Академический Документы
Профессиональный Документы
Культура Документы
BURNDY® Products
www.fciconnect.com
BURNDY® Products
Ground
Rods/
Rebar GAR GRC GP GK
The GAR is a Fence Post The GRC High Strength Ground The GP is a range-taking ground The GK connector is a ground
Grounding Connector. It is a Rod Clamp is a range-taking connector for joining two parallel connector for joining three equal
range-taking ground connector ground connector for joining a cables to a rod, pipe or column in cables to a rod or tube in a
for joining cable to rod or tube in single copper cable to a copper, a perpendicular configuration. parallel configuration. Acceptable
parallel or right angle configura- copper clad steel, galvanized for direct burial in earth or
tions. steel, or stainless steel ground concrete.
Static
Ground
GIE-G GRF GP-RT
The GIE-G is a temporary clamp for grounding gasoline trucks, tank The GRF is range-taking and is Our GP1726RT is range-taking and
cars, aircraft and other vehicles where the danger of igniting designed for joining one or two designed for joining 1 or 2 conductors
combustibles due to static electricity discharge exists. This connector conductors to a round or square to a round or square pedestal in all
is designed to penetrate thin coats of paint and light corrosion to pedestal in all raised flooring raised flooring systems. This unique,
make electrical contact. systems. patented connector is designed to
penetrate painted pedestals to
establish electrical contact.
Bus Bar/
Flat Bar
KC GB GBM GC GCM
The KC SERVIT POST™ is used The GB is a range-taking con- The GBM type connector clamps The GC is a range-taking con- The GCM type connector clamps
to ground 1 or 2 cables to steel nector used for joining a single the cable directly onto the bus nector for joining two parallel the cables directly onto the bus
structure, fence post, and trans- conductor to 1/4” thick bus bar. bar surface. cables to a 1/4” thick bus bar. Its bar surface.
formers. They can also be used Its two piece design separates two piece design separates the
to tap 1 or 2 cables from a the cable from the bus bar. cables from the bus bar.
drilled and taped bus bar.
Fence
Post, GC-A
Piping &
GP GK GD Low Cost Water Pipe Clamps
Tubing The GP is range-taking ground The GK connector is a ground con- The GD is a range-taking Low cost water pipe connectors are used for connecting grounding conduc-
tor to water pipe or copper tube. The cast bronze ground clamps come with
connector for joining two paral- nector for joining three equal connector for joining two cables
lel cables to a rod, pipe or cables to a rod or tube in a paral- to a rod or pipe in a parallel either silicon bronze hardware or brass hardware. Clamps with silicon
column in a perpendicular lel configuration. Acceptable for configuration. bronze hardware are UL467 Listed for direct burial in earth or concrete.
There is also a line of cast bronze clamps for use with conduit. These are
configuration. direct burial in earth or concrete.
used for grounding rigid conduit systems and come with zinc
plated hardware.
GC-A
The GC-A dual rated ground clamps are used for copper and aluminum
cable. GC-A ground clamps are UL Listed for attaching either copper or
aluminum conductors to copper water pipe, galvanized pipe or steel conduit.
Cable
Cable & Braid Tray
Rail/H-Beam Transformer
EQC KC QGFL
GA-H J & RGC The KC SERVIT POST™ is used
The EQC is an eye-in-basket, The QGFL BARTAP™ is an eye-
The GA-H is a range-taking The RGC connectors are tin to ground one or two cables to
range-taking connector that in-basket connector for joining a
connector for joining a single plated mechanical clamp steel structure, fence post, and
fits all standard EEI and NEMA single cable to a bus bar or pad.
cable to an “H” beam or square connectors. Unlike the RGC transformers. They can also
distribution transformers as a B1 and B2 versions are available
tube in a parallel configuration. Series, the J Series requires a be used to tap 1 or 2 cables
tank ground terminal. to differentiate stud size options.
terminal in its installation. from a drilled and tapped bus
bar.
GAR3902-BU GAR3902
The Mechanical Grounding line is a family of direct burial, UL Listed connectors. Made of high copper
content alloys, they use a nut and bolt design to provide the means for connecting copper cable to
many applications. Only the finest high copper alloys are used to ensure performance under the most
Fence extreme environmental conditions. Where the direct burial symbol appears, that connector is capable
of direct burial applications in earth or embedment in concrete.
Post,
Over 75 years of technological innovations make FCI-BURNDY ® Mechanical Grounding Connectors
Piping & one of the most widely used, specified and highly respected lines in the industry. There are virtually no
Tubing grounding or bonding application problems that our products cannot solve. All FCI-BURNDY ®
Mechanical Grounding Connectors are designed for easy installation and outstanding durability.
continued
The Direct Burial Symbol indicates that the connector is suitable for burial in
Earth or concrete.
The Underwriters Laboratories symbol indicates that the connector meets the
noted UL standard.
GG
The GG is for joining braid, bar,
The CSA symbol indicates that the connector meets the applicable standards
strap, or cable to a rod or tube. of the Canadian Standards Association.
1 2 5 2 5
Pool/ 3 8
Spa 9
4 10
CL50-1
The copper Lay-in Lug is
designed for grounding or bond-
ing copper conductor to steel
frame or other metal surfaces
where a continuous run is
preferable.
YGS
The YGS is an in-line splice
specifically designed for NEC
and other code ground applica-
tions. This terminal features an
inspection hole to ensure proper
cable insertion.
7 FCI BURNDY® Products provides bonding solutions for swimming pools and spas. FCI BURNDY®
Products offers a complete pool and spa package that meets the requirements of NEC Article 680,
8 Swimming Pools, Fountains and Similar Installations, and UL467, Grounding and Bonding Equipment.
Article 250, Grounding, states that grounding conductors and bonding jumpers shall be connected by
exothermic welding, listed pressure connectors, listed clamps or other listed means.
6 Additionally, Article 680 requires that bonding of all electrical conductive surfaces must be maintained
within five (5) feet horizontally of the inside walls of the pool. Bonding covers the drain, rebar, water
inlet pipe, skimmer, ladder, slides, diving structure, underwater lighting, junction boxes (if within 5 feet),
YGC and/or water circulating/heating equipment.
The YGC "C" Tap CRIMPIT® is
manufactured from ETP copper
and incorporates a "massive
design copper extrusion" for
minimum connection resistance.
Application/Users
If you would like to contact one of the users noted in this section, please call our
Marketing Department at 1-800-346-4175 and we’ll put you in touch.
www.fciconnect.com
BURNDY® Products