Академический Документы
Профессиональный Документы
Культура Документы
:
00-GA-E-60001
PEDEC
Contractor:
Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
Contractor: PEDEC
Consultant:
Sheet 2 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
MAX MAX
C.A. VALVE
Code Rating Finish PRESS TEMP Service Base mat. des. NOTE
Inch TRIM
barg °C
FW:Firewater, FF:Firefighting
RATING CARBON STEEL-
11R 150 RF 100.00 Foam, SW:Service Water, RW:Raw 3 13 Cr B 31.3
B16.5 NACE
Water
CARBON STEEL-
13C 300 RF 44 180.00 PG: Process Gas 6 Inconel 625 B 31.3
NACE + H.I.C.
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 3 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
CARBON STEEL-
15E 600 RF 85 210.00 PG:Process Gas 6 Inconel 625 B 31.3
NACE + H.I.C.
CARBON STEEL-
15F 600 RF 85 100.00 PG:Process Gas 3 316 SS B 31.3
NACE + H.I.C.
Contractor: PEDEC
Consultant:
Sheet 4 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
CARBON STEEL-
18B 2500 RJ 370 135.00 PG: Process Gas 6 316 SS B 31.3
NACE + H.I.C.
LOW TEMP.
API
19A RJ 590 150.00 PG: Process Gas CARBON ST.(-20)- 6 316 SS B 31.3
1000
NACE + H.I.C.
LOW TEMP.
API PG: Process Gas, PRW: Produced
19B RJ 590 150.00 CARBON ST.(-20)- 3 316 SS B 31.3
1000 Water
NACE + H.I.C.
RATING
31B 150 RF 100.00 OX: Oxygen AISI 316-NACE 0 Monel B 31.3
B16.5
33C 300 RF 15 150.00 GY: Glycol , LF: LP Flare AISI 316L-NACE 0 316 SS B 31.3
RATING
35B 600 RF 100.00 OX: Oxygen AISI 316-NACE 0 Monel B 31.3
B16.5
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 5 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
38A 2500 RJ 255 130.00 PG: Process Gas AISI 316L-NACE 0 316 SS B 31.3
RATING
51A 150 RF 100.00 HF: HP Flare INCONEL 625-NACE 0 Inconel 625 B 31.3
B16.5
RATING
55B 600 RF 100.00 P: Process Fluid, PG: Process Gas INCONEL 625-NACE 0 Inconel 625 B 31.3
B16.5
RATING
56B 900 RJ 100.00 P: Process Fluid INCONEL 625 0 Inconel 625 B 31.3
B16.5
RATING IA: Instrument Air, UA: Plant Air, CARBON STEEL &
91A 150 RF 100.00 0 13 Cr B 31.3
B16.5 CA: Compressed Air GALV. C.S.
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 6 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
POLYETHYLENE-
93R PN 6 FF 6 70.00 OY: Open Drain 0 B 31.3
HD
RF = Raised Face
FF = Flat Face
RJ = Ring Joint
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 7 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
DATA SHEETS
NUMBER DESCRIPTION
60101 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SW
60102 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60103 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SWxTHDF
60104 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60105 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60106 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SW
60107 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60109 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60111 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL600 - RF - 125 µin.Ra
60113 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60114 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL600 - RF - 125 µin.Ra
60115 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL600 - RF - 125 µin.Ra
60118 Austenitic Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SWxTHDF
60119 Austenitic Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60120 Austenitic Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL600 - RF - 125 µin.Ra
60121 Austenitic Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SW
60122 Austenitic Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60123 Austenitic Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60124 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL600 - RF - 125 µin.Ra
60125 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60126 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SW
60127 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60128 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL600 - RF - 125 µin.Ra
60131 Austenitic Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL600 - RF - 125 µin.Ra
60132 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL600 - RF - 125 µin.Ra
60133 Copper - Bronze Gate-UB-Red.B-Solid wdg- NoRising stem-Int.seat - MSS-SP80 - CL200 - THDF
60134 Carbon Steel - Gate-BB-FB-Solid wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60137 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60138 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SWxTHDF
60139 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60141 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL600 - RF - 125 µin.Ra
60142 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60143 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL300 - RF - 125 µin.Ra
60144 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SWxTHDF
60145 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL300 - RF - 125 µin.Ra
60148 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60149 Carbon Steel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SWxTHDF
60154 Nickel - Gate-BB-Red.B-Solid wdg-Exp.seat - API602 - CL800 - SW
60155 Nickel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL600 - RF - 125 µin.Ra
60156 Nickel - Gate-WB-Red.B-Solid wdg-Exp.seat - API602 - CL1500 - BW
60157 Nickel - Gate-PS-FB-Flex wdg-Wldd seat - ASME-B16.34 - CL900 - BW
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 8 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
Contractor: PEDEC
Consultant:
Sheet 9 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
60245 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
60246 Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60247 Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60248 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
60250 Nickel - Globe-BB-Disk-Thdd seat - BS1873 - CL150 - RF - 125 µin.Ra
60251 Nickel - Globe-BB-Disk-Thdd seat - BS1873 - CL300 - RF - 125 µin.Ra
60252 Carbon Steel - Globe-BB-Red.B-Thdd seat - BS5352 - CL800 - SW
60253 Carbon Steel - Globe-BB-Disk-Thdd seat - BS1873 - CL600 - RF - 125 µin.Ra
60254 Carbon Steel - Globe-BB-Disk-Thdd seat - BS1873 - CL600 - RF - 125 µin.Ra
60255 Austenitic Steel - Globe-BB-Red.B-Thdd seat - BS5352 - CL800 - SW
60256 Austenitic Steel - Globe-BB-Disk-Thdd seat - BS1873 - CL300 - RF - 125 µin.Ra
60257 Austenitic Steel - Globe-WB-Red.B-Thdd seat - BS5352 - CL1500 - SW
60258 Austenitic Steel - Globe-PS-Disk-Int.seat - BS1873 - CL1500 - RJ (F)
60259 Austenitic Steel - Globe-PS-Disk-Int.seat - BS1873 - CL900 - RJ (F)
60260 Carbon Steel - Globe-PS-Disk-Int.seat - BS1873 - CL2500 - BW
60261 Carbon Steel - Angle Globe-PS-Guided Piston-Integral seat - ASME-B16.34 - CL2500 - BW
60262 Carbon Steel - Globe - FLG API 6A - CL 10000
60263 Carbon Steel - Angle Globe - FLG API 6A - CL 10000
60305 Carbon Steel - Check-Wafer-Dual plate-Wldd seat - API594 - CL300 - RF - 125 µin.Ra
60306 Carbon Steel - Check-Wafer-Dual plate-Wldd seat - API594 - CL600 - RF - 125 µin.Ra
60307 Carbon Steel - Check-Wafer-Dual plate-Wldd seat - API594 - CL600 - RF - 125 µin.Ra
60310 Austenitic Steel - Check-BB-Red.B-Ball-Thdd seat - BS5352 - CL800 - SW
60311 Austenitic Steel - Check-Wafer-Dual plate-Wldd seat - API594 - CL150 - RF - 125 µin.Ra
60312 Austenitic Steel - Check-Wafer-Dual plate-Wldd seat - API594 - CL300 - RF - 125 µin.Ra
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 10 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
Contractor: PEDEC
Consultant:
Sheet 11 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
60410 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60411 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL600 - RF - 125 µin.Ra
Austenitic Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
60412
µin.Ra
60414 Austenitic Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
Austenitic Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
60415
µin.Ra
60416 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60420 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
60421 Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60422 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
60423 Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60425 Austenitic Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60426 Austenitic Steel - Ball-Split body-FB-Trunnion ball - API6D - CL150 - RF - 125 µin.Ra
60427 Austenitic Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60428 Austenitic Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60431 Austenitic Steel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60432 Austenitic Steel - Ball-Split body-FB-Trunnion ball - API6D - CL600 - RF - 125 µin.Ra
60433 Austenitic Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
60434 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60435 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL600 - RF - 125 µin.Ra
60436 Copper - Bronze Ball-End entry-FB-Floating ball - <MFR Std - Metallic> - CL200 - THDF
60438 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60439 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL150 - RF - 125 µin.Ra
60440 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60441 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60444 Nickel - Ball-Split body-FB-Trunnion ball - API6D - CL1500 - RJ (F)
60445 Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
60446 Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
60447 Nickel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60448 Nickel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
60449 Nickel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60450 Nickel - Ball-Split body-FB-Trunnion ball - API6D - CL600 - RF - 125 µin.Ra
60451 Nickel - Ball-Split body-FB-Trunnion ball - API6D - CL900 - RJ (F)
60452 Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL1500 - RJ (F)
60453 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL1500 - RJ (F)
60454 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL900 - RJ (F)
60455 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL1500 - RJ (F)
60456 Austenitic Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60461 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60462 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL150 - RF - 125 µin.Ra
60464 Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 12 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
60466 Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
60467 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60468 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL150 - RF - 125 µin.Ra
60469 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL150 - RF - 125 µin.Ra
60470 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL150 - RF - 125 µin.Ra
60471 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60472 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60473 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60474 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60475 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL600 - RF - 125 µin.Ra
60476 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL600 - RF - 125 µin.Ra
60477 Carbon Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60478 Carbon Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60481 Austenitic Steel - Ball-Split body-FB-Floating ball - API6D - CL300 - RF - 125 µin.Ra
60482 Austenitic Steel - Ball-Split body-FB-Trunnion ball - API6D - CL300 - RF - 125 µin.Ra
60489 Carbon Steel - Ball-Split body-Red.B-Floating ball - BS5351 - CL600 - RF - 125 µin.Ra
60500 Carbon Steel - Butterfly-Wafer-Sleeve type-Centered disk - API609 - CL150 - RF - 125 µin.Ra
60501 Carbon Steel - Butterfly-Flanged-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
60503 Carbon Steel - Butterfly-Lug wafer-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
60504 Carbon Steel - Butterfly-Flanged-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
60505 Carbon Steel - Butterfly-Lug wafer-Triple Off Set-Int.seat-Fire safe - API609 - CL300 - RF - 125 µin.Ra
60516 Carbon Steel - Gate-BB-FB-Flex wdg-Thdd seat - API600 - CL150 - RF - 125 µin.Ra
60517 Austenitic Steel - Gate-WB-Red.B-Solid wdg-Exp.seat - API602 - CL1500 - SW
60518 Austenitic Steel - Gate-PS-FB-Flex wdg-Wldd seat - ASME-B16.34 - CL1500 - RJ (F)
60519 Austenitic Steel - Gate-PS-FB-Flex wdg-Wldd seat - ASME-B16.34 - CL900 - RJ (F)
60520 Carbon Steel - Gate-PS-FB-Flex wdg-Wldd seat - ASME-B16.34 - CL2500 - BW
60521 Carbon Steel - Gate- Throught conduit - CL 10000 API 6A
60522 Stainless Steel - Gate- Throught conduit - CL 10000 API 6A
60600 Carbon Steel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
60601 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL150 - RF - 125 µin.Ra
60602 Carbon Steel - T Strainer-BW - <MFR Std - Metallic> - CL150 - RF - 125 µin.Ra
60603 Carbon Steel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
60604 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL150 - RF - 125 µin.Ra
60605 Carbon Steel - T Strainer-BW - <MFR Std - Metallic> - CL150 - RF - 125 µin.Ra
60607 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL300 - RF - 125 µin.Ra
60608 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL600 - RF - 125 µin.Ra
60609 Austenitic Steel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
60610 Austenitic Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL150 - RF - 125 µin.Ra
60611 Austenitic Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL300 - RF - 125 µin.Ra
60612 Carbon Steel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
60613 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL300 - RF - 125 µin.Ra
60614 Carbon Steel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
60615 Carbon Steel - Y Strainer-Bolted cover - ASME-B16.34 - CL150 - RF - 125 µin.Ra
60616 Carbon Steel - T Strainer-BW - <MFR Std - Metallic> - CL150 - RF - 125 µin.Ra
60617 Nickel - Y Strainer - Union bonnet - ASME-B16.34 - CL800 - SW
Client: Document No.:
00-GA-E-60001
Contractor: PEDEC
Consultant:
Sheet 13 of 529
Plant Location: DARQUAIN OIL FIELD, IRAN Rev.: 4
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:26 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60400 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60401 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60315 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60316 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60128 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60104 Flgd 300# Conns. GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60103 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60101 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60102 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60105 on Equ't. GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60200 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60201 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60602 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60600 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60601 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:29 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60010 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60010 Taps on Equ't. BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 300# flanged conns. WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 10 10 ASME B16.5 FLG x BW 900 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:32 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60010
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60010
2 12
Gasket 1/2 24 ASME B16.21 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- Only for mating to GAS
LB AARH) WOUND/GRAPHITE 60012 300# flanged conns.
Gasket 1/2 1+1/2 ASME B16.21 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 10 10 ASME B16.21 FLG 900 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:38 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11A Branch Table 11A
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:08:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:02 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60461 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60462 on P&ID. BAL
Valve Butterfly 3 14 API 609/ASME B16.5- LUG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV
STD LUG LB AARH) 60503 BFY
Valve Butterfly 16 24 API 609/ASME B16.5- FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV
STD.FLG. LB AARH) 60504 BFY
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60345 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60346 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60174 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60171 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60173 Flgd 300# Conns. GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60172 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60175 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60176 on Equ't. GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60240 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60241 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60631 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60629 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60630 WYE
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:05 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60011 Taps on Equ't. BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 300# flanged conns. WNK
Flange Welding Neck 10 10 ASME B16.5 FLG x BW 900 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:08 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 6000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 12
Gasket 1/2 24 ASME B16.21 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- Only for mating to GAS
LB AARH) WOUND/GRAPHITE 60012 300# flanged conns.
Gasket 1/2 1+1/2 ASME B16.21 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 10 10 ASME B16.21 FLG 900 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Nipple L=100 mm 1+1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:10 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11C Branch Table 11C
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:16 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:21 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:35 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60467 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60468 on P&ID. BAL
Valve Ball Reducer Bore 1/2 1+1/2 BS 5351 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- For use only if shown VALV 08
LB AARH) 60489 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60317 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60329 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60109 Flgd 300# Conns. GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60149 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60111 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60106 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60148 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60113 on Equ't. GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60202 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60224 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60616 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60614 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60615 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:38 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60011 Taps on Equ't. BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 300# flanged conns. WNK
Flange Welding Neck 10 10 ASME B16.5 FLG x BW 900 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 RED
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:41 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 12
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ INCONEL 625 GA-E- Only for mating to GAS
LB AARH) SPIRAL 60012 300# flanged conns.
WOUND/GRAPHITE
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 10 10 ASME B16.20 FLG 900 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:43 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:48 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11D Branch Table 11D
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:50 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:09:56 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:08 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 12 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60402 on P&ID. BAL
Valve Ball Full Bore 6 12 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60403 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60354 CHK
Valve Check 2 12 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60324 CHK
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60198 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60190 GAT
Valve Gate 2 12 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60516 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60252 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60219 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60636 WYE
Strainer Y-Type 2 12 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60641 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Drip Ring 2 12 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 12 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 12 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:11 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
Reducer Concentric 3 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 10
Reducer Eccentric 3 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 10
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
Cap 2 12 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
Sockolet 2 12 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 12 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60010
1/2 1+1/2
Weldolet 6 12 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60010
2 12
Gasket 1/2 1+1/2 ASME B16.21 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Gasket 1/2 12 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:18 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11E Branch Table 11E
Branch 12 TE Branch
Size 10 TR TE S Sockolet
8 TR TR TE
TE Tee Equal
6 TR TR TR TE
TR Tee Reducing
4 W TR TR TR TE
W Weldolet
3 W W W TR TR TE
2 W W W W TR TR TE
1H S S S S S S S TE
1 S S S S S S S TR TE
TQ S S S S S S S TR TR TE
H S S S S S S S TR TR TR TE
12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:20 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:26 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60438 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60439 on P&ID. BAL
Valve Butterfly 16 24 API 609/ASME B16.5- FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV
STD.FLG. LB AARH) 60501 BFY
0
Valve Butterfly 26 30 API 609/ASME B16.47 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV
SERIE A-HI PERF. FLG. LB AARH) 60502 BFY
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60349 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60326 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60141 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60181 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60139 Flgd 300# Conns. GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60138 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60137 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60182 on Equ't. GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60220 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60221 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60622 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60623 WYE
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:43 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60624 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60011 Taps on Equ't. BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 300# flanged conns. WNK
Flange Welding Neck 10 10 ASME B16.5 FLG x BW 900 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 STR
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 12
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- Only for mating to GAS
LB AARH) WOUND/GRAPHITE 60012 300# flanged conns.
