Академический Документы
Профессиональный Документы
Культура Документы
NC-1100 Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1120 Temperature Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1130 Boundaries of Jurisdiction Applicable to This Subsection. . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1131 Boundary of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1132 Boundary Between Components and Attachments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1132.1 Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NC-1132.2 Jurisdictional Boundary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figures
NC-1132.2-1 Attachments in the Component Support Load Path Which do not Perform
a Pressure Retaining Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
NC-1132.2-2 Attachments Which do not Perform a Pressure Retaining Function and Are
not in the Component Support Load Path (Nonstructural Attachments) . . . . . . . . . 6
NC-1132.2-3 Attachments Which Perform a Pressure Retaining Function. . . . . . . . . . . . . . . . . . . . . . 7
1
ARTICLE NC-1000
INTRODUCTION
3
NC-1132.2 1998 SECTION III, DIVISION 1 — NC NC-1132.2
below. Figures NC-1132.2-1 through NC-1132.2-3 are more than 2t from the pressure retaining portion of
provided as an aid in defining the boundary and con- the component, where t is the nominal thickness of
struction requirements of this Subsection. the pressure retaining material. Beyond 2t from the
(a) Attachments cast or forged with the component pressure retaining portion of the component, the first
and weld buildup on the component surface shall be weld shall be considered part of the attachment.
considered part of the component. (e) The first connecting weld of a welded nonstructu-
(b) Attachments, welds, and fasteners having a pres- ral attachment to a component shall be considered part
of the attachment. At or within 2t from the pressure
sure retaining function shall be considered part of the
retaining portion of the component the first connecting
component.
weld shall conform to NC-4330.
(c) Except as provided in (d) and (e) below, the (f) Mechanical fasteners used to connect a nonpres-
boundary between a pressure retaining component and sure-retaining attachment to the component shall be
an attachment not having a pressure retaining function considered part of the attachment.
shall be at the surface of the component. (g) The boundary may be located further from the
(d) The first connecting weld of a nonpressure-re- pressure retaining portion of the component than as
taining structural attachment to a component shall be defined in (a) through (f) above when specified in the
considered part of the component unless the weld is Design Specification.
4
NC-1000 — INTRODUCTION Fig. NC-1132.2-1
5
Fig. NC-1132.2-2 1998 SECTION III, DIVISION 1 — NC
FIG. NC-1132.2-2 ATTACHMENTS WHICH DO NOT PERFORM A PRESSURE RETAINING FUNCTION AND
ARE NOT IN THE COMPONENT SUPPORT LOAD PATH (NONSTRUCTURAL ATTACHMENTS)
6
NC-1000 — INTRODUCTION Fig. NC-1132.2-3