dial signal CN-16A CN-16
Warming up pilot lamp signal
Normal
CN-16B
Emergency
1409S5MS09
1. The MCU reads engine coolant temperature through the temperature sensor and if the coolant
temperature is below 30˚C, it increases the engine speed from key start rpm to 1150 rpm. At this
time the mode does not change. If the coolant temperature sensor has fault, the hydraulic oil
temperature signal is substituted.
2. In case of the coolant temperature increases up to 30˚C, the engine speed is decreased to key start
speed. And if an operator changes power mode set during the warming up function, the MCU
cancels the automatic warming up function.
3. LOGIC TABLE
5-16
■ AUTOMATIC WARMING UP SYSTEM (CLUSTER TYPE 2)
Engine
Drive signal
Normal
CN-16B
Emergency
Accel dial
1409S5MS59
1. The MCU reads engine coolant temperature through the temperature sensor and if the coolant
temperature is below 30˚C, it increases the engine speed from key start rpm to 1150rpm. At this
time the mode does not change. If the coolant temperature sensor has fault, the hydraulic oil
temperature signal is substituted.
2. In case of the coolant temperature increases up to 30˚C, the engine speed is decreased to key start
speed. And if an operator changes power mode set during the warming up function, the MCU
cancels the automatic warming up function.
3. LOGIC TABLE
5-17
GROUP 7 ENGINE OVERHEAT PREVENTION SYSTEM (CLUSTER TYPE 1)
Engine
Drive signal
Coolant temp sensor
Coolant temp signal
Normal
CN-16B
Emergency
Cluster
Coolant temperature Accel dial
warning lamp
1409S5MS10
1. If the engine coolant temperature or the hydraulic oil temperature is overheated over 103˚C, the
warning lamp is ON and the pump input torque or the engine speed is reduced as below logic table.
2. LOGIC TABLE
Description Condition Function
- Coolant or hydraulic oil temperature : - Warning lamp buzzer : ON
Activated
First step Above 100˚C - Pump absorption torque is reduced.
warning - Coolant or hydraulic oil temperature : - Return to pre-set the pump absorption
Canceled
Less than 95˚C torque.
- Emergency warning lamp pops up on the
- Coolant or hydraulic oil temperature :
Activated center of LCD and the buzzer sounds.
Above 105˚C
Second step - Engine speed is reduced after 10 seconds.
warning - Return to pre-set the engine speed.
- Coolant or hydraulic oil temperature :
Canceled - Hold pump absorption torque on the first
Less than 101˚C
step warning.
5-18
■ ENGINE OVERHEAT PREVENTION SYSTEM (CLUSTER TYPE 2)
Engine
Drive signal
Normal
CN-16B
Emergency
Accel dial
Cluster
1409S5MS60
1. If the engine coolant temperature or the hydraulic oil temperature is overheated over 100˚C, the
warning lamp is ON and the pump input torque or the engine speed is reduced as below logic table.
2. LOGIC TABLE
Description Condition Function
- Coolant or hydraulic oil temperature : - Warning lamp : ON
Activated
First step Above 100˚C - Pump absorption torque is reduced.
warning - Coolant or hydraulic oil temperature : - Return to pre-set the pump absorption
Canceled
Less than 95˚C torque.
- Emergency warning lamp pops up on the
- Coolant or hydraulic oil temperature :
Activated center of LCD and the buzzer sounds.
Above 105˚C
Second step - Engine speed is reduced after 10 seconds.
warning - Return to pre-set the engine speed.
- Coolant or hydraulic oil temperature :
Canceled - Hold pump absorption torque on the first
Less than 100˚C
step warning.
5-19
GROUP 8 VARIABLE POWER CONTROL SYSTEM (CLUSTER TYPE 1)
P1 pressure P2 pressure
Engine
Signal
Normal
CN-16B
Emergency
AO AI BI BU
Boom up
pressure
E mode power
Cluster
1409S5MS11
· The variable power control system controls the engine and pump mutual power according to RCV
lever stroke and pump load.
It makes fuel saving and smooth control at precise work.
Power mode E
Work mode General (bucket)
Pressure sensor Normal
※ The variable power control function can be activated when the power mode is set to E mode.
5-20
GROUP 9 ATTACHMENT FLOW CONTROL SYSTEM (CLUSTER TYPE 1)
Engine
Cluster
Drive signal
Drive signal
MCU
Pressure signal
Normal
CN-16B
Emergency
Work mode
pilot lamp Work mode switch signal Accel dial
1409S5MS03
· The system is used to control the pump delivery flow according to set of the work tool on the
cluster by the attachment flow EPPR valve.
Work tool
Description
Breaker Crusher
Max 7 step, Max 4 step,
Flow level reduced 10 lpm each step reduced 20 lpm each step
Attach safety solenoid ON ON
Attach pressure solenoid OFF ON
Attach conflux solenoid OFF ON / OFF
※ Refer to the page 5-50 for the attachment kinds and max flow.
5-21
GROUP 10 ANTI-RESTART SYSTEM
Engine
Starter
Fuel injection
pump
Accel
actuator P M
Drive signal
MCU
Normal
CN-16B
Emergency
Accel dial
1409S5MS12
1. ANTI-RESTART FUNCTION
After a few seconds from the engine starts to run, MCU turns off the start safety relay to protect the
starter from inadvertent restarting.
2. When a replacement or taking-off of the MCU is needed, connect CN-16 and CN-16B to ensure the
engine start without the MCU.
5-22
GROUP 11 SELF-DIAGNOSTIC SYSTEM (CLUSTER TYPE 1)
1. OUTLINE
When any abnormality occurs in the ADVANCED CAPO system caused by electric parts malfunction
and by open or short circuit, the MCU diagnoses the problem and sends the error codes to the
cluster and also stores them in the memory.
2. MONITORING
1) Active fault
21093CD66
21093CD66A-1 21093CD66B
2) Logged fault
21093CD66C
21093CD66D-1 21093CD66E
3) Delete fault
21093CD66F
21093CD66G 21093CD66H
5-23
3. MACHINE ERROR CODES TABLE
Error code
Description
HCESPN FMI
3 Hydraulic oil temperature sensor circuit - Voltage above normal, or shorted to high source.
101
4 Hydraulic oil temperature circuit - Voltage below normal, or shorted to low source.
0 Working pressure sensor data above normal range.
1 Working pressure sensor data below normal range.
105
2 Working pressure sensor data error.
4 Working pressure sensor circuit - Voltage below normal, or shorted to Low source.
0 Travel oil pressure sensor data above normal range.
1 Travel oil pressure sensor data below normal range.
108
2 Travel oil pressure sensor data error.
4 Travel oil pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Main pump 1 (P1) pressure sensor data above normal range.
1 Main pump 1 (P1) pressure sensor data below normal range.
120 2 Main pump 1 (P1) pressure sensor data error.
Main pump 1 (P1) pressure sensor circuit - Voltage below normal, or shorted to low
4
source.
0 Main pump 2 (P2) pressure sensor data above normal range.
1 Main pump 2 (P2) pressure sensor data below normal range.
121 2 Main pump 2 (P2) pressure sensor data error.
Main pump 2 (P2) pressure sensor circuit - Voltage below normal, or shorted to low
4
source.
0 Overload pressure sensor data above normal range.
1 Overload pressure sensor data below normal range.
122
2 Overload pressure sensor data error.
4 Overload pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Negative 1 pressure sensor data above normal range.
1 Negative 1 pressure sensor data below normal range.
123
2 Negative 1 pressure sensor data error.
4 Negative 1 pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Negative 2 Pressure sensor data above normal range.
1 Negative 2 Pressure sensor data below normal range.
124
2 Negative 2 Pressure sensor data error.
4 Negative 2 Pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Pilot pump (P3) pressure sensor data above normal range.
1 Pilot pump (P3) pressure sensor data below normal range.
125
2 Pilot pump (P3) pressure sensor data error.
4 Pilot pump (P3) pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Boom up pilot pressure sensor data above normal range.
1 Boom up pilot pressure sensor data below normal range.
127
2 Boom up pilot pressure sensor data error.
4 Boom up pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Swing pilot pressure sensor data above normal range.
1 Swing pilot pressure sensor data below normal range.
135
2 Swing pilot pressure sensor data error.
4 Swing pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
※Some error codes are not applied to this machine.
5-24
Error code
Description
HCESPN FMI
0 Attachment pilot pressure sensor data above normal range.
1 Attachment pilot pressure sensor data below normal range.
138
2 Attachment pilot pressure sensor data error.
4 Attachment pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
5 Pump EPPR valve circuit - Current below normal, or open circuit.
140
6 Pump EPPR valve circuit - Current above normal.
5 Boom priority EPPR valve circuit - Current below normal, or open circuit.
141
6 Boom priority EPPR valve circuit - Current above normal.
5 Travel EPPR valve circuit - Current below normal, or open circuit.
143
6 Travel EPPR valve circuit - Current above normal.
5 Attachment flow EPPR valve circuit - Current below normal, or open circuit.
144
6 Attachment flow EPPR valve circuit - Current above normal.
5 Remote cooling fan EPPR valve circuit - Current below normal, or open circuit.
145
6 Remote cooling fan EPPR valve circuit - Current above normal.
5 Left rotate EPPR valve circuit - Current below normal, or open circuit.
150
6 Left rotate EPPR valve circuit - Current above normal.
5 Right rotate EPPR valve circuit - Current below normal, or open circuit.
151
6 Right rotate EPPR valve circuit - Current above normal.
5 Left tilt EPPR valve circuit - Current below normal, or open circuit.
152
6 Left tilt EPPR valve circuit - Current above normal.
5 Right tilt EPPR valve circuit - Current below normal, or open circuit.
153
6 Right tilt EPPR valve circuit - Current above normal.
5 Power max solenoid circuit - Current below normal, or open circuit.
166
6 Power max solenoid circuit - Current above normal.
5 Travel speed solenoid circuit - Current below normal, or open circuit.
167
6 Travel speed solenoid circuit - Current above normal.
5 Attachment pressure solenoid circuit - Current below normal, or open circuit.
168
6 Attachment pressure solenoid circuit - Current above normal.
5 Attachment conflux solenoid circuit - Current below normal, or open circuit.
169
6 Attachment conflux solenoid circuit - Current above normal.
5 Arm regeneration solenoid circuit - Current below normal, or open circuit.
170
6 Arm regeneration solenoid circuit - Current above normal.
5 Attachment safety solenoid circuit - Current below normal, or open circuit.
171
6 Attachment safety solenoid circuit - Current above normal.
5 Remote cooling fan reverse solenoid circuit - Current below normal, or open circuit.
181
6 Remote cooling fan reverse solenoid circuit - Current above normal.
5 Fuel level sensor circuit - Voltage above normal, or shorted to high source.
301
6 Fuel level sensor circuit - Voltage below normal, or shorted to low source.
Engine coolant temperature sensor circuit - Voltage above normal, or shorted to high
3
source.
304
Engine coolant temperature sensor circuit - Voltage below normal, or shorted to low
4
source.
310 8 Engine speed signal error - Abnormal frequency or pulse width.
3 Engine preheat relay circuit - Voltage above normal, or shorted to high source.
322
4 Engine preheat relay circuit - Voltage below normal, or shorted to low source.
3 Fuel warmer relay circuit - Voltage above normal, or shorted to high source.
325
4 Fuel warmer relay circuit - Voltage below normal, or shorted to low source.
※Some error codes are not applied to this machine.
5-25
Error code
Description
HCESPN FMI
3 Potentiometer (G/A) circuit - Voltage above normal, or shorted to high source.
340
4 Potentiometer (G/A) circuit - Voltage below normal, or shorted to low source.
5 Governor actuator circuit - Current below normal, or open circuit.
341
6 Governor actuator circuit - Current above normal.
0 Transmission oil pressure sensor data above normal range.
1 Transmission oil pressure sensor data below normal range.
501
2 Transmission oil pressure sensor data error.
4 Transmission oil pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Brake pressure sensor data above normal range.
1 Brake pressure sensor data below normal range.
503
2 Brake pressure sensor data error.
4 Brake pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Working brake pressure sensor data above normal range.
1 Working brake pressure sensor data below normal range.
505
2 Working brake pressure sensor data error.
4 Working brake pressure sensor circuit - Voltage below normal, or shorted to low source.
3 Working brake lamp circuit - Voltage above normal, or shorted to high source.
506
4 Working brake lamp circuit - Voltage below normal, or shorted to low source.
3 Ram lock lamp circuit - Voltage above normal, or shorted to high source.
520
4 Ram lock lamp circuit - Voltage below normal, or shorted to low source.
5 Ram lock solenoid circuit - Current below normal, or open circuit.
525
6 Ram lock solenoid circuit - Current above normal.
0 Travel F pilot pressure sensor data above normal range.
1 Travel F pilot pressure sensor data below normal range.
530
2 Travel F pilot pressure sensor data error.
4 Travel F pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
0 Travel R pilot pressure sensor data above normal range.
1 Travel R pilot pressure sensor data below normal range.
531
2 Travel R pilot pressure sensor data error.
4 Travel R pilot pressure sensor circuit - Voltage below normal, or shorted to low source.
3 Hourmeter circuit - Voltage above normal, or shorted to high source.
701
4 Hourmeter circuit - Voltage below normal, or shorted to low source.
0 MCU input voltage high.
705
1 MCU input voltage low.
707 1 Alternator node I voltage low.
3 Acc. dial circuit - Voltage above normal, or shorted to high source.
714
4 Acc. dial circuit - Voltage below normal, or shorted to low source.
3 Rotate signal input circuit - Voltage above normal, or shorted to high source.
715
4 Rotate signal input circuit - Voltage below normal, or shorted to low source.
3 Tilt signal input circuit - Voltage above normal, or shorted to high source.
716
4 Tilt signal input circuit - Voltage below normal, or shorted to low source.
3 Travel alarm (buzzer) circuit - Voltage above normal, or shorted to high source.
722
4 Travel alarm (buzzer) circuit - Voltage below normal, or shorted to low source.
830 12 MCU internal memory error.