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 10 10 ASME B16.20 FLG 900 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:48 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:52 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11G Branch Table 11G
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:10:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:01 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:18 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60469 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60470 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60313 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60318 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60124 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60125 Flgd 300# Conns. GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60144 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60126 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60107 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60145 on Equ't. GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60213 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60203 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60605 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60612 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60604 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 150# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60011 Taps on Equ't. BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 300# flanged conns. WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
Flange Welding Neck 10 10 ASME B16.5 FLG x BW 900 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60011 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:25 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 6000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 12
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ INCONEL 625 GA-E- Only for mating to GAS
LB AARH) SPIRAL 60012 300# flanged conns.
WOUND/GRAPHITE
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 10 10 ASME B16.20 FLG 900 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1+1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:31 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11J Branch Table 11J
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:34 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:55 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Valve Butterfly 4 24 API 609/ASME B16.5- WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- See Note 1 VALV 05
STD.WAF. LB AARH) 60500 BFY
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60315 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60316 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Use also for matching VALV 03
LB AARH) 60128 300# Equ't Nozzles GAT
Valve Gate 1/2 1+1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- Use for Ins. Conns. VALV 02
60103 Only GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60101 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 03
LB AARH) 60105 on Equ't GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Use 4" & larger only VALV 01
LB AARH) 60102 were shown on P&ID GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60200 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60201 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer T -Type 14 24 SP TB.5050 BW 150 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60602 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60600 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60601 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60010 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:11:58 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 150# flanged conns.
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Use only for Press. FLG
LB AARH) 60010 Taps on Equ't. BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) 60010 300# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:01 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60010
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60010
2 12
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- Only for mating with GAS
LB AARH) WOUND/GRAPHITE 60012 300# flanged conns.
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:06 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 11R Branch Table 11R
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:08 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:15 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:30 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 16 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Butterfly 3 16 API 609/ASME B16.5- LUG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 02
STD LUG LB AARH) 60505 BFY
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60313 CHK
Valve Check 2 16 API 594 WAFER 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60314 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 15
LB AARH) 60124 Flgd 600# Conns. GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 13
LB AARH) 60125 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60126 GAT
Valve Gate 2 16 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60127 GAT
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60011 STS
Strainer T -Type 14 16 SP TB.5050 BW 300 R.F. (125-250 WROUGHT-S ASTM A 234 GR. WPB GA-E- STR
LB AARH) 60631 WYE
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60612 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60613 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 16 SP TB.5011 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 16 SP TB.5039 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:33 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Blind 2 16 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 2 16 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 12
Reducer Eccentric 3 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 12
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 16 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 16 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 16 SP TB.5380 THRD-F 6000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:36 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:42 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 13C Branch Table 13C
Branch 16 TE Branch
Size 14 TR TE S Sockolet
12 TR TR TE
TE Tee Equal
10 TR TR TR TE
TR Tee Reducing
8 TR TR TR TR TE
W Weldolet
6 TR TR TR TR TR TE
4 W W W TR TR TR TE
3 W W W W W TR TR TE
2 W W W W W W TR TR TE
1H S S S S S S S S S TE
1 S S S S S S S S S TR TE
TQ S S S S S S S S S TR TR TE
H S S S S S S S S S TR TR TR TE
16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:44 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:51 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:12:55 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:08 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 30 30 ASME B36.10 BE E.F.W. ASTM A 672 GR. C60 GA-E- PIP
CL. 12 60010
Valve Ball Full Bore 2 4 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60440 on P&ID. BAL
The use is limited to
200°C
Valve Ball Full Bore 6 24 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60441 on P&ID. BAL
The use is limited to
200°C
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60348 CHK
Valve Check 2 24 API 594 WAFER 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60327 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60179 Equ't Nozzles GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60177 GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- See Note 1 VALV
60178 GAT
Valve Gate 1/2 1+1/2 BS 5352 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 04
LB AARH) 60180 Flgd 600# Conns. GAT
Valve Gate 2 24 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB AARH) 60142 GAT
Valve Gate 30 30 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV
LB AARH) 60143 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60242 GLB
Valve Globe 2 8 BS 1873 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60222 GLB
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 2 12 SP TB.5007 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60600 WYE
Strainer Y-Type 2 16 ASME B16.34 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60625 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:11 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Drip Ring 2 24 SP TB.5011 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60010
Spacer & Blind 14 24 SP TB.5039 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60010 PAC
Spacer & Blind 30 30 MFRS.STD/GA-E-60019 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 24 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 1/2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60010 only for mating to WNK
300# flanged conns.
Flange Welding Neck 30 30 ASME B16.47 SERIE A FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
Reducer Concentric 3 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 24
Reducer Eccentric 3 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 24
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 3 30 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
2 24
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Cap 2 30 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
Sockolet 2 30 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 30 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60010
1/2 1+1/2
Weldolet 6 30 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60010
2 8
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- 1/2" - 1 1/2" sizes GAS
LB AARH) WOUND/GRAPHITE 60012 only for mating to
flanged conns.
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 30 30 ASME B16.20/ASME FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
B16.47 SERIE A LB AARH) WOUND/GRAPHITE 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1+1/2
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:20 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 13G Branch Table 13G
Branch 30 TE Branch
Size 24 TR TE S Sockolet
20 TR TR TE
TE Tee Equal
18 TR TR TR TE
TR Tee Reducing
16 TR TR TR TR TE
W Weldolet
14 TR TR TR TR TR TE
12 TR TR TR TR TR TR TE
10 TR TR TR TR TR TR TR TE
8 W W TR TR TR TR TR TR TE
6 W W W W TR TR TR TR TR TE
4 W W W W W W W TR TR TR TE
3 W W W W W W W W W TR TR TE
2 W W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S S TE
1 S S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S S TR TR TR TE
30 24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24, 30=30
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:23 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:30 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60473 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60474 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60317 CHK
Valve Check 2 24 API 594 WAFER 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60305 CHK
Valve Gate 1/2 1+1/2 BS 5352 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60109 Equ't Nozzles GAT
Valve Gate 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60106 GAT
Valve Gate 1/2 1+1/2 BS 5352 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 10
LB AARH) 60111 Flgd 600# Conns. GAT
Valve Gate 2 24 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB AARH) 60113 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60202 GLB
Valve Globe 2 8 BS 1873 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60205 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.11/MANUF. SW-F 800# FORGED ASTM A 105 GA-E- STR
STD 60603 WYE
Strainer Y-Type 2 2 ASME B16.5/MANUF. FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
STD LB AARH) 60607 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 24 SP TB.5011 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 24 SP TB.5039 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 24 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:51 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Welding Neck 1/2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60011 only for mating to WNK
flanged conns.
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 30 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Isolating Kit 1 1+1/2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
Isolating Kit 2 2 MANUFACTURE STD FLG 300 R.F. (125-250 GA-E-
LB AARH) 60018
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:13:59 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 13H Branch Table 13H
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:06 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:17 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 12 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60354 CHK
Valve Check 2 12 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60355 CHK
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 10
Bleed LB AARH) 60485 DBB
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60190 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 35
LB AARH) 60191 600# Equ't nozzles. GAT
Valve Gate 2 12 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60192 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60252 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60253 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60636 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60637 WYE
Spacer & Blind 12 12 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60010 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange Blind 1/2 12 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 12 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 3 12 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM A 105 GA-E- Only for mating to FLG
LB 60010 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:20 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Reducer Concentric 3 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 10
Reducer Eccentric 3 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 10
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 3 12 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
2 10
Cap 2 12 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
Sockolet 2 12 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 12 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60010
1/2 1+1/2
Weldolet 6 12 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60010
2 6
Gasket 1/2 12 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 3 12 ASME B16.20 FLG 900 Ring Joint _ SOFT IRON RING GA-E- GAS
LB JOINT 60010
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:26 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 15B Branch Table 15B
Branch 12 TE Branch
Size 10 TR TE S Sockolet
8 TR TR TE
TE Tee Equal
6 TR TR TR TE
TR Tee Reducing
4 W TR TR TR TE
W Weldolet
3 W W W TR TR TE
2 W W W W TR TR TE
1H S S S S S S S TE
1 S S S S S S S TR TE
TQ S S S S S S S TR TR TE
H S S S S S S S TR TR TR TE
12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:28 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:33 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 3/4 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 16 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Check 3/4 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60313 CHK
Valve Check 2 16 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60322 CHK
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Threaded 1/2" NPT VALV 10
Bleed LB AARH) 60464 female, Use for PI DBB
conns. Only
Valve Double Block & 1 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 12
Bleed LB AARH) 60466 DBB
Valve Gate 3/4 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60126 GAT
Valve Gate 3/4 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 35
LB AARH) 60124 600# Equ't nozzles. GAT
Valve Gate 2 16 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60132 GAT
Valve Globe 3/4 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60213 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60217 GLB
Strainer Y-Type 3/4 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60612 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60634 WYE
Spacer & Blind 12 16 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 3/4 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 3/4 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange Blind 3/4 16 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 3/4 16 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60011 only for mating to WNK
flanged conns.
45° Elbow 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
90° Elbow Long Radius 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 14
Reducer Eccentric 3 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 14
Tee Equal 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 3 16 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
2 14
Cap 2 16 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Isolating Kit 1 2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
Plug Hex Head 3/4 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 3/4 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 16 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 16 SP TB.5380 THRD-F 6000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 16 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 6
Gasket 3/4 16 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 3/4 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:50 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 15E Branch Table 15E
Branch 16 TE Branch
Size 14 TR TE S Sockolet
12 TR TR TE
TE Tee Equal
10 TR TR TR TE
TR Tee Reducing
8 TR TR TR TR TE
W Weldolet
6 TR TR TR TR TR TE
4 W W W TR TR TR TE
3 W W W W W TR TR TE
2 W W W W W W TR TR TE
1H S S S S S S S S S TE
1 S S S S S S S S S TR TE
TQ S S S S S S S S S TR TR TE
H S S S S S S S S S TR TR TR TE
16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:14:56 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:02 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:05 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:16 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 16 16 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB 36-SP-014 GA-E- VALV 61
Nozzle Type STD LB AARH) 60025 CHK
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 26 30 ASME B36.10 BE E.F.W. ASTM A 672 B60 GA-E- PIP
CL.22 60011
Valve Ball Reducer Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 07
LB AARH) 60487 BAL
Valve Ball Reducer Bore 6 24 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 07
LB AARH) 60488 BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60349 CHK
Valve Check 2 24 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60356 CHK
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60181 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 35
LB AARH) 60141 600# Equ't nozzles. GAT
Valve Gate 2 24 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60193 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60220 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60254 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60623 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60638 WYE
Spacer & Blind 10 24 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 8 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange Blind 1/2 24 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 1/2 24 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60011 only for mating to WNK
flanged conns.
Flange Welding Neck 26 30 ASME B16.47 SERIE A FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 WNK
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:18 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
45° Elbow Long Radius 26 30 ASME B16.9 BW WROUGHT-W ASTM A 234 GR. WPB GA-E- 45L
60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
90° Elbow Long Radius 26 30 ASME B16.9 BW WROUGHT-W ASTM A 234 GR. WPB GA-E- 90L
60011 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 20
Reducer Eccentric 26 30 ASME B16.9 BW WROUGHT-W ASTM A 234 GR. WPB RED
ECC
18 28
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Equal 26 30 ASME B16.9 BW WROUGHT-W ASTM SA234 GR. GA-E- TEE
WPB 60011 STR
26 30
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
2 20
Tee Reducing 26 30 ASME B16.9 BW WROUGHT-W ASTM A 234 GR. WPB GA-E- TEE
60011 RED
10 28
Cap 2 30 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Isolating Kit 1 2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:21 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 30 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 30 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 30 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 6
Gasket 1/2 30 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1+1/2
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:26 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 15F Branch Table 15F
Branch 30 TE Branch
Size 28 TR TE I Pipe to Pipe
26 TR TR TE
S Sockolet
24 I TR TR TE
TE Tee Equal
20 I I TR TR TE
TR Tee Reducing
18 I I I TR TR TE
16 I I I I TR TR TE
14 I I I I I TR TR TE
12 I I I I I I TR TR TE
10 I I I I I I I TR TR TE
8 I I I I I I I I TR TR TE
6 I I I I I I I I I TR TR TE
4 I I I I I I I I I I TR TR TE
3 I I I I I I I I I I I TR TR TE
2 I I I I I I I I I I I I TR TR TE
1H S S S S S S S S S S S S S S TR TE
1 S S S S S S S S S S S S S S TR TR TE
TQ S S S S S S S S S S S S S S TR TR TR TE
H S S S S S S S S S S S S S S S TR TR TR TE
30 28 26 24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24, 26=26, 28=28, 30=30
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:28 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:34 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 2 20 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Valve Ball Full Bore 1/2 1+1/2 BS 5351 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- For use only if shown VALV 08
LB AARH) 60416 on P&ID. BAL
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60410 on P&ID. BAL
Valve Ball Full Bore 6 20 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60411 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60315 CHK
Valve Check 2 20 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60306 CHK
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Use for PI conns. VALV 12
Bleed LB AARH) 60245 Only DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- Use for Orifice Taps VALV 11
Bleed 60248 only DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Use for PI conns. VALV 10
Bleed LB AARH) 60247 Only DBB
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Threaded 1/2" NPT VALV
Bleed LB AARH) 60246 female, Use for PI DBB
conns. Only
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60128 600# Equ't nozzles. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60101 GAT
Valve Gate 2 20 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB AARH) 60114 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60200 GLB
Valve Globe 2 12 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60206 GLB
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60600 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60608 WYE
Spacer & Blind 12 20 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60010 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60010 PEC
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:50 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010
Flange Blind 1/2 20 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 2 ASME B16.5 FLG x BW 1500 Ring Joint FORGED ASTM A 105 GA-E- Only for mating to FLG
LB 60010 1500# flanged conns. WNK
Flange Welding Neck 2 20 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 3 20 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM A 105 GA-E- Only for mating to FLG
LB 60010 900# flanged conns. WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
Reducer Concentric 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 18
Reducer Eccentric 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 18
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
2 18
Cap 2 20 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60010 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:52 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:57 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 15G Branch Table 15G
Branch 20 TE Branch
Size 18 TR TE S Sockolet
16 TR TR TE
TE Tee Equal
14 TR TR TR TE
TR Tee Reducing
12 TR TR TR TR TE
W Weldolet
10 TR TR TR TR TR TE
8 TR TR TR TR TR TR TE
6 W W TR TR TR TR TR TE
4 W W W W W TR TR TR TE
3 W W W W W W W TR TR TE
2 W W W W W W W W TR TR TE
1H S S S S S S S S S S S TE
1 S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S TR TR TR TE
20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:15:58 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:02 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:10 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 20 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60475 on P&ID. BAL
Valve Ball Full Bore 6 20 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60476 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60317 CHK
Valve Check 2 20 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60307 CHK
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 12
Bleed LB AARH) 60422 DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD SW-F x THRD-F 800# FORGED ASTM A 105 GA-E- Use for Orifice Taps VALV 11
Bleed 60420 only DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Use for PI conns. VALV 10
Bleed LB AARH) 60421 Only DBB
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Threaded 1/2" NPT VALV 10
Bleed LB AARH) 60423 female, Use for PI DBB
conns. Only
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 03
LB AARH) 60111 600# Equ't nozzles. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60106 GAT
Valve Gate 2 20 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60115 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60202 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60207 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60603 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60626 WYE
Spacer & Blind 12 20 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
Flange Blind 1/2 20 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:12 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Welding Neck 1/2 20 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60011 only for mating to WNK
flanged conns.