840 2 Cluster communication data error.
843 2 Option #1 (CAN 2) communication data error.
850 2 RMCU communication data error.
※Some error codes are not applied to this machine.
5-26
■ SELF-DIAGNOSTIC SYSTEM (CLUSTER TYPE 2)
1. OUTLINE
When any abnormality occurs in the NEW CAPO system caused by electric parts malfunction and
by open or short circuit, the MCU diagnoses the problem and sends the error codes to the cluster
and also stores them in the memory.
(error display)
5-27
3. MACHINE ERROR CODES TABLE (CLUSTER TYPE 2)
Error code No. Description
1 Short circuit in accel actuator system
2 Potentiometer circuit is shorted to Vcc (5V) or battery +
3 Short circuit in pump EPPR valve system
4 Short circuit in boom down EPPR valve system
5 Short circuit in travel speed solenoid system
6 Short circuit in power boost solenoid system
7 Short circuit in max flow solenoid system
10 Short circuit in hour-meter system
11 Accel dial circuit is shorted to Vcc(5V) or battery +
12 P1 pressure sensor circuit is shorted to power supply (24V) line
13 P2 pressure sensor circuit is shorted to power supply (24V) line
14 P3 pressure sensor circuit is shorted to power supply (24) line
15 Boom down pressure circuit is shorted to power supply (24V) line
16 Accel actuator circuit is open or shorted to ground
17 Potentiometer circuit is open or shorted to ground
18 Pump EPPR valve circuit is open or shorted to ground
19 Boom down EPPR valve circuit is open or shorted to ground
20 Travel speed solenoid circuit is open or shorted to ground
21 Power boost solenoid circuit is open or shorted to ground
22 Max flow solenoid circuit is open or shorted to ground
25 Hour-meter circuit is open or shorted to ground
26 Accel dial circuit is open or shorted to ground
27 P1 pressure sensor circuit is open or shorted to ground
28 P2 pressure sensor circuit is open or shorted to ground
29 P3 pressure sensor circuit is open or shorted to ground
30 Boom down pressure sensor circuit is open or shorted to ground
31 Engine preheater circuit is open or shorted to ground
32 Travel alarm buzzer circuit is open or shorted to ground
33 Alternator circuit is open or shorted to ground
34 Controller input voltage is below 18V
35 Controller input voltage is over 38V
36 Communication error with cluster
37 Engine speed sensor circuit is open or shorted to ground
38 Anti-restart relay circuit is open or shorted to ground
39 Accel actuator does not stop at a target position
40 There is more than 500rpm difference between target speed and actual speed
5-28
Error code No. Description
41 Hydraulic oil temperature sensor circuit is shorted to ground
42 Fuel level sensor circuit is shorted to ground
43 Coolant temperature sensor circuit is shorted to ground
44 Boom up pressure sensor circuit is shorted to power supply (24V) line
45 Hydraulic oil temperature sensor circuit is open or shorted to battery +
46 Fuel level sensor circuit is open or shorted to battery +
47 Coolant temperature sensor circuit is open or shorted to battery +
48 Boom up pressure sensor circuit is open or shorted to ground
49 Engine preheater circuit is shorted to battery +
51 Boom priority solenoid circuit is open or shorted to ground
56 Travel alarm buzzer circuit is shorted to battery +
58 Boom priority solenoid circuit is shorted to battery +
5-29
GROUP 12 ENGINE CONTROL SYSTEM
1409S5MS13
2. MCU ASSEMBLY
1) To match the pump absorption torque with the engine torque, MCU varies EPPR valve output
pressure, which control pump discharge amount whenever feedbacked engine speed drops under
the reference rpm of each mode set.
2) Three LED lamps on the MCU display as below.
G is turned ON Normal -
5-30
3. EXCHANGE METHOD OF THE ROM IN
THE CLUSTER (TYPE 2) Cluster bracket 1
2 22
22
1409S5MS14
Upper case
Cluster
1409S5MS15
Same
direction
21075MS14
5-31
GROUP 13 EPPR VALVE (CLUSTER TYPE 1)
21093CD67M
21093CD67N 21093CD67P
Enter the password
21093CD67ZZ
· Power shift (standard/option) : Power shift pressure can be set by option menu.
5-32
3) OPERATING PRINCIPLE (CLUSTER TYPE 1, 2)
(1) Structure (pump EPPR valve)
6 7
2 3 4 5
5-22(1)
A
P Pilot oil supply line (pilot pressure)
P
T Return to tank
T
A Secondary pressure to flow regulator at main pump
(2) Neutral
eutral
Pressure line is blocked and A oil returns
to tank.
P A
P T
T
A
(3) Operating
perating
Secondary pressure enters into A.
P A
T
P T
A
5-22(2)
5-33
4) EPPR VALVE CHECK PROCEDURE Spec : 100~700 mA
(CLUSTER TYPE 1, 2)
Adapter(P/no.:21Q6-50410)
(1) Check electric current value at EPPR valve
EPPR valve
Η Disconnect connector CN-75 from Multimeter
CN-75
EPPR valve.
Θ Insert the adapter to CN-75 and install
multimeter as figure. Valve casing
Ι Start engine.
Κ Set S-mode and cancel auto decel
mode.
Λ Position the accel dial at 10. Main pump
(2) Check pressure at EPPR valve Spec : 2~25 kgf/cm2 (30~350 psi)
Η Remove plug and connect pressure
gauge as figure. Pressure adjusting Pilot pressure
ÂGauge capacity : 0 to 50 kgf/cm2 screw locknut supply line
5-34
2. BOOM PRIORITY EPPR VALVE (CLUSTER TYPE 1, 2)
1) COMPOSITION
The boom priority EPPR valve is built in a manifold and mainly consisting of valve body and coil.
This EPPR valve installed under the solenoid valve.
2) CONTROL
The boom priority EPPR valve has to be controlled by a specific electronic amplifier card, which is
supplying the coil with a current 580 mA at 30̫ and 24 V.
3) OPERATING PRINCIPLE
(1) Structure
1 5 4 6
P T
2 Control spool 3
21095MS14
(2) Operation
In de-energized mode the inlet port (P) is closed and the outlet port (A) is connected to tank port
(T).
In energized mode the solenoid armature presses onto the control spool with a force
corresponding to the amount of current. This will set a reduced pressure at port A. The setting is
proportional to the amount of current applied.
(3) Maximum pressure relief
If a pressure from outside is applied on port A the valve may directly switch to tank port (T) and
protect the system before overload.
5-35
4) EPPR VALVE CHECK PROCEDURE Spec : 400~600 mA
(combined boom up and swing operation)
(1) Check electric current value at EPPR
valve
Η Disconnect connector CN-133 from Solenoid valve
EPPR valve.
Θ Insert the adapter to CN-133 and install Boom priority
multimeter as figure. EPPR valve
Ι Start engine.
Κ If rpm display approx 2050Ü50 rpm check CN-133
electric current in case of combined
boom up and swing operation.
Adapter
Multimeter (P/no.:21Q6-50410)
21095MS15
(2) Check pressure at EPPR valve Spec : 12~37 kgf/cm2 (170~530 psi)
Η Remove hose from A5 port and connect (bucket relief operation)
pressure gauge as figure.
ÂGauge capacity : 0 to 50 kgf/cm2 Pressure
gauge
(0 to 725 psi)
A5
Θ Start engine.
Ι If rpm display approx 2050Ü50 rpm
check pressure at relief position of Solenoid valve
bucket circuit by operating bucket control
lever. Boom priority
EPPR valve
Κ If pressure is not correct, adjust it.
Λ After adjust, test the machine.
21095MS16
5-36
■ EPPR VALVE (CLUSTER TYPE 2)
1. PUMP EPPR VALVE
1) COMPOSITION
EPPR (Electro Proportional Pressure Reducing) valve consists of electro magnet and spool valve
installed at main pump.
(1) Electro magnet valve
Receive electric current from MCU and move the spool proportionally according to the specific
amount of electric current value.
(2) Spool valve
Is the two way direction control valve for pilot pressure to reduce main pump flow.
When the electro magnet valve is activated, pilot pressure enters into flow regulator of main pump.
(3) Pressure and electric current value for each mode
5-37
GROUP 14 MONITORING SYSTEM (CLUSTER TYPE 1)
1. OUTLINE
Monitoring system consists of the monitor part and switch part.
The monitor part gives warnings when any abnormality occurs in the machine and informs the
condition of the machine.
Various select switches are built into the monitor panel, which act as the control portion of the machine
control system.
2. CLUSTER
1) MONITOR PANEL
Time display
Warning lamps
(see page 5-42)
Engine rpm/Tripmeter
(see page 5-41)
4 Pilot lamps
(see page 5-45)
Switches
(See page 5-47)
1409S5MS30
5-38
2) CLUSTER CHECK PROCEDURE
(1) Start key : ON
Η Check monitor
a. Buzzer sounding for 4 seconds with HYUNDAI logo on cluster.
ö If the ESL mode is set to the enable, enter the password to start engine.
Θ After initialization of cluster, the operating screen is displayed on the LCD.
Also, self diagnostic function is carried out.
a. Engine rpm display : 0 rpm
b. Engine coolant temperature gauge : White range
c. Hydraulic oil temperature gauge : White range
d. Fuel level gauge : White range
Ι Indicating lamp state
a. Power mode pilot lamp : E mode or U mode
b. Work mode pilot lamp : General operation mode (bucket)
c. Travel speed pilot lamp : Low (turtle)
5-39
3. CLUSTER CONNECTOR
No. Name Signal
1 Battery 24V 20~32V
2 Signal 3 NTSC Cluster
3 GND -
4 Serial + (TX) 0~5V
5 Power IG (24V) 20~32V
6 Signal 2 NTSC 1 4
7 Camera signal NTSC
8 Serial - (RX) 0~5V CN-56
21095MS17
5-40
2) GAUGE
(1) Operation screen
Default Option 1 Engine coolant temperature gauge
2 Hydraulic oil temperature gauge
3 3 3 Fuel level gauge
1 2
1 4 RPM / Tripmeter display
2
4 4
21093CD07A
※ Operation screen type can be set by the screen type menu of the display.
Refer to page 5-59 for details.
5-41
3) WARNING LAMPS
※ Each warning lamp on the top of the LCD pops up on the center of LCD and the buzzer sounds
when the each warning is happened. The pop-up warning lamp moves to the original position and
blinks when the select switch is pushed. And the buzzer stops.
Refer to page 5-48 for the select switch.
21093CD08B
5-42
(4) Emergency warning lamp
① This lamp pops up and the buzzer sounds when each of the
below warnings is happened.
- Engine coolant overheating (over 105˚C)
- Hydraulic oil overheating (over 105˚C)
- Pump EPPR circuit abnormal or open
21093CD30 - Attachment flow EPPR circuit abnormal or open
- MCU input voltage abnormal
- Accel dial circuit abnormal or open
- Cluster communication data error
※ The pop-up warning lamp moves to the original position and
blinks when the select switch is pushed. Also the buzzer stops.
This is same as following warning lamps.
② When this warning lamp blinks, machine must be checked and
serviced immediately.
21093CD32
21093CD34
21093CD35
5-43
(8) Overload warning lamp (opt)
① When the machine is overload, the overload warning lamp
blinks during the overload switch is ON. (if equipped)
② Reduce the machine load.
21093CD36
5-44
4) PILOT LAMPS
4
6 Work tool mode Oil flow level of breaker or crusher mode
5-45
(3) Preheat pilot lamp
① Turning the start key switch ON position starts preheating in
cold weather.
② Start the engine after this lamp is OFF.
21093CD39
5-46
5) SWITCHES
21093CD45
※ When the switches are selected, the pilot lamps are displayed on the LCD. Refer to the page
3-7 for details.
5-47
(3) User mode switch
① This switch is used to memorize the current machine operating
status in the MCU and activate the memorized user mode.
·Memory : Push more than 2 seconds.
·Action : Push within 2 seconds.
·Cancel : Push this switch once more within 2 seconds.
21093CD45D ② Refer to the page 5-50 for another set of user mode.
21093CD45G
5-48
6) MAIN MENU
Press
21093CD64
21093CD64B
21093CD64A
※ Please refer to select switch, page 5-48 for selection and change of menu and input value.
(1) Structure
No Main menu Sub menu Description
Work tool Breaker, Crusher, Not installed
U mode power User mode only
Boom/Arm speed Boom speed, Arm speed
1
Auto power boost Enable, Disable
Mode Initial mode Default, U mode
21093CD64D Cluster switch (back up) Switch function
Active fault MCU
Logged fault MCU
Delete logged fault All logged fault delete, Initialization canceled
2
Monitoring (analog) Machine information
Monitoring
Monitoring Monitoring (digital) Switch status, Output status
21093CD64E Operating hours Operating hours for each mode
Maintenance information Replacement, Change interval oils and filters
Machine security ESL mode setting, Password change
Machine Information Cluster, MCU, Engine, Machine
3 A/S phone number, A/S phone number change
A/S phone number
Management Service menu
Management Power shift, Hourmeter, Replacement history, Update
21093CD64F
5-49
(2) Mode setup
① Work tool
21093CD65
21093CD65A 21093CD65B
A B
② U mode power
Power
Step Engine Idle speed
speed shift
( ) (rpm) (rpm)
(bar)
1 1550 1050 (low idle) 0
2 1600 1100 3
21093CD65D 3 1700 1150 (decel rpm) 6
4 1800 1200 9
21093CD65E
5 1900 1250 12
· Engine high idle rpm, auto idle rpm and pump torque 6 2000 1300 16
(power shift) can be modulated and memorized sepa- 7 2050 1350 20
rately in U-mode. 8 2100 1400 26
· U-mode can be activated by user mode switch. 9 2150 1450 32
10 2200 1500 38
③ Boom/Arm speed
21093CD65F
21093CD65G
· Boom speed
- Control type
Manual - Boom up speed is fixed as set steps.
Auto - Boom up speed is automatically adjusted as working conditions by the MCU.
- Speed setting - Boom up speed is increased as much as activated steps.
· Arm speed
- Regeneration - Arm regeneration function can be activated or cancelled.
Enable - Arm in speed is up.
Disable - Fine operation.
5-50
④ Auto power boost
21093CD65L
21093CD65M
⑤ Initial mode
21093CD65P
21093CD65Q
· Default - The initial power mode is set E mode when the engine is started.
· U mode - The initial power mode is set U mode when the engine is started.
21093CD65S
21093CD65T
- The cluster switch can be selected and changed by this menu when the switches are abnor-
mal on the cluster.
- In order to exit "Cluster switch" mode, please put the cursor on the ESC/CAM switch by turn-
ing the select switch and push the select switch.
- In "Cluster switch", other switches except "Select switch" do not work.
5-51
(3) Monitoring
① Active fault
21093CD66
21093CD66A-1 21093CD66B
② Logged fault
21093CD66C
21093CD66D-1 21093CD66E
21093CD66F
21093CD66G 21093CD66H
④ Monitoring
Monitoring(Analog)
21093CD66J
21093CD66K 21093CD66L
· The machine status such as the engine rpm, oil temperature, voltage and pressure etc. can
be checked by this menu.
5-52
⑤ Monitoring (digital)
21093CD66M
21093CD66N 21093CD66P
⑥ Operating hours
21093CD66Q
21093CD66R
5-53
(4) Management
① Maintenance information
21093CD67
21093CD67A
21093CD67Q 21093CD67R
21093CD67S 21093CD67T
5-54
② Machine security
21093CD67C
21093CD67D 21093CD67E
· ESL mode
- ESL : Engine Starting Limit
- ESL mode is designed to be a theft deterrent or will pre-
vent the unauthorized operation of the machine.
- If the ESL mode was selected Enable, the password will
be required when the start switch is turned ON.
21093CD67EE
- Disable : Not used ESL function
Enable (always) : The password is required whenever the
operator start engine.
Enable (interval) : The password is required when the op-
erator start engine first. But the operator
can restart the engine within the interval
time without inputting the password.
The interval time can be set maximum 4 21093CD67H
hours.
· Password change
- The password is 5~10 digits.
21093CD67X 21093CD67XX
The new password is stored in the MCU. Enter the new password again
5-55
③ Machine Information
21093CD67F
21093CD67G
· This can confirm the identification of the cluster, MCU, engine and machine.
21093CD67J
21093CD67K 21093CD67L
21093CD67Z 21093CD67Y
⑤ Service menu
21093CD67M
21093CD67N 21093CD67P
Enter the password
21093CD67ZZ
· Power shift (standard/option) : Power shift pressure can be set by option menu.
· Hourmeter : Operating hours since the machine line out can be checked by this menu.
· Replacement history : Replacement history of the MCU and cluster can be checked by this
menu.
· Update : Firm ware can be upgraded by this menu. (the USB port is located under the
cluster)
5-56
(5) Display
① Display item
21093CD68
21093CD68A 21093CD68W
21093CD68B 21093CD68E
Center display
Center display
· The center display type of the LCD can be selected by this menu.
· The engine speed or each of the tripmeter (A,B,C) is displayed on the center display.
② Clock
21093CD68C
21093CD68D
5-57
③ Brightness
21093CD68F
21093CD68G 21093CD68H
Manual (1st~10th step)
21093CD68J 21093CD68K
Auto (day/night)
※ If "Auto" is chosen, brightness for day and night can be differently set up. Also by using the
bar in lower side, users can define which time interval belongs to day and night.
(in bar figure, gray area represents night time while white shows day time)
④ Unit
21093CD68L
21093CD68M 21093CD68N
· Temperature : ˚C ↔˚F
· Pressure : bar ↔ MPa ↔ kgf/cm2
· Flow : lpm ↔ gpm
· Date format : yy/mm/dd ↔ mm/dd/yy ↔ dd-Mar-yy
⑤ Language
21093CD68R
21093CD68S 21093CD68T
· User can select preferable language and all displays are changed the selected language.
5-58
⑥ Screen type
21093CD68U
21093CD68V 21093CD68W
A Type Standard
21093CD68Y
B Type 21093CD68X Option
(6) Utilities
① Tripmeter
21093CD69
21093CD69A 21093CD69B
② DMB
21093CD69C
21093CD69D 21093CD69E
5-59
③ Entertainment
· Play MP4 or codec file of external hard disk through USB port.
· The USB port is located under the cluster.
21093CD69F
21093CD69G
④ Camera setting
21093CD69J
21093CD69K 21093CD69L
21093CD69M 21093CD69N
⑤ Message box
· The history of the machine operating status can be checked by this menu.
21093CD69Q
21093CD69R
5-60
■ MONITORING SYSTEM (CLUSTER TYPE 2)
1. OUTLINE
Monitoring system consists of the monitor part and switch part.
The monitor part gives warnings when any abnormality occurs in the machine and informs the
condition of the machine.
Various select switches are built into the monitor panel, which act as the control portion of the
machine control system.
2. CLUSTER
1) MONITOR PANEL
1409S5MS80
5-61
2) CLUSTER CHECK PROCEDURE
(1) Start key : ON
① Check monitor initial 5 seconds
a. All lamps light up.
b. Buzzer sound.
② Check monitor after 5 seconds : Indicate cluster version and machine condition
a. Cluster program version :「1.00」 Indicates program version「1.00」for 5 seconds.
b. Tachometer : 0rpm
c. Fuel gauge : All light up below appropriate level
d. Hydraulic temperature : All light up below appropriate level
e. Engine coolant temperature gauge : All light up below appropriate level
f. Warning lamp
※ During start key ON the engine oil pressure lamp and battery charging lamp go on, but
it is not abnormal.
※ When engine coolant temperature below 30°C , the warming up lamp lights up.
③ Indicating lamp state
a. Work mode selection : General work
b. Power mode selection : S mode
c. User mode selection : No LED ON
d. Auto decel LED : ON
e. Travel speed pilot lamp : Low (turttle)
(2) Start of engine
① Check machine condition
a. Tachometer indicates at present rpm
b. Gauge and warning lamp : indicate at present condition.
※ When normal condition : All warning lamp OFF
c. Work mode selection : General work
d. Power mode selection : S mode
e. User mode selection : No LED ON
f. Auto decel LED : ON
g. Travel speed pilot lamp : Low (turttle)
② When warming up operation
a. Warming up lamp : ON
b. 10 seconds after engine started, engine speed increases to 1150 rpm (auto decel LED : ON)
※ Others same as above ①.
③ When abnormal condition
a. The lamp lights up and the buzzer sounds.
b. If BUZZER STOP switch is pressed, buzzer sound is canceled but the lamp light up
until normal condition.
5-62
3. CLUSTER CONNECTOR
No. Signal Input / Output
1 4
2 3
21075MS16
5-63
2) LCD MAIN OPERATION DISPLAY
Default screen
screen screen
Option screen 1 Time display
2 2
1 1 2 RPM display
4
4
5
3 Hydraulic oil temperature gauge
3 3
5 4 Fuel level gauge
1607A3CD02A 1607A3CD02B 5 Engine coolant temperature gauge
12th step
① This gauge indicates the temperature of hydraulic oil in 12 step
gauge.
·1st step : Below 30˚C (86˚F)
·2nd~10th step : 30-105˚C (86-221˚F)
1st step ·11th~12th step : Above 105˚C (221˚F)
1607A3CD02D
② The gauge between 2nd and 10th steps illuminates when
operating.
③ Keep idling engine at low speed until the gauge between 2nd
and 10th steps illuminates, before operation of machine.
④ When the gauge of 11th and 12th steps illuminates, reduce
the load on the system. If the gauge stays in the 11th~12th
steps, stop the machine and check the cause of the problem.
(4) Fuel level gauge
1st step ① This gauge indicates the amount of fuel in the fuel tank.
② Fill the fuel when the 1st step or fuel icon blinks in red.
※ If the gauge illuminates the 1st step or fuel icon blinks in
red even though the machine is on the normal condition,
check the electric device as that can be caused by the poor
1607A3CD02E
connection of electricity or sensor.
(5) Engine coolant temperature gauge
12th step
① This gauge indicates the temperature of coolant in 12 step
gauge.
·1st step : Below 30˚C (86˚F)
·2nd~10th step : 30-105˚C (86-221˚F)
1st step
·11th~12th step : Above 105˚C (221˚F)
1607A3CD02F
② The gauge between 2nd and 10th steps illuminates when
operating.
③ Keep idling engine at low speed until the gauge between 2nd
and 10th steps illuminates, before operation of machine.
④ When the gauge of 11th and 12th steps illuminates, turn OFF
the engine, check the radiator and engine.
5-64
3) WARNING OF MAIN OPERATION SCREEN
(1) Warning display
① Engine coolant temperature
- This lamp blinks and the buzzer sounds
when the temperature of coolant is over
the normal temperature 105˚C (221˚F).
- Check the cooling system when the lamp
blinks.
② Fuel level
- This lamp blinks and the buzzer sounds
when the level of fuel is below 31ℓ (8.2
U.S. gal).
- Fill the fuel immediately when the lamp
blinks.
③ Hydraulic oil temperature
- This warning lamp operates and the
buzzer sounds when the temperature of
hydraulic oil is over 105˚C (221˚F).
- Check the hydraulic oil level when the
lamp blinks.
- Check for debris between oil cooler and
radiator.
④ All gauge
- This lamp blinks and the buzzer sounds
when the all gauge is abnormal.
- Check the each system when the lamp
blinks.
⑤ Communication error
- Communication problem between MCU
and cluster makes the lamp blinks and
the buzzer sounds.
- Check if any fuse for MCU burnt off.
If not check the communication line
between them.
(2) Pop-up icon display
No Switch Selected mode Interval No Switch Selected mode Interval
5-65
4) LCD
1 : LCD
SYSTEM MENU
4 : Up/Right Direction
: Select (enter)
5
2 Activate the currently chosen item
4
3 5
2209S3CD05
1 2 3 4
1 : Menu information
: Monitoring
2
- Equipment, Switch, Output
: Diagnosis
3
- Current error, Recorded error
4 : Maintenance
5 6 7
2507A4OP94 : Settings
5 - Time set, Dual mode
- System lock (reserved)
: Display
6
- Operation skin, Brightness, Language
7 : User mode
5-66
(2) Display map
① Monitoring
② Diagnosis
a. Protocol type 1
(error display)
5-67
b. Protocol type 2
- If there are more than 2 error codes, each one can be displayed by pressing or switch
respectively.
- 3 error codes (①SPN200200, ②FMI06, ③SPN6789, ④FMI04, ⑤345) display.
① ② ⑤ No change
① ③ ④
① ③ ③
③ Maintenance
④ Setting
a. Time set
: Adjusting
: Setting
b. System lock - Reserved
5-68
c. Dual mode
- Changing the MCU mode
⑤ Display
a. Operation skin
b. Brightness
c. Language
⑥ User mode
5-69
5) WARNING AND PILOT LAMP
(1) Engine oil pressure warning lamp
① This lamp blinks and the buzzer sounds after starting the
engine because of the low oil pressure.
② If the lamp blinks during engine operation, shut OFF engine
immediately. Check oil level.
21073CD07
21073CD08
21073CD10
21073CD13
21073CD15
5-70
(6) Power max pilot lamp
① The lamp will be ON when pushing power max switch on the LH
RCV lever.
21073CD11
21073CD17
21073CD12
5-71
6) SWITCH PANEL
2209S3CD10
※ When the switches (Work mode, Power mode, Auto decel, Travel speed control) are selected,
the pop-up icon is displayed on the LCD.
Refer to the page 3-25 for details.
1607A3CD21
5-72
(3) Auto deceleration switch
① This switch is used to actuate or cancel the auto deceleration
function.
② When the switch actuated and all control levers and pedals are
at neutral position, engine speed will be lowered automatically
to save fuel consumption.
1607A3CD22
·Light ON : Auto deceleration function is selected.
·Light OFF : a. Auto deceleration function is cancelled so that
the engine speed increased to previous
setting value.
b. One touch decel function is available.
21073CD23
21073CD24
1607A3CD25A
5-73
GROUP 15 F
FUEL
UEL WARMER SYSTEM
1. S
SPECIFICATION
PECIFICATION
1) Operating voltage : 24±4 V
2) Power : 350±50 W
3) Current : 15 A
2. O
OPERATION
PERATION
1) T h e c u r r e n t o f f u e l w a r m e r s y s t e m i s Fuel warmer
automatically controlled without thermostat
according to fuel temperature.
2) At the first state, the 15 A current flows to the fuel
warmer and engine may be started in 1~2 Prefilter
minutes.
3) If the fuel starts to flow, ceramic-disk in the fuel
warmer heater senses the fuel temperature to
reduce the current as low as 1.5 A.
So, fuel is protected from overheating by this
2507A5MS12
mechanism.
3. E
ELECTRIC
LECTRIC CIRCUIT
145 5W
5R
5R
5R
138
CS-74A
FUSE BOX
POWER RY
2
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
2
3
4
5
6
7
8
9
87a 87 85
30 86
30A
30A
30A
20A
20A
10A
30A
30A
20A
30A
20A
20A
20A
20A
20A
20A
20A
20A
10A
ROOM LAMP/CASSETTE 10A
10A
10A
10A
10A
30A
20A
10A
10A
10A
10A
10A
CS-74
BEACON LAMP(OPT)
AIR CON & HEATER
CABIN LAMP(OPT)
CR-35
87a
30
86
85
87
CIGAR LIGHTER
SWITCH PANEL
FUEL HEATER
AC & HEATER
FUEL P/PUMP
START. STOP
CONVERTER
SAFETY SOL
TRAVEL SOL
WORK LAMP
SOLENOIDE
MASTER SW
MCU CONT.