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 18
Reducer Eccentric 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 18
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 3 20 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
2 18
Cap 2 20 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Isolating Kit 1 2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1/2 1+1/2 MANUFACTURE STD SW-F 3000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 20 SP TB.5380 SW-F 3000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 20 SP TB.5380 THRD-F 3000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:13 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:17 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 15H Branch Table 15H
Branch 20 TE Branch
Size 18 TR TE S Sockolet
16 TR TR TE
TE Tee Equal
14 TR TR TR TE
TR Tee Reducing
12 TR TR TR TR TE
W Weldolet
10 TR TR TR TR TR TE
8 TR TR TR TR TR TR TE
6 W W TR TR TR TR TR TE
4 W W W W W TR TR TR TE
3 W W W W W W W TR TR TE
2 W W W W W W W W TR TR TE
1H S S S S S S S S S S S TE
1 S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S TR TR TR TE
20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:18 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:31 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 4 ASME B36.10 BW SEAMLESS ASTM A 106 GR. B GA-E- PIP
60010
Pipe 6 24 ASME B36.10 BE SEAMLESS API 5L GR. X60 GA-E- PIP
60010
Valve Ball Full Bore 2 2 API 6D FLG 1500 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 08
LB 60453 BAL
Valve Ball Full Bore 3 12 API 6D FLG 900 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 08
LB 60454 BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 1500 FORGED ASTM A 105 GA-E- VALV 06
LB 60334 CHK
Valve Check 2 2 API 594 LUG 1500 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB 60336 CHK
Valve Check 3 24 API 594 LUG 900 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB 60335 CHK
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 1500 Ring Joint FORGED ASTM A 105 GA-E- Use for PI conns. VALV 12
Bleed LB 60455 Only DBB
Valve Gate 1/2 1+1/2 API 602 SW-F 1500 FORGED ASTM A 105 GA-E- VALV 01
LB 60160 GAT
Valve Gate 2 2 ASME B16.34 FLG 1500 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB 60162 GAT
Valve Gate 3 24 ASME B16.34 FLG 900 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB 60161 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 1500 FORGED ASTM A 105 GA-E- VALV 04
LB 60229 GLB
Valve Globe 2 2 BS 1873 FLG 1500 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB 60231 GLB
Valve Globe 3 8 BS 1873 FLG 900 Ring Joint CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB 60230 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 1500 FORGED ASTM A 105 GA-E- STR
LB 60621 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 1500 Ring Joint CAST ASTM A 216 GR. WCB GA-E- STR
LB 60620 WYE
Spacer & Blind 12 20 SP TB.5039 WAFER 900 Ring Joint FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB 70 60010 PAC
Spectacle Blind 1/2 2 SP TB.5038 WAFER 1500 Ring Joint FORGED ASTM A 105 GA-E- LNBDS
LB 60010 PEC
Spectacle Blind 3 10 SP TB.5038 WAFER 900 Ring Joint FORGED ASTM A 105 GA-E- LNBDS
LB 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 1500 Ring Joint FORGED ASTM A 105 GA-E- FLG
LB 60010
Flange Blind 1/2 2 ASME B16.5 FLG 1500 Ring Joint FORGED ASTM A 105 GA-E- FLG
LB 60010 BLD
Flange Blind 3 24 ASME B16.5 FLG 900 Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
LB 60010 BLD
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:33 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Welding Neck 2 2 ASME B16.5 FLG x BW 1500 Ring Joint FORGED ASTM A 105 GA-E- FLG
LB 60010 WNK
Flange Welding Neck 3 4 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM A 105 GA-E- FLG
LB 60010 WNK
Flange Welding Neck 6 24 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
LB 60010 WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60010
45° Elbow Long Radius 2 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60010 LR
45° Elbow Long Radius 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- 45L
W 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60010
90° Elbow Long Radius 2 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60010 LR
90° Elbow Long Radius 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- 90L
W 60010 LR
Reducer Concentric 3 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 CON
2 3
Reducer Concentric 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- RED
W 60010 CON
2 20
Reducer Eccentric 3 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60010 ECC
2 3
Reducer Eccentric 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- RED
W 60010 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60010 STR
Tee Equal 2 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 STR
Tee Equal 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- TEE
W 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60010 RED
Tee Reducing 3 4 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60010 RED
2 3
Tee Reducing 6 24 ASME B16.9 BW WROUGHT-S or ASTM A860 WPHY60 GA-E- TEE
W 60010 RED
2 20
Cap 2 4 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:34 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:38 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 16B Branch Table 16B
Branch 24 TE Branch
Size 20 TR TE TE Tee Equal
18 TR TR TE
TR Tee Reducing
16 TR TR TR TE
W Weldolet
14 TR TR TR TR TE
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H W W W W W W W W W W W W TE
1 W W W W W W W W W W W W TR TE
TQ W W W W W W W W W W W W TR TR TE
H W W W W W W W W W W W W TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:51 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 12 12 ASME B16.34/MANUF. FLG 2500 Ring Joint CAST ASTM A 216 GR. WCB 36-SP-001 GA-E- VALV 61
Nozzle Type STD LB 60025 CHK
Valve Check Non Slam 12 12 ASME B16.34/MANUF. FLG 2500 Ring Joint CAST ASTM A 216 GR. WCB 36-SP-002 GA-E- VALV 62
Nozzle Type STD LB 60025 CHK
Pipe 2 20 MANUFACTURE STD BE SEAMLESS API 5L GR. X60 GA-E- PIP
60010
Valve Angle 3 3 ASME B16.34 BW 2500 CAST ASTM A 216 GR. WCB GA-E- VALV
LB 60261 ANG
Valve Check 3 14 MANUFACTURE STD BW 2500 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB 60362 CHK
Valve Gate 3 14 ASME B16.34 BW 2500 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB 60520 GAT
Valve Globe 3 12 BS 1873 BW 2500 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB 60260 GLB
Spacer & Blind 2 12 SP TB.5039 WAFER 2500 R.F. (125-250 FORGED ASTM A 694 F60 GA-E- LNBDS
LB AARH) 60010 PAC
Flange Blind 2 12 ASME B16.5 FLG 2500 R.F. (125-250 FORGED ASTM A 694 F60 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 12 ASME B16.5 FLG x BW 2500 Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
LB 60010 WNK
45° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 45L
60010 LR
90° Elbow Long Radius 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 90L
60010 LR
Reducer Concentric 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
60010 CON
2 18
Reducer Eccentric 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
60010 ECC
2 20
Tee Equal 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60010 STR
Tee Reducing 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60010 RED
Cap 2 20 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- CAP
60010
Weldolet 2 20 SP TB.5004 BW FORGED ASTM A 694 F60 GA-E- WOL
60010
2 18
Gasket 2 12 ASME B16.21 FLG 2500 Ring Joint _ SOFT IRON RING GA-E- GAS
LB JOINT 60012
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:55 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 18A Branch Table 18A
Branch 20 TE Branch
Size 18 TR TE TE Tee Equal
16 TR TR TE
TR Tee Reducing
14 TR TR TR TE
W Weldolet
12 TR TR TR TR TE
10 TR TR TR TR TR TE
8 TR TR TR TR TR TR TE
6 W W TR TR TR TR TR TE
4 W W W W W TR TR TR TE
3 W W W W W W W TR TR TE
2 W W W W W W W W TR TR TE
20 18 16 14 12 10 8 6 4 3 2
Run Size
Sizes translation 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20
3
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:16:59 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:05 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 12 12 ASME B16.34/MANUF. FLG 2500 Ring Joint CAST ASTM A 216 GR. WCB 36-SP-003 GA-E- VALV 61
Nozzle Type STD LB 60025 CHK
Pipe 2 14 MANUFACTURE STD BE SEAMLESS API 5L GR. X60 GA-E- PIP
60010
Valve Check 12 14 MANUFACTURE STD BW 2500 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB 60363 CHK
Spacer & Blind 2 12 SP TB.5039 WAFER 2500 R.F. (125-250 FORGED ASTM A 694 F60 GA-E- LNBDS
LB AARH) 60010 PAC
Flange Blind 2 12 ASME B16.5 FLG 2500 R.F. (125-250 FORGED ASTM A 694 F60 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 12 ASME B16.5 FLG x BW 2500 Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
LB 60010 WNK
45° Elbow Long Radius 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 45L
60010 LR
90° Elbow Long Radius 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 90L
60010 LR
Reducer Concentric 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
60010 CON
Reducer Eccentric 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
60010 ECC
Tee Equal 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60010 STR
Tee Reducing 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60010 RED
Cap 2 14 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- CAP
60010
Weldolet 2 14 SP TB.5004 BW FORGED ASTM A 694 F60 GA-E- WOL
60010
Gasket 2 12 ASME B16.21 FLG 2500 Ring Joint _ SOFT IRON RING GA-E- GAS
LB JOINT 60012
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:09 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 18B Branch Table 18B
Branch 20 TE Branch
Size 18 TR TE TE Tee Equal
16 TR TR TE
TR Tee Reducing
14 TR TR TR TE
W Weldolet
12 TR TR TR TR TE
10 TR TR TR TR TR TE
8 TR TR TR TR TR TR TE
6 W W TR TR TR TR TR TE
4 W W W W W TR TR TR TE
3 W W W W W W W TR TR TE
2 W W W W W W W W TR TR TE
20 18 16 14 12 10 8 6 4 3 2
Run Size
Sizes translation 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20
3
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
FOR FLANGES:
NPS 1"+1/2 CORRISPONDS TO API 6A 1"+13/16
NPS 2" CORRISPONDS TO API 6A 1"+13/16
NPS 3" CORRISPONDS TO API 6A 1"+13/16
NPS 4" CORRISPONDS TO API 6A 2"+9/16
NPS 12" CORRISPONDS TO API 6A 9"
NPS 14" CORRISPONDS TO API 6A 9"
NPS 16" CORRISPONDS TO API 6A 11"
NPS 20" CORRISPONDS TO API 6A 13"+5/8
NPS 24" CORRISPONDS TO API 6A 16"+3/4
P Standard of design Mod Size Thk. Mod
I 313 ASME B31.3 1+1/2 15.81
2 18.05
3 23.46
4 28.13
12 67.32
14 73.29
16 82.62
20 101.65
24 120.68
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:15 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:19 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 12 12 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 36-SP-006 GA-E- VALV 61
Nozzle Type 10000 60025 CHK
Valve Check Non Slam 12 12 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 36-SP-005 GA-E- VALV 62
Nozzle Type 10000 60025 CHK
Pipe 1+1/2 24 ASME B36.10 BW SEAMLESS API 5L GR. X60 GA-E- PIP
60011
Valve Gate 1+1/2 24 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- VALV 01
10000 60522 GAT
Spacer & Blind type BX 1+1/2 24 API 6A / WAFER API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- LNBDS
MANUFACTURER STD 10000 60011 PAC
Flange Blind Type 6BX 1+1/2 24 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
10000 60011 BLD
Flange Welding Neck Type 1+1/2 24 API 6A FLG API 6A x BW API Ring Joint FORGED ASTM A 694 F60 GA-E- See GA-E-60024 FLG
6BX 10000 60011 WNK
45° Elbow Long Radius 1+1/2 24 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 45L
60011 LR
90° Elbow Long Radius 1+1/2 24 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 90L
60011 LR
Reducer Concentric 1+1/2 24 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
STD 60011 CON
Reducer Eccentric 1+1/2 24 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
STD 60011 ECC
Tee Equal 1+1/2 24 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60011 STR
Tee Reducing 1+1/2 24 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
STD 60011 RED
Cap 1+1/2 24 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- CAP
60011
Gasket 1+1/2 24 ASME B16.20 FLG API 6A-6BX API Ring Joint _ SOFT IRON RING OCTAGONAL GAS
10000 JOINT TYPE BX
3
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:24 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 19A Branch Table 19A
Branch 24 TE Branch
Size 20 TR TE TE Tee Equal
16 TR TR TE
TR Tee Reducing
14 TR TR TR TE
12 TR TR TR TR TE
4 TR TR TR TR TR TE
3 TR TR TR TR TR TR TE
2 TR TR TR TR TR TR TR TE
1H TR TR TR TR TR TR TR TR TE
24 20 16 14 12 4 3 2 1H
Run Size
Sizes translation 1H=1+1/2, 2=2, 3=3, 4=4, 12=12, 14=14, 16=16, 20=20, 24=24
4
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:25 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note:
FOR FLANGES:
NPS 1"+1/2 CORRISPONDS TO API 6A 1"+13/16
NPS 2" CORRISPONDS TO API 6A 1"+13/16
NPS 3" CORRISPONDS TO API 6A 1"+13/16
NPS 4" CORRISPONDS TO API 6A 2"+9/16
NPS 12" CORRISPONDS TO API 6A 9"
NPS 14" CORRISPONDS TO API 6A 9"
NPS 16" CORRISPONDS TO API 6A 11"
NPS 20" CORRISPONDS TO API 6A 13"+5/8
NPS 24" CORRISPONDS TO API 6A 16"+3/4
5
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:30 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
FOR FLANGES:
NPS 1"+1/2 CORRISPONDS TO API 6A 1"+ 13/16
NPS 2" CORRISPONDS TO API 6A 1"+ 13/16
NPS 3" CORRISPONDS TO API 6A 2"+ 1/16
NPS 4" CORRISPONDS TO API 6A 2"+ 9/16
NPS 6" CORRISPONDS TO API 6A 4"+ 1/16
NPS 8" CORRISPONDS TO API 6A 5"+1/8
NPS 10" CORRISPONDS TO API 6A 7"+1/16
NPS 12" CORRISPONDS TO API 6A 9"
NPS 14" CORRISPONDS TO API 6A 9"
NPS 16" CORRISPONDS TO API 6A 11"
P Standard of design Mod Size Thk. Mod
I 313 ASME B31.3 1+1/2 12.39
2 14.62
3 20.04
4 24.7
6 34.78
8 44.29
10 54.37
12 63.89
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:31 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:36 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 12 12 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 36-SP-007 GA-E- VALV 61
Nozzle Type 10000 60025 CHK
Pipe 1+1/2 16 ASME B36.10 BW SEAMLESS API 5L GR. X60 GA-E- PIP
60011
Valve Angle 4 4 MANUFACTURE STD FLG API 6A-6BX FORGED ASTM A 694 F60 GA-E- VALV
60263 ANG
Valve Gate 1+1/2 4 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- VALV 01
10000 60521 GAT
Valve Globe 4 4 MANUFACTURE STD FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- VALV
10000 60262 GLB
Spacer & Blind type BX 1+1/2 16 API 6A / WAFER API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- LNBDS
MANUFACTURER STD 10000 60011 PAC
Flange Blind Type 6BX 1+1/2 16 API 6A FLG API 6A-6BX API Ring Joint FORGED ASTM A 694 F60 GA-E- FLG
10000 60011 BLD
Flange Welding Neck Type 1+1/2 16 API 6A FLG API 6A x BW API Ring Joint FORGED ASTM A 694 F60 GA-E- See GA-E-60024 FLG
6BX 10000 60011 WNK
45° Elbow Long Radius 1+1/2 16 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 45L
60011 LR
90° Elbow Long Radius 1+1/2 16 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- 90L
60011 LR
Reducer Concentric 1+1/2 16 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
STD 60011 CON
Reducer Eccentric 1+1/2 16 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- RED
STD 60011 ECC
Tee Equal 1+1/2 16 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
60011 STR
Tee Reducing 1+1/2 16 ASME B16.9/MANUF. BW WROUGHT-S ASTM A860 WPHY60 GA-E- TEE
STD 60011 RED
Cap 1+1/2 16 ASME B16.9 BW WROUGHT-S ASTM A860 WPHY60 GA-E- CAP
60011
Gasket 1+1/2 16 ASME B16.20 FLG API 6A-6BX API Ring Joint _ SOFT IRON RING OCTAGONAL GAS
10000 JOINT TYPE BX
3
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 19B Branch Table 19B
Branch 16 TE Branch
Size 14 TR TE TE Tee Equal
12 TR TR TE
TR Tee Reducing
10 TR TR TR TE
8 TR TR TR TR TE
6 TR TR TR TR TR TE
4 TR TR TR TR TR TR TE
3 TR TR TR TR TR TR TR TE
2 TR TR TR TR TR TR TR TR TE
1H TR TR TR TR TR TR TR TR TR TE
16 14 12 10 8 6 4 3 2 1H
Run Size
Sizes translation 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
4
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:41 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
5
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:46 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:48 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:56 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.19 PL SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Pipe 2 8 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Pipe 10 42 ASME B36.19 BE E.F.W. ASTM A 358 GR. GA-E- PIP
316L CL.1 60010
Valve Ball Full Bore 2 4 API 6D FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- For use only if shown VALV 08
LB AARH) CF8M 60425 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- For use only if shown VALV 08
LB AARH) CF8M 60426 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 06
60310 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 06
LB AARH) CF8M 60311 CHK
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 01
60121 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Only for matching VALV 04
LB AARH) 60120 600# Equ't nozzles GAT
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Only for matching VALV 03
LB AARH) 60119 300# Equ't nozzles GAT
Valve Gate 1/2 1/2 API 602 SW-F x THRD-F 800# FORGED ASTM A 182 GR. F316 GA-E- See Note 1 VALV
60118 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- Only for Press. Taps VALV 03
LB AARH) CF8M 60184 on Equ't. GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 01
LB AARH) CF8M 60122 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 04
60210 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 04
LB AARH) CF8M 60211 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316 60010 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316 60010 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- STR
60609 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- STR
LB AARH) CF8M 60610 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- BLR
LB AARH) 60010
Drip Ring 2 24 SP TB.5011 WAFER 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- BLR
LB AARH) 60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:17:58 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- LNBDS
LB AARH) TP316 60010 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 30 42 MANUFACTURE STD WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- LNBDS
LB AARH) TP316 60610 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Only for mating to FLG
LB AARH) 60010 150# nozzles
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 30 42 ASME B16.47 SERIE A FLG 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Only for mating to FLG
LB AARH) 60010 300# flanged conns. WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 30 42 ASME B16.47 SERIE A FLG x BW 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- 45L
60010
45° Elbow Long Radius 2 42 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 45L
W WP316 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- 90L
60010
90° Elbow Long Radius 2 42 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 90L
W WP316 60010 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316 60010 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316 60010 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TEE
60010 STR
Tee Equal 2 42 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TEE
60010 RED
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:00 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 2 42 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316 60010 RED
Cap 2 42 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316 60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CPL
60010
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CPL
60010
1/2 1
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 182 GR. F316 GA-E- PLG
60010 HEX
Sockolet 2 42 SP TB.5380 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 42 SP TB.5380 THRD-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TOL
60010
1/2 1+1/2
Weldolet 2 42 SP TB.5004 BW FORGED ASTM A 182 GR. F316 GA-E- WOL
60010
2 10
Gasket 1/2 24 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL nozzles
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ INCONEL 625 GA-E- Only for mating to GAS
LB AARH) SPIRAL 60012 300# flanged conns.
WOUND/GRAPHITE
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 30 42 ASME B16.21/ASME FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- GAS
B16.47 SERIE A LB AARH) KLINGERSIL C4400 60013
OR EQUAL
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 312 TP 316 GA-E- XS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 312 TP 316 GA-E- XS NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 312 TP 316 GA-E- XS NIPP
60010
1/2 1+1/2
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:04 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 31A Branch Table 31A
Branch 42 TE Branch
Size 30 TR TE S Sockolet
24 TR TR TE
TE Tee Equal
20 TR TR TR TE
TR Tee Reducing
18 TR TR TR TR TE
W Weldolet
16 TR TR TR TR TR TE
14 W TR TR TR TR TR TE
12 W TR TR TR TR TR TR TE
10 W TR TR TR TR TR TR TR TE
8 W W W TR TR TR TR TR TR TE
6 W W W W W TR TR TR TR TR TE
4 W W W W W W W W TR TR TR TE
3 W W W W W W W W W W TR TR TE
2 W W W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S S S TE
1 S S S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S S S TR TR TR TE
42 30 24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24, 30=30, 42=42
6
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:06 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
7
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:10 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:16 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 2 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Valve Ball Full Bore 2 2 API 6D FLG 150 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV
LB AARH) CF8M 60456 BAL
Valve Check 1/2 1+1/2 BS 5352 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 06
60337 CHK
Valve Check 2 2 BS 5352 BW 150 FORGED ASTM A 182 GR. F316 GA-E- VALV 06
LB 60338 CHK
Valve Gate 1/2 1+1/2 API 602 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 01
60163 GAT
Valve Gate 2 2 API 600 BW 150 CAST ASTM A 351 GR. GA-E- VALV 01
LB CF8M 60164 GAT
Valve Globe 1/2 1+1/2 BS 5352 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 04
60232 GLB
Valve Globe 2 2 BS 1873 BW 150 CAST ASTM A 351 GR. GA-E- VALV 04
LB CF8M 60233 GLB
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316 60010 STS
Strainer Temporary Mesh 2 2 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316 60010 STS
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Spectacle Blind 2 2 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Blind 2 2 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 1/2 1+1/2 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
Flange Welding Neck 2 2 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
45° Elbow Long Radius 1/2 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 45L
WP316 60010 LR
90° Elbow Long Radius 1/2 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 90L
WP316 60010 LR
Reducer Concentric 3/4 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316 60010 CON
1/2 1+1/2
Reducer Eccentric 3/4 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316 60010 ECC
1/2 1+1/2
Tee Equal 1/2 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316 60010 STR
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:18 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 1/2 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316 60010 RED
Cap 1/2 2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316 60010
Weldolet 2 2 SP TB.5004 BW FORGED ASTM A 182 GR. F316 GA-E- WOL
60010
1/2 1/2
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/PTFE
Gasket 2 2 ASME B16.20 FLG 150 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/PTFE
3
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:21 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 31B Branch Table 31B
Branch 2 TE Branch
Size 1H TR TE TE Tee Equal
1 TR TR TE
TR Tee Reducing
TQ TR TR TR TE
W Weldolet
H W TR TR TR TE
2 1H 1 TQ H
Run Size
4
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:25 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:33 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.19 PL SEAMLESS ASTM A 312 TP 316L GA-E- PIP
60010
Pipe 2 8 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316L GA-E- PIP
60010
Pipe 10 10 ASME B36.19 BE E.F.W. ASTM A 358 GR. GA-E- PIP
316L CL.1 60010
Valve Ball Full Bore 2 4 API 6D FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 08
LB AARH) CF3M 60481 BAL
Valve Ball Full Bore 6 10 API 6D FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 08
LB AARH) CF3M 60482 BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. GA-E- VALV 06
F316L 60357 CHK
Valve Check 2 10 API 594 WAFER 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 06
LB AARH) CF3M 60358 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- Only for matching VALV 33
LB AARH) F316L 60194 Equ't conns. GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 182 GR. GA-E- VALV 01
F316L 60195 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- Only for Matching VALV 35
LB AARH) F316L 60196 flgd. 600# conns. GAT
Valve Gate 2 10 API 600 FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 01
LB AARH) CF3M 60197 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. GA-E- VALV 04
F316L 60255 GLB
Valve Globe 2 8 BS 1873 FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 04
LB AARH) CF3M 60256 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.11/MANUF. SW-F 800# FORGED ASTM A 182 GR. GA-E- STR
STD F316L 60639 WYE
Strainer Y-Type 2 2 ASME B16.5/MANUF. FLG 300 R.F. (125-250 CAST ASTM A 351 GR. GA-E- STR
STD LB AARH) CF3M 60640 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- BLR
LB AARH) F316L 60010
Drip Ring 2 10 SP TB.5011 WAFER 300 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- BLR
LB AARH) F316L 60010
Spectacle Blind 2 10 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- LNBDS
LB AARH) F316L 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010 BLD
Flange Blind 2 10 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010 BLD
Flange Welding Neck 2 10 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010 WNK
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:35 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- 45L
F316L 60010
45° Elbow Long Radius 2 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 45L
W WP316L 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- 90L
F316L 60010
90° Elbow Long Radius 2 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 90L
W WP316L 60010 LR
Reducer Concentric 3 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316L 60010 CON
2 8
Reducer Eccentric 3 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316L 60010 ECC
2 8
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- TEE
F316L 60010 STR
Tee Equal 2 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316L 60010 STR
Tee Reducing 3/4 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- TEE
F316L 60010 RED
1/2 1
Tee Reducing 3 10 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316L 60010 RED
2 8
Cap 2 10 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316L 60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- CAP
F316L 60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- CPL
F316L 60010
Coupling Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. GA-E- CPL
F316L 60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 182 GR. GA-E- PLG
F316L 60010 HEX
Sockolet 2 10 SP TB.5380 SW-F 3000# FORGED ASTM A 182 GR. GA-E- SOL
F316L 60010
1/2 1+1/2
Thredolet 2 10 SP TB.5380 THRD-F 3000# FORGED ASTM A 182 GR. GA-E- TOL
F316L 60010
1/2 1+1/2
Weldolet 6 10 SP TB.5004 BW FORGED ASTM A 182 GR. GA-E- WOL
F316L 60010
2 4
Gasket 1/2 10 ASME B16.20 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:36 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 312 TP 316L GA-E- XS NIPP
60010
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 312 TP 316L GA-E- XS NIPP
60010
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 312 TP 316L GA-E- XS NIPP
60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:39 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 33C Branch Table 33C
Branch 10 TE Branch
Size 8 TR TE S Sockolet
6 TR TR TE
TE Tee Equal
4 TR TR TR TE
TR Tee Reducing
3 W W TR TR TE
W Weldolet
2 W W W TR TR TE
1H S S S S S S TE
1 S S S S S S TR TE
TQ S S S S S S TR TR TE
H S S S S S S TR TR TR TE
10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:41 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI & ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:53 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 10 10 ASME B16.34/MANUF. FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB 36-SP-008 GA-E- VALV 61
Nozzle Type STD LB AARH) 60025 CHK
Pipe 1/2 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 24 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60477 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60478 on P&ID. BAL
Valve Ball Reducer Bore 2 4 API 6D FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 07
LB AARH) 60483 BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60313 CHK
Valve Check 2 24 API 594 WAFER 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60314 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 13
LB AARH) 60125 Equ't Nozzles GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60126 GAT
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for matching VALV 15
LB AARH) 60124 Flgd 600# Conns. GAT
Valve Gate 2 24 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60127 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60213 GLB
Valve Globe 2 8 BS 1873 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60214 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60612 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- STR
LB AARH) 60613 WYE
Drip Ring 1/2 1+1/2 SP TB.5011 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Drip Ring 2 24 SP TB.5011 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- BLR
LB AARH) 60011
Spacer & Blind 14 24 SP TB.5039 WAFER 300 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:55 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Blind 2 24 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 1/2 24 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" - 1 1/2" sizes FLG
LB AARH) 60011 only for mating to WNK
300# flanged conns.
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
1+1/2 20
Reducer Eccentric 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
1+1/2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
Cap 2 30 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 3/4 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1/2 1
Isolating Kit 1 1+1/2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
Isolating Kit 2 2 MANUFACTURE STD FLG 300 R.F. (125-250 GA-E-
LB AARH) 60018
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:56 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Union 1/2 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 24 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 6000# FORGED ASTM A 105 GA-E- TOL
60011
1/2 1+1/2
Weldolet 6 24 SP TB.5004 BW FORGED ASTM A 105 GA-E- WOL
60011
2 8
Gasket 1/2 24 ASME B16.20 FLG 300 R.F. (125-250 _ INCONEL 625 GA-E- 1/2" - 1 1/2" sizes GAS
LB AARH) SPIRAL 60012 only for mating to
WOUND/GRAPHITE flanged conns.
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1+1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 106 GR. B GA-E- NIPP
60011
1/2 1
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM A 106 GR. B GA-E- XXS NIPP
60011
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:18:59 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 33H Branch Table 33H
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:01 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:05 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:13 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.19 PL SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Pipe 2 8 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Pipe 10 24 ASME B36.19 BE E.F.W. ASTM A 358 GR. 316 GA-E- PIP
CL.1 60010
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- For use only if shown VALV 08
LB AARH) CF8M 60431 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- For use only if shown VALV 08
LB AARH) CF8M 60432 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 06
60310 CHK
Valve Check 2 24 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 06
LB AARH) CF8M 60319 CHK
Valve Double Block & 1/2 1/2 MANUFACTURE STD SW-F x THRD-F 800# FORGED ASTM A 182 GR. F316 GA-E- Use for Orifice Taps VALV 11
Bleed 60433 Only DBB
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Use for Inst. Conns. VALV 12
Bleed LB AARH) 60414 Only DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Use for PI conns. VALV 10
Bleed LB AARH) 60412 Only DBB
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- Threaded 1/2" NPT VALV 10
Bleed LB AARH) 60415 female, use for PI DBB
Conns. Only
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- VALV 03
LB AARH) 60120 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 01
60121 GAT
Valve Gate 2 24 API 600 FLG 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 01
LB AARH) CF8M 60131 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 04
60210 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 04
LB AARH) CF8M 60216 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 03
03 LB AARH) TP316L 60010 STS
Strainer Temporary Mesh 1+1/2 3 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316L 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 182 GR. F316 GA-E- STR
60609 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A 351 GR. GA-E- STR
LB AARH) CF8M 60627 WYE
Spacer & Blind 12 24 SP TB.5039 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PAC
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010
Flange Blind 1/2 24 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- 45L
60010
45° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 45L
W WP316 60010 LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- 90L
60010
90° Elbow Long Radius 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- 90L
W WP316 60010 LR
Reducer Concentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316 60010 CON
2 20
Reducer Eccentric 3 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- RED
W WP316 60010 ECC
2 20
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TEE
60010 STR
Tee Equal 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TEE
60010 RED
Tee Reducing 2 24 ASME B16.9 BW WROUGHT-S or ASTM A 403 GR. GA-E- TEE
W WP316 60010 RED
Cap 2 24 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316 60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CAP
60010
Coupling 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CPL
60010
Coupling Reducing 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- CPL
60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM A 182 GR. F316 GA-E- PLG
60010 HEX
Sockolet 2 24 SP TB.5380 SW-F 3000# FORGED ASTM A 182 GR. F316 GA-E- SOL
60010
1/2 1+1/2
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM A 182 GR. F316 GA-E- TOL
60010
1/2 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:16 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:19 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 35A Branch Table 35A
Branch 24 TE Branch
Size 20 TR TE S Sockolet
18 TR TR TE
TE Tee Equal
16 TR TR TR TE
TR Tee Reducing
14 TR TR TR TR TE
W Weldolet
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H S S S S S S S S S S S S TE
1 S S S S S S S S S S S S TR TE
TQ S S S S S S S S S S S S TR TR TE
H S S S S S S S S S S S S TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:21 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:24 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:30 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.19 PL SEAMLESS ASTM A 312 TP 316 GA-E- PIP
60010
Valve Check 1/2 1+1/2 BS 5352 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 06
60337 CHK
Valve Gate 1/2 1+1/2 API 602 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 01
60163 GAT
Valve Globe 1/2 1+1/2 BS 5352 BW 800# FORGED ASTM A 182 GR. F316 GA-E- VALV 04
60232 GLB
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 240 GR. GA-E- STR 05
05 LB AARH) TP316 60010 STS
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- LNBDS
LB AARH) 60010 PEC
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 BLD
Flange Welding Neck 1/2 1+1/2 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 182 GR. F316 GA-E- FLG
LB AARH) 60010 WNK
45° Elbow Long Radius 1/2 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 45L
WP316 60010 LR
90° Elbow Long Radius 1/2 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 90L
WP316 60010 LR
Reducer Concentric 3/4 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316 60010 CON
1/2 1
Reducer Eccentric 3/4 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316 60010 ECC
1/2 1
Tee Equal 1/2 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316 60010 RED
Cap 1/2 1+1/2 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316 60010
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/PTFE
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:34 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 35B Branch Table 35B
Branch 1H TE Branch
Size 1 TR TE TE Tee Equal
TQ TR TR TE
TR Tee Reducing
H TR TR TR TE
1H 1 TQ H
Run Size
3
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:38 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 10 10 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB 36-SP-012 GA-E- VALV 62
Nozzle Type STD LB AARH) 60025 CHK
Valve Check Non Slam 10 10 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB 36-SP-009 GA-E- VALV 61
Nozzle Type STD LB AARH) 60025 CHK
Valve Check Non Slam 12 12 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB 20-SP-013 GA-E- VALV 61
Nozzle Type STD LB AARH) 60025 CHK
Pipe 1 1+1/2 ASME B36.10 PL SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Pipe 2 18 ASME B36.10 BE SEAMLESS ASTM A 106 GR. B GA-E- PIP
60011
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60434 on P&ID. BAL
Valve Ball Full Bore 6 18 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- For use only if shown VALV 08
LB AARH) 60435 on P&ID. BAL
Valve Ball Reducer Bore 6 18 API 6D FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 07
LB AARH) 60484 BAL
Valve Check 1 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 06
60313 CHK
Valve Check 2 18 API 594 WAFER 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60322 CHK
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- Threaded 1/2" NPT VALV 10
Bleed LB AARH) 60464 female, Use for PI DBB
conns. Only
Valve Double Block & 1 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 12
Bleed LB AARH) 60466 DBB
Valve Gate 1 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- VALV 03
LB AARH) 60124 GAT
Valve Gate 1 1+1/2 API 602 SW-F 800# FORGED ASTM A 105 GA-E- VALV 01
60126 GAT
Valve Gate 2 18 API 600 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 03
LB AARH) 60132 GAT
Valve Globe 1 1+1/2 BS 5352 SW-F 800# FORGED ASTM A 105 GA-E- VALV 04
60213 GLB
Valve Globe 2 10 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60217 GLB
Strainer Y-Type 1 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM A 105 GA-E- STR
60612 WYE
Spacer & Blind 12 18 SP TB.5039 WAFER 600 R.F. (125-250 FROM PLATE ASTM A 516 GRADE GA-E- LNBDS
LB AARH) 70 60011 PAC
Spectacle Blind 1 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) 60011 PEC
Flange 1 1+1/2 ASME B16.5 FLG x SW-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Blind 1 18 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) 60011 BLD
Flange Welding Neck 1 18 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM A 105 GA-E- 1- 1 1/2" sizes only FLG
LB AARH) 60011 for mating to 600# WNK
flanged conns.