HEAD LAMP
START KEY
0.8WOr
MCU EPPR
CASSETTE
IG POWER
PRE-HEAT
2WR
0.8B
CLUSTER
CLUSTER
2W
OPTION
CN-95
WIPER
SPARE
WIPER
HORN
CN-36
MCU 1.2R
3W
2W
FUSIBLE LINK
CR-1
60R 60B
BATTERY
BATT RY (12VX2)
2W
CN-5
17
18
19
20
21
22
23
24
31
32
33
34
35
36
37
38
39
42
43
44
45
46
47
48
57
58
59
60
3
6
7
8
9
1
4
5
2
1.2R
CN-51
1
CN-52
1.2W
12
BATTERY POWER 24V(+)
CS-2
CR-46
CN-96
FUEL WARMER RY
1
2
3
5
4
4
6
87a
3
30
87
86
85
85 87 87a
B
0, I
1
86 30
FUEL WARMER
MCU
MCU
H 0 I
FUEL WARMER RY
4
3
2
6
5
ST C BR ACC H
5-74
SECTION 6 TROUBLESHOOTING
1. INTRODUCTION
When a trouble is occurred in the machine, this section will help an operator to maintain the machine
with easy.
The trouble of machine is parted Hydraulic & Mechanical system, Electrical system and
Mechatronics system. At each system part, an operator can check the machine according to the
troubleshooting process diagram.
※ Before carring out troubleshooting procedure, check monitoring menu in the cluster.
Hydraulic &
Mechanical part GROUP 2
Mechatronics
Troubles occur GROUP 4
part
6-1
2. DIAGNOSING PROCEDURE
To carry out troubleshooting efficiently, the following steps must be observed.
6-2
STEP 4. Inspect the trouble actually on the
machine
In case that some trouble cannot be confirmed,
obtain the details of the malfunction from the
operator.
Also, check if there are any in complete
connections of the wire harnesses are or not.
(210-7) 6-3(1)
13031SH05
(210-7) 6-3(3)
6-3
GROUP 2 HYDRAULIC AND MECHANICAL SYSTEM
1. INTRODUCTION
1) MACHINE IN GENERAL
(1) If even a minor fault is left intact and operation is continued, a fatal failure may be caused,
entailing a large sum of expenses and long hours of restoration.
Therefore when even a small trouble occurs, do not rely on your intuition and experience, but look
for the cause based on the troubleshooting principle and perform maintenance and adjustment to
prevent major failure from occurring. Keep in mind that a fault results from a combination of
different causes.
(2) The following lists up commonly occurring faults and possible causes with this machine. For the
troubleshooting of the engine, refer to the coming troubleshooting and repair.
(3) When carrying out troubleshooting, do not hurry to disassemble the components.
It will become impossible to find the cause of the problem.
(4) Ask user or operator the following.
Η Was there any strange thing about machine before failure occurred?
Θ Under what conditions did the failure occur?
Ι Have any repairs been carried out before the failure?
(5) Check before troubleshooting.
Η Check oil and fuel level.
Θ Check for any external leakage of oil from components.
Ι Check for loose or damage of wiring and connections.
2) MACHINE STATUS MONITORING ON THE CLUSTER (CLUSTER TYPE 1)
(1) The machine status such as the engine rpm, oil temperature, voltage and pressure etc. can be
checked by this menu.
Note 7
Note 3
Note 5
Note 6
Note 2
Note 1
Analog 1
Analog 1 Analog22
Analog 1409S6HS01
(2) Specification
No. Description Specification
Note 1 Pilot pump pressure 40+20 bar
Note 2 Swing pilot pressure 0~40 bar
Note 3 Boom up pilot pressure 0~40 bar
Note 5 P1 pump control pressure 0~25 bar
Note 6 P2 pump control pressure 0~25 bar
Note 7 Pump 1 pressure 350 bar
6-4
2. DRIVE SYSTEM
1) UNUSUAL NOISE COMES OUT OF PUMP CONNECTION
Cause Remedy
YES
Coupling element Disassemble
is broken. and repair.
Remove dust
plug under engine
flywheel and
YES
check if rubber Replace hub or
pieces or particles retighten
are not present. Coupling hub setscrew.
spline is worn or
NO hub fastening
setscrew is slack.
If hydraulic pump or engine is
suspected as a culprit refer to this
NO
manual "Structure and function".
6-5
2) ENGINE STARTS BUT MACHINE DOES NOT OPERATE AT ALL
Cause Remedy
NO
Replenish
specified oil to
the standard
Is oil level in Abnormal noise level.
hydraulic oil YES comes out of YES
Hydraulic pump is Disassemble
tank within hydraulic pump
standard level? broken. and repair.
Is pilot pump
pressure within ͽ
NO standard level?
See Note 1
YES
Clean pilot
Is pilot piping piping interior or
YES clogged or is oil
repair piping.
leakage present
on pilot piping?
RCV and safety Disassemble
NO
solenoid valve is and repair.
ͽ faulty.
YES
Pilot relief valve in Repair or
gear pump is replace.
Is gear pump
faulty.
NO delivering oil?
6-6
3. HYDRAULIC SYSTEM
1) HYDRAULIC OIL IS CLOUDY
Cause Remedy
YES
Water is mixed. Put hydraulic oil
still, separate
Drop hydraulic oil water and
sample on hot dispose it or
plate and check if replace hydraulic
foams come up. oil.
NO
Air is intruded. Check suction
line and return
line and eliminate
the air intruding
source.
Cause Remedy
NO
Replenish
specified oil to
the standard
Is hydraulic oil level.
volume proper? YES
Oil cooler clogged. Clean oil cooler.
Bypass check Replace
Is oil cooler clogged
and is bypass check valve is defective.
YES valve always open? YES ͽ
Is fan belt
NO tension proper?
Adjust belt
NO tension or
replace belt.
Is not the set
pressure of main YES Readjust set
relief, port relief pressure.
ͽ and travel relief
Is main relief
valve lower than
valve used very YES Reduce load.
the standard NO often?
level?
6-7
3) CAVITATION OCCURS WITH PUMP
Cause Remedy
NO Replenish
specified oil to
the standard
Is hydraulic oil level.
volume proper? YES
Replace oil with
one of proper
Is not viscosity viscosity.
of hydraulic oil
YES YES
too high? Clean suction
Is not suction strainer.
NO strainer clogged? Is not air intruding
from pump Check for air
NO intrusion in
suction line?
suction line and
retighten or
replace parts.
Cause Remedy
YES Replace
Has not hydraulic hydraulic oil to be
oil passed specified.
specified replace-
ment hours? Has return filter
NO
been replaced at Flush with
NO proper intervals?
hydraulic oil and
replace return
filter.
6-8
4. SWING SYSTEM
1) BOTH LH AND RH SWING ACTIONS ARE IMPOSSIBLE
Cause Remedy
NO
Replenish
Does safety YES
ͽ specified oil to the
YES solenoid valve
standard level.
operation
Is gear pump pilot normal? Safety solenoid Repair or replace.
NO
pressure within valve faulty or not
YES standard level?
Is oil in hydraulic operated.
YES tank within
See Note 1 Gear pump faulty. Repair or replace.
standard level? NO
YES
Are broken pieces Pump connection Disassemble and
of coupling present coupling is broken. repair.
ͽ when dust plug
under engine fly Is main relief NO
Are attachment wheel is removed? NO valve faulty? Hydraulic pump is Disassemble and
and travel out of order. repair.
motions
impossible at all? NO
Does swing Swing control valve Disassemble and
YES
control valve spool is stuck. repair.
Is MCV swing spool move?
YES pilot pressure ;
YES
within standard See Note 5
level? Ϳ
Is RH travel See Note 2 NO
NO function normal?
Does not symptom
change when front YES
and rear pump Hydraulic pump is Disassemble and
NO
discharge hoses broken. repair.
are exchanged?
YES
Swing parking Disassemble and
brake release valve repair.
Is swing parking is broken.
; brake release
valve faulty? YES
Swing reduction Disassemble and
Does swing unit is broken. repair.
NO motor rotate?
Swing motor is Disassemble and
NO
broken. repair.
YES
Pilot relief valve in Disassemble and
NO Is gear pump gear pump is faulty. repair or replace.
delivering oil?
Gear pump is out of Disassemble and
NO
Is gear pump pilot order. repair.
Ϳ pressure within
standard level? YES
Is there oil Clean pilot piping
See Note 1 interior or repair
leakage from
YES pilot piping or is it piping.
clogged? RCV is broken. Disassemble and
NO
repair.
6-9
2) SWING SPEED IS LOW
Cause Remedy
YES
Swing port relief Disassemble and
YES Does swing spool valve is faulty. repair or replace.
move?
Swing control valve Disassemble
Is MCV pilot NO
spool is stuck. and repair.
pressure same
on LH and RH YES Clogged or oil
sides? Clean pilot piping
leak. interior or repair
See Note 2 Is pilot piping
Single direction clogged or is it piping.
NO leaking oil?
Is the trouble in RCV or shuttle Disassemble
one direction or NO
valve is faulty. and repair.
in both direction? YES
ͽ
YES Does swing spool
Both directions move?
YES Is MCV pilot Swing spool is Disassemble
pressure within NO
Is Arm speed See Note 5 stuck. and repair.
standard level?
within standard ;
value? See Note 2 NO Ϳ
NO
Is swing motor's NO
ͽ drain rate within Swing motor is Disassemble
standard value? broken. and repair.
Check that pilot
YES piping is clogged NO
or oil is leaking RCV or shuttle Disassemble
from it? valve is faulty. and repair.
6-10
3) SWING MOTION IS IMPOSSIBLE IN ONE DIRECTION
Cause Remedy
YES
Does symptom Swing port relief Disassemble
change when LH
YES valve is faulty. and repair.
and RH port
relief valves are
exchanged? NO Shuttle valve is Disassemble
YES Does swing control faulty. and repair.
valve spool move?
Cause Remedy
YES
Pilot relief valve is Disassemble
faulty. and repair or
YES Is MCV pilot YES Is gear pump pilot
pressure within pressure within replace.
standard value? standard level?
See Note 2 See Note 1 Gear pump is Disassemble
NO
broken. and repair.
YES Does swing spool
move?
RCV is faulty. Disassemble
NO
and repair.
Is swing control
valve's return
spring normal? Swing spool is Disassemble
NO
stuck. and repair.
6-11
5) THE SWING UNIT DRIFTS WHEN THE MACHINE IS AT REST ON A SLOPE
Cause Remedy
YES
ͽ
YES Is swing shuttle
valve normal?
Shuttle valve is Disassemble
NO
faulty. and replace.
YES Is brake spring
normal?
Is return spring
of swing spool Brake spring is Disassemble
NO
normal? faulty. and replace.
6-12
5. TRAVEL SYSTEM
1) TRAVEL DOES NOT FUNCTION AT ALL ON ONE SIDE
Cause Remedy
YES
Does ͽ
YES counterbalance
spool move lightly
by hand? Counter spool is
Is travel brake Disassemble
NO
YES valve pressure stuck. and repair or
within standard replace.
level? Does the symptom
change when
relief valves in YES
Relief valve built Disassemble
NO travel motor are
Has travel spool exchanged? in travel motor is and repair.
YES
changed over faulty.
positively?
YES Control system is Disassemble
defective. inspect and
Does travel spool
repair.
NO move?
NO
Travel spool is Disassemble
stuck. and repair.
Is bucket or arm
operation YES Travel reduction Disassemble
possible? Do not metallic
unit is faulty. and repair.
particles come
ͽ out of drain port
in travel
reduction unit? Travel motor is Disassemble
NO
out of order. and repair.
Does the symptom
NO
change when front YES
and rear pump Hydraulic pump is Disassemble
Does the discharge hoses
symptom change broken. and repair.
are exchanged?
when LH/RH
NO
travel relief valves
are exchanged?
YES
Travel relief Disassemble
valves are faulty. and repair or
replace.
6-13
2) SPEED ON ONE SIDE FALLS AND THE MACHINE CURVES
Cause Remedy
YES
Brake valve is Disassemble
Do LH and RH
travel speeds defective. and repair or
YES change when LH replace.
YES
and RH travel Does the symptom Relief valve built Disassemble
brake valves are change when in travel motor is and repair.
exchanged? relief valves in
faulty.
NO LH and RH
YES Has travel spool travel motors are
changed over exchanged? ͽ
positively? NO
YES
Control system is Disassemble,
faulty . inspect and
Does spool move? repair.
Is the lower NO
speed (bucket or
arm) within See Note 5, 6 Control valve Disassemble
NO
standard level? spool is stuck. and repair.
YES
Travel relief valve Disassemble
Do LH and RH is faulty. and repair or
travel speeds Does the symptom replace.
change over when change when
NO travel relief valves YES front and rear YES
pump discharge Hydraulic pump is Disassemble
are exchanged?
Is external pilot hoses are broken. and repair.
pressure within exchanged?
NO
standard level?
External pilot Disassemble
NO
piping is clogged and clean.
or oil is leaking
Does travel speed from it.
change when
YES parking brake YES
spring in the Travel motor's Disassemble
travel motor is parking brake is and clean pilot
Is drain rate of removed?
ͽ travel motor within not released piping.
standard level? properly.
6-14
3) MACHINE DOES NOT STOP ON A SLOPE
Machine is pulled forward as sprocket rotates during digging operation.
Cause Remedy
None Is parking brake YES
friction plate Friction plate is Disassemble
YES Check if parking worn? faulty. and repair.
brake pilot line is
clogged.
Clogged Disassemble
and clean pilot
Is drain rate of piping.
Is travel brake YES NO
travel motor
pressure within Travel motor is Disassemble
within standard
standard level? defective. and repair.
value?
SPEC : 11kgf/cm2
YES
Cause Remedy
Inspect according
to the procedure
"Travel does not
function at all on
one side."
However, a case
where both LH
and RH travel
motions are
disabled is
Is bucket or arm
operation extremely seldom
possible? statistically.
OK
Hydraulic pump is Disassemble
Disassemble both faulty. and repair.
OK travel relief valves
Remove dust and inspect for
plug under engine any fault.
OK flywheel and Travel relief valve Disassemble
check that there is Faulty is faulty. and repair or
no coupling
replace.
element particles.
Check oil volume Particles present. Coupling at pump
in hydraulic oil connection is Disassemble
NO tank. broken. and repair.
Short Replenish
hydraulic oil.
6-15
5) TRAVEL ACTION IS POWERLESS (travel only)
Cause Remedy
YES
ͽ
Is travel motor's
YES
drain rate within
standard level?
Is travel brake Travel motor is Disassemble
YES NO
pressure within faulty. and repair.
standard level?
Is travel relief
valve pressure Travel brake valve Disassemble
NO
within standard is defective. and repair or
level?
replace.
NO
Travel relief valve Disassemble
is faulty. and repair or
replace.
YES
Hydraulic circuit Disassemble
Does parking that releases and clean.
brake piston travel parking
Increases move lightly by
Remove parking brake is clogged
brake spring in hand?
with dirt.
travel motor,
draw out piston Parking brake Disassemble
ͽ NO
completely, refit piston in travel and repair.
cover and check motor is stuck.
if travel power
changes. Remains
unchanged Travel reduction Disassemble
unit is defective. and repair.
Cause Remedy
Travel brake valve
(counterbalance Disassemble
valve) is faulty. and repair or
replace.
6-16
7) MACHINE MAKES A CURVED TRAVEL OR DOES NOT TRAVEL AT ALL WHEN TRAVEL
AND ATTACHMENT OPERATIONS ARE EXECUTED AT THE SAME TIME
Cause Remedy
YES
Normal.
6-17
6. ATTACHMENT SYSTEM
1) BOOM OR ARM ACTION IS IMPOSSIBLE AT ALL
Cause Remedy
YES
Does the Port relief valve is Disassemble
YES symptom change faulty. and repair or
when port relief replace.
valve is replaced
with other valve? NO ͽ
YES Is MCV pilot
pressure within
standard level?
Inspect if pilot
See Note 3, 4 piping is clogged OK
RCV is faulty. Disassemble
NO or oil is leaking
YES Are other from the piping. and repair.
attachments
operatable?
YES
Pilot relief valve is Disassemble
Is gear pump
pilot pressure YES Is gear pump faulty. and repair or
NO within standard delivering oil? replace.
level? Gear pump is Disassemble
See Note 1 NO
broken. and repair.
Are LH/RH
operations OK
possible? Hydraulic pump is Disassemble
Disassemble broken. and repair.
YES main relief valve
Remove dust plug and check if it is
under engine not irregular.
OK flywheel and
Main relief valveDisassemble
Faulty
check if coupling is defective. and repair or
element particles replace.
Inspect oil are not present. Coupling at pump Disassemble
Particles present
NO
volume in
hydraulic oil tank. connection is and repair.
broken.
Short Replenish
hydraulic oil.
YES
Cylinder interior is Disassemble
Does control broken. and repair.
ͽ valve spool
move?
MCV spool is Disassemble
See Note 5, 6 NO
stuck. and repair.
6-18
2) BOOM, ARM OR BUCKET SPEED IS LOW
Cause Remedy
YES
Normal.
YES
Are other ͽ
YES attachment
Is combination speeds within
Is speed low only of oil streams standard levels? NO ;
in composite YES
normal at boom YES
operation? up and at arm Does spool of flow Flow summation Disassemble
extrusion? summation check check valve is and repair.
NO valve move lightly stuck.
Are LH/RH travel by hand?
NO speeds within NO
standard levels?
YES
Hydraulic pump is Disassemble
Are both LH/RH faulty. and repair.
travel speeds YES Ϳ
NO
low? Is MCV pilot
pressure within
NO
standard?
NO
See Note 3, 4
OK
Does the Port relief valve is Disassemble
symptom change faulty. and repair or
YES
when port relief
valve is replaced replace.
Does control with other valve? Cylinder is faulty. Disassemble
YES valve spool NO
and repair.
move ?
See Note 7
NO MCV spool is Disassemble
Is MCV pilot
ͽ pressure within stuck. and repair.
standard level?
Is not MCV pilot YES
Clean pilot
See Note 3, 4
pressure piping piping interior or
clogged or is not
NO
there oil repair piping.
leakage? RCV is defective. Disassemble
NO
and repair.
YES
Pilot relief valve is Disassemble
Is pilot pressure NO faulty. and repair or
; Is gear pump
within standard
delivering oil? replace.
level?
NO
Gear pump is Disassemble
See Note 1
broken. and repair.
AIs engine NO
Ϳ revolution within Adjust engine
standard level? revolution.
YES
Clean orifice in
control valve.
Is not orifice in
main control YES
valve clogged? Is pilot piping Clean pilot
clogged or is oil piping interior or
NO leaking from the repair piping.
piping? Is RCV normal? RCV is faulty. Disassemble
NO NO
and repair.
6-19
3) BOOM, ARM OR BUCKET CYLINDER EXTENDS OR CONTRACTS ITSELF AND ATTACHMENT FALLS
Cause Remedy
YES
Port relief valve is Disassemble
Does the symptom faulty. and repair or
change when port
Normal
relief valve is replace.
YES ͽ
replaced with
normal value? Is control valve
return spring
YES
Is not hydraulic NO
normal?
oil temperature Control valve's Disassemble
high? NO
return spring is and replace.
faulty.
Is genuine Abnormally high. Locate the
hydraulic oil or cause of
equivalent being hydraulic oil
used?
temperature rise
and lower it to
proper level.
Replace with
NO
genuine
hydraulic oil or
equivalent.
OK
Pressure Disassemble
Disassemble and tightness and repair.
inspect load between control
YES
check valve in
MCV and check valve casing and
for any fault. spool is poor.
Is cylinder Contact surface Disassemble
internal leakage Abnormal
ͽ between poppet and repair.
within standard
level? and seat is poor.
6-20
4) BOOM, ARM OR BUCKET POWER IS WEAK
Cause Remedy
YES
Check according
Is cylinder to the procedure
YES internal leakage in Item "Speed is
within standard low".
level?
Is relief pressure
YES in port relief Cylinder is faulty. Disassemble
valve within NO
and repair.
standard level?
Is relief pressure
in main relief Port relief valve is Adjust pressure,
valve within NO
standard level? faulty. repair or replace.
See Note 7
Main relief valve Adjust pressure,
NO
is defective. repair or replace.
Cause Remedy
YES
Port relief valve is Disassemble
Does the defective. and repair or
YES
symptom change
when port relief replace.
YES
valve is replaced Cylinder interior is Disassemble
with other valve? Does control broken. and repair.
valve spool
Is MCV pilot NO move?
YES
pressure within MCV spool is Disassemble
standard level? See Note 5 NO
stuck. and repair.
See Note 4
6-21
6) BOOM MAKES A SQUEAKING NOISE WHEN BOOM IS OPERATED
Cause Remedy
YES
Frictional noise
occurs between
the sliding faces
of boom
cylinder's oil
Is boom foot pin seal and boom
greased proper.
sufficiently?
ö Frictional
noise will
disappear if
they are kept
used.
6-22
ö HOW TO CHECK INTERNAL BOOM CYLINDER LEAKAGE
1. Lower the bucket teeth to the ground with
bucket cylinder fully retracted and arm
cylinder rod retracted almost in full.
14096TS01
(210-7) 6-20(2)
6-23
GROUP 3 ELECTRICAL SYSTEM (CLUSTER TYPE 1)
1. WHEN STARTING SWITCH IS TURNED ON, MONITOR PANEL DISPLAY DOES NOT APPEAR
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No.7 and 8 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective cluster Replace
Check voltage
YES 20~32V
NO 0V
FUSE
CLUSTER NO.7
POWER(24V) 1 6
FUSE
POWER IG(24V) 5 5
NO.8
GND 3 4
CN-56 CN-5
1409S6ES01
6-24
2. COMMUNICATION ERROR FLASHES ON THE CLUSTER (HCESPN 840, FMI 2)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective cluster Replace
Starting switch : ON
Voltage : 2V Defective MCU Replace
NO Disconnection in Repair or replace
wiring harness or (after clean)
poor contact
between CN-5 (1,
2)- CN-51(23, 33)
Check voltage
YES 2V
NO 0V
CLUSTER
GND 3 4 MCU
RS485 RX 8 2 23 RS485 TX
RS485 TX 4 1 33 RS485 RX
CN-51
CN-56 CN-5
1409S6ES02
6-25
3. BATTERY CHARGING WARNING LAMP LIGHTS UP (Starting switch : ON)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective MCU Replace
YES Check voltage
between CN-52
(27) and chassis Disconnection in Repair or replace
NO wiring harness or (after clean)
YES Check voltage Voltage : 20~32V
between CN-3 poor contact
(3) and chassis between CN-52
(27)-CN-3 (3)
Voltage : 20~32V
Check voltage Disconnection in Repair or replace
NO wiring harness or (after clean)
between alternator poor contact
terminal "L" and between CN-3 (3)
chassis alternator terminal
Engine : Running "L"
Voltage : 20~32V
Check voltage
YES 20~32V
NO 0V
ALTERNATOR
MCU B+
G
1 P
27 3 2 L 3~
3 FI U
4 NC
CN-74
CN-52 CN-3
1409S6ES03
6-26
4. WHEN COOLANT OVERHEAT WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Coolant overheat Check engine
Resistance
YES between CD-8 (110˚C Ü2˚C ) cooling system
(1,2) is in range
of 120~150̫?
Defective temp Replace
Disconnect CD-8 NO
Does display go sensor
off when
disconnect CD-8?
YES
Starting switch : ON Resistance Short circuit in Repair or replace
Engine : Start between CN-51 wiring harness (after clean)
NO (13) & CN-52
(25) is 0~1̫?
Defective MCU Replace
Disconnect CN-51 NO
KEY OFF
Check Table
Temperature (˚C ) 0 25 50 80 95
Resistance (k̫) 30~37 9.3~10.7 3.2~3.8 1.0~1.3 0.7~0.8
CN-51
13
MCU
WATER TEMP SENDER
5 1 C
25 6 2
CN-3 CD-8
CN-52 1409S6ES04
6-27
5. WHEN AIR CLEANER WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Clogged air filter or Check filter or
defective switch replace switch
Does display go
off when
disconnect YES
CD-10? Short circuit in Repair or replace
Starting switch : ON wiring harness (after clean)
Engine : Start Check resistance
between CD-10-
between CN-51
NO CN-51 (29)
(29) and chassis
Starting switch : OFF
Disconnect CN-51
Defective MCU Replace
NO
Check resistance
YES MAX 1̫
NO MIN 1M̫
Pa
29
CD-10
CN-51
1409S6ES05
6-28
6. WHEN ENGINE OIL PRESSURE WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Engine oil leakage, Check engine oil
or defective switch level or replace
Does display go off switch
when disconnect
YES
CD-18? Defective controller Replace
Starting switch : ON Check resistance
Engine : Start between CN-51
NO
(27) and chassis
Starting switch : OFF
Disconnection in Repair or replace
NO
Disconnect CN-51 wiring harness or (after clean)
poor contact
between
CN-51 (27)-CD-18
Check resistance
YES MAX 1̫
NO MIN 1M̫
27 1 Pa
1409S6ES06
6-29
7. WHEN HYDRAULIC OIL TEMPERATURE WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
High temperature Check hydraulic
Resistance oil temperature
YES between CD-1 (105˚CÜ2˚C),
(1, 2) is in range
of 164~151̫?
Does display go Starting switch : ON Defective temp Replace
Disconnect CD-1 NO
off when sensor
disconnect
CD-1? YES
Short circuit Repair or replace
Starting switch : ON Resistance between temp
Engine : Start between CN-51
sensor and MCU
NO (13) & CN-52
(24) is 0~1̫?
Defective MCU Replace
Starting switch : OFF NO
Disconnect CN-51
Check Table
Temperature (˚C ) ~ -30 ~ -10 ~0 ~ 40 ~ 70 ~ 80 ~ 90 ~ 100 105~
22.22 8.16 5.18 1.06 0.39 0.322 0.243 0.185 0.164
Resistance (k̫)
~31.78 ~10.74 ~ 6.6 ~1.28 ~0.476 ~0.298 ~0.219 ~0.167 0.151
CN-52
24
MCU
HYDRAULIC OIL
TEMPERATURE SENDER
2 C
13 1
CD-1
CN-51
1409S6ES07
6-30
8. WHEN COOLANT TEMPERATURE GAUGE DOES NOT OPERATE (HCESPN 304,
FMI 3 or 4)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Disconnection in Repair or replace
wiring harness or (after clean)
Is resistance poor contact
YES between CN-51
between
(13) and CN-52
CN-51-CD-8
(25) over 2k̫?