45° Elbow 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 45L
60011
45° Elbow Long Radius 2 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 45L
W 60011 LR
90° Elbow 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- 90L
60011
90° Elbow Long Radius 2 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- 90L
W 60011 LR
Reducer Concentric 3 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 CON
2 16
Reducer Eccentric 3 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- RED
W 60011 ECC
2 16
Tee Equal 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 STR
Tee Equal 2 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 STR
Tee Reducing 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- TEE
60011 RED
Tee Reducing 3 18 ASME B16.9 BW WROUGHT-S or ASTM A 234 GR. WPB GA-E- TEE
W 60011 RED
2 16
Cap 2 18 ASME B16.9 BW WROUGHT-S ASTM A 234 GR. WPB GA-E- CAP
60011
Cap Female 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CAP
60011
Coupling 1 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
Coupling Reducing 1+1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 105 GA-E- CPL
60011
1 1
Isolating Kit 1 2 MANUFACTURE STD FLG 600 R.F. (125-250 GA-E-
LB AARH) 60018
Plug Hex Head 1 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 105 GA-E- PLG
60011 HEX
Union 1 1+1/2 MANUFACTURE STD SW-F 6000# FORGED ASTM A 105 GA-E- UNN
60011
Sockolet 2 18 SP TB.5380 SW-F 6000# FORGED ASTM A 105 GA-E- SOL
60011
1 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:49 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:53 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 35H Branch Table 35H
Branch 18 TE Branch
Size 16 TR TE S Sockolet
14 TR TR TE
TE Tee Equal
12 TR TR TR TE
TR Tee Reducing
10 TR TR TR TR TE
W Weldolet
8 TR TR TR TR TR TE
6 W TR TR TR TR TR TE
4 W W W W TR TR TR TE
3 W W W W W W TR TR TE
2 W W W W W W W TR TR TE
1H S S S S S S S S S S TE
1 S S S S S S S S S S TR TE
18 16 14 12 10 8 6 4 3 2 1H 1
Run Size
Sizes translation 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:55 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:19:59 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:08 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 1+1/2 ASME B36.19 PL SEAMLESS ASTM A 312 TP 316L GA-E- PIP
60010
Pipe 2 8 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316L GA-E- PIP
60010
Pipe 10 16 ASME B36.19 BE E.F.W. ASTM A 358 GR. GA-E- PIP
316L CL.1 60010
Valve Check 1/2 1+1/2 BS 5352 SW-F 1500 FORGED ASTM A 182 GR. GA-E- VALV 06
LB F316L 60359 CHK
Valve Check 2 2 BS 1868 FLG 1500 Ring Joint CAST ASTM A 351 GR. GA-E- VALV 06
LB CF3M 60360 CHK
Valve Check 3 16 API 594 WAFER 900 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 06
LB AARH) CF3M 60361 CHK
Valve Double Block & 2 2 MANUFACTURE STD FLG x FLG 900 Ring Joint CAST ASTM A 351 GR. GA-E- VALV 10
Bleed LB CF3M 60486 DBB
Valve Gate 1/2 1+1/2 API 602 SW-F 1500 FORGED ASTM A 182 GR. GA-E- VALV 01
LB F316L 60517 GAT
Valve Gate 2 2 ASME B16.34 FLG 1500 Ring Joint CAST ASTM A 351 GR. GA-E- VALV 01
LB CF3M 60518 GAT
Valve Gate 3 16 ASME B16.34 FLG 900 R.F. (125-250 CAST ASTM A 351 GR. GA-E- VALV 01
LB AARH) CF3M 60519 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 1500 FORGED ASTM A 182 GR. GA-E- VALV 04
LB F316L 60257 GLB
Valve Globe 2 2 BS 1873 FLG 1500 Ring Joint CAST ASTM A 351 GR. GA-E- VALV 04
LB CF3M 60258 GLB
Valve Globe 3 8 BS 1873 FLG 900 Ring Joint CAST ASTM A 351 GR. GA-E- VALV 04
LB CF3M 60259 GLB
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 1500 FORGED ASTM A 182 GR. GA-E- STR
LB F316L 60642 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 1500 R.F. (125-250 CAST ASTM A 351 GR. GA-E- STR
LB AARH) CF3M 60643 WYE
Spacer & Blind 10 16 SP TB.5039 WAFER 900 Ring Joint FORGED ASTM A 182 GR. LNBDS
LB F316L PAC
Spectacle Blind 1/2 2 SP TB.5038 WAFER 1500 Ring Joint FORGED ASTM A 182 GR. LNBDS
LB F316L PEC
Spectacle Blind 3 8 SP TB.5038 WAFER 900 Ring Joint FORGED ASTM A 182 GR. GA-E- LNBDS
LB F316L 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x SW-F 1500 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010
Flange Blind 1/2 2 ASME B16.5 FLG 1500 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010 BLD
Flange Blind 3 16 ASME B16.5 FLG 900 Ring Joint FORGED ASTM A 182 GR. GA-E- FLG
LB F316L 60010 BLD
Flange Welding Neck 2 2 ASME B16.5 FLG x BW 1500 R.F. (125-250 FORGED ASTM A 182 GR. GA-E- FLG
LB AARH) F316L 60010 WNK
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:10 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Welding Neck 3 16 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM A 182 GR. FLG
LB F316L WNK
45° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- 45L
F316L 60010
45° Elbow Long Radius 2 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 45L
WP316L 60010 LR
45° Elbow Long Radius 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. 45L
WP316L LR
90° Elbow 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- 90L
F316L 60010
90° Elbow Long Radius 2 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 90L
WP316L 60010 LR
90° Elbow Long Radius 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. 90L
WP316L LR
Reducer Concentric 3 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316L 60010 CON
2 6
Reducer Concentric 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. RED
WP316L CON
2 14
Reducer Eccentric 3 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316L 60010 ECC
2 6
Reducer Eccentric 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. RED
WP316L ECC
2 14
Tee Equal 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- TEE
F316L 60010 STR
Tee Equal 2 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316L 60010 STR
Tee Equal 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. GA-E- TEE
WP316L 60010 STR
Tee Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- TEE
F316L 60010 RED
1/2 1
Tee Reducing 2 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316L 60010 RED
2 6
Tee Reducing 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. TEE
WP316L RED
2 14
Cap 2 8 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316L 60010
Cap 10 16 ASME B16.9 BW WROUGHT-W ASTM A 403 GR. GA-E- CAP
WP316L 60010
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- CAP
F316L 60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:12 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Coupling 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- CPL
F316L 60010
Coupling Reducing 1/2 1+1/2 ASME B16.11 SW-F 6000# FORGED ASTM A 182 GR. GA-E- CPL
F316L 60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 6000# FORGED ASTM A 182 GR. GA-E- PLG
F316L 60010 HEX
Sockolet 2 16 SP TB.5380 SW-F 6000# FORGED ASTM A 182 GR. GA-E- SOL
F316L 60010
1/2 1+1/2
Thredolet 2 16 SP TB.5380 THRD-F 6000# FORGED ASTM A 182 GR. GA-E- TOL
F316L 60010
1/2 1+1/2
Weldolet 6 16 SP TB.5004 BW FORGED ASTM A 182 GR. GA-E- WOL
F316L 60010
2 4
Gasket 1/2 2 ASME B16.20 FLG 1500 Ring Joint _ STEEL 18/8/2 - AISI GA-E- GAS
LB 316 HB 160 60012
Gasket 3 16 ASME B16.20 FLG 900 Ring Joint _ STEEL 18/8/2 - AISI GA-E- GAS
LB 316 HB 160 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM A 312 TP 316L GA-E- XS NIPP
60010
Nipple Reducing 1/2 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM A 312 TP 316L GA-E- XS NIPP
60010
1/2 1
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:16 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 36B Branch Table 36B
Branch 16 TE Branch
Size 14 TR TE S Sockolet
12 TR TR TE
TE Tee Equal
10 TR TR TR TE
TR Tee Reducing
8 TR TR TR TR TE
W Weldolet
6 TR TR TR TR TR TE
4 W W W TR TR TR TE
3 W W W W W TR TR TE
2 W W W W W W TR TR TE
1H S S S S S S S S TR TE
1 S S S S S S S S TR TR TE
TQ S S S S S S S S TR TR TR TE
H S S S S S S S S S TR TR TR TE
16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:17 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI & ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:27 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 16 16 ASME B16.34/MANUF. BW CAST ASTM A 351 GR. 36-SP-004 GA-E- VALV 61
Nozzle Type STD CF3M 60025 CHK
Pipe 3 20 ASME B36.19 BE SEAMLESS ASTM A 312 TP 316L GA-E- PIP
60010
Valve Check 14 20 MANUFACTURE STD BW 2500 CAST ASTM A 351 GR. GA-E- VALV 06
LB CF3M 60364 CHK
45° Elbow Long Radius 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 45L
WP316L 60010 LR
90° Elbow Long Radius 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- 90L
WP316L 60010 LR
Reducer Concentric 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316L 60010 CON
Reducer Eccentric 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- RED
WP316L 60010 ECC
Tee Equal 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316L 60010 STR
Tee Reducing 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- TEE
WP316L 60010 RED
Cap 3 20 ASME B16.9 BW WROUGHT-S ASTM A 403 GR. GA-E- CAP
WP316L 60010
Weldolet 3 20 SP TB.5004 BW FORGED ASTM A 182 GR. GA-E- WOL
F316L 60010
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 15:50:29 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 38A Branch Table 38A
Branch 20 TE Branch
Size 16 TR TE TE Tee Equal
14 TR TR TE
TR Tee Reducing
12 TR TR TR TE
W Weldolet
4 W W W W TE
3 W W W W TR TE
2 W W W W TR TR TE
20 16 14 12 4 3 2
Run Size
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:36 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:43 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 3 ASME B36.19 BE SEAMLESS ASTM B 444 GR. GA-E- PIP
N06625 60010
Pipe 4 24 ASME B36.19 BE E.F.W. ASTM B705 UNS GA-E- PIP
N06625 60010
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 06
N06625 60351 CHK
Valve Check 2 24 API 594 WAFER 150 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 06
LB AARH) 60352 CHK
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 01
N06625 60154 GAT
Valve Gate 2 24 API 600 FLG 150 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 01
LB AARH) 60187 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 04
N06625 60225 GLB
Valve Globe 2 8 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 04
LB AARH) 60250 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 03
03 LB AARH) N06625 60010 STS
Strainer Temporary Mesh 1+1/2 1+1/2 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 05
05 LB AARH) N06625 60010 STS
Strainer Temporary Mesh 2 3 SP TB.5007 WAFER 150 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 05
05 LB AARH) N06625 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM B 564 GR. GA-E- STR
N06625 60632 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 150 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- STR
LB AARH) 60633 WYE
Spacer & Blind 14 24 SP TB.5039 WAFER 150 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N06625 60010 PAC
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N06625 60010 PEC
Spectacle Blind 2 12 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N06625 60010 PEC
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 BLD
Flange Blind 2 24 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 BLD
Flange Welding Neck 1/2 1+1/2 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 WNK
Flange Welding Neck 2 24 ASME B16.5 FLG x BW 150 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 WNK
45° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 45L
WPNCMC (UNS 60010 LR
N06625)
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:44 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
45° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 45L
W WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 90L
WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 90L
W WPNCMC (UNS 60010 LR
N06625)
Reducer Concentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 CON
1/2 2
N06625)
Reducer Concentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 CON
1/2 20
N06625)
Reducer Eccentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 ECC
1/2 2
N06625)
Reducer Eccentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 ECC
1/2 20
N06625)
Tee Equal 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 STR
N06625)
Tee Equal 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 STR
N06625)
Tee Reducing 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 RED
1/2 2
N06625)
Tee Reducing 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 RED
1/2 20
N06625)
Cap 1/2 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- CAP
W WPNCMC (UNS 60010
N06625)
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM B 564 GR. GA-E- PLG
N06625 60010 HEX
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM B 564 GR. GA-E- TOL
N06625 60010
1/2 1+1/2
Weldolet 2 24 SP TB.5004 BW FORGED ASTM B 564 GR. GA-E- WOL
N06625 60010
1/2 8
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:46 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Gasket 2 24 ASME B16.20 FLG 150 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60625
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM B 444 GR. GA-E- NIPP
N06625 60010
1/2 1+1/2
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM B 444 GR. GA-E- NIPP
N06625 60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:49 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 51A Branch Table 51A
Branch 24 TE Branch
Size 20 TR TE TE Tee Equal
18 TR TR TE
TR Tee Reducing
16 TR TR TR TE
W Weldolet
14 TR TR TR TR TE
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H W W W W W W W W W W W W TE
1 W W W W W W W W W W W W TR TE
TQ W W W W W W W W W W W W TR TR TE
H W W W W W W W W W W W W TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:20:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:01 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 6 ASME B36.19 BE SEAMLESS ASTM B423 GR. GA-E- PIP
UNS08825 60010
Pipe 8 16 ASME B36.19 BE E.F.W. ASTM B705 GR. GA-E- PIP
UNS08825 60010
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 06
N06625 60330 CHK
Valve Check 2 16 API 594 WAFER 300 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 06
LB AARH) 60353 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 300 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- VALV 33
LB AARH) N06625 60188 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 01
N06625 60154 GAT
Valve Gate 2 16 API 600 FLG 300 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 01
LB AARH) 60189 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 04
N06625 60225 GLB
Valve Globe 2 8 BS 1873 FLG 300 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 04
LB AARH) 60251 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 300 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 03
03 LB AARH) N06625 60010 STS
Strainer Temporary Mesh 1+1/2 3 SP TB.5007 WAFER 300 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 05
05 LB AARH) N06625 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM B 564 GR. GA-E- STR
N06625 60617 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 300 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- STR
LB AARH) 60635 WYE
Spacer & Blind 12 16 SP TB.5039 WAFER 300 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N08825 60010 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 300 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N08825 60010 PEC
Flange Blind 1/2 16 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N08825 60010 BLD
Flange Welding Neck 1/2 16 ASME B16.5 FLG x BW 300 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N08825 60010 WNK
45° Elbow Long Radius 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 45L
WPNICMC (UNS 60010 LR
N08825)
45° Elbow Long Radius 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 45L
W WPNICMC (UNS 60010 LR
N08825)
90° Elbow Long Radius 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 90L
WPNICMC (UNS 60010 LR
N08825)
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:03 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
90° Elbow Long Radius 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 90L
W WPNICMC (UNS 60010 LR
N08825)
Reducer Concentric 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNICMC (UNS 60010 CON
1/2 4
N08825)
Reducer Concentric 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNICMC (UNS 60010 CON
1/2 14
N08825)
Reducer Eccentric 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNICMC (UNS 60010 ECC
1/2 4
N08825)
Reducer Eccentric 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNICMC (UNS 60010 ECC
1/2 14
N08825)
Tee Equal 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNICMC (UNS 60010 STR
N08825)
Tee Equal 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNICMC (UNS 60010 STR
N08825)
Tee Reducing 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNICMC (UNS 60010 RED
1/2 2
N08825)
Tee Reducing 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNICMC (UNS 60010 RED
1/2 14
N08825)
Cap 1/2 16 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- CAP
WPNICMC (UNS 60010
N08825)
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM B 564 GR. GA-E- CAP
N08825 60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM B 564 GR. GA-E- PLG
N08825 60010 HEX
Thredolet 2 16 SP TB.5380 THRD-F 3000# FORGED ASTM B 564 GR. GA-E- TOL
N08825 60010
1/2 1+1/2
Weldolet 2 16 SP TB.5004 BW FORGED ASTM B 564 GR. GA-E- WOL
N08825 60010
1/2 8
Gasket 1/2 16 ASME B16.20 FLG 300 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM B423 GR. GA-E- XS NIPP
UNS08825 60625
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:05 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM B423 GR. GA-E- XS NIPP
UNS08825 60010
1/2 1+1/2
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM B423 GR. GA-E- XS NIPP
UNS08825 60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:09 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 53A Branch Table 53A
Branch 16 TE Branch
Size 14 TR TE I Pipe to Pipe
12 TR TR TE
S Sockolet
10 I TR TR TE
TE Tee Equal
8 I I TR TR TE
TR Tee Reducing
6 I I I TR TR TE
4 I I I I TR TR TE
3 I I I I I TR TR TE
2 I I I I I I TR TR TE
1H S S S S S S S S TR TE
1 S S S S S S S S TR TR TE
TQ S S S S S S S S TR TR TR TE
H S S S S S S S S S TR TR TR TE
16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:10 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:15 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Valve Check Non Slam 10 10 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 36-SP-010 GA-E- VALV 61
Nozzle Type STD LB AARH) 60025 CHK
Valve Check Non Slam 10 10 ASME B16.34/MANUF. FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 36-SP-011 GA-E- VALV 62
Nozzle Type STD LB AARH) 60025 CHK
Pipe 1/2 6 ASME B36.19 BE SEAMLESS ASTM B423 GR. GA-E- PIP
UNS08825 60010
Pipe 8 16 ASME B36.19 BE E.F.W. ASTM B705 GR. GA-E- PIP
UNS08825 60010
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- For use only if shown VALV 08
LB AARH) 60449 on P&ID. BAL
Valve Ball Full Bore 6 16 API 6D FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- For use only if shown VALV 08
LB AARH) 60450 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 06
N06625 60330 CHK
Valve Check 2 16 API 594 WAFER 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 06
LB AARH) 60331 CHK
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- VALV 35
LB AARH) N06625 60158 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 01
N06625 60154 GAT
Valve Gate 2 16 API 600 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 01
LB AARH) 60155 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 04
N06625 60225 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 04
LB AARH) 60226 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 03
03 LB AARH) N06625 60010 STS
Strainer Temporary Mesh 1+1/2 3 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 05
05 LB AARH) N06625 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM B 564 GR. GA-E- STR
N06625 60617 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- STR
LB AARH) 60618 WYE
Spacer & Blind 12 16 SP TB.5039 WAFER 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N08825 60010 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N08825 60010 PEC
Flange Blind 1/2 16 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N08825 60010 BLD
Flange Welding Neck 1/2 16 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N08825 60010 WNK
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:24 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
45° Elbow Long Radius 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 45L
WPNICMC (UNS 60010 LR
N08825)
45° Elbow Long Radius 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 45L
W WPNICMC (UNS 60010 LR
N08825)
90° Elbow Long Radius 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 90L
WPNICMC (UNS 60010 LR
N08825)
90° Elbow Long Radius 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 90L
W WPNICMC (UNS 60010 LR
N08825)
Reducer Concentric 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNICMC (UNS 60010 CON
1/2 4
N08825)
Reducer Concentric 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNICMC (UNS 60010 CON
1/2 14
N08825)
Reducer Eccentric 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNICMC (UNS 60010 ECC
1/2 4
N08825)
Reducer Eccentric 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNICMC (UNS 60010 ECC
1/2 14
N08825)
Tee Equal 1/2 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNICMC (UNS 60010 STR
N08825)
Tee Equal 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNICMC (UNS 60010 STR
N08825)
Tee Reducing 3/4 6 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNICMC (UNS 60010 RED
1/2 4
N08825)
Tee Reducing 8 16 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNICMC (UNS 60010 RED
1/2 14
N08825)
Cap 1/2 16 ASME B16.9 BW WROUGHT-S ASTM B366- CAP
WPNICMC (UNS
N08825)
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM B 564 GR. GA-E- CAP
N08825 60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM B 564 GR. GA-E- PLG
N08825 60010 HEX
Thredolet 2 16 SP TB.5380 THRD-F 3000# FORGED ASTM B 564 GR. GA-E- TOL
N08825 60010
1/2 1+1/2
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:25 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:28 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 55A Branch Table 55A
Branch 16 TE Branch
Size 14 TR TE I Pipe to Pipe
12 TR TR TE
S Sockolet
10 I TR TR TE
TE Tee Equal
8 I I TR TR TE
TR Tee Reducing
6 I I I TR TR TE
4 I I I I TR TR TE
3 I I I I I TR TR TE
2 I I I I I I TR TR TE
1H S S S S S S S S TR TE
1 S S S S S S S S TR TR TE
TQ S S S S S S S S TR TR TR TE
H S S S S S S S S S TR TR TR TE
16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:30 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:33 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:40 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 3 ASME B36.19 BE SEAMLESS ASTM B 444 GR. GA-E- PIP
N06625 60010
Pipe 4 24 ASME B36.19 BE E.F.W. ASTM B705 UNS GA-E- PIP
N06625 60010
Valve Ball Full Bore 2 4 API 6D FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- For use only if shown VALV 08
LB AARH) 60449 on P&ID. BAL
Valve Ball Full Bore 6 24 API 6D FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- For use only if shown VALV 08
LB AARH) 60450 on P&ID. BAL
Valve Check 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 06
N06625 60330 CHK
Valve Check 2 24 API 594 WAFER 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 06
LB AARH) 60331 CHK
Valve Double Block & 1/2 1/2 MANUFACTURE STD SW-F x THRD-F 800# FORGED ASTM B 564 GR. GA-E- Use for Orifice Taps VALV 11
Bleed N06625 60446 Only DBB
Valve Double Block & 1/2 2 MANUFACTURE STD FLG x FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- Use for Inst. Conns. VALV 12
Bleed LB AARH) N06625 60445 Only DBB
Valve Double Block & 1/2 1/2 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- Use for PI conns. VALV 10
Bleed LB AARH) N06625 60447 Only DBB
Valve Double Block & 1 1 MANUFACTURE STD FLG x THRD-F 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- Threaded 1/2" NPT VALV 10
Bleed LB AARH) N06625 60448 female, use for PI DBB
Conns. Only
Valve Gate 1/2 1+1/2 API 602 FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- VALV 03
LB AARH) N06625 60158 GAT
Valve Gate 1/2 1+1/2 API 602 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 01
N06625 60154 GAT
Valve Gate 2 24 API 600 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 01
LB AARH) 60155 GAT
Valve Globe 1/2 1+1/2 BS 5352 SW-F 800# FORGED ASTM B 564 GR. GA-E- VALV 04
N06625 60225 GLB
Valve Globe 2 8 BS 1873 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- VALV 04
LB AARH) 60226 GLB
Strainer Temporary Mesh 4 12 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 03
03 LB AARH) N06625 60010 STS
Strainer Temporary Mesh 1+1/2 3 SP TB.5007 WAFER 600 R.F. (125-250 FROM PLATE ASTM B 443 GR. GA-E- STR 05
05 LB AARH) N06625 60010 STS
Strainer Y-Type 1/2 1+1/2 ASME B16.34 SW-F 800# FORGED ASTM B 564 GR. GA-E- STR
N06625 60617 WYE
Strainer Y-Type 2 2 ASME B16.34 FLG 600 R.F. (125-250 CAST ASTM A494-CY-40 GA-E- STR
LB AARH) 60618 WYE
Spacer & Blind 12 24 SP TB.5039 WAFER 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N06625 60010 PAC
Spectacle Blind 1/2 10 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- LNBDS
LB AARH) N06625 60010 PEC
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:42 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Blind 1/2 24 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 BLD
Flange Welding Neck 1/2 24 ASME B16.5 FLG x BW 600 R.F. (125-250 FORGED ASTM B 564 GR. GA-E- FLG
LB AARH) N06625 60010 WNK
45° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 45L
WPNCMC (UNS 60010 LR
N06625)
45° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 45L
W WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 90L
WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 90L
W WPNCMC (UNS 60010 LR
N06625)
Reducer Concentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 CON
1/2 2
N06625)
Reducer Concentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 CON
1/2 20
N06625)
Reducer Eccentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 ECC
1/2 2
N06625)
Reducer Eccentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 ECC
1/2 20
N06625)
Tee Equal 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 STR
N06625)
Tee Equal 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 STR
N06625)
Tee Reducing 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 RED
1/2 2
N06625)
Tee Reducing 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 RED
1/2 20
N06625)
Cap 1/2 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- CAP
W WPNCMC (UNS 60010
N06625)
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM B 564 GR. GA-E- CAP
N06625 60010
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:43 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM B 564 GR. GA-E- PLG
N06625 60010 HEX
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM B 564 GR. GA-E- TOL
N06625 60010
1/2 1+1/2
Weldolet 2 24 SP TB.5004 BW FORGED ASTM B 564 GR. GA-E- WOL
N06625 60010
1/2 8
Gasket 1/2 24 ASME B16.20 FLG 600 R.F. (125-250 _ INCONEL 625 GA-E- GAS
LB AARH) SPIRAL 60012
WOUND/GRAPHITE
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60625
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60010
1/2 1+1/2
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60010
1/2 1+1/2
4
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:47 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 55B Branch Table 55B
Branch 24 TE Branch
Size 20 TR TE TE Tee Equal
18 TR TR TE
TR Tee Reducing
16 TR TR TR TE
W Weldolet
14 TR TR TR TR TE
12 TR TR TR TR TR TE
10 TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H W W W W W W W W W W W W TE
1 W W W W W W W W W W W W TR TE
TQ W W W W W W W W W W W W TR TR TE
H W W W W W W W W W W W W TR TR TR TE
24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 24=24
5
Snamprogetti S.p.A. PIPING CLASS NOTE PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:48 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Note: 1) ONLY USE FOR PI& ORIFICE CONNECTIONS WHERE IT IS NOT NECESSARY TO USE DIAPHRAGM SEALED INSTRUMENTS, I.E., NOT IN H2S SERVICE.
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:52 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:21:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:01 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 3 ASME B36.19 BE SEAMLESS ASTM B 444 GR. GA-E- PIP
N06625 60010
Pipe 4 24 ASME B36.19 BE E.F.W. ASTM B705 UNS GA-E- PIP
N06625 60010
Pipe 30 30 ASME B36.10 BE S.A.W. API 5L GR. X60 Inconel 625 GA-E- PIP
cladded 60020
Valve Ball Full Bore 2 2 API 6D FLG 1500 Ring Joint CAST ASTM A494-CY-40 GA-E- VALV 08
LB 60444 BAL
Valve Ball Full Bore 3 20 API 6D FLG 900 Ring Joint CAST ASTM A494-CY-40 GA-E- VALV 08
LB 60451 BAL
Valve Check 1/2 2 BS 5352 BW 1500 FORGED ASTM B 564 GR. GA-E- VALV 06
LB N06625 60332 CHK
Valve Check 3 24 API 594 LUG 900 Ring Joint CAST ASTM A494-CY-40 GA-E- VALV 06
LB 60333 CHK
Valve Double Block & 2 2 MANUFACTURE STD FLG x FLG 1500 Ring Joint FORGED ASTM B 564 GR. GA-E- Use for Inst. Conns. VALV 12
Bleed LB N06625 60452 Only DBB
Valve Gate 1/2 2 API 602 BW 1500 FORGED ASTM B 564 GR. GA-E- VALV 01
LB N06625 60156 GAT
Valve Gate 3 24 ASME B16.34 BW 900 CAST ASTM A494-CY-40 GA-E- VALV 01
LB 60157 GAT
Valve Globe 1/2 2 BS 5352 FLG 1500 Ring Joint FORGED ASTM B 564 GR. GA-E- VALV 04
LB N06625 60227 GLB
Valve Globe 3 6 BS 1873 FLG 900 Ring Joint CAST ASTM A494-CY-40 GA-E- VALV 04
LB 60228 GLB
Strainer Temporary Mesh 3 12 SP TB.5007 WAFER 900 Ring Joint FROM PLATE ASTM B 443 GR. GA-E- STR 03
03 LB N06625 60010 STS
Strainer Y-Type 1/2 2 MANUFACTURE STD BW 1500 FORGED ASTM B 564 GR. GA-E- STR
LB N06625 60619 WYE
Spacer & Blind 10 24 SP TB.5039 WAFER 900 Ring Joint FORGED ASTM B 564 GR. GA-E- LNBDS
LB N06625 60010 PAC
Spectacle Blind 1/2 2 SP TB.5038 WAFER 1500 Ring Joint FORGED ASTM B 564 GR. GA-E- LNBDS
LB N06625 60010 PEC
Spectacle Blind 3 8 SP TB.5038 WAFER 900 Ring Joint FORGED ASTM B 564 GR. GA-E- LNBDS
LB N06625 60010 PEC
Flange Blind 1/2 2 ASME B16.5 FLG 1500 Ring Joint FORGED ASTM B 564 GR. GA-E- FLG
LB N06625 60010 BLD
Flange Blind 3 24 ASME B16.5 FLG 900 Ring Joint FORGED ASTM B 564 GR. GA-E- FLG
LB N06625 60010 BLD
Flange Blind 30 30 ASME B16.47 SERIES A FLG 900 Ring Joint FORGED ASTM A 694 F60 Inconel 625 GA-E- FLG
LB cladded 60020 BLD
Flange Welding Neck 1/2 2 ASME B16.5 FLG x BW 1500 Ring Joint FORGED ASTM B 564 GR. GA-E- FLG
LB N06625 60010 WNK
Flange Welding Neck 3 24 ASME B16.5 FLG x BW 900 Ring Joint FORGED ASTM B 564 GR. GA-E- FLG
LB N06625 60010 WNK
3
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:03 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Flange Welding Neck 30 30 ASME B16.47 SERIES A FLG x BW 900 Ring Joint FORGED ASTM A 694 F60 Inconel 625 GA-E- FLG
LB cladded 60020 WNK
45° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 45L
WPNCMC (UNS 60010 LR
N06625)
45° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 45L
W WPNCMC (UNS 60010 LR
N06625)
45° Elbow Long Radius 30 30 ASME B16.9 BW WROUGHT-W ASTM A860 WPHY60 Inconel 625 GA-E- 45L
cladded 60020 LR
90° Elbow Long Radius 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- 90L
WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- 90L
W WPNCMC (UNS 60010 LR
N06625)
90° Elbow Long Radius 30 30 ASME B16.9 BW WROUGHT-W ASTM A860 WPHY60 Inconel 625 GA-E- 90L
cladded 60020 LR
Reducer Concentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 CON
1/2 2
N06625)
Reducer Concentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 CON
1/2 20
N06625)
Reducer Concentric 30 30 ASME B16.9 BW WROUGHT-W ASTM A860 WPHY60 Inconel 625 GA-E- RED
cladded 60020 CON
20 20
Reducer Eccentric 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- RED
WPNCMC (UNS 60010 ECC
1/2 2
N06625)
Reducer Eccentric 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- RED
W WPNCMC (UNS 60010 ECC
1/2 20
N06625)
Reducer Eccentric 30 30 ASME B16.9 BW WROUGHT-W ASTM A860 WPHY60 Inconel 625 GA-E- RED
cladded 60020 ECC
20 20
Tee Equal 1/2 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 STR
N06625)
Tee Equal 4 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 STR
N06625)
Tee Equal 30 30 ASME B16.9 BW WROUGHT-W ASTM A860 WPHY60 Inconel 625 GA-E- TEE
cladded 60020 STR
4
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:04 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 3/4 3 ASME B16.9 BW WROUGHT-S ASTM B366- GA-E- TEE
WPNCMC (UNS 60010 RED
1/2 2
N06625)
Tee Reducing 4 30 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- TEE
W WPNCMC (UNS 60010 RED
1/2 28
N06625)
Cap 1/2 24 ASME B16.9 BW WROUGHT-S or ASTM B366- GA-E- CAP
W WPNCMC (UNS 60010
N06625)
Cap Female 1/2 1+1/2 ASME B16.11 SW-F 3000# FORGED ASTM B 564 GR. GA-E- CAP
N06625 60010
Plug Hex Head 1/2 1+1/2 ASME B16.11 THRD-M 3000# FORGED ASTM B 564 GR. GA-E- PLG
N06625 60010 HEX
Thredolet 2 24 SP TB.5380 THRD-F 3000# FORGED ASTM B 564 GR. GA-E- TOL
N06625 60010
1/2 1+1/2
Weldolet 2 24 SP TB.5004 BW FORGED ASTM B 564 GR. GA-E- WOL
N06625 60010
1/2 8
Gasket 1/2 2 ASME B16.20 FLG 1500 Ring Joint _ INCONEL 625 GA-E- GAS
LB 60012
Gasket 3 24 ASME B16.20 FLG 900 Ring Joint _ INCONEL 625 GA-E- GAS
LB 60012
Gasket 30 30 ASME B16.20/ASME FLG 900 Ring Joint _ INCONEL 625 GA-E- GAS
B16.47 SERIE A LB 60012
Nipple L=100 mm 1/2 1+1/2 SP TB.5383 B = THRD-M - PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60625
Nipple Reducing 3/4 1+1/2 SP TB.5382 C = PL > PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60010
1/2 1+1/2
Nipple Reducing 2 2 SP TB.5382 C = BE > PL SEAMLESS ASTM B 444 GR. GA-E- XS NIPP
N06625 60010
1/2 1+1/2
5
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:09 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 56B Branch Table 56B
Branch 30 TE Branch
Size 28 TR TE Tee Equal
26 TR
TR Tee Reducing
24 TR TE
W Weldolet
22 TR
20 TR TR TE
18 TR TR TR TE
16 TR TR TR TR TE
14 TR TR TR TR TR TE
12 TR TR TR TR TR TR TE
10 TR TR TR TR TR TR TR TE
8 W TR TR TR TR TR TR TE
6 W W W TR TR TR TR TR TE
4 W W W W W W TR TR TR TE
3 W W W W W W W W TR TR TE
2 W W W W W W W W W TR TR TE
1H W W W W W W W W W W W W TE
1 W W W W W W W W W W W W TR TE
TQ W W W W W W W W W W W W TR TR TE
H W W W W W W W W W W W W TR TR TR TE
30 24 20 18 16 14 12 10 8 6 4 3 2 1H 1 TQ H
Run Size
Sizes translation H=1/2, TQ=3/4, 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18, 20=20, 22=22, 24=24, 26=26, 28=28, 30=30
6
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:14 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Base Material 11b CARBON STEEL & GALV. C.S. Applicable through
Min Max
Rating 0150 150 LB
Temperature °C -29.0 100.0
Finish RF0 R.F. (125-250 AARH)
Pressure BAR 0 0
Heat Treatment
Control level Chgd Mod
Note THREADED PIPE CONSTRUCTION ALL SIZES
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:20 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Pipe 1/2 4 ASME B36.10 THRD-M / COUPLED SEAMLESS ASTM A 53 GR. B GA-E- PIP
Galvanized 60010
Valve Ball Full Bore 1/2 2 MSS SP-80 THRD-F 200 CAST BRONZE GA-E- For use only if shown VALV 08
LB 60436 on P&ID. BAL
Valve Check 1/2 2 MSS SP-80 THRD-F 200 CAST ASTM B 62 GA-E- VALV 06
LB 60323 CHK
Valve Check 3 4 API 594 WAFER 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 06
LB AARH) 60324 CHK
Valve Gate 1/2 2 MSS SP-80 THRD-F 200 CAST ASTM B 62 GA-E- VALV 01
LB 60133 GAT
Valve Gate 2 2 API 600 FLG 300 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- Only for Press. Taps VALV 10
LB AARH) 60199 on Equ't GAT
Valve Gate 3 4 API 600 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 01
LB AARH) 60134 GAT
Valve Globe 1/2 2 MSS SP-80 THRD-F 200 CAST ASTM B 62 GA-E- VALV 04
LB 60218 GLB
Valve Globe 3 4 BS 1873 FLG 150 R.F. (125-250 CAST ASTM A 216 GR. WCB GA-E- VALV 04
LB AARH) 60219 GLB
Strainer Y-Type 1/2 2 ASME B16.34 THRD-F 200 CAST BRONZE GA-E- STR
LB 60628 WYE
Spectacle Blind 1/2 1+1/2 SP TB.5038 WAFER 600 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) Galvanized 60010 PEC
Spectacle Blind 2 4 SP TB.5038 WAFER 150 R.F. (125-250 FORGED ASTM A 105 GA-E- LNBDS
LB AARH) Galvanized 60010 PEC
Flange 1/2 1+1/2 ASME B16.5 FLG x THRD-F 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) Galvanized 60010
Flange 1/2 4 ASME B16.5 FLG x THRD-F 150 R.F. (125-250 FORGED ASTM A 105 GA-E- 1/2" to 1 1/2" size FLG
LB AARH) Galvanized 60010 Only for mating to
150# flanged conns.