Starting switch : OFF YES
Disconnect CN-50 Defective MCU Replace
Does the gauge
Check resistance
light up and
between CN-3(5)
down at lamp NO
and (6)
check? Defective temp Replace
NO
Starting switch : ON See Table
sensor CD-8
Check Table
Temperature (˚C ) 0 25 50 80 95
Resistance (k̫) 30~37 9.3~10.7 3.2~3.8 1.0~1.3 0.7~0.8
CN-51
13
MCU
WATER TEMP SENDER
5 1 C
25 6 2
CN-3 CD-8
CN-52
1409S6ES04
6-31
9. WHEN FUEL GAUGE DOES NOT OPERATE (HCESPN 301, FMI 3 or 4)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective MCU or Replace
Check resistance cluster
YES between CN-51
(13) and CN-52
(26)
Starting switch : OFF Disconnection in Repair or replace
Check resistance Disconnect CN-51 NO
between fuel Spec : 50~600̫ wiring harness or
See table
sender (1) and poor contact
(2) between fuel
Starting switch : OFF sender-MCU
Spec : 50~600̫
See table
Defective fuel Replace
NO
sender
Check Table
Range Resistance (̫) Range Resistance (̫)
Full 50 5/12 400
11/12 100 4/12 450
10/12 150 3/12 500
9/12 200 2/12 550
8/12 250 1/12 600
7/12 300 Empty warning 700
6/12 350 - -
CN-52
26
MCU
FUEL LEVEL SENDER
13 1
CD-2
CN-51
1409S6ES09
6-32
10. WHEN SAFETY SOLENOID DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and
fuse No.23 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Hydraulic system Check hydraulic
YES Check operation malfunction system
of solenoid
Defective solenoid Replace
NO
Safety lever : ON-OFF
YES
Disconnect in Repair or replace
Check voltage wiring harness or (after clean)
between CN-68 poor contact
Check resistance
(1) - (2) YES between CN-4 between
(16) and chassis CN-4-CN-68
Starting switch : ON
Voltage : 20~30V YES
Safety state Starting switch : OFF Disconnect in Repair or replace
Safety state
Spec : 0̫
wiring harness or (after clean)
Disconnect CN-4 Check resistance poor contact
Check voltage
between CS-4 between
between CN-68 NO
NO (A)-(C) CN-4-CS-4
(2) and chassis
Starting switch : OFF
Safety lever : OFF Defective safety Replace
Safety switch : ON-0̫
Starting switch : ON NO
Voltage : 20~30V
OFF-∞ switch
FUSE
NO.23
SAFETY SWITCH
B C A 14 SAFETY SOLENOID
B 15 2
A C 16 1
CS-4 CN-68
CN-4
21096ES10
6-33
11. WHEN TRAVEL SPEED 1, 2 DOES NOT OPERATE (HCESPN 167, FMI 5 or 6)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No. 25 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Disconnection in Repair or replace
wiring harness or
Check resistance poor contact
YES
between CN-70 between CN-70-
(1) and (2) CN-52
Starting switch : OFF Defective solenoid Replace
Spec : 30̫ NO
YES Check fault code Disconnect CN-70
167 active?
YES
Defective hydraulic Check hydraulic
Starting switch : ON
system system
Check voltage
Check if travel between CN-70
speed lamps( , NO (1) and (2)
) change when
pressing the travel Starting switch : ON Disconnection in Repair or replace
Spec : 20~30 V NO
speed switch on wiring harness or
Disconnect CN-70
the cluster poor contact
Starting switch : ON
between CN-70-
fuse No. 28
YES
Defective cluster Replace
Check MCU
Y R G
NO
Defective MCU Replace
Starting switch : ON
NO
FUSE
MCU NO.28
TRAVEL SOLENOID
3 1
CN-70
CN-52
1409S6ES11
6-34
12. WHEN ENGINE DOES NOT START ( lights up condition)
ÂCheck supply of the power at engine stop solenoid while starting switch is ON.
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No. 1, 4, 13 and 20 burnt out.
START KEY SW
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CN-5
CS-2
H0 I
35 1
0, I
36 2
Cause Remedy 59 3 4
H
YES 60
BR ACC
4 1
B
2
Defective battery Replace 5 3
ST C
5
6
NO.1 CR-35
Check operation YES
Check voltage Defective magnet Replace
of start motor YES between starter of start motor
NO.13
6-35
13. WHEN STARTING SWITCH ON DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted, master
switch ON and check open circuit of fusible link (CN-60). START KEY SW
CN-5
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CS-2
H0 I
35 1
0, I
36 2
59 3 4
H
60
BR ACC
4 1
B
2
5 3
Cause Remedy 6
YES
ST C
5
Disconnection in Repair or replace 6
1409S6ES13
6-36
14. WHEN STARTING SWITCH IS TURNED ON, WIPER MOTOR DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse No. 6,
11 and 17 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CN-21
3 1
Cause Remedy 2
5 3 CN-5
NO
Defective wiper Replace 4 4
cut switch 5
NO 6 M 2 6
Short circuit in Repair or replace
Check operation wiring harness or (after clean)
wiper cut switch WIPER MOTOR FUSE
poor contact 18
between CN-141 NO.6
Front sliding door (11)- CS-53 CN-141 19
open-close
Check valtage
FEED BACK 1
between CN-141 YES
YES (11) and chassis Defective switch Replace MOTOR DRIVE SIG 2 CN-17
panel
NO Check voltage
MOTOR DRIVE- 3 1
Front sliding door-close between CN-116 MOTOR DRIVE+ 4 2
Voltage : 4~5V (10) and chassis GND 5 3
Check operation 1)Recheck fuse Replace FUSE
NO VCC 6 4 24
Starting switch : ON No.11
YES of switch panel Vottage : 20~30V CONTINUE 24V 7 5 NO.17
LED ON. 2)Disconnection in Repair or replace CN-22
wiring harness or (after clean) WASHER P/P 8 6
Starting switch : ON ͽ 2 M
Push wiper switch button YES
poor contact WASHER SIG. 9 7
between INT. SIG 10 8 1
CN-116(10)-Fuse WIPER CUT SW 11 WASHER PUMP
N.C 12
Check voltage between NO FEED BACK 13
Defective switch Replace
CN-116 (4) and chassis panel WIPER MOTOR CONTROLLER
Intermittent
NO 1) Recheck fuse Replace
Check voltage CN-116 CS-53
ͽ No.6
(5) and chassis 2) Disconnection Repair or replace
Washing Check operation in wiring harness (after clean)
of wiper motor or poor contact
Check voltage CN-116 and controller between
(3) and chassis check voltage CN-141(7)-Fuse, WIPER CUT SW
YES CN-141 (7) and
Sarting switch : ON
CN-21(4)-Fuse
Voltage : 0~1V
chassis, CN-21 CN-116
(4) and chassis NO
1) Recheck fuse Replace HEAD LIGHT OUT 1
Starting switch : OFF No.17 WORK LIGHT OUT 2
Voltage : 20~30V Check voltage 2) Disconnection Repair or replace INT. SIG 3
CN-141 (6) and CN-141(6)-Fuse (after clean) WIPER MOTOR DRIVE 4
YES chassis
WASHER SIG 5
; PRE-HEAT 6
Starting switch : ON YES CABIN LIGHT OUT 7
Check continuity Voltage : 20~30V
NO TRAVEL ALARM 8
between Disconnection in Repair or replace NC 9 FUSE
CN-141 (2)-CN-116 (4), wiring harness or (after clean) POWER 24V 10 57
CN-141 (9)-CN-116 (5), poor contact GND 11 NO.11
; CN-141 (10)-CN-116 (3), NC 12
NO
CN-141 (5)-Chassis , Check wiper Defective wiper Replace SWITCH PANEL
CN-141 (1)-CN-21 (5), motor resistance motor
CN-141 (3)-CN-21 (6),
YES between CN-21
CN-141 (4)-CN-21 (2), (2)-CN-21 (6) Defective wiper Replace
CN-141 (13)-CN-21 (3) YES motor controller
Resistance : 3~4̫
21096ES14
6-37
15. WHEN STARTING SWITCH IS TURNED ON, HEAD LAMP DOES NOT LIGHTS UP
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No.18 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
14096ES15
6-38
16. WHEN STARTING SWITCH IS TURNED ON, WORK LAMP DOES NOT LIGHTS UP
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No.15 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective bulb Replace
YES
Check voltage
between CL-5 (1)
and chassis CN-5
FUSE
Disconnection in Repair or replace
NO wiring harness or (after clean) NO.15
poor contact
CN-116
between CR-4
YES Check voltage HEAD LIGHT OUT 1
between CR-4 (87)-CL-5 (2) WORK LIGHT OUT 2
(87) and chassis INT. SIG 3 CR-4
WIPER MOTOR DRIVE 4
Starting switch : ON 30 30 86
WASHER SIG 5
Work lamp switch : ON PRE-HEAT 6 86
Voltage : 20~30V YES
Defective switch Replace CABIN LIGHT OUT 7 87
1
Disconnection in Repair or replace 2
NO
wiring harness or (after clean)
poor contact CL-6
between CR-4
(30) and chassis
or CR-4 (86) and
chassis
21096ES16
6-39
■ ELECTRICAL SYSTEM (CLUSTER TYPE 2)
1. WHEN STARTING SWITCH IS TURNED ON, MONITOR PANEL DISPLAY DOES NOT
APPEAR
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and
fuse No. 8 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective cluster Replace
YES Check voltage
between CN-56A
(1) and chassis Disconnection in Repair or
NO
wiring harness or replace
Check voltage
between CN-5 poor contact (after clean)
(5) and chassis between CN-5(5)
Starting switch : ON
-CN-56A(1)
Voltage : 20~32V
NO Disconnection in Repair or
wiring harness or replace
poor contact (after clean)
between
CN-5(5) and fuse
No.8
Check voltage
YES 20 ~ 32V
NO 0V
CLUSTER
FUSE
POWER IG(24V) 1 5
NO.8
GND 2 4
RX
TX
CN-56A CN-5
1409S6ES51
6-40
2. COMMUNICATION ERROR FLASHES ON THE CLUSTER
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective MCU Replace
KEY ON
Disconnection in Repair or replace
NO
wiring harness or (after clean)
poor contact
between CN-5
(1,2)-CN-50
(29,30)
Check voltage
YES *4V *12V
NO 0V 0V
CLUSTER MCU
POWER IG(24V)
GND 2 4
*12V
RX 3 2 29
*4V
TX 4 1 30
CN-56A CN-5 CN-50
1409S6ES52
6-41
3. BATTERY CHARGING WARNING LAMP LIGHTS UP (starting switch : ON)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective MCU Replace
YES Check voltage
between CN-51
(9) and chassis Disconnection in Repair or replace
NO wiring harness or (after clean)
YES Check voltage Voltage : 20~32V
between CN-3 poor contact
(3) and chassis between CN-51
(9)-CN-3 (3)
Voltage : 20~32V
Check voltage Disconnection in Repair or replace
NO wiring harness or (after clean)
between alternator poor contact
terminal "L" and between CN-2 (3)
chassis alternator terminal
Engine : Running "L"
Voltage : 20~32V
Check voltage
YES 20~32V
NO 0V
ALTERNATOR
MCU B+
G
1 P
9 3 2 L 3~
3 FI U
4 NC
CN-74
CN-51 CN-3
1409S6ES53
6-42
4. WHEN COOLANT OVERHEAT WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Coolant overheat Check engine
Resistance
YES between CD-8 (110˚CÜ2˚C) cooling system
(1,2) is in range
of 120~150̫?
Defective temp Replace
Disconnect CD-8 NO
sensor
Does display go
off when
disconnect CD-8?
YES
Starting switch : ON Short circuit in Repair or replace
Resistance wiring harness (after clean)
Engine : Start
between CN-51
NO (31,33) is
0~1̫? Defective MCU Replace
Disconnect CN-51 NO
KEY OFF
12th step
Check Table
Range 1st step 2nd~10th step 11th~12th step
Temperature ~29˚C 30~105˚C 105˚C ~
1 st step
MCU
WATER TEMP SENDER
31 5 1 C
33 6 2
CN-3 CD-8
CN-51
1409S6ES54
6-43
5. WHEN AIR CLEANER WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Clogged air filter or Check filter or
defective switch replace switch
Does display go
off when
disconnect YES
CD-10? Short circuit in Repair or replace
Starting switch : ON
wiring harness (after clean)
Engine : Start Check resistance between
between CN-51 CD-10-CN-51(16)
NO
(16) and chassis
Starting switch : OFF
Defective MCU Replace
NO
Disconnect CN-51
Check resistance
YES MAX 1̫
NO MIN 1M̫
Pa
16
CD-10
CN-51
1409S6ES55
6-44
6. WHEN ENGINE OIL PRESSURE WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Engine oil leakage, Check engine oil
or defective switch level or replace
Does display go switch
off when
disconnect
CD-18? YES
Starting switch : ON Defective controller Replace
Engine : Start Check resistance
between CN-51
NO
(4) and chassis
Starting switch : OFF Defective MCU Repair or replace
NO
Disconnect CN-51 (after clean)
Check resistance
YES MAX 1̫
NO MIN 1M̫
4 1 Pa
1409S6ES56
6-45
7. WHEN HYDRAULIC OIL TEMPERATURE WARNING LAMP LIGHTS UP (engine is started)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
High temperature Check hydraulic
Resistance oil temperature
YES between CD-1 (100˚CÜ2˚C)
(1,2) is in range and replace
of 130~150̫?
Does display go Starting switch : ON Defective temp Replace
Disconnect CD-1 NO
off when sensor
disconnect
YES
CD-1? Short circuit Check and repair
Starting switch : ON between temp
Engine : Start
Resistance
between CN-51 sensor and MCU
NO (31,34) is 0~1̫?
34 2 C
31 1
CD-1
CN-51
1409S6ES57
6-46
8. WHEN COOLANT TEMPERATURE GAUGE DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Disconnection in Repair or replace
wiring harness or (after clean)
Is resistance poor contact
YES between CN-51
between
(31) and (33)
CN-51-CD-8
over 2k̫?