Flange 2 2 ASME B16.5 FLG x THRD-F 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for mating to FLG
LB AARH) Galvanized 60010 300# flanged conns.
Flange Blind 1/2 1+1/2 ASME B16.5 FLG 600 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) Galvanized 60010 BLD
Flange Blind 2 4 ASME B16.5 FLG 150 R.F. (125-250 FORGED ASTM A 105 GA-E- FLG
LB AARH) Galvanized 60010 BLD
Flange Blind 2 2 ASME B16.5 FLG 300 R.F. (125-250 FORGED ASTM A 105 GA-E- Only for Press. Taps FLG
LB AARH) Galvanized 60010 on Equ't. BLD
45° Elbow 1/2 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- 45L
Galvanized 60010
90° Elbow 1/2 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- 90L
Galvanized 60010
Tee Equal 1/2 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- TEE
Galvanized 60010 STR
2
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:22 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Tee Reducing 3/4 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- TEE
Galvanized 60010 RED
1/2 3
Cap Female 1/2 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- CAP
Galvanized 60010
Coupling 1/2 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- CPL
Galvanized 60010
Coupling Reducing 3/4 4 ASME B16.11 THRD-F 3000# FORGED ASTM A 105 GA-E- CPL
Galvanized 60010
1/2 3
Plug Hex Head 1/2 4 ASME B16.11 THRD-M 3000# FORGED ASTM A 105 GA-E- PLG
Galvanized 60010 HEX
Union 1/2 4 MANUFACTURE STD THRD-F 3000# FORGED ASTM A 105 GA-E- UNN
Galvanized 60010
Gasket 1/2 1+1/2 ASME B16.20 FLG 600 R.F. (125-250 _ AISI 316 SPIRAL GA-E- GAS
LB AARH) WOUND/GRAPHITE 60012
Gasket 1/2 4 ASME B16.21 FLG 150 R.F. (125-250 _ ASBESTOS FREE - GA-E- 1/2" to 1-1/2" only GAS
LB AARH) KLINGERSIL C4400 60013 for mating to 150#
OR EQUAL flanged conns.
Gasket 1/2 2 ASME B16.20 FLG 300 R.F. (125-250 _ AISI 316 SPIRAL GA-E- Only for mating with GAS
LB AARH) WOUND/GRAPHITE 60012 300# flanged conns.
Nipple L=100 mm 1/2 4 SP TB.5383 A = THRD-M - THRD-M SEAMLESS ASTM A 53 GR. B GA-E- XS NIPP
Galvanized 60010
Nipple Reducing 3/4 4 SP TB.5382 A = THRD-M - THRD-M SEAMLESS ASTM A 53 GR. B GA-E- XS NIPP
Galvanized 60010
1/2 3
3
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:27 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 91A Branch Table 91A
TE
Branch 4 Branch
Size 3 TR TE TE Tee Equal
2 TR TR TE
TR Tee Reducing
1H TR TR TR TE
1 TR TR TR TR TE
TQ TR TR TR TR TR TE
H TR TR TR TR TR TR TE
4 3 2 1H 1 TQ H
Run Size
4
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:31 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:36 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:39 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 92R Branch Table 92R
Branch 12 TE Branch
Size 10 TR TE TE Tee Equal
8 TR TR TE
TR Tee Reducing
6 TR TR TR TE
4 TR TR TR TR TE
3 TR TR TR TR TR TE
2 TR TR TR TR TR TR TE
1H TR TR TR TR TR TR TR TE
1 TR TR TR TR TR TR TR TR TE
12 10 8 6 4 3 2 1H 1
Run Size
Sizes translation 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12
3
Snamprogetti S.p.A. PIPING CLASS PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:45 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
1
Snamprogetti S.p.A. PIPING CLASS DETAIL PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:49 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
2
Snamprogetti S.p.A. PIPING CLASS BRANCH PROJ: 312500 REV: 4 09/01/2006
PUMA5 04/01/2006 10:22:54 DOC: 00-GA-E-60001
Darquain Oil Field Development Size: Inc Thk: mm Temp: °C Pres: BAR Corr: mm
Chgd
Piping Class 93R Branch Table 93R
Branch 18 TE Branch
Size 16 TR TE TE Tee Equal
14 TR TR TE
TR Tee Reducing
12 TR TR TR TE
10 TR TR TR TR TE
8 TR TR TR TR TR TE
6 TR TR TR TR TR TR TE
4 TR TR TR TR TR TR TE
3 TR TR TR TR TR TR TE
2 TR TR TR TR TR TR TE
1H TR TR TR TR TR TR TR TE
1 TR TR TR TR TR TR TR TR TE
18 16 14 12 10 8 6 4 3 2 1H 1
Run Size
Sizes translation 1=1, 1H=1+1/2, 2=2, 3=3, 4=4, 6=6, 8=8, 10=10, 12=12, 14=14, 16=16, 18=18
3
VALVES AND FILTERS
DATA SHEETS
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60101
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60102
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60103
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60104
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60105
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60106
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60107
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60109
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60111
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60113
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60114
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60115
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60118
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60119
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60120
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60121
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60122
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60123
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60124
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60125
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60126
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60127
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60128
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60131
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60132
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 18
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60133
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60134
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 4
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60137
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60138
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60139
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60141
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60142
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60143
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 30 to 30
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.47 series.A
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60144
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60145
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design API602
end to end <MFR Std - Metallic>
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60148
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60149
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60154
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60155
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60156
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60157
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 24
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL900
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60158
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable,
and mfr.s standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the
indicated construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60160
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60161
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 24
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60162
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60163
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim Monel
Gate Seat-Face MONEL
Stem MONEL
Body Seat MONEL
Back-Seat MONEL
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60164
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150
ENDS BW / BW
trim Monel
Gate Seat-Face MONEL
Stem MONEL
Body Seat MONEL
Back-Seat MONEL
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60171
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60172
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60173
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60174
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60175
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60176
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60177
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60178
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60179
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60180
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60181
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60182
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60184
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60187
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60188
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60189
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60190
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60191
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60192
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60193
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60194
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60195
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60196
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60197
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Gate Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60198
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60199
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60200
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60201
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60202
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60203
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60205
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60206
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60207
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60210
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60211
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60212
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60213
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60214
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60216
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60217
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 10
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60218
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60219
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60220
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60221
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60222
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60224
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60225
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60226
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60227
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60228
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 6
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60229
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60230
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60231
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60232
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim Monel
Shutter Seat-Face MONEL
Stem MONEL
Body Seat MONEL
Back-Seat MONEL
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60233
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150
ENDS BW / BW
trim Monel
Shutter Seat-Face MONEL
Stem MONEL
Body Seat MONEL
Back-Seat MONEL
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60240
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60241
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60242
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60244
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60245
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all block
valves and the bleed valse is 1/4".
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60246
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1 to 1
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60247
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1/2 to 1/2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60248
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all block
valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60250
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60251
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60252
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60253
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60254
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60255
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60256
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Integral seat are admitted.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60257
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60258
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60259
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 8
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60260
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 12
CODES design BS1873
end to end BS2080
press. test BS6755 PART-1
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60261
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 12
CODES design ASME-B16.34
end to end ASME-B16.10
press. test API598
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60016
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
Client: Document No.: 00-GA-E-60262
Contractor:
PEDEC Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
---------------------------------------------------------------------------
Size 4” inch
Inlet-Outlet Bore 64.6 mm
NPS API 6A 2”+9/16 inch
---------------------------------------------------------------------------
Contractor:
PEDEC Consultant:
ADDITIONAL SPECIFICATION:
Contractor:
PEDEC Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
---------------------------------------------------------------------------
Size 4” inch
Inlet-Outlet Bore 64.6 mm
NPS API 6A 2”+9/16 inch
---------------------------------------------------------------------------
Contractor:
PEDEC Consultant:
ADDITIONAL SPECIFICATION:
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60305
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60306
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60307
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60310
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60311
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60312
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60313
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60314
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60315
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60316
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60317
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60318
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60017.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60319
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60322
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 18
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60323
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim Bronze
Shutter Seat-Face B-62
Hinge-Pin or Spring B-62
Body Seat B-62
SUPPL. TEST
NOTES
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60324
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 12
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60326
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60327
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60329
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60330
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60331
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60332
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60333
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 24
CODES design API594
end to end API594
press. test API598
RATING CL900 - RJ (F)
ENDS WAFER LUG / WAFER LUG as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60334
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60335
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design API594
end to end API594
press. test API598
RATING CL900 - RJ (F)
ENDS WAFER LUG / WAFER LUG as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60336
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API594
end to end API594
press. test API598
RATING CL1500 - RJ (F)
ENDS WAFER LUG / WAFER LUG as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60337
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim Monel
Shutter Seat-Face MONEL
Hinge-Pin or Spring MONEL
Body Seat MONEL
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60338
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design BS1868
end to end BS2080
press. test BS6755 PART-1
RATING CL150
ENDS BW / BW
trim Monel
Shutter Seat-Face MONEL
Hinge-Pin or Spring MONEL
Body Seat MONEL
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60345
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60346
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60348
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60349
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60350
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60351
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60352
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60353
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60354
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60355
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 20
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 13CR
Shutter Seat-Face 13CR
Hinge-Pin or Spring 13CR
Body Seat 13CR
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60356
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 24
CODES design API594
end to end API594
press. test API598
RATING CL600 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60357
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60358
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design API594
end to end API594
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60359
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60360
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design BS1868
end to end BS2080
press. test BS6755 PART-1
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60361
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 16
CODES design API594
end to end API594
press. test API598
RATING CL900 - RJ (F)
ENDS WAFER / WAFER as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Hinge-Pin or Spring 316
Body Seat 316
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60362
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Check-PS-Red B-Piston lift-Wldd seat - <MFR Std - Metallic> - CL2500 - BW
SIZE from 3 to 14
CODES design <MFR Std - Metallic>
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60016
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60363
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Check-PS-Red B-Piston lift-Wldd seat - <MFR Std - Metallic> - CL2500 - BW
SIZE from 12 to 14
CODES design <MFR Std - Metallic>
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- Valves shall be in accordance with GA-E-60017
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60364
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Austenitic Steel - Check-PS-Red B-Piston lift-Wldd seat - <MFR Std - Metallic> - CL2500 - BW
SIZE from 14 to 20
CODES design <MFR Std - Metallic>
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
Client: Document No.: 00-GA-E-60025
Contractor:
PEDEC Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
Contractor:
PEDEC Consultant:
CONTENT
1. 1. SCOPE......................................................................................................................... 3
Contractor:
PEDEC Consultant:
1. SCOPE
This document summarises the process and material Data Sheets for the supply
of Non Slam Nozzle Type CHECK valves for “DARQUAIN OIL FIELD”, Second
stage of Development, IRAN.
The valve design shall be suitable for any operating conditions (both minimum
and maximum) in order to ensure regular operation.
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
Nozzle Check valves, non-slam, metal seated, flanged RJ 6BX, sour + HIC
Design spec API SPEC 6A
Product spec level (PSL) 3
Mat. Classification EE
Type INTEGRAL BODY, VENTURI NOZZLE
Design spec, end FLANGED RJ 6BX
Design spec, face to face dim. MANUFACTURER STANDARD
Service SOUR
Service requirement NACE MR-01-75 + HIC (see GA-E-60017)
Standard of design API 6A (10000 psi)
Seat, design METAL SEATED
Mounting position HORIZONTAL
Spec treatm, body seat facing STELLITE 6
Spec treatm, cont area, disc STELLITE 6
Mat, body ASTM A 694 F60
Mat, trim SS 316/STELLITE 6
SS 316L/STELLITE 6
NITRONIC 50 / STELLITE 6
Mat, disc ASTM A 694 F60 + STELLITE 6
Mat, spring INCONEL X750
Mat, wetted parts STAINLESS STEEL 316
STAINLESS STEEL 316L
Mat spec, body seat ring AISI 316 L + STELLITE 6
Mat spec, guide road AISI 316 / AISI 316 L / ASTM A182 GRADE F XM-19
Mat spec, spring ASTM B637 UNS N07750
Mat spec, wetted parts AISI 316
Client: Document No.: 00-GA-E-60025
Contractor:
PEDEC Consultant:
AISI 316 L
NITRONIC 50
Contractor:
PEDEC Consultant:
Nozzle Check valves, non-slam, metal seated, flanged RJ 6BX, sour + HIC
Design spec API SPEC 6A
Product spec level (PSL) 3
Mat. Classification EE
Type INTEGRAL BODY, VENTURI NOZZLE
Design spec, end FLANGED RJ 6BX
Design spec, face to face dim. MANUFACTURER STANDARD
Service SOUR
Service requirement NACE MR-01-75 + HIC (see GA-E-60017)
Standard of design API 6A (10000 psi)
Seat, design METAL SEATED
Mounting position HORIZONTAL
Spec treatm, body seat facing STELLITE 6
Spec treatm, cont area, disc STELLITE 6
Mat, body ASTM A 694 F60
Mat, trim SS 316/STELLITE 6
SS 316L/STELLITE 6
NITRONIC 50 / STELLITE 6
Mat, disc ASTM A 694 F60 + STELLITE 6
Mat, spring INCONEL X750
Mat, wetted parts STAINLESS STEEL 316
STAINLESS STEEL 316L
Mat spec, body seat ring AISI 316 L + STELLITE 6
Mat spec, guide road AISI 316 / AISI 316 L / ASTM A182 GRADE F XM-19
Client: Document No.: 00-GA-E-60025
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
Nozzle Check valves, non-slam, metal seated, flanged RJ 6BX, sour + HIC
Design spec API SPEC 6A
Product spec level (PSL) 3
Mat. Classification EE
Type INTEGRAL BODY, VENTURI NOZZLE
Design spec, end FLANGED RJ 6BX
Design spec, face to face dim. MANUFACTURER STANDARD
Service SOUR
Service requirement NACE MR-01-75 + HIC (see GA-E-60016)
Standard of design API 6A (10000 psi)
Seat, design METAL SEATED
Mounting position HORIZONTAL
Spec treatm, body seat facing STELLITE 6
Spec treatm, cont area, disc STELLITE 6
Mat, body ASTM A 694 F60
Mat, trim SS 316/STELLITE 6
SS 316L/STELLITE 6
NITRONIC 50 / STELLITE 6
Mat, disc ASTM A 694 F60 + STELLITE 6
Mat, spring INCONEL X750
Mat, wetted parts STAINLESS STEEL 316
STAINLESS STEEL 316L
Mat spec, body seat ring AISI 316 L + STELLITE 6
Mat spec, guide road AISI 316 / AISI 316 L / ASTM A182 GRADE F XM-19
Mat spec, spring ASTM B637 UNS N07750
Client: Document No.: 00-GA-E-60025
Contractor:
PEDEC Consultant:
Contractor:
PEDEC Consultant:
st
Fluid Flash Gas Compr. 1 Stg. Discharge Gas
Phase Gas
Design Temperature (°C) 207
Design Pressure (barg) 44
Nozzle Check valves, non-slam, metal seated, flanged RF 125 AARH, sour + HIC
Design spec ASME B 16.34 / MANUFACTURER STD.