Starting switch : OFF YES
Disconnect CN-50 Defective MCU Replace
Does the gauge
Check resistance
light up and
between CN-3(5)
down at lamp NO
and (6)
check? Defective temp Replace
See Table NO
Starting switch : ON sensor CD-8
12th step
Check Table
Range 1st step 2nd~10th step 11th~12th step
Temperature ~29ÁC 30~105ÁC 105ÁC ~
1 st step
MCU
WATER TEMP SENDER
31 5 1 C
33 6 2
CN-3 CD-8
CN-51
1409S6ES54
6-47
9. WHEN FUEL GAUGE DOES NOT OPERATE (check warning lamp ON/OFF)
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Disconnection in Check and repair
wiring harness
Is resistance
YES between CN-51
(24) and (31)
over 1k̫? YES
Defective Replace
Starting switch : OFF
Disconnect CN-51
Check resistance controller
Does the gauge between CD-2(1)
light up and NO and (2)
down at lamp Replace
Disconnect CD-2 NO
check? Defective fuel
See Table
Starting switch : ON sensor
2nd~10th step
Check Table
1 st step 11th~12th
step
Range 1st step 2nd~10th step 11th~12th step
Item
Unit Resistance(̫) 700~601 600~101 ~100
Tolerance(%) Ü5 Ü5 Ü5
MCU
FUEL LEVEL SENDER
24 2
31 1
CD-2
CN-51
1409S6ES59
6-48
10. WHEN SAFETY SOLENOID DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and
fuse No.23 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Hydraulic system Check hydraulic
YES Check operation malfunction system
of solenoid
Defective solenoid Replace
NO
Safety lever : ON-OFF
YES
Disconnect in Repair or replace
Check voltage wiring harness or (after clean)
between CN-68 poor contact
Check resistance
(1) - (2) YES between CN-4 between
(16) and chassis CN-4-CN-68
Starting switch : ON
Voltage : 20~30V YES
Safety state Starting switch : OFF Disconnect in Repair or replace
Safety state
Spec : 0̫
wiring harness or (after clean)
Disconnect CN-4 Check resistance poor contact
Check voltage
between CS-4 between
between CN-68 NO
NO (A)-(C) CN-4-CS-4
(2) and chassis
Starting switch : OFF
Safety lever : OFF Defective safety Replace
Safety switch : ON-0̫
Starting switch : ON NO
Voltage : 20~30V
OFF-∞ switch
FUSE
NO.23
SAFETY SWITCH
B C A 14 SAFETY SOLENOID
B 15 2
A C 16 1
CS-4 CN-68
CN-4
21096ES10
6-49
11. WHEN TRAVEL SPEED 1, 2 DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and
short of fuse No. 28.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective hydraulic Check hydraulic
system system
YES Check voltage YES Check operation
between CN-50 YES
of solenoid Defective MCU Replace
(13) and chassis
Check resistance
Check if travel Starting switch : ON Starting switch : ON between CN-70
speed lamps( , Voltage : 20~30V : OFF NO
(1) and (2)
Disconnect CN-50 : ON
) change when
Starting switch : OFF NO Defective solenoid Replace
pressing the travel
SPEC : 15~25̫
speed switch on Disconnect CN-70
the cluster YES
Starting switch : ON Defective cluster Replace
Check controller
Y R G
NO
Defective MCU Replace
Starting switch : ON
NO
FUSE
MCU NO.28
TRAVEL SOLENOID
13 1
CN-70
CN-50
1409S6ES61
6-50
12. WHEN ENGINE DOES NOT START ( lights up condition)
ÂCheck supply of the power at engine stop solenoid while starting switch is ON.
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No. 1, 4, 10 and 13 burnt out.
START KEY SW
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CN-5
CS-2
H0 I
35 1
0, I
36 2
Cause Remedy 59 3 4
H
YES 60
BR ACC
4 1
B
2
Defective battery Replace 5 3
ST C
5
6
NO.1 CR-35
Check operation YES
Check voltage Defective magnet Replace
of start motor YES between starter of start motor
NO.10
6-51
13. WHEN STARTING SWITCH ON DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted, master
switch ON and check open circuit of fusible link (CN-60). START KEY SW
CN-5
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CS-2
H0 I
35 1
0, I
36 2
59 3 4
H
60
BR ACC
4 1
B
2
5 3
Cause Remedy 6
YES
ST C
5
Disconnection in Repair or replace 6
1409S6ES63
6-52
14. WHEN STARTING SWITCH IS TURNED ON, WIPER MOTOR DOES NOT OPERATE
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse No. 6,
11 and 17 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified. CN-21
3 1
Cause Remedy 2
5 3 CN-5
NO
Defective wiper Replace 4 4
cut switch 5
NO 6 M 2 6
Short circuit in Repair or replace
Check operation wiring harness or (after clean)
wiper cut switch WIPER MOTOR FUSE
poor contact 18
between CN-141 NO.6
Front sliding door (11)- CS-53 CN-141 19
open-close
Check valtage
FEED BACK 1
between CN-141 YES
YES (11) and chassis Defective switch Replace MOTOR DRIVE SIG 2 CN-17
panel
NO Check voltage
MOTOR DRIVE- 3 1
Front sliding door-close between CN-116 MOTOR DRIVE+ 4 2
Voltage : 4~5V (10) and chassis GND 5 3
Check operation 1)Recheck fuse Replace FUSE
NO VCC 6 4 24
Starting switch : ON No.11
YES of switch panel Vottage : 20~30V CONTINUE 24V 7 5 NO.17
LED ON. 2)Disconnection in Repair or replace CN-22
wiring harness or (after clean) WASHER P/P 8 6
Starting switch : ON ͽ 2 M
Push wiper switch button YES
poor contact WASHER SIG. 9 7
between INT. SIG 10 8 1
CN-116(10)-Fuse WIPER CUT SW 11 WASHER PUMP
N.C 12
Check voltage between NO FEED BACK 13
Defective switch Replace
CN-116 (4) and chassis panel WIPER MOTOR CONTROLLER
Intermittent
NO 1) Recheck fuse Replace
Check voltage CN-116 CS-53
ͽ No.6
(5) and chassis 2) Disconnection Repair or replace
Washing Check operation in wiring harness (after clean)
of wiper motor or poor contact
Check voltage CN-116 and controller between
(3) and chassis check voltage CN-141(7)-Fuse, WIPER CUT SW
YES CN-141 (7) and
Sarting switch : ON
CN-21(4)-Fuse
Voltage : 0~1V
chassis, CN-21 CN-116
(4) and chassis NO
1) Recheck fuse Replace HEAD LIGHT OUT 1
Starting switch : OFF No.17 WORK LIGHT OUT 2
Voltage : 20~30V Check voltage 2) Disconnection Repair or replace INT. SIG 3
CN-141 (6) and CN-141(6)-Fuse (after clean) WIPER MOTOR DRIVE 4
YES chassis
WASHER SIG 5
; PRE-HEAT 6
Starting switch : ON YES CABIN LIGHT OUT 7
Check continuity Voltage : 20~30V
NO TRAVEL ALARM 8
between Disconnection in Repair or replace NC 9 FUSE
CN-141 (2)-CN-116 (4), wiring harness or (after clean) POWER 24V 10 57
CN-141 (9)-CN-116 (5), poor contact GND 11 NO.11
; CN-141 (10)-CN-116 (3), NC 12
NO
CN-141 (5)-Chassis , Check wiper Defective wiper Replace SWITCH PANEL
CN-141 (1)-CN-21 (5), motor resistance motor
CN-141 (3)-CN-21 (6),
YES between CN-21
CN-141 (4)-CN-21 (2), (2)-CN-21 (6) Defective wiper Replace
CN-141 (13)-CN-21 (3) YES motor controller
Resistance : 3~4̫
21096ES14
6-53
15. WHEN STARTING SWITCH IS TURNED ON, HEAD LAMP DOES NOT LIGHTS UP
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No.18 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
14096ES15
6-54
16. WHEN STARTING SWITCH IS TURNED ON, WORK LAMP DOES NOT LIGHTS UP
ÂBefore disconnecting the connector, always turn the starting switch OFF.
ÂBefore carrying out below procedure, check all the related connectors are properly inserted and fuse
No.15 burnt out.
ÂAfter checking, insert the disconnected connectors again immediately unless otherwise specified.
Cause Remedy
YES
Defective bulb Replace
YES
Check voltage
between CL-5 (1)
and chassis CN-5
FUSE
Disconnection in Repair or replace
NO wiring harness or (after clean) NO.15
poor contact
CN-116
between CR-4
YES Check voltage HEAD LIGHT OUT 1
between CR-4 (87)-CL-5 (2) WORK LIGHT OUT 2
(87) and chassis INT. SIG 3 CR-4
WIPER MOTOR DRIVE 4
Starting switch : ON 30 30 86
WASHER SIG 5
Work lamp switch : ON PRE-HEAT 6 86
Voltage : 20~30V YES
Defective switch Replace CABIN LIGHT OUT 7 87
1
Disconnection in Repair or replace 2
NO
wiring harness or (after clean)
poor contact CL-6
between CR-4
(30) and chassis
or CR-4 (86) and
chassis
21096ES16
6-55
GROUP 4 MECHATRONICS SYSTEM (CLUSTER TYPE 1)
Cause Remedy
YES
Defective
YES Check pressure hydraulic system
at EPPR valve
NO Check electric Defective Replace
current at EPPR SPEC : 5~20 kgf/cm2
NO
EPPR valve
valve See TEST 3
SPEC : 100~700 mA
See TEST 2
Defective MCU Replace
Check if HCESPN NO
140 active fault
display on the LCD YES
Short circuit or Check & repair
poor connection wire harness or
between CN-52 between CN-52
Check resistance
YES at EPPR valve -CN-75 -CN-75
Wiring diagram
MCU
FUSE
8
NO.10
9
19 2
CN-52 CN-75
1409S6MS01
6-56
2) TEST PROCEDURE SPEC : 15~25̫(20˚C)
(1) Test 1 : Check resistance at connector
CN-75 EPPR valve
CN-75.
Η Starting key OFF.
Θ Disconnect connector CN-75 from EPPR
valve at main hydraulic pump. Multimeter
Ι Check resistance between 2 lines as Valve casing
figure.
Main pump
14096MS33
14095MS21
(3) Test 3 : Check pressure at EPPR valve. Spec : 2~25 kgf/cm2 (30~350 psi)
Η Remove plug and connect pressure
gauge as figure. Pressure adjusting Pilot pressure
screw locknut supply line
ÂGauge capacity : 0 to 50 kgf/cm2
EPPR valve
(0 to 710 psi) CN-75
Θ Start engine.
Ι Set S-mode and cancel auto decel
mode.
Valve casing
Κ Position the accel dial at 10.
Λ If rpm display approx 2050Ü50 rpm check
pressure at relief position of bucket circuit
by operating bucket control lever.
Μ If pressure is not correct, adjust it. Main pump
Ν After adjust, test the machine.
14095MS22
6-57
2. ENGINE STALL
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Not enough Check engine
engine power fault
YES Check pressure Contact cummins
at EPPR valve
SPEC : 15~25̫(20˚C)
See TEST 1
NO
Defective EPPR Replace
valve
Wiring diagram
MCU
FUSE
8
NO.10
9
19 2
CN-52 CN-75
1409S6MS01
6-58
2) TEST PROCEDURE SPEC : 100~700 mA
(1) Te
Test
st 4 : Check electric current at EPPR Adapter(P/no.:21Q6-50410)
valve. EPPR valve
Η Disconnect connector CN-75 from Multimeter
CN-75
EPPR valve.
Θ Insert the adapter to CN-75 and install
multimeter as figure.
Valve casing
Ι Start engine.
Κ Set S-mode and cancel auto decel
mode.
Λ Position the accel dial at 10.
Μ If rpm display approx 2050Ü50 rpm Main pump
check electric current at bucket circuit
relief position. 14095MS21
(2) Test 5 : Check pressure at EPPR valve. SPEC : 2~25 kgf/cm2 (30~350 psi)
Η Remove plug and connect pressure Pressure adjusting Pilot pressure
gauge as figure. screw locknut supply line
6-59
3. MALFUNCTION OF CLUSTER OR MODE SELECTION SYSTEM
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
No power supply to Check fuse No.3
See if all lamps the MCU
YES off in the MCU
case YES
Y R G MCU failure Replace
Y R G
See if HCESPN
840 active fault NO
display on the LCD
NO Y R G
ͽ
NO
OK
Check connection Cluster failure Replace
between CN-51
ͽ (33) - CN-56(4) or
CN-51(23) -
CN-56(8) No connection Check and repair
NO
KEY OFF
Wiring diagram
CLUSTER
MCU
BATT.24V
SIG_3
GND
TX 4 1 33
IG 24V 8 2 23
SIG_2
CN-56 CN-5 1
CAMERA SIG
RX CN-51
FUSE
NO.3
1409S6MS03
6-60
4. MALFUNCTION OF ACCEL DIAL
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
YES
Open circuit or Replace or repair
poor connection
between CN-7
(15) -CN-52 (23)
Check voltage
between YES Check voltage
CN-52(23)-GND between
CN-7(15)-GND
Spec : actuator operating
1~5V Spec : actuator operating
1~5V YES
See TEST 6 Check resistance Defective accel Replace
between dial
NO CN-142(B)- CN-52
Check voltage CN-7(15) Open circuit or Replace or repair
NO
between Spec : 0̫ poor connection
NO between CN-142 23
CN142(A)-(C)
(B) -CN-7 (15)
Spec : 5V
YES
Open circuit or Replace or repair
poor connection MCU
between CN-142
Check voltage ACCEL DIAL
(A) -CN-7 (14) or
between
NO CN-7(14)-(16) CN-142 (C )- + A 14 6
CN-7 (16)
S B 15 5
Spec : 5V
Open circuit or Replace or repair - C 16
NO
poor connection CN-142
between CN-7 CN-7 CN-51
(14) -CN-51 (6) or
CN-7 (16) -
CN-51 (5)
1409S6MS04
6-61
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 6 : Check voltage at CN-52(23) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
MCU
copper. PIN
Θ Insert prepared pin to rear side of CN-51 CN-52
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
23
30
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS04A
6-62
5. AUTO DECEL SYSTEM DOES NOT WORK
· Fault code : HCESPN 105, FMI 0~4 (work pressure sensor)
HCESPN 108, FMI 0~4 (travel oil pressure sensor)
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
YES
Defective travel Replace
Check voltage
NO pressure switch
between CD-6(A)
and (C)
Short circuit or poor Replace or repair
NO
Check voltage SPEC : connection
between CN-52 Key ON : 24±2V between CN-51(3)-
(38)-GND and CD-6(A) and / or
CN-52(37)-GND CN-51(13)-CD-6(C)
(fault code 108
SPEC :
Actuator operating : 1~5V
displayed)
See TEST 7, 8 YES
Defective work Replace
Check voltage
pressure sensor
between CD-7(A)
NO and (C)
Short circuit or poor Replace or repair
NO
SPEC : connection
Key ON : 24±2V between CN-51(3)-
CD-7(A) and / or
CN-51(13)-CD-7(C)
(fault code 105
displayed)
Wiring diagram
CN-51
CD-6
3 A SUPPLY
B SIG
13 C RETURN
TRAVEL PRESSURE SENSOR
MCU
38 CD-7
A SUPPLY
37 B SIG
C RETURN
CN-52 WORK PRESSURE SENSOR
1409S6MS05
6-63
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 7 : Check voltage at CN-52(38) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
MCU
copper. PIN
Θ Insert prepared pin to rear side of CN-51 CN-52
Multimeter
10 9 8 7 6 5 4 3 2 1
CN-52
20 11 Female
30 21
37
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS05A
6-64
6. MALFUNCTION OF PUMP 1 PRESSURE SENSOR
· Fault code : HCESPN 120, FMI 0~4
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Wiring diagram
CN-51
CD-42
3 A SUPPLY
B SIG
13 C RETURN
PUMP 1 PRESSURE SENSOR
MCU
29
CN-52
1409S6MS06
6-65
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 12 : Check voltage at CN-52(29) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
PIN
Θ Insert prepared pin to rear side of
CN-51 CN-52
connectors : One pin to (29) of CN-52.
Ι Starting key ON.
Κ Check voltage as figure.
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
29
30
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS06A
6-66
7. MALFUNCTION OF PUMP 2 PRESSURE SENSOR
· Fault code : HCESPN 121, FMI 0~4
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Wiring diagram
CN-51
CD-43
3 A SUPPLY
B SIG
13 C RETURN
PUMP 2 PRESSURE SENSOR
MCU
30
CN-52
1409S6MS07
6-67
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 10 : Check voltage at CN-52(30) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
PIN
Θ Insert prepared pin to rear side of
CN-51 CN-52
connectors : One pin to (30) of CN-52.
Ι Starting key ON.
Κ Check voltage as figure.
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
30
30
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS07A
6-68
8. MALFUNCTION OF PUMP 3 PRESSURE SENSOR
· Fault code : HCESPN 125, FMI 0~4
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
YES
Short circuit or poor Replace or repair
connection
YES Check voltage between CN-52-
between
CN-2(4)-GND (32)-CN-2(4)
Check voltage SPEC : Detective P3 Replace or repair
between CN-52 Actuator operating: 1~5V NO
Check voltage pressure sensor
(32) - GND YES between Short circuit or poor Replace or repair
SPEC : CD-44(A)-(C) connection
Actuator operating: 1~5V between CN-2(4)-
See TEST 11 SPEC :
Key ON : 24±2V CD-44(B)
Wiring diagram
CN-51
CD-44
3 13 A SUPPLY
4 B SIG
13 15 C RETURN
PUMP 3 PRESSURE SENSOR
CN-2
MCU
32
CN-52
1409S6MS08
6-69
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 11 : Check voltage at CN-52(32) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
Θ Insert prepared pin to rear side of PIN
CN-51 CN-52
connectors : One pin to (32) of CN-52.
Ι Starting key ON.
Κ Check voltage as figure.
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
30
32
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS08A
6-70
9. MALFUNCTION OF SWING PRESSURE SENSOR
· Fault code : HCESPN 135, FMI 0~4
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Wiring diagram
CN-51
CD-24
3 A SUPPLY
B SIG
13 C RETURN
SWING PRESSURE SENSOR
MCU
36
CN-52
1409S6MS11
6-71
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 14 : Check voltage at CN-52(36) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
Θ Insert prepared pin to rear side of PIN
CN-51 CN-52
connectors : One pin to (36) of CN-52.
Ι Starting key ON.
Κ Check voltage as figure.
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
30
36
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS11A
6-72
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 16 : Check voltage at CN-52(35) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
MCU
copper. PIN
Θ Insert prepared pin to rear side of CN-51 CN-52
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
30
35
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
1409S6MS13A
6-74
11. MALFUNCTION OF POWER MAX
· Fault code : HCESPN 166, FMI 4 or 6
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Short circuit or poor Repair or replace
connection between
YES Check resistance CN-88(1)-CN-52(2)
between CN-88
(1)-(2)
Defective power
NO
YES Check resistance SPEC: 15-35̫ max. solenoid valve Repair or replace
between CN-51 See TEST 18 Check hydraulic
(18)-GND
system
Wiring diagram
MCU
CN-88
2 1
2
CN-52
POWER MAX SOLENOID
18 5
FUSE
6
NO.28
CN-51 CN-4
CS-29
1
2
1409S6MS14
6-75
2) TEST PROCEDURE SPEC : Key ON : 24Ü1V
Key OFF : 0V
(1) Test 17:
17 Check voltage between connector
CN-88(2) - GND.
Η Disconnect connector CN-88 from power
max solenoid valve. Power max switch
Θ Start key ON.
Ι Check voltage as figure.
LH RCV-lever
CN-88
Power max
solenoid valve
2 1
1 2
GROUND
Multimeter
21096MS14A
LH RCV-lever
CN-88
Power max 2 1
solenoid valve
1 2
Multimeter
21096MS14B
6-76
12. MALFUNCTION OF BOOM PRIORITY EPPR VALVE
· Fault code : HCESPN 141, FMI 5 or 6
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Short circuit or poor Repair or replace
connection between
CN-52(17)-CN-133
Check resistance (1) or CN-52(7)-
between CN-133(2)
CN-133(1)-(2)
SPEC : 20~30V
KEY : ON
Defective EPPR Repair or replace
NO
valve
Wiring diagram
MCU
17
CN-133
7 2
BOOM PRIORITY
EPPR VALVE
CN-52
1409S6MS15
6-77
13. MALFUNCTION OF ARM REGENERATION SOLENOID
· Fault code : HCESPN 170, FMI 4 or 6
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Wiring diagram
MCU
CN-135
1 1
FUSE
NO.28
CN-52
1409S6MS16
6-78
10. MALFUNCTION OF BOOM UP PRESSURE SENSOR
· Fault code : HCESPN 127, FMI 0~4
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Wiring diagram
CN-51
CD-32
3 A SUPPLY
B SIG
13 C RETURN
BOOM UP PRESSURE SENSOR
MCU
35
CN-52
1409S6MS13
6-73
2) TEST PROCEDURE SPEC : Key ON : 24±2 V
(1) Test 19 : Check voltage at CN-52(1) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
Θ Insert prepared pin to rear side of PIN
CN-51 CN-52 CN-53
connectors : One pin to (1) of CN-52.
Ι Starting key ON.
Κ Check voltage as figure.
CN-52 Female
10 9 8 7 6 5 4 3 2 1
20 11
30 21
40 39 38 37 36 35 34 33 32 31
GROUND
Multimeter
21096MS16A
6-79
■ MECHATRONICS SYSTEM (CLUSTER TYPE 2)
Cause Remedy
YES
Defective
YES Check pressure hydraulic system
at EPPR valve
NO Check electric Defective Replace
current at EPPR SPEC : 5~20 kgf/cm2
NO
EPPR valve
valve See TEST 3
SPEC : 100~700 mA
See TEST 2
Defective MCU Replace
Check if HCESPN NO
140 active fault
display on the LCD YES
Short circuit or Check & repair
poor connection wire harness or
between CN-50 between CN-50
Check resistance
YES at EPPR valve -CN-75 -CN-75
Wiring diagram
MCU
FUSE
24
NO.9
8
36 2
CN-50 CN-75
1409S6MS51
6-80
2) TEST PROCEDURE SPEC : 15~25̫(20˚C)
(1) Test 1 : Check resistance at connector
CN-75 EPPR valve
CN-75.
Η Starting key OFF.
Θ Disconnect connector CN-75 from EPPR
valve at main hydraulic pump. Multimeter
Ι Check resistance between 2 lines as Valve casing
figure.
Main pump
14096MS33
14095MS21
(3) Test 3 : Check pressure at EPPR valve. Spec : 2~25 kgf/cm2 (30~350 psi)
Η Remove plug and connect pressure
Pressure adjusting Pilot pressure
gauge as figure. screw locknut supply line
ÂGauge capacity : 0 to 50 kgf/cm2
EPPR valve
(0 to 710 psi) CN-75
Θ Start engine.
Ι Set S-mode and cancel auto decel
mode.
Valve casing
Κ Position the accel dial at 10.
Λ If rpm display approx 2050Ü50 rpm check
pressure at relief position of bucket circuit
by operating bucket control lever.
Μ If pressure is not correct, adjust it. Main pump
Ν After adjust, test the machine.
14095MS22
6-81
2. ENGINE STALL
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Not enough Check engine
engine power fault
YES Check pressure Contact cummins
at EPPR valve
SPEC : 15~25̫(20˚C)
See TEST 1
NO
Defective EPPR Replace
valve
Wiring diagram
MCU
FUSE
24
NO.9
8
36 2
CN-50 CN-75
1409S6MS51
6-82
2) TEST PROCEDURE SPEC : 100~700 mA
(1) Te
Test
st 4 : Check electric current at EPPR Adapter(P/no.:21Q6-50410)
valve. EPPR valve
Η Disconnect connector CN-75 from Multimeter
CN-75
EPPR valve.
Θ Insert the adapter to CN-75 and install
multimeter as figure. Valve casing
Ι Start engine.
Κ Set S-mode and cancel auto decel
mode.
Λ Position the accel dial at 10.
Μ If rpm display approx 2050Ü50 rpm Main pump
check electric current at bucket circuit
relief position. 14095MS21
(2) Test 5 : Check pressure at EPPR valve. SPEC : 2~25 kgf/cm2 (30~350 psi)
Η Remove plug and connect pressure Pressure adjusting Pilot pressure
gauge as figure. screw locknut supply line
6-83
3. MALFUNCTION OF CLUSTER OR MODE SELECTION SYSTEM
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
No power supply to Check fuse
See if all lamps the MCU
YES off in the MCU
case YES
Y R G MCU failure Replace
Y R G
See if Co : Er
current error display NO
on the LCD
NO Y R G
ͽ
NO
OK
Check connection Cluster failure Replace
between CN-50
ͽ (29) - CN-5(2) or
CN-50(30) -
CN-5(1) No connection Check and repair
NO
KEY OFF
Wiring diagram
MCU
CLUSTER
POWER IG(24V)
GND
RX 3 2 29
TX 4 1 30
CN-56A CN-5 7
CN-50
FUSE
NO.3
1409S6MS53
6-84
4. MALFUNCTION OF ACCEL DIAL
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
YES
Open circuit or Replace or repair
poor connection
between CN-7
(15) -CN-51 (23)
Check voltage
between YES Check voltage
CN-51(23)-GND between
CN-7(15)-GND
Spec : actuator operating
1~5V Spec : actuator operating
1~5V YES
See TEST 6 Check resistance Defective accel Replace
between dial
NO CN-142(B)-
Check voltage CN-7(15) Open circuit or Replace or repair
NO
between Spec : 0̫ poor connection
NO between CN-142
CN142(A)-(C)
(B) -CN-7 (15) MCU
Spec : 5V
YES ACCEL DIAL
Open circuit or Replace or repair
poor connection + A 14 21
between CN-142 S B 15 23
Check voltage
(A) -CN-7 (14) or
between - C 16 20
NO CN-7(14)-(16) CN-142 (C )-
CN-7 (16) CN-142
CN-7 CN-51
Spec : 5V
Open circuit or Replace or repair
NO
poor connection
between CN-7
(14) -CN-51 (21)
or CN-7 (16) -
CN-51 (20)
1409S6MS54
6-85
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 6 : Check voltage at CN-51(23) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
copper. MCU
PIN
Θ Insert prepared pin to rear side of
CN-50 CN-51
connectors : One pin to (23) of CN-51.
Ι Starting key ON.
Κ Check voltage as figure.
CN-51 Female
12 1
24 23 13
36 25
GROUND
Multimeter
1409S6MS54A
6-86
5. AUTO DECEL SYSTEM DOES NOT WORK
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
YES
Defective travel Replace
NO Check voltage
pressure switch
between CD-6(A)
and (C)
Short circuit or poor Replace or repair
NO
SPEC : connection
Check voltage between CN-51(7)-
Key ON : 24±2V
between CN-52
CD-6(A) and / or
(8)-GND
CN-51(13)-CD-6(C)
SPEC :
Actuator operating : 1~5V
See TEST 7 YES
Defective work Replace
Check voltage
pressure sensor
between CD-7(A)
NO and (C)
Short circuit or poor Replace or repair
NO
SPEC : connection
Key ON : 24±2V between CN-51(7)-
CD-7(A) and / or
CN-51(1)-CD-7(C)
Wiring diagram
MCU
1 CD-6
7 A SUPPLY
8 B SIG
13 C RETURN
TRAVEL PRESSURE SENSOR
CN-51
CD-7
A SUPPLY
B SIG
C RETURN
WORK PRESSURE SENSOR
1409S6MS55
6-87
2) TEST PROCEDURE SPEC : Actuator operating : 1~5 V
(1) Test 7 : Check voltage at CN-51(8) and
ground.
Η Prepare 1 piece of thin sharp pin, steel or
MCU
copper.
PIN
Θ Insert prepared pin to rear side of CN-50 CN-51
connectors : One pin to (8) of CN-51.
Ι Starting key ON.
Κ Check voltage as figure.
CN-51 Female
12 8 1
24 13
36 25
GROUND
Multimeter
1409s6MS55A
6-88
6. MALFUNCTION OF PUMP 1 PRESSURE SENSOR
ö Before carrying out below procedure, check all the related connectors are properly inserted.
1) INSPECTION PROCEDURE
Cause Remedy
YES
Defective MCU Replace
Check voltage
YES
between CN-52 Detective N1 Replace or repair
(10) - GND pressure sensor
SPEC : Short circuit or Replace or repair
Actuator operating: 1~5V Check voltage poor connection
See TEST 10 between CD-42 between CN-51
NO (A)-(C) (10)-CD-42 (B)
SPEC :
Key ON : 24±2V
Short circuit or Replace or repair
NO