Type INTEGRAL BODY, VENTURI NOZZLE
Design spec, end FLANGED RF 125 AARH (ASME B16.5)
Design spec, face to face dim. MANUFACTURER STANDARD
Service SOUR
Service requirement NACE MR-01-75 + HIC (see GA-E-60017)
Standard of Design 300 LBS
Seat, design METAL SEATED
Mounting position HORIZONTAL
Spec treatm, body seat facing INCONEL 625
Spec treatm, cont area, disc INCONEL 625
Mat, body ASTM A 216 GR.WCB
Mat, trim INCONEL 625
Contractor:
PEDEC Consultant:
nd
Fluid Flash Gas Compr. 2 Stg. Discharge Gas
Phase Gas
Design Temperature (°C) 203
Design Pressure (barg) 85
Contractor:
PEDEC Consultant:
nd
Fluid Gas from 2 Stg. Separator
Phase Gas
Design Temperature (°C) 123
Design Pressure (barg) 42
Contractor:
PEDEC Consultant:
st
Fluid Flash Gas Compr. 1 Stg. Discharge
Phase Mixed
Design Temperature (°C) 90
Design Pressure (barg) 44
Contractor:
PEDEC Consultant:
nd
Fluid Flash Gas Compr. 2 Stg. Discharge
Phase Gas
Design Temperature (°C) 90
Design Pressure (barg) 85
Contractor:
PEDEC Consultant:
st
Fluid Gas from 1 Stg. Separator
Phase Gas
Design Temperature (°C) 128
Design Pressure (barg) 85
Contractor:
PEDEC Consultant:
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60400
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60401
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60402
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- All materials must be as per NACE MR0103 latest edition.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60403
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- All materials must be as per NACE MR0103 latest edition.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60410
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60411
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 20
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60412
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Austenitic Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1/2 to 1/2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- Valves shall be in accordance with GA-E-60014.
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60413
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all block
valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60414
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Austenitic Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1/2 to 2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A182 F316 - -/NACE
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all block
valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60415
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Austenitic Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1 to 1
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60416
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60420
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE+HIC
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60421
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1/2 to 1/2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60422
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE+HIC
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60423
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1 to 1
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60425
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60426
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60427
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60428
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 12
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60431
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60432
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60433
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Austenitic Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A182 F316 - -/NACE
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60434
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60435
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 18
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60436
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Copper - Bronze Ball-End entry-FB-Floating ball - <MFR Std - Metallic> - CL200 - THDF
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60438
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60439
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60440
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60441
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60444
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design API6D
end to end API6D
press. test API6D
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60445
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM B564 UNS N06625 (Ann.) - -/NACE
NOTES
--The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60446
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL800 - SWxTHDF
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM B564 UNS N06625 (Ann.) - -/NACE
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60447
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Nickel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60448
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Nickel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125 µin.Ra
SIZE from 1 to 1
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60449
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60450
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60451
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 3 to 20
CODES design API6D
end to end API6D
press. test API6D
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60452
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Nickel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL1500 - RJ (F)
SIZE from 2 to 2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM B564 UNS N06625 (Ann.) - -/NACE
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60453
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API6D
end to end API6D
press. test API6D
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60454
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60455
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL1500 - RJ (F)
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE
trim 316
Shutter Seat-Face 316
Stem 316
Body Seat 316
Back-Seat 316
Packing GRAPHITE
SUPPL. TEST
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60456
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60021.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60461
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60462
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60464
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed SLIM valve-Wafer-OS&Y primary valve - <MFR Std> - CL600 - RF - 125
µin.Ra
SIZE from 1 to 1
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / THDF as per ASME-B16.5
NOTES
-- Primary valve is needle type and OS&Y construction. The secondary process valve
shall be of same dimension of primary valve. The bleed valve dimension shall be 1/2". For SLIM
valve with outlet threaded shall have a female thread joint of 1/2" NPT.
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60466
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
Carbon Steel - DBL Block&Bleed Needle vlv-UB-One piece bdy -RB- - <MFR Std> - CL600 - RF - 125 µin.Ra
SIZE from 1 to 2
CODES design <MFR Std>
end to end <MFR Std>
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
CHARACTERISTICS Body-Bonnet/End-Joint --
Shutter type NEEDLE
Seat type INTEGRAL
MATERIALS body ASTM A105 - -/NACE+HIC
NOTES
-- The Double Block & Bleed shall have the bleed valve of needle type. The valve dimensions is same for all
block valves and the bleed valve is 1/2".
-- Valves design to be Mfr's Standard/BS5352 as far as applicable & of Firesafe Design to API 607
Rev.4/BS6755 Part 2. Primary valves having a 'bolted gland' design shall have a 'live loaded'
gland bolt arrangement to maintain a permanent stem-packing stress, a 'bellows sealed' design
would be an acceptable alternative.
-- Valves shall be Hydrostatically & Pneumatically tested to BS6755 part 1 leakage rate 'A'.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60467
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60468
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60469
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60017.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60470
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60017.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60471
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60472
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60473
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60474
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60475
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60476
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60477
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60017
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60478
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 24
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60017
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60481
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 4
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60482
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 6 to 12
CODES design API6D
end to end API6D
press. test API6D
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Face-to-Face or End-to-End dimensions shall be according with API 6D. Short dimensions are Not admitted.
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
N.I.O.C. (PEDEC) 312500
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E-60489
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60500
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 4 to 24
CODES design API609
end to end API609
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER / WAFER as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60501
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Butterfly-Flanged-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
SIZE from 16 to 24
CODES design API609
end to end <MFR Std - Metallic>
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60503
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Butterfly-Lug wafer-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
SIZE from 3 to 14
CODES design API609
end to end API609
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS WAFER LUG / WAFER LUG as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60504
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Butterfly-Flanged-Triple Off Set-Int.seat-Fire safe - API609 - CL150 - RF - 125 µin.Ra
SIZE from 16 to 24
CODES design API609
end to end <MFR Std - Metallic>
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60505
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Carbon Steel - Butterfly-Lug wafer-Triple Off Set-Int.seat-Fire safe - API609 - CL300 - RF - 125 µin.Ra
SIZE from 3 to 16
CODES design API609
end to end API609
press. test API598
RATING CL300 - RF - 125 µin.Ra
ENDS WAFER LUG / WAFER LUG as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60017
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60516
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design API600
end to end ASME-B16.10
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
trim 13CR
Gate Seat-Face 13CR
Stem 13CR
Body Seat 13CR
Back-Seat 13CR
Packing GRAPHITE
SUPPL. TEST
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60517
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The end-to-end or face-to-face dimensions are in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60518
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60519
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 16
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL900 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60520
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 14
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL2500
ENDS BW / BW
NOTES -- The valve shall comply with specification of this sheet, the Snamprogetti STD.TB.VAL.5801 and the indicated
construction Code.
-- The valves construction and testing shall be in accordance with indicated Code, where applicable, and mfr.s
standard.
-- The valves shall be supplied with manual gear-operator, according to Snamprogetti STD.TB.5802
-- Valves shall be in accordance with GA-E-60016
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
Client: Document No.: 00-GA-E-60521
Contractor:
PEDEC Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Size 2” inch
Inlet-Outlet Bore 30.8 mm
NPS API 6A 1”+13/16 inch
---------------------------------------------------------------------------
Contractor:
PEDEC Consultant:
---------------------------------------------------------------------------
Size 3” inch
Inlet-Outlet Bore 49 mm
NPS API 6A 2”+1/16 inch
---------------------------------------------------------------------------
Size 4” inch
Inlet-Outlet Bore 64.6 mm
NPS API 6A 2”+9/16 inch
---------------------------------------------------------------------------
ADDITIONAL SPECIFICATION:
Contractor:
PEDEC Consultant:
ENI Iran B.V NATIONAL IRANIAN OIL COMPANY ( N.I.O.C )
PETROLEUM ENGINEERING & DEVELOPMENT COMPANY Snamprogetti S.p.A.
NICO DARQUAIN OIL FIELD SAZEH ENGINEERS. ARCHITECTS.
CONSULTANTS
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Size 2” inch
Inlet-Outlet Bore 23.9 mm
NPS API 6A 1”+13/16 inch
--------------------------------------------------------------------------------
Contractor:
PEDEC Consultant:
----------------------------------------------------------------------
Size 3” inch
Inlet-Outlet Bore 42.1 mm
NPS API 6A 1”+13/16 inch
---------------------------------------------------------------------------
Size 4” inch
Inlet-Outlet Bore 57.7 mm
NPS API 6A 2”+9/16 inch
---------------------------------------------------------------------------
---------------------------------------------------------------------------
---------------------------------------------------------------------------
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Size 24” inch
Inlet-Outlet Bore 368.7 mm
NPS API 6A 16”+ 3/4 inch
---------------------------------------------------------------------------
Client: Document No.: 00-GA-E-600522
Contractor:
PEDEC Consultant:
ADDITIONAL SPECIFICATION:
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60600
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60601
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60602
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design <MFR Std - Metallic>
end to end ASME-B16.9
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS BW / BW as per ASME-B16.5
cover / other FLGD
CHARACTERISTICS Body-Bonnet/End-Joint BOLTED BONNET
MATERIALS body ASTM A234 WPB - SMLS - -/NACE
NOTES -- The ratio of filtering area to the bore of the T-strainer shall be equal to 2:1 minimum.
A pup-piece between body and cover flange is allowed to obtain the required filtering area ratio.
-- End and/or bonnet flanges shall be welded to the body. Flanges shall be of the forged butt-welding type. The
welds and qualifications for the welding procedure and the welder or welding operator shall conform to the
requirements of ASME B31.3 .
-- The material of connection and blind flanges shall be forged and equivalent to the wrought material of the body.
-- A flow arrow shall be marked on each body strainer.
-- The required thickness in order is referred to the equivalent pipe of line.
-- Valves shall be in accordance with GA-E-60014.
-- Drain connection for NPS 6" & larger shall be 1" NPT.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60603
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60604
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60017.
-- Filters shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60605
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design <MFR Std - Metallic>
end to end ASME-B16.9
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS BW / BW as per ASME-B16.5
cover / other FLGD
CHARACTERISTICS Body-Bonnet/End-Joint BOLTED BONNET
MATERIALS body ASTM A234 WPB - SMLS - -/NACE+HIC
NOTES -- The ratio of filtering area to the bore of the T-strainer shall be equal to 2:1 minimum.
A pup-piece between body and cover flange is allowed to obtain the required filtering area ratio.
-- End and/or bonnet flanges shall be welded to the body. Flanges shall be of the forged butt-welding type. The
welds and qualifications for the welding procedure and the welder or welding operator shall conform to the
requirements of ASME B31.3 .
-- The material of connection and blind flanges shall be forged and equivalent to the wrought material of the body.
-- A flow arrow shall be marked on each body strainer.
-- The required thickness in order is referred to the equivalent pipe of line.
-- T-Filter shall be in accordance with GA-E-60017.
-- Drain connection for NPS 6" & larger shall be 1" NPT.
-- T-Filter shall have a minimun of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60607
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60608
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60609
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60610
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60611
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60612
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60017.
-- Filters shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60613
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60614
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60615
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60616
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design <MFR Std - Metallic>
end to end ASME-B16.9
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS BW / BW as per ASME-B16.5
cover / other FLGD
CHARACTERISTICS Body-Bonnet/End-Joint BOLTED BONNET
MATERIALS body ASTM A234 WPB - SMLS - -/NACE+HIC
NOTES -- The ratio of filtering area to the bore of the T-strainer shall be equal to 2:1 minimum.
A pup-piece between body and cover flange is allowed to obtain the required filtering area ratio.
-- End and/or bonnet flanges shall be welded to the body. Flanges shall be of the forged butt-welding type. The
welds and qualifications for the welding procedure and the welder or welding operator shall conform to the
requirements of ASME B31.3 .
-- The material of connection and blind flanges shall be forged and equivalent to the wrought material of the body.
-- A flow arrow shall be marked on each body strainer.
-- The required thickness in order is referred to the equivalent pipe of line.
T-Filter shall be in accordance with GA-E-60016.
Drain connection for NPS 6" & larger shall be 1" NPT.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60617
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60618
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60619
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0 1
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60620
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end <MFR Std - Metallic>
press. test ASME-B16.34
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60621
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60622
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 3 to 24
CODES design <MFR Std - Metallic>
end to end ASME-B16.9
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS BW / BW as per ASME-B16.5
cover / other FLGD
CHARACTERISTICS Body-Bonnet/End-Joint BOLTED BONNET
MATERIALS body ASTM A234 WPB - SMLS - -/NACE+HIC
NOTES -- The ratio of filtering area to the bore of the T-strainer shall be equal to 2:1 minimum.
A pup-piece between body and cover flange is allowed to obtain the required filtering area ratio.
-- End and/or bonnet flanges shall be welded to the body. Flanges shall be of the forged butt-welding type. The
welds and qualifications for the welding procedure and the welder or welding operator shall conform to the
requirements of ASME B31.3 .
-- The material of connection and blind flanges shall be forged and equivalent to the wrought material of the body.
-- A flow arrow shall be marked on each body strainer.
-- The required thickness in order is referred to the equivalent pipe of line.
-- Valves shall be in accordance with GA-E-60016.
-- Drain connection for NPS 6" & larger shall be 1" NPT.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60623
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60624
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60625
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60626
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60627
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60628
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
Copper - Bronze Y Strainer - Union bonnet - <MFR Std - Metallic> - CL200 - THDF
NOTES
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60629
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60630
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60631
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 14 to 24
CODES design <MFR Std - Metallic>
end to end ASME-B16.9
press. test API598
RATING CL150 - RF - 125 µin.Ra
ENDS BW / BW as per ASME-B16.5
cover / other FLGD
CHARACTERISTICS Body-Bonnet/End-Joint BOLTED BONNET
MATERIALS body ASTM A234 WPB - SMLS - -/NACE+HIC
NOTES -- The ratio of filtering area to the bore of the T-strainer shall be equal to 2:1 minimum.
A pup-piece between body and cover flange is allowed to obtain the required filtering area ratio.
-- End and/or bonnet flanges shall be welded to the body. Flanges shall be of the forged butt-welding type. The
welds and qualifications for the welding procedure and the welder or welding operator shall conform to the
requirements of ASME B31.3 .
-- The material of connection and blind flanges shall be forged and equivalent to the wrought material of the body.
-- A flow arrow shall be marked on each body strainer.
-- The required thickness in order is referred to the equivalent pipe of line.
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60017.
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60632
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60633
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60634
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60017.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60635
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60636
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60637
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60638
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL600 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60016.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60639
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60640
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 10
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall be in accordance with GA-E-60014.
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60641
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 12
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL150 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60642
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60643
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL1500 - RJ (F)
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
- Valves shall be in accordance with GA-E-60014
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005
CUSTOMER JOB
PLANT LOCATION
DARQUAIN OIL FIELD, IRAN SPC.GA-E- 60644
PROJECT / UNIT Rev.
SECOND PHASE OF DEVELOPMENT Sh. 1 of 1 0
SIZE from 2 to 2
CODES design ASME-B16.34
end to end ASME-B16.10
press. test ASME-B16.34
RATING CL300 - RF - 125 µin.Ra
ENDS FLGD / FLGD as per ASME-B16.5
NOTES -- The strainer shall comply with specification of this sheet and the Snamprogetti STD.TB.5701 .
-- Valves shall have a minimum of 6mm corrosion allowance for all pressure containing parts.
-- Valves shall be in accordance with GA-E-60016
0 Not Issued
This document is the property of Snamprogetti who will safeguard its rights according to the civil and penal provisions of the law. Report Name: SpcVlv.rep
Revision: 00.01.02 - 06/04/2005